Extron HAI 100 4K Plus Manuel utilisateur

Taper
Manuel utilisateur
HAI 100 4K Plus
Setup Guide
The Extron HAI 100 4K Plus is an audio embedder that embeds either two-channel analog audio, or two-channel or multi-channel
S/PDIF digital audio onto the HDMI output signal. The HAI 100 4K Plus includes an HDMI input, analog stereo audio and S/PDIF
audio inputs, as well as an HDMI output.
Mounting
The HAI 100 4K Plus can be placed on a desktop or tabletop using the included rubber feet, or mounted to a rack or furniture (see
the HAI 100 4K Plus User Guide, available at www.extron.com, for mounting options and instructions).
Cabling
Rear Panel Features and Cabling
CONFIG
HAI 100 4K PLUSE
SIGNAL
HDCP
IN OUT
POWER
12V
0.4A MAX
OUTPUT AUDIO INPUTSINPUT
HAI 100 4K PLUS
LR
S/PDIFANALOG
AA
BB
CC
BB
EE
CC
AA
DD
Figure 1. HAI 100 4K Plus Rear Panel
A
Power input — Connect the provided power supply to the 3.5 mm, 2-pole captive
screw power receptacle (see the image at right).
ATTENTION:
Do not connect the power supply before reading the Attention in the
Power Supply section of the HAI 100 4K Plus User Guide.
Ne branchez pas la source d’alimentation externes avant d’avoir lu les
mises en garde dans la section «PowerSupply» du HAI 100 4K Plus
User Guide.
B
HDMI input — Connect an HDMI input source into this female HDMI type A connector.
NOTE: By default, the EDID stored at the HDMI input is set to 1080p at 60 Hz with 2-channel audio. EDID can be
congured using Extron PCS software (see Configuration on the next page).
C
HDMI output — Connect an HDMI output device into this female HDMI type A connector.
D
Analog audio input — Connect an analog audio device to this 5-pole 3.5 mm captive screw connector (see figure 2). This
connector accepts 2-channel stereo balanced or unbalanced audio.
NOTE: By default, the HAI 100 4K Plus is congured to always embed analog audio. This can be congured using
Extron PCS software or SIS commands (see Configuration on the next page).
Do not tin the wi
res!
Balanced Audio Input
Tip
Ring
Tip
Ring
Sleeves
Unbalanced Audio Input
Tip
No Ground Here
No Ground Here
Tip
Sleeves
LR
LR
Figure 2. Analog Input Connector Wiring
ATTENTION:
Connect the sleeve to the ground (Gnd) terminal. Connecting the sleeve to a negative (-) terminal will damage the
audio output circuits.
Connectez le manchon à la terminaison terre (Gnd). Connecter le manchon à une terminaison négative (-)
endommagera les circuits de la sortie audio.
SECTION A–A
AA
Power Supply
Output Cord
Captive Screw
Connector
Ridges
Smooth
3/16"
(5 mm) Max.
A
Power input
D
Analog audio input
B
HDMI input
E
S/PDIF audio input (see the next page)
C
HDMI output
68-3110-50
Rev. A
03 20
© 2020 Extron Electronics — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
E
S/PDIF audio input — Connect a S/PDIF audio output device into this female RCA connector. This connector accepts
digital S/PDIF audio formats (2-channel LPCM, Dolby Digital, or DTS).
NOTE: The HAI 100 4K Plus can be congured to embed S/PDIF audio using Extron PCS Software or SIS
commands (see “Conguration” below).
Front Panel Features and Cabling
CONFIG
HAI 100 4K PLUSE
SIGNAL
HDCP
IN OUT
POWER
12V
0.4A MAX
OUTPUT AUDIO INPUTSINPUT
HAI 100 4K PLUS
LR
S/PDIFANALOG
AA
BB
CC
BB
EE
CC
AA
DD
Figure 3. HAI 100 4K Plus Front Panel
A
Power LED — The LED indicator lights when the unit is receiving power.
B
Config port — Connect a control PC to this female Mini-B USB Cong port to update the rmware, congure various
functions of the unit, and view the current status of the unit.
C
Input and Output LEDs — These four LEDs provide the status of the HDMI input and output:
Signal — Input LED lights when the unit is receiving a signal on the HDMI input.
Output LED lights when a sink device is connected to the HDMI output.
HDCP — Input LED lights when the input signal is HDCP encrypted.
Output LED lights when an HDCP compliant sink device is detected and the output is encrypted.
Configuration
Several HAI 100 4K Plus features can be congured using Extron PCS software or SIS commands:
Extron Product Configuration Software (PCS): To congure the unit using PCS, download the software from
www.extron.com (see the HAI 100 4K Plus User Guide for details).
Simple Instruction Set™ (SIS) commands: SIS commands can be sent from a PC to the HAI 100 4K Plus using Extron
DataViewer or other command interface (see the “SIS Commands” section of the HAI 100 4K Plus User Guide).
  • Page 1 1
  • Page 2 2

Extron HAI 100 4K Plus Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues