Dyson DBWIFIBLE05 Wireless Local Area Network Module Manuel utilisateur

DBWIFIBLE05 Wireless Local Area Network Module
Dyson
Marque
Dyson
Modèle
DBWIFIBLE05 Wireless Local Area Network Module
Taper
Manuel utilisateur
1 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
Project Name: DBWIFIBLE05
Author: Wistron NeWeb Corporation
Revision: 0.2
Revision Date: 2022/06/13
2 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
Revision History
REV
Author
Summary Changes
0.1
Jim Chuang
SGA(ES1) Draft Product Spec
0.2
Jim Chuang
SGB(ES2) Draft Product Spec
3 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
© Wistron NeWeb Corporation
THIS DOCUMENT AND THE INFORMATION CONTAINED HEREIN IS PROPRIETARY AND IS THE EXCLUSIVE
PROPERTY OF WNC AND SHALL NOT BE DISTRIBUTED, REPRODUCED, OR DISCLOSED IN WHOLE OR IN
PART WITHOUT PRIOR WRITTEN PERMISSION FROM WNC.
LIMITATION OF LIABILITY
THIS DOCUMENT AND THE INFORMATION CONTAINED HEREIN IS PURELY FOR DESIGN REFERENCE AND
SUBJECT TO REVISION BY WNC AT ANY TIME. NOTHING IN THIS DOCUMENT SHALL BE CONSTRUED AS
GRANTING ANY WARRANTY OR RIGHT TO USE THE MATERIAL CONTAINED HEREIN WITHOUT WNC’S
PRIOR EXPRESS WRITTEN CONSENT. WNC SHALL NOT BE LIABLE FOR ANY USE, APPLICATION OR
DEVELOPMENT DERIVED FROM THE MATERIAL WITHOUT SUCH PRIOR EXPRESS WRITTEN CONSENT.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Country Code selection feature to be disabled for products marketed to the US/CANADA
4 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
Integration instructions for host product manufacturers
Applicable FCC rules to module
FCC Part 15.247
Summarize the specific operational use conditions
The module is must be installed in mobile device.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna
3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G
band
by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding
to Regulatory Domain change.
As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining
a separate FCC authorization. The OEM integrator has to be aware not to provide information to the end
user regarding how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Limited module procedures
Not applicable
Trace antenna designs
Not applicable
RF exposure considerations
20 cm separation distance and co-located issue shall be met as mentioned in “Summarize the specific
operational use conditions”.
Product manufacturer shall provide below text in end-product manual
“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.”
Antennas
Brand name
Model name
Antenna type
Antenna gain
Antenna connector
Dyson
ANT2_1370X950
PIFA
2400~2483.5MHz: 2.12dBi
5150~5250MHz: 2.59dBi
5250~5350MHz: 2.62dBi
5470~5725MHz: 2.79dBi
5725~5850MHz: 3.44dBi
No
Changing the antenna type, gain, including the trace design while installing the host may requires to be
recertified via FCC class change procedure
5 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
Label and Compliance Information
Product manufacturers need to provide a physical or e-label stating
“Contains FCC ID: QVHDBWIFIBLE05” with finished product
Information on Test Modes and Additional Testing Requirements
Test tool: Tera Term, V4.89 shall be used to set the module to transmit continuously.
Additional Testing, Part 15 Subpart B Disclaimer
The module is only FCC authorized for the specific rule parts listed on the grant, and that the host
product manufacturer is responsible for compliance to any other FCC rules that apply to the host not
covered by the modular transmitter grant of certification. The final host product still requires Part 15
Subpart B compliance testing with the modular transmitter installed
6 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
Industry Canada statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause undesired operation
of the device
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Caution:
(i) the device for operation in the band 5150–5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) for devices with detachable antenna(s), the maximum antenna gain permitted
for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still
complies with the e.i.r.p. limit;
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted
for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the
e.i.r.p. limits as appropriate; and
Operations in the 5.25-5.35GHz band are restricted to indoor usage only.
Avertissement:
(i) les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont
réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne
permis pour les dispositifs utilisant les bandes de 5 250 à 5 350 MHz et de 5 470 à 5 725 MHz doit
être conforme à la limite de la p.i.r.e;
(iii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne permis (pour les
dispositifs utilisant la bande de 5 725 à 5 850 MHz) doit être conforme à la limite de la p.i.r.e.
spécifiée, selon le cas;
Les opérations dans la bande de 5.25-5.35GHz sont limités à un usage intérieur seulement.
7 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme Canada limites d'exposition aux radiations dans un environnement non
contrôlé. Cet équipement doit être installé et utilisé à distance minimum de 20cm entre le radiateur et
votre corps.
This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 1 condition above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes:
1) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 1 condition ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas
nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour
toutes exigences de conformité supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location
with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can
not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-
evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations
d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada
n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces
circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et
l'obtention d'une autorisation distincte au Canada.
End Product Labeling
The final end product must be labeled in a visible area with the following: “Contains IC: 7986A-
DBWIFIBLE05”.
8 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
Plaque signalétique du produit final
Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC:
7986A-DBWIFIBLE05".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install
or remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la
façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre
ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et
avertissements comme indiqué dans ce manuel.
Taiwan 警語:
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更
原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，
應立即停用，並改善至無干擾時方得繼續使用。
前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及
醫療用電波輻射性電機設備之干擾。
無線資訊傳輸設備避免影響附近雷達系統之操作。
系統廠商應於平台上標示「本產品內含射頻模組: CCAFXXLPXXXXTX)」字樣
9 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
Contents
Revision History ................................................................................................................................ 2
Contents ........................................................................................................................................... 9
1. Introduction ........................................................................................................................... 10
1.1. Features .................................................................................................................................10
1.2. Block Diagram ........................................................................................................................10
2. Electrical Specifications .......................................................................................................... 11
2.1. Interface pin assignments ......................................................................................................11
2.1.1. Connectors Diagram for module................................................................................11
2.1.2. Pin Assignments & Circuit of connectors for module ................................................12
2.2. Absolute Maximum Ratings ...................................................................................................13
2.3. Recommend Operating Conditions .......................................................................................13
2.4. Connectivity ...........................................................................................................................14
2.5. Digital logic characteristics (3.3V I/O operation) ...................................................................15
3. RF Specifications .................................................................................................................... 16
3.1. RF connections .......................................................................................................................16
3.1.1. WIFI Typical RF performance at Antenna Connector at 25oC ....................................16
3.1.2. BT-Low Energy RF performance at Antenna Connector at 25OC ...............................16
4. Antenna Performance ............................................................................................................ 17
4.1. Module antenna Efficiency/Peak gain/S Parameters ............................................................17
4.2. Module antenna 2D radiation pattern ..................................................................................18
5. Mechanical and Environmental Specifications ......................................................................... 19
5.1. PCBA form factor ...................................................................................................................19
5.2. Module Antenna Clearance and keep-out area ....................................................................19
5.3. Labeling ..................................................................................................................................20
5.4. Moisture Sensitivity Level ......................................................................................................22
5.5. BOM .......................................................................................................................................22
6. Regulatory and Industry Approvals ......................................................................................... 23
6.1. Certification Country .............................................................................................................23
7. Safety Recommendation......................................................................................................... 24
8. Packaging ............................................................................................................................... 25
10 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
1. Introduction
DBWIFIBLE05 is a wireless local area network (WLAN), Bluetooth (BT) Low Energy combo module to
support 2.4G/5G IEEE 802.11a/ b/g/n WLAN standards, BLE 5.0 and below. It enables seamless
integration of WLAN/BT Low Energy technology with powerful embedded CPU.
1.1. Features
◼ ARM Cortex-M33.
◼ Wi-Fi Support IEEE 802.11a/b/g/n 2.4G/5G Band, and 1x1 20 MHz bandwidth only.
◼ Bluetooth Low Energy (BLE) compliant to the SIG v5 specification.
◼ Single 3.3V supply.
◼ Internal 1 on-board antennas for WIFI and BLE and 1 optional external antenna connector.
◼ GPIO to support the peripherals interfaces:
• 10-pins(J2) SWD connector
• 8-pins(J1) system controller connector
• 4-pins(J3) debug UART connector
1.2. Block Diagram
11 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
2. Electrical Specifications
2.1. Interface pin assignments
2.1.1. Connectors Diagram for module
There is a system control connector (J1) for power supply and SPI interface.
J1- wire to board connector
Connector Location
12 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
2.1.2. Pin Assignments & Circuit of connectors for module
Table 1. connectors Interface Family
13 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
2.2. Absolute Maximum Ratings
Signal
Description
Max.
Unit
3.3V_IN
3.3V Power Supply Input for Pin8 of J1
3.465
V
VIH
GPIO pull high Voltage
3.3V_IN + 0.3
V
TA
Operating Temperature
65
oC
2.3. Recommend Operating Conditions
Signal
Description
Min.
Typ.
Max.
Unit
3.3V_IN
3.3V Power Supply Input
3.135 (-5%)
3.3
3.465 (+5%)
V
VIH
GPIO pull high Voltage
3.3V_IN x 0.625
3.3V_IN + 0.3
V
VIL
GPIO pull low Voltage
-0.3
3.3V_IN x 0.25
V
TA
Operating Temperature
-5
25
65
oC
14 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
2.4. Connectivity
The connectivity support by module ( SGB ) include:
◼ J1 – System Controller Connector (CVILUX CI4008M1VR0-NH)
Pin
Signal Name
1
Handshake_I
2
SPI MOSI
3
SPI MISO
4
SPI CLK
5
SPI CS
6
SYSRST_B
7
GND
8
3.3V_IN
◼ J2–SWD Program/Debug Connector (SAMTEC FTSH-105-01-F-DV)
Pin
Signal Name
1
3.3V_IN
2
SWD_DATA
3
GND
4
SWD_CLK
5
GND
6
NC
7
NC
8
PAD_GPIO_B_12
9
GND
10
SYSRST_B
◼ J3 – UART Debug Connector (CVILUX CI1104M1VR0-NH)
Pin
Signal Name
1
UART_ TXD
2
UART_ RXD
3
GND
4
3.3V_IN
15 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
2.5. Digital logic characteristics (3.3V I/O operation)
Signal
Description
Min.
Typ.
Max.
Unit
VIH
Input-High Voltage
-0.3
3.3V_IN x 0.25
V
VIL
Input-Low Voltage
3.3V_IN x 0.625
3.3V_IN + 0.3
V
VOH
Output-High Voltage
-0.3
-0.45
V
VOL
Output-Low Voltage
3.3V_IN – 0.45
-
3.3V_IN + 0.3
V
16 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
3. RF Specifications
3.1. RF connections
3.1.1. WIFI Typical RF performance at Antenna Connector at 25oC
2.4GHz
Standard
Modulation
Index
TX Target Power
RX Sensitivity
Unit
802.11b
BPSK
1Mbps
16
-95 +/-3
dBm
CCK
11Mbps
16
-87 +/-3
dBm
802.11g
BPSK
6Mbps
16
-92 +/-3
dBm
64 QAM
54Mbps
16
-75+/-3
dBm
802.11n
(HT20)
BPSK
MCS0
16
-89 +/-3
dBm
64 QAM
MCS7
16
-71+/-3
dBm
5GHz
Standard
Modulation
Index
TX Target Power
RX Sensitivity
Unit
802.11a
BPSK
6Mbps
13
-92 +/-3
dBm
64 QAM
54Mbps
13
-74 +/-3
dBm
802.11n
(HT20)
BPSK
MCS0
11
-89 +/-3
dBm
64 QAM
MCS7
11
-71 +/-3
dBm
3.1.2. BT-Low Energy RF performance at Antenna Connector at 25OC
Test Item
Description
Typical
Unit
Maximum TX power
1Mbps
4
dBm
TX Power under low TX
1Mbps
-26 +/-4
dBm
RX Sensitivity
1Mbps
-94 +/-4
dBm
The data shown in the table is a preliminary pre-test data at 25OC at RF In-line connector, subject to
change after the measurement.
17 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
4. Antenna Performance
4.1. Module antenna Efficiency/Peak gain/S Parameters
18 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
4.2. Module antenna 2D radiation pattern
19 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
5. Mechanical and Environmental Specifications
5.1. PCBA form factor
5.2. Module Antenna Clearance and keep-out area
20 / 25
□ Normal □ Internal Use Confidential □ Restricted Confidential
DBWIFIBLE05 User Manual
5.3. Labeling
5.3.1 Barcode content
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25

Dyson DBWIFIBLE05 Wireless Local Area Network Module Manuel utilisateur

DBWIFIBLE05 Wireless Local Area Network Module
Dyson
Marque
Dyson
Modèle
DBWIFIBLE05 Wireless Local Area Network Module
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents