Whirlpool WDF130PAHS Guide d'installation

INSTALLATION INSTRUCTIONS

UNDERCOUNTER DISHWASHER

PLASTIC TUB

INSTRUCCIONES DE INSTALACIÓN

LAVAVAJILLAS EMPOTRADA

CON TINA PLÁSTICA

INSTRUCTIONS D’INSTALLATION

LAVE-VAISSELLE ENCASTRÉ

CUVE EN PLASTIQUE

Table of Contents ........................................................2

Indice ........................................................................27

Table des matières ....................................................51

W10806908C

2

TABLE OF CONTENTS

DISHWASHER SAFETY ................................................... 3

INSTALLATION REQUIREMENTS ................................... 4

Tools and Parts .........................................................................4

Location Requirements ............................................................. 6

Product and Cabinet Opening Dimensions ..............................7

Drain Requirements ..................................................................8

Water Supply Requirements .....................................................8

Electrical Requirements ............................................................8

INSTALLATION INSTRUCTIONS ..................................... 9

Prepare Cabinet Opening – New Utilities .................................9

Install Optional Moisture Barrier ...............................................9

Electrical Connection .............................................................. 10

Prepare Dishwasher ................................................................11

Remove Access Panel ............................................................11

Connect Water Line to Fill Valve .............................................12

Connect Fill Hose to Fill Valve ................................................13

Drain Hose Connection ..........................................................14

Power Cord Connection .........................................................14

Install Door Handle .................................................................16

Place Dishwasher in Cabinet ..................................................16

Choose Anchor Attachment Method ......................................17

Final Installation Check ...........................................................18

Secure Dishwasher in Cabinet Opening .................................19

Direct Wire Connection ...........................................................20

Connect Water Line to House Shut-off Valve .........................22

Connect Drain Hose ..............................................................22

Complete Installation ..............................................................24

Install Access Panel ................................................................ 25

Check Operation .....................................................................26

If Dishwasher Does Not Operate ............................................26

Additional Tips ........................................................................26

3

DISHWASHER SAFETY

You Need to:

■ Slowly open dishwasher door while someone grasps the rear

of the dishwasher. Remove shipping materials and drain hose.

Close dishwasher door until latched.

NOTE: Each dishwasher is tested at the factory and may

contain some residual water in the tub as a result of the test.

■ Observe all governing codes and ordinances.

■ Install this dishwasher as speciﬁed in these instructions.

■ Installation should be performed by a qualiﬁed

service technician.

■ The dishwasher must be installed to meet all electrical

and plumbing national and local codes and ordinances.

Care shall be exercised when the appliance is installed

or removed to reduce the likelihood of damage to the

power cord.

WARNING: To reduce the risk of electric shock, ﬁre, or injury

to persons, the installer must ensure that the dishwasher is

completely enclosed at the time of installation.

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

4

INSTALLATION REQUIREMENTS

TOOLS AND PARTS

Gather the recommended tools and parts before starting

installation. Read and follow the instructions provided with

any tools listed here.

All Installations

Tools Needed:

Pliers Flat-blade screwdriver

Phillips screwdriver Utility knife

5

/

16

" and

1

/

4

" nut drivers or

hex sockets

Small level

Measuring tape or ruler

5

/

8

" open-end wrench

10" adjustable wrench that

opens to 1

1

/

8

" (29 mm)

Torx

®†

T20

®

screwdriver

Other Useful Items You May Need:

Flashlight Shallow pan

Bath towel Masking or duct tape

Parts Supplied:

Drain hose clamps (2)

(1 large/red and 1 small/green)

Drain hose

#10 x

1

/

2

" Phillips-head

screws (2)

Undercounter mounting

brackets (2)

Make sure all these parts are included in the literature package.

If parts are not included, call us at our toll-free number or visit

our website listed in the User Guide.

Door handle (on some models)

†

®

TORX and T20 are registred trademarks of Acument Intellectual Properties, LLC.

5

Other Parts Needed (not provided):

3

/

8

" Compression x

3

/

4

" Hose

Fitting with rubber seal and

90° elbow (required to properly

connect household water line

to the dishwasher) (Whirlpool

Part Number W10685193)

Household Wiring (Metallic)

Strain Relief to ﬁt

7

/

8

" (22 mm)

hole (required to properly

secure household wiring to

the dishwasher terminal box)

(Whirlpool Part

Number 4396672)

NOTE: Use only UL Listed/

CSA Approved part.

Twist-On Wire Connectors

NOTES:

■ Conﬁrm proper size for

connecting your gauge of

household wiring to the

16-gauge wiring in the

dishwasher.

■ Use only UL Listed/CSA

Approved parts.

Call us at our toll-free number, visit our website listed in the User

Guide for part numbers above, or see local electrical/plumbing

supply retailer for equivalent.

Optional Accessory Parts Available:

Moisture Barrier Tape

NOTE: Moisture barrier tape

is recommended if installing a

dishwasher under a wooden

countertop (Whirlpool Part

Number 4396277).

Side Panel Kit

For enclosing the side of the

dishwasher when installing it

at the end of your cabinetry

(Whirlpool Part Number varies

with color.)

Call us at our toll-free number or visit our website listed in the

User Guide for part numbers above.

First-Time Installations

Check local codes. Check existing electrical supply. See the

“Electrical Requirements” section. It is recommended that

electrical connections be made by a licensed electrical installer.

Additional Tools Needed:

Small tubing cutter Wire stripper

Cordless drill with

1

/

2

",

3

/

4

", and 1

1

/

2

" hole saw bits

Additional Parts Needed (not provided):

Copper Tubing (

3

/

8

" O.D.

suggested) or Flexible

Braided Water Supply Line

Kit (Whirlpool Part Number

W10278635RP). Kit includes

braided hose and

3

/

8

"

compression x

3

/

4

" hose ﬁtting.

Screw-Type Clamps 1

1

/

2

"-2"

(38mm-50 mm) (3 maximum)

Optional – Longer Drain Hose

Maximum length 12 ft (3.7 m)

(Whirlpool Part Number 3385556

)

NOTE: Must meet AHAM/IAPMO

test standards, ﬁt 1" (25 mm)

drain connection, and be

resistant to heat and detergent

Call us at our toll-free number, visit our website listed in the

User Guide for part numbers above, or see local plumbing

supply retailer for equivalent.

NOTE: If using a ﬂexible braided hose, replace inlet hose

after 5 years to reduce the risk of hose failure. Record

hose installation or replacement dates on the hose for

future reference.

6

For Direct Wire For Power Cord

Cabinet G

rommet

For 1

1

/

2

" (38 mm) hole

in cabinet (Whirlpool

Part Number 302797)

NOTE: Required for metal

cabine

ts

Power Cord Ki

t

Kit typically includes

power cord, metallic strain

relief, grommet, and twist-on

wi

re connectors (Whirlpool

Part Number 4317824).

Call us at our toll-free number, visit our website listed in the User

Guide for part numbers above, or see local electrical supply

retailer for equivalent.

LOCATION REQUIREMENTS

Dishwasher must be fully enclosed (top, sides, back, and ﬂoor)

upon installation. A side panel kit is available from your dealer

for installing your dishwasher at the end of your cabinetry.

An optional moisture barrier accessory is also available for

installing underneath a wooden countertop. See the “Tools

and Parts” section at the front of the guide for part details

and orders.

Check location where dishwasher will be installed. The location

must provide:

■ Convenient access for loading and unloading dishes. Corner

locations require a 2" (51 mm) minimum clearance between

the side of the dishwasher door and the wall or cabinet.

■ Easy access to water, electricity, and drain:

■ Grounded electrical supply is required.

■ This dishwasher has a water-heating feature and also

requires a connection to a hot water supply line.

■ Make sure pipes, wires, and drain hose are within the

shaded area shown in the “Product and Cabinet Opening

Dimensions” section.

■ Do not run drain lines, water lines, or electrical wiring where

they can interfere with or contact dishwasher motor or legs.

■ Shelter dishwasher and water lines leading to dishwasher

against freezing. Damage from freezing is not covered by

the warranty.

NOTE: If dishwasher will be left unused for a period of time

or in a location where it may be subject to freezing, have it

winterized by authorized service personnel.

■ If installed in new construction, ﬂush the water supply line

of debris before connecting it to the ﬁll valve. If it is not

ﬂushed, debris from the water supply could plug the ﬁll

valve screen.

■ A square opening for proper operation and appearance

■ The cabinet front to be perpendicular to ﬂoor

■ A level ﬂoor

Helpful Hint: If ﬂoor at front of opening is not level with ﬂoor

at rear of opening, shims may be used to level dishwasher.

NOTE: To avoid shifting during dishwasher operation, shims

must be securely attached to the ﬂoor.

■ The location where the dishwasher will be installed must

provide clearance between motor and ﬂooring. Motor should

not touch the ﬂoor.

■ Do not install dishwasher over carpeted ﬂooring.

7

PRODUCT AND CABINET OPENING DIMENSIONS

25

1

/4"

(641 mm)

3

/4"

(19 mm)

A

30"

(762 mm)

3

/4"

(94 mm)

21"

(533 mm)

B

24"

(620 mm)

D

24"

(620 mm)

34"

(864 mm)

C

3

"

(76 mm)

1

3

/4"

(44 mm)

6

3

/4"

(172 mm)

2

1

/4"

(64 mm)

2

1

/4"

(64 mm)

2

"

(51 mm)

6

1

/4"

(159 mm)

10

1

/2"

(267 mm)

4

"

(102 mm)

A. Insulation may be compressed (not used on all models).

B. Door handles may protrude forward of the face of the

dishwasher, (varies by model).

For 4" (100 mm) toe kick, height of cabinet opening is 34

1

/

2

" (863 mm).

Check that all surfaces have no protrusions

that would prohibit dishwasher installation.

C. Measured from the lowest point on the underside

of the countertop. May be reduced to 33

1

/

2

"

(851 mm) by removing the wheels and perforated

area of insulation (blanket) on dishwasher.

D. Minimum, measured from narrowest point

of opening

NOTE: Shaded areas

of cabinet walls

show where utility

connections may

be installed.

8

ELECTRICAL REQUIREMENTS

Be sure that the electrical connection and wire size are

adequate and in conformance with the National Electrical

Code, ANSI/NFPA 70 – latest edition, and all local codes

and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

You Must Have:

■ 120-volt, 60 Hz, AC-only, 15- or 20-amp, fused

electrical supply

■ Copper wire only

■ A maximum of 2 ﬁeld wiring supply conductors

(12 AWG largest size) plus 1 grounding conductor

are permitted in the terminal box.

We Recommend:

■ A time-delay fuse or circuit breaker

■ A separate circuit

If Connecting Dishwasher with a Power Cord:

■ Use a UL Listed power cord kit marked for

use with dishwasher. See the “Tools and

Parts” section at the front of the guide for

part details and orders.

■ Plug into a grounded 3 prong outlet. Outlet must

meet all local codes and ordinances.

If Connecting Dishwasher with Direct Wiring:

■ Use ﬂexible, armored, or nonmetallic

sheathed copper wire with grounding

wire that meets the wiring requirements

for your home and local codes and ordinances.

■ Use a UL Listed/CSA Approved metallic strain relief.

See the “Tools and Parts” section at the front of the

guide for part details and orders.

DRAIN REQUIREMENTS

■ A new drain hose is supplied with your dishwasher. If drain

hose is not long enough, use a new drain hose with a

maximum length of 12 ft (3.7 m) that meets all current AHAM/

IAPMO test standards, is resistant to heat and detergent, and

ﬁts the 1" (25 mm) drain connector of the dishwasher. See

the “Tools and Parts” section at the front of the guide for part

details and orders.

■ Make sure to connect drain hose to waste tee or disposer

inlet above drain trap in house plumbing and 20" (508 mm)

minimum above the ﬂoor. It is recommended that the drain

hose either be looped up and securely fastened to the

underside of the counter or be connected to an air gap.

■ Make sure to use an air gap if the drain hose is connected

to house plumbing lower than 20" (508 mm) above

subﬂoor or ﬂoor.

■ If required, the air gap should be installed in accordance

with the air gap installation instructions. When you are

connecting the air gap, a rubber hose (not provided) will

be needed to connect to the waste tee or disposer inlet.

■ Use

1

/

2

" minimum I.D. drain line ﬁttings.

WATER SUPPLY REQUIREMENTS

■ This dishwasher has a water heating feature and also

requires a connection to a hot water supply line.

■ A hot water line with 20 to 120 psi (138 to 862 kPa)

water pressure can be veriﬁed by a licensed plumber.

■ 120°F (49°C) water at dishwasher

■

3

/

8

" O.D. copper tubing with compression ﬁtting or ﬂexible

braided water supply line. See the “Tools and Parts” section

at the front of the guide for part details and orders.

NOTE:

1

/

2

" minimum plastic tubing is not recommended.

■ A 90° elbow with

3

/

4

" hose connection with rubber washer.

See the “Tools and Parts” section at the front of the guide

for part details and orders.

■ Do not solder within 6" (152 mm) of the water inlet valve.

■ If installed in new construction, make sure the house

water supply lines have been ﬂushed prior to connecting

the dishwasher to remove any debris that may exist in

the supply line.

NOTE: If replacing an existing dishwasher, it is recommended

to install a new water line (see the “Tools and Parts” section at

the front of the guide for part details) and drain hose (supplied)

with the new dishwasher.

Use of air gap

Air gap

9

PREPARE CABINET OPENING –

NEW UTILITIES

NOTE: Refer to the “Product and Cabinet Opening Dimensions”

section for the correct hole placement and dimensions of the

shaded area.

Drill a 1

1

/

2

" (38 mm) drain hose hole in the side or rear of

cabinet, depending on location of drain hose routing and

drain hose connection location.

Drill a

1

/

2

" (12.7 mm) water supply hose hole in the side

or rear of cabinet, depending on location of water supply

routing and connection location.

Drill a 1

1

/

2

" (38 mm) electrical conduit hole in the right-hand

side or rear of cabinet.

WARNING

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

Electrical Shock Hazard

1. Disconnect power

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

2. Shut off water supply

Shut off the water supply to the dishwasher.

3. Drill hole locations –

new construction

Preferred

location

Optional

location

1

/

2

"

(38 mm)

1

/

2

"

(12.7 mm)

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover edges of hole with grommet included

with power cord kit. See the “Tools and Parts” section at

the front of the guide for part details.

Helpful Tip: Wiring the dishwasher will be easier if you route

the cable into the cabinet opening from the right-hand side.

INSTALL OPTIONAL MOISTURE BARRIER

RECOMMENDED FOR WOOD COUNTERTOPS

See the “Tools and Parts” section at the front of the guide for

part details and orders. Make sure the area under the cabinet

is clean and dry for installation of the moisture barrier. Remove

the backing of the moisture barrier and apply to underside of

the countertop along the front edge of the counter.

NOTE: Install wood shims if side anchoring and the gap

between the sides of the cabinet and sides of the dishwasher

are greater than

1

/

2

" (12.7 mm) on each side or are greater than

the length of the side anchor screws.

4. Sand holes smooth

Metal

cabinet

Wood

cabinet

Moisture barrier/Wood shims

Moisture

barrier

Install

wood

shims

INSTALLATION INSTRUCTIONS

10

Built-up ﬂoors: If the kitchen ﬂoor is higher than the cabinet

opening’s ﬂoor – for example, the kitchen ﬂoor tile does not

extend into the cabinet opening – add shims, as needed, in the

area shown to bring the dishwasher up to 34" (864 mm) below

the countertop.

NOTE: Shims must be securely attached to ﬂoor to avoid

movement when the dishwasher is in use.

Cut insulation blanket along perforation for cabinet opening

height of 33

1

/

2

" (851 mm). For other cabinet opening heights,

do not cut the insulation blanket.

5. Built-up ﬂoors – add shims

as needed

6. If installing into a

33

1

/

2

" (851 mm) opening

ELECTRICAL CONNECTION

– For Direct Wire, begin with Step 7

– For Power Cord, wait until Step 22

If installing with direct wire, route the cable as shown.

Route cable from power supply through cabinet hole. (Cable

must extend to the right front side of cabinet opening.) Tape

cable to the ﬂoor in area shown. This will prohibit cable from

moving when dishwasher is moved into cabinet opening.

NOTES:

■ If removing a previous dishwasher with a power cord, you will

need to transfer the power cord to the new dishwasher.

■ Direct wire connection to the dishwasher will not be done until

you get to Step 49.

7. Direct wire – route cable

11

PREPARE DISHWASHER

Helpful Tip: Place cardboard under dishwasher until installed

in cabinet opening to avoid damaging ﬂoor covering.

Using 2 or more people, grasp sides of dishwasher door

frame and place the dishwasher on its back.

Do not use the door panel as a worktable without ﬁrst

covering it with a towel to avoid scratching the door panel.

NOTE: On some models, once the dishwasher is on its back,

pull on the door handle to remove it from the access panel.

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

8. Put dishwasher on its back

REMOVE ACCESS PANEL

– For Plastic Access Panels, go to Step 9

– For Metal Access Panels, go to Step 10

Using a ﬂat-blade screwdriver, turn the plastic fasteners

1

/

4

turn counterclockwise to unlock them. Remove panel.

Do not remove tech sheet from access panel. Go to Step 11.

Using a

1

/

4

" nut driver or Phillips screwdriver, remove 2 screws

attaching access panel to dishwasher. Do not remove tech sheet

from access panel.

9. Plastic panel

1

/

4

turn

10. Metal panel

12

Measure height of cabinet opening from underside of

countertop to ﬂoor where dishwasher will be installed.

Be sure to measure the lowest point on the underside

of the countertop and the highest point on the ﬂoor.

Adjust both front and back leveling legs to the same height.

11. Measure cabinet opening

Dishwasher Height Adjustment Chart

Cabinet opening

height

Front legs

height A

Rear legs

height B

33

1

/

2

" (851 mm)

3

/

8

" (9.8 mm) Remove legs

and spacers.

34" (864 mm)

7

/

8

" (22 mm) 1" (25.4 mm)

34

1

/

2

" (876 mm) 1

1

/

8

" (28.8 mm) 1

1

/

4

" (31.3 mm)

Front legs – A

Rear legs – B

B

NOTE: If the minimum cabinet opening height is less than 33

7

/

8

"

(860 mm), the rear leveling legs and spacers can be removed for

additional clearance. This will allow the dishwasher to ﬁt into a

33

1

/

2

" (851 mm) high cabinet opening, but the dishwasher will

be more difﬁcult to move. (Measurements are approximate.

Rear and front leveling legs are preset at the factory for 34

1

/

2

"

[876 mm].)

Refer to the “Dishwasher Height Adjustment Chart” for height

of leveling legs needed for your cabinet opening.

Remove and discard the plastic rail cover on each side of

the dishwasher frame. To remove the plastic rail cover, push

upward and back to unsnap it from the dishwasher frame.

12. Adjust leveing legs

13. Remove plastic rail cover

(only on certain models)

Plastic rail cover

13

CONNECT WATER LINE TO FILL VALVE

– For Copper Line, begin with Step 14

– For Flexible Line, begin with Step 16

If using copper tubing, measure overall length of copper

tubing required to reach the water supply, cut to length, and

attach with compression ﬁttings.

Copper tubing only: Put the tubing into the 90° elbow ﬁtting

as far as it will go. (The copper tubing bends and kinks easily.)

Slide the nut and ferrule forward and start the nut onto the

elbow threads.

NOTE: To avoid vibration during operation, route the water

supply line so that it does not touch the dishwasher base,

frame, or motor. Go to Step 17.

14. Copper water line

15. Slide nut and ferrule onto tubing

(copper tubing only)

Nut

Ferrule

Flexible braided line: Conﬁrm the ﬂexible braided line is long

enough. See the “Tools and Parts” section at the front of the

guide for part details and orders.

Get

3

/

8

" compression x

3

/

4

" hose ﬁtting with 90° elbow. See

the “Tools and Parts” section at the front of the guide for part

details and orders. Connect the

3

/

8

" compression ﬁtting of the

90° elbow ﬁtting to the water supply line. Attach such that the

3

/

4

" connection is facing upward as shown above.

CONNECT FILL HOSE TO FILL VALVE

Be sure rubber washer is properly seated in ﬁtting. Slide the

3

/

4

" ﬁtting of the 90° elbow up to the valve and hand tighten to

avoid cross-threading. Hand tighten until the coupling is tight.

Using pliers, check the tightness of the coupling. An additional

1

/

4

to

1

/

2

turn may be required to seal the rubber gasket. Route

ﬁll hose out the rear left side of unit.

NOTES:

■ Do not use Teon

®†

tape with compression ﬁttings.

■ Do not over-tighten. Damage to the coupling can result.

†

®

TEFLON is a registered trademark of Chemours.

16. Flexible line

17. Add 90° elbow ﬁtting to the

water supply line

18. Tighten 90° elbow ﬁtting to valve

14

DRAIN HOSE CONNECTION

Place towel under drain hose to catch any water in drain hose.

Place the small (green) drain hose clamp onto the small end

of the drain hose. Push the new drain hose into the rubber

drain hose connector up to the drain hose stop.

Using pliers, squeeze open the small drain hose clamp,

and slide it onto the connector between stops.

NOTE: Route drain hose out the rear of the dishwasher.

19. Connect drain hose

Stop

Drain hose stop

Drain hose

Rubber drain hose

connector

Small clamp

20. Slide clamp onto connector

Stop

Drain hose stop

Drain hose

Rubber drain hose

connector

Small clamp

21. Hose clamp ﬁnal position

Stop

Drain hose stop

Drain hose

Rubber drain hose

connector

Small clamp

POWER CORD CONNECTION

NOTE: If removing a previous dishwasher with a power cord,

you will need to transfer the power cord to the new dishwasher.

Using a

1

/

4

" hex-head socket, nut driver, or Torx

®

T20

®

screwdriver, remove terminal box cover. Retain for later use.

Install a UL Listed/CSA Approved metallic strain relief.

Make sure screw heads are facing to the left when tightening

conduit nut. Strain relief is provided with the power cord

kit. See the “Tools and Parts” section at the front of the

guide for part details and orders.

Route cord so that it does not touch dishwasher motor or

lower part of dishwasher tub. Pull cord through strain relief

in terminal box.

NOTE: A maximum of 2 power cord supply conductors (12 AWG

largest size) plus 1 grounding conductor are permitted in the

terminal box.

22. Remove terminal box cover

23. Install strain relief

24. Power cord – route cord

into terminal box

15

Tighten strain relief screws to secure cord.

Place wires inside terminal box. Insert tabs on left side of cover.

Make sure wires are tucked inside the box and not pinched by

the cover. Use a

1

/

4

" hex-head socket, nut driver, or Torx

®

T20

®

screwdriver, and the screw removed in Step 22 to secure the

terminal box cover.

If power cord supplied model, remove the ﬁrst tie strap closest

to the plug to maximize the cord length. Do not remove any

other tie straps.

NOTE: Route power cord out the rear of the dishwasher.

Do not plug cord into an outlet until instructed to do so.

Wiring conﬁguration

27. Power cord – secure cord

in strain relief

28. Power cord – reinstall terminal

box cover and wires

Remove the ground connector screw and place it through the

ring terminal of the green ground wire of power cord. Reattach

and tighten the ground connector screw.

Select UL Listed/CSA Approved twist-on wire connectors of

the proper size. See the “Tools and Parts” section at the front

of the guide for part details. Connect wires, black to black and

white to white, using the twist-on wire connectors.

NOTE: Do not pre-twist stranded wire. Twist on wire connector.

Gently tug on wires to be sure both are secured.

WARNING

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

25. Power cord – connect ground wire

Ground

wire

26. Power cord – connect

remaining wires

16

IMPORTANT: If wheels were removed, cover the ﬂoor when

moving the dishwasher. Slowly move dishwasher completely

into cabinet opening. Do not kink or pinch water line, drain

hose, power cord, or direct wire between dishwasher and

cabinet. Remove cardboard from under dishwasher.

It is all right if dishwasher ﬁts tightly into cabinet opening.

Do not remove insulation blanket – the blanket reduces the

sound level.

NOTE: Route water supply, drain hose, and power cord out the

rear of the dishwasher.

Route the utilities through the holes in the cabinet and pull

the slack out at the same time as the dishwasher is pushed

into the cabinet.

If using a power cord, make sure to route end through hole

in cutout before sliding dishwasher into cabinet opening.

NOTE: Make sure insulation blanket is secured at both left and

right rear corners before pushing into cabinet opening to keep

the blanket from bunching up in a tight-ﬁtting cabinet.

31. Move dishwasher close

to cabinet opening

Water

line

Drain

hose

Cable

32. Route power cord

33. Secure insulation blanket

Insulation

blanket

Secure

blanket

INSTALL DOOR HANDLE

(ON SOME MODELS)

IMPORTANT: Do not scratch the front panel during this

procedure. If door panel has a protective ﬁlm, peel ﬁlm back

past the point of the handle studs before installing handle.

Handle is easiest to install while unit is on its back.

Remove the door handle and hex key from the packaging.

Setscrews are already installed in the handle. Place handle

on mounting studs with the setscrews facing down. Push

the door handle tightly against the door. Insert the short end

of the hex key into the setscrews. Tighten the setscrews

1

/

4

turn past snug.

Retain hex key with Installation Instructions.

PLACE DISHWASHER IN CABINET

Using 2 or more people, stand the dishwasher up.

NOTE: Do not install kick plate until instructed to do so.

29. Install door handle

Handle

Mounting stud

Setscrew

(in bottom

of handle)

Hex key

WARNING

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

30. Stand dishwasher upright

17

Countertop Attachment:

Remove the brackets from the package and insert into the

open slots on the left- and right-hand top of the dishwasher

collar as shown. Go to Step 41.

Using pliers, bend/twist tab to lock the brackets in place.

Side Attachment:

Break off the end of the bracket along the scored line

using pliers.

36. Insert bracket

Tabs must point

to the right.

Bend tab

37. Break end of bracket

Score line for

plastic tub models

Score line for

plastic tub models

Score line for

plastic tub models

Scored line for

stainless steel

tub models

Scored line

for plastic tub

models

NOTE: Leave unit about 6" (152 mm) out from cabinet in order

to install anchor brackets and adjust door tension if needed.

NOTE: Pull slack out of utilities at the same time the

dishwasher is pushed into the cabinet opening to avoid

any kinks.

CHOOSE ANCHOR ATTACHMENT METHOD

IMPORTANT: The dishwasher must be secured to the

cabinet as one of the ﬁnal steps. Prepare the dishwasher for

this by attaching the 2 brackets found in the parts bag to

the dishwasher.

– For countertops that are wood, laminate, or another

similar surface, use Countertop Attachment: go to

Step 36

– For countertops that are marble, granite, or another

hard surface, use Side Attachment: go to Step 37

NOTE: If the gap between the top of the door and the

underside of the counter top is tight (less than

1

/

4

" [6,35 mm]),

we suggest using Side Attachment to keep from scratching

the User Interface or console with the anchor screws.

34. Move dishwasher all but 6" (152 mm)

into cabinet opening

6"

(152 mm)

35. Pull slack from utilities

18

If the door falls open, increase the spring tension by moving

the spring end toward the back of the dishwasher.

NOTE: Springs should be in the same notches on left and

right sides.

Align front of dishwasher door panel with front of cabinet

doors. You may need to adjust alignment to be even with

your cabinets.

Check that leveling legs are ﬁrmly against the ﬂoor. Close and

latch the door and place level against the front panel. Check

that dishwasher is centered from front to back in the opening.

If needed, adjust leveling leg until dishwasher is plumb. Repeat

for other side of dishwasher.

Helpful Tip: Push up on front of dishwasher to raise dishwasher

off the ground to adjust front legs. With some installations, it

may be easier to adjust the front leg using a

3

/

16

" hex head

socket or adjustable wrench. If the gap between the top of the

door and the underside of the counter top is tight (less than

1

/

4

" [6 mm]), we suggest side anchoring to keep from scratching

the User Interface or console.

41. Door falls open –

increase spring tension

42. Align front of dishwasher

with front of cabinet doors

43. Check for plumb and

adjust legs if needed

Push bracket into slot on the side of dishwasher and bend

tab in toward the side of the dishwasher so that it keeps

the bracket in place. Repeat this step for the other side of

the dishwasher.

NOTE: Install wood shims to the inside of the cabinets if the

gap between the sides of the cabinet and the sides of the

dishwasher are greater than

1

/

2

" (13 mm) on each side.

NOTE: Do not attach the dishwasher. This will be done later.

FINAL INSTALLATION CHECK

If the door closes too quickly, decrease the spring tension by

moving the spring end toward the front of the dishwasher.

NOTE: Springs should be in the same notches on left and

right sides.

38. Install bracket

Bend

tabs

39. Open and close door

40. Closes too quickly –

decrease spring tension

19

SECURE DISHWASHER

IN CABINET OPENING

Check that dishwasher is still level front to back and side

to side in the cabinet opening.

Open dishwasher door and place towel over pump assembly

and spray arm of dishwasher. This will keep screws from

falling into pump area when you are securing dishwasher

to countertop or cabinet.

Open dishwasher door to prepare for securing the dishwasher

to the countertop or side cabinet.

NOTES:

■ The dishwasher must be secured to keep it from shifting

when the door is opened or closed.

■ Do not drop screws into bottom of dishwasher.

■ Locate brackets installed in the “Choose Anchor Attachment

Method” section, either on top or on the sides of the

dishwasher.

■ If countertop anchoring: Secure dishwasher to the

countertop with two #10 x

1

/

2

" Phillips-head screws (included).

■ If side anchoring: Drill pilot holes in cabinet to avoid

splitting the wood. Secure dishwasher to cabinet with two

#10 x

1

/

2

" Phillips-head screws (included). Remove upper

rack for easier access. See the Use and Care Guide for

instructions how to remove the upper rack if needed.

45. Double-check dishwasher

alignment in cabinet opening

46. Secure dishwasher

Screw to side

cabinet

Place level against top front opening of tub. Check that

dishwasher is level from side to side. If dishwasher is not

level, adjust front legs up or down until dishwasher is level.

Level legs

Optional methodPreferred method

44. Check level side to side

and adjust legs if needed

20

DIRECT WIRE CONNECTION

Using a

1

/

4

" hex-head socket, nut driver, or Torx

®

T20

®

screwdriver, remove terminal box cover. Retain for later use.

Install a UL Listed/CSA Approved metallic strain relief.

See the “Tools and Parts” section at the front of the guide

for part details and orders.

Route cable so that it does not touch dishwasher motor or

lower part of dishwasher tub. Pull cable through UL Listed/

CSA Approved strain relief in terminal box. Strain relief is not

supplied with the dishwasher. Owner must purchase a

7

/

8

"

screw-in type strain relief.

Select UL Listed/CSA Approved twist-on wire connectors (not

included) rated to connect your household wiring to 16-gauge

dishwasher wiring.

49. Remove terminal box cover

50. Install strain relief

51. Route cable into terminal box

IMPORTANT: Check that top of door does not contact screws,

brackets, or countertop. If it does, adjust leveling legs or use

the side attachment option.

Open door and check that space between dishwasher cabinet

opening, and tub is equal on both sides. If spacing is not equal,

loosen bracket screws and shift tub. Tighten bracket screws.

47. Check door clearance

48. Check inner spacing

La page charge ...

Whirlpool WDF130PAHS Guide d'installation

Ce manuel convient également à

Whirlpool WDF130PAHS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents