Jøtul GF 200 DV II Lillehammer Installation And Operation Instructions Manual

Marque: Jøtul

Modèle: GF 200 DV II Lillehammer

Catégorie: Cheminées

Taper: Installation And Operation Instructions Manual

Installation and

Operation Instructions

Jøtul GF 100 DV II Nordic QT

Jøtul GF 200 DV II Lillehammer

DirDir

Direcec

ecec

ectt

t VV

Venen

enen

entt

t Gas St Gas St

Gas St Gas St

Gas Stoo

ovv

vee

– QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE

GAZ:

• Ne pas tenter d’allumer l’appareil.

• Ne touchez à aucum interrupteur. Ne pas

vous servir des téléphones se trouvant

dans le bâtiment où vous trouvez.

• Appelez immédiatement votre

fournisseur de gaz depuis un voisin. Suivez

les instructions du fournisseur.

• Si vou ne pouvez rejoindre le fournisseur

de gaz, appelez le service des incendies.

– L’installatione l’entretien doivent être

assurés par un installateur ou un service

d’entretien qualifié ou par le fournisseur

de gaz.

– Ne pas entreposer ni utiliser d’essence ni

d’autres vapeurs ou liquides inflammables

dans le voisinage de cet appareil ou de tout

autre appareil.

– Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

– WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Immediately call you gas supplier from

a neighbor’s phone. Follow the gas

supplier’s instruction.

• If you cannot reach your gas supplier,

call the fire department.

– Installation and service must be

performed by a qualfied installer,

service agency or the gas supplier.

– In the Commonwealth of

Massachusetts, a carbon monoxide (CO)

detector shall be installed in the same

room as the appliance.

WARNING: If the information in these

instructions is not followed exactly, a fire

or explosion may result causing property

damage, personal injury or loss of life.

AVERTISSEMENT: Assurez-vous de bien

suivreles instructions données dans cette

notice pour réduire auninimum le risque

d’incendie ou d’explosion ou pour éviter tout

dommage matériel, toute blessure ou la mort.

CAUTION: THESE INSTRUCTIONS MUST

REMAIN WITH THE HOMEOWNER.

ATTENTION : CES INSTRUCTIONS DOIVENT

DEMUERER AVEC LE PROPRIÉTERE D’UNE

MAISON.

THIS PRODUCT MUST BE

INSTALLED BY A LICENSED PLUMBER OR

GAS-FITTER WHEN INSTALLED IN THE

COMMONWEALTH OF MASSACHUSETTS.

We recommend that our gas

products be installed and

serviced by professionals who

are certified in the U.S. by the

National Fireplace Institute®

(NFI) as NFI Gas Specialists.

Table of Contents

Specifications, Jøtul GF 100 DV II......... 4

Specifications, Jøtul GF 200 DV II ........ 5

General Information ............................... 6

Service Tools ............................................. 6

Safety Information .................................. 7

Installation Requirements

Location ................................................ 7

Hearth Protection .............................. 7

Clearances .......................................... 8

Mantel & Trim ..................................... 8

Alcove .................................................... 8

Vent Requirements

Adding Restriction.............................. 9

Vertical Termination ........................ 10

Horizontal Termination .................... 12

Vent Terminal Clearances ............... 14

Mobile Home Installation .................... 15

Fuel Conversion ...................................... 15

Gas Connection ...................................... 17

Gas Pressure ........................................... 18

High Altitude Adjustment .................. 18

Air Shutter Adjustment ....................... 19

Wall Thermostat ....................................20

Remote Control......................................20

Log Set Installation ...............................20

System Check .......................................... 21

Operation ................................................ 22

Maintenance .......................................... 22

Glass Replacement............................ 22

Optional Blower .................................... 24

Illustrated Parts Breakdown ......... 26, 27

Replacement Parts List.................. 28, 29

Addendum - Brick Panel Kit ................30

Lighting Instructions ............ Back Cover

Direct Vent Gas Heaters

Manufactured and Distributed by:

Jøtul AS

Fredrikstad, Norway

Jøtul North America

Gorham, Maine

Test Standards

This appliance complies with U.S. and Canadian

National Safety standards and is tested and

listed by Intertek Testing Services of Middleton,

Wisconsin to:

ANSI Z21.88-2005,

ANSI Z21.88a / CSA 2.33a - 2007,

CAN/CGA 2.17-M91,

and CSA P.4.-01.2

DO NOT ATTEMPT TO ALTER OR MODIFY THE

CONSTRUCTION OF THE APPLIANCE OR ITS

COMPONENTS. ANY MODIFICATION OR

ALTERATION WILL VOID THE WARRANTY,

CERTIFICATION AND LISTING OF THIS APPLIANCE.

N.Y.C. Dept. of Buildings

MEA No. 369-04-E

Jøtul GF 200 DV II Lillehammer

and

DV II Nordic QTJøtul GF 100

Jøtul GF 100 DV II Nordic QT

Specifications

Input Rates

Natural Gas

17,000 BTU/hr. maximum input

9,900 BTU/hr. minimum input

Propane

16,000 BTU/hr. maximum input

8,700 BTU/hr. minimum input

Inlet Pressure: MIN MAX

Natural Gas: 5.0 WC (1.24 kPa) 7.0 WC (1.74 kPa)

Propane: 12.0 WC (2.98 kPa) 14.6 WC (3.63 kPa)

Manifold Pressure:

MIN MAX

Natural Gas: 1.2 WC (0.29 kPa) 3.8 WC (0.94 kPa)

Propane: 2.9 WC (0.72 kPa) 11.0 WC (2.74 kPa)

Piezo Ignitor / Standing Pilot

Weight: 150 lbs.

Jøtul GF 100 DV II Miscellaneous Kit

Contents

• Fuel Conversion Kit - LP ................................. 155628

• Rear Air Intake Restrictor Plate,.... Black -22111092

or Jøtul Iron - 22111085

• Side Air Intake Restrictor Plates, (2) ...... 22099192

or Jøtul Iron - 22099185

* Decorative Wall Shield, Black ................. 22092692

or Jøtul Iron ........ 22092692

Jøtul GF 100 DV II Accessories

• Blower Kit .......................................................... 155631

• Antique Brick Kit .............................................. 155815

• Fuel Conversion Kit - NG ............................... 155629

• Wall Thermostat ............................................ 750003

• Remote Control ............................................... 129706

• Mobile Home Floor Bracket Kit ................... 154342

•Universal Leg Leveler Kit .............................. 156096

The Jøtul GF 100 DV II Nordic QT is a Direct Vent gas

heater designed as a sealed combustion, air circulat-

ing gas appliance for residential applications. This

appliance is approved for installation using

6 5/8" X 4" direct vent pipe and components from the

following manufacturers:

Simpson Dura-Vent GS

Security Vent, Ltd.

Amerivent Inc.

Selkirk Metalbestos

Metal-Fab, Inc.

ICC, Inc. - ExcelDirect Vent

The Jøtul GF 100 DV II Nordic QT gas stove is de-

signed to burn NATURAL GAS or PROPANE only. It is

shipped from the factory equipped to burn Natural

Gas. If use with Propane is desired, the stove must

first be converted for use with that gas. Use the LP

Fuel Conversion Kit 155628 included with this stove

See page 14 for instructions.

18 1/4”

464 mm 16 3/4 ”

425 mm

16 3/4”

425 mm

Flue Collar

Centerline

14”

356 mm

21”

533 mm

22 1/4”

565 mm

Leg To

Leg

Jøtul GF 200 DV II Lillehammer

Specifications

Jøtul GF 200 DV II Accessories

• Fuel Conversion Kit - NG ....................................................... 155627

• High Altitude Adjustment Kit - NG ................................. 155808

• High Altitude Adjustment Kit - LP .................................. 155809

• Blower Kit ................................................................................... 155631

• Antique Brick Kit ...................................................................... 155815

• Wall Thermostat .................................................................... 750003

• Remote Control ....................................................................... 129706

• Universal Leg Leveler Kit ......................................................156096

• Mobile Home Floor Bracket Kit ..... GF 200 DV II (6”) / 154923

.............................................................. for Long Legs (8”) / 750304

......................................................................... for Plinth Kit / 154342

• Long Leg Kits ............................................... Matte Black / 154929

........................................................................... Blue Black / 154930

........................................................................ Forest Green / 154931

.................................................................................... Ivory / 154932

................................................................................ Jøtul Iron / 155366

• Plinth Kits .................................................... Matte Black / 350081

.......................................................................... Blue Black / 350082

..................................................................................... Ivory / 350083

.................................................................. Forest Green / 350084

.............................................................................. Jøtul Iron / 350085

Input Rates

Natural Gas

20,000 BTU/hr. maximum input

11,400 BTU/hr. minimum input

Propane

18,000 BTU/hr. maximum input

8,450 BTU/hr. minimum input

Inlet Pressure: MIN MAX

Natural Gas: 5.0 WC (1.24 kPa) 7.0 WC (1.74 kPa)

Propane: 12.0 WC (2.98 kPa) 14.6 WC (3.63 kPa)

Manifold Pressure: MIN MAX

Natural Gas: 1.2 WC (0.29 kPa) 3.8 WC (0.94 kPa)

Propane: 2.9 WC (0.72 kPa) 11.0 WC (2.74 kPa)

Piezo Ignitor / Standing Pilot

Weight: 180 lbs.

The Jøtul GF 200 DV II Nordic QT is a Direct Vent gas

heater designed as a sealed combustion, air circulat-

ing gas appliance for residential applications.

This appliance is approved for installation using

6 5/8" X 4" direct vent pipe and components from

the following manufacturers:

Simpson Dura-Vent GS

Security Vent, Ltd.

Amerivent Inc.

Selkirk Metalbestos

Metal-Fab, Inc.

ICC, Inc. - ExcelDirect Vent

The Jøtul GF 200 DV II Lillehammer gas stove is

designed to burn NATURAL GAS or PROPANE only.

It is shipped from the factory equipped to burn

Natural Gas. If use with Propane is desired, the stove

must first be converted for use with that gas. Use the

LP Fuel Conversion Kit 155626 included with this stove

See page 14 for instructions.

Jøtul GF 200 DV II Miscellaneous Kit Contents

• Fuel Conversion Kit - LP ................................. 155626

• Rear Air Intake Restrictor Plate,.... Black -22111092

or Jøtul Iron - 22111085

• Side Air Intake Restrictor Plates, (2) ...... 22099192

or Jøtul Iron - 22099185

* Decorative Wall Shield, Black ................. 22092692

or Jøtul Iron ........ 22092692

Height Dimensions with Optional Legs:

Plinth Kit - subtract I” (25 mm)

Long Legs - add 2 1/4” (57 mm)

13”

330 mm

Leg To

Leg

18 1/2”

470 mm

18 ”

457 mm

21 1/8”

537 mm As shipped

with 6” (152

mm) Legs

24 3/4”

630 mm

24 3/4”

630 mm

22 3/4”

560 mm

General Information

THIS HEATER MUST BE INSTALLED AND MAINTAINED

BY A QUALIFIED SERVICE AGENCY.

The installation and repair of this appliance must be

done by a qualified service person. Failure to properly

install and maintain this heater could result in an

unsafe or hazardous installation, which may result in a

fire, explosion, property damage, personal injury or loss

of life.

This appliance should be inspected before use and at

least annually. More frequent cleaning may be

required due to excessive lint from carpeting, bedding

material, etc. It is imperative that control compart-

ments, burners, and circulating air passageways of the

appliance be kept clean.

THIS APPLIANCE MUST NOT BE CONNECTED TO A

CHIMNEY OR FLUE SERVING ANY OTHER APPLIANCE.

The installation must conform to local codes. Your

local Jøtul dealer can assist you in determining what is

required in your area for a safe and legal installation.

Some areas require a permit to install a gas burning

appliance. Always consult your local building inspec-

tor, or authority having jurisdiction, to determine what

regulations apply in your area.

NOTE: Your local officials have final authority in

determining if a proposed installation is acceptable.

Any requirement that is requested by the local author-

ity having jurisdiction, that is not specifically ad-

dressed in THIS manual, defaults to local code. In the

absence of local codes, the installation requirements

must comply with the current National codes. In the

U.S., these requirements are established in the Na-

tional Fuel Code, ANSI Z223.1.(NFPA 54). In Canada, the

codes have been established in CAN/CGA B149 Fuel

Installation Code.

Installer l’appareil selon les codes ou reglements

locaux, ou, en l’absence de tels reglements, selon les

Codes d’installation CAN/CGA-B149.

DO NOT OPERATE THIS STOVE IF ANY PART HAS BEEN

UNDER WATER. Call a qualified service technician to

inspect the heater and to replace any part of the

control system and any gas control which may have

been under water.

Ne pas se servir de cet appareil s’il a ete’ plonge dans

l’eau, completement ou en partie. Appeler un

technicien qualifie pour inspecter l’appareil et

remplacer toute partie du syste’me de controle et

toute commande qui ont ete plonges dans l’eau.

Stove Setup

Inspect the stove for damage and contact your dealer

immediately if any is found. Check contents of the

Miscellaneous Kit against the lists on p. 4-5. Complete

the installation steps in the following order:

1. Remove the Top Plate.

Simply lift it from the stove body.

2. GF 100 DV II ONLY : Remove the Front Plate.

Slide it straight up to disengage it from the Side

Plates.

3. GF 200 DV II ONLY: Open the Front Doors.

Cut the two cable ties that secure the doors closed.

4. Remove the Glass Panel.

Open the two trunk latches at the top of the firebox

to disengage the Glass Panel Frame. Lift the frame

up and out of its channel. Set it aside, out of the way,

on a soft surface.

5. Install Optional Blower if appropriate.

6. Install Vent System / Air Restriction as appropriate.

7. Install Fuel Conversion / High Altitude Adjustment if

necessary.

8. Plumb gas line to the stove. Leak Test.

9. Install optional Brick Panels.

10. Install Log Set and Ember Stones.

11. Replace Glass Panel. Test Burner and adjust air

shutter if necessary.

12. Replace Front Panel and Top Plate.

13. Install optional Remote Control or Thermostat.

Suggested Tools for

Installation and Service

• External regulator (for Propane only)

• Piping which complies with local code

• Manual shut-off valve (T-Handle in Massachusetts)

• Sediment trap - if required by code

• Tee joint

• Pipe wrench

• Pipe sealant

• 10 mm open end wrench

• 1/2”, 7/16” open end wrench or deep socket

• Phillips head screwdriver

• Flat head screwdriver

• 1/4” nut driver

• 4 mm allen wrench

• Gloves

• Safety glasses

• Torx T20 screwdriver

• Leak test solution

• Reciprocating Saw

• Power Drill

Location

In selecting a location for the stove, consider the

following points:

1) Heat distribution

2) Vent termination requirements

3) Gas supply line routing

4) Traffic areas, furniture, draperies, etc.

The stove may be located on or near conventional

construction materials, however, proper clearance to

combustibles must be maintained in order to provide

adequate air circulation around the appliance. Also, it

is important to provide adequate access around the

stove for servicing and proper operation.

The clearance and hearth specifications listed in

this manual are the minimum requirements for

combustible material. A combustible material is

anything that can burn (i.e. sheet rock, wall paper,

wood, fabrics etc.). These surfaces are not limited to

those that are visible and also include materials that

may be located behind non-combustibles.

If you are not sure of the combustible nature of a

material, consult your local fire officials. Remember,

“Fire Resistant” materials are considered combus-

tible: they are difficult to ignite, but will burn. Also,

“fire-rated” sheet rock is considered combustible.

Hearth Requirements

This stove should not be installed directly on carpet-

ing, vinyl, linoleum or Pergo®.

If the appliance will be installed on any combus-

tible material OTHER THAN WOOD, a floor pad must

be installed that is either metal, wood, tile, stone, or a

listed hearth pad. This floor protection must extend

the full width and depth of the appliance. It is not

necessary to remove carpeting, vinyl or linoleum

from underneath the floor protection. See fig. 1.

Safety Information

Your stove will reach high surface temperatures

during normal operation. Please note the following

cautionary information.

Due to the high operating temperatures, this

appliance should be located out of traffic areas

and away from furniture and draperies.

Children and adults should be alerted to the

hazards of high surface temperatures and

should stay away to avoid burns and/or clothing

ignition.

Young children should be supervised while they

are in the same room as the gas stove.

Clothing or other flammable materials should

not be placed ON or NEAR the stove. Surveiller

les enfants. Garder les vetements, les meubles,

l’essence ou autres liquides a vapeur

inflammables loin de l’appareil.

NEVER store or use gasoline or any other flam-

mable vapors or liquids in the vicinity of the

stove.

Never burn any other materials in your gas stove,

it is strictly designed for use with natural gas or

propane fuel ONLY.

Any safety screen, glass or guard removed for

servicing the appliance must be replaced prior to

operating the appliance.

Glass Front

Do not operate the this appliance if the glass panel has

been removed, cracked, or broken. Replacement of the

glass should be done by a licensed or qualified service

person. Only remove glass for routine service. Always

handle glass carefully.

Figure 1. Suggested hearth dimensions shown are

slightly larger than the minimum requirement.

24”

(609 mm)

18”

(457 mm)

Stove and Vent Clearance

Requirements

Minimum Clearances from the Stove to Combustibles:

Measured from the stove top plate. See figs. 2-4.

For Both Stoves

Rear: 0” (0 mm)

Ceiling: 42” (1066 mm)

Corner: 2” (50 mm)

Sides:3” (76 mm)

Minimum Clearances between Vent Pipe and

Combustible Materials:

Horizontal Run:

Off the top of the pipe 2” (50 mm)

Off the sides and bottom 1” (25 mm)

Vertical Run:

All sides 1” (25 mm)

Figure 3. Mantel Clearances - stove flush with fireplace face.

Figure 4. Mantel Clearances - stove set back into fireplace,

6 1/2” maximum.

Figure 2. Alcove Installation Clearances.

CLEARANCE TO REAR WALL = ZERO (0”)

GF 100 DV

GF 200 DV

Max. Depth

24”

(610mm)

Alcove Installation

Maximum Alcove Depth:24” (610 mm)

Minimum Alcove Width: 34” (864 mm)

Minimum Ceiling Height

from stove top: 42” (1066 mm)

Min. 34”

(864 mm)

Plinth Kit: 23 3/4 in. (603 mm)

Long Legs: 27 in. (686 mm)

Jøtul GF 100 DV II Jøtul GF 200 DV II

Nordic QT Lillehammer

A49 in. (1245 mm) 51 1/2 in. (1308 mm)

B47 1/2 in. (1206 mm) 50 in. (1270 mm)

C46 in. (1168 mm) 48 1/2 in. (1232 mm)

D44 1/2 in. (1130 mm) 47 in. (1194 mm)

E43 in. (1092 mm) 45 1/2 in. (1156 mm)

F17 3/4 in. (451 mm) 17 3/4 in. (451 mm)

G22 1/4 in. (565 mm) 24 3/4 in. (629 mm)

Plinth Kit: 23 3/4 in. (603 mm)

Long Legs: 27 in. (686 mm)

Jøtul GF 100 DV II Jøtul GF 200 DV II

Nordic QT Lillehammer

A50 in. (1270 mm) 52 1/2 in. (1333 mm)

B48 1/2 in. (1232 mm) 51 in. (1295 mm)

C47 in. (1194 mm) 49 1/2 in. (1257 mm)

D45 1/2 in. (1156 mm) 48 in. (1219 mm)

E44 in. (1118 mm) 46 1/2 in. (1181 mm)

F 4 1/4 in. (108 mm) 4 1/4 in. (108 mm)

G22 1/4 in. (565 mm) 24 3/4 in. (629 mm)

11.5

9.5

7.5

5.5

Max. Mantel

Depth

Min. Mantel

Depth

Max. Top Trim

Depth = 1

3.5

ACE

11.5

9.5

7.5

5.5

Max. Mantel

Depth

Min. Mantel

Depth

Max. Top Trim

Depth = 1

3.5

ACE

Max.

6 1/2

SEALANT

Venting Requirements

Both stoves may be installed with a vertical or horizontal

termination and must conform to the configuration

requirements described in this section. This appliance is

approved for use with vent systems from the following

manufacturers:

• Simpson Dura-Vent GS

• American Metal Products (Amerivent)

• Security Chimneys International, Ltd. (Secure Vent)

• Selkirk Metalbestos (Direct Temp)

• Metal-Fab, Inc. (Direct Vent

• Industrial Chimney Corp. (ExcelDirect Vent)

Use parts of one manufacturer only - DO NOT MIX VENT

COMPONENTS FROM DIFFERENT MANUFACTURERS IN

THE SAME SYSTEM.

Installation of any components not manufactured or

approved by Jøtul or failure to meet all clearance require-

ments will void all warranties and could result in property

damage, bodily injury, or serious fire.

The approved vent configurations described in this

manual are derived from extensive testing under con-

trolled laboratory conditions. Gas appliance performance

can be negatively affected by variables present in the

installation environment, i.e: atmospheric pressure,

strong prevailing winds, adjacent structures and trees,

snow accumulation, etc. These conditions should be

taken into consideration by the installer and stove owner

when planning the vent system design.

IMPORTANT

• JOINT SEALING REQUIREMENT:

APPLY A 1/8” BEAD OF

HIGH-TEMPERATURE SEALANT

(SUCH AS MIL-PAC®) TO THE

MALE SECTION OF THE INNER

VENT PIPE. THE CEMENT

SHOULD FORM A SEAL

BETWEEN THE INNER AND

OUTER PIPES.

• NEVER MODIFY ANY

VENTING COMPONENT, OR

USE ANY DAMAGED

VENTING PRODUCT.

• THE GAS APPLIANCE AND

VENT SYSTEM MUST BE VENTED DIRECTLY TO THE

OUTSIDE OF THE BUILDING AND NEVER ATTACHED TO

A CHIMNEY SERVING A SOLID FUEL OR GAS BURNING

APPLIANCE. EACH DIRECT VENT GAS APPLIANCE MUST

HAVE ITS OWN SEPARATE VENT SYSTEM. COMMON

VENT SYSTEMS ARE PROHIBITED.

• IF VENTING SYSTEM IS DISASSEMBLED FOR ANY

REASON, REINSTALL PER THE INSTRUCTIONS PROVIDED

FOR THE INITIAL INSTALLATION.

Intake Air Restriction

You may need to restrict air intake to the burner, depend-

ing on the stove vent configuration. Two Side Restrictor

Plates and one Rear Restrictor Plate are included in the

Miscellaneous Kit for this purpose. Use the following

guidelines to determine the proper restriction, if any, for

your installation.

Horizontal Termination

No air restriction should be necessary. Do not install the

restrictor plates.

Vertical Termination

1. For Any Vertically Terminated Stove - Fig. 5.

Remove the Recirculator Plate from the back of the

Burner Skirt. It is secured by a single sheet metal screw.

2. Optional Restriction - Fig. 6.

A) Termination less than 8 ft. high:

Install Rear Restrictor Plate. Engage the plate with the

two pins on the back of the Burner Skirt.

B) Termination 8 - 15 ft. high:

Install the Side Restrictor Plates,

in addition to the Rear

Restrictor Plate.

The plates are interchangeable.

Engage each plate with the pin on either side of the

Burner Skirt.

Figure 6. Installing the Air Intake Restrictor Plates.

Figure 5. Remove Recirculator Plate.

Recirculator Plate

Rear Restrictor Plate

Side Restrictor Plates

Vertical Vent Termination

The Jøtul GF 100 DV II and Jøtul GF 200 DV II are ap-

proved for vertical venting through a ceiling or to a roof

termination following these guidelines:

The termination should fall within the shaded area of

the grid depicted in fig.7 below.

Maximum Vertical must not exceed 15 ft. (4.57 m)

measured from the top of the stove.

In no case shall any discharge opening on the termi-

nation cap be less than 18” (457 mm) horizontally from

the roof surface. See fig. 8.



In addition the 90° elbow attached to the stove,

vertical vent run may utilize one 90° or two 45°

elbows. Whenever possible use 45° elbows instead of

a 90° elbow as they are less restrictive to exhaust gas

and intake air flow.

Steep roofs, nearby trees, and predominantly windy

conditions can contribute to poor draft and/or pro-

mote down-draft occurrences. Increasing the height

of the vent may alleviate these conditions.

Use approved vent manufacturer’s Wall Straps to

support an offset pipe run at three feet intervals to

avoid excessive stress on the offsets.

A firestop is required at every floor. Firestops are

available from all vent manufacturers. The opening

should be framed to 10" X 10" inside dimension.

Always maintain a minimum 1" clearance from all

sides of the vertical vent system.

Remove the Recirculator Plate from the back of the

Burner Skirt as shown in fig. 5. Determine which Air

Intake Restrictor plates should be used by following

the guidelines on page 9.

• ANY VENTING WITH A VERTICAL RISE MUST

TERMINATE (END) WITHIN THE SHADED AREA.

• MAXIMUM ELBOWS: TWO 90° OR ONE 90°

AND TWO 45°.

• ALWAYS MAINTAIN THE PROPER CLEARANCES

TO COMBUSTIBLES.

Figure 7. Vent Termination Diagram - any termination

must fall within the shaded area dimensions.

Horizontal Overhang

Vertical Wall

Termination

Cap

18.

min.

Lowest Discharge

Opening

18 min.

18.

min.

Figure 8. Minimum vertical termination height and roof

clearance.

15 Ft.

(457.2 cm)

5 Ft.

(152.4 cm)

10 Ft.

(305 cm)

4 Ft.

(121.9 cm)

VERTICAL RUN

HORIZONTAL RUN

Co-linear Vent Installation

This appliance may be vented through a masonry or

Class A prefabricated chimney using a Co-linear Flexible

Vent system approved for use with a solid-fuel burning

fireplace. When installed in the manner described below,

this system can improve the performance of the appli-

ance in cold climate situations, as well as simplify the

vent installation. See fig. 9.

These installation requirements must be followed:

1.1.

1. Prior to the installation the chimney flue must be

thoroughly cleaned and inspected by a qualified

chimney service person.

2.2.

2. In a masonry chimney, a fireclay liner must be present

the entire length of the chimney.

3.3.

3. Prefabricated chimneys must be UL 103 or ULC S-629

listed and have a minimum INSIDE diameter of 6

inches, (150 mm).

4..

. No appliance can be installed into a chimney flue

serving any other appliance of any kind.

5..

.THE AIR INTAKE FLEX PIPE MUST EXTEND BEYOND THE

DAMPER AREA OF THE FIREPLACE. If the intake flex

duct does not extend the full length of the chimney

and connect to both the unit and the termination cap,

A METAL BLOCK OFF PLATE MUST BE CONSTRUCTED

AND INSTALLED ABOVE THE UNIT PRIOR TO THE END

OF THE INTAKE FLEX AND MUST COMPLETELY SEAL

THE CHIMNEY FLUE FROM THE ROOM.

Consult with the local code authority having jurisdic-

tion before proceeding with this type of installation.

Refer to the vent manufacturer’s instructions for

specific installation requirements.

WARNING: FAILURE TO POSITION THE PARTS AND

STOVE IN ACCORDANCE WITH THESE DIAGRAMS OR

FAILURE TO USE ONLY PARTS SPECIFICALLY APPROVED

FOR USE WITH THIS APPLIANCE, MAY RESULT IN PROP-

ERTY DAMAGE OR PERSONAL INJURY. BE SURE TO

MAINTAIN THE PROPER CLEARANCES TO COMBUSTIBLES

AS DEFINED IN THIS MANUAL AND IN THE INSTRUCTIONS

PROVIDED WITH EACH VENT COMPONENT.

Figure 9.

Co-linear Adaptor installed through a masonry chimney.

Figure 10. Simpson Dura-Vent #923GCL Co-linear Adaptor.

GF 100 DV II: A : 16 3/4” B : 20 3/4”

GF 200 DV II: A : 18” B : 22”

Add 2 1/4” with Long Legs.

Subtract 1” with Plinth

Venting Through a Fireplace

Intake Air

Exhaust Gas

High Wind

Cap

Max.

Co-linear

Height 15 ft.

(10.66 m)

Min.

Co-linear

Height 8

ft.

(2.44 m)

Air Intake Flex

pipe must

extend above

the damper.

Sealed

Damper

Max.

Offset 24”

(609 mm)

Figure 12. Corner Installation, Horizontal Termination

directly off rear. Maximum Horizontal run is 2 ft. (610

mm).

Horizontal Vent Termination

Wall Cut-out Opening: A minimum 10" X 10"

(250 mm x 250 mm) square hole is required for proper

pipe clearances through a combustible wall. Use one

of the approved vent manufacturers’ WALL THIMBLE

for the wall penetration.

DO NOT FILL AIR SPACE WITH ANY TYPE OF INSULATION.

The minimum horizontal run made directly off the rear

of the stove into a standard horizontal cap shall be no

less than a 6” (152 mm) vent section. See fig. 11.

The maximum horizontal run made directly off the

rear of the stove into a standard horizontal termina-

tion must not exceed 4 ft. (1219 mm) See fig. 11.

Corner Installation: Max. Horizontal Run is 2 ft. (610

mm). See Fig. 12.

A horizontal termination must fall within the shaded

area illustrated in fig. 7, Vent Termination Diagram.

The horizontal termination cap must maintain a 3"

clearance to any overhead combustible projections

2 1/2" or less. It must also maintain 12" clearance from

projections exceeding 2 1/2". See fig. 14.

Any horizontal run of vent must be level or have a

1/4" rise for every foot of run toward the termination

cap. NEVER ALLOW THE VENTING TO RUN DOWN-

WARD FROM STOVE TO TERMINATION; DOWNWARD

VENT RUNS TRAP HEAT AND CAUSE HIGH TEMPERA-

TURES TO DEVELOP WITHIN THE VENT THAT COULD

START A FIRE.

Install a Vinyl Siding Standoff between the vent

termination and an exterior wall covered by vinyl

siding material to prevent potential heat damage to

the siding.

Do not recess the termination cap into a wall or siding.

Figure 11. Min. / Max. Horizontal Run

Min. 6 in.

Max. 48 in.

Horizontal Run

Zero

Clearance

to Rear

Decorative

Wall Shield

Standard

Horizontal

Termination

Min. 2

51 mm

Min. 2

51 mm

45°

Elbow

Min. 6 (152 mm)

Max. 24 (610 mm)

See Note F

Fig. 17

Wall Thimble

and Trim Collar

Standard

Horizontal

Termination

Cap

Wall Shield Installation

The decorative Wall Shield, included in the Miscellaneous

Hardware bag, is used to obscure the vent hole in the

wall in installations vented directly off the rear of the

stove. Follow this procedure:

1. Remove the top two 1/4” hex head screws from the

rear shroud of the stove.

2. Align the holes in the wall shield with the holes in the

rear shroud.

3. Secure the wall shield to the stove with the two 1/4”

hex head screws. See fig. 16.

Figure 14. Termination Clearance to overhangs

Figure 15.

Wall Shield installation.

3

76 mm

12 

305

2 1/2

64 mm

Figure 13. Horizontal Termination with Vertical Rise.

Wall Thimble

and Trim Collar

Max. 4 ft.

Horizontal

Run

Max. Two

90° Elbows

or One 90°

and Two

45° Elbows

Max. 15 ft.

Vertical Vent

Run

Figure 17. Vent Terminal Clearances - National Fuel Gas Code.

Horizontal Termination Clearance

A = Clearance above grade, veranda, porch , deck, or

balcony : 12 inches (30 cm) minimum.

B = Clearance to window or door that may be

opened: **Min. 9 inches, U.S. / *12 inches (30 cm)

CAN.

We recommend 12in. minimum to prevent con-

densation on the window.

C = Clearance to permanently closed window:

**Min. 9 inches, U.S. / *12 inches (30 cm) CAN

We recommend 12 in. minimum to prevent

condensation on the window.

D = Vertical clearance to ventilated soffit located

above the terminal within a horizontal distance of 2

feet (60 cm) from the centerline of the terminal: 18

inches

(46 cm) minimum.

E = Clearance to unventilated soffit: 12 inches (46

cm) minimum.

F = Clearance to outside corner: **Min. 9 inches, U.S. /

*12 inches (30 cm) CAN. We strongly recommend 12

inches, particularly where windy conditions pevail.

G = Clearance to inside corner: ** Min. 6 inches, U.S. /

*12 inches (30 cm) CAN. We strongly recommend 12

inches, particularly where windy conditions pevail.

* In accordance with CSA B149.1 Installation Codes.

** In accordance with the current ANSI Z223.1/NFFPA 54,

National Fuel Gas Code. Note: Local Codes and Regulations

may require different clearances.

1 A vent shall not terminate directly above a sidewalk or

driveway which is located between two single family

dwellings and serves both dwellings.

2Only permitted if veranda, porch, deck, or balcony, is

fully open on a minimum of two sides beneath the floor.*

H = *Not to be installed within 15 feet (4.5 m) above a

meter/regulator assembly within 3 feet (90 cm)

horizontally from the center-line of the regulator.

I = Clearance to service regulator vent outlet:

3 feet (91 cm) minimum.

J = Clearance to nonmechanical air supply inlet to

building or the combustion air inlet to any other

appliance:

12 inches (30 cm) minimum.

K = Clearance to a mechanical air supply inlet:

**Min. 3 feet (91 cm) above if within 10 feet horizon-

tally, U.S. / *6 feet (1.83 m) minimum / CAN

L = 1 Clearance above paved sidewalk or a paved driveway

located on public property: 7 feet (2.1 m) min.

M = Clearance under veranda, porch, deck, or balcony:

12 inches (30 cm) minimum. 2

Tools required:

• 1/2” open ended wrench or deep-well socket, Torx T20

or slotted screwdriver, 4 mm allen wrench.

Conversion Kit Contents:

• 1, regulator tower labeled for propane

• 3, regulator tower screws

•1, burner orifice (GF 100: #48 for NG, #56 for LP)

(GF 200: #46 for NG, 1.20 mm for LP)

• 1, pilot orifice (#51 for NG, #30 for LP)

• Label A - to be completed and applied to

the back of the stove

• Label B - apply to the stove’s Rating Plate

• Small valve label - apply to valve body

Conversion instructions are also shipped in the stove

with the conversion kit.

Mobile Home Installation

These appliances can be installed for use in a mobile

home in the U.S. and Canada provided:

1.1.

1. The stove is secured to the floor of the mobile home.

Use the Jøtul Floor Bracket Kit appropriate for your

stove’s leg; see the Accessories listing on p. 29.

2.2.

2. Provision must be made to secure an electrical ground

between the stove and the mobile home chassis.

3.3.

3. The stove is installed in accordance with Title 24 CFR,

Part 3280- Manufactured Home Construction and

Safety Standard, in the U.S. In Canada, comply with

CSA Z240.4, Gas Equipped Recreational Vehicles and

Mobile Housing.

4..

. Always contact your local officials about installation

restrictions and requirements in your area.

THIS APPLIANCE MAY BE INSTALLED AS AN OEM INSTALLA-

TION IN A MANUFACTURED (MOBILE) HOME AND MUST BE

INSTALLED IN ACCORDANCE WITH THE MANUFACTURER’S

INSTRUCTIONS AND THE MANUFACTURED HOME CON-

STRUCTION AND SAFETY STANDARD, TITLE 24 CFR, PART

3280. THIS APPLIANCE IS ONLY FOR USE WITH THE TYPE OF

GAS THAT IS INDICATED ON THE STOVE’S RATING PLATE. A

GAS CONVERSION KIT IS PROVIDED WITH THE NORDIC QT

DIRECT VENT GAS STOVE.

THIS APPLIANCE MAY BE INSTALLED IN AN AFTERMARKET

PERMANENTLY LOCATED, MANUFACTURED (MOBILE) HOME,

WHERE NOT PROHIBITED BY LOCAL CODES.

CET APPAREIL PEUT ETRE INSTALLE DANS UN MAISON

PREFABRIQUEE (MOBILE) DEJA INSTALLEE A DEMEURE SI LES

REGLEMENTS LOCAUX LE PERMETTENT. CET APPAREIL DOIT

ETRE UTILISE UNIQUEMENT AVEC LES TYPES DE GAS

INDIQUES SUR LA PLAQUE SIGNALETIQUE. NE PAS

L’UTILISER AVEC D’AUTRES GAS SAUF SI UN KITDE CONVER-

SION CERTIFIE EST INSTALLE.

Fuel Conversion

Your gas stove is shipped from the factory equipped to

burn NATURAL GAS only. If PROPANE gas is to be used as

fuel, the appliance must first be converted for use with

propane.

Jøtul GF100 DV II Nordic QT::

: Use Propane Conversion Kit

155628, supplied with the appliance.

Jøtul GF200 DV II Lillehammer: Use Propane Conversion

Kit 155626, supplied with the appliance.

WARNING:

THE CONVERSION KIT IS TO BE INSTALLED BY AN

AUTHORIZED JØTUL SERVICE TECHNICIAN IN

ACCORDANCE WITH THE MANUFACTURER’S

INSTRUCTION AND ALL CODES AND REQUIREMENTS

OF THE AUTHORITY HAVING JURISDICTION. FAILURE

TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN

SERIOUS INJURY OR PROPERTY DAMAGE. THE

QUALIFIED AGENCY PERFORMING THIS WORK

ASSUMES RESPONSIBILITY FOR THIS CONVERSION.

IN CANADA:

THE CONVERSION SHALL BE CARRIED OUT IN ACCOR-

DANCE WITH THE REQUIREMENTS OF THE PROVIN-

CIAL AUTHORITIES HAVING JURISDICTION AND IN

ACCORDANCE WITH THE REQUIREMENTS OF THE

CAN1-B149.1 AND .2 INSTALLATION CODE.

Gas Conversion Procedure

1. Turn off gas supply to stove.

2. Remove the stove Top Plate (3).

3. GF 100 DV II Only: Remove the front plate from the

stove. Pull the casting straight up and out away from

the side panels. Pull the panel upward with one hand

while the other pushes against the top of the firebox.

4. Release the trunk latches at the top of the firebox.

Carefully lift the glass frame up and out.

5. Remove the Log Set using care not to scratch or dam-

age logs.

6. Remove the burner skirt. Using one hand, lift from

under the rear lip and let the skirt rotate vertically.

Then rotate counterclockwise to clear the firebox

opening as shown in fig. 18.

7. Change the Main Burner Orifice. Fig. 19. Using a ½”

open ended wrench or deep-well socket remove the

burner orifice and replace with the appropriate orifice

supplied in the kit.

GF 100 DV II - #48 for NG #56 for LP

GF 200 DV II - #46 for NG 1.20 mm for LP

8 CHANGE THE PILOT ORIFICE: From within the firebox,

remove the Pilot Head by pulling it straight up from the

pilot base. See fig. 20.

Using the 4 mm allen wrench that is included with the

conversion kit, unscrew the pilot orifice (counterclock-

wise). Replace with the appropriate orifice:

#51 for natural gas

#30 for propane gas

9. Tighten orifice into the base of the pilot assembly. To

prevent bypass leaks, be sure the orifice is secured

tightly and flush with the base. Replace pilot head by

pushing it down onto the pilot base. See fig. 20.

10. Replace the Variable Regulator. Using a Torx T-20

screwdriver, remove the three specialty screws from the

front of the valve regulator. See fig. 21.

11. Remove the Regulator Tower, Gasket, white plastic disk,

and Spring. Discard these parts.

12. Install the new variable regulator tower being sure that

the gasket is properly positioned and tighten screws

securely.

13. Install the identification labels to the stove so that they

can be seen by any person that may be servicing the

stove.

Label A: apply to back of stove.

Label B: apply to stove’s rating plate.

Small valve Label: apply to valve.

14.Reassemble the stove. NOTE: Correct Burner position is

critical to proper function. Be certain that the burner

plate is securely engaged with the support legs in the

bottom of the firebox. When seated correctly, the

burner plate will be level, with little or now lateral

movement. The pilot head should protrude up above

the surface of the burner plate. See figure 22.

15. Apply gas to the system and check for leaks using a

soapy water solution or electronic gas detector.

NEVER USE AN OPEN FLAME TO CHECK FOR GAS

LEAKS.

Correct gas pressure is essential for efficient and safe

operation of this appliance. Correct gas pressure must

be established at the time of installation.

NOTE: Minimum LP Inlet pressure is 12.0 w.c.

For more details, see the Gas Pressure section of this

manual (page 17).

ALWAYS REFER TO THE LIGHTING INSTRUCTIONS ON

THE INSIDE BACK COVER OF THIS MANUAL WHEN

LIGHTING THE STOVE.

16. Adjust the Air Shutter: Locate and loosen the wingnut

that secures the Air Shutter. See fig. 26. It is under the

stove, in the center toward the rear. Push the shutter

stem back to restrict air and forward to increase air to

the burner. You will need to experiment to find the

best setting for your particular installation. The

shutter is set at the halfway position at the factory.

Be sure to tighten the wingnut on the Air Shutter stem

snugly after any adjustment. This ensures that the

burner remains locked in place.

Figure 18.

Remove the Burner

Skirt from the stove.

Figure 19.

Burner orifice

and pilot

assembly

locations.

Orifice

Air Shutter

Pilot

Assembly

Regulator

Towe r

Gasket

Apply small

label

Mounting

Screws

Gas Supply Connection

NONO

NOTT

TE:E:

E:E:

E: If If

If If

If the optional Blothe optional Blo

the optional Blothe optional Blo

the optional Bloww

wer will be installed,er will be installed,

er will be installed,er will be installed,

er will be installed, use a use a

use a use a

use a

9090

90° Elbo° Elbo

° Elbo° Elbo

° Elbow ow o

w ow o

w off

ff f

f f

f the vthe v

the vthe v

the valvalv

alvalv

alve e

e e

e tt

to cro cr

o cro cr

o creaea

eaea

eate adequate adequa

te adequate adequa

te adequate clearte clear

te clearte clear

te clearancanc

ancanc

ancee

for or

or or

or the main gthe main g

the main gthe main g

the main gas lineas line

as lineas line

as line..

The gas supply line connection is made to the valve just

inside the left rear leg. The gas supply line should be 3/8"

npt with a 1/2" diameter supply, or the appropriate size to

provide sufficient gas pressure to the valve regardless of

the input setting.

The use of a Flexible Gas Appliance Connector is

acceptable in many areas in the U.S. However, Canadian

methods vary depending on local code.

ALL INSTALLATIONS MUST COMPLY WITH LOCAL CODE

OR IN THE ABSENCE OF LOCAL CODE, MUST COMPLY

WITH THE MOST RECENT EDITION OF THE NATIONAL

FUEL GAS CODE ANSI Z223.1/NFPA 54 OR CAN-B149.

All codes require a gas shut-off valve (gas cock) and

union, to be installed in the supply line, and in the same

room as the appliance. This allows for the disconnection

of the stove for servicing and maintenance. See fig. 23.

Figure 23.

Supply

valve

coupling.

Leak test:

1. Use an electronic gas detector, or mix a 50-50 solution of

water and dish soap.

2. Light appliance- see lighting instructions on the inside

back cover of this manual or on the stove’s rating plate.

3. Brush or spray all joints and connections with the soapy

water solution.

4. If bubbles appear at any connection or seam or a gas

odor is detected, immediately turn gas control knob to

the OFF position.

5. Tighten or reconnect the leaking joint and retest for any

gas leaks.

1/2 x 3/8 Flare

Shut-off Valve

3/8 Flex Tubing

3/8 NPT x 3/8

Flare Fitting

3/8Nipple

Gas Stub

1/2 x 3/8

Reducer

3/8 Shut-off

Valve

3/8 Close Nipple

3/8 Union

Orifice

Pilot Base

Pilot Head

Figure 20.

Pilot orifice removal and replacement.

A T-HANDLE GAS COCK IS REQUIRED IN

MASSACHUSETTS TO COMPLY WITH CODE 248CMR.

Secure all joints tightly using appropriate tools and

sealing compounds. For propane units be sure to use

compounds that are propane resistant. Turn on gas supply

and test for gas leaks using a soapy water solution. Never

use an open flame to check for leaks.

Figure 22.

Check burner plate / pilot head alignment. Burner is

secure, and level. The pilot head protrudes above the

burner surface.

Figure 21. Regulator Assembly.

Retainer

Clip

Pilot Head

Burner

Plate

Gas Pressure

Correct gas pressure is essential for efficient and safe

operation. It is important that the correct pressure is

established at the time of the installation. Proper gas

pressure provides a consistent flow of gas to the appli-

ance and is instrumental in checking for gas leaks.

Pressure Test: Attach a manometer to the appropriate

test point on the valve. See fig. 24. The gauge connections

are located on the front of the valve under the On/Off/

Pilot- knob. Gauge connections are identified by:

E - for Inlet or Supply Pressure (the amount of gas

coming to the valve.)

A - for Manifold Pressure (the amount of gas that is

coming out of the valve to the burner.)

ALWAYS TEST PRESSURES WITH VALVE CONTROL KNOB

SET ON HIGH.

High Altitude Adjustment

The decreased atmospheric pressure of higher altitudes

affects heat value of gaseous fuels. Most gas suppliers

derate the gas intended for use at elevations above 2000

feet. Check with your gas supplier before performing

derate adjustment to the burner.

The GF 100 DV II Nordic QT does not require adjustment

for elevations up to 4500 ft. DO NOT DERATE.

The GF 200 DV II Lillehammer may be adjusted for

altitude over 2000 ft. (610 - 1371 m). Check with your gas

supplier and, if necessary, install High Altitude Adjust-

ment Kit 155808 for Natural Gas, or Kit 155809 for

Propane.

See the chart below for appropriate orifice sizes and

part numbers.

IN THE U.S:

THE DERATING KIT MUST BE INSTALLED BY AN AUTHORIZED

SERVICE TECHNICIAN IN ACCORDANCE WITH THE

MANUFACTURER’S INSTRUCTIONS AND ALL CODES AND

REQUIREMENTS OF THE AUTHORITY HAVING JURISDICTION.

THE INFORMATION LABEL MUST BE FILLED OUT BY THE

INSTALLER AND APPLIED TO THE APPLIANCE AT THE TIME OF

THE CONVERSION. THE QUALIFIED SERVICE AGENCY

PERFORMING THIS WORK ASSUMES RESPONSIBILITY FOR

THIS DERATING.

IN CANADA,

THIS UNIT HAS BEEN TESTED FOR INSTALLATION AT HIGH

ALTITUDES IN ACCORDANCE WITH CANADIAN TEST STAN-

DARD CAN/CGA-2.17.

THE DERATING SHALL BE CARRIED OUT IN ACCORDANCE

WITH THE REQUIREMENTS OF THE PROVINCIAL AUTHORI-

TIES HAVING JURISDICTION AND IN ACCORDANCE WITH

THE REQUIREMENTS OF THE CAN1-B-149.1 AND .2 INSTALLA-

TION CODE.

For high altitude installations, consult your local gas

distributor or the authority having jurisdiction for proper

rating methods. If the appliance is converted for high

altitude, the Conversion Label, supplied with the kit, must

be filled out by the installer and applied to the appliance

at the time of the conversion. See fig. 25.

NECESSARY INLET GAS PRESSURES

(inches water column)

MIN MAX

NATURAL GAS 5.0 7.0

PROPANE 12.0 14.5

The appliance and its appliance main gas valve must

be disconnected from the gas supply piping system

during any pressure testing on that system at test

pressures in excess of 1/2 psig (3.5 kPa).

The appliance must be isolated from the gas supply

line by closing its individual manual gas shut-off valve

(gas cock) during any pressure testing of the gas supply

piping system that is equal to or less than pressures of

1/2 psig (3.5 kPa).

MANIFOLD PRESSURES

(inches water column)

MIN MAX

NATURAL GAS 1.2 3.8

PROPANE 2.9 11.0

Figure 24. Pressure test points.

Flame Appearance -

Air Shutter Adjustment

WARNING: AIR SHUTTER ADJUSTMENTS SHOULD ONLY BE

PERFORMED BY A QUALIFIED PROFESSIONAL SERVICE

TECHNICIAN.

The air shutter setting at the burner orifice can be ad-

justed to achieve the desired flame appearance. The

shutter is set in the mid-range at the factory, however, you

will want to adjust it if a fuel conversion kit has been

installed or if the flame pattern is not as desired. The

adjustment stem is located under the firebox, directly

behind the gas control valve. Generally, flame appearance

is a matter of preference, however most people enjoy a

warm yellowish flame.

Too much air - the appliance will generate a flame

that is blue and transparent, or an “anemic” flame.

Not enough air - the burner will generate very long

yellow flames resulting in soot. Sooting produces black

deposits on the logs, on the inside walls of the appliance,

and potentially on the exterior termination cap.

Sooting is caused by incomplete combustion in the

flames and lack of combustion air entering the air shutter

opening. Open the shutter setting to allow more air.

To adjust the air shutter:

1. Locate and loosen the adjustment stem wingnut

protruding from the bottom of the firebox, directly

behind the gas valve. See fig. 26.

2. Push the stem back to decrease air, or pull it forward to

increase air. Make adjustments in small increments

(1/8”) and allow the burner to “ settle in” for a few

minutes before making another one. Small shutter

adjustments can produce dramatic changes to flame

characteristics.

4. Re-tighten the wing nut when the desired flame

appearance has been achieved.

Figure 26.

Air Shutter adjustment

Derating Procedure:

1. To derate this unit, install the appropriate orifice per

the High Altitude chart.

2. Remove the Burner Skirt and Burner Plate to expose

the main burner orifice.

3. Using a 1/2” open ended wrench or a deep-well socket

remove the burner orifice.

4. Replace with the appropriate orifice from the high

altitude kit.

5. Be sure to apply the high altitude conversion label

provided to the rating plate on the appliance.

THIS STOVE HAS BEEN CONVERTED FOR USE AT AN

ALTITUDE OF: ________________

Orifice Size: ____________ Manifold Press. _____

Input Btu/Hr. ___________ Fuel Type __________

Date of Conversion ___________

Figure 25. This label must be filled out and applied to the

appliance by the installer.

High Altitude Orifice Chart

Jøtul GF 200 DV II Only

Elevation Fuel Part No.

0 - 2000 ft. Natural Gas #46 220975

(0 - 610 m) Propane 1.20 mm 221185

2001 - 4500 ft. Natural Gas #47 220976

(611 - 1370 m) Propane #56 129466

Orifice

Size

OPEN CLOSE

Optional Wall Thermostat or

Remote Control

Use only a 750 millivolt DC two-wire circuit thermostat

with this appliance. The thermostat should be placed in

the same room as the heater, typically 5 feet off the

floor. Avoid drafty areas or any area that may affect the

accuracy of the thermostat.

The thermostat should be connected to the Nordic

QT using a minimum of 16 gauge wire with a maximum

length of 35 feet of wire.

Connect the two thermostat wire leads to the two

lower terminals on the terminal block located directly to

the right of the valve. Do not overtighten the connec-

tions. IT IS NOT NECESSARY TO DISCONNECT ANY OTHER

WIRES. See Fig. 27.

For thermostatic operation, the On/Off/T-Stat

switch on the back of the stove must be in the T-stat

position, and the pilot light must be running, as it is the

power source for the thermostat.

At the thermostat, the two wires should be con-

nected to the two connection screws on the thermostat

base plate per the manufacturer’s instructions.

Remote Control

When using a remote, the remote receiver should be

wired to the terminal block the same way the thermo-

stat would be. See the instructions above.

Follow the operating instructions included with the

Remote Control unit.

CAUTION:

LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN

SERVICING THE CONTROLS. WIRING ERRORS CAN CAUSE

IMPROPER OR DANGEROUS OPERATION. ALWAYS VERIFY

PROPER OPERATION AFTER SERVICING THE APPLIANCE.

Log Set Installation

NOTE: Install the optional Brick Kit, if appropriate, before

installing the Log Set. See page 30.

The Log Set and Ember Stones are packaged in foam

inside the firebox. Wear gloves to prevent skin irritation

from the ceramic fibers.

1. Assemble the Left and Right Rear Logs as shown in

fig 28. First engage the halves together, and then

engage the pins on the burner skirt with the adjacent

holes in the underside of the logs.

2. Locate the Middle Log as shown in fig. 29.

3. Also included is a bag of ember stones that simulate

glowing coals when the burner is operating. These

should be spread thinly over the burner plate.

NOTE: Keep the ember stones 1/4” away from the edge

of the Burner Skirt an d Pilot Assembly. See fig. 29.

All the ember stones do not have to be used.

Figure 27. Accessory wiring diagram.

Figure 28.

Install

Rear Log.

TERMINAL

BLOCK

VALVE

THERMOPILE

OPTIONAL

THERMOSTAT

REMOTE

CONTROL

ROCKER

SWITCH

OFF

STAT

Figure 29. Middle Log and ember stones in place.

1/4

6 mm

1/4

6 mm

Pilot

Assembly

KEEP EMBER STONES

FROM OBSTRUCTING

PILOT AREA.

La page charge ...

Jøtul GF 200 DV II Lillehammer Installation And Operation Instructions Manual

Marque: Jøtul

Modèle: GF 200 DV II Lillehammer

Catégorie: Cheminées

Taper: Installation And Operation Instructions Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Jøtul GF 200 DV II Lillehammer

Jøtul GF 200 DV II Lillehammer Installation And Operation Instructions Manual

Jøtul GF 200 DV II Lillehammer Installation And Operation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents