Unitronics V530-53-B20B Mode d'emploi

Marque: Unitronics

Modèle: V530-53-B20B

Taper: Mode d'emploi

Unitronics

Vision™ OPLC™

User Guide

V530-53-B20B

This guide provides basic information for Unitronics’ controller V530-53-B20B.

General Description

V530 OPLCs are programmable logic controllers that comprise a built-in operating panel containing a

monochrome touchscreen, which displays a virtual keyboard when the application requires the

operator to enter data.

Communications

▪ 2 serial ports: RS232 (COM 1), RS232/485 (COM 2)

▪ 1 CANbus port

▪ The user can order and install an additional port. Available port types

are: RS232/RS485, and Ethernet

▪ Communication Function Blocks include: SMS, GPRS, MODBUS

serial/IP Protocol FB enables PLC to communicate with almost any

external device, via serial or Ethernet communications

I/O Options

V530 supports digital, high-speed, analog,

weight and temperature measurement I/Os

via:

▪ Snap-in I/O Modules

Plug into the back of the controller to

provide an on-board I/O configuration

▪ I/O Expansion Modules

Local or remote I/Os may be added via

expansion port or CANbus

Installation instructions and other data may be found in the module’s technical

specification sheet.

Information

Mode

This mode enables you to:

▪ View & Edit operand values, COM port settings, RTC and screen

contrast/brightness settings

▪ Calibrate the touchscreen

▪ Stop, initialize, and reset the PLC

To enter Information Mode, press the <i> button for several seconds.

Programming

Software,

& Utilities

The Unitronics Setup CD contains VisiLogic software and other utilities

▪ VisiLogic

Easily configure hardware and write both HMI and Ladder control

applications; the Function Block library simplifies complex tasks such

as PID. Write your application, and then download it to the controller

via the programming cable included in the kit.

▪ Utilities

Includes UniOPC server, Remote Access for remote programming

and diagnostics, and DataXport for run-time data logging.

To learn how to use and program the controller, as well as use utilities such as

Remote Access, refer to the VisiLogic Help system.

Data Tables

Data tables enable you to set recipe parameters and create datalogs.

Additional product documentation is in the Technical Library, located at www.unitronicsplc.com.

Technical support is available at the site, and from support@unitronics.com.

Vision™ OPLC™ V530-53-B20B

Unitronics

Standard Kit Contents

Vision controller

Battery (not installed)

3 pin power supply connector

Mounting brackets (x4)

5 pin CANbus connector

Rubber seal

CANbus network termination resistor

Danger Symbols

When any of the following symbols appear, read the associated information carefully.

Symbol

Meaning

Description

Danger

The identified danger causes physical and property damage.

Warning

The identified danger could cause physical and property damage.

Caution

Use caution.

▪ Before using this product, the user must read and understand this document.

▪ All examples and diagrams are intended to aid understanding, and do not guarantee operation.

Unitronics accepts no responsibility for actual use of this product based on these examples.

▪ Please dispose of this product according to local and national standards and regulations.

▪ Only qualified service personnel should open this device or carry out repairs.

Failure to comply with appropriate safety guidelines can cause severe injury or property damage.

▪ Do not attempt to use this device with parameters that exceed permissible levels.

▪ To avoid damaging the system, do not connect/disconnect the device when power is on.

Environmental Considerations

▪ Do not install in areas with: excessive or conductive dust, corrosive or flammable gas,

moisture or rain, excessive heat, regular impact shocks or excessive vibration, in

accordance with the standards given in the product’s technical specification sheet.

▪ Ventilation: 10mm space required between controller’s top/bottom edges & enclosure walls.

▪ Do not place in water or let water leak onto the unit.

▪ Do not allow debris to fall inside the unit during installation.

▪ Install at maximum distance from high-voltage cables and power equipment.

UL Compliance

The following section is relevant to Unitronics’ products that are listed with the UL.

The following models: V530-53-B20B, V530-53-B20B-J are UL listed for Ordinary Location.

UL Ordinary Location

In order to meet the UL ordinary location standard, panel-mount this device on the flat surface

of Type 1 or 4 X enclosures

Installation Guide

Unitronics

UL Ratings, Programmable Controllers for Use in Hazardous Locations,

Class I, Division 2, Groups A, B, C and D

These Release Notes relate to all Unitronics products that bear the UL symbols used to mark products

that have been approved for use in hazardous locations, Class I, Division 2, Groups A, B, C and D.

Caution

▪ This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D, or Non-

hazardous locations only.

▪ Input and output wiring must be in accordance with Class I, Division 2 wiring methods and in

accordance with the authority having jurisdiction.

▪ WARNING—Explosion Hazard—substitution of components may impair suitability for Class I,

Division 2.

▪ WARNING – EXPLOSION HAZARD – Do not connect or disconnect equipment unless power

has been switched off or the area is known to be non-hazardous.

▪ WARNING – Exposure to some chemicals may degrade the sealing properties of material

used in Relays.

▪ This equipment must be installed using wiring methods as required for Class I, Division 2 as

per the NEC and/or CEC.

Panel-Mounting

For programmable controllers that can be mounted also on panel, in order to meet the UL Haz Loc

standard, panel-mount this device on the flat surface of Type 1 or Type 4X enclosures.

Communication and Removable Memory Storage

When products comprise either USB communication port, SD card slot, or both, neither

the SD card slot nor the USB port are intended to be permanently connected, while the USB port is

intended for programming only.

Removing / Replacing the battery

When a product has been installed with a battery, do not remove or replace the battery unless the

power has been switched off, or the area is known to be non-hazardous.

Please note that it is recommended to back up all data retained in RAM, in order to avoid losing data

when changing the battery while the power is switched off. Date and time information will also need to

be reset after the procedure.

UL des zones ordinaires:

Pour respecter la norme UL des zones ordinaires, monter l'appareil sur une surface plane de type de

protection 1 ou 4X

Certification UL des automates programmables, pour une utilisation en

environnement à risques, Class I, Division 2, Groups A, B, C et D.

Cette note fait référence à tous les produits Unitronics portant le symbole UL - produits qui ont été

certifiés pour une utilisation dans des endroits dangereux, Classe I, Division 2, Groupes A, B, C et D.

Attention

▪ Cet équipement est adapté pour une utilisation en Classe I, Division 2, Groupes A, B, C et

D, ou dans Non-dangereux endroits seulement.

▪ Le câblage des entrées/sorties doit être en accord avec les méthodes

de câblage selon la Classe I, Division 2 et en accord avec l’autorité compétente.

Vision™ OPLC™ V530-53-B20B

Unitronics

▪ AVERTISSEMENT: Risque d’Explosion – Le remplacement de certains composants rend

caduque la certification du produit selon la Classe I, Division 2.

▪ AVERTISSEMENT - DANGER D'EXPLOSION - Ne connecter pas ou ne débranche pas

l'équipement sans avoir préalablement coupé l'alimentation électrique ou la zone est

reconnue pour être non dangereuse.

▪ AVERTISSEMENT - L'exposition à certains produits chimiques peut dégrader les propriétés

des matériaux utilisés pour l'étanchéité dans les relais.

▪ Cet équipement doit être installé utilisant des méthodes de câblage suivant la norme Class I,

Division 2 NEC et /ou CEC.

Montage de l'écran:

Pour les automates programmables qui peuvent aussi être monté sur l'écran,

pour pouvoir être au standard UL, l'écran doit être monté dans un coffret avec une surface plane de

type 1 ou de type 4X.

Communication et de stockage amovible de mémoire (carte mémoire)

Produits comprend un port USB de communication, soit un port carte SD ou les deux, ni le port SD, ni

le port USB ne sont censés être utilisés en permanence, tandis que l'USB est destiné à la

programmation uniquement.

Retrait / Remplacement de la batterie

Lorsqu'un produit a été installé avec une batterie, retirez et remplacez la batterie seulement si

l’alimentation est éteinte ou si l’environnement n’est pas dangereux.

Veuillez noter qu'il est recommandé de sauvegarder toutes les données conservées dans la RAM, afin

d'éviter de perdre des données lors du changement de la batterie lorsque l'alimentation est coupée.

Les informations sur la date et l'heure devront également être réinitialisées après la procédure

Inserting the Battery

In order to preserve data in case of power-off, you must insert the battery.

The battery is supplied taped to the battery cover on the rear of the controller.

1. Remove the battery cover shown on page 4. The polarity (+) is marked on the battery holder and

on the battery.

2. Insert the battery, ensuring that the polarity symbol on the battery is:

- facing up

- aligned with the symbol on the holder

3. Replace the battery cover.

Installation Guide

Unitronics

Mounting

Dimensions

Vision™ OPLC™ V530-53-B20B

Unitronics

Panel Mounting

Before you begin, note that the mounting panel cannot be more than 5 mm thick.

1. Make a panel cut-out according

to the dimensions in the figure to

the right.

2. Slide the controller into the cut-

out, ensuring that the rubber seal

is in place.

3. Push the 4 mounting brackets

into their slots on the sides of the

controller as shown in the figure

to the right.

4. Tighten the bracket screws

against the panel. Hold the

bracket securely against the unit

while tightening the screw.

5. When properly mounted, the

controller is squarely situated in

the panel cut-out as shown

below.

Installation Guide

Unitronics

Wiring

▪ Do not touch live wires.

▪ Install an external circuit breaker. Guard against short-circuiting in external wiring.

▪ Use appropriate circuit protection devices.

▪ Unused pins should not be connected. Ignoring this directive may damage the device.

▪ Double-check all wiring before turning on the power supply.

Caution

▪ To avoid damaging the wire, do not exceed a maximum torque of 0.5 N·m (5 kgf·cm).

▪ Do not use tin, solder, or any substance on stripped wire that might cause

the wire strand to break.

▪ Install at maximum distance from high-voltage cables and power equipment.

Wiring Procedure

Use crimp terminals for wiring; use 26-12 AWG wire (0.13 mm 2–3.31 mm2).

1. Strip the wire to a length of 7±0.5mm (0.250–0.300 inches).

2. Unscrew the terminal to its widest position before inserting a wire.

3. Insert the wire completely into the terminal to ensure a proper connection.

4. Tighten enough to keep the wire from pulling free.

▪ Input or output cables should not be run through the same multi-core cable or share the same wire.

▪ Allow for voltage drop and noise interference with input lines used over an extended distance. Use

wire that is properly sized for the load.

Power Supply

The controller requires an external 12 or 24VDC power supply. The permissible input voltage

range is 10.2-28.8VDC, with less than 10% ripple.

▪ A non-isolated power supply can be used if a 0V signal is connected to the chassis.

▪ Install an external circuit breaker. Guard against short-

circuiting in external wiring.

▪ Double-check all wiring before turning on the power

supply.

▪ Do not connect either the ‘Neutral or ‘Line’ signal of the

110/220VAC to device’s 0V pin.

▪ In the event of voltage fluctuations or non-conformity to

voltage power supply specifications, connect the

device to a regulated power supply.

Earthing the Power Supply

To maximize system performance, avoid electromagnetic interference by:

▪ Mounting the controller on a metal panel.

▪ Earthing the controller’s power supply: connect one end of a 14 AWG wire to the chassis

signal; connect the other end to the panel.

Note: If possible, the wire used to earth the power supply should not exceed 10 cm in length.

However, it is recommended to earth the controller in all cases.

Vision™ OPLC™ V530-53-B20B

Unitronics

Communication Ports

▪ Turn off power before changing communication settings or connections.

Caution

▪ Signals are related to the controller’s 0V; the same 0V is used by the power supply.

▪ Always use the appropriate port adapters.

▪ The serial ports are not isolated. If the controller is used with a non-isolated external

device, avoid potential voltage that exceeds ± 10V.

Serial Communications

This series comprises 2 RJ-11-type serial ports and a CANbus port.

COM 1 is RS232 only. COM 2 may be set to either RS232 or RS485 via jumper as described on

page 9. By default, the port is set to RS232.

Use RS232 to download programs from a PC, and to communicate with serial devices and

applications, such as SCADA.

Use RS485 to create a multi-drop network containing up to 32 devices.

Pinouts

The pinouts below show the signals sent from the controller to the PC.

To connect a PC to a port that is set to RS485, remove the RS485 connector, and connect the PC

to the PLC via the programming cable. Note that this is possible only if flow control signals are not

used (which is the standard case).

RS232

RS485**

Controller Port

Pin #

Description

Pin #

Description

Pin #1

DTR signal

A signal (+)

0V reference

(RS232 signal)

TXD signal

(RS232 signal)

RXD signal

(RS232 signal)

0V reference

(RS232 signal)

DSR signal

B signal (-)

*Standard programming cables do not provide connection points for pins 1 and 6.

** When a port is adapted to RS485, Pin 1 (DTR) is used for signal A, and Pin 6 (DSR) signal

is used for signal B.

Installation Guide

Unitronics

RS232 to RS485: Changing Jumper Settings

The port is set to RS232 by factory default.

To change the settings, first remove the Snap-in I/O Module, if one is installed, and then set the

jumpers according to the following table.

▪ Before you begin, touch a grounded object to discharge any electrostatic charge.

▪ Before removing a Snap-in I/O Module or opening the controller, you must turn off the power.

RS232/RS485 Jumper Settings

Jumper

RS232*

RS485

Termination

*Default factory setting.

Removing a Snap-in I/O Module

1. Locate the four buttons on the sides of the controller, two on either side.

2. Press the buttons and hold them down to open the locking mechanism.

3. Gently rock the module from side to side, easing the module from the controller.

Re-installing a Snap-in I/O Module

1. Line the circular guidelines on the controller up with the guidelines on the Snap-in I/O Module as

shown below.

2 Apply even pressure on all 4 corners until you hear a distinct ‘click’. The module is now installed.

Check that all sides and corners are correctly aligned.

Vision™ OPLC™ V530-53-B20B

Unitronics

CANbus

Power Supply +

Circuit

protection

device

121

terminating

resistor



121

terminating

resistor



These controllers comprise a CANbus port. Use

this to create a decentralized control network

using one of the following CAN protocols:

▪ CANopen: 127 controllers or external

devices

▪ CANLayer 2

▪ Unitronics’ proprietary UniCAN: 60

controllers, (512 data bytes per scan)

The CANbus port is galvanically isolated.

CANbus Wiring

Use twisted-pair cable. DeviceNet® thick

shielded twisted pair cable is recommended.

Network terminators: These are supplied with the

controller. Place terminators at each end of the

CANbus network.

Resistance must be set to 1%, 121Ω, 1/4W.

Connect ground signal to the earth at only one

point, near the power supply.

The network power supply need not be at the

end of the network

CANbus Connector

Installation Guide

Unitronics

Technical Specifications

Power Supply

Input voltage

12VDC or 24VDC

Permissible range

10.2VDC to 28.8VDC with less than 10% ripple

Max. current consumption

12VDC

24VDC

470mA

230mA

Typical power consumption

5.1W

Battery

Back-up

7 years typical at 25°C, battery back-up for RTC and system data,

including variable data

Replacement

Yes, without opening the controller.

Graphic Display Screen

LCD Type

Graphic, monochrome black and white, FSTN

Display resolution, pixels

320x240 (QVGA)

Viewing area

5.7"

Touchscreen

Resistive, analog

Screen contrast

Via software (Store value to SI 7)

Refer to VisiLogic Help topic

Setting LCD Contrast.

Program

Application memory

1000K

Operand type

Quantity

Symbol

Value

Memory Bits

4096

Bit (coil)

Memory Integers

2048

16-bit

Long Integers

256

32-bit

Double Word

32-bit unsigned

Memory Floats

32-bit

Timers

192

32-bit

Counters

16-bit

Data Tables

120K (dynamic)/ 192K (static)

HMI displays

Up to 255

Program scan time

30μsec per 1K of typical application

Communication

Serial Ports

2. See Note

RS232

Galvanic isolation

Voltage limits

20V

Baud rate range

COM1

COM2

300 to 57600 bps

300 to 115200 bps

Cable length

Up to 15m (50‘)

RS485

Galvanic isolation

Vision™ OPLC™ V530-53-B20B

Unitronics

Voltage limits

−7 to +12V

Baud rates

300 to 115200 bps

Nodes

Up to 32

Cable type

Shielded twisted pair, in compliance with EIA RS485

Cable length

Up to 1200m (4000’)

CANbus port

Nodes

CANopen

Unitronics’ CANbus protocols

127

Power requirements

24VDC (±4%), 40mA max. per unit

Galvanic isolation

Yes, between CANbus and controller

Cable length/baud rate

25 m

100 m

250 m

500 m

1000 m*

1 Mbit/s

500 Kbit/s

250 Kbit/s

125 Kbit/s

100 Kbit/s

50 Kbit/s

20 Kbit/s

* If you require cable lengths over 500

meters, contact technical support.

Optional port

User may install an additional port, available by separate order.

Available port types are: RS232/RS485, and Ethernet.

Notes:

COM 1 supports RS232 only.

COM 2 may be set to either RS232/RS485 according to jumper settings as shown in the product’s

Installation Guide. Factory setting: RS232.

I/Os

Via module

Number of I/Os and types vary according to module. Supports up to

171 digital, high-speed, and analog I/Os.

Snap-in I/O modules

Plugs into rear port; provides an on-board I/O configuration.

Expansion modules

Via adapter, use up to 8 I/O Expansion Modules comprising up to 128

additional I/Os. Number of I/Os and types vary according to module.

Dimensions

Size

197X146.6X68.5mm "7.75 ) X "75.7 X2.7")

Weight

750g (26.5 oz)

Mounting

Panel-mounting

Via brackets

Environment

Inside cabinet

IP20 / NEMA1 (case)

Panel mounted

IP65 / NEMA4X (front panel)

Operational temperature

0 to 50ºC (32 to 122ºF)

Storage temperature

-20 to 60ºC (-4 to 140ºF)

Relative Humidity (RH)

5% to 95% (non-condensing)

Installation Guide

Unitronics

The information in this document reflects products at the date of printing. Unitronics reserves the right, subject to all applicable laws, at any time, at its sole

discretion, and without notice, to discontinue or change the features, designs, materials and other specifications of its products, and to either permanently or

temporarily withdraw any of the forgoing from the market.

All information in this document is provided "as is" without warranty of any kind, either expressed or implied, including but not limited to any implied warranties of

merchantability, fitness for a particular purpose, or non-infringement. Unitronics assumes no responsibility for errors or omissions in the information presented in

this document. In no event shall Unitronics be liable for any special, incidental, indirect or consequential damages of any kind, or any damages whatsoever arising

out of or in connection with the use or performance of this information.

The tradenames, trademarks, logos and service marks presented in this document, including their design, are the property of Unitronics (1989) (R"G) Ltd. or other

third parties and you are not permitted to use them without the prior written consent of Unitronics or such third party as may own them

UG_V530.pdf 07/22