Samsung LN-T4061F Manuel utilisateur

Owner’s

Instructions

Register your product at www.samsung.com/global/register

Record your Model and Serial number here for future reference.

· Model __________ · Serial No. ____________

LN-T4061F

LN-T4065F

LN-T4661F

LN-T4665F

LN-T5265F

TFT-LCD TELEVISION

Contact SAMSUNG WORLD-WIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG

customer care center.

Contacte con SAMSUNG WORLD-WIDE

Si tiene alguna pregunta o comentario referente a nuestros productos, por favor contacte con nuestro Servicio de

Atención al Cliente.

Country

Customer Care Center

Web Site Address

CANADA 1-800-SAMSUNG (7267864) www.samsung.com/ca

Samsung Electronics Canada Inc., Customer

Service 55 Standish Court Mississauga,

Ontario L5R 4B2 Canada

Samsung Electronique Canada Inc.,

Service à la Clientèle 55 Standish Court

Mississauga, Ontario L5R 4B2 Canada

U.S.A 1-800-SAMSUNG (7267864) www.samsung.com

Samsung Electronics America, Inc.

105 Challenger Road

Ridgefield Park, NJ 07660-0511

BN68-01178A-00

BN68-01178A-00-Cover.indd 1 2007-02-15 �� 4:34:47

Precautions When Displaying a Still Image

A still image may cause permanent damage to the TV screen

• Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention.

This image retention is also known as "screen burn".

To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

• Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the

left, right and center of the screen caused by the difference of light emission on the screen.

Playing a DVD or a game console may cause a similar effect to the screen.

Damages caused by the above effect are not covered by the Warranty.

• Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images.

To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

Précautions à prendre lors de l’affichage d’une image fixe

Une image fixe peut causer des dommages irrémédiables à l’écran du téléviseur.

• N’affichez pas une image fixe sur l’écran LCD plus de 2 heures. Cela pourrait provoquer une rémanence de l’image à l’écran.

Cette rémanence de l’image est également appelée “brûlure de l’écran”. Pour éviter une telle rémanence de l’image à l’écran,

réduisez la luminosité et le contraste de l’écran lorsque vous laissez une image fixe affichée

• Regarder l’écran LCD du téléviseur en format 4:3 pendant une longue période peut laisser des traces de

bordures à gauche, à droite et au centre de l’écran, à cause de la différence d’émission de lumière sur l’écran.

La lecture d’un DVD ou l’utilisation d’une console de jeu peut avoir un effet similaire sur l’écran. Les dommages

provoqués par les effets qui précèdent ne sont pas couverts par la garantie.

• L’affichage d’images fixes de jeux vidéo et d’ordinateurs pendant plus longtemps qu’une période spécifique peut provoquer des

rémanences.Pour éviter cela, réduisez la “luminosité” et le “contraste” lors de l’affichage d’images fixes.

Important Warranty Information Regarding Television Format Viewing

Wide screen format LCD Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide

screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format,

or expanded to fill the screen if your model offers this feature and the images are constantly moving. Displaying stationary

graphics and images on screen, such as the dark side-bars on nonexpanded standard format television video and

programming, should be limited to no more than 5% of the total television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos,

web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary

images that exceed the above guidelines can cause uneven aging of LCD Displays that leave subtle, but permanent

burned-in ghost images in the LCD picture. To avoid this, vary the programming and images, and primarily display

full screen moving images, not stationary patterns or dark bars.

On LCD models that offer picture sizing features, use these controls to view different formats as a full screen picture.

Be careful in the selection and duration of television formats used for viewing. Uneven LCD aging as a result of format

selection and use, as well as burned-in images, are not covered by your Samsung limited warranty.

U.S.A Only

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain

third parties. In particular, this product is licensed under the following US patents: 5,991,715, 5,740,317, 4,972,484,

5,214,678, 5,323,396, 5,539,829, 5,606,618, 5,530,655, 5,777,992, 6,289,308, 5,610,985, 5,481,643, 5,544,247,

5,960,037, 6,023,490, 5,878,080, and under US Published Patent Application No. 2001-44713-A1.

This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are

granted for commercial use. The license does not cover any product unit other than this product unit and the license

does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or

sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode

audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product

features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

Other countries

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third

parties. This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights

are granted for commercial use. The license does not cover any product unit other than this product unit and the license

does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or

sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode

audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product

features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

Still.indd 1 2007-02-15 �� 9:40:25

English - 1

Contents

English

GENERAL INFORMATION

List of Features ..................................................................2

Accessories .......................................................................2

Viewing the Control Panel ................................................3

Viewing the Connection Panel ..........................................4

Remote Control .................................................................5

Installing Batteries in the Remote Control .........................6

CONNECTIONS

Connecting VHF and UHF Antennas .................................6

Connecting Cable TV ........................................................7

Connecting a VCR .............................................................8

Connecting a Camcorder ..................................................9

Connecting a DVD Player/Set-Top Box .............................9

Connecting a DVD Player/Set-Top Box via HDMI ...........10

Connecting a DVD Player/Set-Top Box via DVI ..............10

Connecting a Digital Audio System .................................11

Connecting an Amplier/DVD Home Theater ..................11

Connecting a PC .............................................................11

OPERATION

Turning the TV On and Off ..............................................12

Plug & Play Feature .........................................................12

Changing Channels .........................................................13

Adjusting the Volume .......................................................14

Viewing the Display .........................................................14

Viewing the Menus ..........................................................15

Memorizing the Channels ................................................15

Setting Up Your Remote Control .....................................17

Remote Control Codes ....................................................19

To Select the Source .......................................................22

To Edit the Input Source Name .......................................22

PICTURE CONTROL

Using Automatic Picture Settings ....................................23

Adjusting the Color Tone .................................................24

Adjusting the Detailed Settings ........................................25

Changing the Screen Size ...............................................28

Setting the Active Color ...................................................29

DNIe (Digital Natural Image engine) ................................29

Freezing the Picture ........................................................30

Setting the Film Mode ......................................................30

HDMI Black Level ............................................................30

Viewing Picture-in-Picture ...............................................31

SOUND CONTROL

Customizing the Sound ...................................................33

Using Automatic Sound Settings .....................................33

Setting the TruSurround XT .............................................34

Choosing a Multi-Channel Sound (MTS) track - Digital ..34

Choosing a Multi-Channel Sound (MTS) track - Analog .35

Automatic Volume Control ...............................................35

Selecting the Internal Mute ..............................................36

Setting the On/Off Melody ...............................................36

Listening to the Sound of the Sub (PIP) Picture ..............37

Resetting the Sound Settings to the Factory Defaults .....37

Connecting Headphones .................................................37

■

CHANNEL CONTROL

Selecting the Antenna ......................................................38

Clearing Scrambled Channels - Digital ............................38

Setting the Channel Lists .................................................39

To set-up Your Favorite Channels ...................................40

Using the Channel Lists ...................................................41

Viewing the Channel Lists ...............................................41

Labeling Channels ...........................................................42

LNA (Low Noise Amplier) ...............................................42

Fine Tuning Analog Channels ..........................................43

Checking the Digital-Signal Strength ...............................43

PC DISPLAY

Using Your TV as a Computer (PC) Display ....................44

Display Modes .................................................................44

Setting up the TV with your PC .......................................45

Setting the Home Theater PC .........................................46

TIME SETTING

Setting the Clock.............................................................. 47

FUNCTION DESCRIPTION

Selecting a Menu Language ............................................50

Setting the Blue Screen Mode .........................................51

Using the Game Mode .....................................................51

Viewing Closed Captions

(On-Screen Text Messages) - Analog ..............................52

Viewing Closed Captions

(On-Screen Text Messages) - Digital ...............................53

Menu Transparency Level ...............................................54

Using the Energy Saving Feature ....................................54

Setting the Function Help ................................................55

Digital Noise Reduction ...................................................55

Using the V-Chip ..............................................................56

Setting the Light Effect

(LN-T4065F / LN-T4665F / LN-T5265F) .........................63

Upgrading the Software ..................................................63

WISELINK

WISELINK .......................................................................64

Using the WISELINK Function ........................................64

Using the WISELINK Menu .............................................65

Using the PHOTO (JPEG) List ........................................66

Using the MP3 List ..........................................................73

Using the Setup Menu .....................................................75

About Anynet+

What is Anynet+?.............................................................77

Connecting Anynet+ Devices...........................................77

Setting Up Anynet+ ..........................................................78

Scanning and Switching between Anynet+ Devices ........78

Recording ........................................................................79

Listening through a Receiver (Home theater) ..................80

Check Points before Requesting Service ........................80

APPENDIX

Troubleshooting ...............................................................81

Installing the Stand ..........................................................83

Disconnecting the Stand ..................................................83

Wall-Mount Adjustment (Sold separately)........................84

Wall Mount Kit Specifications (VESA) .............................85

Using the Anti-Theft Kensington Lock .............................86

Specications ..................................................................87

■

Symbol Press Important Note One-Touch

Button

BN68-01178A-Eng.indd 1 2007-02-15 �� 9:02:57

English - 2

Accessories

Please make sure the following items are included with your LCD TV.

If any items are missing, contact your dealer.

Remote Control & Batteries (AAA x 2)

(BN59-00599A)

Power Cord

(3903-000144)

Cleaning Cloth

(BN63-01798A)

Cover-Bottom

LN-T4061F : BN63-03031A

LN-T4065F : BN63-03298A

LN-T4661F : BN63-03148A

LN-T4665F / LN-T5265F : BN63-03308A

Owner’s Instructions

Warranty Card / Registration

Card / Safety Guide Manual

(Not available in all locations)

The items color and shape may vary depending on the model.

General Information

List of Features

 Adjustable picture settings that can be stored in the TV’s memory.

 Automatic timer to turn the TV on and off.

 A special sleep timer.

 Excellent Digital Interface & Networking :

With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Set-Top/Cable Box needed.

 Remote Control

The supplied remote can be used to operate the TV as well as most DVD players, Set-Top boxes,

Cable Boxes and VCRs.

 Excellent Picture Quality

- DNIe technology provides life-like clear images.

 SRS TruSurround XT

- SRS TruSurround XT provides a virtual Dolby surround system.

BN68-01178A-Eng.indd 2 2007-02-15 �� 8:56:52

English - 3

Viewing the Control Panel

1

1 2 3 4 6

5

2

3

4

567

5

7

Buttons on the Lower-Right Part of the Panel

The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu.

To use the more advanced features, you must use the remote control.

The product color and shape may vary depending on the model.

1

SOURCE

Toggles between all the available input sources

(TV, AV1, AV2, S-Video1, S-Video2, Component1,

Component2, PC, HDMI1, HDMI2, HDMI3).

In the on-screen menu, use this button as you would

use the ENTER button on the remote control.

2

MENU

Press to see an on-screen menu of your TV’s features.

3

- VOL +

Press to increase or decrease the volume.

In the on-screen menu, use the + VOL - buttons as you

 wouldusethe◄and►buttonsontheremotecontrol.

4 CH

Press to change channels.

In the on-screen menu, use the < CH > buttons as you

 wouldusethe▲and▼butonsontheremotecontrol.

5

SPEAKERS

6

(POWER)

Press to turn the TV on and off.

7

POWER INDICATOR

Blinks and turns off when the power is on and

lights up in stand-by mode.

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

<LN-T4061F / LN-T4661F>

<LN-T4065F / LN-T4665F / LN-T5265F>

BN68-01178A-Eng.indd 3 2007-02-16 �� 1:54:32

English - 4

Viewing the Connection Panel

Rear Panel Jacks

Use the rear panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players.

For more information on connecting equipment, see pages 6-11.

1

AUDIO OUT

Connects to the audio input jacks on your Amplifier/

Home theater.

2

DIGITAL AUDIO OUT (OPTICAL)

Connects to a Digital Audio component.

3

PC IN

Connects to the video and audio output jacks on

your PC.

4

HDMI IN 1,2,3 /DVI IN(HDMI1) (AUDIO R/L)

Connects to the HDMI jack of a device with an HDMI output.

Use the HDMI IN 1 jack for a DVI connection to an

external device.

You should use the DVI to HDMI cable or DVI-HDMI

adapter (DVI to HDMI) for a video connection,and the

DVI IN ‘R-AUDIO-L’ jack for audio.

- The HDMI IN 1 jack does not support PC connection

- No sound connection is needed for an HDMI to HDMI

connection

- When using an HDMI/DVI cable connection, you must use

the HDMI IN 1 jack.

5

ANT 1 IN/ANT 2 IN

Connects to an antenna or cable TV system.

6

EX LINK

Connect this to the jack on the optional wall mount

bracket. This will allow you to adjust the TV viewing angle

using your remote control.

7

COMPONENT IN 1,2

Connects Component video/audio.

8

AV IN 1 / AV IN 2

Video and audio inputs for external devices, such as a

camcorder or VCR.

S-VIDEO

Connects an S-Video signal from a camcorder or VCR.

9

POWER INPUT

Connects the supplied power cord

0

KENSINGTON LOCK

The Kensington lock (optional) is a device used to

physically fix the system when used in a public place.

If you want to use a locking device, contact the dealer

where you purchased the TV.

The place of the Kensington Lock may be different

depending on its model.

!

HEADPHONE

Connects a set of external headphones for private

listening.

@

WISELINK

Connect this to the jack on the optional wall mount

bracket. This will allow you to adjust the TV viewing

angle using your remote control.

[Side Panel Jacks]

BN68-01178A-Eng.indd 4 2007-02-15 �� 8:56:54

English - 5

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV. When using the remote, always point it directly at the

TV. You can also use your remote control to operate your VCR, Cable box, DVD player, or Set-Top Box.

This is a special remote control for the visually impaired, and has Braille

points on the Power, Channel, STOP, PLAY/PAUSE and Volume buttons.

The performance of the remote control may be affected by bright light.

1

POWER

Turns the TV on and off.

2

NUMERIC BUTTONS

Press to change the channel.

3

–

Press to select additional channels(digital

and analog) being broadcast by the same

station. For example, to select channel

“54-3”, press “54”, then press “–” and “3”.

4

CH LIST

Used to display Channel Lists on the

screen.

5

ANTENNA

Press to select “AIR” or “CABLE”.

6

VCR/DVD Functions

- Rewind

- Stop

- Play/Pause

- Fast/Forward

7

VOL / VOL

Press to increase or decrease the

volume.

8 (

MUTE)

Press to temporarily cut off the sound.

9

MENU

Displays the main on-screen menu.

0

S.MODE

Press to select the sound mode.

!

RETURN

Returns to the previous menu.

@

P.MODE

Press to select the picture mode.

#

CAPTION

Controls the caption decoder.

$

FAV.CH

Press to switch to your favorite channels.

%

SLEEP

Press to select a preset time interval

for automatic Shut off.

^

SRS

Selects SRS TruSurround XT mode.

&

SET

Sets the remote to control your

TV, VCR, Cable, DVD, or Set-Top Box

*

TV, DVD, STB, CABLE, VCR

Press to operate your TV,DVD, STB,

CABLE (box), or VCR

(See pages 17-21)

(

When pressing this button, a number

of buttons on the remote control (e.g.

TV, DVD, STB, CABLE, VCR,

VOL and CH buttons) light up for a few

seconds and then turn off to save

power. This function is convenient for

using the remote at night or when dark.

)

SOURCE

Press to display all of the available

video sources.

a

PRE-CH

Tunes to the previous channel.

b

WISELINK

This function enables you to view and

play photo (JPEG) and audio files

(MP3) from an external device.

(Refer to page

65)

c

REC

This remote can be used to control

recording on Samsung recorders.

(Refer to page 79)

d

CH

/ CH

Press to change channels.

e

EXIT

Press to exit the menu.

f

UP▲ / DOWN▼ / LEFT◄

/

RIGHT►

/ ENTER

Use to select on-screen menu items

and change menu values.

g

INFO

Press to display information on the TV

screen.

h

Anynet+

Runs the Anynet+ functions and sets

up Anynet devices.

i

STILL

Press to stop the action during a

particular scene.

Press again to resume normal video.

j

P.SIZE

Picture size selection.

k

PIP

Picture-in Picture ON/OFF.

l

CH

/

Displays the available channels in

sequence. (These buttons change

channels in the PIP window only.)

m

MTS

Press to choose stereo, mono or

Separate Audio Program

(SAP broadcast).

n

RESET

When your remote does not work,

change the batteries and press the

RESET button for 2-3 seconds before

use.

BN68-01178A-Eng.indd 5 2007-02-15 �� 8:56:55

English - 6

1. Lift the cover at the back of the remote control upward as shown in the figure.

2. Install two AAA size batteries.

Make sure to match the "+" and "–" ends of the batteries with the diagram inside the compartment.

3. Replace the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a

long time.

The remote control can be used up to about 23 feet from the TV.

(Assuming typical TV usage, the batteries should last for about one year.)

If the remote control doesn’t work, check the following:

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage, or is the power cord unplugged?

5. Is there a special fluorescent light or neon sign nearby?

Installing Batteries in the Remote Control

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like the diagram to the right, see "Antennas with

300 Ω Flat Twin Leads" below.

If your antenna has one lead that looks like the diagram to the right, see "Antennas with 75

Ω Round Leads".

If you have two antennas, see "Separate VHF and UHF Antennas".

1. Place the wires from the twin leads under the screws on a 300-75 Ω adapter

(not supplied).

Use a screwdriver to tighten the screws.

2. Plug the adaptor into the ANT 2 IN (CABLE) terminal on the back of the TV.

ANT 2 IN

(CALBE)

Antennas with 300 Ω Flat Twin Leads

If you are using an off-air antenna (such as a roof antenna or "rabbit ears") that has 300 Ω twin at leads, follow the directions

below.

1. Plug the antenna lead into the ANT 1 IN (AIR) terminal on the back of the TV.

Antennas with 75 Ω Round Leads

ANT 1 IN

(AIR)

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before con-

necting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

1. Connect both antenna leads to the combiner.

2. Plug the combiner into the ANT 1 IN (AIR) terminal on the bottom of the rear panel.

UHF

VHF

ANT 1 IN

(AIR)

UHF

VHF

Connections

BN68-01178A-Eng.indd 6 2007-02-15 �� 8:56:56

English - 7

After you have made this connection, set the A/B switch to the "A" position for normal viewing. Set the A/B switch to the "B" position to

view scrambled channels. (When you set the A/B switch to "B", you will need to tune your TV to the cable box’s output channel, which is

usually channel 3 or 4.)

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-

way splitter, an RF (A/B) switch, and four lengths of RF cable. (These items are available at most electronics stores.)

2. Connect this cable to a two-way splitter.

3. Connect an RF cable between the OUTPUT

terminal on the splitter and the IN terminal

on the cable box.

4. Connect an RF cable between the

ANT OUT terminal on the cable box and

the B–IN terminal on the RF(A/B) switch.

1. Find and disconnect the cable that is

connected to the ANT IN terminal on your

cable box.

This terminal might be labeled "ANT IN",

"VHF IN" or simply, "IN".

5. Connect another cable between the other

OUT terminal on the splitter and the A–IN

terminal on the RF (A/B) switch.

6. Connect the last RF cable between the

OUT terminal on the RF (A/B) switch and

the ANT IN terminal on the rear of the TV.

Splitter

Incoming

cable

Splitter

Cable Box

Incoming

cable

Splitter

Cable Box

RF (A/B)

Switch

Incoming

cable

ANT IN

Splitter

Cable Box

Incoming

cable

RF (A/B)

Switch

Splitter

Cable Box

Incoming

cable

TV Rear

RF (A/B)

Switch

ANT IN

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

1. Plug the incoming cable into the ANT 2 IN (CABLE) terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.

Connecting to a Cable Box that Descrambles All Channels

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled "ANT OUT", "VHF OUT" or simply, "OUT".

2. Connect the other end of this cable to the ANT 2 IN (CABLE) terminal on the back of the TV.

ANT OUT

ANT IN

ANT 2 IN

(CABLE)

ANT 2 IN

(CABLE)

BN68-01178A-Eng.indd 7 2007-02-15 �� 8:56:58

English - 8

Connecting a VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the

instructions on pages 6-7). Skip step 1 if you have not yet connected to an antenna or a cable system.

1. Unplug the cable or antenna

from the back of the TV.

2. Connect the cable or antenna

to the ANT IN terminal on the

back of the VCR.

3. Connect an RF Cable between

the ANT OUT terminal on the

VCR and the ANT 1 IN (AIR) or

ANT 2 IN (CABLE) terminal on

the TV.

4. Connect a Video Cable

between the VIDEO OUT jack

on the VCR and the AV IN 1

(or AV IN 2) [VIDEO] jack on

the TV.

5. Connect Audio Cables

between the AUDIO OUT

jacks on the VCR and the

AV IN 1 (or AV IN 2)

[R-AUDIO-L] jacks on the TV.

If you have a “mono”

(non-stereo) VCR, use a

Y-connector (not supplied)

to hook up to the right

and left audio input jacks

of the TV. If your VCR

is stereo, you must

connect two cables.

Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.

Each VCR has a different back panel configuration.

When connecting a VCR, match the color of the connection terminal to the cable.

TV Rear Panel

RF Cable (Not supplied)

3

VCR Rear Panel

2

Video Cable (Not supplied)

4

Audio Cable (Not supplied)

5

Your Samsung TV can be connected to an S-Video signal from an VCR.

(This connection delivers a better picture as compared to a standard VCR.)

1. To begin, follow steps 1–3

in the previous section to

connect the antenna or

cable to your VCR and

your TV.

2. Connect an S-Video Cable

between the S-VIDEO OUT

jack on the VCR and the

AV IN1 [S-VIDEO] jack on

the TV.

3. Connect Audio Cables

between the AUDIO OUT

jacks on the VCR and the

AV IN1 [R-AUDIO-L] jacks

on the TV.

An S-Video cable may be included with a VCR. (If not, check your local electronics store.)

Each VCR has a different back panel configuration.

When connecting a VCR, match the color of the connection terminal to the cable.

VCR Rear Panel

RF Cable (Not supplied)

1

Audio Cable (Not supplied)

3

TV Rear Panel

S-Video Cable (Not supplied)

2

Video Connection

S-Video Connection

ANT 1 IN

(AIR)

ANT 2 IN

(CABLE)

BN68-01178A-Eng.indd 8 2007-02-15 �� 8:56:59

English - 9

Connecting a DVD Player or Set-Top/Cable Box

The rear panel jacks on your TV make it easy to connect a DVD player or Set-Top/Cable box to your TV.

1. Connect a Component

Cable between the

COMPONENT IN(1 or 2)

[Y, PB, PR] jacks on the TV

and the COMPONENT

[Y, PB, PR] jacks on the

DVD player or Set-Top/Cable

Box.

2. Connect Audio Cables

between the COMPONENT

IN(1 or 2) [R-AUDIO-L]

jacks on the TV and the

AUDIO OUT jacks on the

DVD player or Set-Top/Cable

Box.

Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and

Pr (Red) for enhanced video quality.

Be sure to match the component video and audio connections.

For example, if connecting the video cable to COMPONENT IN, connect the audio cable

to COMPONENT IN also.

Each DVD Player and Set-Top/Cable box has a different back panel configuration.

When connecting a DVD player or Set-Top/Cable box, match the color of the connection

terminal to the cable.

DVD Player or Set-Top/Cable Box

TV Rear Panel

Component Cable (Not supplied)

1

Audio Cable (Not supplied)

2

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV.

They allow you to view the camcorder tapes without using a VCR

1. Connect a Video Cable

between the AV IN2

[VIDEO] jack on the

TV and the VIDEO OUT

jack on the camcorder.

2. Connect Audio Cables

between the AV IN2

[R-AUDIO-L] jacks on the

TV and the AUDIO OUT

jacks on the camcorder.

Camcorder

TV Side Panel

Video Cable (Not supplied)

1

Audio Cable (Not supplied)

2

Each Camcorder has a different back panel configuration.

When connecting a Camcorder, match the color of the connection terminal to the cable.

BN68-01178A-Eng.indd 9 2007-02-15 �� 8:57:00

English - 10

Connecting a DVD Player or Set-Top/Cable Box via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.

DVD Player, Set-Top/Cable Box Rear Panel

TV Rear Panel

HDMI Cable (Not supplied)

What is HDMI?

• HDMI(High-Definition Multimedia Interface), is an interface that

enables the transmission of digital audio and video signals using a single cable

• The difference between HDMI and DVI is that the HDMI device is smaller in size and

has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed

Each DVD player and or Set-Top/Cable box has a different back panel configuration.

Connecting a DVD Player or Set-Top/Cable Box via DVI

This connection can only be made if there is a DVI Output connector on the external device.

Each DVD player and Set-Top/Cable Box has a different back panel configuration.

When connecting a DVD player or Set-Top/Cable Box, match the color of the connection terminal

to the cable.

When using an HDMI/DVI cable connection,you must use the HDMI IN1 jack.

TV Rear Panel

DVD Player, Set-Top Box

Audio Cable (Not supplied)

2

DVI to HDMI Cable (Not supplied)

1

1. Connect an HDMI Cable

between the HDMI IN

(1,2 or 3) jack on the

TV and the HDMI jack

on the DVD player or Set-

Top/Cable Box.

1. Connect a DVI to HDMI

Cable or DVI-HDMI Adapter

between the HDMI IN 1

jack on the TV and

the DVI jack on the

DVD player or Set-Top/Cable

Box.

2. Connect Audio Cables

between the DVI IN (HDMI 1)

[R-AUDIO-L] jack on the

TV and the AUDIO OUT jacks

on the DVD player or

Set-Top/Cable Box.

Side Panel Jacks

or

BN68-01178A-Eng.indd 10 2007-02-15 �� 8:57:01

Connecting an Amplier/DVD Home Theater

1. Connect Audio Cables

between the AUDIO OUT

[R-AUDIO-L] on the TV

and AUDIO IN [R-AUDIO-

L] on the Amplifier/DVD

Home Theater.

When an audio amplifier is

connected to the "AUDIO

OUT [L-AUDIO-R]"

terminals: Decrease the

volume of the TV, and adjust

the volume level with the

Amplifier’s volume control.

Amplier/DVD Home Theater

TV Rear Panel

Audio Cable (Not supplied)

Each Amplifier/DVD Home Theater has a different back panel configuration.

When connecting an Amplifier/DVD Home Theater, match the color of the connection

terminal to the cable.

English - 11

Connecting a Digital Audio System

1. Connect an Optical Cable

between the “DIGITAL

AUDIO OUT (OPTICAL)”

jacks on the TV and the

Digital Audio Input jacks on

the Digital Audio System.

When a Digital Audio

System is connected to the

“DIGITAL AUDIO OUT

(OPTICAL)” terminal:

Decrease the volume

of the TV, and adjust the

volume level with the

system’s volume control.

Digital Audio System

TV Rear Panel

Optical Cable (Not supplied)

5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.

Each Digital Audio System has a different back panel configuration.

The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV.

Connecting a PC

PC

TV Rear Panel

D-Sub Cable (Not supplied)

1

PC Audio Cable (Not supplied)

2

1. Connect a D-Sub

Cable between PC IN

[PC] connector on

the TV and the PC

output connector on

your computer.

2. Connect a PC Audio

Cable between PC IN

[AUDIO] jack on the

TV and the Audio Out

jack of the sound card

on your computer.

Each PC has a different back panel configuration.

When connecting a PC, match the color of the connection terminal to the cable.

When using an HDMI/DVI cable connection,you must use the HDMI IN1 terminal.

1Streo/2RCA Cable (Not supplied)

2

HDMI/DVI Cable (Not supplied)

1

Using the D-Sub Cable

Using the HDMI/DVI Cable

TV Rear Panel

Using the D-Sub Cable

1.

Connect a HDMI/DVI

cable between the

HDMI1/DVI IN jack on

the TV and the PC output

jack on your computer.

2.

Connect a 1Stereo/2RCA

cable between the DVI

IN [L-AUDIO-R] jack on

the TV and the Audio Out

jack of the sound card on

your computer.

Using the HDMI/DVI Cable

PC

BN68-01178A-Eng.indd 11 2007-02-15 �� 10:31:43

English - 12

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently:

1. Press the POWER button on the remote control.

The message “Menu language, Shop Mode, Channels and Time will be set.” is

displayed.

Press the ENTER

button, then “Select the language of the OSD” menu

is automatically displayed.

2. Press the ▲ or ▼ buttons to select language, then press the ENTER button.

The message “Select Home Mode when installing this TV at home.” is displayed.

3. Press the ◄ or ► buttons to select “Shop” or “Home”, then

press the ENTER button.

The message “Select the antennas to memorize.” is displayed.

We recommend setting the TV to Home mode for the best picture in your

home environment.

Shop mode is only intended for use in retail environments.

If the unit is accidentally set to Shop mode and you want to return to Dynamic

(Home) mode, press any Volume button and then hold down the MENU button

for five seconds on the side panel of the TV.

4. Press the ▲ or ▼ buttons to memorize the channels of the selected connection.

Press the ENTER button to select “Start”.

If the antenna is connected to ANT 1(AIR), select “Air” and if it is connected to

ANT 2 (CABLE), select “Cable”.

If both ANT 1 (AIR) and ANT 2 (CABLE) are connected, select the “Air + Cable”.

In Cable mode, you can select the correct signal source among STD, HRC,

and IRC by pressing the ▲ or ▼ button, then press the ENTER button.

Contact your local cable company to identify the type of cable system that

exists in your particular area.

5. The TV will begin memorizing all of the available channels.

After all the available channels are stored, the Auto program menu reappears.

Press the ENTER button when channel memorization is complete.

The message “Select the clock mode.” is displayed.

To stop the search before it has finished, press the ENTER button with stop

selected.

6. Press the ENTER button.

Press the ▲ or ▼ buttons to select “Manual” or “Auto”, then Press the

ENTER button.

The message “Set to daylight savings time.” is displayed.

Turning the TV On and Off

Press the POWER button on the remote control.

You can also use the button on the front of the panel.

Operation

Select Home Mode when installing this TV at home.

Plug & Play

Clock Set

Menu Language :

Plug & Play

English

Español

Français

Move Enter Skip

Shop

Menu language, Shop Mode,

Channels and Time will be set.

Start

Select the language of the OSD.

Home

Move Enter Skip

Select the antennas to memorize.

Start

Air

Plug & Play

Cable

Air+Cable

Start

Move Enter Skip

Clock Mode :

Move Enter Skip

Select the clock mode.

Plug & Play

Manual

Auto

35%

Stop

Enter Skip

Auto Program in progress.

Air Channel 50

Plug & Play

Auto Program is incomplete.

16 Channels were memorized.

Air : 16, Cable : 0.

Enter Skip

OK

BN68-01178A-Eng.indd 12 2007-02-15 �� 8:57:05

English - 13

7. Press the ▲ or ▼ buttons to select “No” or “Yes”, then press the ENTER button.

The message “Select the time zone in which you live.” is displayed.

8. Press the ▲ or ▼ buttons to highlight the time zone for your local area

Press the ENTER button. If you have received a digital signal, the time will be set

automatically.

If not, see page 48 to set the clock.

9. The message “Enjoy your watching.” is displayed.

When you have finished, press the ENTER button.

Changing Channels

1. Press the CH

or

CH

button to change channels.

When you press the CH

or

CH

button, the TV changes channels in

sequence.

You will see all the channels that the TV has memorized. (The TV must have

memorized at least three channels). You will not see channels that were either

erased or not memorized. See page 16 to memorize channels.

If you want to reset this feature...

1. Press the MENU

button to display the menu.

Press the ▲ or ▼ buttons to select "Setup", then press the ENTER button.

2. Press the ENTER button again, to select "Plug & Play".

3. The message “Menu language, Shop Mode, Channels and Time will be set.”

is displayed.

Using the Channel Buttons

1. Press the PRE-CH button.

The TV will switch to the last channel viewed.

To quickly switch between two channels that are far apart, tune to one

channel, then use the number button to select the second channel. Then

use the PRE-CH button to quickly alternate between them.

Using the PRE-CH Button to select the Previous Channel

Daylight Savings Time :

Set the daylight savings time.

Plug & Play

No

Yes

Select the time zone in which you live.

Plug & Play

Newfoundland

Atlantic

Eastern

Central

Mountain

Pacific

Alaska

Hawaii

Enjoy your watching.

OK

Setup

Plug & Play ►

Language : English ►

Time

►

Game Mode : Off ►

V-Chip ►

Caption ►

Menu TransParency : High ►

▼More

TV

Move Enter Return

Menu language, Shop Mode,

Channels and Time will be set.

Start

Move Enter Exit

BN68-01178A-Eng.indd 13 2007-02-15 �� 8:57:07

English - 14

Adjusting the Volume

1. Press the

VOL

or VOL

buttons to decrease or increase the volume.

Using Mute

At any time, you can cut off the sound using the MUTE button.

1. Press MUTE button and the sound cuts off.

The word " " will appear in the lower-left corner of the screen.

2. To turn mute off, press the MUTE button again, or simply press the

VOL

or VOL

buttons.

Viewing the Display

1. Press the INFO button on the remote control.

The TV will display the channel, the type of sound,

and the status of certain picture and sound settings.

Press the INFO button once more or wait approximately 10 seconds and the

display disappears automatically.

The display identies the current channel and the status of certain audio-video settings.

Air 7

Mono

Picture Mode : Dynamic

Sound Mode : Custom

MTS : Stereo

05 : 54 pm

BN68-01178A-Eng.indd 14 2007-02-15 �� 8:57:08

English - 15

Viewing the Menus

1. With the power on, press the MENU button.

The main menu appears on the screen. The menu’ s left side has five icons:

Picture, Sound, Channel, Setup, Input.

2. Use the ▲ or ▼ buttons to select one of the five icons.

Then press the ENTER

button to access the icon’s sub-menu.

3. Press the EXIT button to exit.

The on-screen menus disappear from the screen after about one minute.

Input

Source List : TV ►

Edit Name

►

WiSELINK

►

Anynet+ (HDMI-CEC)

TV

Move Enter Exit

Memorizing the Channels

Your TV can memorize and store all of the available channels for both "off-air" (Air) and "Cable" channels. After the available

channels are memorized, use the CH

or

CH

buttons to scan through the channels. This eliminates the need to change

channels by entering the channels digits. There are three steps for memorizing channels: selecting a broadcast source,

memorizing the channels (automatic) and adding or deleting channels (Channel Lists).

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must specify the

type of signal source that is connected to the TV (i.e. an Air or a Cable system).

1. Press the MENU button to display the menu.

Press the ▲ or ▼ buttons to select "Channel", then press the ENTER

button.

2. Press the ENTER button select “Antenna”.

Press the ▲ or ▼ buttons to select “Air” or “Cable”, then press the ENTER button.

Press the EXIT

button to exit.

Antenna : Air ►

Auto Program

►

Clear Scrambled Channel

►

Channel List

►

Name

►

Fine Tune

►

Signal Strength

►

LNA : On

►

Channel

Move Enter Return

TV

Channel

Move Enter Return

TV

Antenna : Air

Auto Program

Clear Scrambled Channel

Channel List

Name

Fine Tune

Signal Strength

LNA : On

Air

Cable

BN68-01178A-Eng.indd 15 2007-02-15 �� 8:57:10

English - 16

Storing Channels in Memory (Automatic Method)

1. Press the MENU button to display the menu.

Press the ▲ or ▼ buttons to select “Channel”, then press the ENTER button.

2. Press the ▲ or ▼ buttons to select "Auto Program", then press the ENTER

button.

3. Press the ▲ or ▼ buttons to select the antenna connection, then press the

ENTER button.

Air: “Air” antenna signal. / Cable: “Cable” antenna signal. /

Air+Cable: “Air” and “Cable” antenna signals.

4. When selecting the Cable TV system : Press the ENTER button to start the auto

program. By default, the cable TV system is set to “STD”. If you want to select

another type of cable system, press the ▲ or ▼ button to select

“STD”, “HRC” or “IRC”.

STD, HRC and IRC identify various types of cable TV systems. Contact your

local cable company to identify the type of cable system that exists in your

particular area. At this point the signal source has been selected.

Press the ENTER

button to start the auto program.

To stop the search before it has finished, press the ENTER button with stop

selected.

5. After all the available channels are stored, the “Auto Program” menu reappears.

Press the EXIT button to exit.

Move Enter Return

Select the antennas to memorize.

Channel

Move Enter Return

TV

Start

Air

Cable

Air+Cable

Start

Auto Program

Cable Channel 50

50%

Stop

Enter Return

Auto Program in Progress.

Move Enter Return

Selects a cable system.

Auto Program

Move Enter Return

TV

Analog

Start

STD

HRC

IRC

Digital

STD

HRC

IRC

Antenna : Air ►

Auto Program

►

Clear Scrambled Channel

►

Channel List

►

Name

►

Fine Tune

►

Signal Strength

►

LNA : On

►

Channel

Move Enter Return

TV

Plug & Play

Enter Return

Auto Program is complete.

16 Channels were memorized.

Air : 16,

Cable : 0.

OK

BN68-01178A-Eng.indd 16 2007-02-15 �� 8:57:12

English - 17

After the television has been set up properly, your remote control can operate in five

different modes: TV, DVD, Cable, Set-Top Box, VCR. Pressing the corresponding button

on the remote control allows you to switch between these modes, and control

whichever piece of equipment you choose.

The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and

Set-Top Boxes.

Setting Up the Remote to Operate Your VCR

1. Turn off your VCR.

2. Press the VCR

button on your TV’s remote control.

3. Press the SET

button on your TV’s remote control.

4. Using the number buttons on your remote control, enter three digits of the VCR code

listed on page 19 of this manual for your brand of VCR. Make sure you enter three digits

of the code, even if the first digit is a “0”.

(If more than one code is listed, try the first one.)

5. Press the POWER button on the remote control.

Your VCR should turn on if your remote is set up correctly.

If your VCR does not turn on after set up, repeat steps 2, 3, and 4, but try one of the

other codes listed for your brand of VCR.

If no other codes are listed, try each VCR code, 000 through 080.

Note on Using Remote Control Modes: VCR

When your remote control is in “VCR” mode, the volume buttons still control your

TV’s volume.

Setting Up the Remote to Operate Your Cable Box

1. Turn off your cable box.

2. Press the CABLE

button on your TV’s remote control.

3. Press the SET

button on your TV’s remote control.

4. Using the number buttons on your remote control, enter three digits of the cable box code

listed on page 20 of this manual for your brand of cable box. Make sure you enter three

digits of the code, even if the first digit is a “0”. (If there is more than one code listed, try

the first one.)

5. Press the POWER button on the remote control.

Your cable box should turn on if your remote is set up correctly.

If your cable box does not turn on after set up, repeat steps 2, 3, and 4, but try one of the

other codes listed for your brand of cable box. If no other codes are listed, try each code,

000 through 046.

Note on Using Remote Control Modes: Cable Box

When your remote control is in “CABLE” mode, the volume buttons still control your

TV’s volume.

Setting Up Your Remote Control

BN68-01178A-Eng.indd 17 2007-02-15 �� 8:57:13

English - 18

Setting Up the Remote to Operate Your DVD

1. Turn off your DVD.

2. Press the DVD

button on your TV’s remote control.

3. Press the SET

button on your TV’s remote control.

4. Using the number buttons on your remote control, enter three digits of the DVD code

listed on page 20~21 of this manual for your brand of DVD.

Make sure you enter three digits of the code, even if the first digit is a “0”.

(If there is more than one code listed, try the first one.)

5. Press the POWER button on the remote control.

Your DVD should turn on if your remote is set up correctly.

If your DVD does not turn on after set up, repeat steps 2, 3, and 4, but try one of the

other codes listed for your brand of DVD.

If no other codes are list-ed, try each code, 000 through 141.

Note on Using Remote Control Modes: DVD

When your remote control is in “DVD” mode, the volume buttons still control your

TV’s volume.

Setting Up the Remote to Operate Your STB

1. Turn off your STB.

2. Press the STB

button on your TV’s remote control.

3. Press the SET

button on your TV’s remote control.

4. Using the number buttons on your remote control, enter three digits of the STB code

listed on page 21 of this manual for your brand of STB.

Make sure you enter three digits of the code, even if the first digit is a “0”.

(If there is more than one code listed, try the first one.)

5. Press the POWER button on the remote control.

Your STB should turn on if your remote is set up correctly.

If your STB does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other

codes listed for your brand of STB.

(If no other codes are listed, try each code, 000 through 074.)

Note on Using Remote Control Modes: STB

When your remote control is in “STB” mode, the volume buttons still control your

TV’s volume.

BN68-01178A-Eng.indd 18 2007-02-15 �� 8:57:13

La page charge ...

Samsung LN-T4061F Manuel utilisateur

Samsung LN-T4061F Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents