Tripp Lite SMART750TSU & SMART1050TSU Le manuel du propriétaire

Marque: Tripp Lite

Modèle: SMART750TSU & SMART1050TSU

Catégorie: Alimentations sans interruption (UPS)

Taper: Le manuel du propriétaire

UPS Systems

Models:

SMART750TSU, SMART1050TSU

(Series Numbers: AG-888F, AG-8890)

Owner’s Manual

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Español 13 • Français 25

PROTECT YOUR INVESTMENT!

You could also win an ISOBAR6ULTRA surge protector—a $100 value!

www.tripplite.com/warranty

18-12-064-933901.indb 1 1/9/2019 5:01:22 PM

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the

installation, operation, maintenance and storage of the UPS and batteries. Failure

to heed these warnings may affect the warranty.

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, conductive contaminants, dust

or direct sunlight.

• For best performance, keep the indoor temperature between 32º F and 104º F

(0º C and 40º C).

• Leave adequate space around all sides of the UPS for proper ventilation.

• Only set the UPS upright on a sturdy ﬂat surface. Do not block fans or ventilation holes, as

this will seriously inhibit the unit's internal cooling and cause product damage not covered

under warranty.

UPS Connection Warnings

• Connect your UPS directly to a properly-grounded AC power outlet. Do not plug the UPS into

itself; this will damage the UPS.

• Do not modify the UPS plug, and do not use an adapter that would eliminate the UPS

ground connection.

• Do not use extension cords to connect the UPS to an AC outlet.

• If the UPS receives power from a motor-powered AC generator, the generator must provide

clean, ﬁltered, computer-grade output.

• The mains socket outlet that supplies the UPS should be easily accessible and located near

the UPS.

Equipment Connection Warnings

Install in accordance with National Electrical Code standards ANSI/NFPA

70 and Canadian Electrical Code, Part I, C22.1.

Short-circuit backup protection and overcurrent protection is provided by

the building installation.

To reduce the risk of ﬁre, connect only to a circuit provided branch circuit

overcurrent protection in accordance with the National Electrical Code,

ANSI/NFPA 70 and the Canadian Electrical Code, Part I, C22.1. The plug on

the power supply cord is intended to serve as the disconnect device. Be

sure that the socket-outlet is installed near the equipment and is made

easily accessible.

Important Safety Instructions

18-12-064-933901.indb 2 1/9/2019 5:01:23 PM

Important Safety Instructions

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to signiﬁcantly

affect its safety or effectiveness is not recommended.

• Do not connect surge protectors or extension cords to the output of your UPS. This might

damage the UPS and may affect the surge protector and UPS warranties.

• Connect the UPS to an outlet that is adequately protected against excess currents, short

circuits and earth faults as part of the building installation.

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current.

Observe proper precautions. There are no user-serviceable parts inside the UPS. Do not

open the UPS except to perform battery replacement. Do not open batteries. Do not

short or bridge the battery terminals with any object. Do not dispose of batteries in a ﬁre.

The batteries may explode. Released material is harmful to the skin and eyes. It may be

toxic. Unplug and turn off the UPS before performing battery replacement. Use tools with

insulated handles. Battery replacement should be performed only by authorized service

personnel using the same number and type of batteries (sealed lead-acid). Do not dispose

of the batteries in a ﬁre. Tripp Lite offers a complete line of UPS System Replacement

Battery Cartridges (R.B.C.).Visit Tripp Lite on the Web at www.tripplite.com/products/battery-

ﬁnder to locate the speciﬁc replacement battery for your UPS.

CAUTION: A battery can present a risk of electrical shock and high short-

circuit current. Contact with any part of a grounded battery can result in

electrical shock. The following precautions should be observed when working

on batteries:

• Remove watches, rings or other metal objects.

• Use tools with insulated handles.

• Wear rubber gloves and boots.

• Do not lay tools or metal parts on top of batteries.

• Disconnect charging source and load prior to installing or maintaining the battery.

• Remove battery grounds during installation and maintenance to reduce likelihood

of shock.

• Remove the connection from ground if any part of the battery is determined to be

grounded.

UPS and Battery Recycling

Tripp Lite products use sealed lead-acid batteries, which are highly recyclable.

Call Tripp Lite at 1.773.869.1234 or visit www.tripplite.com/support/recycling-

program for more information on recycling the batteries or any other Tripp Lite

product. Please refer to local codes for disposal requirements.

18-12-064-933901.indb 3 1/9/2019 5:01:23 PM

STEP 1: Plug the UPS into

a properly grounded outlet.

After plugging the UPS into a wall outlet, press

and hold the power button until the alarm starts to

sound, then release to turn on the UPS.

Note: The UPS will not turn on automatically in the

presence of live utility power.

STEP 2: Plug your equipment

into the UPS.

There are two sets of outlets on the back of your

UPS. Outlets marked SURGE PROTECTED do not

provide battery backup power during power outages.

Connect common desktop items like printers,

scanners and other accessories not requiring

battery support to these outlets. Outlets marked

BATTERY/SURGE PROTECTED offer UPS battery

backup support during power failures. Connect your

vital computer equipment into these outlets.

Your UPS is designed to support electronic

equipment only. You will overload the UPS

if the total volt-amp (VA) ratings for all the

equipment connected to the BATTERY/SURGE

PROTECTED outlets exceed the UPS output

capacity. To ﬁnd your equipment’s VA ratings,

look on their nameplates. If the equipment is

listed in amps (A), multiply the number of amps

by 120 to determine VA. For example: 1A ×

120 = 120VA.

If the color LCD panel does not illuminate when the

UPS is turned ON, try the following:

1. Make sure that the UPS is plugged into a live AC

outlet.

2. Press the power button to turn on the UPS. A

beep should sound when the UPS starts.

3. If the UPS still does not start, contact Tripp Lite

Tech Support for assistance.

Quick Installation

18-12-064-933901.indb 4 1/9/2019 5:01:23 PM

Quick Installation

Optional Installation

All models include a USB communication port

and tel/DSL/Ethernet surge protection jacks (not

compatible with PoE applications). Select models

will also include an RS-232 serial port. These

connections are optional, as the UPS will work

properly without them.

Basic Operation

UPS ON/OFF

• Plug the UPS into a live, grounded outlet.

The entire LCD screen will illuminate for 5 seconds, then the display will report output

voltage of “0V”. The BATTERY / SURGE PROTECTED outlets will be OFF and the SURGE

ONLY outlets will be ON. The battery charger will engage as necessary.

• Plug equipment into the UPS: You will overload the UPS if the total volt-amp (VA) ratings

for all the equipment connected to the BATTERY/SURGE PROTECTED outlets exceed the

UPS output capacity. To ﬁnd your equipment’s VA ratings, look on their nameplates. If the

equipment is listed in amps (A), multiply the number of amps by 120 to determine VA. For

example: 1A × 120 = 120VA.

• Turn the UPS on: Press and hold the power button until the alarm begins to sound, then

release. The UPS alarm will beep once brieﬂy. The BATTERY/SURGE PROTECTED outlets

will begin passing AC line power. The UPS will automatically recharge internal batteries

as needed. Once turned on, your UPS is ready to protect connected equipment from

blackouts, brownouts, overvoltages and transient surges.

• Turn the UPS off: Press the power button.

Note: The UPS system will function properly upon initial startup; however, maximum runtime for the unit’s

battery will only be accessible after it has been charged for 24 hours.

18-12-064-933901.indb 5 1/9/2019 5:01:23 PM

Basic Operation

Display UPS/Power Conditions

On-Line AC Power Mode LCD Data

The LCD touchscreen offers 5 screens of UPS and site power information when the UPS

is operating in on-line power mode. Screens 1-4 (Output Voltage, Input Voltage, Load %,

Battery Charge Level) are available for viewing in on-line power mode. Press the front panel

LCD to advance to the next screen. Screen #5 (Overload) is displayed automatically only

when the UPS is loaded to levels greater than 100%.

The LCD screen reports that AVR (Auto Voltage Regulation) buck/boost circuits are active any

time the on-line power symbol is ﬂashing.

Output Voltage

Input Voltage

Load %

Battery Charge Level

Overload

Operating Mode Alarm Description

Battery Mode Normal No Alarm

Battery Low Sounds Every Second

Overload Sounds Every 0.5 Second

On-Line Mode Normal No Alarm

Overload Sounds Every 0.5 Second

Battery Replace Sounds Every Minute

Fault Mode Sounds Continuously

Note: The LCD touchscreen automatically turns off in on-line power mode 20 seconds after it was last

touched. To re-activate the LCD for an additional 20 seconds, touch the screen.

18-12-064-933901.indb 6 1/9/2019 5:01:23 PM

Basic Operation

Battery Power Mode LCD Data

The LCD touchscreen offers 5 screens of UPS and site power information when the UPS

is operating in battery power mode. Screens 1-4 (Output Voltage, Input Voltage, Load %,

Battery Charge Level) are available for viewing in battery power mode. Press the front panel

LCD to advance to the next screen. Screen #5 (Overload) is displayed automatically only

when the BATTERY/SURGE PROTECTED outlets are loaded to levels greater than 100%.

Critical Fault Screens

Error Code Critical Fault Solution

F01 OUTPUT SHORT Disconnect load(s) from UPS outlets. Power off UPS and

contact Tripp Lite Technical Support for assistance.

F02 OVERLOAD Remove excess load, check load meter on LCD for load

status.

F03 OVERCHARGE Turn unit off, unplug UPS and contact Tripp Lite

Technical Support for assistance.

F04 BATTERY LOW

VOLTAGE

Charge UPS for 24 hours. If problem persists, replace

battery and contact Tripp Lite Technical Support if

problem persists.

F05 BATTERY MODE

HIGH OUTPUT

Turn off power to the UPS and contact Tripp Lite

Technical Support for assistance.

Output Voltage

Input Voltage

Load %

Battery Charge Level

Overload

Note: The LCD touchscreen will remain ON continuously during battery mode operation.

18-12-064-933901.indb 7 1/9/2019 5:01:24 PM

Features

UPS Features

All Models

18-12-064-933901.indb 8 1/9/2019 5:01:24 PM

Features

ON/OFF Button: When the UPS is OFF, press and hold the ON/OFF button until a beep

is heard to turn the UPS ON. When the UPS is ON, press and hold the ON/OFF button to

turn the UPS OFF.

LCD Touchscreen Panel: Provides current status of the UPS. For a detailed description,

refer to “Display UPS/Power Conditions” in the Basic Operation section.

Battery Backup/Surge Protected Outlets: These outlets offer battery backup support

and premium surge suppression for critical devices requiring battery backup support.

Surge Protected Outlets: These outlets offer premium surge suppression for critical

devices.

USB and RS-232* Communication Ports: These port can connect your UPS to

any computer for automatic saves and unattended shutdown in the event of a power

failure. Use with Tripp Lite’s PowerAlert

Software (available as a FREE download at

www.tripplite.com) and the USB cable included with your UPS. These connections are

optional, your UPS will work properly without this connection.

*All models include a USB communication port. Select models also include an RS-232 serial port.

Note: This UPS System provides basic communication compatibility with most integrated Windows

Macintosh

and Linux

power management applications.

Tel/DSL/Ethernet Line Protection Jacks: These jacks protect equipment against surges

over a single phone line or network connection. Connecting your equipment to these

jacks is optional; your UPS will work properly without this connection.

Note: Not compatible with PoE (Power over Ethernet) applications.

Resettable Input Circuit Breaker: Protects your electrical circuit from overcurrent draw

from the UPS load. If this breaker trips, remove some of the load, then reset by pressing

it in.

Fan: Provides cooling during AVR mode or when the UPS is operating in battery mode.

18-12-064-933901.indb 9 1/9/2019 5:01:24 PM

Storage

To avoid battery drain, all connected equipment should be turned off and disconnected from

the UPS. Press the power button and disconnect the unit from AC power. Your UPS will be

completely turned off (deactivated), and will be ready for storage. If you plan on storing your

UPS for an extended period, fully recharge the UPS batteries every three months. Plug the

UPS into a live AC outlet and allow the batteries to recharge for 4 to 6 hours. If you leave

your UPS batteries discharged for a long period of time, they will suffer a permanent loss of

capacity.

Storage and Service

Battery Replacement

Under normal conditions, the original battery in your UPS will last several years. Battery

replacement should only be performed by qualiﬁed personnel. Refer to “Battery Warnings” in

the Important Safety Instructions section for more information.

All models require two 12V DC, 9Ah replacement batteries (Tripp Lite model: RBC51).

For further information about replacement compatibility and ordering, visit

www.tripplite.com/products/battery-ﬁnder.

Battery replacement must be done using the same battery type and

quantity: 12V DC sealed lead-acid, 6-cell and in compliance with UL 1989.

CAUTION: Risk of energy hazard. Before replacing batteries, remove

conductive jewelry such as chains, wristwatches and rings. High energy

passing through conductive materials may cause severe burns.

18-12-064-933901.indb 10 1/9/2019 5:01:24 PM

Storage and Service

Product Registration

Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a

drawing for a chance to win a FREE Tripp Lite product! *

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

Service

A variety of Extended Warranty and On-Site Service Programs are available from Tripp Lite. For

more information on service, visit www.tripplite.com/support.

Before returning your product for service, follow these steps:

1. Review the installation and operation procedures in this manual to ensure that the service

problem does not originate from a misreading of the instructions.

2. If the problem continues, do not contact or return the product to the dealer. Instead, visit

www.tripplite.com/support.

3. If the problem requires service, visit www.tripplite.com/support and click the Product

Returns link. From here you can request a Returned Material Authorization (RMA) number,

which is required for service. This simple on-line form will ask for your unit’s model and

serial numbers, along with other general purchaser information. The RMA number, along

with shipping instructions, will be emailed to you. Any damages (direct, indirect, special

or consequential) to the product incurred during shipment to Tripp Lite or an authorized

Tripp Lite service center is not covered under warranty. Products shipped to Tripp Lite or an

authorized Tripp Lite service center must have transportation charges prepaid. Mark the

RMA number on the outside of the package. If the product is within its warranty period,

enclose a copy of your sales receipt. Return the product for service using an insured

carrier to the address given to you when you request the RMA.

FCC Part 68 Notice (United States Only)

If your Modem/Fax Protection causes harm to the telephone network, the telephone company may temporarily

discontinue your service. If possible, they will notify you in advance. If advance notice isn’t practical, you will be

notiﬁed as soon as possible. You will be advised of your right to ﬁle a complaint with the FCC. Your telephone

company may make changes in its facilities, equipment, operations or procedures that could affect the proper

operation of your equipment. If it does, you will be given advance notice to give you an opportunity to maintain

uninterrupted service. If you experience trouble with this equipment’s Modem/Fax Protection, please visit www.

tripplite.com/support for repair/warranty information. The telephone company may ask you to disconnect

this equipment from the network until the problem has been corrected or you are sure the equipment is not

malfunctioning. There are no repairs that can be made by the customer to the Modem/Fax Protection. This

equipment may not be used on coin service provided by the telephone company. Connection to party lines is

subject to state tariffs. (Contact your state public utility commission or corporation commission for information.)

Regulatory Compliance

18-12-064-933901.indb 11 1/9/2019 5:01:24 PM

Note on Labeling

Two symbols are used on the label.

V~ : AC Voltage

V : DC Voltage

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Regulatory Compliance

FCC Notice, Class A

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING: Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

Equipment Attachment Limitations (models with the Industry Canada label in Canada only)

NOTICE: The Industry Canada label identiﬁes certiﬁed equipment. This certiﬁcation means that the equipment

meets the telecommunications network protective, operational and safety requirements as prescribed in the

appropriate Terminal Equipment Technical Requirements Document(s). The Department does not guarantee the

equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is

permissible to be connected to the facilities of the local telecommunications company. The equipment must also

be installed using an acceptable method of connection. The customer should be aware that the compliance with

the above conditions might not prevent degradation of service in some situations.

Repairs to certiﬁed equipment should be coordinated by a representative designated by the supplier. Any repairs

or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications

company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone

lines and internal metallic water pipe system, if present, are connected together. This precaution may be

particularly important in rural areas. Caution: Users should not attempt to make connections themselves, but

should contact the appropriate electric inspection authority, or electrician, as appropriate.

Regulatory Compliance Identiﬁcation Numbers

For the purpose of regulatory compliance certiﬁcations and identiﬁcation, your Tripp Lite product has been

assigned a unique series number. The series number can be found on the product nameplate label, along with

all required approval markings and information. When requesting compliance information for this product, always

refer to the series number. The series number should not be confused with the marking name or model number of

the product.

Tripp Lite has a policy of continuous improvement. Product speciﬁcations are subject to change without notice.

18-12-064-933901.indb 12 1/9/2019 5:01:24 PM

Sistemas UPS

Modelos:

SMART750TSU, SMART1050TSU

(Números de Serie: AG-888F, AG-8890)

Manual del Propietario

1111 W. 35th Street, Chicago, IL 60609 EE UU • www.tripplite.com/support

English 1 • Français 25

18-12-064-933901.indb 13 1/9/2019 5:01:24 PM

CONSERVE ESTAS INSTRUCCIONES

Este manual contiene instrucciones y advertencias que deben seguirse durante

la instalación, operación, mantenimiento y almacenamiento del UPS y baterías. El

incumplimiento de estas advertencias puede afectar la garantía.

Advertencias para la Ubicación del UPS

• Instale su UPS en interiores, alejado de humedad o calor excesivos, contaminantes

conductores, polvo o luz solar directa.

• Para mejor desempeño, mantenga la temperatura interior entre 0 ºC y 40 ºC

[32 ºF y 104 ºF].

• Deje espacio adecuado alrededor de todos los lados del UPS para una ventilación

apropiada.

• Sólo ponga el UPS en posición vertical sobre una superﬁcie plana sólida. No bloquee los

ventiladores o los oriﬁcios de ventilación, ya que inhibirá seriamente el enfriamiento interno

de la unidad y causará daños no cubiertos por la garantía.

Advertencias para la Conexión del UPS

• Conecte su UPS directamente a un tomacorrientes de CA conectado correctamente a

tierra. No enchufe el UPS en sí mismo; esto dañará al UPS.

• No modiﬁque la clavija del UPS y no use un adaptador que pueda eliminar la conexión a

tierra del UPS.

• No use cables de extensión para conectar el UPS a un tomacorrientes de CA.

• Si el UPS recibe alimentación de un generador de CA activado por motor, debe probarse

que el generador proporciona una salida de grado computadora, limpia y ﬁltrada.

• El tomacorrientes que alimenta al UPS debe ser fácilmente accesible y estar cerca del UPS.

Advertencias para la Conexión del Equipo

Instale de acuerdo con los estándares del Código Eléctrico Nacional ANSI /

NFPA 70 y Código Eléctrico Canadiense, Parte I, C22.1.

La protección de respaldo por corto circuito y la protección contra

sobrecorriente es proporcionada por la instalación del ediﬁcio.

Para reducir el riesgo de incendio, conecte solamente a un circuito

provisto de una protección contra sobrecorrientes del circuito derivado

según el Código Eléctrico Nacional, ANSI/NFPA 70 y el Código Eléctrico

Canadiense, Parte I, C22.1. La clavija en el cable de alimentación está

diseñada para servir como dispositivo de desconexión. Asegúrese que

el tomacorrientes esté instalado cerca del equipo y sea fácilmente

accesible.

Instrucciones de Seguridad Importantes

18-12-064-933901.indb 14 1/9/2019 5:01:24 PM

Instrucciones de Seguridad

Importantes

• No se recomienda el uso de este equipo en aplicaciones de soporte de vida en donde

razonablemente se pueda esperar que la falla de este equipo cause la falla del equipo de

soporte de vida o afectar signiﬁcativamente su seguridad o efectividad.

• No conecte supresores de sobretensiones o cables de extensión a la salida de su UPS.

Esto puede dañar al UPS y afectar las garantías del supresor de sobretensiones y del UPS.

• Conecte el UPS a un tomacorrientes que esté adecuadamente protegido contra corrientes

excesivas, cortocircuitos, y fallas de conexión a tierra como parte de la instalación del

ediﬁcio.

Advertencias de la Batería

• Las baterías pueden presentar un riesgo de descarga eléctrica y quemaduras por la alta

corriente de corto circuito. Observe las precauciones apropiadas. No hay partes dentro

del UPS a las que el usuario pueda dar servicio. No abra el UPS, excepto para realizar el

reemplazo de la batería. No abra las baterías. No ponga en corto o puentee las terminales

de la batería con ningún objeto. No deseche las baterías en el fuego. Las baterías pueden

explotar. El material liberado es dañino a la piel y ojos. Puede ser tóxico. Desenchufe y

apague el UPS antes de reemplazar la batería. Use herramientas con mangos aislados. El

reemplazo de la batería debe realizarlo solo el personal de servicio autorizado usando el

mismo número y tipo de baterías (Plomo-Ácido Selladas). No deseche las baterías en el

fuego. Tripp Lite ofrece una línea completa de Cartuchos de Batería de Repuesto (R.B.C.)

para Sistemas UPS. Para localizar la batería de repuesto especíﬁca para su UPS, visite

Tripp Lite en el sitio www.tripplite.com/products/battery-ﬁnder.

PRECAUCIÓN: Una batería puede presentar un riesgo de descarga eléctrica

y alta corriente de cortocircuito. Hacer contacto con cualquier parte de una

batería conectada a tierra puede causar una descarga eléctrica. Al trabajar

con baterías deben observarse las siguientes precauciones:

• Retire relojes, anillos u otros objetos metálicos.

• Use herramientas con mangos aislados.

• Use botas y guantes de hule.

• No coloque herramientas o partes metálicas sobre la parte superior de las

baterías.

• Desconecte la fuente de carga y la carga antes de la instalación o el

mantenimiento de la batería.

• Elimine las conexiones a tierra de la batería durante la instalación y mantenimiento

para reducir la probabilidad de descarga.

• Quite la conexión a tierra si se determina que cualquier parte de la batería debe

estar conectada a tierra.

Reciclado de la batería y el UPS

Los productos de Tripp Lite usan baterías selladas de plomo-ácido, que son

altamente reciclables.

Llame a Tripp Lite al 1.773.869.1234 o visite www.tripplite.com/support/recycling-

program para obtener información adicional sobre el reciclado de baterías u otro

producto de Tripp Lite. Para los requisitos de desecho, por favor consulte sus

códigos locales.

18-12-064-933901.indb 15 1/9/2019 5:01:25 PM

PASO 1: Enchufe el UPS en un

tomacorriente correctamente

aterrizado.

Después de enchufar el UPS en un tomacorriente

de pared, presione y sostenga el botón de

encendido durante un segundo hasta que la alarma

empiece a sonar y suéltelo para encender el UPS.

Nota: El UPS no encenderá automáticamente en

presencia de energía activa de la red pública.

PASO 2: Enchufe su equipo en

el UPS.

Hay dos juegos de tomacorrientes en la parte

posterior de su UPS. Los tomacorrientes marcados

SURGE PROTECTED no proporcionan respaldo de

energía por batería durante apagones. Conecte

en estos tomacorrientes los equipos de escritorio

comunes como impresoras, escáneres y otros

accesorios que no requieran respaldo por batería.

Los tomacorrientes marcados BATTERY / SURGE

PROTECTED ofrecen respaldo por batería del

UPS durante fallas de energía. Conecte en estos

tomacorrientes sus equipos de cómputo vitales.

Su UPS está diseñado para soportar solamente

equipo electrónico. Usted sobrecargará el

UPS si el valor total en volt-amperes (VA) para

todo el equipo conectado a los tomacorrientes

BATTERY / SURGE PROTECTED excede la

capacidad de salida del UPS. Para localizar

los valores de VA de su equipo, consulte las

placas de identiﬁcación. Si el equipo está

especiﬁcado en amperes (A), multiplique el

número de amperes por 120 para determinar

VA. Por ejemplo: 1A × 120 = 120VA.

Si el panel LCD de color no se ilumina cuando se

enciende el UPS, intente lo siguiente:

1. Asegúrese de que el UPS esté conectado a un

tomacorrientes de CA.

2. Presione el botón de encendido para encender

el UPS. Sonará un bip cuando el UPS arranque.

3. Si el UPS aún no arranca, póngase en contacto

con Soporte Técnico de Tripp Lite para solicitar

apoyo.

Instalación Rápida

18-12-064-933901.indb 16 1/9/2019 5:01:25 PM

Instalación Rápida

Instalación Opcional

Todos los modelos incluyen un puerto de

comunicación USB y conectores de supresión de

sobretensiones Tel / DSL / Ethernet (no compatible

con aplicaciones PoE). Modelos selectos también

incluirán un puerto serial RS-232. Estas conexiones

son opcionales, el UPS funcionará adecuadamente

sin ellas.

Operación Básica

ENCENDIDO Y APAGADO DEL UPS

• Enchufe el UPS en un tomacorrientes activo conectado a tierra.

Toda la pantalla LCD se iluminará durante 5 segundos, después la pantalla informará el

voltaje de salida de “0V”. Los tomacorrientes marcados BATTERY / SURGE PROTECTED se

apagarán y los tomacorrientes SURGE ONLY se encenderán. El cargador de la batería se

activará según sea necesario.

• Enchufe el equipo en el UPS: Usted sobrecargará el UPS si el valor total en Volts

Amperes (VA) para todo el equipo conectado a los tomacorrientes BATTERY / SURGE

PROTECTED excede la capacidad de salida del UPS. Para localizar los valores de VA de su

equipo, consulte las placas de identiﬁcación. Si el equipo está especiﬁcado en amperes

(A), multiplique el número de amperes por 120 para determinar VA. Por ejemplo:

1A × 120 = 120VA.

• Encienda el UPS: Oprima y sostenga el botón de encendido hasta que la alarma empiece

a sonar, luego suéltelo. La alarma del UPS emitirá un bip brevemente. Los tomacorrientes

BATTERY/SURGE PROTECTED empezarán a pasar energía de la línea de CA. El UPS

recargará automáticamente las baterías internas según sea necesario. Una vez encendido,

su UPS está listo para proteger los equipos conectados contra apagones, caídas de voltaje,

sobrevoltajes y sobretensiones transientes.

• Apague el UPS: Presione el botón de alimentación.

Nota: El sistema UPS funcionará correctamente en el arranque inicial; sin embargo, la autonomía máxima

para la batería de la unidad sólo será accesible después de haberse cargado por 24 horas.

18-12-064-933901.indb 17 1/9/2019 5:01:25 PM

Operación Básica

Muestra las Condiciones del UPS / Energía

Datos del LCD de Modo de Alimentación de CA En Línea

La pantalla LCD táctil ofrece 5 pantallas de información de la energía del UPS y el sitio

cuando el UPS esté operando en modo de alimentación en línea. Pantallas 1 ~ 4 (Voltaje de

Salida, Voltaje de Entrada, % de Carga, Nivel de Carga de la Batería) están disponibles para

visualización en modo de alimentación de línea. Para avanzar a la siguiente pantalla, toque

el LCD de la pantalla frontal. La pantalla #5 (Sobrecarga) se muestra automáticamente solo

cuando el UPS esté cargado a niveles superiores al 100%.

La pantalla del LCD informa que circuitos de reducción y elevación de la AVR (Regulación

Automática de Voltaje) están activos en cualquier momento que el ícono de la alimentación

en línea esté destellando.

Voltaje de Salida

Voltaje de Entrada

% de Carga

Nivel de Carga de la Batería*

Sobrecarga

Modo de Operación Descripción de la Alarma

Modo de en

Respaldo por

Batería

Normal Sin Alarma

Batería Baja Suena Cada Segundo

Sobrecarga Suena Cada 0.5 Segundos

Modo En Línea Normal Sin Alarma

Sobrecarga Suena Cada 0.5 Segundos

Reemplazo de la Batería Suena Cada Minuto

Modo de Falla Suena Continuamente.

Nota: La pantalla LCD táctil se apaga automáticamente en el modo de alimentación en línea 20 segundos

después de la última vez que se tocó. Para volver a activar el LCD por 20 segundos adicionales, toque la pantalla.

18-12-064-933901.indb 18 1/9/2019 5:01:26 PM

Operación Básica

Datos del LCD del Modo de Alimentación por Batería

La pantalla LCD táctil ofrece 5 pantallas de información de la energía del UPS y el sitio

cuando el UPS esté operando en modo de alimentación por batería. Las pantallas 1 ~

4 (voltaje de salida, voltaje de entrada, % de carga, nivel de carga de la batería) están

disponibles para visualización en modo de respaldo por batería. Para avanzar a la siguiente

pantalla, toque el LCD de la pantalla frontal. La pantalla #5 (Sobrecarga) se muestra

automáticamente solo cuando los tomacorrientes BATTERY/SURGE PROTECTED se cargan a

niveles de más de 100%.

Pantallas de Fallas Críticas

Código de

Error Falla Crítica Solución:

F01 CORTO EN LA

SALIDA

Desconecte carga(s) de los tomacorrientes del UPS.

Apague el UPS y póngase en contacto con Soporte

Técnico de Tripp Lite para obtener apoyo.

F02 SOBRECARGA Elimine el exceso de carga, revise el medidor de carga

en el LCD para ver el estado de la carga.

F03 SOBRECARGA Apague la unidad, desenchufe el UPS y póngase en

contacto con el Soporte Técnico de Tripp Lite para

obtener apoyo

F04 VOLTAJE BAJO DE

LA BATERÍA

Cargue el UPS durante 24 horas. Si el problema

persiste, reemplace la batería y póngase en contacto

con el Soporte Técnico de Tripp Lite.

F05 SALIDA ALTA EN

MODO DE BATERÍA

Apague el UPS y póngase en contacto con el Soporte

Técnico de Tripp Lite para obtener apoyo.

Voltaje de Salida

Voltaje de Entrada

% de Carga

Nivel de Carga de la Batería*

Sobrecarga

Nota: La pantalla LCD táctil permanecerá encendida continuamente durante la operación en el modo de

respaldo por batería.

18-12-064-933901.indb 19 1/9/2019 5:01:26 PM

Características

Características del UPS

Todos los Modelos

18-12-064-933901.indb 20 1/9/2019 5:01:26 PM

La page charge ...

Tripp Lite SMART750TSU & SMART1050TSU Le manuel du propriétaire

Marque: Tripp Lite

Modèle: SMART750TSU & SMART1050TSU

Catégorie: Alimentations sans interruption (UPS)

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Tripp Lite SMART750TSU & SMART1050TSU Owner's manual
español: Tripp Lite SMART750TSU & SMART1050TSU El manual del propietario

Tripp Lite SMART750TSU & SMART1050TSU Le manuel du propriétaire

Tripp Lite SMART750TSU & SMART1050TSU Le manuel du propriétaire

dans d''autres langues

Documents connexes