geratech WHD100 Manuel utilisateur

WHD100

In Room Full HD VideoWireless Kit

WHD100

In Room Full HD VideoWireless Kit

1

WHD100 Receiver

PC to TV Wireless Receiver

WHD100 Transmitter

PC to TV Wireless Transmitter

WHD100

In Room Full HD VideoWireless Kit

2

Table of Contents

TABLE OF CONTENTS ..........................................................................................................................

1. IMPORTANT INFORMATION ..............................................................................................................

2. INTRODUCTION ................................................................................................................................

2.1 PACKING CONTENT ...................................................................................................................

2.2 OVERVIEW ..................................................................................................................................

2.2.1 WHD100T (TX): PC TO TV TRANSMITTER ..........................................................................

2.2.2 WHD100R (RX): PC TO TV RECEIVER ................................................................................

2.2.3 REMOTE CONTROLLER UNIT (RCU) INSTRUCTION ........................................................

3. INSTALLATION ..................................................................................................................................

STEP 1: SETUP THE WHD100T TRANSMITTER ............................................................................

STEP 2: SETUP THE WHD100R RECEIVER ...................................................................................

STEP 3: BOOT UP THE WHD100T AND WHD100R .........................................................................

STEP 4: INSTRUCTION OF MULTIPLE TRANSMITTER SELECTION ............................................

STEP 5: MOUNTING THE WHD100R TO THE WALL

4. TROUBLESHOOTING ........................................................................................................................

4.1 WINDOWS OS DISPLAY SETTING OF LAPTOP FOR ENABLES EXTERNAL DISPLAY ..........

4.2 MAC OS DISPLAY SETTING OF LAPTOP FOR ENABLES EXTERNAL DISPLAY ....................

4.3 WINDOWS OS AUDIO SETTING OF LAPTOP FOR SWITCH TO HDMI OUTPUT .....................

5. SUPPORTED RESOLUTION ..............................................................................................................

6. AUDIO BIT RATE SUPPORT ..............................................................................................................

7. PRODUCT SPECIFICATION ...............................................................................................................

2

3

10

11

12

13

14

15

16

20

22

25

27

28

30

32

33

WHD100

In Room Full HD VideoWireless Kit

3

1. Important Information

Please take the time to read this user manual before using the WHD100. It contains important informa-

tion about operating your PC to TV wireless kit.

Our company’s limited warranty applies when the product is handled properly for intended use, in accor-

dance with its operating instruction. However, the warranty may be void in the following cases:

Repair, product modification or alteration have been performed by unauthorized service personnel

Damages caused by accidents, including but not limited to, lightning, water, fire, or moisture

Use of an AC adapter not compatible with the product and its voltage rating

The model number on the product has been altered, deleted, removed or made illegible.

WARNING!

RISK OF

ELECTRICAL

SHOCK

DO NOT OPEN

WARMING:

TO REDUCE THE RISK OF ELECTRICAL SHOCK

DO NOT REMOVE THE COVER

NO USER-SERVICEABLE PARTS ARE INSIDE

REFER SERVICING TO QUALIFIED PERSONNEL

Danger: Be careful with electricity.

Power to the units must be switched off before any work is undertaken, such as any AV device connec-

tion or TV connection.

Power outlet: To prevent electric shock, make sure to use the appropriate AC adapters as power

supply to the transmitter and the receiver.

Power cord: Be sure the power cord is routed so that it will not be stepped on or pinched by heavy

items.

Power overloading: Avoid overloading electrical outlets or extension cords which otherwise could

result in electric shock or fire.

Lightning: Disconnect the product from the power source if it is left unattended for a long period of

time, and to protect the product from lightning.

Always disconnect the power cord from the power outlet when you are not using your Full HD Video

wireless kit. This reduces the risk of electric shocks or fire.

Safety Precautions

WHD100

In Room Full HD VideoWireless Kit

4

Warning

This product should not be exposed to dripping or splashing. No object filled with liquids, such as

vases, should be placed on the product.

Object Entry: To avoid electric shock, never stick anything in the slots on the case or remove the cover.

Place receiver/transmitter on a flat, hard and stable surface

Ventilation: Do not block the ventilation slots on the receiver/transmitter or place any heavy object on

the top cover. Blocking the air flow could damage the receiver. Arrange components so that air can

flow freely around the receiver. Ensure that there is adequate ventilation if the receiver is placed in a

stand. Put the receiver/transmitter in a property ventilated area, away from direct sunlight or any

source of heat.

Water Exposure: To reduce the risk of fire or electric shock, do not expose the receiver/transmitter to

rain or moisture.

This is indoor solution.

Our company has the right to modify this document without any notice.

DECLARATION OF CONFORMITY

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference

received, including interference that may cause undesired operation.

EMI (Electro Magnetic Interference) tested.

EN 55022 Information technology equipment----

Radio disturbance characteristics--- Limits and methods of measurement

EN 61000-3-2 Electromagnetic compatibility (EMC)---

Part 3-2:Limits---Limits for harmonic current emissions(equipment input current up to and including 16

A per phase)

EN 61000-3-3 Electromagnetic compatibility (EMC)---

Part 3:Limits---Section 3: Limitation of voltage changes, voltage fluctuations and flicker in public

low-voltage supply systems, for equipment with rated current 16 A per phase and not subject to

conditional connection

EN 55024 Information technology equipment----

Equipment---Immunity characteristics---Limits and methods of measurement

EN 301 489-1

Electromagnetic compatibility and Radio spectrum Matters (ERM); Electro Magnetic Compatibility

(EMC) standard for radio equipment and services; Part 1: Common technical requirements

WHD100

In Room Full HD VideoWireless Kit

5

EN 301 489-17

Electromagnetic compatibility and Radio spectrum Matters (ERM); Electro magnetic Compatibility

(EMC) standard for radio equipment; Part 17: Specific conditions for 2,4 GHz wideband transmission

systems, 5GHz high performance RLAN equipment and 5,8 GHz Broadband Transmitting Systems

EN 60065 Audio video and similar electronic apparatus—Safety requirements

TRADEMARK INFORMATION

HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks of HDMI Licensing

LLC.

Special Notice

Never use this product nearby an aircraft or medical facility. It can cause interference or undesirable

effect on the operation result.

Use of this product in the following locations may result in abnormal video and audio output (noise,

blocked image... etc,).

Product installed in the walls made of concrete.

Product situated near the refrigerator or metal fitment.

A cluttered room where the wireless signals may be blocked

This product has been tested and manufactured to comply with each country’s safety rules. However,

there is no guarantee that interference will not occur in some installation scenario. If the interference

happens, increase the distance between the transmitter and receiver.

WHD100 may interfere 5GHz wireless devices, such as routers or other wireless devices. Therefore,

if you have an 802.11n router, configure it to the 2.4 GHz band rather than the 5GHz band.

Optimal range between WHD100 transmitter and receiver is between 2 and 7 meters within line of

sight.

EN

CAUTION: Using the RF module in the US

Any changes or modifications not expressly approved by the grantee of this device could void the

user's authority to operate the equipment.

This equipment must be installed and operated in accordance with provided instructions and the

antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20

cm from all persons and must not be co-located or operating in conjunction with any other antenna

or transmitter. End-users and installers must be provide with antenna installation instructions and

transmitter operating conditions for satisfying RF exposure compliance.

Outdoor operations in the 5150 ~ 5250MHz, 5600~5650MHz band are prohibited.

This device has no Ad-hoc capability for 5250~5350MHz and 5470~5725MHz.

Outdoor operations in the 5470~5725MHz band are prohibited. This device could not be used in the

5600~5650MHz.

The Device not operation in 5600~5650MHz.

WHD100

In Room Full HD VideoWireless Kit

6

Outdoor operations in the 5470~5725MHz band are prohibited. This device could not be used in the

5600~5650MHz.

The Device not operation in 5600~5650MHz.

Industry Canada regulatory information Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any interference, including inter-

ference that may cause undesired operation of the device.

The user is cautioned that this device should be used only as specified within this manual to meet

RF exposure requirements. Use of this device in a manner inconsistent with this manual could lead

to excessive RF exposure conditions.

The following statement must be included with all versions of this document supplied to an OEM or

integrator, but should not be distributed to the end user.

This device is intended for OEM integrators only.

Please See the full Grant of Equipment document for other restrictions.

This device must be operated and used with a locally approved access point.

The following regulatory and Safety notices must be published in documentation supplied to the

end user of the product or system incorporating an adapter in compliance with local regulations,

Host system must be labeled with “Contains FCC ID: XXX-XXXXX”, FCC ID displayed on label.

System Warning

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursu-

ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television recep-

tion, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connect-

ed.

Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Using the System in the US

Any changes or modifications not expressly approved by the grantee of this device could void the

user's authority to operate the equipment.

WHD100

In Room Full HD VideoWireless Kit

7

This equipment must be installed and operated in accordance with provided instructions and the

antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20

cm from all persons and must not be co-located or operating in conjunction with any other antenna

or transmitter. End-users and installers must be provide with antenna installation instructions and

transmitter operating conditions for satisfying RF exposure compliance.

Outdoor operations in the 5150~5250MHz, 5600~5650MHz band are prohibited.

This device has no Ad-hoc capability for 5250~5350MHz and 5470~5725MHz.

Outdoor operations in the 5470~5725MHz band are prohibited. This device could not be used in the

5600~5650MHz.  The device not operation in 5600~5650MHz.

CAUTION: Using the System in the Canada

Europe – EU Declaration of Conformity

Industry Canada regulatory information Operation is subject to the following two conditions:

1. This device may not cause interference,

2. This device must accept any interference, including interference that may cause undesired

operation of the device. The user is cautioned that this device should be used only as specified

within this manual to meet RF exposure requirements. Use of this device in a manner inconsistent

with this manual could lead to excessive RF exposure conditions.

This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following

test methods have been applied in order to prove presumption of conformity with the essential require-

ments of the R&TTE Directive 1999/5/EC:

EN 60065: 2002+A1: 2006+A11: 2008+A2 2010

Safety of Information Technology Equipment

EN50371 : 2002 Generic standard to demonstrate the compliance of low power electronic and elec-

trical apparatus with the basic restrictions related to human exposure to electromagnetic fields (10

MHz - 300 GHz) -- General public

EN 301 893 V1.5.1: 2008 Broadband Radio Access Networks (BRAN); 5 GHz high performance

RLAN; Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive

EN 301 489-1 V1.8.1: 2008 Electromagnetic compatibility and Radio Spectrum Matters (ERM); Elec-

troMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common techni-

cal requirements

EN 301 489-17 V2.1.1 2009 Electromagnetic compatibility and Radio spectrum Matters (ERM);

ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific

conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equip-

ment

Hereby, Geratech declares that this Full HD video wireless kit is in compliance with the essential

requirements and other relevant provisions of Directive 1995/5/EC.

WHD100

In Room Full HD VideoWireless Kit

8

Industry Canada statement

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

IMPORTANT NOTE: (IC: 9078A-ZRF32200)

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator

& your body.

Caution:

The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for

harmful interference to co-channel mobile satellite systems;

High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz

and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN

devices.

IMPORTANT NOTE: (IC: 9078A-RF31200M)

Radiation Exposure Statement:

The product comply with the US/Canada portable RF exposure limit set forth for an uncontrolled

environment and are safe for intended operation as described in this manual. The further RF expo-

sure reduction can be achieved if the product can be kept as far as possible from the user body or

set the device to lower output power if such function is available.

IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop configurations or co-lo-

cation with another transmitter), then the Canada authorization is no longer considered valid and the

IC ID can not be used on the final product. In these circumstances, the OEM integrator will be

responsible for re-evaluating the end product (including the transmitter) and obtaining a separate

Canada authorization.

WHD100

In Room Full HD VideoWireless Kit

9

Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio

exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne

doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y

compris un brouillage susceptible de provoquer un fonctionnement indésirable.

NOTE IMPORTANTE: (IC: 9078A-ZRF32200)

Déclaration d'exposition aux radiations:

Les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une

utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satel-

lites mobiles utilisant les mêmes canaux;

De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance

sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz

et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux

dispositifs LAN-EL.

NOTE IMPORTANTE: (IC: 9078A-RF31200M)

Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis

et le Canada établies pour un environnement non contrôlé.

Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux exposi-

tions RF peut être augmentée si l'appareil

peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la

puissance de sortie la plus faible si une telle fonction est disponible.

NOTE IMPORTANTE:

Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configura-

tions d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation

du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final.

Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris

l'émetteur) et l'obtention d'une autorisation distincte au Canada.

French translation:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un envi-

ronnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de

distance entre la source de rayonnement et votre corps.

Déclaration d'exposition aux radiations:

WHD100

In Room Full HD VideoWireless Kit

10

2. Introduction

WHD100 is a Full HD wireless transmission device.

This solution delivers uncompressed 1080p full HD video and audio content to your existing HDTV set

wirelessly. It operates the transmission in 4.9 GHz~ 5.9 GHz frequencies and it can adjust its commu-

nication frequency automatically in case of interference from another RF system. With built-in Omni-di-

rectional antennas, it can transmit uncompressed video content to 7 meters (20 feet) LOS (Line of

sight) with no latency.

2.1 Packing Content

Please check whether the following items are present in the package. If any items missed or damaged,

please call your dealer.

WHD100

In Room Full HD VideoWireless Kit

11

2.2 Overview

2.2.1 WHD100T (TX): PC to TV Transmitter

Pairing button

The button reserved for

multiple transmitter &

receiver pairing usage.

3

LED Status Indicator

The LED indicator is lit solid

blue when the power is on and

wireless link

1

USB Power

Connect the transmitter

to the desktop or laptop’s

USB port with the

provided USB cable.

4

HDMI IN

Plug in Transmitter to PC

/ Notebook or any

Source device that have

an HDMI port directly.

2

Lateral view

Top view

WHD100

In Room Full HD VideoWireless Kit

12

2.2.2 WHD100R (RX): PC to TV Receiver

Front Panel Buttons and LEDs

Power Button with LED

indicator

Press to turn the receiver on

and off. The indicator in the

power button lights up in blue

when the power is on, and

turns red in standby mode.

1

INFO. Button

Press this button for OSD

displayed the information

on the HDTV screen.

2

Status LED

Display the video

status information.

3

Main Unit Back Panel

HDMI OUT

Connect to HDTV set via

an HDMI cable.

2

DC IN

Connect to receiver’s

power adapter.

1

WHD100

In Room Full HD VideoWireless Kit

13

2.2.3 Remote Controller Unit (RCU) Instruction

POWER Button

Press to turn the Receiver

on/off. When RX Power LEDs

are red, press Power button

point at to RX, it can wake up

each other automatically.

1

INFO. Button

Press this button to display

OSD for system related infor-

mation on HDTV connected on

receiver.

2

Transmitter NO. Button

Press to switch different trans-

mitter inputs. Please refer CH3,

step6 for detail instruction.

3

SOURCE Button

Press to switch the audio/video

sources input connected to

transmitter directly. (No function

for WHD100 product.)

4

IR Button

Press to switch the IR Blaster

frequency to meet Source

device’s requirement. It can

switch IR Blaster frequency 47K

to 56K to 36K recurring. (No

function for WHD100 product.)

5

WHD100

In Room Full HD VideoWireless Kit

14

3. Installation

Step 1: Setup the WHD100T transmitter

Connect an HDMI-ready computer to the WHD100T:

Plug the transmitter’s HDMI connector to the HDMI-ready computer’s “HDMI OUT” or Source player’s “HDMI OUT”

directly.

1

Power supplied by USB port of computer through the USB cable (included on package). Or connect the supplied power

adapter to the mini USB port of the WHD100T and a wall socket. The LED indicator should lights up in blue when the

WHD100T is connected to the computer through USB.

2

WHD100

In Room Full HD VideoWireless Kit

15

Connect the HDMI cable to the HDMI OUT jack of the receiver and to your HDTV set (or an HD projector).

1

Connect the supplied power adapter to the DC IN jack of the WHD100R and a wall socket. When it’s connected to the

power mains and Power LED indicator on the POWER button lights up in blue.

2

Step 2: Setup the WHD100R receiver

HDTV set Connection with WHD100R:

WHD100

In Room Full HD VideoWireless Kit

16

Step 3: Boot up the WHD100T and WHD100R

Place the two AAA batteries into the remote control.

1

After the power cord is plugged into the electrical outlet, the WHD100 will be turned on and link established

automatically.

2

When unplug the power of WHD100T, WHD100R will enter Standby mode (POWER LED of receiver is lit in

red) when link drop over 10mins.

3

WHD100

In Room Full HD VideoWireless Kit

17

When WHD100T in Standby mode (Receiver POWER LED is lit in red), plug in the power of WHD100R, the receiver will

wakes up the transmitter automatically to establish a link.

4

During the warm-up period, the POWER LED will blink in blue until the signal link between the transmitter and the

receiver is established. It will spend around 15 ~ 20 seconds for boot up and link established if the operation is in normal

condition.

5

Ensure your TV set or projector is in “HDMI input” mode, and is already powered on.

WHD100

In Room Full HD VideoWireless Kit

18

If all operation is normal, the POWER LED and INFO./CHANNEL LED will glow in solid blue. Please

refer to the below form containing detailed LED indicator and OSD description of transmitter / receiver:

6

Item / Mode

Standby

Initial Boot

up / Warm

up

Searching

available

channels

Wireless

linked Mode

Video format

is recognized

Video format

not recognized

(Note C)

No input from

selected source

(Note B)

Static Blue

Static Blue Static Blue

Blinking

(Slowly)

Blinking

(Quickly)

Status

Description

Power LED

(on RX)

Status LED

(on RX)

For power

saving

mode.

Static Red

off

It will spend

15 ~ 20

seconds for

system boot

up.

Blinking

Blue

Blinking

Continuing

search available

channels If

system can’t

establish link

over 80s after

initialization.

(Note A & D)

OSD Display

(on RX)

Blinking

Blue

4 level, looping.

Looping display

these two OSD

-

WHD100

In Room Full HD VideoWireless Kit

19

Note:

A. If the RF connection over 80sec and still not established, it might link is lost or the transmitter is most

likely out of range. You may have to verify the range and adjust or shorten the distance between your

HDTV set with the transmitter and the receiver. The maximum video transmission range for 1080p

content is up to 23 feet in line of sight (LOS). < The minimum range is 6.5 feet. >

B. Please make sure the computer have been power on and switched the signal output to HDMI out;

also try to re-plug the HDMI cable to make sure the HDMI connector had settled well.

C. If there is no video displayed and OSD displayed “Not Supported Format”, this is an indication that

the video frame rate from the computer is not supported, please refer chapter 5 to switch a supported

video timing.

D. If you have more than one pair of WHD100, each transmitter and receiver should be at least 6.5 feet

away from one another. If both the transmitter and the receiver exist in the same room, the suggested

the distance between the two is 6.5 feet minimum.

TRANSMITTER/RECEIVER Status on OSD vs. buttons:

1. Press the POWER button on the top of Receiver to enter “Active-Standby mode” from “Active mode”.

- The OSD Shows: (Display 3secs and then enter Active-Standby mode.)

2. Press the INFO. button on the top of Receiver, the Signal Quality, Source, Channel and resolution will

be displayed for user reference. Press INFO. button again for exit.

OSD Displayed :

7

HDMI1 CH1 1280x1024

= OFF

La page est en cours de chargement...

geratech WHD100 Manuel utilisateur

geratech WHD100 Manuel utilisateur

dans d''autres langues

Autres documents