ROSIERES RFC3O3379IN WIFI Manuel utilisateur

Catégorie
Fours
Taper
Manuel utilisateur

Ce manuel convient également à

USER INSTRUCTIONS
OVENS
NOTICE D'EMPLOI ET D'INSTALLATION
DES FOURS ENCASTRABLES
EN
FR
02
19
USINES DE ROSIÈRES - 30, rue Y. LACELLE - Rosières - 18400 - Lunery - France
Safety Indications
EN 02
When you open the door after you have finished cooking, a few drops
of water may come out of the door. It depends on the type of food you
have cooked.
• During cooking, moisture may condense inside the oven cavity or on
the glass of the door. This is a normal condition. To reduce this effect,
wait 10-15 minutes after turning on the power before putting food
inside the oven. ln any case, the condensation disappears when the
oven reaches the cooking temperature.
Cook the vegetables in a container with a lid instead of an open tray.
Avoid leaving food inside the oven after cooking for more than 15/20
minutes.
WARNING: the appliance and accessible parts become hot during use.
Be careful not to touch any hot parts.
WARNING: the accessible parts can become hot when the grill is in
use. Children should be kept at a safe distance.
WARNING: ensure that the appliance is switched off before replacing
the bulb, to avoid the possibility of electric shocks.
WARNING: in order to avoid any danger caused by the accidental
resetting of the thermal interruption device, the appliance should not
be powered by an external switching device, such as a timer, or be
connected to a circuit that is regularly switched on and off.
Children under 8 should be kept at a safe distance from the appliance
if not continuously supervised.
Children should not play with the appliance.
The appliance can be used by those aged 8 or over and by those with
limited physical, sensorial or mental capacities, without experience or
knowledge of the product, only if supervised or provided with
instruction as to the operation of the appliance, in a safe way with
awareness of the possible risks.
Cleaning and maintenance should not be carried out by unsupervised
children.
Do not use rough or abrasive materials or sharp metal scrapers to
EN 03
clean the oven door glasses, as they can scratch the surface and cause
the glass to shatter.
The oven must be switched off before removing the removable parts.
After cleaning, reassemble them according the instructions.
Only use the meat probe recommended for this oven.
Do not use a steam cleaner for cleaning operations.
Connect a plug to the supply cable that is able to bear the voltage,
current and load indicated on the tag and having the earth contact. The
socket must be suitable for the load indicated on the tag and must have
ground contact connected and in operation. The earth conductor is
yellow-green in colour. This operation should be carried out by a
suitably qualified professional. ln case of incompatibility between the
socket and the appliance plug, ask a qualified electrician to substitute
the socket with another suitable type. The plug and the socket must be
conformed to the current norms of the installation country. Connection
to the power source can also be made by placing an omnipolar breaker
between the appliance and the power source that can bear the
maximum connected load and that is in line with current legislation.
The yellow-green earth cable should not be interrupted by the breaker.
The socket or omnipolar breaker used for the connection should be
easily accessible when the appliance is installed.
• The disconnection may be achieved by having the plug accessible or
by incorporating a switch in the fixed wiring in accordance with the
wiring rules.
lf the power cable is damaged, it should be substituted with a cable or
special bundle available from the manufacturer or by contacting the
customer service department. The type of power cable must be
H05V2V2-F. This operation should be carried out by a suitably qualified
professional. The earth conductor (yellow-green) must be
approximately 10 mm longer than the other conductors. For any
repairs, refer only to the Customer Care Department and request the
use of original spare parts.
Failure to comply with the above can compromise the safety of the
appliance and invalidate the guarantee.
Any excess of spilled material should be removed before cleaning.
A long power supply failure during an occurring cooking phase may
cause a malfunction of the monitor. ln this case contact customer
service.
The appliance must not be installed behind a decorative door in order
to avoid overheating.
• When you place the shelf inside, make sure that the stop is directed
upwards and in the back of the cavity. The shelf must be inserted
completely into the cavity.
WARNING: Do not line the oven walls with aluminium foil or single-use
protection available from stores. Aluminium foil or any other
protection, in direct contact with the hot enamel, risk melting and
deteriorating the enamel of the insides.
WARNING: Never remove the oven door seal.
CAUTION: Do not refill the cavity bottom with water during cooking or
when the oven is hot.
No additional operation/setting is required in order to operate the
appliance at the rated frequencies.
EN 04
Summary
EN 05
General Instructions
6
1.1 Safety indications
1.2 Electrical safety
1.3 Recommendations
1.4 Installation
1.5 Waste management
1.6 Declaration of compliance
2.1 Overview
2.2 Accessories
2.3 First use
Product Description
8
3.1 Display description
3.2 Cooking modes
Use of the Oven
9
4.1 General notes on cleaning
4.2 Maintenance
• Instruction for removal and cleaning
of the side racks
• Removal of the oven window
• Removal and cleaning of the glass
door
• Changing the bulb
Oven Cleaning and Maintenance
16
5.1 F.A.Q.
Troubleshooting
18
1. General Instructions
We thank you for choosing one of our products. For the
best results with your oven, you should read this
manual carefully and retain it for future reference.
Before installing the oven, take note of the serial
number so that you can give it to customer service staff
if any repairs are required. Having removed the oven
from its packaging, check that it has not been damaged
during transportation. If you have doubts, do not use
the oven and refer to a qualified technician for advice.
Keep all of the packaging material (plastic bags,
polystyrene, nails) out of the reach of children. When
the oven is switched on for the first time, strong
smelling smoke can develop, which is caused by the glue on the insulation panels surrounding the oven
heating for the first time. This is absolutely normal and, if it occurs, you should wait for the smoke to
dissipate before putting food in the oven. The manufacturer accepts no responsibility in cases where
the instructions contained in this document are not observed.
NOTE: the oven functions, properties and accessories cited in this manual will vary, depending on the
model you have purchased.
1.1 Safety Indications
Only use the oven for its intended purpose, that is only for the cooking of foods; any other use, for
example as a heat source, is considered improper and therefore dangerous. The manufacturer cannot
be held responsible for any damage resulting from improper, incorrect or unreasonable usage.
The use of any electrical appliance implies the observance of some fundamental rules:
- do not pull on the power cable to disconnect the plug from the socket;
- do not touch the appliance with wet or damp hands or feet;
- in general the use of adaptors, multiple sockets and extension cables is not recommended;
- in case of malfunction and/or poor operation, switch off the appliance and do not tamper with it.
1.2 Electrical Safety
ENSURE THAT AN ELECTRICIAN OR QUALIFIED TECHNICIAN MAKES THE ELECTRICAL CONNECTIONS.
The power supply to which the oven is connected must conform with the laws in force in the country of
installation. The manufacturer accepts no responsibility for any damage caused by the failure to observe
these instructions. The oven must be connected to an electrical supply with an earthed wall outlet or a
disconnector with multiple poles, depending on the laws in force in the country of installation. The
electrical supply should be protected with suitable fuses and the cables used must have a transverse
section that can ensure correct supply to the oven.
CONNECTION
The oven is supplied with a power cable that should only be connected to an electrical supply with 220-
240 Vac 50 Hz power between the phases or between the phase and neutral. Before the oven is
connected to the electrical supply, it is important to check:
- power voltage indicated on the gauge;
- the setting of the disconnector.
The grounding wire connected to the oven's earth terminal must be connected to the earth terminal of
the power supply.
WARNING
Before connecting the oven to the power supply, ask a qualified electrician to check the continuity of the
power supply's earth terminal. The manufacturer accepts no responsibility for any accidents or other
problems caused by failure to connect the oven to the earth terminal or by an earth connection that has
defective continuity.
EN 06
1.3 Recommendations
After each use of the oven, a minimum of cleaning will help keep the oven perfectly clean.
Do not line the oven walls with aluminium foil or single-use protection available from stores. Aluminium
foil or any other protection, in direct contact with the hot enamel, risks melting and deteriorating the
enamel of the insides. In order to prevent excessive dirtying of your oven and the resulting strong
smokey smells, we recommend not using the oven at very high temperature. It is better to extend the
cooking time and lower the temperature a little. In addition to the accessories supplied with the oven,
we advise you only use dishes and baking moulds resistant to very high temperatures.
1.4 Installation
The manufacturers have no obligation to carry this out. If the assistance of the manufacturer is required
to rectify faults arising from incorrect installation, this assistance is not covered by the guarantee. The
installation instructions for professionally qualified personnel must be followed. Incorrect installation
may cause harm or injury to people, animals or belongings. The manufacturer cannot be held
responsible for such harm or injury.
The oven can be located high in a column or under a worktop. Before fixing, you must ensure good
ventilation in the oven space to allow proper circulation of the fresh air required for cooling and
protecting the internal parts. Make the openings specified on last page according to the type of fitting.
NOTE: as the oven could require maintenance work, it is advisable to keep another wall socket available
so that the oven can be connected to this if it is removed from the space in which it is installed. The
power cable must only be substituted by technical service staff or by technicians with equivalent
qualifications.
1.5 Waste management and environmental protection
This appliance is labelled in accordance with European Directive 2012/19/EU regarding electric
and electronic appliances (WEEE). The WEEE contain both polluting substances (that can have
a negative effect on the environment) and base elements (that can be reused). It is important
that the WEEE undergo specific treatments to correctly remove and dispose of the pollutants
and recover all the materials. Individuals can play an important role in ensuring that the WEEE
do not become an environmental problem; it is essential to follow a few basic rules:
- the WEEE should not be treated as domestic waste;
- the WEEE should be taken to dedicated collection areas managed by the town council or a registered
company.
In many countries, domestic collections may be available for large WEEEs. When you buy a new appliance,
the old one can be returned to the vendor who must accept it free of charge as a one-off, as long as the
appliance is of an equivalent type and has the same functions as the purchased appliance.
SAVING AND RESPECTING THE ENVIRONMENT
Where possible, avoid pre-heating the oven and always try to fill it. Open the oven door as infrequently as
possible, because heat from the cavity disperses every time it is opened. For a significant energy saving,
switch off the oven between 5 and 10 minutes before the planned end of the cooking time, and use the
residual heat that the oven continues to generate. Keep the seals clean and in order, to avoid any heat
dispersal outside of the cavity. If you have an electric contract with an hourly tariff, the "delayed cooking"
programme makes energy saving more simple, moving the cooking process to start at the reduced tariff
time slot.
1.6 Declaration of compliance
By placing the mark on the appliance, we are confirming compliance to all relevant European
safety, health and environmental requirements which are applicable in legislation for this product.
Hereby, Candy Hoover Group Srl declares that the radio equipment is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at the following internet
address: www.candy-group.com.
EN 07
2. Product Description
2.1 Overview
1. Control panel
2. Shelf positions
(lateral wire grid if included)
3. Metal grill
4. Drip pan
5. Fan (behind the steel plate)
6. Oven door
2.2 Accessories
Metal grill
2
Drip pan
1
Holds baking trays and plates.
Collects the residues that drip during the cooking
of foods on the grills.
EN 08
Lateral wire grids
3
It located at both sides of the oven cavity. It holds
metal grills and drip pans.
2
3
5
4
6
1
2
3
4
5
6
1
3
4
2
7
8
9
10
1
5
6
2.3 First Use
PRELIMINARY CLEANING
Clean the oven before using for the first time. Wipe over external surfaces with a damp soft cloth. Wash
all accessories and wipe inside the oven with a solution of hot water and washing up liquid. Set the
empty oven to the maximum temperature and leave on for about 1 hour, this will remove any lingering
smells of newness.
EN 09
3. Use of the Oven
3.1 Display description
WARNING : the first operation to carry out after the oven
has been installed or following the interruption of power
supply (this is recognizable the display pulsating and
showing ) is setting the correct time. 12:00 The bottom
right LED flashes at the same time ( ). This is achieved
as follows.
•Set time with buttons."-" "+"
•Push the Menu button or wait 5 seconds than the clock is
setted.
ATTENTION: The oven will only operate setting the clock
1. Thermostat selector knob
2. Thermostat signal lamp
3. End of cooking
4. Cooking time
5. Temperature or clock display
6. LCD display adjustment controls
7. Minute minder
8. Clock setting
9. Wifi signal lamp
10. Function selector knob
EN 10
FUNCTION HOW TO DEACTIVATE WHAT IT DOES WHY IT IS NEEDED HOW TO USE
KEY LOCK
MINUTE
MINDER
COOKING
TIME
END OF
COOKING
•Child Lock function is
activated by touching Set
(+) for a minimum of 5
seco n d s . Fr om t h i s
moment on all other
function are locked and
the display will flash
STOP and preset time
intermittently.
•Child Lock function is
deactivated by touching
touchpad Set (+) again
for a minimum of 5
seco n d s . Fr om t h i s
moment on all functions
are selectable again.
•Push the central button
1 times
•Press the buttons "-"
"+"
to set the required time
•Release all the buttons
•When the set time as
elapsed an audible alarm
is activated (this alarm
will stop on its own,
ho wever it ca n b e
stopped immediately by
pressing the button)
SELECT.
•Sounds an alarm at the
end of the set time.
During the process, the
display shows the
remaining time.
•Allows to use the oven as
al arm c l oc k ( co uld b e
a c t i v a t e d ei t h er wit h
operating the oven or with
out operating the oven)
Push the central button
2 times
Press the buttons "-" or
"+"to set the lenght of
cooking required
Release all buttons
S e t t h e c o o k i n g
function with the oven
function selector
It allows to preset the
cooking time required for
the recipe chosen.
To check how long is left
to run press the SELECT
button 2 Times.
To alter/change the
preset time press SELECT
and "-" "+" buttons.
Push any button to
stop the signal. Push the
central button to return
t o t h e c l o c k
function.
•When the time is elapsed
the oven will switch off
automatically.
Should you wish to stop
cooking earlier either turn
the function selector to 0, or
s e t t i m e t o 0 : 0 0
(SELECT and "-" "+" buttons)
•At the time set, the
oven will switch off. To
switch off manually,
turn the oven function
selector to position O.
•Enables you to set the
end of cooking time
To check the preset
time push the central
button 3 times
•To modify the preset
tim e pre s s b u tto n s
SELECT + "-" "+"
Push the central button
3 t i m e s P r e s s t h e
buttons "-" "+" to set the
time at which you wish
the oven to switch off
•Release the buttons
• S e t t h e c o o k i n g
function with the oven
function selector.
•This function is typically
used with “cooking time”
function.
For example if the dish has
to be cooked for 45 minutes
and needs to be ready by
12:30, simply select the
required function, set the
cooking time to 45 minutes
and the end of cooking time
to 12:30.
•At the end of the cooking
set time, the oven will
switch off automatically and
an audible alarm will ring.
• C o o k i n g w i l l s t a r t
auto m a t i cally at 11:45
(12:30 minus 45 mins) and
will continue until the pre-
set end-of-cooking-time,
when the oven will switch
itself off automatically.
WARNING.
If the END of cooking is
selected without setting the
length of cooking time, the
oven will start cooking
immediately and it will stop
at the END of cooking time
set.
ELETTRONICA ZERO WIFI FUNCTION
For all the details related to the link between app and product, refer to the
Quick Guide.
Wi Fi has two different positions on the cooking selector:
• Wi Fi on: Wi Fi is switched on only if the oven is already enrolled to your
device. In this position the oven will be only controlled by remote.
Wi Fi reset: After leaving the selector on Wi Fi reset for 30, Bluetooth will
switch on and you will be able to enroll the oven to your device within 5.
If the enrollment is successful, the oven will be controlled by remote and
the Wi Fi icon will switch on. If the enrollment is unsuccessful, Wi Fi will
switch off and the oven will be reset.
To proceed with a new enrollment the cooking program selector has to be
turned out from Wi Fi reset position and moved again on it.
Note: Install the App on your device before starting enrolling
Note: The device where the App is installed must have Bluetooth activated
Note: For both Wi Fi positions, the touch buttons do not work.
Note: It is important to establish a good Wi-Fi signal strength between the
home router and the appliance. When the oven is trying to connect to
router the icon will blink 3” on and 1off, when it is already connected the
icon will switch on.
1. Program selection / 2. Program duration / 3. Cooking start setting / 4- Dedicated recipes selection
/ 5. Offline and vocal assistant / 6. Tips, suggestions and online user manual
1 2
3 4
6
5
ROSIERES E-PICURIEN:
For detailed information on HOW TO CONNECT your E-picurien appliance
and HOW TO USE IT effectively, go to www.rosieresepicurien.com.
EN 11
WIRELESS PARAMETERS
Bluetooth v4.2
2,412 GHz. – 2,484 GHz
Basic data rate:
RF Transmit Power (Typ):
+4 dBm
Enhanced data rate:
RF Transmit Power (Typ):
+2 dBm
BLE:
RF Transmit Power (Typ):
+7.5 dBm
802.11 b/g/n
2,412 GHz. – 2,484 GHz
802.11b. DSSS 1 Mbps=
+19.5 dBm
802.11b. CCK 11 Mbps=
+18.5 dBm
802.11g. OFDM 54 Mbps=
+18.5 dBm
802.11n. MCS7=
+14 dBm
802.11b =1024 bytes,
-80 dBm
802.11g =1024 bytes,
-70 dBm
802.11n =1024 bytes,
-65 dBm
802.11n HT40 =1024 bytes,
-65 dBm
Wireless
Standart
Frequency
Range
Max.
Transmit
Power
Minimum
Receiving
Sensivity
Parameter
Specifications
(Wi-Fi)
Specifications
(Bluetooth)
Basic data rate:
Sensivity@ 0.1% BER:
-98 dBm
Enhanced data rate:
Sensivity@ 001% BER:
-98 dBm
BLE:
Sensivity@ 0.1% BER:
-98 dBm
Product information for networked equipment
power consumption of
the product in networked
st a n d by i f a l l w i re d
n e t w o r k p o r t s a r e
c o n n e c t e d a n d a l l
wireless network ports
are activated:
2,0 W
How to activate wireless
network port:
Starting from an oven that
is not enrolled, putting the
right knob on the Reset
position. Wifi module is
switched on after 30".
If oven is enrolled with WiFi
off, putting the right knob
on WiFi position the WiFi
module is switched on.
H o w t o d e a c t i v a t e
wireless network port:
If oven is enrolled, putting
the right knob on Reset
position the WiFi module
is switched off.
Quick Guide Rosières E-Picurien OVEN -
Enrollment on App
Procedure for devices with Bluetooth 4.0 (or
higher)
IMPORTANT
This quick guide illustrates the steps to follow to
enroll your appliance on the App Rosières E-
Picurien, using a device with Bluetooth 4.0 (or
higher) technology. In this case, the procedure is
simplified and faster (Easy Enrollment).
If you are using a device without Bluetooth
technology (or less than 4.0), please follow the
instructions described on the other side of this
guide.
STEP 1
Mark down the appliance Serial Number.
Mark down the Wi-Fi Name and Password
(WPA/ WEP Key) which are normally placed on the
back of your Wi-Fi router.
NOTES
The frequency of the home Wi-Fi network has to
be set on the 2.4 GHz band. You cannot configure
the appliance if your home network is set to the 5
GHz band.
If you are having trouble locating the WPA/WEP
Password, please contact your Internet Provider.
Please make sure your smartphone is connected
to the same Wi-Fi network and has the Bluetooth
enabled within the “Settings”. Refer to the manual
for more details.
STEP 2
Download the Rosières E-Picurien App from the
Store.
Open the Rosières E-Picurien App and create
your user profile by taping on “Register”. Accept
the privacy policy and fill in the required fields.
NOTES
The App is available for Android (version 4.4 or
higher) and iOS (version 8.0 or higher) devices.
If you already have a Rosières E-Picurien user
profile, you can login using your credentials.
STEP 3
In the homepage, tap on the icon with the three
bars on the top left to enter your profile, then tap
on “REGISTER NEW APPLIANCE” and select the
name of the product that you want to enroll.
STEP 4
Insert the purchase date of your appliance
(DD/MM/YYYY), then tap on “Proceed”.
STEP 5
Insert the 16 digits of the serial number or scan
the QR code on the appliance. Tap on “Next.
Check data correctness of the data and tap on
“Confirm”. Once the system has recognized the
product, tap on “Next”.
STEP 6
On the appliance:
1) Turn the knob to the WI-FI RESET program and
wait 30 seconds.
2) When the Wi-Fi indicator starts blinking quickly,
Bluetooth will come on for 5' and you can proceed
with enrollment within 5 minutes.
In App:
Tap on “Confirm”. Wait for APP to connect to the
appliance.
NOTES
In case of any issue, tap “Retry, making sure you
have enabled Bluetooth on your device
(smartphone / tablet). If the process has not been
completed correctly yet, tap on “Proceed with
Standard Enrollment”.
To ensure correct data transfer, we recommend
you to stay with the device close to the appliance.
STEP 7
Insert the password of your home Wi-Fi
network.
Select the type of password (WEP or WPA), then
tap on “Confirm”.
The enrollment process is now finished.
NOTES
If this is not automatically synchronised by the
App, please insert the name of your home Wi-Fi
network in the first box; pay attention to the
difference between lowercase and uppercase.
IF THE SET UP IS NOT SUCCESSFUL
It's important to establish a good Wi-Fi signal
strength between the home router and the
appliance: low Wi-Fi signal strength would cause
the failure of the final stage of the set up. To assess
if this is the case, start the connection process
again from Step 1; when you get to Step 6, when
you get to Step 6, place your device (smartphone
or tablet) next to the router and search for
“WIFIOVEN-xyzk” net generated by the appliance.
If this does not come up as an option, it means
EN 12
that the router cannot see the appliance. In this
case, we highly recommend you to bring the
router near the appliance (if possible) or contact
your internet provider to purchase a compatible
“Wi-Fi Range Extender” to increase the signal
strenght.
Remote control mode
Turn the program selection knob to the WI-FI
position: the wifi light will turn on and you can
now control the oven remotely.
NOTES
Warning, if the enrolled oven is left on the WI-FI
RESET position for more than 5 minutes, the oven
will be reset and you will have to proceed with a
new enrollment.
Quick Guide Rosières E-Picurien OVEN -
Enrollment on App
Procedure for devices without Bluetooth 4.0 (or
less than 4.0)
IMPORTANT
This quick guide outlines the steps you should
follow to enroll your appliance using the App
Rosières E-Picurien, utilizing a device without
Bluetooth technology. We recommend you to
proceed with a smartphone/tablet equipped with
this technology to make the procedure simpler.
If you are using a device with Bluetooth
technology (or higher than 4.0), please follow the
instructions described on the other side of this
guide.
STEP 1
Make a note of the appliance Serial Number and
Wi-Fi Name and Password (WPA/WEP Key), which
are normally found on the back of your Wi-Fi
router.
Please make sure that your smartphone/ tablet
is connected to the same Wi-Fi network.
NOTES
The frequency of the home Wi-Fi network has to
be set on the 2.4 GHz band. You can not configure
the appliance if your home network is set to the 5
GHz band.
If you are having trouble locating the WPA/WEP
Password, please contact your Internet Provider.
STEP 2
Download the Rosières E-Picurien App from the
Store.
Open the Rosières E-Picurien App and create
your user profile by taping on “Register”. Accept
the privacy policy and fill in the required fields.
NOTES
The App is available for Android (version 4.4 or
higher) and iOS (version 8.0 or higher) devices.
If you already have a Rosières E-Picurien user
profile, you can login using your credentials.
STEP 3
In the homepage, tap on the icon with the three
bars on the top left to enter your profile, then tap
on “REGISTER NEW APPLIANCE” and select the
name of the product that you want to enroll.
STEP 4
Insert the purchase date of your appliance
(DD/MM/YYYY), then tap on “Proceed”.
STEP 5
Insert the 16 digits of the serial number or scan
the QR code on the appliance. Tap on “Next.
Check data correctness and tap on “Confirm”.
Once the system has recognized the product, tap
on “Next”.
STEP 6
On the appliance - Turn the knob to the WI-FI
RESET program and wait 5 minutes. The
countdown will appear on the App, after which
you can complete enrollment.
In App- Tap on “Confirm”.
NOTES
To ensure correct data transfer, we recommend
that you stay with the device close to the
appliance.
STEP 7
Exit the Rosières E-Picurien App.
Go to your device Wi-Fi settings.
STEP 8
In the list of available Wi-Fi networks, select
“WIFIOVEN-xyzk”.
NOTES
If you do not find it, wait few more seconds or
proceed with a new scan.
STEP 9
Exit from the settings of your device.
Return to the Rosières E-Picurien App and wait
for the App to detect the appliance.
Once theWi-Fi Network is active” screen
appears, tap on “Next”.
EN 13
STEP 10
Insert the password of your home Wi-Fi
network.
Select the type of password (WEP or WPA), then
tap on “Confirm”.
NOTES
If this is not automatically synchronised by the
App, please insert the name of your home Wi-Fi
network in the first box; pay attention to the
difference between lowercase and uppercase.
STEP 11
Wait until the end of the data transfer process
between the App and the product, then tap on
Confirm”.CONNECTED appears on the
appliance display and then “REMOTE CONTROL
ON”.
The enrollment process is now finished.
IF THE SET UP IS NOT SUCCESSFUL
It's important to establish a good Wi-Fi signal
strength between the home router and the
appliance: low Wi-Fi signal strength would cause
the failure of the final stage of the set up. To assess
if this is the case, start the connection process
again from Step 1; when you get to Step 6, place
your device (smartphone or tablet) next to the
router and search forWIFIOVEN-xyzk net
generated by the appliance. If this does not come
up as an option, it means that the router cannot
see the appliance. In this case, we highly
recommend you to bring the router near the
appliance (if possible) or contact your internet
provider to purchase a compatible “Wi-Fi Range
Extenderto increase the signal strenght.
Remote control mode
Turn the program selection knob to the WI-FI
position: the wifi light will turn on and you can
now control the oven remotely.
NOTES
Warning, if the enrolled oven is left on the WI-FI
RESET position for more than 5 minutes, the oven
will be reset and you will have to proceed with a
new enrollment.
EN 14
3.2 Cooking Modes
EN 15
T °C
Suggested
180
Function
Dial
Function (Depends on the oven model)
LAMP: Turns on the oven light.
*
190
*Tested in accordance with the EN 60350-1 for the purpose of energy consumption declaration and energy class
210
230
220
220
MULTI-LEVEL: We recommend you use this method for poultry, pastries, fish and
vegetables. Heat penetrates into the food better and both the cooking and
preheating times are reduced. You can cook different foods at the same time with
or without the same preparation in one or more positions. This cooking method
gives even heat distribution and the smells are not mixed.
Allow about ten minutes extra when cooking foods at the same time.
DEFROST: When the dial is set to this position. The fan circulates air at room
temperature around the frozen food so that it defrosts in a few minutes without the
protein content of the food being changed or altered.
MASTER BAKE : This function allows to cook in a healthier way, by reducing the
amount of fat or oil required. The combination of heating elements with a
pulsating cycle of air ensures a perfect baking result.
GRILL: use the grill with the door closed.
The top heating element is used alone and you can adjust the temperature. Five
minutes preheating is required to get the elements red-hot. Success is guaranteed
for grills, kebabs and gratin dishes. White meats should be put at a distance from
the grill; the cooking time is longer, but the meat will be tastier. You can put red
meats and fish fillets on the shelf with the drip tray underneath. The oven has two
grill positions: Grill: 2140 W Barbecue: 3340 W
BOTTOM HEATING + FAN: The bottom heating element is used with the fan
circulating the air inside the oven. This method is ideal for juicy fruit flans, tarts,
quiches and pâté.
It prevents food from drying and encourages rising in cakes, bread dough and other
bottom-cooked food. Place the shelf in the bottom position.
CONVENTIONAL: Both top and bottom heating elements are used. Preheat the
oven for about ten minutes. This method is ideal for all traditional roasting and
baking. For seizing red meats, roast beef, leg of lamb, game, bread, foil wrapped
food (papillotes), flaky pastry. Place the food and its dish on a shelf in mid position.
PIZZA: With this function hot air circulated in the oven to ensure perfect result for
dishes such as pizza or cake.
WIFI ON: Oven allows wifi connection.
WIFI RESET: It allows wifi connection to be restarted.
*
50 ÷ MAX
T °C
Range
50 ÷ MAX
50 ÷ MAX
50 ÷ MAX
50 ÷ MAX
50 ÷ MAX
EN 16
4. Oven cleaning and maintenance
4.1 General notes on cleaning
The lifecycle of the appliance can be extended through regular cleaning. Wait for the oven to cool before
carrying out manual cleaning operations. Never use abrasive detergents, steel wool or sharp objects for
cleaning, so as to not irreparably damage the enamelled parts. Use only water, soap or bleach-based
detergents (ammonia).
GLASS PARTS
It is advisable to clean the glass window with absorbent kitchen towel after every use of the oven. To
remove more obstinate stains, you can use a detergent-soaked sponge, well wrung out, and then rinse
with water.
OVEN WINDOW SEAL
If dirty, the seal can be cleaned with a slightly damp sponge.
ACCESSORIES
Clean accessories with a wet, soapy sponge before rinsing and drying them: avoid using abrasive
detergents.
DRIP PAN
After using the grill, remove the pan from the oven. Pour the hot fat into a container and wash the pan in
hot water, using a sponge and washing-up liquid.
If greasy residues remain, immerse the pan in water and detergent. Alternatively, you can wash the pan
in the dishwasher or use a commercial oven detergent. Never put a dirty pan back into the oven.
4.2 Maintenance
Instruction for removal and cleaning of the side racks
1. Remove the wire racks by pulling them in the direction of the arrows (see below)
2. To clean the wire racks either put them in the dishwasher or use a wet sponge, ensuring that they are
dried afterwards.
3. After the cleaning process install the wire racks in reverse order.
REMOVAL OF THE OVEN WINDOW
1. Open the front window.
2. Open the clamps of the hinge housing on the right and left side of the front window by pushing them
downwards.
3. Replace the window by carrying out the procedure in reverse.
LOW-E
1
2
3
1.
2.
3.
4.
5.
6.
7.
REMOVAL AND CLEANING OF THE GLASS DOOR
1. Open the oven door.
2.3.4. Lock the hinges, remove the screws and remove the upper metal cover by pulling it upwards.
5.6. Remove the glass, carefully extracting it from the oven door (NB: in pyrolytic ovens, also remove
the second and third glass (if present)).
7. At the end of cleaning or substitution, reassemble the parts in reverse order.
On all glass, the indication "Pyro" must be legible and positioned on the left side of the door, close to the
left-hand lateral hinge. In this way, the printed label of the first glass will be inside the door.
EN 17
CHANGING THE BULB
1. Disconnect the oven from the mains supply.
2. Undo the glass cover, unscrew the bulb and replace it with a new bulb of the same type.
3. Once the defective bulb is replaced, replace the glass cover.
5. Troubleshooting
5.1 FAQ
PROBLEM POSSIBLE CAUSE SOLUTION
The oven does not heat up
The clock is not set Set the clock
A cooking function and
temperature has not been set
Ensure that the necessary
settings are correct
The oven does not heat up
EN 18
Steam and condensation on
the user interface panel
Clean with a microfiber
cloth the user interface
panel to remove the
condensation layer
No reaction of the touch
user interface
FR 19
Conseils De Securite
Lorsque vous ouvrez la porte après la cuisson, quelques gouttes d’eau
peuvent sortir de la porte. Cela dépend du type d’aliment que vous avez
cuisiné.
Pendant la cuisson, de l’humidité peut se condenser à l’intérieur de la
cavité ou sur la vitre de la porte. Il s’agit d’un phénomène normal. Pour
réduire cet effet, attendez 10-15 minutes après avoir allumé l’appareil
avant de mettre les aliments au four. La condensation disparaîtra de
toutes façons dès que le four aura atteint la température de cuisson.
• Cuisez les légumes dans un récipient avec couvercle plutôt que dans
un ustensile ouvert.
Évitez de laisser des aliments à l’intérieur du four plus de 15-20
minutes après cuisson.
• AVERTISSEMENT : Lappareil et ses parties accessibles chauffent
pendant l’utilisation.
Faites attention à ne pas toucher les parties chaudes.
AVERTISSEMENT : Les parties accessibles peuvent devenir très
chaudes quand le grill est en marche. Les enfants doivent être tenus à
une distance de sécurité.
AVERTISSEMENT : Vérifiez que l’appareil est éteint avant de remplacer
l’ampoule, pour éviter le risque de chocs électriques.
AVERTISSEMENT : Afin d’éviter tout risque lié à la réinitialisation
accidentelle de l’interrupteur thermique, l’appareil ne doit pas être
alimen par un dispositif de commutation externe, tel qu’une
minuterie, ou relié à un circuit régulièrement allumé et éteint.
Les enfants de moins de 8 ans doivent rester à une distance de
sécurité de l’appareil s’ils ne sont pas surveillés en permanence.
Les enfants ne doivent pas jouer avec l’appareil.
Lappareil peut être utilisé par des enfants de plus de 8 ans et par des
personnes dont les capacités physiques, sensorielles ou mentales sont
limitées, sans expérience ni connaissance du produit, uniquement s’ils
sont surveillés ou s’ils ont été informés de la manière dutiliser
l’appareil, en toute sécurité et qu’ils comprennent les risques possibles.
FR 20
Le nettoyage et l’entretien ne doivent pas être effectués par des
enfants sans surveillance.
N’utilisez pas de matériaux rugueux ou abrasifs ou de racloirs
métalliques acérés pour nettoyer les vitres des portes des fours, car cela
pourrait rayer la surface et provoquer la rupture de la vitre.
Coupez le four avant de retirer les pièces amovibles.
Après le nettoyage, remontez-les selon les instructions.
Utilisez uniquement la sonde à viande recommandée pour ce four.
N’utilisez pas un nettoyeur à vapeur pour le nettoyage.
Branchez le câble d’alimentation sur une prise de courant qui
supporte le voltage (le courant et la charge sont indiqués sur l’étiquette)
et vérifiez la présence d’une mise à la terre. La prise d’alimentation doit
supporter la charge indiquée sur l’étiquette et être dotée d’une mise à
la terre en état de fonctionnement. Le conducteur de mise à la terre est
jaune et vert. Cette opération doit être exécutée par le personnel
qualifié. En cas d’incompatibilité entre la prise d’alimentation et la fiche
du câble de l’appareil, demandez à un électricien professionnel de
remplacer la prise d’alimentation par un dispositif compatible.
La fiche du câble d’alimentation et la prise d’alimentation doivent être
conformes aux normes en vigueur dans le pays d’installation.
Il est possible de brancher l’appareil à la prise d’alimentation en
installant entre l’appareil et la prise d’alimentation un disjoncteur
multipolaire qui supporte la charge électrique maximale,
conformément aux lois en vigueur.
Le conducteur jaune et vert de mise à la terre ne doit pas être bloqué
par le disjoncteur. La prise d’alimentation ou le disjoncteur multipolaire
utilisé pour le branchement doit rester à tout moment accessible après
installation de l’appareil.
Le débranchement doit se faire à l’aide soit de la prise d’alimentation,
soit dun interrupteur installé sur le circuit électrique fixe,
conformément aux normes électriques.
Si le câble d’alimentation est endommagé, il doit être remplacé par un
câble ou un faisceau de câbles spécial disponible auprès du fabricant ou
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37

ROSIERES RFC3O3379IN WIFI Manuel utilisateur

Catégorie
Fours
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues