Jøtul GF 370 DV Installation And Operation Instructions Manual

Marque: Jøtul

Modèle: GF 370 DV

Catégorie: Poêles

Taper: Installation And Operation Instructions Manual

Jøtul GF 370 DV

Direct Vent Gas Stove

Installation and

Operation Instructions

– Do not store or use gasoline or other

flammable vapors and liquids in the vicinity

of this or any other appliance.

– WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the fire department.

– Installation and service must be performed

by a qualified installer, service agency or the

gas supplier.

– In the Commonwealth of Massachusetts,

a carbon monoxide (CO) detector shall be

installed in the same room as the appliance.

WARNING: If the information in these

instructions is not followed exactly, a fire

or explosion may result causing property

damage, personal injury or loss of life.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

– QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE

GAZ:

• Ne pas tenter d’allumer l’appareil.

• Ne touchez à aucum interrupteur. Ne

pas vous servir des téléphones se trou-

vant dans le bâtiment où vous trouvez.

• Appelez immédiatement votre fournis-

seur de gaz depuis un voisin. Suivez les

instructions du fournisseur.

• Si vou ne pouvez rejoindre le fournis-

seur de gaz, appelez le service des incend-

ies.

– L’installatione l’entretien doivent être

assurés par un installateur ou un service

d’entretien qualifié ou par le fournisseur

de gaz.

– Ne pas entreposer ni utiliser d’essence ni

d’autres vapeurs ou liquides inflammables

dans le voisinage de cet appareil ou de tout

autre appareil.

AVERTISSEMENT: Assurez-vous de bien suiv-

reles instructions données dans cette notice

pour réduire auninimum le risque d’incendie

ou d’explosion ou pour éviter tout dommage

matériel, toute blessure ou la mort.

ATTENTION : CES INSTRUCTIONS DOIVENT

DEMUERER AVEC LE PROPRIÉTERE D’UNE

MAISON.

This appliance may be installed in an aftermarket,

permanently located, manufactured home or mobile

home, where not prohibited by local codes.

This appliance is only for use with the types of gas

indicated on the rating plate. A conversion kit is

supplied with the appliance.

138914 Rev. K / 7.27.10

Suggested Tools for

Installation and Service

• External regulator (for Propane only)

• Piping which complies with local code

• Manual shut-off valve -

T-Handle required in Massachusetts

• Sediment trap - if required by code

• Tee joint

• Pipe wrench

• Pipe sealant

• 10 mm open end wrench

• 1/2”, 7/16” open end wrench

• Phillips head screwdriver

• Flat head screwdriver

• 1/4” nut driver

• Gloves

• Safety glasses

• Torx T-20 screwdriver

THIS OWNER’S MANUAL PROVIDES INFORMATION TO

ENSURE SAFE INSTALLATION AND EFFICIENT, DEPENDABLE

OPERATION OF YOUR FIREPLACE INSERT. PLEASE READ

THESE INSTRUCTIONS IN THEIR ENTIRETY AND MAKE THEM

AVAILABLE TO ANYONE USING OR SERVICING THIS GAS

INSERT.

DO NOT ATTEMPT TO ALTER OR MODIFY THE CONSTRUCTION

OF THIS APPLIANCE OR ITS COMPONENTS. ANY

MODIFICATION OR ALTERATION WILL VOID THE WARRANTY,

CERTIFICATION AND LISTING OF THIS APPLIANCE.

�

We recommend that

our gas products be

installed and serviced by

professionals who are

certified in the U.S. by

the National Fireplace

Institute® (NFI) as NFI Gas

Specialists.

THIS PRODUCT MUST BE INSTALLED BY

A LICENSED MASTER OR JOURNEYMAN

PLUMBER OR GAS-FITTER WHEN

INSTALLED IN THE COMMONWEALTH OF

MASSACHUSETTS.

Your fireplace insert has a unique serial number

stamped on the rating plate which is located in the valve

compartment. Please record the serial number in the

space below. You may also wish to attach your purchase

receipt to this page for future reference.

MODEL NAME: Jøtul GI 450 DV II Katahdin Gas Fireplace

SERIAL NUMBER:_______________________________

DATE OF PURCHASE:____________________________

AUTHORIZED DEALER:__________________________

ADDRESS ___________________________________

PHONE: ____________________________________

INSTALLER:__________________________________

FUEL TYPE:____________________________________

FUEL CONVERSION: NO _______ YES_____

NOTES:________________________________________

______________________________________________

66.07%

















Jøtul GF 370 DV

138914 Rev. K / 7.27.10

Table of Contents

Installation & Service Tools ..................2

Specifications .................................................. 4

General Information .......................................5

Safety Information ........................................ 6

Installation

Hearth Requirements .........................7

Clearances ...............................................7

Vent Requirements

Approved Vent Manufacturers ......... 8

Vertical Termination ............................ 8

Masonry Chimney Conversion .......... 9

Horizontal Termination .....................10

Vent Termination Clearances ............11

Vent Restriction Adjustments .......... 12

Vent Termination Diagram ............... 13

Stove Assembly

1. Glass Frame Removal ..................14

2. Routing the Power Supply .........14

3. Gas Connection ..............................14

4. Gas Pressure ................................... 15

5. Fuel Conversion .............................16

6. High Altitude Adjustment ..........18

7. Skamol Panel Installation ...........19

8. Reflective Panel Installation .......19

9. Wishing Rock Installation ...........19

10. Starfire Glass Installation ...........19

11. Log Set Installation .....................20

12. Outer Decorative Glass Panels .. 21

13. System Check ............................... 22

14. Flame Picture Adjustment ..........23

Operation

System Overview ............................... 24

Control Functions ................................25

Wiring Diagrams ................................ 28

Maintenance

Annual Cleaning .................................30

Glass Replacement ............................30

Battery Replacement ......................... 31

Accent Lamp Replacement .............. 31

Illustrated Replacement Parts ........... 32 - 35

Appendix

Mobile Home Installation ................ 36

Correct Optional Flame Pictures ... 36

Waranty Statement ..................................... 39

Lighting Instructions ................................. 39

Unpacking the Stove

1. Before beginning the installation, inspect the stove

for shipping damage and immediately report any

evidence of damage to your dealer.

2. Confirm stove contents.

The Jøtul GF 370 DV includes the following loose

items shipped in the Miscellaneous Hardware bag;

• 4 mm hex key - used to remove the

front glass panel for access to the firebox.

• Remote Control Transmitter

• Extension Power Cord

• M6 x 12 mm hex bolts, 4 - used with

Outer Decorative Glass Panels.

• Propane Fuel Conversion Kit 156800

3. Confirm Firebox Components.

The firebox accessories have been packed in

separate boxes, and will include one or more of the

following items:

• Traditional Log Set 156789

• Starfire Glass 156815

• Wishing Rocks 156814

• Skamol Panels 156816

• Reflective Glass Panels 156817

4. Remove Pallet Screw. See fig. 1.

Figure 1.

Pallet screw location

138914 Rev. K / 7.27.10

Specifications

Input Rates

Natural Gas

28,000 BTU/hr. maximum input

18,173 BTU/hr. minimum input

Propane

24,000 BTU/hr. maximum input

20,750 BTU/hr. minimum input

Inlet Pressure: MIN MAX

Natural Gas: 5.0 WC (1.24 kPa) 7.0 WC (1.74 kPa)

Propane: 11.0 WC (2.74 kPa) 13.0 WC (3.24 kPa)

Manifold Pressure: MIN MAX

Natural Gas: 1.6 WC (.398 kPa) 3.5 WC (0.87 kPa)

Propane: 6.4 WC (1.59 kPa) 10.0 WC (2.48 kPa)

• Steady State Efficiency: 74.7% NG / 79.3% LP

• AFUE Efficiency: 71.2% NG / 75.6% LP

• CSA P4. 1-02 Fireplace Efficiency: 66.70 %

• Intermittent Pilot Ignition ( IPI )

• Continuous Pilot Ignition Mode ( CPI or “standing

pilot”) is available.

• Power Requirement: 120 VAC for Fan, Lamp, and

Burner Control Module

• Remote Control Transmitter batteries preinstalled,

3, AAA - 1.5 v

• Remote Control Receiver batteries supplied: 4, AA

• Fan Control Module: 120V / 60 Hz

Jøtul GF 370 DV

Direct Vent Gas Stove

Manufactured and Distributed by:

Jøtul North America

Gorham, Maine USA

Jøtul AS

Fredrikstad, Norway

Test Standards

This appliance complies with

National Safety standards and is

tested and listed by Intertek Testing

Services of Middleton, Wisconsin.

In addition, the Jøtul GF 370

DV has been tested and listed as a

direct vent gas fireplace heater and listed to

ANSI Z21.88-2005, ANSI z21.88a/CSA 2.33a-2007,

CAN/CGA 2.17-M91.

Traditional Log Set ................................................ #156789

Wishing Rocks Set .................................................#156814

Starfire Glass Kit .................................................... #156815

Reflective Glass Firebox Liner ............................. #156817

Decorative Outer Glass Panel Kit .................... #350995

Fuel Conversion Kit, Propane - 33% TD ............ #156800

Fuel Conversion Kit, Natural Gas - 33% TD .......#156801

High Altitude Adjustment Kit, NG .................... #156822

Accessories

















Figure 2. Overall dimensions

138914 Rev. K / 7.27.10

and legal installation. Some areas require a permit

to install a gas burning appliance. Always consult

your local building inspector or authority having

jurisdiction to determine what regulations apply in

your area.

In the absence of local codes, the installation re-

quirements must comply with the current National

codes. In the U.S., these requirements are estab-

lished in the National Fuel Code, ANSI Z223.1.(NFPA

54). In Canada, the codes have been established in

CAN/CGA B149 Fuel Installation Code.

Installer l’appareil selon les codes ou reglements

locaux, ou, en l’absence de tels reglements, selon

les Codes d’installation CAN/CGA-B149.

5. Do not operate this fireplace if any part of it has

been under water..

Immediately call a qualified service technician to

inspect the heater and to replace any part of the

control system and any gas control which has been

under water.

Ne pas se servir de cet appareil s’il a ete’ plonge

dans l’eau, completement ou en partie. Appeler

un technicien qualifie pour inspecter l’appareil et

remplacer toute partie du syste’me de controle et

toute commande qui ont ete plonges dans l’eau.

6. Do not operate the fireplace with the glass front

removed, cracked or broken. Replacement of the

glass should be done by a licensed or qualified ser-

vice person. Only remove glass for routine service.

Always handle glass carefully.

Pour utilisation avec les portes en verre cerifiers

aved l’appareil seulemend ou. Ne pas utiliser avec

des portes on verre.

7. Notify your insurance company before proceding

with installation of this fireplace.

General Information

IMPORTANT: SAVE THESE INSTRUCTIONS.

1. The installation and repair of this appliance must

be done by a qualified service person. Failure to

properly install and maintain this heater could re-

sult in an unsafe or hazardous installation, which

may result in a fire, explosion, property damage,

personal injury or loss of life.

2. This appliance should be inspected before use and

at least annually. More frequent cleaning may

be required due to excessive lint from carpeting,

bedding material, etc. It is imperative that control

compartments, burners and circulating air pas-

sageways of the appliance be kept clean.

`S’assurer que le bruleur et le compartiment des

commandes sont propres. Voir les instructions

d’installation et d’utilisation qui accompagnent

l’appareil.

3. This appliance may be installed in an aftermar-

ket permanently located, manufactured (mobile)

home, where not prohibited by local codes.

This appliance is only for use with the type(s) of

gas indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a

certified kit is used.

Cetappareil peut être installé dans un maison

préfabriquée (mobile) déjà installée à demeure si

les règlements locaux le permettent.

Cet appareil doit être utilisé uniquement avec les

types de gas indiqués sur la plaque signalétique.

Ne pas l’utiliser avec d’autres gas sauf si un kitde

conversion certifié est installé.

4. The installation must conform to local codes. Your

local Jøtul authorized dealer can assist you in de-

termining what is required in your area for a safe

THIS HEATER MUST BE INSTALLED AND MAIN-

TAINED BY A QUALIFIED SERVICE AGENCY.

DO NOT ATTEMPT TO ALTER OR MODIFY THE

CONSTRUCTION OF THIS APPLIANCE OR ITS COM-

PONENTS. ANY MODIFICATION OR ALTERATION

WILL VOID THE WARRANTY, CERTIFICATION AND

LISTING OF THIS APPLIANCE.

WARNING: FAILURE TO POSITION THE PARTS IN

ACCORDANCE WITH THE DIAGRAMS HEREIN OR

FAILURE TO USE ONLY PARTS SPECIFICALLY AP-

PROVED WITH THIS APPLIANCE MAY RESULT IN

PROPERTY DAMAGE OR PERSONAL INJURY.

138914 Rev. K / 7.27.10

Safety Information

Due to the high operating temperatures this

appliance should be located out of traffic and

away from furniture, draperies, etc. Maintain

proper clearance to combustible mantels and

fireplace trim.

Children and adults should be alerted to the

hazards of high surface temperatures and should

stay away to avoid burns or clothing ignition.

Young children should be supervised while they

are in the same room as the appliance. Toddlers,

young children and others may be susceptible

to accidental contact burns. A physical barrier,

such as a child guard, is recommended to be used

if there are at-risk individuals in the house. To

restrict access to a fireplace or stove, install an

adjustable safety gate to keep toddlers, young

children and other at-risk individuals out of the

room and away from hot surfaces.

Any safety screen or guard removed for servicing

an appliance must be replaced prior to operating

the appliance.

Clothing or other flammable materials should not

be placed on or near the fireplace.

Surveiller les enfants. Garder les vêtements, les

meubles, l’essence ou autres liquides à vapeur

inflammables lin de l’appareil.

Never allow anyone to use the fireplace if they

are unfamiliar with its operation.

NEVER store or use gasoline or any other flammable

vapors or liquids in the vicinity of the fireplace.

Never burn any solid materials (wood, cardboard,

paper, coal, etc.) in this gas fireplace. Use with

natural gas or propane fuel ONLY.

Any safety screen, glass or guard removed for

servicing the appliance must be replaced prior to

operating the appliance.

Do not slam or strike the glass panel.

This appliance is NOT for use with aftermarket

glass doors. Cet appareil ne sert pas avec des

portes en verre de marché des accessoires.

Wear gloves and safety glasses while installing

or performing maintenance procedures on this

appliance.

ATTENTION!

Shut off the main gas supply to the

appliance during battery replacement to the

receiver or burner control.

Always shut off the main gas supply to the

appliance during inspection, maintenance,

or cleaning.

WARNING!

Shock Hazard. Can cause severe injury or death.

This appliance is powered by line voltage.

Do not try to repair the components in this

appliance. In no way are the component

enclosures to be tampered with or opened.

Disconnect from line voltage during

installation or performing any maintenance.

Electrical Hazards

Be aware of electrical wiring locations when

cutting holes in walls and ceilings for termi-

nation.

This appliance power supply must be electri-

cally grounded in accordance with local codes

or, in the absence of local codes, with the cur-

rent ANSI/NFPA 70, National Electrical Code

or CSA C22.1-Canadian Electrical Code.

This appliance power supply incorporates a

three-prong (grounding) plug for protection

against shock hazard and should be plugged

directly into a properly grounded three-prong

receptacle. DO NOT CUT OR REMOVE THE

GROUNDING PRONG FROM THE PLUG.

Do not disconnect the lamp and fan power

cords from the appliance power supply (Fan

Control Module). Use the rocker switch to

control power to these parts.

Always disconnect (unplug) the main power

supply from its outlet when performing rou-

tine service on this appliance.

138914 Rev. K / 7.27.10

Installation

Hearth Requirements

The Jøtul GF 370 DV has been approved for installa-

tion directly on combustible floor materials, including

carpeting. No additional floor protection is required,

however, we recommend that the stove be installed

on a solid surface.

Stove Location

In selecting a location for the stove, consider the

following points:

1) Heat distribution

2) Vent termination requirements

3) Gas supply routing

4) Traffic areas, furniture, draperies, etc.

5) 120V electrical outlet availability

This stove may be located on or near conventional

construction materials, however, proper clearance to

combustibles must be maintained in order to provide

adequate air circulation around the appliance. Also, it

is important to provide adequate access around the

stove for servicing and proper operation.

The clearances specified in this manual are the

minimum requirements established as a result of

safety testing. A combustible material is anything

that can burn; i.e. sheet rock , wall paper, wood, fab-

rics, etc. These surfaces are not limited to those that

are visible and also include materials that may be

located behind non-combustible materials.

If you are not sure of the combustible nature of

a material, consult your local fire officials. “Fire-re-

sistant” materials are considered to be combustible.

They may be difficult to ignite, but will burn. “Fire

-rated” sheet rock is also considered combustible.

Stove and Vent Clearance

Requirements

Minimum Clearances: See figs. 3-5.

Rear: 3” (76 mm) - from Rear of the unit

Ceiling: 16 3/4” (425 mm) - from Stove Top

Corner: 5” (127 mm) - from Stove Top

Sides: 7” (178 mm) - from Stove Top

Minimum Clearances from the Vent Pipe

to Combustibles:

Horizontal Run:

Off the top of the pipe - 2” (51 mm) Alcove - 7” (178 mm)

Off the sides and bottom - 1” (25 mm)

Vertical Run:

All sides - 1” (25 mm)

ALCOVE SPECIFICATIONS:

Maximum Alcove Depth: 21 3/4” (55.2 cm)

Minimum Alcove Width: 31 1/4” (79.3 cm)

Minimum Ceiling Height: 62 1/4” (158.1 cm)











Figure 3. Corner Clearances.

Figure 4. Alcove and Wall Clearances.















Figure 5. Parallel Wall Clearances.

138914 Rev. K / 7.27.10

Venting Requirements

There are three types of venting configurations ap-

proved for use with this appliance:

• Vertical Venting / Vertical Termination

• Vertical Venting / Horizontal Termination

• Horizontal Venting / Snorkel Termination

This appliance is approved for use with the 4/6

direct vent systems manufactured by the companies

listed on page 8. Use parts of one manufacturer only

- DO NOT MIX VENT COMPONENTS FROM DIFFERENT

MANUFACTURERS WITHIN THE SAME SYSTEM.

Installation of any components not manufac-

tured or approved by Jøtul or failure to meet all clear-

ance requirements will void all warranties and could

result in property damage or bodily injury.

The approved vent configurations described

in this manual are derived from extensive testing

under controlled laboratory conditions. Gas appliance

performance can be negatively affected by variables

present in the installation environment, i.e.; atmo-

spheric pressure, strong prevailing winds, adjacent

structures and trees, snow accumulation, etc. These

conditions should be taken into consideration by the

installer and stove owner when planning the vent

system design.

Vertical Venting and Termination

The Jøtul GF 370 DV can be vertically vented through

a roof or ceiling. Follow these guidelines

 Steep roofs, nearby trees, or predominantly windy

conditions, can promote poor draft or down

draft conditions. In such cases, an increase to the

height of the vent may improve performance.

If an offset or elbow is necessary in the vertical

rise, the vent pipe must be supported every three feet

to avoid excessive stress on the offsets. Use listed Wall

Straps from any of the approved vent suppliers.

A maximum of two 90° or four 45° elbows may be

used in a vertical termination. Whenever possible,

use 45° elbows instead of 90° elbows as they

offer less restriction to the flow of flue gases and

intake air.

 A listed firestop is required at any floor penetra-

tion. The opening should be framed in according

to the manufacturer’s instructions.

 Always maintain a minimum 1" clearance from all

sides of the vertical vent system to any combus-

tible material.

 Minimum vertical termination height: 6 ft. of

vent pipe.

Approved Vent Manufacturers

The Jøtul GF 370 DV stove is approved for installation

with direct vent chimney components supplied by

the following manufacturers:

Simpson Dura-Vent, Inc.

P.O. Box 1510

Vacaville, CA 95696-1510 800-835-4429

Selkirk Corporation

1301 W. President George Bush Hwy, Suite 330

Richardson, TX 75080-1139 800-992-8368

American Metal Products (Amerivent)

8601 Hacks Cross Rd.

Olive Branch, MS 38654 800-423-4270

Security Chimneys International Limited

2125 Monterey, Laval, Québec

Canada, H7L 3T6 450-973-9999

Metal-Fab, Inc.

P.O. Box 1138

Wichita, KS 67201 316-943-2351

ICC, Inc.

400 J-F Kennedy St. Jerome, Quebec

Canada, J7Y 4B7 450-565 6336

IMPORTANT

• JOINT SEALING

REQUIREMENT:

APPLY A 1/8” BEAD

OF HIGH-TEMPERA-

TURE SEALANT OR

MIL-PAC® TO THE MALE

SECTION OF THE INNER

VENT PIPE. THE CE-

MENT SHOULD FORM

A SEAL BETWEEN THE

INNER AND OUTER PIPES. SEE FIG. 5. SEE VENT MANUFAC-

TURER’S INSTRUCTIONS.

• NEVER MODIFY ANY VENTING COMPONENT, OR

USE ANY DAMAGED VENTING PRODUCT.

• THE GAS APPLIANCE AND VENT SYSTEM MUST BE

VENTED DIRECTLY TO THE OUTSIDE OF THE BUILD-

ING AND NEVER ATTACHED TO A CHIMNEY SERV-

ING A SOLID FUEL OR GAS BURNING APPLIANCE.

EACH DIRECT VENT GAS APPLIANCE MUST HAVE

ITS OWN SEPARATE VENT SYSTEM. COMMON VENT

SYSTEMS ARE PROHIBITED.

• IF VENTING SYSTEM IS DISASSEMBLED FOR ANY

REASON, REINSTALL PER THE MANUFACTURER’S

INSTRUCTIONS PROVIDED FOR THE INITIAL INSTAL-

LATION.



Figure 6.

138914 Rev. K / 7.27.10

Horizontal Overhang

Vertical Wall

Termination

Cap

18.

min.

Lowest Discharge

Opening

18 min.

18.

min.

Figure 7. Minimum roof pen-

etration height and clearance

from adjacent surfaces - vertical

termination.

IT IS NECESSARY to add restriction to a vertical vent

installation to compensate for excessive draft. See

page 13; Exhaust Restriction Adjustment.

GAS VENT HEIGHT: In no case shall any discharge

opening on the cap be less than 18” (457 mm) hori-

zontally from the roof surface. See fig. 7.

Maximum Vent Height: 35 ft. above the appliance.

Masonry or Prefabricated Chimney

Conversion

The GF 370 DV is approved for use with direct vent

chimney conversion kits in a masonry chimney or

a prefabricated solid fuel listed chimney. These are

available from any of the manufacurer’s listed on

page 8.

The following installation requirements must be

followed:

1. Use the restrictor zone guidelines in the Vent

Window Diagram, fig. 17. In masonry chimney, a

fireclay liner or listed steel liner, must be present

the entire length of the chimney.

3. Overall venting should not exceed 35 ft. (10.67 m).

4. The liner must have an inside dimension of 6”

round or greater.

5. Prefabricated chimneys must be UL 103 or ULC

S-629 listed and have a minimum INSIDE diam-

eter of 6 inches, (150 mm). Prefabricated chimneys

must be listed for the specific manufacturer’s

conversion kit.

Figure 8. Vent System through a masonry chimney

using the Simpson Dura-Vent Chimney Conversion Kit

#934. Other manufacturers use similar designs. May

also be used in listed prefabricated chimneys.

#991 Vertical Termination Cap

Cap Adaptor-

included in

#934 Kit

Support/Wall

Thimble Cover

- included

in#934 Kit

Exhaust Gas

Intake Air

Use Standard

Simpson Dura-

Vent GS Pipe

from stove to

thimble

4” Flex Pipe

not included

in kit

IMPORTANT NOTICE

THE USE OF AN EXISTING CHIMNEY AS AN AIR

INTAKE IS NOT COVERED UNDER THE ANSI

Z21.88-1999-CSA 2.33-M99 TEST METHODS

AND RESULTING ITS/WHI PRODUCT CERTI-

FICATION. THE CODE AUTHORITY HAVING

JURISDICTION MUST BE CONSULTED PRIOR

TO PROCEEDING WITH THIS INSTALLATION

METHOD.

138914 Rev. K / 7.27.10







Horizontal Termination

 Minimum vertical rise from the vent collar is a 24”

section vent pipe. See fig. 9. Minimum horizontal

run is 12” with natural gas and 18” with propane.

A maximum of two 90° or four 45° elbows may

be used in a horizontal termination. Whenever

possible, use 45° elbows instead a 90° elbow as

they offer less restriction to the flow of flue gases

and intake air. Reduce the overall horizontal run

by 4 feet for each 90° elbow, and 2 feet for each 45°

elbow.

Snorkel Termination - ( 14” or 36”):

NATURAL GAS ONLY. DO NOT USE SNORKEL

TERMINATION WITH PROPANE FUEL.

A horizontal vent run may be made with a 90°

elbow directly to the rear of the stove only when

terminated by a 14 or 36 inch snorkel cap. Fig. 10

shows the minimum vent pipe requirements.

