Peavey GPS Le manuel du propriétaire

Marque: Peavey

Modèle: GPS

Catégorie: Amplificateurs audio

Taper: Le manuel du propriétaire

Ce manuel convient également à

GPS Series Power Amplifier

GPS

™

Series Operation Manual

For more information on other great Peavey products, go to your local Peavey dealer or online at www.peavey.com.

Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

Intended to alert the user of the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the product.

CCAAUUTTIIOONN::

Risk of electrical shock — DO NOT OPEN!

CCAAUUTTIIOONN::

To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.

Refer servicing to qualified service personnel.

WWAARRNNIINNGG::

To prevent electrical shock or fire hazard, this apparatus should not be exposed to rain or

moisture‚ and objects filled with liquids‚ such as vases‚ should not be placed on this apparatus. Before

using this apparatus‚ read the operating guide for further warnings.

Este símbolo tiene el propósito, de alertar al usuario de la presencia de “(voltaje) peligroso” sin

aislamiento dentro de la caja del producto y que puede tener una magnitud suficiente como para

constituir riesgo de descarga eléctrica.

Este símbolo tiene el propósito de alertar al usario de la presencia de instruccones importantes sobre la

operación y mantenimiento en la información que viene con el producto.

PPRREECCAAUUCCIIOONN::

Riesgo de descarga eléctrica ¡NO ABRIR!

PPRREECCAAUUCCIIOONN::

Para disminuír el riesgo de descarga eléctrica, no abra la cubierta. No hay piezas útiles

dentro. Deje todo mantenimiento en manos del personal técnico cualificado.

AADDVVEERRTTEENNCCIIAA::

Para prevenir choque electrico o riesgo de incendios, este aparato no se debe exponer a

la lluvia o a la humedad. Los objetos llenos de liquidos, como los floreros, no se deben colocar encima

de este aparato. Antes de usar este aparato, lea la guia de funcionamiento para otras advertencias.

Ce symbole est utilisé dans ce manuel pour indiquer à l’utilisateur la présence d’une tension dangereuse

pouvant être d’amplitude suffisante pour constituer un risque de choc électrique.

Ce symbole est utilisé dans ce manuel pour indiquer à l’utilisateur qu’il ou qu’elle trouvera d’importantes

instructions concernant l’utilisation et l’entretien de l’appareil dans le paragraphe signalé.

AATTTTEENNTTIIOONN::

Risques de choc électrique — NE PAS OUVRIR!

AATTTTEENNTTIIOONN::

Afin de réduire le risque de choc électrique, ne pas enlever le couvercle. Il ne se trouve à

l’intérieur aucune pièce pouvant être reparée par l’utilisateur. Confiez I’entretien et la réparation de

l’appareil à un réparateur Peavey agréé.

AAVVIISS::

Dans le but de reduire les risques d’incendie ou de decharge electrique, cet appareil ne doit pas

etre expose a la pluie ou a l’humidite et aucun objet rempli de liquide, tel qu’un vase, ne doit etre pose

sur celui-ci. Avant d’utiliser de cet appareil, lisez attentivement le guide fonctionnant pour

avertissements supplémentaires.

Dieses Symbol soll den Anwender vor unisolierten gefährlichen Spannungen innerhalb des Gehäuses

warnen, die von Ausreichender Stärke sind, um einen elektrischen Schlag verursachen zu können.

Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam

machen, die Handhabung und Wartung des Produkts betreffen.

VVOORRSSIICCHHTT::

Risiko — Elektrischer Schlag! Nicht öffnen!

VVOORRSSIICCHHTT::

Um das Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es

befinden sich keine Teile darin, die vom Anwender repariert werden könnten. Reparaturen nur von

qualifiziertem Fachpersonal durchführen lassen.

WWAARRNNUUNNGG::

Um elektrischen Schlag oder Brandgefahr zu verhindern, sollte dieser Apparat nicht Regen

oder Feuchtigkeit ausgesetzt werden und Gegenstände mit Flüssigkeiten gefuellt, wie Vasen, nicht auf

diesen Apparat gesetzt werden. Bevor dieser Apparat verwendet wird, lesen Sie bitte den

Funktionsführer für weitere Warnungen.

IIMMPPOORRTTAANNTT SSAAFFEETTYY IINNSSTTRRUUCCTTIIOONNSS

WWAARRNNIINNGG::

When using electrical products, basic cautions should always be followed, including the following:

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers)

that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one

wider than the other. A grounding type plug has two blades and a third grounding plug. The wide blade or third prong is

provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point

they exit from the apparatus.

11. Note for UK only: If the colors of the wires in the mains lead of this unit do not correspond with the terminals in your

plug‚ proceed as follows:

a) The wire that is colored green and yellow must be connected to the terminal that is marked by the letter E‚ the earth

symbol‚ colored green or colored green and yellow.

b) The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black.

c) The wire that is colored brown must be connected to the terminal that is marked with the letter L or the color red.

12. Only use attachments/accessories provided by the manufacturer.

13. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a

cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

14. Unplug this apparatus during lightning storms or when unused for long periods of time.

15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

16. Never break off the ground pin. Write for our free booklet “Shock Hazard and Grounding.” Connect only to a power

supply of the type marked on the unit adjacent to the power supply cord.

17. If this product is to be mounted in an equipment rack, rear support should be provided.

18. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in suscep-

tibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise

for a sufficient time. The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the

following permissible noise level exposures:

Duration Per Day In Hours Sound Level dBA, Slow Response

890

692

495

397

2100

1 1⁄2 102

1105

1⁄2 110

1⁄4 or less 115

According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Ear plugs or protectors to the

ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if exposure

is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is

recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be

protected by hearing protectors while this unit is in operation.

SSAAVVEE TTHHEESSEE IINNSSTTRRUUCCTTIIOONNSS!!

EENNGGLLIISSHH

GGPPSS

™™

SSeerriieess PPoowweerr AAmmppss

SPECIFICATIONS

OUTPUT POWER

Stereo mode, both channels driven

2 ohms, 1 kHz, 0.1% THD

4 ohms, 1 kHz, 0.1% THD

8 ohms, 1 kHz, 0.1% THD

Bridge mode, mono

4 ohms, 1 kHz, 0.1% THD

8 ohms 1 kHz, 0.1% THD

RATED OUTPUT POWER:

Stereo mode, both channels driven

4 ohms, 20 Hz to 20 kHz, 0.03% THD

8 ohms, 20 Hz to 20 kHz, 0.02% THD

4 ohms, 20 Hz to 20 kHz, 0.1% THD

8 ohms, 20 Hz to 20 kHz, 0.08% THD

SLEW RATE:(Typical value)

Stereo mode, each channel

Bridge mode, mono

INPUT SENSITIVITY &

IMPEDANCE:

@ rated output power, 4 ohms

unbalanced, 1/4" phone jack

Balanced, XLR (polarity selectable)

Overall system gain per channel

FREQUENCY RESPONSE:

Stereo mode, both channels driven

+0m -1 dB @ 1 WRMS, 4 ohms

+0, -0.2 dB @ rated output, 4 ohms

DAMPING FACTOR: (Typical

value)

Stereo mode, both channels driven

8 ohms

Hum & Noise:

Stereo mode, both channels driven

Below rated output power, 4 ohms

GPS

™

900

450W RMS per channel

330W RMS per channel

200W RMS per channel

900W RMS

660W RMS

300W RMS per channel

1700W RMS per channel

40 Volts per µsec

80 Volts per µsec

0.87V RMS

20 k ohms

10 k ohms per leg

40X (+32 dB)

5 Hz to 50 kHz

20 Hz to 20 kHz

Greater than 400

100 dB, unweighted

GPS

™

1500

750W RMS per channel

550W RMS per channel

320W RMS per channel

1500W RMS

1100W RMS

500W RMS per channel

280W RMS per channel

40 Volts per µsec

80 Volts per µsec

1.12V RMS

20 k ohms

10 k ohms per leg

40X (+32 dB)

5 Hz to 50 kHz

20 Hz to 20 kHz

Greater than 400

100 dB, unweighted

GPS

™

2600

1300W RMS per channel

950W RMS per channel

620W RMS per channel

2600W RMS

1900W RMS

900W RMS per channel

600W RMS per channel

40 Volts per µsec

80 Volts per µsec

1.54V RMS

20 k ohms

10 k ohms per leg

40X (+32 dB)

5 Hz to 100 kHz

10 Hz to 30 kHz

Greater than 700

100 dB, unweighted

GPS

™

3500

1200W RMS per channel

775W RMS per channel

2400W RMS

1050W RMS per channel

750W RMS per channel

40 Volts per µsec

80 Volts per µsec

1.62V RMS

20 k ohms

10 k ohms per leg

40X (+32 dB)

5 Hz to 100 kHz

10 Hz to 30 kHz

Greater than 325

100 dB, unweighted

SSppeecciiffiiccaattiioonnss ssuubbjjeecctt ttoo cchhaannggee wwiitthhoouutt nnoottiiccee..

GG PP SS

™™

SS EE RR II EE SS

PPOOWWEERR AAMMPPLLIIFFIIEERRSS

Congratulations on your purchase of the new GPS Series amplifier by Peavey Electronics. Years of power amp design and

testing have produced a totally refined, dynamic power amp product line. The GPS Series consists of the GPS 900, GPS 1500,

GPS 2600, GPS 3400 and GPS 3500. Each model features tunnel cooling, two variable-speed fans, initialization protection

and DDT

™

speaker protection. There are, however, differences between the various models such as output power and

connections. This guide will describe each feature of your GPS Series amplifier and note the features common to specific

models. The chart below offers a quick reference.

Please read this guide in its entirety. Pay close attention to the various warnings within as they pertain to the

safety of you and your product. Each section will begin with a short description of the information you can expect

to obtain within. This should help you to locate the material you are looking for in a timely manner. Once again,

congratulations and thank you for buying Peavey!

UUNNPPAACCKKIINNGG//RREEGGIISSTTRRAATTIIOONN

Inspect the amplifier during unpacking. If you find any damage, notify your dealer immediately. Be sure to save

the carton and all packing materials. Should you ever need to ship the unit back to Peavey Electronics, one of its

service centers, or the dealer, use only the original factory packing. Please fill out your registration card at this

time. It is important that you complete the entire form and mail it to Peavey Electronics in order for your warranty

to apply.

IInnssttaallllaattiioonn aanndd MMoouunnttiinngg

GPS Series amplifiers are 2-rack-space units that mount in a standard 19-inch rack. On all amplifiers, four front

panel mounting holes are provided. Refer to the specifications for your specific model in this manual.

QQuuiicckk SSttaarrtt

The following section lists the steps for basic usage. This is only a quick reference. It is very important that you

read the entire manual in order to ensure the safe and optimum operation of your GPS Series amplifier.

TToo sseett uupp tthhee aammpplliiffiieerr ffoorr bbaassiicc uussaaggee::

1. Rack mount the amplifier in the location where it is to be used, remembering to allow for adequate access and

cooling space. For more information, see the section on Cooling Requirements.

2. Make input connections, balanced or unbalanced, to the combination input connector on the rear panel. See

the sections on The INs and OUTs of MODE SELECTION for more information.

3. Connect speakers to the output jacks or binding posts. Be sure to make the correct output connections for

stereo or bridged mono configuration. See the section on The INs and OUTs of MODE SELECTION for more

information.

4. Make power connections, allowing for proper current draw. See the section on AC Mains Circuit Size

Requirements for more information.

5. Turn down (fully counterclockwise) the two gain attenuators on the front panel. Turn the front panel AC switch

to “ON,” and bring up the gain attenuators to the desired levels.

AACC PPoowweerr

The following section will describe the AC power features of your GPS Series amplifier. AC power is a critical

element in power amplification. Please read this section carefully, paying special attention to any warning signs.

Refer to the diagram below and on page 8 to locate these features. Refer to page 7 for operation notes regarding

AC power.

NNOOTTEE::

Always make connections to your GPS Series amplifier while the unit is turned off.

11.. RReemmoovvaabbllee AACC PPoowweerr CCoorrdd ((LLooccaatteedd oonn tthhee rreeaarr ooff tthhee uunniitt))

This receptacle is for the IEC line cord (included), which provides AC power to the unit. Connect the line

cord to this connector and to a properly grounded AC supply. Damage to the equipment may occur if an

improper line voltage is used. (See voltage marking on unit.) Never remove or cut the ground pin of the line

cord plug. This unit is supplied with a properly rated line cord. When lost or damaged, replace this cord

with one of the proper ratings.

22.. AACC PPoowweerr SSwwiittcchh ((LLooccaatteedd oonn tthhee ffrroonntt ooff tthhee uunniitt.. SSeeee ddiiaaggrraamm oonn ppaaggee 99..))

A two-position power switch is on the right side of the front panel. With the top portion of the switch

pushed to the “IN” position the amplifier is “ON”. Press the bottom portion of the switch to the “IN”

position to turn the unit “OFF”.

33.. PPoowweerr LLEEDD ((LLooccaatteedd oonn tthhee ffrroonntt ooff tthhee uunniitt.. SSeeee ddiiaaggrraamm oonn ppaaggee 99..))

The Power LEDs illuminate to indicate the amplifier is turned on.

TThhee IInnss aanndd OOuuttss ooff MMooddee SSeelleeccttiioonn

Once you have provided proper AC power to the amplifier, you may now connect to the inputs and outputs.

Remember to do this while the power to the unit is turned off (Power LED are not lit). The rear panel of your GPS

Series amplifier provides a central location for all input and output connections. Regardless of the GPS model, all

input connections are located at the bottom-center portion of the rear panel and all output connections are

located at the top-center portion. In addition, your amplifier can operate in either stereo or bridged (mono) mode.

All GPS Series amplifiers have DDT compression. However, only GPS models 900 and 1500 have a switch to defeat

this feature. This section will describe these areas of your GPS Series amplifier in detail.

MMooddee SSeelleeccttiioonn

44.. MMooddee sswwiittcchh

This switch determines which mode your amplifier will operate in. Before connecting your input signal and

speaker cables to the amp, you must determine how you want the amp to function. Two modes of operation

are offered on your amplifier, stereo or bridged (seperate).

Stereo:

When we use the term “stereo” we are referring to two channels, not necessarily left and right. Therefore,

in “stereo” mode there are essentially two power amps regardless of input type. You may use a stere input,

one stereo input to each channel of the GPS, or you may send two mono inputs to the GPS in the same

manner. A good example of two separate inputs would be the use of one channel for mono mains and one

channel for mono monitor signals. In order to select the “stereo” mode of operation you must place the

Mode Switch in the “out” position. In this mode, Channel A Output is supplied by the Channel A Input.

Channel B Output is supplied by Channel B Input.

Bridged or Mono:

In the “bridge” mode the two channels of the amplifier combine to form a single mono channel. The benefit

of using your amplifier in this mode is that the power is doubled. Refer to the specifications in this manual

for detailed output power specs on your specific model. To use the GPS Series amp in “bridge” mode, place

the Mode Switch to the “in” position where the switch remains down. The amp is now a mono amplifier and

only requires a single input. Plug your input signal into Channel A only for “bridge” mode operation.

Channel B input must not have anything connected.

Note for GPS 900 and 1500:

When these models are switched to “bridge” mode, the Power LED (3) for Channel B will no longer

illuminate.

NNoottee::

Refer to the Outputs section for an explanation of how the Mode Switch affects the speaker outputs.

IInnppuuttss

55.. CChhaannnneell AA CCoommbbiinnaattiioonn IInnppuutt

GGPPSS 990000 AANNDD 11550000

These GPS Series amplifiers offer both XLR electronic balanced and phone jack quasi-balanced inputs for

each channel using Neutrik

’s new “combo” connector to save panel space.

RReeaarr PPaanneell

6 7 5

The female XLR inputs are connected to dual OP AMP circuitry which offers very low noise and extremely

high common mode rejection ratio to minimize outside interference!

The female 1/4" phone jack input in the center of the “combo” connectors are also connected to a unique

“quasi-balanced” input circuitry. When used, these 1/4" jacks are not “chassis grounded” but connected to

ground through a relatively low impedance circuit which is part of a “ground loop” elimination circuit

associated with the input. This will normally allow “hum free” operation when relatively short 1/4" cable

patches are made to this input by various outputs from other equipment that share the same rack with this

amp. This “quasi-balanced” circuit is “automatic”, and is virtually invisible in normal usage. It cannot be

defeated. Use only a two-conductor (TS) phone plug when connecting to the 1/4" input of this connector.

GGPPSS 22660000,, 33440000 aanndd 33550000

These GPS Series amplifiers offer both XLR electronic balanced and phone jack balanced/unbalanced

inputs for each channel using Neutrik's new “combo” connector to save panel space.

The female 1/4" phone jack input in the center of the “combo” connectors is also connected to a unique

balanced/unbalanced input circuitry. When used, these 1/4" jacks can accept both unbalanced two-

conductor (TS) and balanced three-conductor (TRS) inputs. Balanced operation is always recommended for

optimum signal-to-noise. If unbalanced operation is a required, always keep the input cable to a minimum

length to avoid excessive noise.

66.. CChhaannnneell BB CCoommbbiinnaattiioonn IInnppuutt

This connector is identical to the Channel A Combination Input (5) except it is not used during “bridge”

mode [See Mode Switch (4).]

77.. IInnppuutt PPoollaarriittyy

Located between the Channel A and Channel B Inputs is a recessed Input Polarity switch (7) that allows the

user to select the desired polarity (phase) of the XLR inputs. This switch is a push-push type and a small

diameter “tool” is required to select the desired position. Set to the out (default) position, the polarity is

pin #3 positive, pin #2 negative, and pin #1 ground. This is the polarity found on most Peavey power

amplifiers. Although this is not the world “standard” (IEC) polarity, it was chosen by Peavey more than 20

years ago, and thus we offer this polarity to be consistent with products both past and present. If this

amplifier is used with other competitive products which use the IEC standard polarity, then the “in”

position of switch (7) should be selected yielding pin #2 positive, pin #3 negative, and pin #1 ground. As

with any electronic gear, polarity (phasing) is important because the loudspeaker enclosures associated

with this power amplifier must be in phase with any other loudspeaker enclosures associated with other

power amps. If one loudspeaker system were to “push” while the other “pulls”, a serious sound

“cancellation” could result. Changing the setting of the polarity switch has the same effect as reversing the

polarity of the loudspeaker connections at the output.

88.. TThhrruu

Each channel has a female phone jack (8) labeled “thru”. This Thru jack offers very flexible patching

capability. When the XLR input of the combination connectors (5 and 6) are used, this THRU jack is the

output of the electronic balanced input circuitry, and as such can be used as a “line out” to connect to the

other input jack on this amplifier or other amps in the same rack. Thus, one balanced mixer feed can be

connected to the amp via the XLR connector and then further distributed (unbalanced) locally via the THRU

jack. Alternatively, when the 1/4" phone jack input of the combination connectors (5 and 6) is used as the

input, the THRU jack becomes a “bridged” input to it (similar to a Y-cord), again allowing this input signal

to be patched to the other input jack on this amplifier or other amps in the system.

IImmppoorrttaanntt::

The THRU

jack is not intended to be an “input”, and inadvertent usage as such will result in excessive loading of the

input source. Although not a catastrophic mistake, it will cause a significant reduction in “system gain” due

to the loading, and will seriously limit the overall system performance.

OOuuttppuuttss

99.. SSppeeaakkeerr OOuuttppuutt CCoonnnneeccttoorrss

Each GPS Series amplifier offers two separate output sections featuring parallel outputs. The type of

output jack differs from model to model. Find the model and AC supply voltage of your unit to identify

which description is applicable to your product.

GGPPSS 990000 OORR GGPPSS 11550000 112200 VVAACC ((DDoommeessttiicc)) MMooddeellss::

These two models feature 1/4" output jacks located on the top-center of the rear panel. There are two

parallel 1/4" jacks per channel which are labeled either “CHANNEL A” or “CHANNEL B”. In addition to the

1/4" output jacks, Binding Posts (10) are also provided for each channel.

AAllll ootthheerr GGPPSS mmooddeellss::

These models offer dual Speakon

Quick Connectors. The Speakon

is a four-wire connector with the

connections labeled as 1+, 1-, 2+ and 2-. The Speakon connectors found on your GPS Series amplifier are

connected with pins 1+ and 2+ wired in parallel to the positive output. Pins 1- and 2- are wired in parallel to

the negative output. This is typical for each channel.

NNOOTTEE::

Consult your loud speaker specifications to determine the wiring configuration that will best suit

your system. The diagrams on pages 13 and 14 display the recommended hookup for your GPS Series

amplifier. In addition to the Speakon

Quick Connectors, Binding Posts (10) are also provided for each

channel.

1100.. BBIINNDDIINNGG PPOOSSTT OOUUTTPPUUTT CCOONNNNEECCTTOORRSS

Five-way binding post speaker outputs can be found on each channel regardless of model. For each

channel, the outputs are in parallel, hence the speaker connection cables can be terminated with banana

plugs or stripped wires for use in the binding post terminals as well as the output connectors (9). For

sustained high power applications, the use of the binding post terminals is recommended; however, care

must be exercised to assure the correct speaker polarity. The red binding posts are the signal outputs from

each channel, and the black binding posts are chassis ground. The red binding post should be connected to

the positive inputs of the associated loudspeakers. For “bridge” mode operation, only the red binding

posts are used, and the associated loudspeaker load is connected between the two red binding posts. The

red binding post associated with Channel A should be considered the positive output for the system and

thus should be connected to the positive input of the associated loudspeaker system.

WWAARRNNIINNGG::

Regardless of what connections are used, the minimum parallel speaker load should always be

limited to 2 Ohms per channel or 4 Ohms “bridge” mode for any application (4 Ohms per channel/8 Ohms

bridge for GPS 3500). Operation at loads of 4 Ohms per channel or 8 Ohms “bridge” mode is more

desirable for sustained operation applications due to the fact that the amplifier will run much cooler at this

loading. Operation above 4 Ohms per channel and even open circuit conditions can always be considered

safe.

DDDDTT CCOOMMPPRREESSSSIIOONN

1111.. DDDDTT DDEEFFEEAATT

This switch is used to defeat the DDT compression used to protect against signal clipping.

OOnnllyy tthhee GGPPSS

990000 aanndd 11550000 mmooddeellss ooffffeerr tthhiiss ffeeaattuurree..

It is recommended to leave the DDT compression enabled at all

times to protect your speakers from damaging square waves. The DDT function is disabled when the switch

is pressed to the “in” position. The DDT LEDs (12) will illuminate when DDT compression is occurring in that

particular channel.

FFRROONNTT PPAANNEELL CCOONNTTRROOLLSS//IINNDDIICCAATTOORRSS

The following section describes the controls and indicators found on the front panel of your GPS Series

amplifier. The Power Switch and LED are explained in a previous section, AC Power.

1122.. DDDDTT LLEEDDss

The DDT LEDs will illuminate when signal compression is occurring in that channel. If you have a GPS 900

or 1500 and you have the DDT compression defeated, these LED will indicate the channel is clipping.

1133.. SSiiggnnaall LLEEDDss

Each channel has a Signal LED, which comes on when the amplifier channel output exceeds 1 Volt.

1144.. IInnppuutt GGaaiinn

Each channel has an Input Gain control used to adjust the gain of the input signal. Maximum power

amplifier input gain (minimum sensitivity) is achieved at the full clockwise setting (30 dB or 40x). This

setting yields maximum mixer/system headroom. A setting of less than full clockwise will yield lower

system noise at the expense of headroom.

1155.. FFaann GGrriillll ((llooccaatteedd oonn ffrroonntt aanndd rreeaarr ppaanneell))

Two continuously variable-speed DC fans supply cool air to the amplifier.

GGPPSS 990000 aanndd 11550000

The fans operate at a quiet, low speed when the unit is turned on. The speed of the fans increase as the

amplifier heatsinks require cooling. (See Operation Notes.)

GGPPSS 22660000,, 33440000 aanndd 33550000

The fans do not operate when the unit is first turned on. The operation and speed of the fans are

temperature dependent and change as the amplifier heatsinks require cooling. (See Operation Notes.)

13 3

FFrroonntt PPaanneell

DDOO NNOOTT BBLLOOCCKK TTHHIISS EEXXHHAAUUSSTT PPOORRTT!!

During the operation of your GPS Series amplifier, it will require fresh

air intake in order for the tunnel cooling to function properly. Blocking this air exhaust port or the air intake

ports on the rear could result in thermal shutdown of your amplifier.

OOppeerraattiioonn NNootteess

AACC MMaaiinnss CCiirrccuuiitt SSiizzee RReeqquuiirreemmeennttss

Power requirements for the GPS Series amplifiers are rated at “typical” music conditions. The maximum

power current draw rating is limited by the amplifier’s circuit breaker. Consult the specification sheet for

the current that each amplifier will demand. AC mains voltage must be the same as that indicated on the

back of the amplifier. Damage caused by connecting the amplifier to improper AC voltage is not covered by

any warranty.

LLiinnee CCoorrdd

For your safety, we have incorporated a removable 3-wire line (mains) cable with proper grounding

facilities. It is not advisable to remove the ground contact under any circumstances. If it is necessary to use

the equipment without proper grounding facilities, suitable grounding adapters should be used. Less noise

and greatly reduced shock hazard exists when the unit is operated with the proper grounded receptacles.

NOTE: Always turn off the amplifier before making audio connections. As an extra precaution, have the

input attenuator turned down during power-up.

CCOOOOLLIINNGG RREEQQUUIIRREEMMEENNTTSS ((GGPPSS 990000 aanndd 11550000))

These GPS Series amplifiers use a forced-air cooling system to maintain a low, even operating temperature.

Cooling air is drawn by synchronized, variable-speed fans mounted on the back panel, and exhausts

through slots on the front panel. The fans will remain at low speed until internal operating temperature

rises above 45

C. Make sure that there is enough space around the back of the amplifier to allow air to

enter. The normal operating temperature is 55

C. This is a very cool temperature when compared to most

amplifier standards. What this means to you is a noticeable increase in product life. On the GPS 900 and

1500 models, the fans will turn on simultaneously when temperature activated.

CCOOOOLLIINNGG RREEQQUUIIRREEMMEENNTTSS ((AAllll mmooddeellss eexxcceepptt GGPPSS 990000 aanndd 11550000))

These GPS Series amplifiers use a forced-air cooling system to maintain a low, even operating temperature.

Cooling air is drawn by continuously variable speed fans mounted on the back panel, and exhausts through

slots on the front panel. The fan will remain inactive until internal operating temperature rises above 45

Make sure that there is enough space around the back of the amplifier to allow air to enter. The normal

operating temperature is 55

C. This is a very cool temperature when compared to most amplifier standards.

What this means to you is a noticeable increase in product life.

NNOOTTEE::

If the amplifier is rack-mounted, do not use doors or covers on the front or back while the unit is in

operation. Whatever type of rack you are using, make sure that heated air can escape freely, and that there

is no resistance to the intake of cool air through the back grill. Intake and exhaust air must flow without

resistance.

IINNPPUUTT CCOONNNNEECCTTIIOONNSS

The input connector accepts balanced and unbalanced audio signals. For use with an unbalanced source,

tie the inverting (-) input to ground by installing a jumper to the signal ground connection. If the inverting

input is left floating, a 6 dB loss in gain will result.

SSIIGGNNAALL MMOODDEE CCOONNFFIIGGUURRAATTIIOONN

GPS Series amplifiers are configured for two-channel (stereo) or bridged mode operation at the input

connectors and via Mode Switch. To send the same signal to both channels, connect the input signal to

Channel A via the input connector. Run a jumper from the Thru jack of Channel A to the input of Channel B.

Both channels then share Channel A’s input signal, but will operate independently. Speakers are connected

as in two-channel (stereo) mode.

Bridged mode converts the amplifier into a single-channel unit with a power rating equal to the sum of

both channels’ power ratings, and at a load rating of twice that of the single-channel rating. In bridged

mode, the channels operate at opposite polarity of each other so that one channel “pushes” and the other

“pulls” equally. Signal is connected to the Channel A Input connector. The speakers are connected only to

the designated “+” output terminals. Never ground either side of the speaker cable when the amplifier is in

bridged mode, as both sides are “hot”. For GPS Series amplifiers, the minimum nominal load impedance in

bridged mode is 4 Ohms (8 Ohms for GPS 3500); this is the equivalent of driving both channels at 2 Ohms

(4 Ohms for GPS 3500).

NNOOTTEE::

Regardless of operating mode,

NNEEVVEERR

connect amplifier outputs together!

SSppeeaakkeerr OOuuttppuutt CCoonnnneeccttiioonnss

Speakers are connected using the output connectors on the rear of your amplifier. Make sure the amplifier

is turned off before you change any output connections. Refer to the diagram on page 14 to view the wiring

configuration of the Speakon connectors if your model utilizes them. Consult the Wire Gauge Chart on page

14 to find a suitable wire gauge and minimize losses of power in the speaker cables. Also, make sure that

the load impedance is not lower than that rated for the amplifier.

PPrrootteeccttiioonn FFeeaattuurreess

The GPS Series incorporates protection features derived from Peavey’s extensive experience with reliability.

The amplifiers are ruggedly built from high quality components and feature comprehensive protection cir-

cuits to protect your amplifier from those “real world” occurrences.

DDDDTT

At the amplifier’s full power, or clipping point, the channel gain will automatically be reduced, guarding the

loudspeakers against damaging high power and continuous square waves that would otherwise be pro-

duced. This is indicated by illumination of the DDT LED. Operation is virtually transparent in use and full

signal bandwidth is maintained. However, if you have a GPS 900 or 1500 and choose to defeat the DDT

compression function, this will not apply and clipping may occur.

LLooaadd FFaauulltt CCoorrrreeccttiioonn

™™

LFC

™

(Load Fault Correction

™

) is an innovative circuit that will instantaneously reduce channel gain to allow

the amplifier to operate at a safe level into an abnormal load. Moderate activation of LFC is inaudible in

normal use. In addition, if extreme low impedance or a short circuit is encountered during high signal level

conditions, the amplifier’s output relay will open.

IInniittiiaalliizzaattiioonn PPrrootteeccttiioonn

™™

((IIPP

™™

))

™

operates every time the amplifier is turned on, or after a protect condition. During turn-on, the amplifier

goes into protect mode and leaves the speaker load disconnected until the amplifier determines that the

operating status is normal. The IP

™

circuit attenuates the signal during the initial turn-on or protect opera-

tion. After relay release, channel gain gradually increases to the attenuator setting to avoid unnecessary

stress on the loudspeakers.

TThheerrmmaall PPrrootteeccttiioonn

If the heatsink temperature or power transformer reaches an abnormally high temperature, the amplifier

will protect itself by disconnecting the speaker load until the amplifier returns to a normal temperature.

During this time, the Power LEDs will not illuminate for that particular channel, and the cooling fan(s) will

operate at maximum speed.

SShhoorrtt CCiirrccuuiitt

If an output is shorted, the LFC

™

, speaker relay and thermal circuits will automatically protect the amplifier.

The LFC

™

circuit senses the short circuit as an abnormal load condition and reduces the channel gain to a

safe level for the load. In extreme or severe conditions, the speaker relays will disconnect the load and ini-

tiate a power-on start-up sequence.

DDCC VVoollttaaggee PPrrootteeccttiioonn

If an amplifier channel detects DC voltage or subsonic signals at its output terminals, the speaker relay will

immediately open to prevent loudspeaker damage.

NNeeuuttrriikk

®®

iiss aa rreeggiisstteerreedd ttrraaddeemmaarrkk ooff NNeeuuttrriikk AAGG

SSppeeaakkoonn

®®

iiss aa rreeggiisstteerreedd ttrraaddeemmaarrkk ooff NNeeuuttrriikk AAGG

GPS 900/1500

150VAC Units Only

Channel A Input Source

All other GPS Models

NOTE: Always use a balanced input source if available.

NOTE: Minimum Load

Impedance is 2 Ohms.

NOTE: Minimum Load

Impedance is 2 Ohms.

GPS

™

Series Amplifiers

Recommended Connection for Stereo Mode

™

Channel B Input Source

1/4" jacks are wired in parallel

with binding post.

Tip = Positive

Ring = Negative

DTH

4215F

DTH

4215F

Speaker connectors are wired in

parallel with binding posts.

Pins (1+) and (2+) are wired positive.

Pins (1-) and (2-) are wired negative.

To Additional Amplifier Input

Channel A Input Source

Channel B Input Source

To Additional Amplifier Input

GPS 900/1500

150VAC Units Only

(-)

To negative input

terminal of speaker

(+)

To positive input

terminal of speaker

Switch “in” for

Bridge Mode

Input Source

All other GPS Models

(-)

To negative input

terminal of speaker

(+)

To positive input

terminal of speaker

NOTE: Always use a balanced input source if available.

NOTE: Minimum Load

Impedance is 4 Ohms.

NOTE: Minimum Load

Impedance is 4 Ohms.

GPS

™

Series Amplifiers

Recommended Connection for Bridged Mode

To Additional

Amplifier Input

Switch “in” for

Bridge Mode

Input Source

To Additional

Amplifier Input

WIRE GAUGE CHART

Stranded Power Power Power

Cable Wire Loss Loss Loss

Length Gauge Into Into Into

(Feet)

(AWG) 8 Ohms 4 Ohms 2 Ohms

5' 18 AWG .79% 1.58% 3.16%

16 .05 1.0 2.0

14 .31 .62 1.24

12 .20 .40 .80

10 .125 .25 .50

10' 18 AWG 1.58% 3.16% 6.32%

16 1.0 2.0 4.0

14 .62 1.25 2.50

12 .40 .80 1.6

10 .25 .50 1.0

40' 18 AWG 8% 12.6% 25.2%

16 4.0 8.0 16.0

14 2.5 5.0 10

12 1.60 3.2 6.4

10 1.0 2.0 4.0

8 .625 1.25 2.50

80' 16 AWG 8.0% 16.0% 32.0%

14 5.0 10.0 20.0

12 3.2 6.4 12.8

10 2.0 4.0 8.0

GPS

™

900 SPECIFICATIONS

OUTPUT POWER: (Typical value) Stereo mode, both channels driven

2 Ohms, 1 kHz, .1 THD - 450 WRMS per channel

4 Ohms, 1 kHz, .1 THD - 330 WRMS per channel

8 Ohms, 1 kHz, .1 THD - 200 WRMS per channel

Bridge mode, mono

4 Ohms, 1 kHz, .1 THD - 900 WRMS

8 Ohms, 1 kHz, .1 THD - 660 WRMS

RATED OUTPUT POWER: Stereo mode, both channels driven

4 Ohms, 20 Hz to 20 kHz,0.03% THD - 300 WRMS per channel

8 Ohms, 20 Hz to 20 KHz,0.02% THD - 170 WRMS per channel

SLEW RATE: (Typical value)

Stereo mode, each channel - 40 Volts per usec

Bridge mode, mono - 80 Volts per usec

INPUT SENSITIVITY AND IMPEDANCE:

Input attenuator set @ FCW

@ rated output power, 4 Ohms - 0.90 VRMS (-1 dBV)

Unbalanced, 1/4" phone jack - 20 k Ohms

Balanced, XLR (phase selectable) - 10 k Ohms per leg

Overall system gain per channel - 40X (+32 dB)

FREQUENCY RESPONSE: (Typical) Stereo mode, both channels driven

+0,-1 dB, 1 WRMS, 4 Ohms - 5 Hz to 50 kHz

+0,-0.2 dB @ rated output, 4 Ohms - 20 Hz to 20 kHz

DAMPING FACTOR: (Typical value) Stereo mode, both channels driven

8 Ohms, 1 kHz - Greater than 400

HUM AND NOISE: Stereo mode, both channels driven

Below rated output power, 4 Ohms - 100 dB @ 120 Volts

POWER CONSUMPTION: Stereo mode, both channels driven

@ 1/8 rated power @ 2 Ohms - 540 Watts @ 120 VAC

WEIGHT: - 35.8 lbs. (16.2 kg)

Specifications subject to change without notice.

GPS

™

1500 SPECIFICATIONS

OUTPUT POWER: (Typical value) Stereo mode, both channels driven

2 Ohms, 1 kHz, .1 THD - 750 WRMS per channel

4 Ohms, 1 kHz, .1 THD - 550 WRMS per channel

8 Ohms, 1 kHz, .1 THD - 320 WRMS per channel

Bridge mode, mono

4 Ohms, 1 kHz, .1 THD - 1,500 WRMS

8 Ohms, 1 kHz, .1 THD - 1,100 WRMS

RATED OUTPUT POWER: Stereo mode, both channels driven

4 Ohms, 20 Hz to 20 kHz,0.03% THD - 500 WRMS per channel

8 Ohms, 20 Hz to 20 kHz,0.02% THD - 280 WRMS per channel

SLEW RATE: (Typical value)

Stereo mode, each channel - 40 Volts per usec

Bridge mode, mono - 80 Volts per usec

INPUT SENSITIVITY and IMPEDANCE:

Input attenuator set @ FCW

@ rated output power, 4 Ohms - 1.17 VRMS (+1 dBV)

Unbalanced, 1/4" phone jack - 20 k Ohms

Balanced, XLR (phase selectable) - 10 k Ohms per leg

Overall system gain per channel - 40X (+32 dB)

FREQUENCY RESPONSE: (Typical)

Stereo mode, both channels driven

+0,-1 dB, 1 WRMS, 4 Ohms - 5 Hz to 50 kHz

+0,-0.2 dB @ rated output, 4 Ohms - 20 Hz to 20 kHz

DAMPING FACTOR: (Typical value) Stereo mode, both channels driven

8 Ohms, 1 kHz - Greater than 400

HUM AND NOISE: Stereo mode, both channels driven

Below rated output power, 4 Ohms - 100 dB, unweighted

POWER CONSUMPTION: Stereo mode, both channels driven

@ 1/8 rated power @ 2 Ohms - 1080 Watts @ 120 VAC

WEIGHT: - 39.2 lbs. (17.9 kg)

Specifications subject to change without notice.

GPS

™

2600 SPECIFICATIONS

Rated Power (2 x 2 Ohms) - 1,300 Watts @ 1 kHz both channels driven at <0.15% T.H.D.

Rated Power (2 x 4 Ohms) - 950 Watts @ 1 kHz both channels driven at <0.1% T.H.D.

Rated Power (2 x 8 Ohms) - 650 Watts @ 1 kHz both channels driven at <0.1% T.H.D.

Minimum Load Impedance - 2 Ohms

Maximum RMS Voltage Swing - 93 Volts

Frequency Response - 10 Hz - 100 kHz; +0, -.3 dB at 1 Watt

Power Bandwidth - 10 Hz - 40 kHz; +0, -3 dB at rated power

T.H.D. (2 x 2 Ohms) - <0.15% @ 1050 Watts from 20 Hz to 20 kHz with both channels driven

T.H.D. (2 x 4 Ohms) - <0.1% @ 900 Watts from 20 Hz to 20 kHz with both channels driven

T.H.D. (2 x 8 Ohms) - <0.1% @ 600 Watts from 20 Hz to 20 kHz with both channels driven

Input CMRR - > - 65d B @ 1 kHz

Voltage Gain - x 40 (32 dB)

Crosstalk - > -75 dB @ 1 kHz at rated power @ 8 Ohms

Hum and Noise - > -110 dB, “A” weighted referenced to rated power @ 8 Ohms

Power Consumption - > 1200 Watts

Slew Rate - > 40V/us

Damping Factor (8 Ohms) - > 700:1 @ 20 Hz to 1 kHz

SMPTE IMD - <0.1% 60 Hz and 7 kHz, 900W @ 4 Ohms

Input Sensitivity (x 40) - 1.54 Volts for 4 Ohm rated power, 1.27 Volts for 2 Ohm rated power

Input Impedance - 20 k Ohms, balanced

Current Draw @ 1/8 power@ 2 Ohms - 10 A @ 120 Volts

Cooling - Two 80 mm DC fans, off until heatsinks reach 45

C, then temperature dependant

variable speed

Controls - Two front panel attenuators

Indicator LEDs - Two Clip, two Signal, two Active

Protection - Thermal, DC, turn-on bursts, subsonic, incorrect loads

Connectors - XLR input, 6.3 mm phone type output patch, Speakon and Binding Post speaker

output, IEC mains input

Construction - 16 ga. steel reinforced with 12 ga.rack ears

Dimensions - 133 mm x 483 mm x 432 mm, 400 mm behind rear mounting ears

(5.23" x 19" x 17", 15.75" behind rack ears)

Weight - 45.7 lbs. (20.7 kg)

Specifications subject to change without notice.

GPS 3400 SPECIFICATIONS

Rated Power (2 x 2 Ohms): 1,700 Watts @ 1 kHz both channels driven at <0.15% T.H.D.

Rated Power (2 x 4 Ohms): 1,200 Watts @ 1 kHz both channels driven at <0.1% T.H.D.

Rated Power (2 x 8 Ohms): 750 Watts @ 1 kHz both channels driven at <0.1% T.H.D.

T.H.D. (2 x 2 Ohms): <0.15% @ 1350W from 20 Hz to 20 kHz with both channels driven

T.H.D. (2 x 4 Ohms): <0.1% @ 1000W from 20 Hz to 20 kHz with both channels driven

T.H.D. (2 x 8 Ohms): <0.08% @ 700W from 20 Hz to 20 kHz with both channels driven

Input CMRR: > - 65 dB @ 1 kHz

Voltage Gain: x 40 (32 dB)

Crosstalk: > -75 dB @ 1 kHz at rated power @ 8 Ohms

Hum and Noise: > -115 dB, “A” weighted referenced to rated power @ 8 Ohms

Power Consumption: > 1400 Watts

Slew Rate: > 40V/us

Damping Factor (8 Ohms): > 325:1 @ 20 Hz - 1 kHz

SMPTE IMD: <0.1% 60Hz and 7 kHz, 950W @ 4 Ohms

Input Sensitivity (x 40): 1.7 Volts for 4 Ohm rated power, 1.4 Volts for 2 Ohm rated power

Input Impedance: 20 k Ohms, balanced

Current Draw @ 1/8 rated

power @ 2 Ohms: 11.66 A @ 120 Volts

Cooling: Two 80 mm DC fans, off until heatsinks reach 45

C, then temperature dependent variable speed

Controls: Two front panel attenuators

Indicator LEDs: Two DDT/Clip, 2 Signal, 2 Power

Protection: Thermal, DC, turn-on bursts, subsonic, incorrect loads

Connectors: XLR input, 6.3mm phone type output patch, Speakon and Binding Post speaker output, IEC mains input

Construction: 16 ga. steel reinforced with 12 ga.rack ears

Dimensions: 133 mm x 483 mm x 432 mm, 400 mm behind rear mounting ears (5.23" x 19" x 17", 15.75" behind rack ears)

Weight: 49.8 lbs. (23.3 kg)

Specifications subject to change without notice.

GPS 3500 SPECIFICATIONS

Rated Power (2 x 4 Ohms): 1,200 Watts @ 1 kHz both channels driven at <0.1% T.H.D.

Rated Power (2 x 8 Ohms): 775 Watts @ 1 kHz both channels driven at <0.1% T.H.D.

Maximum RMS Voltage Swing: 89 Volts

Frequency Response: 10 Hz - 100 kHz; +0, -.3d B at 1 Watt

Power Bandwidth: 10 Hz - 40 kHz; +0, -3 dB at rated power

T.H.D. (2 x 4 Ohms): <0.1% @ 1050W from 20 Hz to 20 kHz with both channels driven

T.H.D. (2 x 8 Ohms): <0.08% @ 750W from 20 Hz to 20 kHz with both channels driven

Input CMRR: >- 65 dB @ 1 kHz

Voltage Gain: x 40 (32 dB)

Crosstalk: >-75 dB @ 1 kHz at rated power @ 8 Ohms

Hum and Noise: >-115 dB, “A” weighted referenced to rated power @ 8 Ohms

Power Consumption: >1,400 Watts

Slew Rate: >40V/us

Damping Factor (8 Ohms): >325:1 @ 20 Hz - 1 kHz

SMPTE IMD: <0.1% 60Hz and 7 kHz, 950W @ 4 Ohms

Input Sensitivity (x 40): 1.7 Volts for 4 Ohm rated power, 1.4 Volts for 2 Ohm rated power

Input Impedance: 20 k Ohms, balanced

Current Draw @ 1/8 rated

power @ 4 Ohms: 11.66 A @ 120 Volts

Cooling: Two 80 mm DC fans, off until heatsinks reach 45

C, then temperature dependent variable speed

Controls: Two front panel attenuators

Indicator LEDs: Two DDT/Clip, 2 Signal, 2 Power

Protection: Thermal, DC, turn-on bursts, subsonic, incorrect loads

Connectors: XLR input, 6.3mm phone type output patch, Speakon and Binding Post speaker output, IEC mains input

Construction: 16 ga. steel reinforced with 12 ga.rack ears

Dimensions: 133 mm x 483 mm x 432 mm, 400 mm behind rear mounting ears (5.23" x 19" x 17", 15.75" behind rack ears)

Weight: 51.3 lbs. (23.3 kg)

Specifications subject to change without notice.

EESSPPAAÑÑOOLL

GG PP SS

™™

SS EE RR II EE

AAMMPPLLIIFFIICCAADDOORREESS ddee PPOOTTEENNCCIIAA

Felicidades por tu compra del nuevo amplificador de potencia de la serie GPS de Peavey Electronics. Años de diseño y pruebas han

producido una línea de amplificadores dinámicos completamente refinada. La serie GPS consiste de los modelos GPS 900, GPS 1500, GPS

2600, GPS 3400 y GPS 3500. Cada modelo incluye enfriamiento por túnel, ventiladores variables de dos velocidades, protección de

iniciación y protección de bocinas DDT‘. Pero también hay diferencias entre los modelos, como las diferencias de potencia y conexiones.

Esta guía describirá todas las características de tu modelo GPS, y también hará nota de las características comunes entre los otros modelos

GPS. La gráfica inferior ofrece una guía de referencia rápida.

SPECIFICATIONS

OUTPUT POWER

Stereo mode, both channels driven

2 ohms, 1 kHz, 0.1% THD

4 ohms, 1 kHz, 0.1% THD

8 ohms, 1 kHz, 0.1% THD

Bridge mode, mono

4 ohms, 1 kHz, 0.1% THD

8 ohms 1 kHz, 0.1% THD

RATED OUTPUT POWER:

Stereo mode, both channels driven

4 ohms, 20 Hz to 20 kHz, 0.03% THD

8 ohms, 20 Hz to 20 kHz, 0.02% THD

4 ohms, 20 Hz to 20 kHz, 0.1% THD

8 ohms, 20 Hz to 20 kHz, 0.08% THD

SLEW RATE:(Typical value)

Stereo mode, each channel

Bridge mode, mono

INPUT SENSITIVITY &

IMPEDANCE:

@ rated output power, 4 ohms

unbalanced, 1/4" phone jack

Balanced, XLR (polarity selectable)

Overall system gain per channel

FREQUENCY RESPONSE:

Stereo mode, both channels driven

+0m -1 dB @ 1 WRMS, 4 ohms

+0, -0.2 dB @ rated output, 4 ohms

DAMPING FACTOR: (Typical

value)

Stereo mode, both channels driven

8 ohms

Hum & Noise:

Stereo mode, both channels driven

Below rated output power, 4 ohms

GPS

™

900

450W RMS per channel

330W RMS per channel

200W RMS per channel

900W RMS

660W RMS

300W RMS per channel

1700W RMS per channel

40 Volts per µsec

80 Volts per µsec

0.87V RMS

20 k ohms

10 k ohms per leg

40X (+32 dB)

5 Hz to 50 kHz

20 Hz to 20 kHz

Greater than 400

100 dB, unweighted

GPS

™

1500

750W RMS per channel

550W RMS per channel

320W RMS per channel

1500W RMS

1100W RMS

500W RMS per channel

280W RMS per channel

40 Volts per µsec

80 Volts per µsec

1.12V RMS

20 k ohms

10 k ohms per leg

40X (+32 dB)

5 Hz to 50 kHz

20 Hz to 20 kHz

Greater than 400

100 dB, unweighted

GPS

™

2600

1300W RMS per channel

950W RMS per channel

620W RMS per channel

2600W RMS

1900W RMS

900W RMS per channel

600W RMS per channel

40 Volts per µsec

80 Volts per µsec

1.54V RMS

20 k ohms

10 k ohms per leg

40X (-32 dB)

5 Hz to 100 kHz

10 Hz to 30 kHz

Greater than 700

100 dB, unweighted

GPS

™

3400

1700W RMS per channel

1200W RMS per channel

775W RMS per channel

3400W RMS

2400W RMS

1050W RMS per channel

750W RMS per channel

40 Volts per µsec

80 Volts per µsec

1.62V RMS

20 k ohms

10 k ohms per leg

40X (+32 dB)

5 Hz to 100 kHz

10 Hz to 30 kHz

Greater than 325

100 dB, unweighted

LLeess ssppéécciiffiiccaattiioonnss ssoonntt ssuujjeetttteess àà mmooddiiffiiccaattiioonn ssaannss aavviiss pprrééaallaabbllee

La page charge ...

Peavey GPS Le manuel du propriétaire

Marque: Peavey

Modèle: GPS

Catégorie: Amplificateurs audio

Taper: Le manuel du propriétaire

Ce manuel convient également à

GPS Series Power Amplifier

Télécharger le PDF

rapport

dans d''autres langues

English: Peavey GPS Owner's manual
español: Peavey GPS El manual del propietario
Deutsch: Peavey GPS Bedienungsanleitung

Peavey GPS Le manuel du propriétaire

Ce manuel convient également à

Peavey GPS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents