Toro 17in Curved-Shaft Gas Trimmer Manuel utilisateur

17 in. String Trimmer - Curved Shaft

Model No. 51955—311000001 & Up

18 in. String Trimmer - Straight Shaft

Model No. 51975—311000001 & Up

English (EN), French (FR), and Spanish (ES)

WARNING:

To reduce the risk of injury, the user must read and understand the operator’s manual. Save this manual.

Form No. 3369-612 Rev. A

If you have questions concerning

your trimmer, please call us

at 1-866-574-9242 (US) or

1-866-574-9243 (Canada).

2

READ THIS INFORMATION

Before you use your new trimmer, read the following helpful hints to

get you started.

Fueling

WARNING:

Gasoline and its vapors are highly ammable and

explosive. To prevent serious personal injury and

property damage, handle it with care. Keep away

from ignition sources and open ames, handle

outdoors only, do not smoke and wipe up spills

immediately.

1. Obtain a clean container that is approved for use with gasoline.

2. Mix all of the 2-cycle oil provided with 1 US gallon of 87-octane, unleaded

gasoline (50:1).

3. Fill the trimmer’s gas tank carefully.

Cold Starting vs. Warm Starting

When you restart the trimmer and you are not sure whether the engine is still warm, set the choke

lever to RUN and pull the starter cord. If the engine does not start within 5 pulls, refer to “To Start a

Cold Engine” later in this manual.

Flooded Engine

Will the engine start? If not, it may be ooded. Relax, this is easy to correct. Set the choke lever to

RUN. Squeeze the trigger and pull the starter cord quickly for 10 to 12 pulls.

If the engine does not start, refer to “Troubleshooting” later in this manual or call toll-free at

1-866-574-9242 (US) or 1-866-574-9243 (Canada).

STOP

CALL

1-866-574-9242 (US) or

1-866-574-9243 (Canada)

For questions concerning your trimmers,

call us toll free at 1-866-574-9242 (US) or

1-866-574-9243 (Canada).

WARNING: This product, its exhaust, and other substances that may become airborne

from its use may contain chemicals, including lead, known to the State of California to cause cancer,

birth defects, or other reproductive harm. Wash hands after handling.

California Proposition 65

3

Table of Contents

Introduction ................................................................................................................................................................................... 4

General Safety Rules .....................................................................................................................................................................5

Specic Safety Rules ....................................................................................................................................................................6

Symbols.........................................................................................................................................................................................7

Product Labels ..............................................................................................................................................................................8

Features ................................................................................................................................................................................... 9-10

Product Specications ...........................................................................................................................................................9

Assembly................................................................................................................................................................................11-13

Unpacking ............................................................................................................................................................................11

Connecting the Attachment to the Upper Shaft ...................................................................................................................12

Removing the Attachment from the Upper Shaft ................................................................................................................12

Attaching the Front Handle .................................................................................................................................................12

Attaching the Grass Deector .............................................................................................................................................. 13

Operation .....................................................................................................................................................................................14

Applications .........................................................................................................................................................................14

Fueling and Refueling the Trimmer .....................................................................................................................................14

Starting the Product .............................................................................................................................................................15

Stopping the Product ............................................................................................................................................................15

Operating the Trimmer ........................................................................................................................................................16

To Advance the Cutting Line ...............................................................................................................................................17

Cutting Tips .........................................................................................................................................................................17

Installing Line in Reel Easy String Head ............................................................................................................................18

Maintenance ................................................................................................................................................................................19

Cleaning the Product ............................................................................................................................................................19

Servicing the Product ........................................................................................................................................................... 19

Checking the Fuel Cap .........................................................................................................................................................19

Cleaning the Air Filter .........................................................................................................................................................19

Replacing the Spark Arrestor ............................................................................................................................................... 20

Replacing the Spark Plug .....................................................................................................................................................20

Idle Speed Adjustment .........................................................................................................................................................21

Storing the Product ..............................................................................................................................................................21

Transporting the Product .....................................................................................................................................................21

Installing Reel Easy String Head .........................................................................................................................................21

Emissions Maintenance Schedule ........................................................................................................................................22

High Altitude Engine Operation ..........................................................................................................................................22

Maintenance Schedule .........................................................................................................................................................23

Troubleshooting ..........................................................................................................................................................................24

Warranty ................................................................................................................................................................................ 25-26

Table of Contents

4

Introduction

Thank you for purchasing a Toro product.

We would like for you to be completely satised with your new product, so feel free to contact an authorized service dealer

for help with service, genuine Toro parts, or other information you may require.

Whenever you contact an authorized service dealer, always know the model and serial numbers of the product. These num-

bers will help the service representative provide exact information about your specic product. You will nd the model and

serial number decal located on the motor housing.

For your convenience, write the product model and serial numbers in the space below.

Model No.

Serial No.

Read this manual carefully to learn how to operate and maintain your product correctly. Reading this manual will help you

and others avoid personal injury and damage to the product. Although Toro designs, produces, and markets safe, state-of-the-

art products, you are responsible for using the product properly and safely. You are also responsible for training persons you

allow to use the product about safe operation.

The Toro warning system in this manual identies potential hazards and has special safety messages that help you and others

avoid personal injury, even death. DANGER, WARNING, and CAUTION are signal words that identify the level of hazard.

However, regardless of the hazard, be extremely careful. Two other words, “Important” and “Note,” highlight information.

Introduction

Data Label

5

Read All Instructions

 For safe operation, read and understand all instructions

before using this product. Follow all safety instructions.

Failure to follow all safety instructions listed below, can

result in serious personal injury.

 Do not allow children or untrained individuals to use

this unit.

 Never start or run the engine in a closed or poorly venti-

lated area; breathing exhaust fumes can kill.

 Clear the work area before each use. Remove all objects

such as rocks, broken glass, nails, wire, or loose string

which can be thrown or become entangled in the cutting

line or blade.

 Always wear eye protection with side shields marked to

comply with ANSI Z87.1 along with hearing protection

when operating this equipment.

 Wear heavy, long pants, long sleeves, boots, and gloves.

Do not wear loose tting clothing, short pants, sandals,

or go barefoot. Do not wear jewelry of any kind.

 Heavy protective clothing may increase operator fa-

tigue, which could lead to heat stroke. During weather

that is hot and humid, heavy work should be scheduled

for early morning or late afternoon hours when tem-

peratures are cooler.

 Product users on United States Forest Service land,

and in some states, must comply with re prevention

regulations. This product is equipped with a spark arres-

tor; however, other user requirements may apply. Check

with your federal, state, or local authorities.

 Never operate this unit on the operator’s left side.

 Secure long hair above shoulder level to prevent en-

tanglement in moving parts.

 Keep all bystanders, children, and pets at least

50 ft. away. Bystanders should be encouraged to wear

eye protection. If you are approached, stop the engine

and cutting attachment. In the case of bladed units,

there is the added risk of injury to bystanders from be-

ing struck with the moving blade in the event of a blade

thrust or other unexpected reaction of the saw.

 Do not operate this unit when you are tired, ill, or under

the inuence of alcohol, drugs, or medication.

 Do not operate in poor lighting.

 Keep rm footing and balance. Do not overreach. Over-

reaching can result in loss of balance or exposure to hot

surfaces.

 Keep all parts of your body away from any moving

part.

 To avoid hot surfaces, never operate the unit with the

bottom of the engine above waist level.

 Do not touch area around the mufer or cylinder of the

unit, these parts get hot from operation. Contact with

hot surfaces could result in possible serious personal

injury.

 Always stop the engine and remove the spark plug wire

before making any adjustments or repairs except for

carburetor adjustments.

 Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace any damaged parts before use.

 The cutting attachment should never rotate at idle dur-

ing normal use. The cutting attachment may rotate at

idle during carburetor adjustments.

 It has been reported that vibrations from hand-held

tools may contribute to a condition called Raynaud’s

Syndrome in certain individuals. Symptoms may in-

clude tingling, numbness, and blanching of the ngers,

usually apparent upon exposure to cold. Hereditary

factors, exposure to cold and dampness, diet, smok-

ing, and work practices are all thought to contribute

to the development of these symptoms. It is presently

unknown what, if any, vibrations or extent of exposure

may contribute to the condition. There are measures

that can be taken by the operator to possibly reduce the

effects of vibration:

a) Keep your body warm in cold weather. When

operating the unit wear gloves to keep hands and wrists

warm. It is reported that cold weather is a major factor

contributing to Raynaud’s Syndrome.

b) After each period of operation, exercise to increase

blood circulation.

c) Take frequent work breaks. Limit the amount of

exposure per day.

d) Keep the tool well maintained, fasteners tightened,

and worn parts replaced.

If you experience any of the symptoms of this condi-

tion, immediately discontinue use and see your physi-

cian about these symptoms.

 Mix and store fuel in a container approved for gasoline.

 Mix fuel outdoors where there are no sparks or ames.

Wipe up any fuel spillage. Move 30 ft. away from refu-

eling site before starting engine. Slowly remove the fuel

cap after stopping engine. Do not smoke when refuel-

ing.

 Stop the engine and allow to cool before refueling or

storing the unit.

 Allow the engine to cool; empty the fuel tank into a

container approved for fuel and secure the unit from

moving before transporting in a vehicle.

 Wear your protective equipment and observe all safety

instructions. For units equipped with a clutch, be sure

the cutting attachment stops turning when the engine

idles. When the unit is turned off make sure the cutting

attachment has stopped before the unit is set down.

Safety Rules

General Safety Rules

WARNING:

Read and understand all instructions. Failure to follow all instructions may result in electric shock, re

and/or serious personal injury.

6

Specific Safety Rules

Specific Safety Rules For Trimmer Use

 Inspect before use. Replace damaged parts. Make sure

fasteners are in place and secure. Check for fuel leaks.

 Replace string head if cracked, chipped, or damaged in

any way. Be sure the string head or blade is properly

installed and securely fastened. Failure to do so can

cause serious injury.

 Make sure all guards, straps, deectors, and handles are

properly and securely attached.

 Never use blades, ailing devices, wire, or rope. Use

only the manufacturer’s replacement line in the cutting

head. Do not use any other cutting attachment. To install

any other brand of cutting head to this string trimmer can

result in serious personal injury.

 Never operate unit without the grass deector in place

and in good condition.

 Maintain a rm grip on both handles while trimming.

Keep string head below waist level. Never cut with the

string head located over 30 in. or more above the ground.

 This product is intended for infrequent use by homeown-

ers and other occasional users for such general applica-

tions as trimming light and heavy vegetation, etc. It is not

intended for prolonged use. Prolonged periods of opera-

tion can cause circulatory problems in the user’s hands

due to vibration. For such use, it may be appropriate to

use a product having an anti-vibration feature.

7

Symbols

The following signal words and meanings are intended to explain the levels of risk associated with this

product.

SYMBOL SIGNAL MEANING

DANGER: Indicates an imminently hazardous situation, which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result

in minor or moderate injury.

CAUTION: (Without Safety Alert Symbol) Indicates a situation that may result in property

damage.

Symbols

Some of the following symbols may be used on this product. Please study them and learn their meaning for safe operation

of this product.

SYMBOL NAME EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand opera-

tor’s manual before using this product.

Eye and Hearing Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1 along with hearing protection when operating this

equipment.

Keep Bystanders Away Keep all bystanders at least 50 ft. away.

Ricochet

Thrown objects can ricochet and result in personal injury or prop-

erty damage.

No Blade

Do not install or use any type of blade on a product displaying this

symbol.

Gasoline and Oil

Use unleaded gasoline intended for motor vehicle use with an oc-

tane rating of 87 [(R + M)/2] or higher. This product is powered by

a 2-cycle engine and requires pre-mixing gasoline and 2-cycle oil.

8

Product Labels

Product labels and instructions are easily visible to the operator and are located near any area of potential danger.

Replace damaged or lost labels.

Part No. 940686099

Part No. 940657034

Part No. 940864003

Product Labels

ON STOP

Set choke lever to

Push bulb

Set choke lever to

and pull starter handle

sharply

Set choke lever to

Pull starter handle until engine runs,

Part No. 940230132

Part No. 940865001

Part No. 940627020

9

Features

Product Specifications

Name Specification

Engine 25.4 cc Full Crank

Cutting Width

Model No. 51955 17 in.

Model No. 51975 18 in.

Line Size .095 in.

Weight

Model No. 51955 11.6 lbs.

Model No. 51975 12.5 lbs.

Specifications

10

Features

KNOW YOUR PRODUCT

See Figure 1.

The safe use of this product requires an understanding of the

information on the tool and in this operator’s manual as well

as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules, in both this manual and the opera-

tor’s manuals for all attachments that your are using with

this power head.

Engine

The engine is powerful and easy to start. It is effectively

counterbalanced, which allows for less vibration and more

durability.

Grass Deflector

The grass deector helps protect you from ying debris.

Grass Shield

The grass shield prevents grass from wrapping around the

trimmer shaft.

Ergonomic Design

The design of the product provides for easy handling. It is

designed for comfort and ease of grasp when operating in

different positions and at different angles.

Features

Figure 1

Straight Shaft Trimmer

(Model No. 51975)

Front Handle

Engine

Throttle

Trigger

Curved Shaft

Grass Deflector

Engine

Throttle

Trigger

Curved Shaft Trimmer

(Model No. 51955)

Front Handle

Straight Shaft

Grass Deflector

Knob

On/Stop

Switch

On/Stop

Switch

Choke

Lever

Choke

Lever

Fuel

Cap

Fuel

Cap

Starter

Grip and

Rope

Starter

Grip and

Rope

Grass

Shield

11

Unpacking

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing

list are included.

WARNING:

Do not use this product if any parts on the pack-

ing list are already assembled to your product

when you unpack it. Parts on this list are not as-

sembled to the product by the manufacturer and

require customer installation. Use of a product

that may have been improperly assembled could

result in serious personal injury.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have

carefully inspected and satisfactorily operated the

product.

 If any parts are damaged or missing, please call

1-866-574-9242 (US) or 1-866-574-9243 (Canada) for

assistance.

Packing List

51955 Curved Shaft Trimmer

Upper Shaft (Power Head)

Curved Shaft Attachment

Front Handle

Curved Shaft Grass Deector

Lubricant

Hanger Cap

Operator’s Manual

51975 Straight Shaft Trimmer

Upper Shaft (Power Head)

Straight Shaft Attachment

Front Handle

Straight Shaft Grass Deector

Lubricant

Hanger Cap

Operator’s Manual

Assembly

WARNING:

If any parts are damaged or missing do not

operate this product until the parts are replaced.

Use of this product with damaged or missing

parts could result in serious personal injury.

WARNING:

Do not attempt to modify this product or create

accessories not recommended for use with this

product. Any such alteration or modication is

misuse and could result in a hazardous condition

leading to possible serious personal injury.

WARNING:

To prevent accidental starting that could cause

serious personal injury, always disconnect the

engine spark plug wire from the spark plug

when assembling parts.

12

Connecting the Attachment to the

Upper Shaft

See Figure 2.

WARNING:

Be certain the knob is fully tightened before

operating equipment; check it periodically for

tightness during use to avoid serious personal

injury.

Follow these steps to connect the attachment to the upper

shaft.

1. Loosen the knob by turning it counterclockwise.

2. Remove the end cap from the attachment shaft.

3. Align the button on the attachment shaft with the guide

recess on the upper shaft.

Figure 3

Attaching the Front Handle

See Figure 3.

Follow these steps to attach the front handle.

1. Remove the slotted Torx™ screws to separate the

handle from the handle support.

2. Press the front handle onto the top of the upper shaft, in

the position indicated by the arrow on the shaft, angling

the handle toward the throttle trigger.

3. Place the front handle along the upper shaft to a posi-

tion that allows for comfortable operation.

4. Place the handle support on the bottom of the shaft on

the opposite side of the front handle.

5. Secure the handle with the slotted Torx™ screws using

a T25 Torx driver or at blade screwdriver.

Note: Do not cover any portion of the warning label with

the front handle.

Assembly

Knob

Slotted

Torx

Screw

Front

Handle

Throttle

Trigger

Handle Support

Figure 2

4. Slide the attachment shaft into the upper shaft until the

attachment shaft clicks into place.

Note: You may need to turn the attachment shaft to

properly align the two shafts.

5. Tighten the knob securely by turning it clockwise.

Removing the Attachment from the

Upper Shaft

See Figure 2.

Follow these steps to remove the attachment from the upper

shaft.

1. Loosen the knob by turning it counterclockwise.

2. Push the button while pulling out the attachment.

Button

Attachment

Shaft

Guide

Recess

Upper

Shaft

13

Attaching the Grass Deflector

Attaching the grass deector differs depending on the type

of trimmer: curved shaft or straight shaft.

WARNING:

The line cut-off blade on the grass deector

is sharp. Avoid contact with the blade. Failure

to avoid contact can result in serious personal

injury.

WARNING:

Always attach the grass deector prior to

operating trimmer. Failure to attach the grass

deector may result in debris being thrown at

the operator and result in serious injury.

To Attach the Curved Shaft Grass Deflector

Model No. 51955

See Figure 4.

Follow these steps to attach the curved shaft grass deector.

1. Remove the hex head cap screw, at washer, lock

washer, and wing nut from the grass deector.

2. Press the grass deector onto the bottom of the curved

shaft as shown.

3. Insert the hex head cap screw through the grass deec-

tor bracket.

4. Place the at washer and lock washer on the hex head

cap screw.

5. Place the wing nut on the hex head cap screw and turn

clockwise to secure.

Figure 5

To Attach the Straight Shaft Grass Deflector

Model No. 51975

See Figure 5.

Follow these steps to attach the straight shaft grass deector.

1. Remove the bolt from the grass deector.

2. Insert the tab on the mounting bracket in the slot on the

grass deector.

3. Align the screw hole in the mounting bracket with the

screw hole in the grass deector.

4. Insert the bolt through the mounting bracket and into

the grass deector.

5. Tighten the bolt securely using a at blade screwdriver

or 5/16 in. wrench.

Assembly

Straight Shaft

Grass Deflector

Tab

Slot

Figure 4

Curved Shaft

Grass Deflector

Wing Nut

Line Cut-off

Blade

Lock

Washer

Hex Head

Cap Screw

Flat

Washer

Bracket

Bolt

Grass

Shield

14

Operation

Fueling and Refueling the Trimmer

WARNING:

Gasoline and its vapors are highly ammable

and explosive. To prevent serious personal

injury and property damage, handle it with care.

Keep away from ignition sources and open

ames, handle outdoors only, do not smoke and

wipe up spills immediately.

Fuel Mixture

This product is powered by a 2-cycle engine and requires

pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded

gasoline and 2-cycle engine lubricant in a clean container

approved for gasoline. DO NOT mix quantities larger than

usable in a 30-day period.

WARNING:

Do not allow familiarity with this product to

make you careless. Remember that a careless

fraction of a second is sufcient to inict

serious injury.

WARNING:

Always wear eye protection with side shields

marked to comply with ANSI Z87.1, along with

hearing protection. Failure to do so could result

in objects being thrown into your eyes and other

possible serious injuries.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this tool.

The use of attachments or accessories not rec-

ommended can result in serious personal injury.

WARNING:

Operation of this equipment may create sparks

that can start res around dry vegetation.

A spark arrestor may be required. The op-

erator should contact local re agencies for

laws or regulations relating to re prevention

requirements.

Applications

Use this product for the following applications:

■ Cutting grass, weeds, and light undergrowth

■ Edging along sidewalks and driveways

Recommended fuel: This engine is certied to operate on

unleaded gasoline intended for automotive use.

Note: We recommend you use PowerCare 2-cycle lubricant

(6.4 oz. or 16 oz.) or an equivalent high-quality synthetic

2-cycle lubricant in this product. Mix at 2.6 oz. per gallon

(US).

Do not use automotive lubricant or 2-cycle outboard

lubricant.

HIGH QUALITY 2-CYCLE ENGINE LUBRICANT

GASOLINE LUBRICANT

1.0 gal. (US) (3.8 liter) 2.6 oz. (76 ml)

2.5 gal. (US) (9.5 liter) 6.4 oz. (189 ml)

Filling Tank

■ Clean surface around fuel cap to prevent contamination.

■ Loosen fuel cap slowly by turning counterclockwise. Rest

the cap on a clean surface.

■ Carefully pour fuel into the tank. Avoid spillage.

■ Prior to replacing the fuel cap, clean and inspect the

gasket.

■ Immediately replace fuel cap and hand tighten by turning

clockwise. Wipe up any fuel spillage.

■ Move at least 30 ft. away from refueling area before starting

the product.

Note: It is normal for smoke to be emitted from a new

engine after rst use.

WARNING:

Always shut off engine before fueling. Never

add fuel to a machine with a running or hot

engine. Move at least 30 ft. from refueling site

before starting engine. Do not smoke and stay

away from open ames and sparks. Failure to

safely handle fuel could result in serious per-

sonal injury.

Oxygenated Fuels

DO NOT USE E85 FUEL. IT WILL VOID YOUR WAR-

RANTY.

Note: Fuel system damage or performance problems result-

ing from the use of an oxygenated fuel containing more than

the percentages of oxygenates stated below are not covered

under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume

(commonly referred to as E10) is acceptable. E85 is not.

15

Throttle

Trigger

On/Stop

Switch

Starting the Product

See Figures 6 - 8.

Starting the product differs depending on whether the engine

is cold or warm. Refer to the label on the air lter cover.

To Start a Cold Engine:

Follow these steps to start a cold engine.

1. Lay the product on a at, bare surface.

2. Push the primer bulb approximately eight times.

3. Set the choke lever to FULL.

4. Depress lock-out button and squeeze throttle trigger

fully (thru step 7) and pull starter handle sharply until

engine attempts to start (no more than 4x).

5. Set the choke lever to HALF.

6. Pull starter handle until engine runs, no more than 6

pulls.

7. Set the choke lever to RUN.

Note: In cooler environments, additional pulls of the

starter handle may be required with the choke lever in

the FULL position.

To Start a Warm Engine:

Follow these steps to start a warm engine.

1. Lay the product on a at, bare surface.

2. Push the primer bulb up to eight times.

3. Set the choke lever to RUN.

4. Depress lock-out button and squeeze throttle trigger

fully, pull the starter cord.

Note: If the product does not start, repeat the previous

steps.

Figure 7

Stopping the Product

See Figure 8.

Follow these steps to stop the product.

1. Release the trigger.

2. Press on/stop switch to (STOP) position.

Figure 8

Operation

Figure 6

Lock-out

Button

Starter

Grip and

Rope

Throttle

Trigger

Primer

Bulb

Set Choke to FULL

Set Choke to RUN

On/Stop

Switch

16

To Operate the Straight Shaft Trimmer

(Model No. 51975)

See Figure 10.

Follow these steps to operate the straight shaft trimmer.

1. Start the trimmer.

2. Hold the trimmer at waist level with your right hand

on the throttle trigger and your left hand on the front

handle.

3. Place the product on the right side of your body with

the engine behind and away from your body.

4. Trim grass and weeds in a left-to-right motion with the

line parallel to the ground.

Figure 10

Operation

PROPER OPERATING

POSITION

PROPER OPERATING

POSITION

Operating the Trimmer

Operating the trimmer differs, depending on whether you are

using the curved shaft trimmer or the straight shaft trimmer.

WARNING:

Engine housing may become hot during trimmer

operation. Do not rest or place your arm, hand,

or any body part against the engine housing

during trimmer operation. Only hold the

trimmers as shown in Figure 9 and 10 with all

body parts clear of engine housing. Extended

contact with the engine housing can result in

burns or other injuries.

WARNING:

Always position the unit on the operator’s right

side. The use of the unit on the operator’s left

side will expose the user to hot surfaces and can

result in possible burn injury.

WARNING:

To avoid burns from hot surfaces, never operate

unit with the bottom of the engine above waist

level.

To Operate the Curved Shaft Trimmer

(Model No. 51955)

See Figure 9.

Follow these steps to operate the curved shaft trimmer.

1. Start the trimmer.

2. Hold the trimmer at waist level with your right hand

on the throttle trigger and your left hand on the front

handle.

3. Place the product on the right side of your body with

the engine behind and away from your body.

4. Trim grass and weeds in a right-to-left motion with the

line parallel to the ground.

Figure 9

17

Figure 11

Retaining

Cap

Operation

Cutting Tips

See Figures 12 and 13.

1. Avoid hot surfaces by always keeping the tool away

from your body. (Proper operating position is shown in

Figures 9 and 10.)

2. Keep the trimmer tilted toward the area being cut; this

is the best cutting area.

3. The curved shaft trimmer cuts when passing the unit

from right to left. the straight shaft trimmer cuts when

passing the unit from left to right. This will avoid

throwing debris at the operator. Avoid cutting in the

dangerous area shown in gures 12 and 13.

4. Use the tip of string to do the cutting; do not force

string head into uncut grass.

5. Wire and picket fences cause extra string wear, even

breakage. Stone and brick walls, curbs and wood may

wear string rapidly.

6. Avoid trees and shrubs. Tree bark, wood moldings, sid-

ing and fence posts can easily be damaged by the string.

Figure 12

Figure 13

Curved Shaft Trimmer

Straight Shaft Trimmer

Dangerous

Cutting Area

Direction of

Rotation

Best Cutting

Area

Dangerous

Cutting Area

Direction of

Rotation

Best Cutting

Area

To Advance the Cutting Line

See Figure 11.

Line advance is controlled by tapping the string head on

grass while running engine at full throttle.

 Run engine at full throttle.

 Tap the knob on ground to advance line. The line advances

each time the knob is tapped. Do not hold the knob on the

ground.

Note: The line trimming cut-off blade on the grass deector

will cut the line to the correct length.

Note: If the line is worn too short you may not be able to

advance the line by tapping it on the ground. If so, stop the

engine and manually advance the line.

To advance the cutting line manually:

Stop the engine and disconnect the spark plug wire.

 Push the knob in while pulling on line(s) to manually

advance the line.

18

Operation

Installing Line in Reel-Easy

™

String

Head

See Figures 14 - 15..

Use .095 in./2.4 mm diameter monolament line.

Stop the engine and disconnect the spark plug wire.

Cut one piece of line approximately 25 ft. in length.

Rotate knob on string head until line on knob aligns

with arrows on top of string head.

Insert one end of line into eyelet located on either side

of the string head and push until line comes out through

eyelet on the other side. Continue to push line through

the string head until the middle section of the line is

inside the string head and line outside the string head is

evenly divided on each side.

While holding the string head in one hand with your

other hand, rotate the knob on the string head to

wind the line. If using the 51955 (curved shaft), knob

should be rotated counterclockwise. If using the 51975

(straight shaft), knob should be rotated clockwise. Wind

the line until approximately 8 in. remains protruding

from the string head.

Figure 14

Line

Arrows

Figure 15

Eyelet

Clockwise (51975

straight shaft)

Counterclockwise

(51955 curved shaft)

19

Maintenance

WARNING:

Use only Toro replacement parts when servicing

this product. Use of any other parts could create

a hazard or cause product damage.

WARNING:

Always wear eye protection with side shields

marked to comply with ANSI Z87.1, along with

hearing protection. Failure to do so could result

in objects being thrown into your eyes and other

possible serious injuries.

WARNING:

Before inspecting, cleaning, or servicing the

machine, shut off engine, wait for all moving

parts to stop, and disconnect spark plug wire

and move it away from spark plug. Failure to

follow these instructions can result in serious

personal injury or property damage.

Cleaning the Product

Stop the product before cleaning.

Clean the exterior of the product with a damp cloth.

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

Wipe or scrape the trimmer head and spool area when

they accumulate dirt or clippings.

Scrape debris away from air intake vents on both sides

of engine housing.

CAUTION:

Keeping air intake vents free of grass and debris

prevents engine overheating and possible engine

damage.

Servicing the Product

■ Check and tighten all fasteners. If any part is damaged

or lost, repair it or replace it.

Checking the Fuel Cap

WARNING:

Check for fuel leaks. A leaking fuel cap is a re

hazard and must be replaced immediately. If

you nd any leaks, correct the problem before

using the product. Failure to do so could result

in a re that could cause serious personal injury.

Maintenance

Air Filter

Cover

Knob

The fuel cap contains a non-serviceable lter and check

valve. A clogged fuel lter causes poor engine performance.

If performance improves when the fuel cap is loosened,

the check valve may be faulty or the lter may be clogged.

Replace the fuel cap if necessary.

Cleaning the Air Filter

See Figure 16 and Figure 18.

Clean the air lter as indicated by the maintenance schedule.

Follow these steps to clean the air lter.

1. Stop the trimmer.

2. Remove the spark plug boot.

3. Loosen the air lter cover by turning the knob counter-

clockwise.

4. Remove the air lter cover.

5. Remove the air lter.

6. Clean the air lter with warm soapy water.

7. Rinse the air lter and let it dry completely.

8. Work two drops of oil into the air lter.

9. Replace the air lter (ts only one way).

10. Replace the air lter cover.

11. Tighten the air lter cover by turning the knob clock-

wise.

12. Replace the spark plug boot.

Note: Replace the air lter as indicated by the mainte-

nance schedule.

Figure 16

20

Figure 17

Maintenance

Spark

Arrester

Plate

Muffler

Cover

Muffler

Gasket

Screw(s)

Cover

Screw(s)

Muffler

7. Remove the spark arrester.

8. Replace the old spark arrester with the new one.

9. Reassemble the mufer by reinstalling the plates and

tightening the three screws (torque to 18 in.lb mini-

mum, 22 in.lb. maximum).

10. Reassemble the mufer and mufer cover and attach to

the mufer gasket with the two screws.

11. Reinsert the mufer assembly and tighten two screws to

engine (torque to 60 in.lb minimum, 80 in.lb. maxi-

mum).

12. Reinstall the cover on the tool and fasten with the ve

screws (torque to 16 in.lb minimum, 22 in.lb. maximum).

Note: Do not over-tighten screws.

Replacing the Spark Plug

See Figure 18.

All model numbers included in this manual use a

Champion RCJ4 spark plug. Use an exact replacement and

replace annually.

1. Remove the spark plug boot.

2. Loosen the spark plug by turning it counterclockwise

with a socket.

3. Remove the spark plug.

4. Hand thread the new spark plug, turning it clockwise.

5. Tighten with a socket. (torque to 170 in.lb. minimum,

190 in.lb. maximum. Do not over-tighten).

CAUTION:

Be careful not to cross-thread the spark plug.

Cross-threading will seriously damage the

product.

Figure 18

Spark

Plug

Spark Plug Boot

Replacing the Spark Arrestor

See Figure 17.

WARNING:

Check for fuel leaks. A leaking fuel cap is a re

hazard and must be replaced immediately. If

you nd any leaks, correct the problem before

using the product. Failure to do so could result

in a re that could cause serious personal injury.

Note: Depending on the type of fuel used, the type and

amount of lubricant used, and/or your operating conditions,

the exhaust port, mufer, and/or spark arrestor screen may

become blocked with carbon deposits. If you notice a power

loss with your gas powered tool, you may need to remove

these deposits to restore performance. We highly recom-

mend that only qualied service technicians perform this

service.

The spark arrester may need to be replaced after repeated

use. If replacement is necessary, use Toro part number

000998216.

To replace the spark arrester:

1. Remove the ve screws that hold the cover.

Note: Removing these screws requires the use of a T20

and T25 torx screwdriver.

2. Remove the cover.

3. Remove the two screws holding the mufer assembly in

place.

4. Remove the mufer assembly and mufer gasket. It

may be necessary to work the mufer assembly free

from the mufer gasket.

5. Separate the mufer cover from the mufer.

6. Remove the three screws that hold the plates on the

mufer.

La page charge ...

Toro 17in Curved-Shaft Gas Trimmer Manuel utilisateur

Ce manuel convient également à

Toro 17in Curved-Shaft Gas Trimmer Manuel utilisateur

dans d''autres langues

Documents connexes