14” Snorkel: The maximum horizontal vent run

must not exceed a 24” section of pipe and must be

a minimum of 12”.

36” Snorkel: The maximum horizontal vent run

must not exceed 5 feet and must be a minimum

of 12”.

The termination cap must not be recessed into

the wall or siding. Do not fill air space in wall around

termination cap with any type of insulation.

Wall Cut-out: A minimum 10” X 10” square hole

is adequate for proper pipe clearance through a

wall, provided the vent is positioned to maintain

2” minimum clearance at the top. A 1” minimum

clearance must be maintained to combustible

material around the other sides. See fig. 11.

Any horizontal run of vent must have a 1/4” rise for

every foot of run toward the termination cap.

All horizontal terminations must comply with the

clearance specifications to adjacent structures as

indicated in fig. 12.

Installation of a Vinyl Siding Standoff is required

to prevent damage to vinyl siding between the

vent cap and the exterior wall.

A horizontal termination cap must maintain a 3”

clearance to any overhead combustible projections that

are 2 1/2” or less. It must also maintain a 12” clearance

from projections that exceed 2 1/2”. See fig. 13.

Vinyl siding projections require a default clearance of

18” to the vent terminal.











Figure 10. Minimum vent

pipe sections required for a 14”

Snorkel termination - Natural

Gas ONLY.

Figure 9. Minimum vent

pipe sections required for

horizontal termination:

A = 12” with NG

18” with LP

Figure 11. Install a

listed wall thimble

according to manu-

facturer’s instructions

to maintain required

clearance to combus-

tible materials.





Listed Wall

Thimble

Listed Wall

Thimble

138914 Rev. K / 7.27.10















Figure 13.

Termination clearance to overhangs.

A = Clearance above grade, veranda, porch , deck, or balcony

: 12 inches (30 cm) minimum.

B = Clearance to window or door that may be opened:

**Min. 9 inches, U.S. / *12 inches (30 cm) CAN.

We recommend 12 in. minimum to prevent condensation

on the window.

C = Clearance to permanently closed window:

**Min. 9 inches, U.S. / *12 inches (30 cm) CAN

We recommend 12 in. minimum to prevent condensation

on the window.

D = Vertical clearance to ventilated soffit located above the

terminal within a horizontal distance of 2 feet (60 cm)

from the center line of the terminal: 18 inches

(46 cm) minimum.

E = Clearance to unventilated soffit: 12 inches (30 cm)

minimum.

F = Clearance to outside corner: **Min. 9 inches, U.S. / *12

inches (30 cm) CAN. We strongly recommend 12 inches,

particularly where windy conditions prevail.

G = Clearance to inside corner: ** Min. 6 inches, U.S. / *12

inches (30 cm) CAN. We strongly recommend 12 inches,

particularly where windy conditions prevail.

H = *Not to be installed within 15 feet (4.5 m) above a me-

ter/regulator assembly within 3 feet (90 cm) horizontally

from the center line of the regulator.

I = Clearance to service regulator vent outlet:

3 feet (91 cm) minimum.

J = Clearance to non-mechanical air supply inlet to building

or the combustion air inlet to any other appliance:

12 inches (30 cm) minimum.

K = Clearance to a mechanical air supply inlet:

**Min. 3 feet (91 cm) above if within 10 feet horizontally,

U.S. / *6 feet (1.83 m) minimum / CAN

L =

Clearance above paved sidewalk or a paved driveway

located on public property: 7 feet (2.1 m) min.

M = Clearance under veranda, porch, deck, or balcony:

12 inches (30 cm) minimum.

* In accordance with CSA B149 Installation Codes.

** In accordance with the current ANSI Z223.1/NFPA 54, National

Fuel Gas Code. Note: Local Codes and Regulations may require

different clearances.

A vent shall not terminate directly above a sidewalk or driveway

which is located between two single family dwellings and serves

both dwellings.

Only permitted if veranda, porch, deck, or balcony, is fully open

on a minimum of two sides beneath the floor.*

Figure 12. Horizontal termination clearances







138914 Rev. K / 7.27.10

Intake Air Adjustment

An Intake Air shutter plate allows further burner

adjustment for taller vent runs. It is located under the

firebox floor and is set fully open at the factory. See

fig. 16.

The shutter has an adjustment range of 1 inch.

To change the setting, loosen the wingnut and slide

the gasketed shutter stem backward to the half or

fully closed positions, depending on which vent zone

is appropriate. Retighten the wingnut before lighting

the burner to seal the gasket. Allow the flame pattern

to settle in for 10- 15 minutes between each setting

change.

















Figure 15. Exhaust Restrictor settings

Figure 14. The Exhaust Restrictor is located within the

vent adaptor collar.

Exhaust Restrictor Adjustment

1. Remove the Trim Rings from the Top Plate.

2. Loosen the locking screw and turn the restrictor

pivot plate to the appropriate indicator point as

specified in the vent window diagram, figure 17.

After the burner has been operating for 15 minutes,

make any further adjustment in 1/8” increments

until the desired flame picture is achieved. Do not

exceed the fully closed setting as shown in fig. 15.

Operate the burner for 10-15 minutes between ad-

ditional adjustments.

3. Tighten the locking screw and replace the Trim

Rings.

Vent Restriction Adjustments

The Jøtul GF 370 DV features adjustment controls for

both intake air and exhaust to accommodate a variety

of conditions that result from variables inherent in the

vent configuration and environment. Both controls

can be accessed from outside the firebox to allow the

burner to be “dialed-in” under operation. See figures 14

and 16.

Use the Vent Termination Diagram, fig. 17, to

determine which zone your vent termination falls

within and make the appropriate exhaust and air

intake setting adjustments. Use these settings as

general guidelines to start from. The final settings

will ultimately be determined by the individual

characteristics of your particular installation.

There are no hard and fast rules.

Figure 16. Air intake shutter location.

Zone D

Vent terminations within Zone D are susceptible

to draft conditions that may interfere with the

intermittent Pilot Ignition functionality. In such

cases, we recommend that the stove be operated

only in Continuous Pilot Ignition mode.





Exhaust Vent Restriction

Exhaust restriction prevents overly strong draft

that can interfere with pilot function, cause poor

combustion or a weak flame picture. The shutter is

set in the fully open position at the factory. The final

position of the restriction shutter is determined by

where the vent termination falls within the vent

window diagram.

For example, if the vent rise is 20 feet and

includes one elbow in a horizontal run of 5 feet, the

appropriate exhaust setting will be Full Restriction.

Top Plate

Pivot Plate

138914 Rev. K / 7.27.10

Figure 17 . Vent Termination Diagram.























































 





  

   

 

       



Intake Air - Fully Closed

Full Exhaust Restriction

Half Exhaust Restriction

No Exhaust Restriction

Intake Air - Fully Open

Intake Air - Half Closed























ANY VENTING WITH A VERTICAL RISE MUST

TERMINATE (END) WITHIN THE SHADED AREAS.

A maximum of two

90° or four 45° elbows

may be used. When-

ever possible, use 45°

elbows instead of 90°

elbows as they of-

fer less restriction to

the flow of flue gases

and intake air. Use of

elbows may adversely

affect IPI functional-

ity. In such cases, CPI

mode should be used.

Reduce the overall

horizontal run by

4 feet for each 90°

elbow, and 2 feet for

each 45° elbow.

When two or more

elbows are used in a

horizontal run, a less

restricted setting may

be more effective than

that indicated by the

termination zone dia-

gram.

138914 Rev. K / 7.27.10

Stove Assembly

1. Glass Frame Removal

To access the firebox, use the 4 mm hex key to

remove the four socket head screws that attach the

glass frame to the firebox. See fig. 18.

2. Routing the Power Supply

The power cord located in the valve compartment is

connected to the Fan Control Module which is the

main power supply for all stove operating functions.

Route the cord through the pedestal and out the rear

of the pedestal base as in fig. 18, or through the floor.

CAUTION: Take care that the pedestal base does not

pinch the power cord. You should be able to feel free

play in the cord.

The 10 foot extension power cord, supplied in

the hardware bag, is intended to connect the interior

cord to the nearest 120V house current outlet.

DO NOT CONNECT THE STOVE TO HOUSE CUR-

RENT UNTIL THE INSTALLATION IS COMPLETE AND

YOU ARE READY TO INITIATE THE FIRST BURN.

Figure 18.

Glass frame

removal.

3. Connecting the Gas Supply

Gas Supply Requirements

ALL INSTALLATIONS MUST COMPLY WITH LOCAL

CODE OR IN THE ABSENCE OF LOCAL CODE, MUST

COMPLY WITH THE MOST RECENT EDITION OF THE

NATIONAL FUEL GAS CODE ANSI Z223.1/NFPA 54 OR

CAN-B149.

Shut-off Valve

All codes require a gas shut-off valve (gas cock)

and union to be installed in the supply line within 6

feet of the appliance. This allows for the disconnec-

tion of the stove for servicing and maintenance. See

Fig. 19.

A T-HANDLE GAS SHUT-OFF VALVE IS RE-

QUIRED IN MASSACHUSETTS IN COMPLIANCE

WITH CODE 248CMR.

THIS PRODUCT MUST BE INSTALLED BY A

LICENSED MASTER OR JOURNEYMAN PLUMBER

OR GAS-FITTER WHEN INSTALLED IN THE

COMMONWEALTH OF MASSACHUSETTS.

The stove and gas control valve must be discon-

nected from the gas supply piping during any pres-

sure testing of the system at test pressures in excess

of 1/2 psig. For pressures lower than 1/2 psig, isolate

the gas supply by closing the manual shut-off valve.

Control Valve Connection

The gas supply line connection to the stove flex

line can be made at the rear of the base plate or

through the floor. The gas supply line should be a

minimum 3/8” inside diameter, or the appropriate

size to provide sufficient gas pressure to the valve

regardless of the input setting.

The use of flexible gas appliance connectors is ac-

ceptable in many areas in the U.S. In Canada, methods

vary depending on local code. If local codes permit,

use flexible gas line for ease of installation and ser-

vice. For those locales where flexible gas lines are not

permitted, use the 3/8” iron fitting to make the con-

nection at the top side of the Control Valve. See fig. 19.

Secure all joints tightly using appropriate tools

and sealing compounds (for propane units, be sure to

use compounds that are propane resistant). Turn on

gas supply and test for gas leaks using a 50/50 soapy

water solution or a gas detector.

138914 Rev. K / 7.27.10

Figure 19. Gas supply valve types and fittings.



























Soap Solution Leak Test

• Mix a 50-50 solution of water and dish soap.

• Light appliance - see lighting instructions on the

back cover of this manual or on the rating plate.

• Brush or spray all joints and connections with the

soapy water solution.

• If bubbles appear at any connection or seam or a

gas odor is detected, immediately turn gas control

knob to the OFF position.

Tighten or reconnect the leaking joint and retest

for any gas leaks.

The line must be disconnected from the gas sup-

ply line by closing the main supply manual gas shut-

off valve (gas cock) during any pressure testing of the

gas supply piping system that is equal to or exceeds

pressures of 1/2 psig (3.5 kPa).

4. Testing Gas Pressure

Proper gas pressure provides a consistent flow of gas

to the appliance and is instrumental in checking for

gas leaks. There are two pressure test points on the

front of the stove control valve where test gauge con-

nections are made. See Fig. 20. Gauge connections

are identified by:

• E for inlet or supply pressure ( the amount of gas

coming to the valve.)

• A for manifold pressure (the amount of gas that is

coming out of the valve to the burner.)

WARNING

DO NOT ALLOW THE INLET GAS PRESSURE TO

EXCEED 14.0” WC (OR 1/2 PSIG) AS SERIOUS

DAMAGE TO THE VALVE MAY RESULT.

NEVER USE AN OPEN FLAME TO CHECK FOR GAS

LEAKS.

ALWAYS REFER TO THE LIGHTING INSTRUCTIONS

ON THE INSIDE BACK COVER OF THIS MANUAL

WHEN LIGHTING THE STOVE.

Figure 20. Pressure test points located on the front

of the valve.

Manifold

Inlet

Pilot Adjustment

Inlet Pressure

MIN MAX

Natural Gas: 5.0 WC (1.24 kPa) 7.0 WC (1.74 kPa)

Propane: 12.0 WC (2.99 kPa) 14.0 WC (3.48 kPa)

Manifold Pressure

MIN MAX

Natural Gas: 1.6 WC (0.398 kPa) 3.5 WC (.87 kPa)

Propane: 6.4 WC (1.59 kPa) 10.0 WC (2.48 kPa)

ALWAYS TEST PRESSURES WITH VALVE REGULATOR

CONTROL AT THE HIGHEST SETTING.

Symptoms of incorrect gas pressure include:

Insufficient gas pressure:

• Small pilot flame which can result in insufficient

millivolts.

• Little variation in flame picture between HI and LO

regulator settings.

• Insufficient gas to support more than one appli-

ance causing nuisance outages or gas surges.

Excessive gas pressure:

• Permanent damage to valve causing complete ap-

pliance shut down.

• Too large a pilot flame resulting in overheating of

the power generator and consequent shut down.

• Sooting due to impingement and/or incorrect fuel

to air mix.

138914 Rev. K / 7.27.10

• Label B - apply to the rating plate in the space indi-

cated on the plate.

• Small valve label - apply to valve body

• Conversion instructions

5. Fuel Conversion

The GF 370 DV gas stove is shipped from the factory

equipped to burn Natural gas. Propane fuel conver-

sion kit 156800 is included with the stove to enable

use with LP gas if necessary. The kit contains all the

components needed to complete the task and ensure

safe operation, including labels that must be affixed

to the stove.

CAUTION: Before proceeding with this conversion,

the gas supply must be shut off prior to disconnecting

the electrical power.

This conversion kit shall be installed by a qualified

service agency in accordance with the manufacturer’s

instructions and all applicable codes and requirements

of the authority having jurisdiction. If the informa-

tion in these instructions is not followed exactly, a fire,

explosion, or production of carbon monoxide may result

causing property damage, personal injury or loss of life.

The qualified service agency is responsible for the proper

installation of this kit. The installation is not proper and

complete until the operation of the converted appliance

is checked as specified in the manufacturer’s instructions

supplied with the kit.

Cet équipement de conversion sera installé par une

agence qualifiée de service conformément aux instruc-

tions du fabricant et toutes exigences et codes appli-

cables de l’autorisés avoir la juridiction. Si l’information

dans cette Instruction n’est pas suivie exactement, un

feu, explosion ou production de protoxyde de carbone

peut résulter le dommages causer de propriété, pert ou

blessure personnelle de vie. L’agence qualifiée do service

est esponsable de l’installation propre de cet équipe-

metn. L’installation n’est pas propre et complète jusqu’à

l’operation de l’appareil converi est chéque suivant les

critères établis dans les instruction de propriétaire provi-

sion nées avel l’équipement.

Fuel Conversion Procedure

1. Turn off gas supply to the stove and disconnect

from electrical power source.

2. Remove the glass frame. See fig. 18.

3. Loosen the primary air shutter wingnut and push

the stem all the way back. Fig. 21.

4. Pull the Burner Plate forward to disengage it from

the burner orifice and lift it out of the firebox.

5. Locate the main burner injector. See fig. 23 on

page 17. Slide the Air Shutter out of the way and

use a 1/2” open end wrench or deep-well socket to

remove the burner orifice from the brass orifice

holder. Replace with the orifice supplied in the

kit. Tighten securely.

6. Change the Air Shutter position: Lift the shutter

tube up in its hinge pin slots and turn the tube

over, so that the appropriate fuel type indicator

(LP or NG) is oriented facing you. See fig. 22. Push

the shutter all the way back over the injector.

7. Change the Pilot Orifice. Pull the Pilot Hood off of

its base. It will snap by the retainer clip shown in

Fig. 23.





Figure 21.

Figure 22. Primary air shutter orientation must be

changed for fuel type.









Conversion Kit (LP #156800, NG #156801)

Tools required:

• 1/2” & 13 mm open end wrench or deep-well socket

• Torx T20 or slotted screwdriver

• 7/16” open end wrench

• 3 mm allen wrench

Conversion Kit Contents:

• 1 regulator tower labeled for the appropriate fuel

• 2 regulator tower Torx screws

• 1 burner injector (#38 mm for NG, #53 for LP)

• 1 pilot orifice (#62 for NG, #35 for LP)

• Label A - to be completed and applied to the base

of the valve compartment

• 1/4” nut driver

• 4 mm allen wrench

138914 Rev. K / 7.27.10

Using a 4 mm allen wrench, unscrew the pilot

orifice. Replace it with the orifice from the kit.

Be sure the new orifice is tightly secured to pre-

vent by-pass leakage.

Replace the pilot hood by simply pushing it

back into place on its base.

8. Reinstall the Burner Plate by engaging the ven-

turi tube with the Air Shutter. BE CERTAIN THE

BURNER IS LEVEL AND SECURELY SEATED ON THE

SUPPORT LEGS ON THE FIREBOX FLOOR.

9. Replace the variable regulator. Using a Torx T-20

screwdriver, remove the two specialty screws

from the regulator tower on the front of the

valve. Note: To help identify which screws to remove,

refer to the new regulator in the kit. See fig. 23.

10. Disconnect the Regulator wire lead from the

receptacle housing terminal. Remove the regula-

tor tower and the rubber diaphragm.

11. Install the new variable regulator tower from the

kit. Be sure that the gasket is properly positioned

and tighten screws securely. Connect the wire lead.

12 . Apply the identification labels to the stove so that they can

be seen by any person that may be servicing the stove.

• Label “A”: Apply to front lip of the valve compartment.

• Label “B”: Apply to the Rating Plate.

• Small valve sticker: Apply to valve.

13. Install the accessory panels and burner media as

appropriate. See pages 19-21.

14. Apply anti-seize lubricant to the socket head glass

frame screws before reinstalling the glass frame.

15. Apply gas to the system and check for leaks using

a soapy water solution or gas sensor.

16. Follow the System Check instructions on pages 22-23

for initial start-up and flame picture adjustment.

Flame Sensor

Pilot Orifice

Injector

Figure 23. Fuel conversion components and assemblies

Primary Air

Shutter

Regulator

Diaphragm

Regulator

Tower

Use new Torx

screws supplied

Apply Label

“A” Here

Retainer Clip

Ignitor

Pilot Head

Tab & Receptacle

Terminals

138914 Rev. K / 7.27.10

6. High Altitude Adjustment

The decreased atmospheric pressure of higher alti-

tudes affects heat value of gaseous fuels. Most gas

suppliers derate the gas intended for use at eleva-

tions above 2000 feet. Check with your gas supplier

before performing derate adjustment to the burner.

This appliance may be adjusted for altitude over

2000 ft. (610 - 1371 m) for natural gas.

If the gas supplier does not derate fuels, install High

Altitude Adjustment Kit 156822 for Natural gas.

DO NOT DERATE FOR PROPANE.

U.S & Canada per

ANSI Z21.88-2005•CSA 2.33-2005, CAN/CGA 2.17

For natural gas installations from 610-1370 meters

(2000-4500 ft.) the orifice size (DMS) is #39. See

data plate for additional information. For high

altitude installations consult the local gas distributor

or the authority having jurisdiction for proper rating

methods. If the installer must convert the unit to

adjust for varying altitudes, the information sticker

must be filled out and applied to the appliance at the

time of the conversion.

INSTALLER: Fill out the appropriate information

and apply the high altitude conversion label provid-

ed to the rating plate on the appliance. See fig. 24.

Derating Procedure

• Follow Steps 1-6 of the Fuel Conversion procedure

on pages 16 to change the burner injector. Use the

injector supplied with the kit. Detailed instruc-

tions are also included in the kit.

• Conduct gas leak and gas pressure tests as de-

tailed on page 15 of this manual.

• Conduct system check and flame picture adjust-

ments as specified on pages 22-23.

Figure 24. High Altitude Conversion Label.

This appliance has been converted for use at an

altitude of___________ .

Orifice Size: __________ Manifold Press. _______

Input Btu/Hr. _________ Fuel Type ___________

Date: ___/___/___ Converted by:_____________

Cet appreeil a été converti au _____ Injecteur_____

Pression à la tubulure d’alimentation ___________

Déoit calorifique ___________

7. Firebox Panel Installation

for Skamol Panels

and optional

Reflective Glass Kit 156817

You will need to remove the pilot hood and burner

plate to provide clearance to install either panel kit.

Pull the pilot hood off of the pilot base - it will slip

past its retainer clip. Simply lift the burner up and out

of the firebox.

Skamol Panels

DO NOT OPERATE THIS STOVE WITHOUT THE SKA-

MOL PANELS INSTALLED. If desired, the panels may be

painted black using any high-temperature paint.

1. Install the Rear Panel.

Orient the panel with the bevelled edges facing

back, matching the angles of the firebox walls.

Tilt the panel to engage the upper edge behind

the two retainer brackets at the top of the fire-

box. Push the panel all the way back and centered

against the firebox wall. See fig. 25a.

2. Install the Side Panels.

Orient each panel with the rounded edge facing

forward. Tilt the panel to engage the upper edge

behind the retainer clip at the top of the firebox.

See fig. 25b.

3. Replace the burner plate. When properly located, it

will be level and secure.

4. Replace the pilot head. It will just snap back into

place on the base.

Reflective Glass Panels

Use the cotton gloves to handle the panels to prevent

fingerprints on the surfaces. Fingerprints are difficult

to remove. Use a clean cloth to remove any dust from

the glass panels.

1. Use pliers to bend down the center tab of each

retainer bracket. This is the “keeper” for the side

panels which will, in turn, hold the rear panel in

place. See fig. 26a.

2. Orient the rear panel, shiny side out, textured side

in. Tilt the panel to engage its upper edge behind

the retainer brackets. Be sure it is pushed all the way

back and centered. See fig. 26b.

3. Orient the side panels, shiny side out, and slide

each behind the center tab of the retainer bracket.

See Fig. 26c.

4. Replace the burner plate. When properly located, it

will be level and secure.

5. Replace the pilot head. It will just snap back into

place on the base.

Cet appareil est equippé pour des altitudes compries

entre 0 et 2000 pieds (0-610 m ) seulement.

138914 Rev. K / 7.27.10

8. Install Burner Media

Wishing Rock

CAUTION: THE ROCKS ARE FRAGILE! SUPPORT THE

ASSEMBLY FROM THE BOTTOM AND HANDLE CARE-

FULLY!

1. Engage the Wishing Rock bed with the two center

burner pins as shown in fig. 27.

2. Evenly disperse the Ember Stones supplied over

the burner plate around the log parts. DO NOT

ALLOW EMBER STONES TO BLOCK THE PILOT AS-

SEMBLY AREA. The carry-over ports directly in front

of the pilot must remain clear for proper pilot

ignition. See figs. 29 and 65 for examples.

Starfire Glass

Do not use more than the four pounds (in two, 2 lb.

bags) of glass media provided. For best results, evenly

spread the contents of the bag over the entire burner

plate and rear skirt, mounding a crown toward the

center. DO NOT COVER THE AREA IMMEDIATELY IN

FRONT OF THE PILOT ASSEMBLY. The carry-over ports

directly in front of the pilot assembly must be clear to

ensure proper pilot ignition. See fig. 66 page 34.

Figure 27. Set Wishing Rock assembly on pins.

Figure 25a.

Install Rear Skamol

Panel.

Rear Skamol Panel

Retainer Brackets

Figure 25b.

Install Rear Skamol

Panels.

Figure 26b.

Install Rear Glass

Panel.

Figure 26c.

Install Side Glass

Panels.

Figure 26a.

Bend center tab to

retain glass panels.

Side Skamol Panel

Rear Glass Panel

Side Glass Panel

Side Skamol Panel

138914 Rev. K / 7.27.10

Figure 28. Engage the Bottom Log with the two

center pins in the burner plate.

Install the Log Set

The three-piece log set includes a bag of ember

stones that simulate glowing coals when the burner

is operating.

Use workgloves and handle the individual logs

carefully, supporting each with both hands. Install

the Logset and Ember Stones as shown in figures

28-31.

Figure 29. Lean the Right Log up against the upper

right corner of the firebox and engage its toe with the

indentation in the Bottom Log.

Figure 30. Engage the Left Log with the rear burner

plate pin.

Figure 31.

Evenly disperse the Ember Stones evenly over the

burner plate around the log parts. DO NOT ALLOW

EMBER STONES TO BLOCK THE PILOT ASSEMBLY AREA.

The carry-over ports directly in front of the pilot must

remain clear for proper pilot ignition.

Replace the Glass Frame.

Reinstall the glass frame using the 4 mm hex key

and socket head screws previously removed.





La page charge ...

Jøtul GF 370 DV Installation And Operation Instructions Manual

Marque: Jøtul

Modèle: GF 370 DV

Catégorie: Poêles

Taper: Installation And Operation Instructions Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Jøtul GF 370 DV

Jøtul GF 370 DV Installation And Operation Instructions Manual

Jøtul GF 370 DV Installation And Operation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents