Harman Stove Company FireLuxe Manuel utilisateur

Marque: Harman Stove Company

Modèle: FireLuxe

Catégorie: Poêles

Taper: Manuel utilisateur

Ce manuel convient également à

FireLuxe Direct Vent Gas Stove With Top Cooking Burner System

Installation & Operating Manual

The Harman FireLuxe Direct Vent Gas Stove

With Top Cooking Burner System

WARNING: If the information in these in-

structions is not followed exactly, a fire or

explosion may result causing property dam-

age, personal injury or loss of life.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas sup-

plier’s instructions.

• If you cannot reach your gas supplier, call

the fire department.

- Installation and service must be performed by

a qualified installer, service agency or the gas

supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

This appliance may be installed in an after-

market, permanently located manufactured

home (USA only) or in a mobile home, where

not prohibited by local codes.

This appliance is for use only with the type of

gas indicated on the rating plate. This appli-

ance is not convertible for use with other

gases, unless a certified conversion kit is used.

Ce manual est disponsible en Français sur demande.

- Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of this

or any other appliance.

Report # 135-S-15-5

AVERTISSEMENT: Assurez-vous de bien suivre

les instructions données dans cette notice pour

réduire au minimum le risque d’incindie ou

d’explosion ou pour éviter tout dommage

matériel, toute blessure ou la mort.

- Ne pas entreposer ni utilizer d’essence ni

d’autres vapeurs ou liquides inflammables dans

le voisinage de cet appareil ou de tout autre

appareil.

- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE

GAZ:

•

Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas

vous servir des téléphones se trouvant

dans le bâtiment où vous trouvez.

• Appelez immédiatement votre

fournisseur de gaz depuis un voisin.

Suivezles instructions du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur

de gaz, appelez le service des incindie.

- L’installation et l’entretien doivent être assurés

par un installateur ou un service d’entretien

qualifié ou par le fournisseur de gaz.

Cet appareil peut être installé dans une maison

préfabriquée (mobile) déjà installée à demeure

si kes règlements locaux le permettent.

Cet appareil doit être uniquement avec las type

de gaz indiqué sur la plaque signalétique. Cet

appareil ne peut être converti à d’autres gaz,

sauf si une trousse de conversion est utilisée.

Ne pas utiliser cet appareils’il a été plongé,

meme partiellement, dans l’eau. Appeler un

technician qualifié pour inspecter l’appareail et

remplacer toute partie du système de commande

et toute commande qui a été plongée dans /’eau.

Attention. Au moment de l’entretien des com-

mandes, étiquetez tous les fils avant de les dé-

brancher. Des erreurs de la câblage peuvent en-

traîner un fonctionnement inadequate et dan-

gereux.

S’assurer que l’appareil fonctionne adéquate-

ment une fois l’entretien terminé.

AVERTISSEMENT. Ne pas utiliser l’appareil

si le panneau frontal en verre n’est pas en place,

est craqué ou brisé. Confiez le remplacement du

panneau à un technician agree.

INSTALLATEUR: Laissez cette notice avec l’appareil.

COMSOMMATEUR: Conservez cette notice pour consultation ultérieur.

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION 4

SPECIFICATIONS 5

INSTALLATION 6

MASSACHUSETTS REQUIREMENTS 7

VENTING 8

ASSEMBLY 14

LIGHTING AND OPERATION 23

REMOTE CONTROL HANDSET OPERATION & PROGRAMMING 26

MAINTENANCE 28

PARTS LIST 30

WARRANTY 31

IMPORTANT SAFETY INFORMATION

The installation must conform with local codes or, in the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1 or the Canadian Installation Code, CAN/CGA B149.

A manufactured home (USA only) or mobile home OEM installation must conform with the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280 or when such a standard is not applica-

ble, the Standard for Manufactured Home Installations, ANSI/BCSBCS A225.1, or Standard for Gas

Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4.

The appliance and its appliance main gas valve must be disconnected from the gas supply piping system

during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa).

The appliance must be isolated from the gas supply piping system by closing its equipment shutoff valve

during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.5

kPa).

The installation must provide for adequate ventilation air to the appliance.

This gas appliance must not be connected to a chimney flue serving a separate solid-fuel burning appliance.

The appliance, when installed, must be electrically grounded in accordance with local codes, or, in the

absence of local codes, with the National Electrical Code ANSI/NFPA 70, or the Canadian Electrical Code,

CSA C22. 1.

When the appliance is installed directly on carpeting or non-ceramic tile or other combustible material other

than wood flooring, the appliance shall be installed on a metal or wood panel extending the full width and

depth of the appliance. A commercially available hearth pad meets this requirement.

The appliance area must be kept clear and free from combustible materials, gasoline and other flammable

vapors and liquids.

The flow of combustion and ventilation air must not be obstructed.

Do not use this appliance if any part has been under water. Immediately call a qualifed service technician

to inspect the appliance and to replace any part of the control system and any gas control which has been

under water.

Due to high temperatures, the appliance should be located out of traffic and away from furniture and

draperies.

Children and adults should be alerted to the hazards of high surface temperatures and should stay away to

avoid burns or clothing ignition.

Young children should be carefully supervised when they are in the same room as the appliance.

Clothing or other flammable material should not be placed on or near the appliance.

Any screen or guard removed for servicing an appliance must be replaced prior to operating the appliance.

Installation and repair should be done by a qualified service person. The appliance should be inspected

before use and at least annually by a professional service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. It is imperative that the control compartments,

burners and circulating air passageways of the appliance be kept clean.

WARNING: Do not operate the appliance with the glass front removed, cracked or broken.

Replacement of the glass should be done by a qualified service person.

WARNING: Use only replacement glass, part number 3-40-21001500 and glass gasket, part number

3-44-00539. Do not use substitute materials. Do not strike or slam the glass front. Do

not use abrasive cleaners. Do not clean when hot.

SPECIFICATIONS

MAIN BURNER Natural Gas Propane (LP)

Input Rating-Btu/hr 36000 36000

Min. Input-Btu/hr 23000 23000

Orifice-DMS #34 #50

COOKING BURNER

Input Rating-Btu/hr 12000 12000

Min. Input-Btu/hr 3500 3500

Orifice-DMS #52 #58

GAS SUPPLY

Manifold Pressure 4.5”w.c./1.3kPa 10.0”w.c./2.5kPa

Min. Supply Pressure 5.0”w.c./1.3kPa 11.0”w.c./2.8kPa

Max. Supply Pressure 10.0”w.c./1.8kPa 13.0”w.c./3.3kPa

Annual Fuel Utilization Efficiency (AFUE) 72.7% 74.9%

Steady State Efficiency 73.4% 75.6%

It is recommended that the pilot flame be turned off if the appliance will not be in use for an

extended period of time.

This appliance is equipped for use with the fuel type indicated on the rating plate. Fuel conversion kits that

include the necessary parts and instructions are available from your installer, dealer or Harman Stove Co.

This appliance has been certified by OMNI-Test Laboratories, Inc. to ANSI Z21.88-2005 • CSA 2.33-2005

Vented Gas Fireplace Heaters and CAN1-2.17-M91, Gas-Fired Appliances for Use At High Altitudes.

The FireLuxe is approved for installation at elevations up to 2000 feet in the U.S. and 1370 meters (4500

feet) in Canada without change. If your installation is at an elevation greater than these, consult with the

local authority having jurisdiction for gas product installations to determine their specific requirements for

high altitude installations.

28” (71cm)

23 1/4” (59cm)

30 1/2” (77.5cm)

20 1/2”” (52cm)

INSTALLATION

MINIMUM CLEARANCES TO COMBUSTIBLE CONSTRUCTION

Stove to Left Side Wall 6” (150mm) Stove to Corner Wall 6” (150mm)

Stove to Right Side Wall 6” (150mm) Stove to Ceiling 30” (760mm)

Stove to Rear Wall 6” (150mm) Stove to 10” Deep Mantel 30” (760mm)

Max. Alcove Depth 24” (610mm)

Several issues must be addressed when selecting a suitable location for your FireLuxe. The minimum

clearances to combustible construction are listed below. In addition, access to the gas supply and electrical

supply must be considered. The location of the stove will also affect the venting requirements and you

must be certain the location will allow compliance with the venting requirements shown on pages 8 – 13.

You must also insure that your installation provides adequate accessibility clearance for servicing and

proper operation.

When the appliance is installed directly on carpeting or tile or other combustible material other than wood

flooring, the appliance shall be installed on a metal or wood panel extending the full width and depth of the

appliance.

Installation and repair should be done by a qualified service person. The appliance should be inspected

before use and at least annually by a professional service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. It is imperative that the control compartments,

burners and circulating air passageways of the appliance be kept clean.

CEILING MANTEL

CORNER

WALLS

A = 6” (150mm)

B = 6” (150mm)

C = 6” (150mm)

D = 24” (610mm) Max. Alcove Depth

E = 6” (150mm)

F = 30” (760mm)

G = 30” (760mm)

H = 10” (250mm) Max.

INSTALLATION

The gas stove is shipped with a flexible connector that has a 1/2” NPT female connection. The gas supply

piping should have a separate gas shutoff valve and a 1/8” NPT plugged tapping upstream of the valve. The

stove and its main control valve must be disconnected from the gas supply piping system during any pres-

sure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa). The stove must be isolated from

the gas supply piping system by closing the main control valve during any pressure testing of the gas supply

system at test pressures equal to or less than 1/2 psi (3.5 kPa). After the gas supply has been connected,

apply a soapy water solution to all the fittings to check for gas leaks. Never use a flame to test for leaks.

REQUIREMENTS FOR THE COMMONWEALTH OF MASSACHUSETTS

This product must be installed by a licensed plumber or gas fitter when installed within the Com-

monwealth of Massachusetts. If this appliance is installed in a dwelling, building or structure used in

whole or in part for residential purposes and the installation includes a horizontal vent termination

that is less than seven (7) feet above the finished grade in the area of the venting, including but not

limited to decks and porches, a hard-wired carbon monoxide detector with an alarm and battery

back-up must be installed on the floor level of the dwelling, building or structure where the appli-

ance is to be installed.

Additionally, a hard-wired or battery operated carbon monoxide detector with an alarm must be in-

stalled on each additional level of the dwelling, building or structure served by the appliance. It shall

be the responsibility of the property owner to secure the services of qualified licensed professionals

for the installation of hard-wired carbon monoxide detectors.

In the event that the horizontally vented appliance is installed in a crawl space or attic, the hard-

wired carbon monoxide detector with alarm and battery back-up may be installed on the next adja-

cent floor level.

In the event that this requirement cannot be met at the time of completion of the installation of the

appliance, the owner shall have a period of thirty (30) days to comply with the requirement. How-

ever, during said thirty (30) day period, a battery operated carbon monoxide detector with alarm

must be installed.

Each carbon monoxide detector as required in accordance with the above provisions must comply

with NFPA 720 and be ANSI/UL 2034 and IAS certified.

In addition when the stove is horizontally vented and the vent termination is less than seven (7) feet

above finished grade a metal or plastic identification plate must be permanently mounted to the exte-

rior of the building at a minimum height of eight (8) feet above grade directly in line with the ex-

haust vent terminal. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

A COPY OF THESE INSTRUCTIONS PLUS ALL VENTING INSTRUCTIONS WHICH IN-

CLUDE PARTS LISTS, AND/OR ALL VENTING DESIGN INSTRUCTIONS MUST REMAIN

WITH THE STOVE AT THE COMPLETION OF THE INSTALLATION.

ATTENTION INSTALLERS: Mark below which venting system was used in the installation. These

instructions must remain with the FireLuxe Installation & Operation Manual.

Simpson DuraVent GS

AmeriVent Direct Security Secure Vent Selkirk DT

To avoid confusion discard the all vent manufacturers instructions that do not apply to this installation.

NOTE: If you will be installing the optional warming shelves, make sure to plan for the additional width

that they occupy. For the details, see the information included with the warming shelf kit.

VENTING

The FireLuxe Gas Stove has been tested and listed for installation with 4” X 6 5/8” Simpson DuraVent GS,

AmeriVent Direct, Security Secure Vent and Selkirk DT direct venting components. For specific installa-

tion requirements, follow the installation instructions included by the venting manufacturer with the venting

system components you have chosen. The total vent length may not exceed 40 feet, including vertical rise

and horizontal run. The vent lengths are measured from the stove, not the floor. The minimum vertical rise

required is 2 feet. The maximum allowed horizontal vent run is 20 feet when the venting includes at least 5

feet of vertical rise. The maximum allowed horizontal vent run for vertical rises of less than 5 feet is shown

in the venting charts. No more than three elbows may be used in any installation. The venting charts in-

clude the use of one elbow. For the second or third elbows that are included in the installation, add 4 feet to

the actual horizontal run for each elbow to determine the equivalent horizontal run for the installation.

The venting charts allow a simple way to determine the recommended initial settings for both the air inlet

and exhaust restrictors. These settings have been determined by extensive testing and will be a good start-

ing point while setting up the stove. Small adjustments from these settings may be needed to account for

specific installation variables. Please see the instructions on pages 21 - 22 for how to adjust the restrictors.

The letters (A-E) designate the position of the air inlet restrictor. When ½ is added to the letter designation,

this indicates that the position is halfway between adjacent letters. The numbers (0-8) indicate the position

of the exhaust restrictor. When ⅛, ¼, ⅜, ½, or ¾ is added to the number designation, this indicates that the

position is fractionally between adjacent numbers. For example, 5¼ is one-fourth the way between 5 and 6.

To use the charts, determine the horizontal run length and vertical rise length (in feet) for your installation.

If more than one elbow is used, add 4 feet to the actual horizontal run length for each additional elbow to

get the equivalent horizontal run for the chart. Note: Remember that a maximum of three elbows is al-

lowed. Select the venting chart for the fuel type (Natural Gas or Propane (LP) Gas) and find the box on the

chart that corresponds to the vertical rise and actual horizontal run (or equivalent horizontal run, if two or

three elbows are used) and read the settings for the inlet air restrictor (A-E) and exhaust restrictor (0-8).

Examples are shown below and on page 9.

The FireLuxe is shipped with a Simpson DuraVent GS starter section that is specifically designed for the

FireLuxe. Regardless of the venting brand you chose, you must use the provided DuraVent starter section.

All of the venting brands listed for use with the FireLuxe are compatible with the provided starter section.

For venting system installation details, refer to the instructions provided with the venting system you have

chosen. Each brand has specific installation requirements that must be followed to insure a safe and func-

tional venting system for your FireLuxe.

Note: The Fireluxe is shipped from the factory with restrictor settings for 2 feet of vertical rise and 1 foot

of horizontal run and for the fuel type listed on the rating plate attached to the rear of the stove.

E½

6¾

Example 1

Fuel = Propane (LP)

Vertical Rise = 15 feet

Horizontal Run = 8 feet

Elbows = 1

Equivalent Horizontal Run = 8 feet

Air Restrictor Setting = E½

Exhaust Restrictor Setting = 6¾

INLET AIR

EXHAUST

VENTING

Example 2

Fuel = Propane (LP)

Vertical Rise = 6 feet

Horizontal Run = 8 feet

Elbows = 3

Equiv. Horizontal Run = 16 feet (8+4+4)

Air Restrictor Setting = C

Exhaust Restrictor Setting = 3

EXHAUST

INLET AIR

E½

7⅜

Example 3

Fuel = Natural Gas

Vertical Rise = 22 feet

Horizontal Run = 0 feet

Elbows = 0

Equiv. Horizontal Run = 0 feet

Air Restrictor Setting = E ½

Exhaust Restrictor Setting = 7 ⅜

EXHAUST

INLET AIR

E½

6½

Example 4

Fuel = Propane (LP)

Vertical Rise = 12 feet

Horizontal Run = 4 feet

Elbows = 1

Equiv. Horizontal Run = 4

Air Restrictor Setting = E ½

Exhaust Restrictor Setting = 6 ½

EXHAUST

INLET AIR

VENTING

VERTICAL RISE IN FEET

HORIZONTAL RUN IN FEET

NATURAL GAS VENTING

IF YOUR VENTING CONFIGURA-

TION FALLS ABOVE THIS DOT-

TED LINE, SEE PAGE 12

VENTING

VERTICAL RISE IN FEET

HORIZONTAL RUN IN FEET

PROPANE (LP) GAS VENTING

IF YOUR VENTING CONFIGURA-

TION FALLS ABOVE THIS DOT-

TED LINE, SEE PAGE 12

VENTING

PLEASE NOTE: If your specific venting configuration falls in a box in the venting charts (on pages 10 &

11) that is above the dotted line ( ), you must use one of the approved direct vent venting systems

that utilizes a stainless steel

inner liner. The dotted line corresponds to a total vent length of 30 feet includ-

ing vertical rise and horizontal run. This requirement is part of the ANSI standards and is based on testing

conducted to determine where the exhaust gas temperature drops to the point where condensation might oc-

cur in the vent pipe. The standards require the use of corrosion resistant liner materials if that specific total

vent length is exceeded.

VENTING INTO AN EXISTING MASONRY OR CLASS A CHIMNEY

The FireLuxe has been tested and found to be in compliance when using an existing chimney as the air con-

duit for the direct venting system. This type of installation is used when replacing an existing wood-

burning stove with a FireLuxe direct vent gas stove. Check with the venting manufacturer to see if they

have the needed components or kits for this type of installation. Also, check the vent manufacturer’s instal-

lation instructions for the specific details and requirements for this type of installation. The chimney must

be in good condition with no cracks or leaks for this type of installation and the venting components must

be sealed where they meet the existing chimney. Also, check with the local authority having jurisdiction to

see if this type of installation is allowed in your area.

RESERVED FOR FUTURE VENTING CONFIGURATION INFORMATION

VENT TERMINAL CLEARANCES

VENTING

Venting terminals shall not be recessed into a wall or siding.

ASSEMBLY

UNPACKING AND PLACING THE FIRELUXE

By now, you will have removed the shipping carton from the base pallet. The FireLuxe is shipped on spe-

cially designed shipping supports that keep the weight of the stove off the legs to avoid damaging them dur-

ing transit. Cut the strapping that secures the stove to the pallet. The stove must be lifted straight up to dis-

engage it from the shipping brackets. The best place to lift is at the base of the stove sides. The stove top

and front have to be removed in order to unpack and install the logs and top cooking burner parts. Remov-

ing them now will reduce the weight and make it easier to lift the stove. Also, locate the ashlip and ashlip

mounting hardware and set aside in a safe location. It will be installed later.

First, remove the cast iron stove top. This is accomplished by simply lifting up on the top as it is a gravity

fit. The top is heavy and extra care should be taken when handling it, especially if the stove is enameled.

Set the top aside on a padded surface. A carpeted floor is a good choice.

Remove the top cooking grill and the cooking burner cover plate and set aside for now. They are packed in

bubble wrap or foam packing and are located on the now exposed top of the stove’s firebox.

Remove the stove front by lifting it straight up to disengage the tabs that secure it to the sides. Once it is

disengaged, you can move the front away from the stove body. Note: The front doors may have a tendency

to swing open while you are handling the front. Placing a small piece of masking tape around the two doors

where they meet at the center will keep the doors from moving. Set the front aside with the back side down

taking extra care if it is enameled.

With these parts removed and set aside, lift the stove up and off the pallet and set it near to its installation

position. Like any cast iron stove, it is best to pick the stove up while adjusting its position rather than

dragging it on its legs. This reduces the chances of damaging a leg or chipping enamel or of damaging the

hearth surface. This is the best time to install the optional blower kit if being used. See the instructions in-

cluded with the blower kit.

The legs have leveling screws that will allow you to compensate for irregularities on the surface under the

stove. Using as little adjustment as possible for each leveling screw, adjust them as needed to get the stove

as level as possible both side to side and front to back. This is important since the FireLuxe includes a top

cooking burner and having the stove level will reduce the likelihood of spillage while cooking.

The FireLuxe is shipped set up for the fuel type indicated on the rating plate attached to the rear of the

stove. Note: If you need to switch fuels, please see the instructions included with the appropriate fuel con-

version kit. The logs are shipped in protective material inside the firebox and do need to be unpacked and

installed on the burner.

With the stove top and front removed and safely set aside

during the unpacking process, unlatch each of the three

glass frame latches by pulling forward on the latch finger

tabs while lifting up. See the adjacent illustration. This

will allow the glass frame to tip slightly forward. The glass

is loose in the frame, held in place only by friction from

the gasket so it is very important to support both the glass

and the frame when handling. Place your thumbs on the

outside of the glass frame and wrap your fingers around

the frame and onto the glass. Squeeze the frame and glass

while moving. Carefully lift the glass frame and glass up

and off the stove. Set the glass and frame aside on a pad-

ded surface. The outside of the frame should be facing

down so the glass will stay in place.

UNLATCHING DETAIL-

PULL FORWARD AND

UP TO UNHOOK LATCH

FROM GLASS FRAME

ASSEMBLY

LEFT REAR LOG

RIGHT REAR LOG

LEFT REAR LOG RECESS

RIGHT REAR LOG RECESSES

LEFT FRONT LOG RECESS

RIGHT FRONT LOG RECESS

PINS

LOGS AND EMBERS

Slide the logs and packing out of the firebox and set on the floor. Carefully unpack each of the four logs

and three loose ember pieces. The logs and embers are somewhat fragile and will not survive being

dropped from any significant height.

Remove the protective cover material from the top of the burner.

Each of the four logs is unique and must be placed in a precise location on top of the burner. The burner

and log system is designed to facilitate correct placement of the logs. Flat recessed areas on the burner top

are keyed to each of the four main logs. The rear logs also have locating pins with corresponding sockets in

the logs. The following illustration highlights these features.

Place the left rear log first. There is recessed area in the burner top as well as a locating pin in and a cor-

responding socket in the log. Line-up the socket over the pin and place the log in the recess.

Place the right rear log next. There is a recessed area on the top of the burner that corresponds to the shape

of the base of the log. Simply place the log in the recess. The following illustration shows the proper posi-

tions for the two rear logs.

ASSEMBLY

Place the left front log next. Again, there is a recess on the burner top that corresponds to the shape of the

flat base of the log. Place the left end of the log in the recess and rest the right end on the left rear log using

the illustration below as a guide. Place the right front log last. Again, place the flat base of the log in the

corresponding recess in the burner top per the illustration below.

LEFT FRONT LOG

RIGHT FRONT LOG

There are three loose ember pieces. Each ember piece has a specific location on the burner. Refer to the

illustration below to get the proper placement and orientation for each ember piece. If you look carefully,

you will see that each ember has features that will help you in placement relative to the burner surface and

the logs.

EMBER 1

EMBER 2

EMBER 3

ASSEMBLY

When correctly placed, the logs and embers will look like the illustration below.

LATCHING DETAIL-

PULL FORWARD AND

DOWN TO HOOK LATCH

OVER GLASS FRAME

After the logs and embers have been placed, the next

step is to replace the glass panel and frame. Carefully

pick up the glass and glass frame assembly by grasp-

ing the sides of the frame and using your thumbs and

fingers to hold the glass in place within the gasket and

frame.

With the glass frame (and glass) at a slight angle

(leaving room for your fingers between the frame and

the firebox) insert the bottom edge of the frame into

the frame retainer located on the bottom front of the

firebox. Take care to center the frame from left to

right. Once the bottom edge is in place, move your

fingers out of the way and press the top of the frame

against the firebox while pushing down to be sure the

frame is fully engaged in the frame retainer. Hold the

frame in place with one hand and engage the three

glass frame latches by pulling out and down while

hooking them over the frame.

Top or Rear Vent

The FireLuxe has provisions for either top or rear venting but is shipped from the factory set-up for top

venting. The rear position is sealed with a special cover plate. If your installation requires rear-venting,

you will need to reverse the positions of the starter section and the cover plate.

Remove the four screws that secure the vent starter section flange to the stove and remove the starter.

There are two ceramic fiber gaskets that seal the starter to the stove. These gaskets are very important!

Take care in handling these gaskets as they are somewhat fragile and will tear. Remove the vent cover plate

from the rear of the stove following the same procedure as the starter. Install the cover plate on the top vent

opening.

ASSEMBLY

It is now time to install the ashlip on the stove front and to install the stove front and stove top.

The ashlip is secured to the front using two brackets and four 1/4 – 20 hex head bolts. With the front facing

down on a padded surface, align the mounting bosses on the ashlip with the mounting bosses on the front.

Install the two “L”-shaped brackets with the slotted end on the ashlip. Tighten the bolts to the front but

leave the bolts to the ashlip finger tight. Carefully turn the front over. Adjust the ashlip so that it is tight

against the lower

molding on the front.

Tighten the ashlip

bolts. Take care with

an enamel stove to

prevent chipping.

Replace the stove

front by aligning the

outer edges with the

stove sides while the front is about ½ to 1” above its final position. This is to allow the sheet metal tabs that

secure it to the sides to be above the mating cast iron tabs on the sides. Carefully push the front in while

allowing it to slide down. All four tabs (two top and two bottom) should engage with the sides. Once the

front has reached the proper position, check the vertical alignment by looking at the alignment of the edges

of the front to the casting details on the side. They should be parallel. If they are not, simply push or pull

on the front until a good visual alignment is obtained. Take extra care with this procedure if your stove is

enameled. Just move in small increments as you line up the tabs and lower the front into place. If you take

your time, you will avoid chipping. Remove any

masking tape used to secure the doors.

Be sure that the inner and outer gaskets are in

their proper positions. Install and tighten the

four screws. Finally, install the vent starter

section in the rear vent position. Again,

make sure that the inner and outer gaskets are

in their proper positions and install and

tighten the four screws.

INNER

GASKETS

OUTER

GASKETS

STARTER SECTION

COVER

PLATE

Next, install the brass diffuser ring and top burner

cover on the cooking burner. This is a small round

disk that sits on top of the brass diffuser ring on the

top burner. If you look at the back side of the diffuser,

you will see alignment tabs. They correspond to

alignment locations on the burner. The cover is sim-

ply centered in the diffuser.

BRASS DIFFUSER RING

BURNER COVER

At this time, you will also want to install the

optional cast iron plate that fills in the top vent

cutout on the stove top. With the bottom of

the top facing up, place the filler plate in the

cutout with the filler plate edge molding

aligned with the edge molding on the top. Us-

ing the bracket and three fasteners included

with the filler plate kit, secure the filler plate

to the top. See the illustration included with

the optional filler plate kit for more informa-

tion.

ASHLIP

SLOT

BRACKET

FRONT

ASSEMBLY

The remote control handset is powered by a 9-volt battery.

There is a low battery indicator on the handset display panel.

To replace the battery, remove the access cover from the rear of

the handset and unsnap the old battery. Replace with a high

quality long-life alkaline battery and reinstall the cover.

BATTERY INSTALLATION OR REPLACEMENT

The batteries used to power the burner control systems on the FireLuxe should last a full season or more

with normal use. Battery life for the main burner control system will be reduced if you are manually modu-

lating the flame up and down on a frequent basis.

There are three battery locations.

The electronic ignition module for the cooking burner is located behind an access panel located on the right

rear of the stove (when looking from the stove front). A single fastener secures the panel. Simply remove

fastener and the panel to access the single 9-volt battery. Unsnap the old battery from the module and re-

place with a fresh one. Use a high quality long-life alkaline battery. Replace the access panel and fastener.

Refer to the illustrations below.

ACCESS COVER

FASTENER

9V BATTERY

Next, reinstall the top. This is a gravity fit. Carefully align the inner edge of the top with the outer edges of

the sides and front. Lower the top down into place. Check to see if it is level and push down as needed to

get the proper alignment relative to the aesthetic details on the front and sides.

Finally, install the top cooking grate. This simply sits over the burner. A raised border on the stove top de-

fines the cooking grate position.

ASSEMBLY

The main heating valve battery pack is located at the center rear of the stove. A removable valve access

panel covers the valve components and simply lifts up and off the stove back. The batteries are located in

the control module next to the actual valve. The battery access cover lifts and slides off to expose the four

AA batteries. Note the orientation of each battery as you replace the old with new as this is critical to the

operation of the control. Use only high quality long-life alkaline batteries. Replace the battery cover and

the valve access panel. Refer to illustrations below.

NOTE: The control module is secured to the valve bracket with hook-and-eye strips and can be pulled

away from the bracket if necessary to gain better access to the battery cover and compartment. Be certain

not to dislodge the wiring from the control module and be sure to place the module back it its original posi-

tion after the batteries and cover are installed.

CONTROL MODULE

COVER

AA BATTERIES

VALVE ACCESS

PANEL

CONTROL MODULE

VALVE

GAS CONNECTION

The FireLuxe is shipped from the factory with a flexible gas connector that has a 1/2” NPT female connec-

tion. The gas supply piping should have a separate gas shut-off valve and a 1/8” NPT plugged tapping up-

stream of the valve. The FireLuxe and its inlet regulator. Main burner valve and cooking burner valve must

be disconnected from the gas supply piping system during any pressure testing of that system at test pres-

sures in excess of 1/2 psi (3.5kPa). The FireLuxe must be isolated from the gas supply piping system by

closing the main control valve during any pressure testing of the gas supply system at test pressures equal to

or less than 1/2 psi (3.5kPa). After the gas supply has been connected, apply a soapy water solution to all

the fittings to check for gas leaks. Never use a flame to test for leaks.

La page charge ...

Harman Stove Company FireLuxe Manuel utilisateur

Marque: Harman Stove Company

Modèle: FireLuxe

Catégorie: Poêles

Taper: Manuel utilisateur

Ce manuel convient également à

FireLuxe Direct Vent Gas Stove With Top Cooking Burner System

Télécharger le PDF

rapport

dans d''autres langues

English: Harman Stove Company FireLuxe User manual

Harman Stove Company FireLuxe Manuel utilisateur

Ce manuel convient également à

Harman Stove Company FireLuxe Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents