Honeywell PRO 1000 Vertical Non-Programmable Thermostat Manuel utilisateur

69-2798EFS-03

PRO 1000 Series

Non-Programmable Thermostat

Operating Manual

Cool

On

Off

Heat

Cool

Auto

On

Fan

Read before installing.

Need Help?

For assistance with this product please visit Honeywellhome.com/support

® U.S. Registered Trademark. Patents pending.

CAUTION: EQUIPMENT DAMAGE HAZARD.

To prevent possible compressor damage, do not operate cooling system when

outdoor temperature is below 50°F (10°C).

This manual covers the following models:

TH1100DV: For 1 Heat systems

TH1110DV: For 1 Heat/1 Cool systems

TH1210DV: For 2 Heat/1 Cool heat pump systems

(Pull thermostat from wallplate and turn over to find model number.)

1 69-2798EFS—03

About your new thermostat

Thermostat features ..................................2

Quick reference to controls .................... 3

Quick reference to display ......................4

Operation

Select system setting ................................ 5

Select fan setting ........................................6

Adjust the temperature ............................7

Compressor protection.............................8

Appendices

Battery replacement ..................................9

Customer assistance .............................. 10

In case of difficulty .................................. 11

Limited warranty ....................................... 13

Table of contents

69-2798EFS—03 2

Your new Resideo thermostat has been designed to give you many years of

reliable service and easy-to-use, push-button climate control.

Features

• Backlit display is easy to read

• Displays ambient (measured) temperature at all times

• One-touch access to setpoint temperature

• Built-in compressor protection

About your new thermostat

3 69-2798EFS—03

M34675

Set

Cool

77

On

Fan

Auto

On

Off

Cool

Heat

Quick reference to controls

Up/Down buttons

Press to adjust

temperature.

Fan Switch (see page 6)

On: Fan runs continuously.

Auto: Fan runs only when heating

or cooling system is on.

System switch (see page 5)

• Cool: Cooling system control.

• Off: All systems off.

• Heat: Heating system control.

• Em Heat: Emergency & Auxiliary

Heat control. Compressor is locked

out. (Select models only.)

69-2798EFS—03 4

Lo

Batt

Set

Cool

77

M34802

On

Quick reference to display screen

Low battery warning

(see page 9)

Temperature

The ambient (measured)

temperature is normally

displayed. To view the

setpoint temperature,

press the Up or Down

button once. The setpoint

temperature will appear for

five seconds.

System status

Cool on: Cooling system is on.

Heat on: Heating system is on.

Aux On: Auxiliary heat is on. (Only for heat pumps with this capability [select models

only].)

When “Heat On” or “Cool On” is flashing, compressor protection is engaged (see page 8).

Setpoint indicator

Appears when the setpoint

temperature is displayed

5 69-2798EFS—03

M34675

Set

Cool

77

On

Fan

Auto

On

Off

Cool

Heat

Select the system setting

The SYSTEM switch can be set to control

your heating or cooling system, depending

on the season.

• Cool: Cooling system control.

• Off: All systems are off.

• Heat: Heating system control.

• Em Heat: Emergency & Auxiliary Heat

control. Compressor is locked out.

(Select models only.)

Set SYSTEM

switch to

control the

heating

or cooling

system.

CAUTION: EQUIPMENT DAMAGE

HAZARD. To prevent possible

compressor damage, do not operate

cooling system when outdoor

temperature is below 50°F (10°C).

69-2798EFS—03 6

M34675

Set

Cool

77

On

Fan

Auto

On

Off

Cool

Heat

Select the fan setting

Set the FAN switch to Auto or On.

In “Auto” mode (the most commonly

used setting), the fan runs only when

the heating or cooling system is on.

If set to “On,” the fan runs continuously.

Set FAN switch to

choose whether

the fan runs

continuously or

only as needed.

7 69-2798EFS—03

M34675

Set

Cool

77

On

Fan

Auto

On

Off

Cool

Heat

Adjust the temperature

Press s or t to adjust the

temperature.

Note: Make sure the thermostat

is set to the system you want to

control (heat or cool).

69-2798EFS—03 8

Set

Cool

77

M32769

On

Built-in compressor protection

This feature helps prevent damage to the com-

pressor in your air conditioning or heat pump

system.

Damage can occur if the compressor is

restarted too soon after shutdown. This fea-

ture forces the compressor to wait 5 minutes

before restarting.

During the wait time, the display will flash the

message Cool On (or Heat On if you have a

heat pump model). When the safe wait time

has elapsed, the message stops flashing and

the compressor turns on.

Message flashes until

safe restart time has

elapsed.

9 69-2798EFS—03

M34673

M34676

Set

Cool

77

On

Fan

Auto

On

Off

Cool

Heat

C IS OPTIONAL

WITH BATTERIES

RC

R

C

W

Y

G

O

B

Battery replacement

Install two fresh AAA batter-

ies when Lo Batt flashes on

the screen. Lo Batt appears

for 60 days before the batter-

ies are depleted.

Replace batteries once a

year, or when you will be away

for more than a month.

The settings are stored in

non-volatile (permanent)

memory and are thus pre-

served when the thermostat

is without batteries.

Pull at bottom to

remove thermostat

from wallplate.

Turn thermostat over,

insert fresh AAA alka-

line batteries, then

reinstall thermostat.

69-2798EFS—03 10

M34673

M34676

Set

Cool

77

On

Fan

Auto

On

Off

Cool

Heat

C IS OPTIONAL

WITH BATTERIES

RC

R

C

W

Y

G

O

B

Customer assistance

For assistance with this product,

please visit

Honeywellhome.com/support.

Turn thermostat over

to find model number

and date code.

Pull at bottom to

remove thermostat

from wallplate.

To save time, please note

your model number and

date code before calling.

11 69-2798EFS—03

If you have difficulty with your thermostat, please try the following sugges-

tions.

Most problems can be corrected quickly and easily.

Display is blank

• Check circuit breaker and reset if necessary.

• Make sure power switch at heating & cooling system is on.

• Make sure furnace door is closed securely.

• Make sure fresh AAA alkaline batteries are correctly installed

(see page 9).

Heating or cooling

system does not

respond

• Set system switch to Heat (see page 5). Make sure the

temperature is set higher than the Inside temperature.

• Set system switch to Cool (see page 5). Make sure the

temperature is set lower than the Inside temperature.

• Wait 5 minutes for the system to respond.

In case of difficulty

69-2798EFS—03 12

Temperature

settings do not

change

Make sure heating and cooling temperatures are set to acceptable

ranges:

• Heat: 40° to 90°F (4.5° to 32°C).

• Cool: 50° to 99°F (10° to 37°C).

“Heat On” or

“Cool On” is

flashing

• Compressor protection feature is engaged. Wait 5 minutes for

the system to restart safely, without damage to the compressor

(see page 8).

“Heat On” is not

displayed

• Set the System switch to Heat, and set the temperature level

above the current room temperature (see page 5).

“Cool On” is not

displayed

• Set the System switch to Cool, and set the temperature level

below the current room temperature (see page 5).

In case of difficulty

13 69-2798EFS—03

For warranty information go to Honey wellhome .com/support

2-year limited warranty

CAUTION: MERCURY NOTICE.

If this product is replacing a control that contains mercury in a sealed tube, do not

place the old control in the trash. Contact your local waste management authority for

instructions regarding recycling and proper disposal.

CAUTION: ELECTRONIC WASTE NOTICE.

The product should not be disposed of with other household waste. Check for the nearest

authorized collection centers or authorized recyclers. The correct disposal of end-of-life

equipment will help prevent negative consequences for the environment and human

health.

FCC statement at:

https://customer.resideo.com/enUS/support/residential/codes-and-standards/

FCC15105/Pages/default.aspx

Resideo Technologies Inc.

1985 Douglas Drive North, Golden Valley, MN 55422

https://www.honeywellhome.com/support

692798EFS03 M.S. Rev. 0820 | Printed in United Stateswww.resideo.com

The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufac-

tured by Resideo Technologies, Inc. and its affiliates.

International, Inc. Ce produit est fabriqué par Resideo Technologies, Inc. et ses sociétés affiliées.

International, Inc. Este producto es fabricado por Resideo Technologies, Inc. y sus afiliados.

69-2798EFS-03

Cool

On

Off

Heat

Cool

Auto

On

Fan

Série PRO 1000

Thermostat non programmable

Manuel d’utilisation

Série PRO 1000

Thermostat non programmable

Le présent mode d’emploi porte sur les modèles suivants :

TH1100DV: Pour systèmes à un étage de chauffage

TH1110DV: Pour systèmes à un étage de chauffage/1 étage de refroidissement

TH1210DV: Pour thermopompes à 2 étages de chauffage/1 étage de refroidissement

seulement

(Retirer le thermostat de la plaque murale et le retourner pour trouver le numéro de

modèle.)

Besoin d’aide?

Pour obtenir de l’assistance au sujet de ce produit, consulter le

Honeywellhome.com/support

Lire avant l’installation.

® Marque déposée aux É.-U. Brevets en instance.

MISE EN GARDE : RISQUE DE DOMMAGE MATÉRIEL.

Pour éviter d’endommager le compresseur, ne pas faire fonctionner le système

de refroidissement lorsque la température extérieure est inférieure à 10 °C

(50 °F).

1 69-2798EFS—03

Table des matières

Votre nouveau thermostat

Caractéristiques du thermostat ...........2

Coup d’oeil rapide sur

les commandes ............................................3

Coup d’oeil rapide sur l’affichage .......4

Programmation et fonctionnement

Sélectionner le réglage du système ..5

Sélectionner le réglage du

ventilateur .......................................................6

Régler la température ...............................7

Protection du compresseur ...................8

Appendices

Remplacement des piles ......................... 9

Services à la clientèle ............................. 10

En cas de difficulté ..................................11

Garantie limitée ......................................... 13

69-2798EFS—03 2

À propos du thermostat

Votre nouveau thermostat Resideo a été conçu pour vous procurer

de nombreuses années de service fiable et assurer la régulation de la

température ambiante avec facilité, par simple bouton-poussoir.

Caractéristiques

• L’affichage rétroéclairé est facile à lire

• Affichage permanent de la température ambiante (mesurée).

• Accès à l’aide d’une seule touche à la température du point de consigne.

• Protection intégrée du compresseur.

La page charge ...

Honeywell PRO 1000 Vertical Non-Programmable Thermostat Manuel utilisateur

Honeywell PRO 1000 Vertical Non-Programmable Thermostat Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents