Harmonic ProView 7100 4.0.3 Guide d'installation
- Taper
- Guide d'installation
ProView™
7100
Release 4.x.x
Installation Guide
Revision A
2
Manual Part No. N/A
June 2016
Copyright © 2000–2016 Harmonic Inc. All rights reserved. Harmonic, the Harmonic logo, Omneon, the Omneon logo, [all other Harmonic products
mentioned] are trademarks, registered trademarks or service marks of Harmonic Inc. in the United States and other countries. Dolby, Dolby Digital,
Dolby Digital Plus and Dolby E are registered trademarks of Dolby Laboratories. Implementations of AAC and HE-AAC by Fraunhofer IIS. Other
company, product and service names mentioned herein may be trademarks or service marks of their respective owners. All product and application
features and specifications are subject to change at Harmonic's sole discretion at any time and without notice.
Disclaimer
Harmonic reserves the right to alter the equipment specifications and descriptions in this publication without prior notice. No part of this publication
shall be deemed to be part of any contract or warranty unless specifically incorporated by reference into such contract or warranty. The information
contained herein is merely descriptive in nature, and does not constitute a binding offer for sale of the product described herein. Harmonic assumes
no responsibility or liability arising from the use of the products described herein, except as expressly agreed to in writing by Harmonic. The use and
purchase of this product do not convey a license under any patent rights, copyrights, trademark rights, or any intellectual property rights of Harmonic.
Nothing hereunder constitutes a representation or warranty that using any products in the manner described herein will not infringe any patents of third
parties.
Third-party product trademarks
Adobe® After Effects®, Photoshop®, Flash® Professional, Premiere®
Avid®Media Composer®
Dolby® E, Dolby Digital, Dolby Digital Plus
Jünger Audio™
Apple®QuickTime®
Ericsson Mediaroom
Microsoft® PlayReady®
DOCSIS®3.0
Start Over® TV
Third-party copyright notes
Dolby is a registered trademark of Dolby Laboratories.
Dolby Digital, Dolby Digital Plus, Dolby Pulse, aacPlus, AC-3, and Dolby E are trademarks of Dolby Laboratories.
Level Magic and Jünger are trademarks of Jünger Audio Studiotechnik GmbH.
MPEG Audio technology licensed from Fraunhofer IIS http://www.iis.fraunhofer.de/amm/
PitchBlue® is a registered trademark of Vigor Systems.
QuickTime and the QuickTime logo are trademarks or registered trademarks of Apple Computer, Inc., used under license therefrom.
Harmonic software uses version 3.15.4 of the FreeImage open source image library under FreeImage Public License (FIPL). See http://
freeimage.sourceforge.net for details.
Trademark acknowledgments
Harmonic and all Harmonic product names are trademarks of Harmonic All other trademarks are the property of their respective owners.
The software described in this document is furnished under a license agreement or nondisclosure agreement. The software may be used or copied
only in accordance with the terms of those agreements.
May be covered by one or more of U.S. Patents No. 6,571,351; 6,696,996; 6,545,721; 6,574,225; 6,895,003; 6,522,649; 6,643,702; foreign
counterparts and pending patent applications.
This system is distributed with certain other software that may require disclosure or distribution of licenses, copyright notices, conditions of use,
disclaimers and/or other matter. Use of this system or otherwise fulfilling their conditions constitutes your acceptance of them, as necessary. Copies
of such licenses, notices, conditions, disclaimers and/or other matter are available in any one of the following locations: the LEGAL NOTICES
AND LICENSES directory of the distribution disk of the software, the root directory of the hard disk drive of the Products, or by contacting us at
Notice
Information contained in this guide is subject to change without notice or obligation. While every effort has been made to ensure that the information is
accurate as of the publication date, Harmonic Inc. assumes no liability for errors or omissions. In addition, Harmonic Inc. assumes no responsibility for
damages resulting from the use of this guide.
License agreement and limited warranty
1. AGREEMENT: This is a legal agreement ("Agreement") between you ("you" or "your") and Harmonic, or its appropriate local affiliate ("Harmonic",
"we", "us" or "our"). Use of our product(s) and any updates thereto purchased or validly obtained by you (the "Products"), and/or the Software (as
defined below) (collectively, the "System"), constitutes your acceptance of this Agreement. "Use" includes opening or breaking the seal on the
packet containing this Agreement, installing or downloading the Software as defined below or using the Software preloaded or embedded in your
3 ProView 4.x.x Installation Guide
System. As used herein, the term "Software" means the Harmonic owned software and/or firmware used in or with the Products and embedded
into, provided with or loaded onto the Products in object code format, but does not include, and this Agreement does not address, any third-party
or free or open source software separately licensed to you ("Third Party Software"). If you do not agree to this Agreement, you shall promptly
return the System with a dated receipt to the seller for a full refund.
2. LICENSE: Subject to the terms and conditions of this Agreement (including payment), we hereby grant you a nonexclusive, nontransferable
license to use the object code version of the Software embedded into, provided solely for use with or loaded onto the Product, and the
accompanying documentation ("Documentation") for your internal business purposes. The Software and any authorized copies are owned by us
or our suppliers, and are protected by law, including without limitation the copyright laws and treaties of the U.S.A. and other countries. Evaluation
versions of the Software may be subject to a time-limited license key.
3. RESTRICTIONS: You (and your employees and contractors) shall not attempt to reverse engineer, disassemble, modify, translate, create
derivative works of, rent, lease (including use on a timesharing, applications service provider, service bureau or similar basis), loan, distribute,
sublicense or otherwise transfer the System, in whole or part except to the extent otherwise permitted by law. The Software may be operated
on a network only if and as permitted by its Documentation. You may make one (1) back up copy of the object code of the Software for archival
purposes only. Evaluation Software will be run in a lab, nonproductive environment. Results of any benchmark or other performance tests may
not be disclosed to any third party without our prior written consent. Title to and ownership of the Software and Documentation, and all copyright,
patent, trade secret, trademark, and other intellectual property rights in the System, shall remain our or our licensors' property. You shall not
remove or alter any copyright or other proprietary rights notice on the System. We reserve all rights not expressly granted.
4. LIMITED WARRANTY: (a) Limited Warranty. We warrant to you that, commencing on your receipt of a Product and terminating 1 year thereafter,
the System will perform substantially in accordance with its then-current appropriate Documentation. The Product (including replacements) may
consist of new, used or previously-installed components. (b) Remedies. If the System fails to comply with such warranty during such period,
as your sole remedy, you must return the same in compliance with our product return policy, and we shall, at our option, repair or replace the
System, provide a workaround, or refund the fees you paid. Replacement Systems are warranted for the original System's remaining warranty
period. (c) Exclusions. EVALUATION SOFTWARE IS LICENSED ON AS-IS BASIS AND SUBJECT TO 4(d). We will have no obligation under
this limited warranty due to: (i) negligence, misuse or abuse of the System, such as unusual physical or electrical stress, misuse or accidents; (ii)
use of the System other than in accordance with the Documentation; (iii) modifications, alterations or repairs to the System made by a party other
than us or our representative; (iv) the combination, operation or use of the System with equipment, devices, software or data not supplied by
us; (v) any third party hardware or Third Party Software, whether or not provided by us; (vi) any failure other than by us to comply with handling,
operating, environmental, storage or maintenance requirements for the System in the Documentation, including, without limitation, temperature
or humidity ranges. (d) Disclaimers. We are not responsible for your software, firmware, information, or data contained in, stored on, or integrated
with any Product returned to us for repair or replacement. SUCH LIMITED WARRANTY IS IN LIEU OF, AND WE SPECIFICALLY DISCLAIM,
ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OF SATISFACTORY QUALITY, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT.
WE DO NOT WARRANT THAT THE SYSTEM WILL MEET YOUR REQUIREMENTS OR BE UNINTERRUPTED OR ERROR-FREE. NO
ADVICE OR INFORMATION, WHETHER ORAL OR WRITTEN, OBTAINED FROM US OR ELSEWHERE, WILL CREATE ANY WARRANTY
NOT EXPRESSLY STATED IN THIS AGREEMENT. Some jurisdictions do not allow the exclusion of implied warranties or limitations on how long
an implied warranty may last, so such exclusions may not apply to you. In that event, such implied warranties or limitations are limited to 60 days
from the date you purchased the System or the shortest period permitted by applicable law, if longer. This warranty gives you specific legal rights
and you may have other rights which vary from state to state or country to country.
5. LIMITATION OF LIABILITY: WE AND OUR AFFILIATES, SUPPLIERS, LICENSORS, OR SALES CHANNELS ("REPRESENTATIVES") SHALL
NOT BE LIABLE TO YOU FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR EXEMPLARY DAMAGES OF ANY KIND,
INCLUDING BUT NOT LIMITED TO LOST REVENUES, PROFITS OR SAVINGS, OR THE COST OF SUBSTITUTE GOODS, HOWEVER
CAUSED, UNDER CONTRACT, TORT, BREACH OF WARRANTY, NEGLIGENCE, OR OTHERWISE, EVEN IF WE WERE ADVISED OF
THE POSSIBILITY OF SUCH LOSS OR DAMAGES. NOTWITHSTANDING ANY OTHER PROVISIONS OF THIS AGREEMENT, WE AND
OUR REPRESENTATIVES' TOTAL LIABILITY TO YOU ARISING FROM OR RELATING TO THIS AGREEMENT OR THE SYSTEM SHALL
BE LIMITED TO THE TOTAL PAYMENTS TO US UNDER THIS AGREEMENT FOR THE SYSTEM. THE FOREGOING LIMITATIONS SHALL
NOT APPLY TO DEATH OR PERSONAL INJURY TO PERSONS OR TANGIBLE PROPERTY IN ANY JURISDICTION WHERE APPLICABLE
LAW PROHIBITS SUCH LIMITATION. YOU ARE SOLELY RESPONSIBLE FOR BACKING UP YOUR DATA AND FILES, AND HEREBY
RELEASE US AND OUR REPRESENTATIVES FROM ANY LIABILITY OR DAMAGES DUE TO THE LOSS OF ANY SUCH DATA OR FILES.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO SUCH
EXCLUSIONS MAY NOT APPLY TO YOU.
6. CONFIDENTIALITY: Information in the System and the associated media, as well as the structure, organization and code of the Software, are
proprietary to us and contain valuable trade secrets developed or acquired at great expense to us or our suppliers. You shall not disclose to
others or utilize any such information except as expressly provided herein, except for information (i) lawfully received by the user from a third
party which is not subject to confidentiality obligations; (ii) generally available to the public without breach of this Agreement; (iii) lawfully known to
the user prior to its receipt of the System; or (iv) required by law to be disclosed.
7. SUPPORT: Updates, upgrades, fixes, maintenance or support for the System (an "Upgrade") after the limited warranty period may be available
at separate terms and fees from us. Any Upgrades shall be subject to this Agreement, except for additional or inconsistent terms we specify.
Upgrades do not extend the limited warranty period.
8. TERM; TERMINATION: The term of this Agreement shall continue unless terminated in accordance with this Section. We may terminate this
Agreement at any time upon default by you of the license provisions of this Agreement, or any other material default by you of this Agreement not
cured with thirty (30) days after written notice thereof. You may terminate this Agreement any time by terminating use of the System. Except for
the first sentence of Section 2 ("License") and for Section 4(a) ("Limited Warranty"), all provisions of this Agreement shall survive termination of
this Agreement. Upon any such termination, you shall certify in writing such termination and non-use to us.
9. EXPORT CONTROL: You agree that the Products and Software will not be shipped, transferred, or exported into any country or used in any
manner prohibited by the United States Export Administration Act or any other export laws, restrictions, or regulations (the "Export Laws"). You
will indemnify, defend and hold us harmless from any and all claims arising therefrom or relating thereto. In addition, if the Products or Software
are identified as export controlled items under the Export Laws, you represent and warrant that you are not a citizen, or otherwise located within,
an embargoed nation (including without limitation Iran, Iraq, Syria, Sudan, Libya, Cuba, North Korea, and Serbia) and that you are not otherwise
prohibited under the Export Laws from receiving the Software. All rights to the Products and Software are granted on condition that such rights
are forfeited if you fail to comply with the terms of this Agreement.
10. U.S. GOVERNMENT RIGHTS: The Software and the documentation which accompanies the Software are "Commercial Items," as that term
is defined at 48 C.F.R. §2.101, consisting of "Commercial Computer Software" and "Commercial Computer Software Documentation," as such
4
terms are used in 48 C.F.R. §12.212 or 48 C.F.R. §227.7202, as applicable. Consistent with 48 C.F.R. §12.212 or 48 C.F.R. §§227.7202-1
through 227.7202-4, as applicable, the Commercial Computer Software and Commercial Computer Software Documentation are being licensed
to U.S. Government as end users (a) only as Commercial Items and (b) with only those rights as are granted to all other end users pursuant to
the terms and conditions herein. Harmonic, 4300 North First Street, San Jose, CA 95134, U.S.A.
11. GENERAL: You shall not assign, delegate or sublicense your rights or obligations under this Agreement, by operation of law or otherwise, without
our prior written consent, and any attempt without such consent shall be void. Subject to the preceding sentence, this Agreement binds and
benefits permitted successors and assigns. This Agreement is governed by California law, without regard to its conflicts of law principles. The
U.N. Convention on Contracts for the International Sale of Goods is disclaimed. If any claim arises out of this Agreement, the parties hereby
submit to the exclusive jurisdiction and venue of the federal and state courts located in Santa Clara County, California. In addition to any other
rights or remedies, we shall be entitled to injunctive and other equitable relief, without posting bond or other security, to prevent any material
breach of this Agreement. We may change the terms, conditions and pricing relating to the future licensing of our Systems and other intellectual
property rights, including this Agreement, from time to time. No waiver will be implied from conduct or failure to enforce rights nor effective unless
in a writing signed on behalf of the party against whom the waiver is asserted. If any part of this Agreement is found unenforceable, the remaining
parts will be enforced to the maximum extent permitted. There are no third-party beneficiaries to this Agreement. We are not bound by additional
and/or conflicting provisions in any order, acceptance, or other correspondence unless we expressly agree in writing. This Agreement is the
complete and exclusive statement of agreement between the parties as to its subject matter and supersedes all proposals or prior agreements,
verbal or written, advertising, representations or communications concerning the System. Every reasonable attempt has been made to comply
with all licensing requirements for all components used in the system. Any oversight is unintentional and will be remedied if brought to the
attention of Harmonic at [email protected].
Documentation conventions
In Harmonic documents, special symbols and fonts to call your attention to important information.
DANGER: The Danger symbol indicates information that, if ignored, can cause physical
harm to you.
CAUTION: The Caution symbol indicates information that, if ignored, can adversely affect
the performance of your Harmonic product, or that can make a procedure needlessly
difficult.
NOTE: The Note symbol indicates especially important information you need, or it may
provide additional information that applies in only some carefully delineated circumstances.
IMPORTANT: The Important symbol indicates information that should stand out when you
are reading product details and procedural information.
TIP: The Tip symbol indicates parenthetical information that is not necessary for
performing a given procedure, but which, if followed, makes the procedure easier,
smoother, or more efficient.
In addition to these symbols, this guide may use the following text conventions:
Convention Explanation
Typed Command Indicates the text that you type in at the keyboard prompt.
<Ctrl>, <Ctrl>+<Shift> A key or key sequence to press.
http://www.harmonicinc.com The italics in blue text to indicate Cross-references, and
hyperlinked cross-references in online documents.
Bold Indicates a button to click, or a menu item to select.
Screen Output The text that is displayed on a computer screen.
Emphasis The italics text used for emphasis and document references.
5
Table of Contents
Chapter 1: Introduction to ProView 7100...................................................................................... 6
Packing list.........................................................................................................................................6
Earthing.............................................................................................................................................6
Connecting the power supply to the unit..............................................................................................7
Chapter 2: Installation of ProView 7100........................................................................................ 8
About the installation of the ProView 7100..........................................................................................8
Installing the L-shape slides.................................................................................................................9
Mounting the ProView 7100 units in the 19" rack................................................................................9
Electrical power connection.................................................................................................................9
Connecting the cables........................................................................................................................ 9
Connecting the unit to the electrical power........................................................................................ 10
Appendix A: Harmonic Technical Assistance Center contact information................................ 11
Harmonic corporate contact information............................................................................................12
Appendix B: Safety and regulatory compliance information..................................................... 13
Important safety instructions.............................................................................................................. 13
Safety symbols & translated safety, warning & caution instructions (English)......................................... 14
Symboles de sécurité et traduits de sécurité, d'avertissement et Attention Instructions (français)............... 16
Sicherheit Symbole und übersetzt Sicherheit, Achtung & Vorsicht Anleitung (Deutsch)............................ 20
Site preparation instructions..............................................................................................................24
Product end-of-life disassembly instructions........................................................................................ 25
Safety rules (English)........................................................................................................................ 26
Règles de sécurité.............................................................................................................................26
EU manufacturer’s Declaration of Conformity.....................................................................................26
Electromagnetic compatibility notices – Class A..................................................................................26
Product regulatory compliance markings............................................................................................29
Product environmental compliance.....................................................................................................31
EU RoHS................................................................................................................................... 31
EU REACH.................................................................................................................................32
China RoHS...............................................................................................................................32
Other RoHS and REACH type regulations....................................................................................33
Waste Electrical and Electronic Equipment (WEEE).......................................................................33
Battery directive......................................................................................................................... 34
WEEE Take-Back Request Program..............................................................................................34
Compliance with additional country specific environmental, safety and EMC standards:........................ 35
6
Chapter 1
Introduction to ProView 7100
•Packing list
•Earthing
•Connecting the power supply to the unit
Packing list
Before installation, ensure that all the equipment and the attached parts are available and undamaged,
according to the following list:
Item Quantity
ProView 7100 1
Power cable 1
CAUTION: If anything is missing or damaged, do not continue with the installation and
report to your Harmonic support representative.
Earthing
The guidelines for earthing the unit should be followed.
• The unit must be connected to earth before any other cables are connected.
• The unit should remain permanently connected to protected earth.
• Cable 18AWG should be used.
• When the unit is rack-mounted, the unit's earth stud must be connected to the rack housing, which
must be correctly grounded.
• When removing cables, the earth connection must be removed last.
Introduction to ProView 7100
7 ProView 4.x.x Installation Guide
Connecting the power supply to the unit
The power supply pre-connection warnings.
DANGER: To avoid electrocution, ensure that the rack has been correctly grounded before
connecting the ProView 7100 unit to the main power supply. When removing the unit,
remove the grounded connection only after the unit is unplugged from the main power
supply.
• Ensure that a qualified electrician has installed the main power supply in accordance with power
authority regulations.
• Make sure all powering is wired with an earth leakage, according to local regulations.
• When the unit is rack-mounted, ensure that the rack is correctly grounded.
8
Chapter 2
Installation of ProView 7100
•About the installation of the ProView 7100
•Installing the L-shape slides
•Mounting the ProView 7100 units in the 19" rack
•Electrical power connection
•Connecting the cables
•Connecting the unit to the electrical power
About the installation of the ProView 7100
For rack installation, ensure that a designated 19" rack is fully prepared for installation.
The ProView 7100 comes with ears fitted to each side of the chassis. See the figure for the location of the
ears.
There must be sufficient space behind the rack for easy access for installation and maintenance. Rack
mounting requires the use of L-shape slides, not included, but available from Harmonic. The amount
of units installed in a rack is a function of the units’ power consumption and heat dissipation. Address
Harmonic support for calculating the maximum load on the rack.
Installation of ProView 7100
9 ProView 4.x.x Installation Guide
Installing the L-shape slides
The ProView 7100 uses forced air ventilation, evacuating the air out the left side of the 19" rack. To
ensure smooth airflow, L-shape slides are provided for rack mounting.
Before you begin
Use 4x M6 16mm long screws (not included)
• Fit one L-shape slide to each side of the 19” rack and fasten each with two screws (M6 16mm long).
Mounting the ProView 7100 units in the 19" rack
The ProView 7100 19" rack mounting instructions and warnings.
Before you begin
Use 4x M6 16mm long screws (not included)
1. Mount ProView 7100 units in groups of no more than five units on each pair of L-shape slides.
2. Leave one-unit-space between each group of five units.
3. Mount the ears to the rack, using M6 16mm long screws.
Electrical power connection
The ProView 7100 is powered by an AC power supply.
Connecting the cables
All ProView 7100 connectors are located on the rear panel.
• Connect the input cable(s) to the RF IN or ASI IN port(s).
• Connect the management LAN cable to the Management port.
ProView™
10
• Connect an output destination to one of the output connectors on the output interface.
• Connect a video monitor, for local monitoring of the output, to the CV MON or the HDMI port.
Connecting the unit to the electrical power
Before connecting the power cable of the ProView 7100 to the main power supply, make sure that all
other cables are correctly connected.
• Ensure that the unit is correctly grounded.
• Connect the power cable to the main power supply.
Once the boot process is completed (after 2-3 minutes), the Harmonic Idle message displays on the front
panel LCD.
11
Appendix A
Harmonic Technical Assistance Center contact information
A list of phone numbers, e-mail addresses, and important links for the Harmonic Technical Assistance
Center (TAC).
Table A-1: Technical Assistance Center phone numbers and email addresses
Region Telephone Technical
Support
Email
Americas 888.673.4896
(888.MPEG.TWO)408.490.6477
Europe, the Middle East
and Africa (EMEA)
+44.1252.555.450 [email protected]
India +91.120.498.3199 [email protected]
Russia +7.495.926.4608 [email protected]
China +86.10.6569.5580 [email protected]
Japan +81.3.5565.6737 [email protected]
Asia Pacific (APAC) –
Other Territories
+852.3184.0045
+65.6542.0050
Report an issue online
http://www.harmonicinc.com/webform/report-issue-online
Harmonic support website
http://www.harmonicinc.com/content/technical-support
Software download location for Cable Edge products
ftp://ftp.harmonicinc.com
Contact Harmonic Technical Publications
•Harmonic corporate contact information
ProView™
12
Harmonic corporate contact information
Phone numbers and addresses for the corporate office.
Harmonic corporate address
4300 North First Street
San Jose, CA 95134
U.S.A.
Harmonic corporate telephone numbers
Tel. 1.800.788.1330 (from the U.S. and Canada)
Tel. +1.408.542.2500 (outside the U.S. and Canada)
Fax.+1.408.542.2511
13
Appendix B
Safety and regulatory compliance information
Legal disclaimer: Information in this document is provided in connection with Harmonic products. Unless
otherwise agreed in writing Harmonic products are not designed nor intended for any application in which
the failure of the product could cause personal injury or death.
NOTE: The information in this appendix may apply to purchased products only.
•Important safety instructions
•Safety symbols & translated safety, warning & caution instructions (English)
•Symboles de sécurité et traduits de sécurité, d'avertissement et Attention Instructions (français)
•Sicherheit Symbole und übersetzt Sicherheit, Achtung & Vorsicht Anleitung (Deutsch)
•Site preparation instructions
•Product end-of-life disassembly instructions
•Safety rules (English)
•Règles de sécurité
•EU manufacturer’s Declaration of Conformity
•Electromagnetic compatibility notices – Class A
•Product regulatory compliance markings
•Product environmental compliance
•Compliance with additional country specific environmental, safety and EMC standards:
Important safety instructions
Review important safety guidelines for operators and service personnel.
Specific warnings and cautions are found throughout the guide where they apply, but may not appear
here. Please read and follow the important safety information, noting especially those instructions related
to risk of fire, electric shock or injury to persons. You must adhere to the guidelines in this document to
ensure and maintain compliance with existing product certifications and approvals. In this document, we
use “product,” “equipment,” and “unit” interchangeably.
This equipment generates, uses, and can radiate radio frequency energy. It may cause harmful
interference to radio communications if it is not installed and used in accordance with the instructions in
this manual. Operation of this equipment in a residential area is likely to cause harmful interference If this
occurs, the user will be required to correct the interference at his or her own expense.
In event of conflict between the information in this document and information provided with the product or
on our website for a particular product, this product documentation takes precedence.
ProView™
14
•Safety symbols (English)
•Symboles de sécurité (français)
•Sicherheit symbole (Deutsch)
Safety symbols & translated safety, warning & caution instructions
(English)
Understand the meaning of different safety symbols.
To avoid personal injury or property damage, before you begin installing or replacing the product, read,
observe, and adhere to all the following safety instructions and information. Harmonic products and/or
product packaging may be marked with the safety symbols used throughout this document, when it is
necessary to alert operators, users, and service providers to pertinent safety instructions in the manuals.
Mark Notes
Warning
Installing or replacing the product unit warning
• Only trained and qualified service personnel should be allowed to install,
replace, or service this unit (refer AS/NZS 3260 Clause 1.2.14.3 Service
Personnel).
• Read the installation instructions before connecting the system to the power
source.
• When installing or replacing the unit, always make the ground connection
first and disconnect it last.
• Installation of the unit must comply with local and national electrical codes.
• This unit is intended for installation in restricted access areas. A restricted
access area can be accessed only through the use of special tool, lock and
key or other means of security.
• Use only specified replacement parts.
• Do not use this unit in or near water. Disconnect all AC power before
installing any options or servicing the unit unless instructed to do so by this
manual.
Warning
Rack mount warning
To prevent bodily injury when mounting or servicing this unit in a rack, special
precautions must be taken to ensure your safety and stability of system:
• Conform to local occupational health and safety requirements when moving
and lifting the equipment.
• Ensure that mounting of the unit by mechanical loading tools should not
induce hazardous conditions.
• To avoid risk of potential electric shock, a proper safety ground must be
implemented for the rack and each piece of equipment installed on it.
Safety and regulatory compliance information
15 ProView 4.x.x Installation Guide
Mark Notes
Warning
Chassis warning
• Before connecting or disconnecting ground or power wires to the chassis,
ensure that power is removed from the DC circuit.
• To prevent personal injury or damage to the chassis, lift the unit only by
using handles that are an integral part of the chassis, or by holding the
chassis underneath its lower edge.
• Any instructions in this guide that require opening the chassis or removing a
board should be performed by qualified service personnel only.
• Slots and openings in the chassis are provided for ventilation. Do not block
them. Leave the back of the frame clear for air exhaust cooling and to
allow room for cabling - a minimum of 6 inches (15.24 cm) of clearance is
recommended.
Warning
Electric shock warning
• This unit might have more than one power cord. To reduce the risk of
electric shock, disconnect the two power supply cords before servicing the
unit.
• Before working on a chassis or working near power supplies, unplug the
power cord on AC units.
• Do not work on the system or connect or disconnect cables during periods of
lightning activity.
• This unit is grounded through the power cord grounding conductor. To avoid
electric shock, plug the power cord into a properly wired receptacle before
connecting the product input or outputs.
• Route power cords and other cables so that they are not likely to be
damaged. Disconnect power input to unit before cleaning. Do not use liquid
or aerosol cleaners; use only a damp cloth to clean chassis.
• Dangerous voltages exist at several points in this product. To avoid personal
injury, do not touch exposed connections and components while power
is on. Do not insert anything into either of the system's two power supply
cavities with power connected
• Never install an AC power module and a DC power module in the same
chassis.
• Do not wear hand jewelry or watch when troubleshooting high current
circuits, such as the power supplies.
• To avoid fire hazard, use only the specified correct type voltage and current
ratings as referenced in the appropriate parts list for this unit. Always refer
fuse replacement to qualified service personnel.
• This unit relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that a fuse or circuit breaker no larger than 120 VAC,
15A U.S. (240 VAC, 10A international) is used on the phase conductors (all
current-carrying conductors).
• To avoid electrocution ensure that the rack has been correctly grounded
before switching on the unit. When removing the unit remove the grounding
connection only after the unit is switched off and unplugged.
ProView™
16
Mark Notes
Caution
Electrostatic Discharge (ESD) caution
• Follow static precaution at all times when handling this unit.
• Always wear an ESD-preventive wrist or ankle strap when handling
electronic components. Connect one end of the strap to an ESD jack or an
unpainted metal component on the system
• Handle cards by the faceplates and edges only; avoid touching the printed
circuit board and connector pins.
• Place any removed component on an antistatic surface or in a static
shielding bag.
• Avoid contact between the cards and clothing.
• Periodically check the resistance value of the antistatic strap.
Recommended value is between 1 and 10 mega-ohms (Mohms).
Warning
Laser radiation warning
Invisible laser radiation may be emitted from disconnected fibers or connectors.
Do not stare into beams or view directly with optical instruments. Never operate
a unit with a broken fibre or with a separated fiber connector.
Warning
Lithium battery handling safety instructions
• CALIFORNIA PERCHLORATE ADVISORY: Some lithium batteries may
contain perchlorate material. The following advisory is provided: "Perchlorate
Material - special handling may apply, see: http://www.dtsc.ca.gov/
hazardouswaste/perchlorate/ for information."
Caution
• Risk of explosion if battery is replaced incorrectly or with an incorrect type
• Dispose of used batteries according to the manufacturer's instructions
• There are no user-serviceable batteries inside Harmonic products. Refer to
Harmonic qualified personnel only to service the replaceable batteries
Symboles de sécurité et traduits de sécurité, d'avertissement et
Attention Instructions (français)
Comprendre la signification des différents symboles de sécurité .
Pour éviter des blessures ou des dommages matériels, avant de commencer l'installation ou le
remplacement du produit, lire, observer, et de respecter toutes les instructions et informations de sécurité
suivantes. Produits harmoniques et / ou l'emballage du produit peuvent être marqués avec les symboles
Safety and regulatory compliance information
17 ProView 4.x.x Installation Guide
de sécurité utilisés dans le présent document, lorsque cela est nécessaire pour alerter les opérateurs, les
utilisateurs et les fournisseurs de services de consignes de sécurité pertinentes dans les manuels.
Mark Notes
Avertissement
Installation ou remplacement de l'unité de produit avertissement
• Il est vivement recommandé de confier l'installation, le remplacement
et la maintenance de ces équipements à des personnels qualifiés et
expérimentés. (voir AS / NZS 3260 article 1.2.14.3 du personnel de service).
• Avant de brancher le système sur la source d'alimentation, consulter les
directives d'installation.
• Lors de l'installation ou le remplacement de l'appareil, la mise à la terre doit
toujours être connectée en premier et déconnectée en dernier.
• L'équipement doit être installé conformément aux normes électriques
nationales et locales.
• Cet appareil est à installer dans des zones d'accès réservé. Ces dernières
sont des zones auxquelles seul le personnel de service peut accéder en
utilisant un outil spécial, un mécanisme de verrouillage et une clé, ou tout
autre moyen de sécurité.
• Utilisez uniquement des pièces de rechange spécifiées.
• Ne pas utiliser ce produit dans l'eau ni à proximité de l'eau. Débrancher
toutes les prises d'alimentation secteur avant d'installer des options ou
d'effectuer l'entretien de l'unité, à moins d'instructions contraires dans le
présent manuel.
Avertissement
Rack monture avertissement
Pour éviter les blessures corporelles lors du montage ou l'entretien de cet
appareil dans un rack, des précautions particulières doivent être prises pour
assurer votre sécurité et la stabilité du système:
• Conformez-vous aux exigences de médecine du travail et de sécurité
lorsque vous déplacez et soulevez le matériel.
• Assurez-vous que le montage de l'appareil par des outils de chargement
mécaniques ne doit pas induire des conditions dangereuses.
• Pour éviter tout risque d'électrocution, le rack et chaque élément de
l'équipement installé dans le rack doivent être correctement reliés à la terre.
Avertissement
Châssis avertissement
• Avant de connecter ou de déconnecter les câbles d'alimentation (pôles et
terre) du châssis, vérifiez que le circuit de courant continu est hors tension.
• Pour éviter toute blessure ou des dommages au châssis, soulevez l'unité
uniquement par les poignées du châssis lui-même ou en portant celui-ci par
le bord inférieur.
• Toutes les opérations du présent guide nécessitant l'ouverture du châssis
ou le retrait d'une carte doivent être uniquement effectuées par du personnel
d'entretien qualifié.
• Le châssis est muni de fentes et d'ouvertures d'aération. Ne pas les bloquer.
Dégager l'arrière du cadre pour permettre le refroidissement de l'évacuation
d'air et laisser de la place au câblage; un dégagement d'au moins 15.24 cm
(6 po) est recommandé.
ProView™
18
Mark Notes
Avertissement
Choc électrique avertissement
• Il est possible que cette unité soit munie de plusieurs cordons d'alimentation.
Pour éviter les risques d'électrocution, débrancher les deux cordons
d'alimentation avant de réparer l'unité.
• Avant de travailler sur un châssis ou à proximité d'une alimentation
électrique, débrancher le cordon d'alimentation des unités en courant
alternatif.
• Ne pas travailler sur le système ni brancher ou débrancher les câbles
pendant un orage.
• Ce unité est mis à la terre par le conducteur de protection intégré au
cordon d'alimentation. Pour éviter les chocs électriques, brancher le cordon
d'alimentation dans une prise correctement cable avant de raccorder les
entrées ou sorties du unité.
• Installer les cordons d'alimentation et autres cables de sorte qu'ils ne
risquent pas d'être endommagés. Couper l'alimentation avant nettoyage. Ne
pas utilizer de nettoyant liquide ou en aérosol; utiliser seulement un linge
humide.
• Des courants électriques dangereux circulent dans cet appareil. Afin d'éviter
les lessures, ne pas toucher les connexions et composants exposés lorsque
l'appareil est sous tension. Ne rien insérer dans l'une ou l'autre des cavités
des prises de courant du système lorsque l'appareil est sous tension.
• N'installez jamais un module d'alimentation AC et un module d'alimentation
DC dans le même châssis.
• Ne pas porter de bijoux aux mains ni de montre durant le dépannage des
circuits à haute tension, comme les transformateurs.
• Pour prévenir les risques d'incendie, n'utiliser que le type, la tension et le
courant nominal spécifiés dans la nomenclature des pièces de ce unité.
Toujours confier le remplacement des fusibles à du personnel d'entretien
qualifié.
• Pour ce qui est de la protection contre les courts-circuits (surtension), ce
produit dépend de l'installation électrique du local. Vérifier qu'un fusible
ou qu'un disjoncteur de 120 V alt., 15 A U.S. maximum (240 V alt., 10 A
international) est utilisé sur les conducteurs de phase (conducteurs de
charge).
• Pour éviter l'électrocution, assurez-vous que le rack a bien été mis à la
terre avant de mettre l'unité en marche. Lors du retrait de l'unité, retirer le
raccordement de terre seulement après avoir mis l'unité à l'arrêt et l'avoir
débranchée.
Safety and regulatory compliance information
19 ProView 4.x.x Installation Guide
Mark Notes
Attention
Les décharges électrostatiques (ESD) attention
• Respecter systématiquement les precautions relatives aux charges
électrostatiques durant la manipulation de cet unité.
• Portez toujours un poignet ou la cheville bracelet antistatique préventive lors
de la manipulation des composants électroniques. Branchez une extrémité
de la sangle à une prise ESD ou d'un composant métallique non peinte sur
le système.
• Manipulez les cartes en les faces avant et les bords seulement; éviter de
toucher la carte de circuit imprimé et les broches du connecteur.
• Placer un composant retiré sur une surface antistatique ou dans un sac de
protection statique.
• Éviter tout contact entre les cartes et les vêtements.
• Vérifier périodiquement la valeur de résistance de la sangle antistatique.
Valeur recommandée est comprise entre 1 et 10 méga-ohms (Mohms).
Avertissement
Rayonnement laser attention
Rayonnement laser invisible peut être émis à partir de fibres ou les connecteurs
débranchés. Ne pas regarder en faisceaux ou regarder directement avec des
instruments optiques. Ne jamais faire fonctionner une unité en cas de bris d'une
fibre ou de séparation d'un connecteur de fibre.
Avertissement
Batterie au lithium manipulation instructions de sécurité
• Perchlorate pour la Californie Consultatif: Certaines batteries au lithium,
peuvent contenir du perchlorate. le texte qui suit consultatif est prévu:
"Présence de perchlorate - une manipulation spéciale peut s'appliquer, voir:
http://www.dtsc.ca.gov/hazardouswaste/perchlorate/ for information."
Attention
• Il y a danger d'explosion si la batterie est remplacée de manière incorrecte
ou par une batterie de type incorrect.
• Mettre au rebut les batteries usagees conformement aux instructions du
fabricant.
• Les batteries des produits Harmonic ne peuvent pas être réparées ni
entretenues par l'utilisateur. Ne confier l'entretien des batteries remplaçables
qu'à du personnel compétent de Harmonic.
ProView™
20
Sicherheit Symbole und übersetzt Sicherheit, Achtung & Vorsicht
Anleitung (Deutsch)
Verstehen Sie die Bedeutung der verschiedenen Sicherheitssymbole .
Um Verletzungen oder Sachschäden zu vermeiden, bevor Sie mit der Installation oder Austausch des
Produkts zu beginnen, zu lesen, zu beobachten, und sich an all den folgenden Sicherheitshinweise und
Informationen. Harmonic Produkte und / oder Produktverpackungen können mit den Sicherheitssymbole
in diesem Dokument verwendet werden, markiert, wenn es notwendig ist für die Betreiber, Anwender und
Dienstleister, um relevante Sicherheitsanweisungen in den Handbüchern zu alarmieren.
Mark Notes
Warnung
Installation oder den Austausch des Produkts Einheit Warnung
• Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur
geschultem, qualifiziertem Personal gestattet warden (siehe AS / NZS 3260
Clause 1.2.14.3 Servicepersonal)
• Lesen Sie die Installationsanweisungen, bevor Sie das System an die
Stromquelle anschließen.
• Der Erdanschluß muß bei der Installation der Einheit immer zuerst
hergestellt und zuletzt abgetrennt werden.
• Die Installation der Geräte muss den Sicherheitsstandards entsprechen.
• Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt
vorgesehen. Ein Bereich mit beschränktem Zutritt ist ein Bereich, zu dem
nur Wartungspersonal mit einem Spezialwerkzeugs, Schloß und Schlüssel
oder anderer Sicherheitsvorkehrungen Zugang.
• Verwenden Sie nur die angegebenen Ersatzteile
• Das Gerät in oder in der Nähe von Wasser verwenden. Trennen Sie vor
der Installation von Optionen oder Wartung des Gerätes, es sei denn, dies
wurde von diesem Handbuch alle Netz.
Warnung
Rack-Montage-Warnung
Zur Vermeidung von Körperverletzung beim Anbringen oder Warten dieser
Einheit in einem Gestell müssen Sie besondere Vorkehrungen treffen, um
sicherzustellen, daß das System stabil bleibt:
• Entsprechen den lokalen Arbeitsschutzanforderungen beim Bewegen und
Heben der Ausrüstung.
• Stellen Sie sicher, dass die Montage des Gerätes durch mechanische
Belastung Werkzeuge sollten nicht gefährlichen Bedingungen zu induzieren.
• Um das Risiko von möglichen elektrischen Schlag zu vermeiden, muss
mit einer angemessenen Erdung für Rack und jedes Gerät installiert ist
implementiert werden.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Harmonic ProView 7100 4.0.3 Guide d'installation
- Taper
- Guide d'installation
dans d''autres langues
Documents connexes
-
Harmonic ProView 7100 4.1 Guide d'installation
-
-
-
-
-
-
-
-
-