HearthStone Bristol DX Le manuel du propriétaire

Hearthstone Quality Home Heating Products, Inc. ®

Bristol DX Model 8762

Manual: 6400-40466

R: 3/26/2013

Bristol DX

(Model 8762)

GAS-FIRED DIRECT-VENT HEATER

Owner's Manual

Installation & Operating

Instructions

Read This Manual in Its Entirety

Operate And Maintain This Gas Heater

According To This Instruction Manual.

SAVE THESE INSTRUCTIONS!

WARNING: FOLLOW THE INFORMATION IN

THESE INSTRUCTIONS EXACTLY, IF NOT, A FIRE

OR EXPLOSION MAY RESULT CAUSING

PROPERTY DAMAGE, PERSONAL INJURY OR

LOSS OF LIFE.

WARNING: DO NOT STORE OR USE GASOLINE

OR ANY OTHER FLAMMABLE VAPORS AND

LIQUIDS NEAR THIS OR ANY OTHER GAS

APPLIANCE.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch electrical switches; do not use the phone

in your building.

Immediately call your gas supplier from a phone

outside the structure. Follow your gas supplier’s

instructions.

If you cannot reach your gas supplier, call the fire

department or 911.

A qualified installer, service agency, or gas supplier must

perform installation and service of this appliance. In the

Commonwealth of Massachusetts, all installation of gas

lines and gas fittings must be performed by a licensed gas

fitter or licensed plumber.

AVERTISSEMENT: ASSUREZ-VOUS DE BIEN

SUIVRE LES INSTRUCTIONS DONNÉ DANS

CETTE NOTICE POUR RÉDUIRE AU MINIMUM LE

RISQUE D’INCENDIE OU POUR ÉVITER TOUT

DOMMAGE MATÉERIEL, TOUTE BLESSURE OU

LA MORT.

AVERTISSEMENT: NE PAS ENTRESPOSER NI

UTILISER D’ESSENCE NI D’AUTRE VAPERURS

OU LIQUIDES INFLAMMABLES DANS LE

VOISINAGE DE CET APPRAREIL OU DE TOUT

AUTRE APPAREIL.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

Ne pas tenter d’allumer d’appareil.

Ne touchez à aucun interrupteur. Ne pas vous servir

des téléphones se trouvant dans le batiment où vous

vous trouvez.

Appelez immédiatement votre fournisseur de gaz

depuis un voisin. Suivez les instructions du

fournisseur.

Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service dos incendies.

L’installation et service doit être exécuté par un qualifié

installer, agence de service ou le fournisseur de gaz.

Intentionally Blank

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

3

Information Sheet

Use this page to record all relevant information concerning the purchase, installation, and maintenance of your

Bristol DX Model 8762 Direct -Vent heater. This information will facilitate servicing, purchase of replacement

parts, and warranty claims (if necessary). Keep your original receipt in a safe place as proof of purchase.

Serial Number:

Fuel type:

Natural Gas

Liquid Propane

Sold by:

Date of Purchase:

Address:

Phone:

E-mail

Website:

Installed by:

Date of Installation:

Address:

Phone:

E-mail

Website:

Gas Supplier:

Address:

Phone:

E-mail

Website:

Read this Owner’s Manual before installing, or operating your BRISTOL DX. Retain this manual for future

reference.

SERVICE RECORD

Date

Who Performed Work

Work Performed

Notes:

WHAT WHEN

Firebox Cleaning............. annually

Glass Cleaning................ as needed

Door Gasket.................... Replacement as needed

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

4

Table of Contents

INTRODUCTION ........................................................................................................................................................... 5

SAFETY INFORMATION ................................................................................................................................................ 6

PROFLAME CONTROL SYSTEM & FEATURES ................................................................................................................ 8

Bristol DX 8762 Model Overview ................................................................................................................................ 8

Control Functions ..................................................................................................................................................... 10

SPECIFICATIONS ....................................................................................................................................................... 12

INSTALLATION PREPARATION .................................................................................................................................... 13

Codes ....................................................................................................................................................................... 13

Items Required for Installation .................................................................................................................................. 13

Packing List .............................................................................................................................................................. 13

Unpacking and Inspection ........................................................................................................................................ 13

CLEARANCES TO COMBUSTIBLES .............................................................................................................................. 16

Clearance to Combustibles ...................................................................................................................................... 16

Hearth Requirement/Floor Protection ....................................................................................................................... 16

VENTING INFORMATION ............................................................................................................................................. 18

Venting Components ................................................................................................................................................ 18

Minimum Venting Installation Instructions ................................................................................................................ 22

ELECTRICAL SYSTEM INFORMATION .......................................................................................................................... 25

GAS SUPPLY & CONNECTIONS .................................................................................................................................. 26

Gas Connections ...................................................................................................................................................... 27

LOG SET, & SCREEN PLACEMENT ............................................................................................................................. 28

Installation of the Log Set ......................................................................................................................................... 28

Installation of the Optional Screens .......................................................................................................................... 29

Removal of Log Set .................................................................................................................................................. 29

Completing the Installation ....................................................................................................................................... 29

LIGHTING & OPERATION ........................................................................................................................................... 30

Lighting Instructions .................................................................................................................................................. 30

Initial Adjustments .................................................................................................................................................... 31

Daily Operation ......................................................................................................................................................... 32

ROUTINE MAINTENANCE & CARE .............................................................................................................................. 34

Cleaning ................................................................................................................................................................... 34

Monthly (or as needed): ............................................................................................................................................ 34

Annually: ................................................................................................................................................................... 34

As Needed: ............................................................................................................................................................... 35

PARTS LIST .............................................................................................................................................................. 37

TROUBLESHOOTING .................................................................................................................................................. 38

RATING LABEL ......................................................................................................................................................... 40

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

5

Introduction

Congratulations on your purchase of the Bristol DX

Model 8762, Gas-Fired Direct-Vent heater. The

Bristol, by Hearthstone, incorporates the latest in

direct vent gas technology, which will provide you

with ease of use, clean, and efficient heat for years

to come. The Bristol’s copious three sides of glass,

sleek styling, and enameled or painted cast iron

gives the Bristol ambiance and a pleasing look that

is maintained with minimum care.

However, as with any gas appliance, the unit must

be properly and safely installed and maintained by

qualified service personnel to ensure safe and

trouble-free operation.

Bristol DX Model 8762 features:

1. Proflame 2 GTMFS Control System

2. 5-piece log set

3. Platinum Bright Embers

4. The option to toggle back and forth between an

Intermittent (IPI) or Continuous (CPI) pilot mode

via the remote control.

a. The IPI mode allows the most efficient

use of gas, burning the pilot only when

the thermostat calls for the burner to

ignite.

b. The CPI mode runs the pilot

continuously keeping the firebox warmer

thus promoting better draft in colder

climates.

5. Battery backup for functionality during power

outages.

6. Blower Assembly

7. Optional Screen Kit

The Proflame GTMFS System Features:

1. Thermostatic Remote Control

a. Six (6) flame levels, adjustable via the

remote

b. Split Burner control via remote

c. Six (6) blower speeds, adjustable via the

remote

d. Thermostatic mode to turn on/off based

upon room temperature.

e. “Smart” thermostatic mode to modulate

flame levels automatically as the unit

approaches the set point temperature.

f. Additional AC receptacle controlled

(on/off) by the remote.

2. “Child-safe” lock-out on remote control.

3. “Low Battery” indicator for Transmitter on remote

control

Part #

Description

8762-0010

Matte Black

8762-0020

Brown Enamel

8762-0083

Basil Enamel

Read this Owner’s Manual

Operate and maintain this gas heater according to

the instructions in this manual. For your safety, and

years of trouble free operation, read this manual in

its entirety.

Heater Must Be Installed and Maintained By

Qualified Service Personnel

Verify the gas connections and that venting systems

supply adequate combustion and ventilation air to

meet the requirements of local, regional or national

installation codes. Qualified service personnel must

inspect the gas heater before use, and at least

annually.

Manufactured & warranted by:

Hearthstone Quality Home heating Products, Inc.

317 Stafford Ave.

Morrisville, VT 05661

www.hearthstonestoves.com

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

6

Safety Information

Your Bristol is an attractive and extremely efficient

and easy to use heater, utilizing today’s best

technologies. By following a few simple safety

precautions and by performing minimal

maintenance, the unit will remain appealing while

providing years of quality performance.

The installation must conform to local codes or, in

the absences of local codes, the current National

Fuel Gas Code, ANSI Z223.1 (NFPA 54) or

CAN/CGA B149 Installation Code. (Installer

l’appareil selon les codes ou réglements locaux, ou,

en l’absence de tells réglements, selon les Codes

d’installation CAN/CGA B149.)

CAUTION: DO NOT USE THIS APPLIANCE IF ANY

PART WAS UNDER WATER. IMMEDIATELY CALL

A QUALIFIED SERVICE TECHNICIAN TO INSPECT

THE HEATER AND TO REPLACE ANY PART OF

THE CONTROL SYSTEM AND GAS CONTROL

THAT HAS BEEN UNDER WATER. (NE PAS SE

SERVIR DE CET APPAREIL S’IL A ÉTÉ PLONGÉ

DANS L’EAU, COMPLÉTEMENT OU EN PARTIE.

APPELER UN TECHNICIEN QUALIFIÉ POUR

INSPECTOR L’APPAREIL ET REMPLACER TOUTE

PARTIE DU SYSTÉME DE CONTRÔLE ET TOUTE

COMMANDE QUI ONT ÉTÉ PLUNGES DANS

L’LAU.)

During the first few hours of operation the appliance

may produce smoke and/or odor. This is normal

during the first several burns and also after long

periods when the stove is not burned. During these

initial burns, open a window(s) to assist in the

removal of the smoke/odor.

The appliance and its individual shutoff valve must

be disconnected from the gas supply piping system

during any pressure testing of that system at test

pressures in excess of ½ psig. (3.5k Pa). The

appliance must be isolated from the gas supply

piping system by closing its individual manual

shutoff valve during any pressure testing of the gas

supply piping system at test pressures equal to or

less than ½ psig (3.5k Pa).

Fire Hazard

Do not store or use gasoline, other flammable

vapors or liquids in the vicinity of this appliance.

Locate the Bristol out of traffic areas and away from

furniture, draperies, clothing, and flammable

material.

Vent Only to the Outside

Never vent the gas heater to other rooms or

buildings.

Service Caution

If you believe your Bristol is not in any way

performing properly, immediately discontinue

operation until the unit is inspected and approved by

qualified service personnel. Prior to servicing the

unit, turn the gas to the valve off, and disconnect

any electrical source. Ensure the unit is cool prior to

servicing and cleaning. Replace any safety screen,

guard, or component removed during servicing

prior to operation. Use of any components not

supplied by Hearthstone on the stove voids all

warranties. Do not substitute components.

Proper Fuel

This gas heater is designed to burn natural gas (NG)

or with conversion, liquid propane (LP). Never burn

any fuel gas not intended for use with this unit.

Never burn paper, wood, or other materials in this

appliance.

This heater is factory equipped to burn natural gas

(NG). To burn propane (LP), you must purchase an

LP conversion kit 97-56621.

This appliance is only for use with the type(s) of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a

certified kit is used. Cet appareil doit être atilisé

uniquement avec les types de gas indiqués sur la

plaque signalétique. Ne pas l’utiliser avec d’autres

gas sauf si un kited conversion certifié est installé. )

WARNING: THIS GAS APPLIANCE MUST NOT BE

CONNECTED TO A CHIMNEY FLUE SERVING A

SEPARATE GAS OR SOLID-FUEL BURNING

APPLIANCE

WARNING: DO NOT OPERATE THE APPLIANCE

WITH THE FRONT GLASS REMOVED, CRACKED,

OR BROKEN. REPLACEMENT OF GLASS

SHOULD BE DONE BY A LICENSED OR

QUALIFIED SERVICE PERSON. ONLY OPEN

FRONT FOR ROUTINE SERVICE. DO NOT SLAM

FRONT OR STRIKE GLASS.

WARNING: HEARTHSTONE RECOMMENDS THAT

ONLY AN NFI CERTIFIED SERVICE TECHNICIAN

INSTALLS, AND REPAIRS THIS APPLIANCE. A

QUALIFIED SERVICE TECHNICIAN MUST

INSPECT THE APPLIANCE BEFORE USE, AND AT

LEAST ANNUALLY. MORE FREQUENT CLEANING

MAY BE REQUIRED DUE TO EXCESSIVE LINT

FROM CARPETING, BEDDING MATERIAL, PETS,

ETC. IT IS IMPERATIVE THAT THE CONTROL

COMPARTMENTS, BURNERS, AND CIRCULATING

AIR PASSAGES OF THE APPLIANCE ARE KEPT

CLEAN AND FREE OF OBSTRUCTIONS.

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

7

(S’ASSURER QUE LE BRÛLEUR ET LE

COMPARTIMENT DES COMMANDES SONT

PROPRES. VOIR LES INSTRUCTIONS

D’INSTALLATION ET D’UTILISATION QUI

ACCOMPAGNENT L’APPAREIL.)

Hot Surfaces

Certain exposed surfaces of the Bristol will reach

high temperatures during normal operation.

Clearances to combustibles must be maintained, as

specified in the “Clearances To Combustibles”

section of this manual.

DUE TO HIGH TEMPERATURES THE APPLIANCE

SHOULD BE LOCATED OUT OF TRAFFIC AND

AWAY FROM FURNITURE, DRAPERIES,

CLOTHING AND FLAMMABLE MATERIALS.

CHILDREN AND ADULTS SHOULD BE ALERTED

TO THE HAZARDS OF HIGH SURFACE

TEMPERATURES AND SHOULD STAY AWAY TO

AVOID BURNS TO SKIN OR CLOTHING IGNITION.

CAREFULLY SUPERVISE YOUNG CHILDREN

WHEN THEY ARE IN THE SAME ROOM AS THE

APPLIANCE. TODDLERS, YOUNG CHILDREN,

AND OTHERS MAY BE SUSCEPTIBLE TO

ACCIDENTAL CONTACT BURNS. A PHYSICAL

BARRIER IS RECOMMENDED IF THERE ARE AT

RISK INDIVIDUALS IN THE HOUSE. TO RESTRICT

ACCESS TO A FIREPLACE OR STOVE, INSTALL

AN ADJUSTABLE SAFETY GATE TO KEEP

TODDLERS, YOUNG CHILDREN, AND OTHER AT

RISK INDIVIDUALS OUT OF THE ROOM AND

AWAY FROM HOT SURFACES.

CLOTHING OR OTHER FLAMMABLE MATERIAL

SHOULD NOT BE PLACED ON OR NEAR THE

APPLIANCE. (SURVEILLE LES ENFANTS.

GARDER LES VÊTEMENTS, LES MEUBLES,

L’ESSENCE OU AUTRES LIQUIDES À VAPEUR

INFLAMMABLES LIN DE L’APPAREIL.)

CLEAN THE AREA AROUND, UNDER, AND

BEHIND THE UNIT ON A REGULAR BASIS TO

PREVENT THE ACCUMULATION OF DUST AND

LINT.

Ceramic Logs, & Burner

If the decorative ceramic log, or burner material

supplied with the Bristol is damaged or parts are

missing, they must be replaced with the same, or

approved Hearthstone replacement parts. These

components affect the combustion quality and safety

of the heater. Do not replace ceramic logs, or the

burner with unapproved ceramic components or any

other material.

We recommend you always wear gloves and safety

goggles while handling the ceramic log set, and

burner materials.

Electrical Hazard

If present, any three-prong grounded plug must be

plugged directly into a properly grounded three-

prong receptacle. Do not cut or remove the

grounding prong from any plug or otherwise attempt

to circumvent the grounding protection provided with

the unit. The Bristol must be electrically grounded in

accordance with local codes, or in the absence of

local codes, with the National Electrical Code,

ANSI.NFPA 70 in the U.S. or CSA C22.1 Canadian

Electrical Code in Canada.

Do Not Light Pilot or Burner by Hand

The pilot light on this gas heater is lit using an

electronic ignition module as described elsewhere in

this manual. Never attempt to light the pilot or main

burner by hand with a match or lighter.

Mobile Home Installations

This appliance may be installed in an aftermarket

permanently located, manufactured (mobile) home,

where not prohibited by local codes. (Cet appareil

peut être installé dans un maison préfabriquée

(mobile) déjá installée á demeure si les réglements

locaux le permettent.

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

8

Proflame 2 Control System & Features

NOTE: OPEN DOOR UNDER THE ASH LIP AND DROP DOWN THE MODESTY PANEL FOR ACCESS TO

ELECTRICAL AND GAS CONNECTIONS.

Bristol DX 8762 Model Overview

Proflame 2 GTMFS System

The Proflame 2 GTMFS is a modular remote control

system that directs the functions of the Bristol. The

Proflame 2 GTMFS System is configured to control

the on/off, main/split burner operation, its flame

levels, and provides Manual and Smart thermostatic

control of the hearth appliance. The system controls

two remotely actuated 120V/60Hz power outlets. The

Fan outlet controls the fan speed through six levels,

and the Auxiliary outlet either on or off. There is also

an additional constantly powered 120V/60Hz outlet.

The system has battery backup power for burner

operation and control during power outages (see

page 9 for specifications).

Figure 1 - Proflame 2 Remote Transmitter

Remote Transmitter

The Bristol comes equipped with a thermostatic

remote control transmitter. The easy to read LCD

display shows all functional abilities as well as a

childproof lockout and low battery indicator. It

displays room temperature readout, set temperature

readout and function status. The remote transmitter is

powered by three 1.5 volt AAA batteries. A Mode Key

is provided to index between the features and a

Thermostat Key is used to turn on/off or index

through thermostat functions.

Figure 2 – Proflame Receiver

Back-up Battery Holder- On/Remote/Off

Switch

The back-up battery holder is powered (6V DC) by

the Control Board and uses four 1.5 volt AA type

batteries for backup during power outages. The slider

switch is set to one of three positions: ON (Manual

Override), REMOTE (Remote Control) or OFF. The

ON selection turns the valve on (to high), and

activates the split flow setting last used if the Remote

becomes inoperative.

Figure 3 – Proflame 2 Fan Control Module

Proflame 2 Control Board

This is the command center for the appliance. The

Control Board allows the pilot to run in the

Intermittent (IPI) mode or the Constant (CPI) mode.

The pilot mode can be toggled between IPI and CPI

via the remote control. The Control Board signals the

burner to light or shut down and provides the ignitor

with the electricity needed for sparking. It is the main

power supply for the entire system when 120V power

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

9

is available or by the batteries in the Back-up Battery

Holder during a power outage.

The Control Board is equipped with a three-prong

(grounding) plug for protection against shock hazard

and should be plugged directly into a properly

grounded three-prong receptacle. Do not cut or

remove the grounding prong from the plug.

SIT Modulating Gas Valve

The remote transmitter can modulate the valve and

the flame to 6 different settings between high and

low. You can modulate the flame via the remote

yourself or by setting the remote control to the Smart

Thermostat modulation mode. Smart mode means

that as the room temperature approaches the limit set

for shut down the valve will automatically gradually

step down the flame height. The reverse happens

when the room cools - the valve will automatically

gradually increase the flame height.

SIT Split Burner Solenoid

The remote transmitter can toggle between dual

burner, and single burner mode (35,000 Btu/hr or

12,000 Btu/hr).

Pilot Assembly

The pilot assembly consists of a pilot hood, sensor

rod, and ignitor. The ignitor sends a spark to the pilot

hood which ignites the gas and lights the pilot. With

the pilot lit the sensor rod is engulfed by the flame,

flame rectification occurs and the appliance remains

lit. If the sensor does not stay engulfed by the flame

the main burner will not light and the pilot will shut

down.

Figure 4 - Proflame GTMFS Component Specifications

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

10

Control Functions

Pilot Mode

Continuous Pilot (CPI): Running the Bristol 8762 in CPI mode will keep your pilot on even when the thermostat

does not call for heat and when the burner is not lit. This is an advantage in cold climates or under windy

conditions. The “standing pilot” helps to keep the venting warm and generate some draft within the system. The

standing pilot also keeps the firebox warm – greatly minimizing, or eliminating condensation formation on the

glass during startup. The ignitor will automatically spark whenever the pilot mode is switched to CPI, regardless

of the position of the receiver switch. Hearthstone recommends the use of the CPI mode during the heating

season.

Intermittent Pilot (IPI): Using the IPI mode is a more efficient use of fuel as the pilot only ignites when the

thermostat calls for heat.

To switch back and forth between the two pilot modes 1) Press the OFF button on the remote 2) Press the

Mode button on the remote. 3) Press Up or Down on the center pad to toggle back and forth between the two

modes.

Back –up Battery Holder- On/Remote/Off Switch

The Back-up Battery Holder is normally powered by the Proflame 2 Control Board or by four 1.5V AA batteries

during a power outage. This On/Remote/Off switch can be set to three different positions:

On: Manual override allowing the valve to function and ignite the burner without the remote transmitter. The

ignitor will spark automatically.

Remote: Remote Transmitter controls all functions of components.

Off: Turns off the stove. If CPI mode is selected, pilot will remain lit.

PRG Key: Used to synchronize the Transmitter and Receiver initially, and after each battery change (see page

35).

Figure 5 - Receiver Detail

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

11

Remote Transmitter

Figure 6 - Remote Transmitter Function Keys (remote color may differ from shown)

ON/OFF Key: Controls the insert.

Thermostat Key: This is the function that sets either

the Manual or Smart thermostatic control.

UP/Down Arrow Key: Adjusts the thermostat

temperature range, flame settings, split flow, and fan

speed.

Mode Key: Toggles through the component to be

controlled (split flow burner, blower or auxiliary

outlet)

The transmitter features a user-friendly layout with a

Blue LCD Screen for easier viewing.

See the instructions provided with the remote for

more operation details.

Figure 7 - Remote Transmitter Display Data

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

12

Specifications

LISTED: Gas-Fired Direct-Vent Fireplace Heater

Model: Bristol Direct-Vent Gas Fireplace

Heater (8762)

Testing Agency: Intertek Testing Services

NA, Inc. (ITS)

Tested to: ANSI Z21.88-09, CSA 2.33-09,

CAN/CGA2.17-M91

Certified for Canada, CSA P.4.1-02

Approved for Mobile Home Installation (see

page 7)

Certified for use by:

Board of State Examiners of Plumbers & Gasfitters

100 Cambridge Street, Room 1511

Boston, MA 02202

www.mass.gov

Figure 8 - Model 8762 Dimensions (Inches)

Specification

NG

LP

INPUT RATING (Btu/hr) 0-2000 ft (0-610 m)

36,000

33,000

INPUT RATING (Btu/hr) 2000-4500 ft (610-1370 m)

35,000

30,000

MAXIMUM OUTPUT (Btu/hr) 0-2000 ft (0-610 m)

28,200

26,200

MINIMUM INPUT (btu/hr) 0-2000 ft (0-610 m)

16,000

10,000

ORIFICE SIZE (DMS) 0-2000 ft (0-610 m (front/rear))

43/46

54/57

ORIFICE SIZE (DMS) 2000-4500 ft (610-1370 m (front/rear))

43/47

55/59

MANIFOLD PRESSURE - (in. W.c./kpa)

3.5/0.87

10.0/2.48

MANIFOLD PRESSURE - Low setting (in. W.c./kpa)

1.1/.027

6.4/1.59

INLET PRESSURE - MINIMUM (in.w.c./kpa)

5.0/1.25

12.0/2.99

INLET PRESSURE – MAXIMUM (in. w.c./kpa)

7.0/1.74

13/3.22

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

13

Installation Preparation

Codes

Adhere to all local codes or, in their absence, the

latest edition of THE NATIONAL FUEL GAS CODE

ANSI Z223.1 (NFPA 54) or CAN/CGA B149 (Installer

l’appareil selon les codes ou règlements locaux, ou,

en l’absence de tels règlements, selon les Codes

d’installation CAN/CGA-B149.)

Installation Codes can be obtained from:

AMERICAN NATIONAL STANDARDS

INSTITUTE, INC.

1430 BROADWAY

NEW YORK, NY 10018

www.ansi.org

NATIONAL FIRE PROTECTION ASSOCIATION,

INC.

BATTERY MARCH PARK

QUINCY, MA 02269

www.nfpa.org

The appliance when installed must be electrically

connected and grounded in accordance with local

codes or, in the absence of local codes, with the

current NFPA 70-National Electrical Code or CSA

C22.1-Canadian Electric Code.

A manufactured home (mobile) OEM installation must

conform to the Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280 (U.S.) or

Standard for Manufactured Home Installation,

ANSI/NCBCS A225.1 or Standard for Gas Equipped

Recreational Vehicles and mobile Housing, CSA

Z240.4.CAN/SCA Z240 MH (Canada). (Installer

l’appareil selon les codes ou règlements locaux, ou,

en l’absence de tels règlements, selon les Codes

d’installation CAN/CGA-B149.)

This appliance is equipped for use at 0 to 2000 feet

(0-610 meters) altitude. (Cet appareil est equipè pour

des altitudes compries entre 0 et 2000 pieds (0-610

m) seulement.)

WARNING: DO NOT INSTALL OR USE THIS

APPLIANCE IF ANY PART WAS SUBMERGED

UNDER WATER. IMMEDIATELY CALL A

QUALIFIED SERVICE TECHNICIAN TO INSPECT

THE HEATER AND TO REPLACE ANY PART OF

THE CONTROL SYSTEM AND GAS CONTROL

THAT WAS UNDER WATER. (NE PAS SE SERVIR

DE CET APPAREIL S’IL A ÉTÉ PLONGÉ DANS

L’EAU, COMPLÈTEMENT OU EN PARTIE.

APPELER UN TECHNICIEN QUALIFIÉ POUR

INSPECTOR L’APPAREIL ET REMPLACER TOUTE

PARTIE DU SYSTÈME DE CONTRÔLE ET TOUTE

COMMANDE QUI ONT ÉTÉ PLONGÉS DANS

L’LAU)

Items Required for Installation

Approved venting

External regulator (for propane (LP) only)

LP conversion kit (not included, for propane

only))

Piping which complies with local codes

Pipe sealant approved for use with

propane (LP) (resistant to sulfur compounds).

Manual shutoff valve

Sediment trap (see page 26)

120 volt electrical service

Pipe wrench

Phillips head screwdriver

7/16-inch wrench

3/16” hex wrench

Other parts as required by local code

Safety Glasses

Gloves

Packing List

1- Bristol DX 8762 Gas-Fired Heater

1- Owner’s Packet Envelope (manual, warranty card)

5- Decorative Ceramic Logs (in box on pallet)

1- Blower Assembly (on Stove)

4- ¼ x 20 x 1” Leg leveling screws

1- Accessory Box (on pallet) containing:

1- Remote Control w/batteries

1- Package of four AA Batteries

1- Bag of Platinum Bright Embers

1- Enamel Touch-up Paint (if applicable)

2- Orifice Gaskets and Instructions

Note: Vent kits and components are supplied

separately. Failure to use the venting

components approved by Hearthstone for this

appliance will void your warranty.

Unpacking and Inspection

Hearthstone packages your Bristol to withstand

normal shipment without damage. However, damage

can still occur during transit. Take care to inspect for

damage when unpacking and installing the unit.

DO NOT INSTALL, OR PUT INTO SERVICE, A

DAMAGED OR INCOMPLETE HEATER.

Remove the shrink-wrap and other packaging

materials taking care not to damage the stove’s

finish. Inspect the Bristol for visible or concealed

damage. The unit should be square and true. Any

sheet metal parts should be smooth and free of

bends and dents. Any enameled cast iron should be

free of chips or cracks. If visible or concealed

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

14

damage is found or suspected, contact your dealer

for instructions.

Always use gloves and eye protection when handling

the decorative ceramic fire logs, and burner. Use

care when handling these parts as they are fragile

and subject to damage and breakage if handled

roughly.

See the firebox access instructions on page 15 and

remove the log set. Unpack and inspect the logs for

damage. Inspect the ceramic burner. Open the other

boxes and inspect the components. If log, burner, or

any other component damage is encountered,

contact your dealer for a replacement. Otherwise, set

the logs and other components aside until called for

during the installation.

Dismounting from Pallet

With the accessory boxes removed and set aside,

remove the 4 lag bolts and clips that fasten the unit to

the pallet (see figure 10). Take care not to mar or

chip the stove’s finish.

Have someone help lift the stove up and off the

shipping stands and pallet, taking care to avoid

damaging components mounted under the stove.

Figure 9 – Shipping Clip Detail

Leg Leveler Screws

If your hearth surface in uneven, or is not level, you

can use the four provided leveling screws.

1. Completely remove the four carriage bolts

used for shipping the stove.

2. Replace them with the ¼ x 20 x 1” oval tip

set screws provided in the packing kit.

3. Install the leveling screws down through the

flanges on the feet (hex end up).

4. Adjust the screws only enough to keep the

stove from rocking or wobbling*.

*On thinner hearths, or hearth pads, adjusting the screws so the

entire stove’s weight is solely supported on them can cause

damage to your hearth.

Shipping Stand

Carriage Bolt

Lag

Bolt

Clip

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

15

Firebox Access

1. First, remove the top of the stove (lift off). Set

carefully aside on a soft surface.

2. Lift the front panel slightly to disengage the tangs

at its top – tilt the front toward you slightly and lift

it up out of the bottom slots and set aside on a

soft surface.

Figure 10 – Front Panel Mounting Tang Detail

Figure 11 – Front Panel Retaining Slots

3. If installed, remove the front screen by lifting it off

the glass frame.

4. Pull forward and disengage the spring clips

securing the top of the glass frame. See Figure

14. Tilt the top of the glass frame outward and lift

it off the studs on the bottom – set carefully

aside.

Figure 12 – Glass Spring Clip Detail

5. Lift glass frame off the lower mounting pins.

Figure 13 - Lower Mounting Stud/Spring Detail

See page 28 for log set installation. Reinstall

components by reversing the previous steps.

Ensure you slide the lower glass frame tangs

behind the spring keepers. If desired, you need

not reinstall the optional screens.

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

16

Clearances to Combustibles

Note: Ensure clearances are in accordance

with local installation codes and the

requirements of the gas supplier.

Clearance to Combustibles

Due to high surface temperatures, locate the unit out

of traffic areas and away from furniture and

draperies. Do not place clothing and other

flammable material on or near the heater. When

positioning the unit always maintain adequate

clearances around air openings into the combustion

chamber and allow for adequate ventilation.

Minimum clearances to combustibles must be

maintained as shown in Figures 15 - 17.

Note: The rear clearance to combustibles is

determined by either the unit’s or the vent pipe’s

minimum clearance, depending on whether the

installation calls for vertical rise within the room or a

rear exit, through-the-wall vent pipe.

Ensure you consider the need for access to the gas

control valve access door on the front of the unit as

well as full access for periodic cleaning and

servicing. Also consider clearance for the blower

assembly if present, or planned in the future.

CAUTION: THESE CLEARANCES REPRESENT

MINIMUM DISTANCES IN ALL CASES, WHICH,

THROUGH TESTING IN AN INDEPENDENT

LABORATORY TO ANSI AND CSA STANDARDS,

WILL PREVENT FIRE OR SPONTANEOUS

COMBUSTION. WE DO NOT CONTROL THE

COMBUSTIBLE MATERIALS EXPOSED TO HEAT

BY THIS PRODUCT; THEREFORE, AN

ASSESSMENT MUST BE MADE BY THE

INSTALLER TO PREVENT CONSEQUENTIAL

DAMAGE OF WALLS AND FLOORING.

Hearth Requirement/Floor

Protection

You can place the Bristol directly on any non-

combustible surface or on a wood floor. When

placing the Bristol on any other type of combustible

surface you must install a panel made of metal,

wood, stone, or glass under the appliance. The

panel must extending the full width and depth of the

appliance. Installations must meet all local codes.

Figure 14 - Minimum Wall Clearances

Figure 15 - Horizontal Vent Mantle Clearance

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

17

The corner clearance for the Bristol 8762 is 11”,

measured from the edge of the top castings, to the

adjacent wall.

Figure 16 - Corner Clearance

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

18

Venting Information

Venting Components

Starter collar is installed by Hearthstone.

Use the following instructions along with the pipe

manufacturer’s instructions to complete the

installation. Do not mix vent components from

different manufacturers within the same venting

system.

Approved Venting Manufacturers

The Bristol Direct Vent (8762) is approved for

installation only with the venting components

provided by manufactures listed on this page.

Simpson Dura-Vent, Inc.

P.O. Box 1510

Vacaville, CA 95696-1510 800-835-4429

American Metal Products (AmeriVent)

8601 Hacks Cross Rd.

Olive Branch, MS 38654 800-423-4270

Selkirk Corporation

1301 W. President George Bush Hwy, Suite 330

Richardson, TX 75080-1139 800-992-8368

Security Chimneys International Ltd (Secure Vent)

2125 Monterey, Laval, Quebec

Canada, H7L 3T6 450-973-9999

ICC, Inc.

400 J-F Kennedy, St. Jerome, Quebec

Canada, J7Y 4B7 450-565-6336

Metal-Fab, Inc.

P.O. Box 1138

Wichita, Kansas 67201 316-943-2351

Venting Terminations

The Bristol cannot be vented jointly with any other

solid fuel or gas appliance. It must be vented directly

to the outside of the building using a proper

termination as listed in this manual. After

determining the venting configuration for your stove,

select the vent system that will best accommodate

your installation.

CAUTION: ENSURE ALL STOVE AND

TERMINATION CAP CLEARANCES ARE

OBSERVED PER THIS OWNER’S MANUAL.

CAUTION: ENSURE THERE IS NO WIRING OR

PLUMBING IN THE CHOSEN LOCATION.

CAUTION: DO NOT RECESS VENTING

TERMINALS INTO A WALL OR SIDING.

Approved Venting Configurations

WARNING: IN HIGH WIND AREAS AND

PARTICULARLY COLD CLIMATES IT MAY BE

NECESSARY TO HEAT YOUR VENT SYSTEM

WITH THE PILOT PRIOR TO IGNITION OF THE

MAIN BURNER. IN THESE INSTANCES IT IS

RECOMMENDED THAT YOU LEAVE THE PILOT

RUNNING FOR 5 MINUTES PRIOR TO IGNITING

THE MAIN BURNER. THIS WILL ALLOW FOR

PROPER START UP AND IGNITION OF ALL

PORTS ON THE BURNER.

There are two types of venting configurations

approved for use with this appliance:

Vertical Venting/Vertical Termination

Vertical Venting/Horizontal Termination

Pipe Clearances to combustibles:

1" to vertical runs

1" below and to the side of horizontal runs

2" from the top of horizontal runs

Vertical Venting and Termination

The Bristol 8762 is approved for venting vertically

through a roof or ceiling. When installing a vertical

vent and/or vertical terminations you must adhere to

the following requirements:

When terminating vertically you must have at

least 10’ of vertical pipe.

The restrictor must be in the closed position

above 10' vertical vent length.

Always maintain a minimum of 1” clearance from

all sides of the vent system to any combustible

material.

A listed fire stop is required at any floor

penetration. The opening must be framed in

according to the venting manufacturer’s

instructions.

Steep roofs, nearby trees, or predominantly

strong windy conditions can promote poor draft

or down draft conditions. In this event, an

increase to the height of the vent may improve

performance.

A maximum of two 90⁰ or four 45⁰ elbows may

be used in vertical terminations. Whenever

possible use 45⁰ elbows instead of 90⁰ elbows

as they offer less restriction to the flue gases.

Vertical terminations may require additional

restriction in order to perform as intended.

Please refer to Figures 22 - 24 to adjust your

vent restrictor accordingly

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

19

All termination caps must be no less than 18”

(457mm) horizontally from any roof or vertical

surface. See Figure 18.

The termination must fall within the chart in

Figure 24.

The maximum vertical run is 35’

The minimum vent/air intake termination clearances

above the high side of an angled roof are as follows:

Roof Pitch

Feet

Meters

Flat to 6/12

1

0.3

7/12 to 9/12

2

0.6

10/12 to 12/12

4

1.2

13/12 to 16/12

6

1.8

17/12 to 21/12

8

2.4

Figure 17 - Termination Cap clearances

Prefabricated & Fireplace Chimney

Installations

The Bristol 8762 is approved for use with direct vent

chimney conversion kits in masonry or prefabricated

solid fuel listed chimneys. The following installation

requirements must be followed:

The termination must fall within the chart shown

in Figure 24.

In a masonry chimney, a fireclay liner or listed

steel liner, must be present the entire length of

the chimney.

The maximum vertical length of vent is 35’.

The liner must have an inside dimension or

diameter 6” or greater.

Prefabricated chimneys must be UL103 or ULC

S-629 listed and have a minimum INSIDE

diameter of 6”. Prefabricated chimneys must be

listed for the specific manufacturer’s conversion

kit.

The use of an existing chimney as an air intake is

not listed under the ANSI Z21.88-09-CSA 2.33-09

test methods; this installation has been tested and

approved by Intertek Testing Services with an

appropriate test. The code authority having

jurisdiction must be consulted prior to proceeding

with this installation method. See examples below.

Figure 18 – Existing Chimney Venting Options

Hearthstone Quality Home Heating Products, Inc. Bristol DX Model 8762

20

Horizontal Termination

The termination must fall within the area shown

in Figures 18 & 20.

A minimum of 36" rise is required either directly

off the heater or with the use of a minimum of a

36” snorkel.

Use a vinyl siding Stand-Off when installing

against vinyl siding. The termination cap must

not be recessed into the wall or siding. Do not fill

air spaces with any type of insulation material.

A minimum 10” x10” square hole is necessary

for proper pipe clearance through a wall,

provided the vent is positioned to maintain 2”

minimum clearance at the top. A 1” minimum

clearance must be maintained to combustible

materials around the other sides.

All horizontal terminations must also comply with

the clearance specifications to adjacent

structures outlined in Figures 18 and 20.

Horizontal sections require a 1/4" rise every 12"

of horizontal run.

NOTE: For each 90

0

elbow after 2, remove 5' from

the allowable horizontal run. For Canadian

installations: remove 4' from the allowable

horizontal run.

At the minimum vertical rise of 36”, maximum

horizontal run is 3’. (If a 36” snorkel termination

is used a maximum horizontal run of 3’ is also

applicable.)

WARNING: FAILURE TO USE ONLY PARTS

SPECIFICALLY APPROVED FOR USE WITH THIS

APPLIANCE MAY RESULT IN PROPERTY

DAMAGE OR PERSONAL INJURY.

La page est en cours de chargement...

HearthStone Bristol DX Le manuel du propriétaire

Ce manuel convient également à

HearthStone Bristol DX Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents