Dodge DSV1 Manuel utilisateur

Dodge
Marque
Dodge
Modèle
DSV1
Taper
Manuel utilisateur
STEP 5
Begin activation
Press the silicone button
located on the sensor to begin
activation. The LED light will
blink three times.
STEP 6
Assign sensor to asset
On the asset page, select your
new asset created in step 3.
Select “Commission sensor” on
the asset properties page.
Find your sensor serial number
from the list.
If desired, name the sensor
position, then select “Yes,
commission”.
STEP 7
Installation complete
After completing the installation
process, the application should
function properly. If there are
any problems, please contact
support at engineering@
support.dodgeindustrial.com.
OPTIFY™ Sensor
Model: DSV1
Installation Instructions
Review these instructions in their
entirety before attempting to
install your OPTIFY Sensor.
Getting Started
Necessary equipment:
Items included in the OPTIFY
Sensor kit:
• OPTIFY Sensor
• Installation tool
• Rubber cover (optional)
Additional items (required):
• Smartphone
• Computer
Additional items (optional):
• Sensor adapter
• Gloves
• Clean soft cloth
• Torque wrench
• 7/8" (22mm) wrench
• 7/16" (11mm) socket
• Socket wrench
STEP 1
Install OPTIFY application
STEP 2
Create an OPTIFY account
using the desktop or mobile
application, then create or join
a plant.
dodgeoptify.com
STEP 3
Create an asset
Log in to the OPTIFY application
with the account created in step 2.
Select “Assets,” then add a new
asset with the “add” button.
Fill in the required asset details:
• Asset name
• Nominal speed
• Part number
Select “Create Asset”.
STEP 4
Mount sensor
Step 4.1
Clean surface to be free of dirt
and debris.
Step 4.2
Find a grease tting, oil plug,
or any other threaded hole that
will accept either the sensor or
sensor adapter.
Optional: Bearing
Locate a grease tting on the
30° face of the bearing and
remove plug.
Optional: Gearing
If being mounted to a gear
reducer, locate the OPTIFY
Sensor adapter and remove
the red push-in plug.
Step 4.3
Thread sensor by hand and
tighten using the installation
tool. If desired, tighten sensor
using a torque wrench, applying
7-12 lbs-in (0.8-1.4Nm).
Specic conditions of use for
this application are as follows:
1. The ambient temperature range
of the sensor is -30°C to 105°C.
The installer is responsible
for ensuring that the sensor is
used between these limits. The
assessment of the sensor’s
functionality and its role in
stopping the bearing in the
event of bearing failure is not
implied by the certication,
which is related to its hazardous
area compliance only.
La plage de température
ambiante du capteur est de
-30°C à 105°C. L’installateur
est responsable de s’assurer
que le capteur est utilisé entre
ces limites. L’évaluation de
la fonctionnalité du capteur
et de son rôle dans l’arrêt du
roulement en cas de défaillance
du roulement n’est pas
impliquée par la certication,
qui concerne uniquement
sa conformité aux zones
dangereuses.
2. Under extreme
circumstances, the non-
metallic cap may generate
an ignition-capable level
of electrostatic charge.
Therefore, the sensor
shall not be installed in a
location where the external
conditions are conducive to
the build-up of electrostatic
charge. In addition, the
equipment shall only be
cleaned with a damp cloth,
and the metallic base of the
sensor shall be eectively
connected to earthed metal
when installed.
Dans des circonstances
extrêmes, le capuchon
non métallique peut
générer un niveau de
charge électrostatique
pouvant s’enammer. Par
conséquent, le capteur ne
doit pas être installé dans
un endroit où les conditions
extérieures sont propices à
l’accumulation de charges
électrostatiques. De plus,
l’équipement ne doit
être nettoyé qu’avec un
chion humide et la base
métallique du capteur doit
être eectivement reliée au
métal mis à la terre lorsqu’il
est installé.
®
CASTING TOLERANCE PER S249
SURFACE FINISH: 125 µin
TIME & DATE:
DRAWING NO:
A
02/08/2023
DESCRIPTION:
MAT'L DESC:
MODEL NO:BY:
BREAK ALL SHARP EDGES .005-.015
VERSION:
MACHINE TOLERANCE PER S022
F
USMIKUN1
REV:
06
750000
750000-3
REV. DESC:
FABRICATION TOLERANCE PER S356
200003482 DIMENSION TOLERANCE, ETC.
UNLESS OTHERWISE SPECIFIED:
TREATMENT:
MAT'L PART NO:
DODGE OPTIFY SENSOR - FULL MARKING
UPDATED LABEL INFO & NOTES
TDR: SHEET NUMBER:
WEIGHT:
1
PAPER SIZE:
1 OF
TITLE BLOCK: MPT-A2
NOTE(S):
1) LAYOUT OF INFORMATION MAY VARY, PROVIDED CONTENT IS IDENTICAL
2) CE, HEX, EX, CSA AND UKCA MARKS TO BE 5MM HIGH MINIMUM
3) MARKING TO BE ETCHED TO STAINLESS STEEL COMPONENT IDENTIFIED IN 750000
4) REPLACE "YYYY" AFTER "MFG:" WITH CURRENT YEAR OF MANUFACTURING.
5) WEEE WHEELIE BIN 7MM HIGH MINIMUM
NOTE: This sensor is intended for application in hazardous location, typical marking shown below.
To manage your registered
assets, visit OPTIFY:
dodgeoptify.com
MN7000_OPTIFY Sensor_02.23.indd 1MN7000_OPTIFY Sensor_02.23.indd 1 2/9/2023 1:12:09 PM2/9/2023 1:12:09 PM
NOTE: These instructions
must be read thoroughly before
installation or operation. This
instruction manual was accurate
at the time of printing. Please
see dodgeindustrial.com for
updated instruction manuals.
CAUTION: The sensor should
be installed by technically
qualied personnel. Failure
to install the sensor in
compliance with applicable
codes and regulation and
according to the manufacturer’s
recommendations may result in
unsatisfactory performance or
equipment failure, and may void
the sensor warranty.
WARNING: Only qualied
individuals who are familiar with
appropriate national codes,
local codes and sound practices
should install, repair or modify
mounted bearings and/or related
accessories. Installation should
conform to appropriate codes
and practices. Failure to follow
these instructions could
result in serious personal injury,
death and/or property damage.
WARNING: To ensure the drive
is not unexpectedly started, turn
o and lock-out or tag
power
source before proceeding
.
Failure to observe these
precautions could result in bodily
injury.
WARNING: Because of the
possible danger to person(s) or
property from accidents which
may result from the improper
use of products, it is important
that correct procedures be
followed. Products must
be used in accordance with
the engineering information
specied in the catalog. Proper
installation, maintenance and
operation procedures must
be observed. The instructions
in the instruction manuals
must be followed. Inspections
should be made as necessary
to assure safe operation under
prevailing conditions. Proper
guards and other suitable
safety devices or procedures as
may be desirable or as may be
specied in safety codes should
be provided, and are neither
provided by Dodge nor are the
responsibility of Dodge. This unit
and its associated equipment
must be installed, adjusted
and maintained by qualied
personnel who are familiar with
the construction and operation of
all equipment in the system and
the potential hazards involved.
When risk to persons or property
may be involved, a holding device
must be an integral part of the
driven equipment beyond the
speed reducer output shaft.
WARNING: Batteries inside.
Fire or explosion may result
if exposed to heat. Do not
disassemble, incinerate, or heat
above +125°C (+257°F).
Piles à l’intérieur. Un incendie
ou une explosion peut survenir
en cas d’exposition à la chaleur.
Ne pas démonter, incinérer ou
chauer au-dessus de +125°C
(+257°F).
Dodge Industrial, Inc.
1061 Holland Road
Simpsonville, SC 29681
+1 864 297 4800
All Rights Reserved. Printed in USA.
MN7000 02/23
© DODGE INDUSTRIAL, INC.
AN RBC BEARINGS COMPANY
Industry Canada Statement:
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables auz appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilsateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouilage est
susceptible d’en compromettre le fonctionnement.
Country of Origin: Japan
HS Code (HTS): 9031.80.8085
WEEE EU Directive 2012/19/EU
Products that are marked with the crossed-out wheeled bin symbol
as shown here; shall be handled by applying following information:
• The crossed-out wheeled bin symbol
on the product(s) and/or accompanying
documents means that used electrical and
electronic equipment (WEEE) should not
be mixed with general household waste.
• For professional users in the European
Union, please contact your dealer or
supplier for more information on how
to discard electrical and electronic
equipment (EEE).
CAUTION: Mounted bearing
surface temperature hazard. The
external surface of a mounted
bearing may reach temperatures
which can cause discomfort,
burns or injury to individuals.
FCC Compliance Statement:
CAUTION: Changes or
modications not expressly
approved could void your
authority to use this equipment.
This device complies with Part
15 of the FCC Rules. Operation
to the following two conditions:
(1) This device may not cause
harmful interference and (2)
this device must accept any
interference received, including
interference that may cause
undesired operation.
NOTE: Frequency band(s)
in which the radio equipment
operates: 2402 MHz–2480 MHz.
Maximum radio-frequency power
transmitted in the frequency
band(s) in which the radio
equipment operates: 0dBm.
Specications:
• Intrinsically safe, stand-alone
battery powered device
(3.6Vdc nominal)
• Low energy Bluetooth (BLE)
communications
• 2400-2483.5 MHz
• BW = 2MHz
• EIRP ≤ 2dBm
• GFSK modulation
• Antenna gain = 0dBi
Scan for translated versions:
info.dodgeindustrial.com/translations
MN7000_OPTIFY Sensor_02.23.indd 2MN7000_OPTIFY Sensor_02.23.indd 2 2/9/2023 1:12:09 PM2/9/2023 1:12:09 PM
  • Page 1 1
  • Page 2 2

Dodge DSV1 Manuel utilisateur

Dodge
Marque
Dodge
Modèle
DSV1
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents