Homestar ZCLARINGTN Manuel utilisateur

Marque: Homestar

Modèle: ZCLARINGTN

Catégorie: Cheminées

Taper: Manuel utilisateur

clarington

299-3880-6

WALL-MOUNTED ELECTRIC FIREPLACE

FOYER ÉLECTRIQUE MURAL

Remote control

Hanging bracket

Bottom metal plate

Wall Plug

Fireplace insert

Front panel

Description Illustration

Qty

Hanging bracket screw

Metal plate screw

Drill

Unpack your fireplace the package and make sure you have all of the parts listed above. If parts are missing, please contact Customer

service at [email protected] or call 1-888-463-5698 immediately.

This appliance is designed for use as a supplementary heat source.

It is not intended to be the main source of heat.

Required Tools (not included)

Parts List

Before you start

E-1

Philips Screwdriver

IMPORTANT INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

E-2

licensed

19.The heater has a safety device that makes it stop working

once the inner temperature reaches 85º (± 2°C). To reset the

appliance, turn heater off and disconnect power, let it cool off

for 10 minutes and plug back in.

tap (outlet/power strip).

fire, electric shock or injury to persons.

The fireplace must not be used until it is securely fastened to

the wall. When choosing a location for your electric fireplace,

ensure that the general instructions are followed. Also, for

best results, install the electric fireplace away from direct

sunlight and dust.

20.

IMPORTANT INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

1. Do not connect this heater to a programmer, timer, separate remote control system or any other device that switches the heater on

automatically, since a fire risk exists if the heater is covered or positioned incorrectly.

2. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to

avoid a hazard.

3. In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external

switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

4. Do not use this heater in the immediate surroundings of a bath, shower or swimming pool.

5. If the glass becomes damaged, do not use the heater in order to avoid a hazard.

6. Always make sure the electrical socket is accessible and located adjacent to but not above the heater.

7. This heater must be mounted to the wall.

1. This heater must be fitted onto a flat wall. Ideally, install the heater directly to a brick wall, masonry surface or the internal wooden

frame of a plasterboard wall. If the wooden frame behind the plasterboard is not accessible use a minimum of four heavy-duty anchors

that are suitable for the weight of the heater.

2. We do not recommend that the heater be fitted to a wall covered in blown vinyl wallpaper, polystyrene tiles, etc.

3. It is important that the heater be never installed under a shelf or flammable materials such as curtains.

4. If the heater is to be mounted on to a plasterboard wall with wooden studs, make sure the wall is strong and stable enough to hold the

weight of the appliance. The vapor control barrier must not be damaged, and the structural members of the house must not be damaged.

We recommend minimum 12mm thick plasterboard.

5. Before drilling into walls, always check that there are no hidden wires, pipes, etc. Make sure that screws and wall plugs supplied are

suitable for supporting the unit in your surface. Consult a qualified person if you are not sure.

Handling and unpacking

Before starting the installation of this fireplace, please read the following:

1. The installation should be carried out by two adults to avoid injury or d amage. If for any reason it is considered too heavy, please

obtain assistance.

retteb si tI .tsiaw eht ta gnitsiwt diovA .kcab ruoy ton dna sgel ruoy dneB .thgiarts kcab ruoy peek syawla ,ecalperif eht gnitfil nehW .2

to reposition your feet.

elihw syawedis ro drawrof nael ton oD .tsiaw eht naht rehtar seenk eht morf dneb syawlA .gnidneb yvaeh pot / ydob reppu diovA .3

handling the heater.

.troppus rof sregnif fo spit eht esu ton oD .dnah eht fo mlap eht htiw retaeh eht pirg syawlA .4

5. Always keep the heater as close to the body as possible. This will mi

n imize the cantilever action.

6. Use gloves to provide additional grip.

7. Unpack the package and lift the product gently out of the box, put it on a flat surface with the front panel facing up.

E-3

Safety Warnings

Installation tips

IMPORTANT INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

1. Drill 4 holes (8mm diameter, 40mm deep) into wall.

2. Insert wall plugs (C) into the drilled holes.

3. Please refer to the diagram for hole locations.

4. The distance of the three top holes should be at least

600mm away from the ceiling.

Ax1 Bx1 Cx4 Dx4 Ex4

E-4

Hardware

Step 1

230mm 230mm

242mm

Fix wall plugs (C) into wall.

Note: Before drilling into walls, always check that there are

no hidden wires, pipes, etc. Make sure that screws and wall

plugs supplied are suitable for supporting the unit in your

surface. Consult a qualified person if you are

not sure.

IMPORTANT INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

1. While holding the hanging bracket (A) to the

drilled holes, insert screws (D) through the first,

third & fifth hole on the hanging bracket.

2. Screw the hanging bracket (A) in place with a

Philips screwdriver.

3. The screw should be fully inserted, flush to the

wall in order to avoid the screw head protruding

over the bracket.

4. Ensure the hanging bracket is securely attached.

1. Turn the fireplace insert on its back side.

2. Align the bottom metal plate (B) with the

screw holes located at the back of the

fireplace insert.

3. Use screws (E) to attach securely in place.

4. Ensure the bottom metal plate (B) is securely attached.

E-5

Step 2

Step 3

Attaching hanging bracket (A) into wall.

Attaching bottom metal plate (B)

to the back of fireplace insert.

IMPORTANT INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

E-6

1. Check to make sure the hanging bracket (A) is securely

attached to the wall.

2. Lift the fireplace insert and hang onto the hanging bracket.

3. Ensure the fireplace insert is securely installed onto the

hanging bracket.

4. Check again that the distance from the top of the firebox is

at least 400mm from the ceiling.

1. Insert the screw (D) through the hole of the bottom metal plate (B).

2. Fully tighten the screw to secure the fireplace to the wall.

3. Ensure the fireplace is secured to the wall.

Step 5

Step 4

Hanging the fireplace insert onto

the hanging bracket.

Locking the Fireplace insert to the wall.

IMPORTANT INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

E-7

1. Make sure the front panel is free of

debris and dirt.

2. Hold the panel securely and hang it onto

the fireplace hooks, located on the sides.

3. The panel should be secured on all four

hooks on the fireplace.

4. Check to make sure the panel is securely

in place.

1. Locate the hole on both left and right sides and insert

a screw (E) through the hook, into the fireplace insert.

2. Tighten screw to pass it through the hook, on both sides.

3. Ensure the front panel is secure.

Note: Tighten up the screw carefully, to avoid damage to

the front panel.

Step 6

Step 7

Attaching the front panel to the fireplace.

Installing the front panel.

E-8

12.7 kg / 15.1 kg

34 5/8 × 4 1/2 × 22 7/8 inch

88 × 11.5 × 58 cm

WALL MOUNTED FIREPLACE

SPECIFICATIONS

fireplace

appliance

heater

Control

Panel

Indicators

When a function is changed from the control panel or remote there will be a corresponding indicator displayed. The indicator shows

the function changed and the level selected. When the function is turned off, the corresponding indicator will fade off.

E-9

OPERATING INSTRUCTIONS

Figure 2

Figure 3

E-10

OPERATING INSTRUCTIONS

This button will not only put the fireplace insert in a standby mode, but also you can

see the flame effect through the screen. This will turn off all functions at once.

The fireplace contains a fan forced heater.

The default setting temperature is 72°F (22°C).

The thermostat setting range is 50°-86°F or 10°-30°C.

The thermostat is adjustable by 2°F or 1°C increments.

To change between °F and °C press and hold the HEATER button for 5 seconds.

Press the ECO button when the heater is on, to run the heater in a reduced wattage

range.

NOTE: Holding the ECO button for 3 seconds disables any heater functions.

To quickly heat up a cold room/space, press the BOOST button to run the heater at

the full rated wattage.

Pressing the BOOST button repeatedly will cycle through the following boost settings:

5 minutes, 10 min, 15 min, 20 min, 25 min, 30 min and off.

Pressing the timer button repeatedly will cycle through the following timer settings:

30 minutes, 1 hr, 2 hr, 3 hr, 4 hr, 5 hr, 6 hr, 7 hr, 8 hr and off.

The fireplace will automatically turn off when the timer reaches zero minutes.

5 different flame effects are available:

1. Snow White

2. Rubine

3. Ocean

4. Provence

5. Party

Party: In this mode, the unit will cycle automatically between all flame effects

periodically.

The flame speed is adjustable from remote control only.

Flame speed range: setting 1 the slowest to setting 5 the fastest.

The child safety lock is adjustable from remote control only.

Holding the child safety lock button for 3 seconds disables or enables all functions on

the control panel and remote control.

Brightness is adjustable from remote control only.

POWER

HEATER

ECO

BOOST

TIMER

BRIGHTNESS

FLAME MODE

FLAME SPEED

CHILD SAFETY

LOCK

This button controls the brightness of the flame effect.

FUNCTION ICON DESCRIPTION

Display shows “E2”.

There is no power.

Power cord gets warm.

The remote control is

not working.

The noise when the heater

is on is louder than normal.

Abnormal noise when the

heater is not on and the

flame effect is on.

Display shows “E1”.

Inspect the heater and check that the air inlets and outlets are

not blocked as this may cause overheating. Unplug the heater

for 10 minutes and allow it to cool down. Plug back in and turn

it on; check the heater for signs of overheating. If the problem

persists discontinue use of the heater and contact customer

service.

Contact customer service for a replacement thermostat sensor.

Check that unit is plugged into a standard 120V outlet. Press the

power button several times and make sure the power is set to

the “ON” position.

Adjust the temperature settings to ensure that the thermostat is

set higher than the current room temperature.

Check your heater cord and plug connections. Faulty wall outlet

connections or loose plugs can cause the outlet or plug to

overheat. Be sure the plug fits tight in the outlet. Heaters draw

more current than small appliances, overheating of the outlet

may occur even if it has not occurred with the use of other

appliances. During use check frequently to determine if your

plug outlet or faceplate is HOT! If so, discontinue use of the

heater and have a qualified electrician check and/or replace the

faulty outlet(s).

Change the remote batteries.

b. Contact Customer Service for a new heater/blower assembly.

Contact Customer Service for a new flame generator drive

motor.

E-11

TROUBLESHOOTING GUIDE

The heater does not blow

warm air.

Manual Reset overheat

protection has triggered.

The thermostat sensor is

broken or disconnected.

There is no power to the unit.

Thermostat setting is preventing

heater from turning on.

Normal operation.

There are no batteries or the

signal is poor.

a. The air intakes are dirty or

obstructed.

b. The blower/heater assembly

is defective.

The flame generator drive

motor is defective.

a. Check the air intakes for obstructions or high dust build up.

Operate remote control at a slow measured pace.

Press the remote control buttons with an even motion and gentle

pressure. Repeatedly pressing buttons in rapid succession may

cause the transmitter to malfunction.

POSSIBLE CAUSEPROBLEM CORRECTIVE ACTION

E-12

REPLACEMENT PARTS LIST AND EXPLODED VIEW

Flame Generator Drive Motor

Heater / Blower Assembly

Main Circuit Board

Emberbed Circuit Board

Flame Effect Circuit Board

LED Display

Flame Generator / Spinner

Remote Control

Control Panel Buttons

Thermostat Sensor

Emberbed with Log

Some parts and specifications may change without notice.

Part

Part Name

Figure 4

RGB Flame Circuit Board

For replacement parts, please call 1-888-463-5698 or visit www.homestarna.com, 7:00 am –5:00 pm CST, Monday – Friday.

E-13

REPLACING THE REMOTE

CONTROL BATTERY

DISPOSING OF USED

BATTERIES

When the remote control stops operating or its range seems reduced,

it is time to replace the batteries with new ones.

Do not mix old and new batteries.

Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad,

ni-mh, etc) batteries.

The batteries may contain hazardous substances that could

endanger the enviroment and human health.

This symbol appearing on the battery and/or packaging

indicates that used batteries must not be processed with

municipal waste. Instead they should be brought to the

appropriate collection point for recycling.

By correctly disposing of used batteries, you prevent potential

negative consequences for the environment and human health.

Recycling used materials also preserves our natural resources.

For more information about collecting and recycling used

batteries, please contact your local municipality, your waste

disposal service or the store where you purchased this product.

1. On the back end of the remote, press and slide the battery door

open and remove the old batteries.

2. Replace with two AAA batteries (not included), checking that the +

and - sides of the battery match the markings inside the battery

compartment.

3.Replace the battery compartment door.

NOTE:

Batteries should be removed if the product is to be left unused for a

long time.

INSTRUCTIONS

cleaning the appliance.

BASIC WARRANTY :

THIS WARRANTY IS VOID IF :

1 YEAR WARRANTY

The manufacturer warrants that this item is free from manufacturing and material defects for a period of one year

from date of purchase, subject to the following conditions and limitations.

1. Install and operate this item in accordance with the Installation

and operating instructions provided with the product at all times. Any

alteration, willful abuse, accident, or misuse of the product shall

nullify this warranty.

2. This warranty is non-transferable and is made to the original

owner, provided that the purchase was made through an authorized

supplier of the product.

3. This warranty is limited to the repair or replacement of part(s)

found to be

defective in material or workmanship, provided that such

part(s) have been subjected to normal conditions of use and service,

after said defect is confirmed by the manufacturer's inspection.

4. The manufacturer may, at its discretion, fully discharge all

obligations with respect to this warranty by refunding the wholesale

price of the defective part(s).

5. Any installation, labour, construction, transportation, or other

related costs/expenses arising from defective part(s), repa

ir,

replacement, or otherwise of same, will not be covered by this

warranty, nor shall the manufacturer assume responsibility for same.

6. The owner/user assumes all other risks, if any, including the risk

of any direct, indirect, or consequential loss or damages arising out

of the use, or inability to use the product, except as provided by law.

7. All other warranties expressed or implied with respect to the

product, its components and accessories, or any

obligations/liabilities on the part of the manufacturer are her

eby

expressly excluded.

8. The manufacturer neither assumes nor authorizes any third part

to assume, on its behalf, any other liabilities with respect to the sale

of the product.

9. The warranties as outlined within this document do not apply to

any accessories used in conjunction with the installation of this

product.

(a) The fireplace is subjected to prolonged periods of dampness or

condensation.

(b) Any alteration, willful abuse, accident, or misuse of the product.

service department at 1-888-463-5698, 7:00 a.m. – 5:00 p.m.

CST, Monday – Friday. Make sure you have your warranty,

your sales receipt, location of purchase and the model / serial

number of your product.

FOR CUSTOMER SERVICE:

WWW.HOMESTARNA.COM

[email protected]

1-888-463-5698

MADE IN CHINA

Imported by:

PRIMA INTERNATIONAL HOLDINGS LIMITED

RM A 7/F CHINA OVERSEAS BLDG 139

HENNESSY RD WANCHAI HONG KONG

E-14

Télécommande

Support de suspension

Plaque métallique inférieure

Cheville d’ancrage

Foyer

Panneau avant

Description Illustration

Qté

Vis pour support

Vis pour plaque métallique

Perceuse

Tournevis cruciforme

Déballez votre foyer électrique et vérifiez que vous avez toutes les pièces énumérées ci-dessus. Si des pièces sont manquantes,

veuillez communiquer avec le Service à la clientèle au [email protected] ou appelez le 1-888-463-5698

immédiatement.Cet appareil est conçu pour être utilisé en tant que source de chaleur d’appoint. Il ne doit pas être utilisé comme source

principale de chauffage.

Outils requis (non compris)

Liste des pièces

Avant de commencer

F-1

INSTRUCTIONS IMPORTANTES

INSTRUCTIONS DE MONTAGE

F-2

20.CONSERVEZ CES INSTRUCTIONS.

19. Cet appareil a un dispositif de sécurité qui l'arrête

automatiquement si la température interne atteint 85º (± 2°C).

Pour réinitialiser l'appareil, mettez les commandes en position

d'arrêt (off) et débranchez l'appareil de la prise murale. Laissez

l'appareil refroidir durant 10 minutes, puis rebranchez-le et

remettez-le en marche.

Le foyer ne doit pas être utilisé avant d’être solidement fixé au

mur. Avant de choisir un emplacement pour votre foyer

électrique, assurez-vous que les recommandations générales

aient été respectées. Aussi, pour de meilleurs résultats, placer

le foyer électrique loin des rayons directs du soleil et de la

poussière.

1. Ne pas brancher cet appareil à un dispositif de programmation, une minuterie, un système de télécommande ou tout autre dispositif

qui met l’appareil en marche automatiquement, car un risque d'incendie existe si l'appareil est couvert ou mal positionné.

2. Si le cordon d'alimentation est endommagé, il doit être remplacé par le fabricant, son agent de service ou un technicien qualifié afin

d'éviter tout danger.

3. Afin d'éviter un risque lié à la réinitialisation du coupe-circuit thermique, cet appareil ne doit pas être connecté à un dispositif de

commutation externe, une minuterie, ou relié à un circuit qui est régulièrement déclenché par les services publics.

4. Ne pas utiliser cet appareil dans les environs immédiats d'une baignoire, d'une douche ou d'une piscine.

5. Si le verre est endommagé, ne pas utiliser l'appareil afin d'éviter tout danger.

6. Assurez-vous toujours que la prise électrique est accessible et trouvé adjacent à, mais pas au-dessus du boîte à feu.

7. Cette boîte à feu doit être monté au mur.

1. Cet appareil doit être monté sur un mur droit. Idéalement, fixer l’appareil directement à un mur de brique, une surface de maçonnerie

ou aux montants de bois d’un mur en placoplâtre. Si les montants en bois derrière le mur de placoplâtre ne sont pas accessibles, utilisez

au minimum quatre chevilles d’ancrage ultra robustes, appropriées pour le poids du foyer.

2. Il n’est pas recommandé d’installer l’appareil sur un mur recouvert de papier peint en vinyle soufflé, de carreaux de polystyrène, etc.

3. Il est important que l’appareil ne soit pas installé sous une tablette ou des matériaux inflammables, tels que des rideaux.

4. Si l’appareil doit être monté sur un mur en placoplâtre ayant des montants en bois à l’arrière, vérifiez que le mur est suffisamment solide

et stable pour soutenir le poids de l’appareil. Il est important que le pare-vapeur ne soit pas endommagé et que les éléments de structure de

la maison ne soient pas endommagés. Nous recommandons une surface en placoplâtre de 12mm d'épaisseur au minimum.

5. Avant de percer les murs, vérifiez toujours qu'il n'y a pas de câbles, de tuyaux cachés, etc. Assurez-vous que les vis et chevilles

fournies sont appropriées pour supporter l'appareil dans votre surface. Consultez une personne qualifiée si vous n'êtes pas sûr.

Manipulation et déballage

Avant de commencer l’installation du foyer électrique, veuillez lire les directives suivantes:

1 L’installation doit être effectuée par deux adultes afin d’éviter le risque de blessures ou de dommages. Si l’appareil est trop lourd pour

quelque raison que ce soit, veuillez obtenir de l’aide supplémentaire.

2 Gardez votre dos bien droit en soulevant le foyer électrique. Pliez vos jambes plutôt que votre dos. Évitez les mouvements de torsion à

la taille; il vaut mieux changer la position de vos pieds.

3 Évitez les mouvements du haut du corps en transportant les charges lourdes. Pliez toujours les genoux plutôt que la taille. Ne vous

penchez pas vers l’avant ou de côté lorsque vous soulevez le foyer.

4 Agrippez toujours le foyer avec la paume de la main; ne le tenez pas du bout des doigts.

5 Gardez toujours le foyer aussi près du corps que possible, pour minimiser la charge en surplomb.

6 Portez des gants pour une meilleure prise.

7 Déballez le foyer et soulevez-le doucement hors de la boîte. Placez le foyer sur une surface droite, le panneau avant vers le haut.

F-3

Consignes de sécurité

Conseils d’installation

INSTRUCTIONS IMPORTANTES

INSTRUCTIONS DE MONTAGE

1. Percez 4 trous (8 mm diamètre, 40 mm profondeur) dans le

mur.

2. Insérez les chevilles d’ancrage (C) dans les trous percés.

3. Veuillez consulter le schéma pour l'emplacement des

trous.

4. La distance entre les trois trous supérieurs devrait être au

moins 600 mm du plafond.

Note : Avant de percer les murs, vérifiez toujours qu'il n'y a pas

de câbles, de tuyaux cachés, etc. Assurez-vous que les vis et

chevilles fournies sont appropriées pour supporter l'appareil

dans votre surface. Consultez une personne qualifiée si vous

n'êtes pas sûr.

Ax1 Bx1 Cx4 Dx4 Ex4

F-4

Quincaillerie

230mm 230mm

242mm

Étape 1

Fixer les chevilles d’ancrage (C)

dans le mur.

INSTRUCTIONS IMPORTANTES

INSTRUCTIONS DE MONTAGE

1. Tout en plaçant le support de suspension (A) vis-à-vis les trous

percés, insérez les vis (D) dans les premier, troisième et cinquième

trous sur le support de suspension.

2. Vissez le support de suspension (A) en place à l’aide d’un

tournevis cruciforme.

3. La vis devrait être entièrement insérée dans le mur, afin d'éviter

que la tête de vis ne dépasse du support de suspension.

4. Vérifiez que le support de suspension (A) est solidement fixé en

place.

1. Tournez le foyer à l’envers.

2. Alignez la plaque métallique (B) avec les trous de vis situés

à l'arrière du foyer.

3. Fixez la plaque en place à l’aide des vis (E).

4. Vérifiez que la plaque métallique (B) est solidement fixée

en place.

F-5

Étape 2

Étape 3

Fixation de la plaque métallique (B)

à l’arrière du foyer.

Fixation du support de suspension

(A) au mur.

INSTRUCTIONS IMPORTANTES

INSTRUCTIONS DE MONTAGE

La page charge ...

Homestar ZCLARINGTN Manuel utilisateur

Marque: Homestar

Modèle: ZCLARINGTN

Catégorie: Cheminées

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Homestar ZCLARINGTN User manual

Homestar ZCLARINGTN Manuel utilisateur

Homestar ZCLARINGTN Manuel utilisateur

dans d''autres langues

Autres documents