Extron HAE 100 4K Manuel utilisateur

Extron
Marque
Extron
Modèle
HAE 100 4K
Catégorie
Commutateurs vidéo
Taper
Manuel utilisateur
User Guide
HAE 100 4K
HDMI
HDMI Audio Extractor
68-2802-01 Rev. B
01 19
Safety Instructions
Safety Instructions • English
WARNING: This symbol, , when used on the product, is intended to
alert the user of the presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und
die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf.
68-290-01, sur le site Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di tensione non isolata pericolosa
all’interno del contenitore del prodotto che può costituire un rischio di
scosse elettriche.
ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di importanti istruzioni di funzionamento
e manutenzione nella documentazione fornita con l’apparecchio.
Per informazioni su parametri di sicurezza, conformità alle normative,
compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento
alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo
68-290-01, sul sito web di Extron, www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu
poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie
porażenia prądem elektrycznym.
UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do
ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji
wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne,
zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część
numer 68-290-01, na stronie internetowej Extron, www.extron.com.
Инструкция по технике безопасности • Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии неизолированного опасного
напряжения внутри корпуса продукта, которое может привести к поражению
электрическим током.
ВНИМАНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии важных инструкций
по эксплуатации и обслуживанию в руководстве,
прилагаемом к данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других
вопросах см. руководство по безопасности и соблюдению
нормативных требований Extron на сайте Extron: ,
www.extron.com, номер по каталогу - 68-290-01.
安全说明 • 简体中文
警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 电压，
有触电危险。
注意： 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修）说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见
Extron 安全规范指南，产品编号 68-290-01
。
안전 지침 • 한국어
경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합
니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및
규제 준수 안내서, 68-290-01 조항을 참조하십시오.
安全記事 • 繁體中文
警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著
可能會導致觸電之風險的未絕緣危險電壓。
注意 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有
重要的操作和維護（維修）説明。
有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資
訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規
遵守手冊》，準則編號 68-290-01。
安全上のご注意
• 日本語
警告: この記号 が製品上に表示されている場合は、筐体内に絶縁されて
いない高電圧が流れ、感電の危険があることを示しています。
注意:この記号 が製品上に表示されている場合は、本機の取扱説明書
に 記載されている重要な操作と保守(整備)の指示についてユーザーの
注意を喚起するものです。
安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に
つ い て は 、エ ク スト ロ ン の ウ ェブ サ イト www.extron.com よ り 『 Extron Safety
and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。
Copyright
© 2016
-2019 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks(
®
), registered service marks(
SM
), and trademarks(
TM
) are the property of RGBSystems, Inc. or
ExtronElectronics (see the current list of trademarks on the Terms of Use page at www.extron.com):
Registered Trademarks
(
®
)
Extron, AVTrac, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Global Configurator,
GlobalScripter, GlobalViewer, Hideaway, Inline, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA,
PlenumVault, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, SystemINTEGRATOR, TeamWork,
TouchLink, V-Lock, VersaTools, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, and XTPSystems
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
™
)
AAP, AFL (Accu-RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS(ClassD Ripple
Suppression), DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator,
DSVP(Digital Sync Validation Processing), eLink, EQIP, FastBite, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital,
Opti-Torque, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, ShareLink, SIS, SimpleInstructionSet,
Skew-Free, SpeedNav, Triple-Action Switching, True4K, Vector™ 4K , WebShare, XTRA, ZipCaddy, and ZipClip
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference. This interference must be corrected at the expense of the user.
NOTE: This unit was tested with shielded I/O cables on the peripheral devices. Shielded cables
must be used to ensure compliance with FCC emissions limits.
For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility,
accessibility, and related topics, see the “Extron Safety and Regulatory Compliance
Guide” on the Extron website.
Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
ATTENTION: Attention indicates a situation that may damage or destroy the product or
associated equipment.
NOTE: A note draws attention to important information.
Software Commands
Commands are written in the fonts shown here:
^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C
[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]
E X! *X1&* X2)* X2#* X2! CE}
NOTE: For commands and examples of computer or device responses
mentioned in this guide, the character “0” is used for the number zero and “O”
is the capital letter “o.”
Computer responses and directory paths that do not have variables are written in the font
shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the File menu, select New.
Click the OK button.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
vHAE 100 4K • Contents
Contents
Introduction............................................................ 1
About the HAE 100 4K HDMI Audio Extractor .... 1
Features ............................................................. 2
Panels and Cabling .............................................. 3
Front Panel Features ........................................... 3
Rear Panel Features and Cabling ........................ 3
Configuration ......................................................... 6
EDID Minder ....................................................... 6
Available EDID ................................................ 6
Setting EDID with PCS Software ..................... 7
Audio Input Format ............................................. 7
TMDS Output Format ..................................... 8
Color bit depth support................................... 8
Hot Plug Detect (HPD) .................................... 8
Input ............................................................... 8
Output ............................................................ 9
SIS Commands ................................................... 10
Connecting a Control Computer ....................... 10
Simple Instruction Set (SIS) Control .................. 10
Host-to-Interface Communications ............... 10
Error Responses ........................................... 10
Timeout ........................................................ 10
Using the Command and Response Table .... 10
Symbol definitions ........................................ 11
Command and Response Table for SIS
Commands ..................................................... 13
Reference Information ...................................... 15
Mounting .......................................................... 15
Tabletop Placement ...................................... 15
Rack Mounting ............................................. 15
Under-desk and Furniture Mounting .............. 16
PCS Software ................................................... 16
Downloading PCS ........................................ 16
Using PCS .................................................... 17
Updating Firmware with Firmware Loader ......... 17
Downloading Extron Firmware Loader .......... 17
Installing Firmware Loader ............................ 17
Downloading Firmware ................................. 18
Installing Firmware with Firmware Loader ...... 19
Extron Warranty .................................................. 20
HAE 100 4K • Introduction 1
Introduction
This section covers the following topics:
• About the HAE 100 4K HDMI Audio Extractor
• Features
About the HAE 100 4K HDMI Audio Extractor
The HAE 100 4K is a one HDMI input, one HDMI output audio de-embedder that extracts
the audio from an HDMI signal, including audio from 4K sources. It accepts an HDMI input,
extracts the digital audio from the HDMI signal, and provides a digital S/PDIF audio output
and an analog stereo audio output. It provides outputs for stereo and dual mono analog
audio signals, as well as digital multi-channel or two-channel S/PDIF audio.
It is HDCP compliant, supports data rates up to 10.2 Gbps, and is compatible with video
resolutions up to 4K.
100-240V 0.5A
50-60Hz
INPUTS
DIGITAL
OUTPUTS
SSP 7.1
1
2
3
5
ANALOG
FRONT
SIDE
CENTER
SURROUND
BACK
RS-232
Tx Rx
SUB
WOOFER
4
L R
L R C LS RS LB/CB RB SUB
100-240V 1.5A, 50-60 Hz
STANDBY
XPA 2004
GREEN - ACTIVE
AMBER - STANDBY
1
G
2
21 43
3 4
LIMITER/
PROTECT
SIGNAL
1 2
(BRIDGE A)
0
2
4
6
8
10
12
18
14
26
∞
0
2
4
6
8
10
12
14
∞
0
2
4
6
8
10
12
14
∞
0
2
4
6
8
10
12
14
∞
ATTENUATION
INPUTS BRIDGE
MODE
8Ω / 4Ω OUTPUTS
REMOTE
3 4 A B
(BRIDGE B)
CLASS 2 WIRING
1 2 3 4
ON
OFF
BRIDGE
8Ω ONLY
BRIDGE A BRIDGE B
100-240V 1.5A, 50-60 Hz
STANDBY
XPA 2004
GREEN - ACTIVE
AMBER - STANDBY
1
G
2
21 43
3 4
LIMITER/
PROTECT
SIGNAL
1 2
(BRIDGE A)
0
2
4
6
8
10
12
18
14
26
∞
0
2
4
6
8
10
12
14
∞
0
2
4
6
8
10
12
14
∞
0
2
4
6
8
10
12
14
∞
ATTENUATION
INPUTS BRIDGE
MODE
8Ω / 4Ω OUTPUTS
REMOTE
3 4 A B
(BRIDGE B)
CLASS 2 WIRING
1 2 3 4
ON
OFF
BRIDGE
8Ω ONLY
BRIDGE A BRIDGE B
HAE 100 4K
12V
0.6A MAX
POWER
INPUT OUTPUT AUDIO OUTPUTS
S/PDIF
ANALOG
L R
Extron Extron Extron
Extron Extron
Extron Extron
STANDBY/ON
PQLS HDMI OPEN/CLOSE FL OFF
USB
Extron
HAE 100 4K
HDMI 4K Audio
De-Embedder
Extron
SSP 7.1
Surround Sound
Processor
Extron
XPA 2004
Four Channel Amplier -
200 Watts Per Channel
Extron
XPA 2004
Four Channel Amplier -
200 Watts Per Channel
90” Monitor
Powered
Subwoofer
HDMI
Audio
AudioAudioAudio
L C R
LS LBS RBS
Audio
Audio
Audio
HDMI
Extron
SM 26
Surface Mount
Speakers
Audio AudioAudioAudio
RS
Extron
SM 26
Surface Mount
Speakers
Figure 1. HAE 100 4K Application Diagram
NOTE: This product does not decode or downmix Dolby
®
Digital or DTS
®
audio formats.
HAE 100 4K • Introduction 2
Features
• HDMI audio de-embedding with analog stereo or dual mono, and digital S/PDIF
audio outputs — The HAE 100 4K supports analog stereo, dual mono, or two-channel
LPCM audio. For audio systems without HDMI, the S/PDIF output supports Dolby or
DTS
®
multi-channel surround sound.
• HDMI input
• De-embeds audio with or without HDMI output connected
• Embedded digital audio output — The HDMI output re-embeds the audio taken from
the HDMI input.
• S/PDIF output — Allows for digital audio output over a single RCA connector.
• Analog output — Allows for two channel stereo analog audio output over a 5-pole,
3.5 mm captive screw connector.
• HDMI audio pass-through — Provides audio signal pass-through for all embedded
audio formats on the HDMI output. The embedded audio output can also be muted.
• Supports computer and video resolutions up to 4K, including 1080p/60 Deep
Color
• Supported HDMI specification features include data rates up to 10.2 Gbps,
Deep Color up to 12-bit, 3D, and CEC pass-through
• EDID Minder automatically manages EDID communication between connected
devices — Ensures that the source powers up properly and reliably outputs content for
display.
• HDCP compliant — Prevents the reproduction of copyright protected content.
• User-selectable HDCP authorization — Allows the HAE 100 4K to appear HDCP
compliant or non-HDCP compliant to the connected source, which is beneficial if the
source automatically encrypts all content when connected to an HDCP-compliant
device. Protected material is not passed in non-HDCP mode.
• Selectable TMDS output format — Allows the output video format, color space, and
quantization to be manually configured.
• Automatic HDMI input cable equalization to 50 feet (15 meters) at 4K, or 100
feet (30 meters) at 1080p/60 when used with Extron HDMI Pro cables — Actively
conditions incoming HDMI signals to compensate for signal loss when using long
cables, low quality cables, or source devices with poor HDMI signal output.
• Input and Output LEDs — Provide the status of various functions, including signal
presence, HDCP authentication, and the de-embedded audio format.
• Front panel USB configuration port — One female mini USB type B is used to
update the firmware of the product and check the status of the various functions of the
product.
• Rack-mountable 1” (2.5 cm) high, quarter rack width metal enclosure
• External universal ENERGY STAR
®
qualified power supply included,
replacement part number 70-775-01 — Provides worldwide compatibility, low power
consumption, and reduced operating costs.
HAE 100 4K • Panels and Cabling 3
Panels and
Cabling
This section covers the following:
• Front Panel Features
• Rear Panel Features and Cabling
Front Panel Features
SIGNAL
IN OUT
CONFIG
HDCP
AUDIO IN
2-CH LPCM
BITSTREAM
HAE 100 4K
HAE 100 4K
12V
0.6A MAX
POWER
INPUT OUTPUT AUDIO OUTPUTS
S/PDIF
ANALOG
LR
BB
EE
CC
AA
DD
AA
BB
DD
CC
Figure 2. HAE 100 4K Front Panel
A
Power LED — The LED indicator lights when the unit is receiving power.
B
Config port — Use this female type B mini USB to update the firmware, configure
various functions of the unit, and view the current status of the unit.
C
Input and Output LEDs — These four LEDs provide the status of the HDMI input:
• Signal — This LED lights when the unit is receiving a signal on the HDMI input.
• HDCP — This LED lights when the input signal is HDCP encrypted.
D
Audio input LEDs — These two LEDs provide the status of the various HDMI and
audio input functions:
• 2-CH PCM — This LED lights when the incoming embedded audio signal is a
2-channel Digital LPCM audio format.
• Bitstream — This LED lights when the incoming embedded audio signal is a Dolby
Digital or DTS audio format.
Rear Panel Features and Cabling
SIGNAL
IN OUT
CONFIG
HDCP
AUDIO IN
2-CH LPCM
BITSTREAM
HAE 100 4K
HAE 100 4K
12V
0.6A MAX
POWER
INPUT OUTPUT AUDIO OUTPUTS
S/PDIF
ANALOG
LR
BB
EE
CC
AA
DD
AA
BB
DD
CC
Figure 3. HAE 100 4K Rear Panel
A
Power input (see the next page)
B
HDMI input (see the next page)
C
HDMI output (see page 5)
D
S/PDIF output (see page 5)
E
Analog output (see page 5)
HAE 100 4K • Panels and Cabling 4
A
Power input — Connect the provided power supply to the 3.5 mm, 2-pole captive
screw power receptacle (see figure 4).
SECTION A–A
Ridges
Smooth
Power Supply Output Cord
A
A
3/16”
(5 mm) Max.
Figure 4. Power Connection
ATTENTION:
• The length of the exposed wires in the stripping process is critical. The ideal length
is 3/16 inches (5 mm). Any longer and the exposed wires may touch, causing a
short circuit between them. Any shorter and the wires can be easily pulled out even
if tightly fastened by the captive screws.
• La longueur des câbles exposés est primordiale lorsque l’on entreprend de les
dénuder. La longueur idéale est de 5mm (3/16inches). S’ils sont un peu plus
longs, les câbles exposés pourraient se toucher et provoquer un court circuit. S’ils
sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis
captives.
• Always use a power supply supplied by or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification and may
cause damage to the supply and the end product.
• Utilisez toujours une source d’alimentation fournie par Extron. L’utilisation d’une
source d’alimentation non autorisée annule toute conformité réglementaire et peut
endommager la source d’alimentation ainsi que l’unité.
• If not provided with a power supply, this product is intended to be supplied by a
power source marked “Class 2” or “LPS” and rated at 12 VDC and a minimum of
1.0 A.
• Si ce produit ne dispose pas de sa propre source d’alimentation électrique, il doit
être alimenté par une source d’alimentation de classe 2 ou LPS et paramétré à 12
V et 1.0 A minimum.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities. The power supply is to be located within the same vicinity
as the Extron AV processing equipment in an ordinary location, Pollution Degree 2,
secured to the equipment rack within the dedicated closet, podium, or desk.
• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une
utilisation dans les espaces d’aération ou dans les cavités murales. La source
d’alimentation doit être située à proximité de l’équipement de traitement audiovisuel
dans un endroit ordinaire, avec un degré2 de pollution, fixé à un équipement de
rack à l’intérieur d’un placard, d’une estrade, ou d’un bureau.
• The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical
Code part 1, section 16. The power supply shall not be permanently fixed to
building structure or similar structure.
• Cette installation doit toujours être en accord avec les mesures qui s’applique
au National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical
Code, partie1, section16. La source d’alimentation ne devra pas être fixée de
façon permanente à une structure de bâtiment ou à une structure similaire.
B
HDMI input — Connect an HDMI input source into this female HDMI type A connector.
HAE 100 4K • Panels and Cabling 5
C
HDMI output — Connect an HDMI output device into this female HDMI type A
connector.
NOTES:
• It is not required to connect an HDMI output device to extract audio from the
HDMI input device.
• The HDMI output passes all audio formats, regardless of configuration. The
embedded audio output can also be muted through SIS command.
• If the HDMI input signal is HDCP encrypted, the HDMI output signal will also
be encrypted. If the HDMI input signal is not HDCP encrypted, the output
signal will not be encrypted.
• If the HDMI input signal is HDCP encrypted and the HDMI output device is not
HDCP compliant, the unit outputs a green screen.
D
S/PDIF audio output — Connect an S/PDIF audio output device into this female RCA
connector. This connector outputs digital S/PDIF audio formats (2-channel LPCM,
Dolby Digital, or DTS).
NOTE: The audio format present on this output is determined by the content on the
source device.
E
Analog audio output — Connect an audio output device to this 5-pole 3.5 mm
captive screw connector (see figure 5). This connector outputs a 2-channel stereo
analog audio format.
NOTE: By default, this output is configured for stereo audio. It can be configured for
dual mono audio using PCS (see PCS Software on page 16) or SIS commands
(see SIS Commands on page 10).
Do not tin the wires!
Balanced Audio Output
Tip
Ring
Tip
Ring
Sleeves
Unbalanced Audio Output
Tip
No Ground Here
No Ground Here
Tip
Sleeves
LR
LR
Figure 5. Analog Output Connector Wiring
ATTENTION:
• Connect the sleeve to the ground (Gnd) terminal. Connecting the sleeve to a
negative (-) terminal will damage the audio output circuits.
• Connectez le manchon à la terminaison terre (Gnd). Connecter le manchon
à une terminaison négative (-) endommagera les circuits de la sortie audio.
HAE 100 4K • EDID Configuration 6
Configuration
To ensure that the sink devices can handle the signal provided, the following HAE 100 4K
features can be configured using SIS commands (see the next section, SIS Commands, on
page 10 for instructions). This section provides information on:
• EDID Minder
• Audio Input Format
• Output Compatibility Correction
• HDCP
EDID Minder
EDID Minder allows a source device connected to the HAE 100 4K input to continuously see
the EDID of a sink device, even if the sink is not physically connected. An EDID file can also be
assigned to the HDMI input, emulating a sink device with the desired characteristics.
By default, the EDID is set to 720p @ 60 Hz with 2-channel audio.
Available EDID
The table at the bottom of this page lists all available EDID options, which include:
• 12 factory-loaded EDID - Factory EDID is categorized by rate type (IT or CE). Each entry
in the table has two audio versions: one for 2-Ch LPCM audio, and one for S/PDIF audio.
The audio input format setting determines which version is active.
• 1 output slot that is automatically populated by EDID from the connected sink device. The
EDID of the sink device is stored automatically upon hot plug detection (HDP).
NOTE: When the sink is removed or power to the HAE 100 4K is cycled, the EDID is
removed from the slot. The EDID is replaced with the default value until a new sink is
detected and a new EDID is stored.
• 2 user slots that can be manually populated with EDID imported by the user. These two
slots are available for storing imported EDID files. These slots contain the default EDID until
they are overwritten by the imported files. The imported files remain in the slots until they are
overwritten or the unit is reset.
NOTE: In the table below,
X^
is the SIS symbol representing the EDID file number
(1 through 15). To change the EDID, enter the following SIS command (see SIS
Commands on page 10 for details on entering SIS commands):
E
A *
X^
EDID
}
(where
X^
= 9 [default EDID] or the desired EDID file number)
X^
Native
Resolution
Refresh
Rate
Rate
Type
Video
Format
Audio Notes
1 1280 x 800 60 Hz IT HDMI
2-Ch or S/PDIF
2 1440 x 900 60 Hz IT HDMI
3 1600 x 900 60 Hz IT HDMI
4 1680 x 1050 60 Hz IT HDMI
5 1920 x 1200 60 Hz IT HDMI
HAE 100 4K • EDID Configuration 7
X^
Native
Resolution
Refresh
Rate
Rate
Type
Video
Format
Audio Notes
6 2560 x 1440 60 Hz IT HDMI
2-Ch or S/PDIF
7 2560 x 1600 60 Hz IT HDMI
8 720p 50 Hz CE HDMI
9 720p 60 Hz CE HDMI Default EDID
10 1080p 50 Hz CE HDMI
11 1080p 60 Hz CE HDMI
12 4K/UHD 60 Hz CE HDMI
13 Output (Automatic) - Populated by EDID from sink device.
Automatically populated with
EDID from connected sink
devices.
14 User Slot 1 - Manually populated by user/PCS. Manually populated by the
user using PCS software (see
page 16) or SIS commands
(see page page 10)
15 User Slot 2 - Manually populated by user/PCS.
Setting EDID with PCS Software
EDID settings and other HAE 100 4K features can be configured using PCS software (see
PCS Software on page 16).
Audio Input Format
The audio input format determines which audio formats are specified in the assigned EDID,
as well as whether or not the analog audio output is active.
There are two audio input format options, which can be configured through SIS commands:
• 2-Channel LPCM (default)
• S/PDIF, which also disables the analog audio output
See the table below for details:
Audio Input
Format
Supported Audio Formats Active Audio
Output(s)
2-Ch LPCM LPCM 2-Channel, 16/20/24 bit depths, 32/44.1/48 kHz sampling
Analog Audio
& S/PDIF
S/PDIF
• LPCM 2-Channel, 16/20/24 bit depths, 32/44.1/48 kHz
sampling
• Dolby Digital (AC-3) 6-Channel, 640k mbr, 32/44.1/48 kHz
sampling
• DTS 7-Channel, 1536k max bit rate, 44.1/48 kHz sampling
S/PDIF only
Output Compatibility Correction
EDID Minder manages the EDID stored at the HDMI input and presented to the source device.
However, additional functionality may be required to ensure that all output devices remain
compatible with the signal from the source.
The HAE 100 4K scans and monitors the EDID of the sink device connected to the HDMI output.
It determines the interface (DVI or HDMI) and color depth, and uses that information to adjust the
signal so that it is compatible with the output device.
HAE 100 4K • EDID Configuration 8
TMDS Output Format
The TMDS output format has three components:
• Video format — either DVI or HDMI
• Color space — RGB 4:4:4, YUV 4:2:2, or YUV 4:4:4
• Quantization range — either full (0-255) or limited (16-235)
To set the TMDS output format, use the SIS commands shown on page 13.
By default, the output format is configured for Auto, which automatically forces RGB 4:4:4
Full. The video format depends on the source signal and the sink capabilities.
NOTE: When the source signal is detected as 4K/UHD @ 60 Hz with YUV 4:2:0 (based on
AVI infoframe data), it passes unaltered, overriding the TMDS output format setting. If the
TMDS output format is changed while the signal is passing, the setting is applied, but
with no observable change. The TMDS output format will resume as configured when the
source signal changes to a signal other than 4K/UHD @ 60 Hz with YUV 4:2:0.
Other TMDS output formats, which can be set using the Output TMDS Format SIS
command on page 13, include:
• DVI RGB 4:4:4
• HDMI RGB 4:4:4 Full
• HDMI RGB 4:4:4 Limited
• HDMI YUV 4:4:4 Limited
• HDMI YUV 4:2:2 Limited
Color bit depth support
If the incoming signal uses deep color but the sink device does not support it, the color
depth is truncated to the next best color depth, as reported in the sink EDID. The options
are:
• 12-bit > 10-bit
• 12-bit > 8-bit
• 10-bit > 8-bit
This feature can be set to always force 8-bit, using the Output Color Bit Depth SIS
command on page 13.
Hot Plug Detect (HPD)
The HAE 100 4K monitors HPD on each HDMI output to determine if a new sink has been
connected. If necessary, the signal for that output is modified in response to the EDID of the
connected device.
HDCP
Input
The HAE 100 4K input authenticates HDCP with the source device if the source requires HDCP
encryption. The authentication process is repeated whenever the stored EDID is changed or
updated.
HDCP support can be disabled using the Input HDCP Authorization SIS Command on
page 13.
HAE 100 4K • EDID Configuration 9
Output
The output is authenticated and encrypted according to the configured HDCP output mode (see
output modes below). If the output requires encryption but the connected sink device cannot be
authenticated, the HAE 100 4K outputs a green screen.
HDCP output modes
• Follow input — Output is always authenticated but only encrypted when required by
input. HDMI authentication is continuous. DVI authentication occurs for a maximum of
10 seconds, then fails. This is the default mode.
• Always encrypt output — Output is always authenticated and encrypted. HDMI
authentication is continuous. DVI authentication occurs for a maximum of 10 seconds,
then fails.
• Follow Input (with continuous DVI trials) — Output is always authenticated but only
encrypted when required by input. Both HDMI and DVI authentication are continuous.
• Always encrypt output (with continuous DVI trials) — Output is always
authenticated and encrypted. Both HDMI and DVI authentication are continuous.
HAE 100 4K • SIS Commands 10
SIS Commands
This section provides information on:
• Connecting a Control Computer
• Simple Instruction Set (SIS) Control
• Command and Response Table for SIS Commands
Connecting a Control Computer
Connect a control PC to the front panel config port using a USB cable (see “Front Panel
Features” on page 3). Remote communications are via SIS commands (see page 12). Use
a communication utility, such as Extron DataViewer, to send SIS commands and view the
responses.
Simple Instruction Set (SIS) Control
Host-to-Interface Communications
SIS commands consist of one or more characters per field. No special characters are
required to begin or end a command sequence. When a command is valid, the interface
executes the command and sends a response to the host device. All responses from the
interface to the host end with a carriage return and a line feed (CR/LF =
]
), which signals
the end of the response character string. A string is one or more characters.
Error Responses
When the HAE 100 4K receives a valid SIS command, it executes the command and
sends a response to the host device. If the HAE 100 4K is unable to execute the command
because the command is invalid or it contains invalid parameters, it returns an error
response to the host.
The error response codes and their descriptions are as follows:
E10 – Invalid command
E13 – Invalid parameter
Timeout
Pauses of 10 seconds or longer between command ASCII characters result in a timeout.
The command operation is aborted with no other indication.
Using the Command and Response Table
The “Command and Response Table for SIS Commands” is on page 13. Command
and response examples are shown throughout the table. Symbols are used throughout the
table to represent variables in the command and response fields. Use the ASCII to HEX
conversion table on the next page with the command and response table.
HAE 100 4K • SIS Commands 11
ASCII to HEX Conversion Table
Space
.
Symbol definitions
•
= Space
]
= Carriage return with line feed
}
= Carriage return with no line feed (used interchangeably with the pipe character, |)
|
= Pipe (vertical bar) character (used interchangeably with the carriage return with
no line feed character,
}
)
E
= Escape key (used interchangeably with the <W> key)
X!
= Input audio status:
0 = No audio detected or detected audio is not supported
1 = S/PDIF Bitstream audio detected
2 = 2-Ch LPCM detected
X@
= Video mute:
0 = off (default)
1 = video only
2 = video + sync
X#
= 0 = off, disabled or not detected
1 = on, enabled, or detected
X$
= Output HDCP mode:
0 = Encrypt as required by input. Continuous trials for HDMI sinks, attempt
for 10s on DVI sinks (then fail) (default)
1 = Always encrypt. Continuous trials for HDMI sinks, attempt for 10s on
DVI sinks (then fail).
2 = Encrypt as required by input. Continuous trials for HDMI and DVI sinks.
3 = Always encrypt. Continuous trials for HDMI and DVI sinks.
X%
= Output TMDS format:
0 = Auto (default)
1 = DVI RGB 444 Full
2 = HDMI RGB Full
3 = HDMI RGB Limited
4 = HDMI YUV 444 Limited
5 = HDMI YUV 422 Limited
X^
= Slot # on EDID lookup table (1-15), default = 8 (see table on page 6)
X&
= 128 or 256 Byte EDID raw HEX (text form) from currently assigned EDID
X*
= Native resolution and refresh rate from currently assigned EDID
Ex: 1920x1080 @60 Hz
X(
= Output color bit depth:
0= auto based on sink EDID (default)
1= force 8-bit/color
HAE 100 4K • SIS Commands 12
X1)
= Verbose mode:
0 = clear/none
1 = verbose mode (default)
2 = tagged responses for queries
3 = verbose mode and tagged responses for queries
X1!
= Input audio type
1 = 2-Ch LPCM (default)
2 = S/PDIF supported formats
X1@
= Analog audio output configuration:
1 = Stereo (default)
2 = Dual Mono
X1#
= Device name
NOTE: The name is a text string of up to 24 characters drawn from the
alphabet (A-Z), digits (0-9), and minus sign/hyphen (-). No blank or space
characters are permitted as part of a name. The first letter must a letter,
and the last character must not be a minus sign/hyphen. The factory
default is “HAE-100-4K”.
X1$
= Audio output:
1 = Analog output
2 = S/PDIF output
3 = HDMI (embedded) output
X1%
= Input HDCP status:
0 = No active video source detected
1 = Video detected without HDCP (not encrypted)
2 = Video detected with HDCP (encrypted)
X1^
= Output HDCP status:
0 = No sink detected
1 = Non-HDCP sink detected (sink is not HDCP compliant)
2 = HDCP sink detected not encrypted
3 = HDCP sink detected and encrypted
X1&
= Output 5V mode:
0 = Auto
NOTE: 5 V is enabled when a source with 5 V is present; otherwise, it is off.
1 = 5 V always enabled (default)
HAE 100 4K • SIS Commands 13
Command and Response Table for SIS Commands
Command ASCII
Command
(host to unit)
Response
(unit to host)
Additional Description
Signal status
Input/Output Signal Status
E
0LS
} X#
•
X#]
Sig
X#
•
X#]
Input•Output
Verbose mode 2/3
Input HDCP Status
E
IHDCP
} X1%]
HdcpI
X1%]
Verbose mode 2/3
Output HDCP Status
E
OHDCP
} X1^]
HdcpO
X1^]
Verbose mode 2/3
Input Audio Status
1S
AudI
X!]
2 = 2Ch Audio, 1 = Multi-Ch audio,
0 = no audio
Video
Video Mute
X@
B Vmt
X@]
Video Mute Status
B
X@]
Vmt
X@]
Verbose mode 2/3
Input HDCP Authorization
E
E
X#
HDCP
}
HdcpE
X#]
HDCP Authorization Status
E
EHDCP
} X#]
HdcpE
X#]
Verbose mode 2/3
Output HDCP Mode
E
S
X$
HDCP
}
HdcpS
X$]
Output HDCP Mode Status
E
SHDCP
} X$]
HdcpS
X$]
Verbose mode 2/3
Output TMDS Format
EX%
VTPO
}
Vtpo
X%]
Output TMDS Format Status
E
VTPO
} X%]
Vtpo
X%]
Verbose mode 2/3
Output Color Bit Depth
E
V
X(
BITD
}
BitdV
X(]
Output Color Bit Depth Status
E
VBITD
} X(]
BitdV
X(]
Verbose mode 2/3
Set Output Hot-Plug Mode (5V)
E
M
X1&
HPLG
}
HplgM
X1&]
Output Hot-Plug Mode (5V) Status
E
MHPLG
} X1&]
HplgM
X1&]
Audio
Set Input Audio Format
E
I
X1!
AFMT
}
AfmtI
X1!] X1!
= 1 (2-Ch LPCM – default),
2 (S/PDIF supported formats)
View Input Audio Format
E
IAFMT
} X1!]
AfmtI
X1!]
Verbose mode 2/3
Set Analog Output Configuration
E
O
X1@
AFMT
}
AfmtO
X1@] X1@
= 1 (stereo – default), 2 (dual
mono)
View Analog Output Configuration
E
OAFMT
} X1@]
AfmtO
X1@]
Verbose mode 2/3
Audio Mute Per Output
X1$
*
X#
Z Amt
X1$
*
X#] X1$
= 1 (analog), 2 (S/PDIF), 3
(HDMI)
Audio Mute All Outputs
X#
Z Amt
X#]
View Audio Mute Status
Z
X#
•
X#
•
X#]
Amt
X#
•
X#
•
X#]
Analog • S/PDIF • HDMI
Verbose mode 2/3
HAE 100 4K • SIS Commands 14
Command ASCII
Command
(host to unit)
Response
(unit to host)
Additional Description
EDID Minder
Assign EDID Slot to Input
E
A
X^
EDID
}
EdidA
X^]
View EDID Assignment
E
AEDID
} X^]
EdidA
X^]
Verbose mode 2/3
View EDID in HEX format
E
REDID
} X&]
HEX data from currently assigned
EDID
View EDID Native Rate
Example:
E
NEDID
} X*]
[email protected]
Info/Other
Information
I
AudI
X#
•
Sig
X#
•
X#
•
HdcpI
X1%
•
HdcpO
X1^]
Input audio, input/output signal,
and HDCP status
Set Verbose Mode
EX1)
CV
}
Vrb
X1)]
Verbose Mode Status
E
CV
} X1)]
Vrb
X1)]
Verbose mode 2/3
Set Unit Name
EX1#
CN
}
Ipn
•
X1#]
Set Unit Name to Default
E
•
CN
}
Ipn
•
HAE-100-4K
]
View Unit Name
E
CN
} X1#]
Query Part Number
N
60-1542-01
]
Query Model Name
1I
HAE-100-4K
]
Inf01*HAE-100-4K
]
Verbose mode 2/3
Query Model Description
2I HDMI Audio
De-Embedder
]
Inf02*HDMI Audio De-
Embedder
]
Verbose mode 2/3
Query Firmware Version
Q
x.xx
]
Query Firmware Version with Build
*Q
x.xx.xxxx
]
HAE 100 4K • Reference Information 15
Reference
Information
This section contains mounting information and updating firmware methods. Topics in this
section include:
• Mounting
• PCS Software
• Updating Firmware with Firmware Loader
Mounting
Tabletop Placement
Attach the four provided rubber feet to the bottom of the unit and place it in any convenient
location.
Rack Mounting
UL Guidelines for Rack Mounting
The following Underwriters Laboratories (UL) guidelines are relevant to the safe installation of
these products in a rack:
1. Elevated operating ambient temperature — If the unit is installed in a closed or
multi-unit rack assembly, the operating ambient temperature of the rack environment
may be greater than room ambient temperature. Therefore, install the equipment in an
environment compatible with the maximum ambient temperature
(TMA = +122 °F, +50°C) specified by Extron.
2. Reduced air flow — Install the equipment in the rack so that safe operation and
adequate air flow is provided to the unit.
3. Mechanical loading — Mount the equipment in the rack so that a hazardous
condition is not achieved due to uneven mechanical loading.
4. Circuit overloading — Connect the equipment to the supply circuit and consider the
effect that circuit overloading might have on overcurrent protection and supply wiring.
Consider the equipment nameplate ratings when addressing this concern.
5. Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted
equipment. Pay particular attention to supply connections other than direct
connections.
Rack Mounting Procedure
These units can be mounted an optional rack systems listed on the website (see
www.extron.com). To mount the unit on a rack shelf, follow the instructions provided with
the shelf accessories.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25

Extron HAE 100 4K Manuel utilisateur

Extron
Marque
Extron
Modèle
HAE 100 4K
Catégorie
Commutateurs vidéo
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes