Bosch KTS 340 Original Instructions Manual

KTS 340

en

Original instructions

System tester for

control unit diagnosis

fr

Notice originale

Testeur système pour le diagnostic des

centrales de commande

es

Manual original

Comprobador de sistema para

el diagnóstico de unidades de mando

1 689 989 072 2010-06-09| Robert Bosch GmbH

| KTS 340 | 3KTS 340 | 3 | 3

de

Contents English 4

Sommaire Français 20

Índice Español 36

1 689 989 072 2010-06-09| Robert Bosch GmbH

4 | KTS 340 | en

Contents

1. Symbols used 5

1.1 Documentation 5

1.2 KTS 340 5

2. User information 5

2.1 Important notes 5

2.2 Safety instructions 5

2.3 Electromagnetic compatibility (EMC) 5

2.4 Disposal 5

2.5 Open Source Software 5

2.6 J2534 Reprogramming, web browser 5

2.7 WLAN (Wireless Local Area Network) 6

2.7.1 Important information on WLAN 6

2.7.2 Information on access points 6

2.7.3 Information on WLAN for USA and

Canada 6

3. Product description 7

3.1 Use 7

3.2 System requirements 7

3.3 Scope of delivery 7

3.4 Special accessories 7

3.5 Description of the unit 8

3.6 USB adapter 8

3.7 LED status 8

3.7.1 Battery charge LED 8

3.7.2 WLAN LED 8

4. Commissioning 9

4.1 Connection 9

4.2 Licensing with the

ESI[tronic] Startcenter 9

4.2.1 Installing the ESI[tronic] Startcenter 9

4.2.2 Licensing the KTS 340 online 11

4.2.3 Licensing the KTS 340 by fax 13

4.2.4 KTS 340 fax licensing procedure 13

5. Operation 13

5.1 Connection to the vehicle 13

5.2 Switching on 14

5.3 Switching off 14

5.4 Notes on multimeter 14

5.5 Touchscreen with stylus 14

5.6 Program description 14

5.7 Software update 15

5.7.1 Online software update

(from ESI[tronic] Startcenter

version 2010/2) 15

5.7.2 Software update using the

ESI[tronic] DVD 15

5.8 Faults 15

6. Maintenance 16

6.1 Cleaning 16

6.2 Rechargeable battery replacement 16

6.3 Spare and wearing parts 16

7. Technical data 17

7.1 General data 17

7.2 Interface protocols 17

7.3 Power supply unit 17

7.4 Multimeter speciﬁcations 17

7.4.1 DC measurement (CH1 and CH2) 17

7.4.2 Measurement of AC and rms value

(CH1 and CH2)

*)

17

7.4.3 Resistance measurement (CH1) 17

7.4.4 Current measurement (CH1 and CH2) 18

7.4.5 Continuity tester (CH1) 18

7.4.6 Diode measurement (CH1) 18

7.5 WLAN 18

1 689 989 072 2010-06-09| Robert Bosch GmbH

Symbols used | KTS 340 | 5KTS 340 | 5 | 5

en

1. Symbols used

1.1 Documentation

Pictograms linked with the key words Danger, Warning

and Caution are warnings and always indicate an imme-

diate or potential hazard to the user.

Danger!

Immediate danger that could cause serious

personal injury or death.

Warning!

Potentially dangerous situation that could

cause serious personal injury or death.

Caution!

Potentially dangerous situation that could

cause personal injury or damage to property.

! Important – warns of a potentially hazardous situa-

tion in which the KTS 340, the test sample or other

object in the vicinity could be damaged.

In addition to these warnings, the following symbols are

also used:

i Info – Details for the application and further useful

information.

¶ Single-step procedure – instructions for a procedure

that can be completed in just one step.

? Intermediate result – an intermediate result is dis-

played during a procedure.

"Final result – the final result is displayed at the end

of the procedure.

1.2 KTS 340

Disposal

Old electrical and electronic devices, including

cables and accessories or batteries must be

disposed of separate to household waste.

2. User information

2.1 Important notes

Important information on copyright, liability and warranty

provisions, as well as on equipment users and company

obligations, can be found in the separate manual "Important

notes on and safety instructions for Bosch Test Equipment".

These instructions must be carefully studied prior to start-

up, connection and operation of the KTS 340 and must

always be heeded.

2.2 Safety instructions

All the pertinent safety instructions can be found in the

separate manual "Important notes on and safety instruc-

tions for Bosch Test Equipment". These instructions

must be carefully studied prior to start-up, connection

and operation of the KTS 340 and must always be heed-

ed.

2.3 Electromagnetic compatibility (EMC)

The KTS 340 is a class B product as per EN 61 326.

2.4 Disposal

This KTS 340 is subject to European guideli-

nes 2002/96/EG (WEEE).

Old electrical and electronic devices, including-

cables and accessories or batteries must be

disposed of separate to household waste.

¶ Please use the return and collection sys-

tems in place for disposal in your area.

¶ Damage to the environment and hazards to

personal health are prevented by properly

disposing of KTS 340.

2.5 Open Source Software

A list of the open source software licenses for the

KTS 340 can be found in an Adobe PDF document on

the “ESI[tronic] Startcenter” DVD.

Caution – Hot charging contacts

Risk of burns if touched.

¶ Do not touch charging contacts.

2.6 J2534 Reprogramming, web browser

i The " (Info) >> Help" menu in the Online Help

contains all the necessary information on J2534

Reprogramming and the web browser.

1 689 989 072 2010-06-09| Robert Bosch GmbH

6 | KTS 340 | Symbols useden

2.7 WLAN (Wireless Local Area Network)

2.7.1 Important information on WLAN

WLAN stands for Wireless Local Area Network. As

with Bluetooth, WLAN provides a radio link on the free

2.4 GHz ISM band (ISM: Industrial, Scientific, Medical).

This frequency range is subject to government regula-

tions, but may be used without a license in most coun-

tries. Consequently a large number of applications and

devices employ this frequency band for transmission.

This can result in frequency interference.

Depending on ambient conditions, the WLAN link may

therefore deteriorate, e.g. in the case of Bluetooth links,

cordless telephones, radio-controlled thermometers,

radio-controlled garage door openers, radio-controlled

light switches or radio-controlled alarm systems.

i Bluetooth can lead to interference in the bandwidth

of the WLAN network. The antennas of Bluetooth

and WLAN devices should be at least 30 centimeters

apart. Do not plug Bluetooth USB adapters and WLAN

sticks into adjacent USB slots on PCs/laptops. Use

the USB extension cable (special accessory) to main-

tain a distance between the Bluetooth USB adapter

and the WLAN stick on the PC/laptop.

i Exercise extreme caution if wearing pacemakers

or other vital electronic devices when using radio

systems, as proper functioning of these items could

be impaired.

Note the following to ensure the best possible connec-

tivity:

R The WLAN radio signal always tries to find the most

direct path. When setting up the PC/laptop and ac-

cess point (see section 2.6.2), make sure there are

as few obstacles as possible (e.g. steel doors and

concrete walls), which could interfere with the radio

signal from and to the KTS 340. Inside buildings, the

range of the WLAN is also greatly influenced by the

construction materials used. Conventional masonry,

wooden walls and certain types of dry construc-

tion wall scarcely impede radio waves. Thin gypsum

walls can however cause problems, as considerable

amounts of moisture may accumulate in the gypsum

and result in the absorption of radio signals. Concrete

(and in particular reinforced concrete) largely blocks

out radio waves. Cellar ceilings are often impenetra-

ble. Generally speaking, walls with a lot of installed

metal (e.g. pipes, wires) obstruct radio waves.

R Radio reception is also impeded by large metal

objects such as radiators and window frames as

well as active sources of interference such as DECT

telephones and microwave ovens.

R Have your network infrastructure installed and

tested in advance by a data systems expert.

R Keep the SSID and the codes for the radio link in a

safe place. Make sure these data are readily to hand

in case faults occur.

R We recommend a thorough inspection of the pre-

mises on commissioning: Establish where in the

building the KTS 340 works properly and where the

operating limits are.

R If the KTS 340 is to be used in a vehicle (Faraday

cage), radio communication can be severely limited.

R The radio link is affected by weather conditions. The

reception signal may therefore vary.

R Please contact your network administrator with any

queries.

2.7.2 Information on access points

A wireless access point is an electronic device, which

acts as an interface between a radio network and a

cable-connected computer network. It provides a wire-

less connection between the KTS 340, the PC/laptop

with ESI[tronic] Startcenter and a printer, for example.

i We recommend using WLAN standard IEEE 802.11g

(data transmission rate max. 54 Mbps) for the access

point. The "extended range" function is not supported.

Please note the following:

R The access point should be located as centrally and

high up as possible, ideally under the ceiling.

R The access point antenna should face downwards

towards the floor.

R In the event of a poor connection it may be useful to

change the set channel on the access point. If pos-

sible, avoid using neighboring channels to channels

that are already in use.

R We recommend that encryption of radio communica-

tions is configured at the access point.

2.7.3 Information on WLAN for USA and Canada

USA:

Changes or modifications not expressly approved by

the party responsible for compliance could void the

user’s authority to operate the equipment.

Canada:

Operation is subject to the following two conditions:

R this device may not cause interference, and

R this device must accept any interference, including

interference that may cause undesired operation of

the device.

This Class [B] digital apparatus complies with Canadian

ICES-003.

1 689 989 072 2010-06-09| Robert Bosch GmbH

Product description | KTS 340 | 7KTS 340 | 7 | 7 en

3. Product description

3.1 Use

The KTS 340 is a system tester for control unit diag-

nosis, trouble-shooting, repair and service in auto-

motive workshops. The functions of the KTS 340 with

licensed ESI[tronic] are as follows:

R Vehicle identification

R Vehicle information

R Diagnosis

R Service information

R Maintenance

i The KTS 340 is designed for operation in the WLAN

2.4 GHz for USA, Canada and Mexico.

The device satisfies the requirements of the R&TTE

(Radio Equipment and Telecommunications Terminal

Equipment) Directive, as confirmed by the CE mark.

! The KTS 340 is a precision device, which is not to

be subjected to sources of heat (e.g. direct sun-

light), impact, vibration, magnetic fields and exces-

sive soiling. The KTS 340 may only be opened for

changing the battery (the battery referred to in this

manual is a rechargeable battery).

3.2 System requirements

A PC/laptop with WIN XP (SP2), WIN Vista

TM

Home

Premium, WIN Vista

TM

Business or WIN 7 operating

system and at least one free USB port is required for

KTS 340 licensing using the ESI[tronic] Startcenter and

the software update for KTS 340 control unit diagnosis.

The USB port must support the USB 2.0 or USB 1.1

protocol.

3.3 Scope of delivery

Description Order number

KTS 340

Power supply unit

Power supply lead

1 687 022 890

1 684 461 161

USB connecting cable, 3 m 1 684 465 562

OBD diagnostic cable, 3 m 1 684 465 557

UNI connecting cable, 4 core 1 684 463 539

Stylus (3x) 1 683 083 007

USB adapter 1 681 335 117

ESI[tronic] Startcenter DVD 1 987 P12 034

KTS 340 Getting Started DVD 1 687 370 308

Case 1 685 438 626

Measuring lead, red 1 684 430 065

Measuring lead, blue 1 684 430 066

Measuring lead, yellow 1 684 430 067

Ground cable, black 1 684 430 068

Test prod, red (2x) 1 684 485 035

Connection terminal, black 1 684 480 022

Important information and safety instructions 1 689 985 000

KTS 340 operating instructions 1 689 989 072

KTS 340 Quick Start Guide 1 689 989 075

EU Declaration of conformity 1 689 974 307

! Always store the KTS 340 and accessories in the

case when not in use.

3.4 Special accessories

Information on special accessories, such as vehicle-

specific connecting cables, can be obtained from your

authorized Bosch dealer.

1 689 989 072 2010-06-09| Robert Bosch GmbH

8 | KTS 340 | Product descriptionen

3.5 Description of the unit

The KTS 340 is a modular, portable diagnostic system

that can be used anywhere. The KTS 340 features a

computer unit with memory card and an 8.4 inch LCD

touchscreen. ESI[tronic] is pre-installed on the memory

card at the factory.

The operator has a choice of a stylus for the LCD

touchscreen and an on-screen keyboard.

The KTS 340 and accessories are supplied in a protec-

tive case.

KTS 340

Powered b

y ESI tronic

ax. 28 Vm

459843-5K

1

8

7

6

5

4

3

2

Fig. 1: KTS 340

1 Stylus holder

2 Stylus

3 On/Off button

4 Power supply unit connection

5 USB port

6 WLAN LED

7 Battery charge LED

8 LCD touchscreen

! There is a risk of injury from glass splinters should

the LCD glass cover break.

CH2

ax. 60 Vm

DIAG

CH1

K

459843_1Ko

1

7

543

2 6

Fig. 2: Rear view of KTS 340

1 Stylus compartment

2 CH2 measurement input

3 Ground connection

4 CH1(-) measurement input

5 CH1(+) measurement input

6 Diagnostic cable connection (DIAG)

7 Connection for Kensington security lock

3.6 USB adapter

For direct printing via USB, the KTS 340 must be linked to

a Bosch-approved printer via USB connecting cables and

the USB adapter (USB-A/A adapter) (refer to Online Help:

"

(Service) >> User settings >> Print settings").

3.7 LED status

3.7.1 Battery charge LED

Battery charge LED Status

Green light Battery fully charged, external

power supply connected.

Flashing green Battery fully charged, external

power supply not connected.

Yellow light Battery being charged, external

power supply connected.

Flashing yellow Battery almost flat, connect

external power supply.

Red light Fault on charging.

Flashing red Battery flat (KTS 340 will be

switched off within 2 minutes),

connect external power supply.

3.7.2 WLAN LED

WLAN LED Status

Green light WLAN is configured and KTS 340

is connected to an access point,

field strength good.

Yellow light

WLAN is configured and KTS 340

is connected to an access point,

field strength poor.

Red light

WLAN is configured, KTS 340 is

not connected to an access point.

Off WLAN is not configured.

1 689 989 072 2010-06-09| Robert Bosch GmbH

Commissioning | KTS 340 | 9KTS 340 | 9 | 9 en

4. Commissioning

4.1 Connection

Prior to commissioning, make sure the mains voltage

matches the voltage specified on the power supply unit

(use the power supply lead provided).

4.2 Licensing with the

ESI[tronic] Startcenter

The KTS 340 is supplied pre-installed and pre-licensed

and can be used immediately for control unit diagnosis.

The KTS 340 has to be re-licensed to be able to utilize

the functions detailed in the purchase contract and to

implement further updates. The customer number and

password required for this can be found on the delivery

note.

! Do not connect the KTS 340 to the PC/laptop until

prompted to do so during the installation routine.

4.2.1 Installing the ESI[tronic] Startcenter

Procedure:

1. Close all open applications.

2. Insert the "ESI[tronic] Startcenter" DVD.

3. Open the "Windows Explorer".

4.

Start D:\setup.exe (D = DVD drive).

? Setup commences.

? The following message appears with WIN Vista:

An unidentified program is attempting

to access the computer.

? The following message appears with WIN 7:

Do you wish to allow changes to be

made to this computer by the fol-

lowing program?

5. Confirm the message with "Allow" or "Yes".

6. Select the installation language and confirm with <OK>.

i The selected installation language will also be the

language used in the ESI[tronic] Startcenter.

7. Follow the on-screen instructions.

i Select the country in which the KTS 340 is to be

used in the "Country selection" installation menu.

The dialog box does not appear if a country was

already selected during an earlier installation of

Startcenter (e.g. with KTS 200).

i If Adobe Reader is not yet installed on the PC/laptop,

it will be installed at the end of the ESI[tronic] Start-

center installation routine. Adobe Reader is required

to display the KTS 340 control unit diagnosis logs on

the PC/laptop.

i We recommend that you only install the KTS data

packet on the hard disk if you wish to update several

KTS units. Then, the ESI[tronic] Startcenter DVD will

not be required for update.

? The following message appears with WIN Vista:

Do you wish to install this device

software?

8. Confirm the message with "Install".

1 689 989 072 2010-06-09| Robert Bosch GmbH

10 | KTS 340 | Commissioning en

9. Disconnect the USB link to the KTS 340.

? The following message then appears with WIN 7:

Windows can't verify the publisher of

this driver software

.

10. Confirm the message with "Install this driver soft-

ware anyway".

11. Switch on the KTS 340.

i The KTS 340 always starts up in English (US) when

first switched on. The language can be changed

under "

(Service) >> User setting >> Language

setting".

i The ESI[tronic] Startcenter installation routine au-

tomatically installs the USB driver to permit commu-

nication between the KTS 340 and the PC/laptop.

The "Connect USB" dialog box does not appear if the

USB driver was already installed during an earlier

installation of Startcenter (e.g. with KTS 200).

? The following message appears with WIN XP:

This wizard helps you install soft-

ware for: KTS-embedded.

? The following message appears with WIN Vista:

Windows needs to install driver

software for your KTS embedded.

12. Close the message with "Cancel".

? The following message then appears with WIN

Vista and WIN 7:

Windows can't verify

the publisher of this driver soft-

ware.

13. Confirm the message with "Install this driver soft-

ware anyway".

14. To successfully conclude installation, restart the

PC/laptop.

? ESI[tronic] Startcenter has been installed.

1 689 989 072 2010-06-09| Robert Bosch GmbH

Commissioning | KTS 340 | 11KTS 340 | 11 | 11 en

15. Start the "ESI[tronic] Startcenter".

i The " (Info) >> Help" menu opens the online

help. This contains all essential information on the

ESI[tronic] Startcenter.

16. Perform KTS 340 licensing by fax or online.

4.2.2 Licensing the KTS 340 online

! A PC/laptop with Internet access is required for

online licensing.

1. Connect the KTS 340 to the mains voltage via the

supplied power supply unit, and switch on.

? The KTS 340 starts up.

2.

Connect the KTS 340 to a PC/laptop by means of the

USB connecting cable.

3. Select the "Licensing >> Online" menu in the Start-

center.

? The "Online licensing" input box opens.

4. Step 1: Enter the customer number/password and

select <Login>.

? The Internet connection for online licensing is

established.

i If "Login" is not possible, check proxy settings under

"

(Service) >> User settings".

1 689 989 072 2010-06-09| Robert Bosch GmbH

12 | KTS 340 | Commissioning en

5. Step 2: Select the contract ID, then <Generate>.

? The license key is requested.

i The request for the license key can take several

seconds.

! While the license key is being transferred, the USB

link and the power supply to the KTS 340 must not

be interrupted.

6. Select <Execute>.

? The license key is transferred to the KTS 340.

? If licensing is successful, the KTS 340 is restarted.

"The KTS 340 is now licensed and ready for operation.

1 689 989 072 2010-06-09| Robert Bosch GmbH

Commissioning | KTS 340 | 13KTS 340 | 13 | 13 en

4.2.3 Licensing the KTS 340 by fax

1. Select the "Licensing >> Fax" menu in the Start-

center.

? The "License request" input box is opened.

2. Step 1: Enter company data.

3. Step 2: Select country for license request.

4. Step 3: Enter ID number and print out licensing

form.

5. Sign licensing form and submit by fax.

4.2.4 KTS 340 fax licensing procedure

Once you have received the license key by fax, you need

to perform the actual licensing.

1. Connect the KTS 340 to the mains voltage via the

supplied power supply unit, and switch on.

? The KTS 340 starts up.

2.

Connect the KTS 340 to a PC/laptop by means of the

USB connecting cable.

3. Click the "Licensing >> Licensing procedure" menu

in the Startcenter.

? The "License request" input box opens.

4. Enter the customer number, ID number and license

key.

5. Perform licensing.

? The license key is transferred.

? If licensing is successful, the KTS 340 is restarted.

"The KTS 340 is now licensed and can be used for control

unit diagnosis.

5. Operation

5.1 Connection to the vehicle

The KTS 340 is designed for operation on vehicles with

a battery voltage of 12 V and 24 V.

! Make sure the OBD diagnostic cable is properly con-

nected to the KTS 340 and firmly attached. Incorrect

connection could cause the pins of the connector

to bend or break off. Only use the OBD diagnostic

cable contained in the scope of delivery.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

1

3

2

7

6

CH2

ax. 60 V

m

DIAG

K

CH1

KTS 34

0

Powered by ESI tr

onic

459843

8

5

4

Fig. 3: KTS 340 connection diagram

1 OBD diagnostic socket in vehicle

2 OBD diagnostic cable

3 UNI connecting cable

4 USB connecting cable

5 Connecting cable for cigarette lighter socket (special accessory)

6 Power supply unit

7 KTS 340

8 Measuring leads

Placing the KTS 340 on the steering wheel

will lead to a risk of injury due to triggering

of the airbag.

1 689 989 072 2010-06-09| Robert Bosch GmbH

14 | KTS 340 | Operationen

The KTS 340 is connected to the diagnostic interface in

the vehicle by means of:

R The OBD diagnostic cable (Fig. 3, Pos. 2), or

R The OBD diagnostic cable and also the UNI connect-

ing cable (Fig. 3, Pos. 3; special accessory), or

R The OBD diagnostic cable and also a vehicle-specific

adapter cable (special accessory), or

R A vehicle-specific adapter cable

(special accessory).

5.2 Switching on

¶ Switch on the KTS 340 with the On/Off button.

"After the system has started, the KTS 340 remains

in the "Vehicle identification" start screen. The start

screen is always displayed after switch-on.

! If the KTS 340 is supplied with power via the power

supply unit, always use the power supply unit

provided. Do not use power supply units with less

power than 15V/3A, such as those supplied with the

KTS 200 or KTS 5xx, for example.

The KTS 340 is usually supplied with power via the

OBD diagnostic socket in the vehicle. If you do not

know where in the vehicle the OBD diagnostic socket is

located, we recommend finding it by means of KTS 340

control unit diagnosis.

i In some vehicles, the cigarette lighter socket only

supplies power when the ignition is turned on.

i If a test step involves starting the engine, the battery

voltage may drop to such an extent that supply via

the vehicle is no longer guaranteed. In such cases

it may be necessary to supply the KTS 340 via the

power supply unit.

i In some vehicles, the ignition must be switched on in

order for power to be supplied via the OBD interface.

If the KTS 340 is connected to a PC/laptop via the USB

connecting cable, we recommend supplying it with

power via the power supply unit provided.

5.3 Switching off

¶ Press the On/Off button for approx. three seconds.

"The KTS 340 is switched off.

If it is only being run off the battery, the KTS 340 is

switched off if the battery voltage drops below 8 V or if

the device has not been used for ten minutes (factory

setting).

If the KTS 340 is being supplied via an external power

source (e.g. OBD diagnostic cable or power supply

unit) and is not used for a lengthy period, the bright-

ness of the LCD touchscreen is reduced.

5.4 Notes on multimeter

Danger from high voltage!

There is a risk of potentially fatal voltage if

measurements are taken without a ground

cable.

¶ If no diagnostic cable is connected, use the

ground cable provided to make a ground

connection between the KTS 340 and ve-

hicle ground before taking U, R or I measu-

rements.

¶ Connect the ground cable as close as pos-

sible to the object to be measured.

¶ Only use the KTS 340 on the vehicle and not

for measurements involving voltages > 60 V.

¶ Do not perform any measurements on igni-

tion systems.

¶ Only use the test cables provided (with

contact protection).

¶ Always plug in the test cables at the

KTS 340 first and then on the vehicle.

¶ Do not lay unshielded test cables close

to sources of major interference such as

ignition cables.

5.5 Touchscreen with stylus

The touchscreen of the KTS 340 is operated with the

stylus. Touch the application you require with the

stylus.

i You can perform "Touchscreen calibration" in the

Service menu

via "User settings >> Customer

Service". To avoid errors, your eyes must be vertical-

ly above the calibration points. Click on the calibra-

tion points as accurately as possible.

5.6 Program description

You can open the online help for the KTS 340 in the

header bar under

.

You can find basic information on the KTS 340 and

the ESI[tronic] Startcenter in the "ESI[tronic] trainer".

1 689 989 072 2010-06-09| Robert Bosch GmbH

Operation | KTS 340 | 15KTS 340 | 15 | 15 en

5.7 Software update

The software update is performed either using the

"ESI[tronic] Startcenter" DVD or "Online".

! Only perform the software update for a licensed

KTS 340. The USB link and the power supply to the

KTS 340 must not be interrupted during the software

update. In addition, Standby mode on the PC/laptop

must be deactivated.

i The ESI[tronic] Startcenter DVD 1 (annual basic ver-

sion) must be installed using the "Software update

by way of DVD" function.

i You can find the online help for the software update

in the ESI[tronic] Startcenter under "Help >> Help".

i If the software update of the KTS 340 was aborted

(e.g. USB link was interrupted) or installation was

incomplete, you can perform a recovery in the

ESI[tronic] Startcenter under "Help >> Customer

Service" in the menu "

Restore KTS software" (see

ESI[tronic] Startcenter online help).

5.7.1 Online software update (from ESI[tronic]

Startcenter version 2010/2)

1. Start the "ESI[tronic] Startcenter".

2. Open the "Settings >>Online updates" input box.

3. Enter the customer number and password and select

<Next>.

i If "Login" is not possible, check proxy settings under

"Settings >> User settings".

4. Select an available update and start the software

update.

5. Follow the on-screen instructions.

i To successfully conclude installation, restart the

PC/laptop.

KTS 340 software update

1. Disconnect the power supply unit and USB connect-

ing cable from the KTS 340.

2. Start the "ESI[tronic] Startcenter".

3.

Supply power to the KTS 340 once more with the

power supply unit.

? The KTS 340 starts up.

? The start screen "Vehicle identiﬁcation" appears.

4.

Connect the KTS 340 to a PC/laptop by means of the

USB connecting cable.

5. ESI[tronic] Startcenter: Open "

KTS 340 >> Device

information".

6. Select an available update

7. Select <Update>.

"The system software is installed on the KTS 340.

5.7.2 Software update using the ESI[tronic] DVD

Step 1: Installing ESI[tronic] Startcenter

1. Close all open applications.

2. Insert the "ESI[tronic] Startcenter" DVD.

3. Open the "Windows Explorer".

4.

Start D:\setup.exe (D = DVD drive).

? Setup commences.

5. Follow the on-screen instructions (see section 4.2.1).

i To successfully conclude installation, restart the

PC/laptop.

Step 2: KTS 340 software update

1. Disconnect the power supply unit and USB connect-

ing cable from the KTS 340.

2. Start the "ESI[tronic] Startcenter".

3.

Supply power to the KTS 340 once more with the

power supply unit.

? The KTS 340 starts up.

? The "Vehicle identiﬁcation" dialog box appears.

4.

Connect the KTS 340 to a PC/laptop by means of the

USB connecting cable.

5. ESI[tronic] Startcenter: Open "

KTS 340 >> Device

information".

6. Select an available update

i If no "available update" is displayed, the KTS 340

already has the current software and does not need

to be updated.

7. Select <Update>.

"The system software is installed on the KTS 340.

5.8 Faults

No communication with the control unit

The fault message "No system found" appears during

control unit diagnosis.

Possible causes Action to be taken

Incorrect cable

connected.

Check that the correct cable has been

used.

Wrong pin selected in

pin selection menu.

Check which pin must be used in "Diag-

nostic socket".

i If problems of a different nature occur, please con-

tact the ESI[tronic] Service Hotline directly.

1 689 989 072 2010-06-09| Robert Bosch GmbH

16 | KTS 340 | Maintenanceen

6. Maintenance

6.1 Cleaning

Only clean the housing and display of the KTS 340 with

a soft cloth and neutral cleaning agents. Do not use

abrasive cleaning agents or coarse workshop cloths.

6.2 Rechargeable battery replacement

Danger due to high voltage!

If the KTS 340 is open and the cover (Fig. 4,

Pos. 5) of the LCD background illumination

has been removed, life-threatening high volt-

age may occur.

¶ Never remove the cover of the background

illumination.

Incorrect handling carries a risk of ignition,

bursting or combustion!

Batteries must not be heated, burned, short-

circuited, mechanically damaged or charged

with excessively high currents or reverse

polarity.

¶ Suitable extinguishing agents: Water,

CO

2

, sand.

! Only use the nickel-metal hydride batteries specified

for the KTS 340. We recommend batteries with a

battery capacity of 2000 mAh to 2300 mAh. Always

replace all the batteries. Dispose of old batteries in

accordance with the applicable legislation.

1. Switch off the KTS 340.

2. Slacken the screws (5x, Fig. 4, Pos. 1) on the back

of the unit and detach the housing cover (Fig. 4,

Pos. 2).

3. Take out the battery compartments on the left and

right and set down on the metal housing (Fig. 4,

Pos. 3).

4. Take out the old batteries (Fig. 4, Pos. 4).

5. Insert new batteries (8x), taking care to ensure

correct polarity.

6. Re-insert the battery compartments in the unit.

! Take care not to trap the leads to the battery com-

partment when fitting the back panel.

7. Re-fit the back panel of the unit.

8. Screw the screws (5x) back in.

Best.-Nr.: 1 687 023 436

Best.-Nr.: 0 684 400 340

Typ: KTS 340

Serien-:Nr

.

FD: 2008-04 U(V);8

-28 DC

P(W): 20

PMade in Germany Robert Bosch GmbH D-73207 Plochingen

F(Hz):

430003520

FD; 2008-04

BOSCH

BOS

CH

ax. 28 Vm

459843-3Ko

1

4

3

2

3

4

5

Fig. 4: Rechargeable battery replacement

6.3 Spare and wearing parts

Description Order number

System tester KTS 340 (green) 1 687 023 549

Power supply unit

Power supply lead

1 687 022 890

1 684 461 161

USB connecting cable, 3 m 1 684 465 562

OBD diagnostic cable, 3 m

<)

1 684 465 557

4-pole UNI connecting cable

<)

1 684 463 539

Stylus (3x) 1 683 083 007

USB adapter 1 681 335 117

Case 1 685 438 626

Measuring lead, red

<)

1 684 430 065

Measuring lead, blue

<)

1 684 430 066

Measuring lead, yellow

<)

1 684 430 067

Ground cable, black

<)

1 684 430 068

Test prod, red (2x)

<)

1 684 485 035

Connection terminal, black

<)

1 684 480 022

Adapter insert 1 688 000 355

Batteries (8x) 1 687 335 031

<)

Wearing part

1 689 989 072 2010-06-09| Robert Bosch GmbH

Technical data | KTS 340 | 17KTS 340 | 17 | 17 en

7. Technical data

7.1 General data

Property Value/Range

Operating voltage 11 VDC — 34 VDC

Power consumption approx. 50 W

LCD 8.4"

800 x 600 pixels

Dimensions (L x W x H)

235 x 290 x 67 mm

9.25 x 11.42 x 2.64 inch

Weight (without connecting cables) 2100 g

4.6 lb

Operating temperature 5 °C – 40 °C

41 °F – 104 °F

Relative humidity 90 % (at 25 °C)

Degree of protection IP 40

7.2 Interface protocols

The following interfaces and their associated protocols

are supported for control unit diagnosis in compliance

with ISO 15031:

R ISO/DIS 15765-4 (CAN) - baud rates: 250 kbit/s and

500 kbit/s)

R ISO 9141-2 Fast

R ISO/DIS 14230-4 (keyword protocol 2000) 5 bauds

R ISO/DIS 14230-4 (keyword protocol 2000) Fast

R ISO/DIS 11519-4 (SAE J1850) PWM

R ISO/DIS 11519-4 (SAE J1850) VPW

7.3 Power supply unit

Property Value/Range

Input voltage 100 VAC — 240 VAC

Input frequency 50 Hz — 60 Hz

Output voltage 15 V

Operating temperature 0 °C — 40 °C

7.4 Multimeter specifications

R CH1 zero potential (blue input may be connected to

live measurement points). Input resistance

> 900 kohms.

R CH2 non-floating (black ground input must be

connected to vehicle ground). Input resistance

> 900 kohms.

7.4.1 DC measurement (CH1 and CH2)

Property Value/Range

Measuring range 200 mV — 60 V

Accuracy of CH1 ±0.75 % of measured value,

plus ±0.25 % of measuring range

Accuracy of CH2 ±2 % of measured value,

plus ±0.5 % of measuring range

Resolution 100 µV — 100 mV

(depending on measuring range)

7.4.2 Measurement of AC and rms value

(CH1 and CH2)

*)

Property Value/Range

AC frequency range 10 Hz — 400 Hz (-3 dB)

Measuring range 200 mV — 60 V

AC accuracy at 100 Hz

rms accuracy at ≤ 100 H

±2 % of measured value, plus

±0.5 % of measuring range

Resolution 100 µV — 100 mV (depending

on measuring range)

*)

The measuring ranges in measurement modes "U" and "I" are

specified as peak-to-peak values. Consequently, the digital

display box is "grayed out" if the set measuring range is briefly

exceeded (overload).

7.4.3 Resistance measurement (CH1)

Property Value/Range

Measuring range 100  — 1 M

Accuracy up to 200 K ±0.75 % of measured value

plus ±0.25 % of measuring ran-

ge

Accuracy up to 1 M ±2 % of measured value

plus ±0.25 % of measuring ran-

ge

Resolution 0.1  — 1000 (depending on

measuring range)

Input resistance > 9 M

1 689 989 072 2010-06-09| Robert Bosch GmbH

18 | KTS 340 | Technical dataen

7.4.4 Current measurement (CH1 and CH2)

Sensor Measuring range

Shunt (CH1 only) ±600 mA

30 A clamp (CH1 only) ±30 A

100 A clamp ±100 A

600 A clamp ±600 A

1000 A clamp (CH1 only) ±1000 A

7.4.5 Continuity tester (CH1)

Property Value/Range

Measurement current 2 mA

No-load voltage ≤ 5 V

Continuity < 10  (with acoustic check-back)

7.4.6 Diode measurement (CH1)

Property Value/Range

Measurement current 2 mA

No-load voltage ≤ 5 V

Maximum diode voltage 2 V

7.5 WLAN

Standard: IEEE 802.11g (54 Mbit/s), compatible with

IEEE 802.11b (11 Mbit/s), data encryption: OPEN, WPA,

WPA-PSK, WPA2, WPA2-PSK, WEP (64/128/256 bits),

antenna: -3dBi.

Radio link

KTS 340 to PC/laptop

Minimum range

Workshop environment with clear view

of access point

30 meters

In vehicle interior with vehicle door or

window open and engine running

10 meters

The range of the WLAN varies considerably.

20–40 m can normally be achieved indoors and up to

100 m outdoors.

Under adverse conditions the effective range may only

be 10–15 m or even less.

The KTS 340 automatically adapts the transmission

rate in the WLAN to the transmission conditions. In the

event of a poor radio link the data are transmitted

Bosch KTS 340 Original Instructions Manual

Bosch KTS 340 Original Instructions Manual

dans d''autres langues

Documents connexes

Autres documents