Allen + Roth 2416658 Manuel utilisateur

welcoming • sophisticated • inspiring

1

ITEM #2416658

ELECTRIC FIREPLACE

TV STAND

MODEL #2267FM-28-201

Français p. 19

Español p. 37

allen + roth

®

is a trademark or registered trademark of LF,

ATTACH YOUR RECEIPT HERE

Serial Number__________________ Purchase Date__________________

Questions, problems, missing parts? Before returning to your retailer, call our customer service

department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

VR20055

2

TABLE OF CONTENTS

Package Contents ............................................................................................................................... 3

Hardware Contents.............................................................................................................................. 4

Safety Information ............................................................................................................................... 4

Preparation .......................................................................................................................................... 8

Assembly Instructions.......................................................................................................................... 8

Corner Assembly (Optional) ...............................................................................................................11

Change Door Panel (Optional) .......................................................................................................... 12

Operating Instructions ....................................................................................................................... 13

Care And Maintenance ...................................................................................................................... 15

Troubleshooting ................................................................................................................................. 16

One-Year Limited Warranty ............................................................................................................... 17

Replacement Parts List ..................................................................................................................... 18

3

PACKAGE CONTENTS

B

A

I

C

E

D

K

J

F

M

N

O

L

G

H

P

PART DESCRIPTION QUANTITY

A Top 1

B Corner Panel 1

C Left Wall 1

D Right Wall 1

E Left Front Panel 1

F Right Front Panel 1

G Center Panel 1

H

Wood Door Panel

(Optional)

1

I L Corner Support Rod 1

J Base And Heater 1

PART DESCRIPTION QUANTITY

K Fireplace Brick Wall 1

L Fireplace Glass Front 1

M Fire Log 1

N Fireplace Grate 1

O

Remote Control

(Battery Inside)

1

P Panel 1

4

HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)

AA BB CC DD EE FF

PART DESCRIPTION QUANTITY

AA

Long Bolt

25

BB

Washer

25

CC

Wooden Dowel

18

DD

Touch-up Pen

1

EE

Screw

6

FF

L-Bracket

2

SAFETY INFORMATION

Please read and understand this entire manual before

attempting to assemble, operate or install the product.

This equipment has been tested and found to comply

with the limits for Class B digital devices, pursuant to

Part 15 of the FCC rules. These limits are designed

to provide reasonable protection against harmful

interference in a residential installation. The equipment

generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance

with the instructions, may cause harmful interference

to radio or television reception, which can be

determined by turning the equipment off and on. The

user is encouraged to try and correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and

the receiver

• Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference,

and

2. This device must accept any interference received,

including interference that may cause undesired

operation.

5

SAFETY INFORMATION (CONT'D)

Modiﬁcations not approved by the party responsible

for compliance could void user’s authority to operate

the equipment.

This Class B digital apparatus complies with Canadian

ICES-003.

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions

should always be followed to reduce the risk of ﬁre,

electric shock and injury to persons, including the

following:

DANGER

• To reduce the electrical shock, tipping and instability

of the product.

• Read all instructions before installing or using this

heater.

• If the information in this manual is not followed

exactly, an electric shock or ﬁre may result causing

property damage, personal injury or loss of life.

• ALWAYS unplug this appliance/furnishing from the

electrical outlet before cleaning or servicing.

• This product is intended to ﬁt most plasma and

LCD televisions (up to 56 inches and weighing a

maximum of 80 pounds). Using this item with loads

heavier than the stated maximum can result in

tipping and/or instability, which can result in injury or

even death.

WARNING

• Risk of death or serious injury may occur when

children climb on audio and/or video equipment

furniture. A remote control or toys placed on the

furnishing and as a result the furnishing may tip

over on the child.

• Risk of death or serious injury may occur.

Relocating audio and/or video equipmentto furniture

not speciﬁcally designed to support audio and/or

video quipment may result in death or serious injury

due to the furnishing collapsing or over turning onto

a child.

• This appliance is hot when in use. To avoid burns,

DO NOT let bare skin touch hot surfaces. Keep

combustible material, such as furniture, pillows,

bedding, papers, clothes and curtains at least 3 feet

from this appliance and keep them away from the

sides and rear.

• Extreme caution is necessary when any heater

is used by or near children or individuals with

disabilities and whenever the ﬁreplace is left

operating and unattended.

• DO NOT run cord under carpeting. DO NOT cover

cord with throw rugs, runners, or similar coverings.

• DO NOT route cord under furniture or appliances.

Arrange cord away from trafﬁc areas and where it

will not be tripped over.

• DO NOT insert or allow foreign objects to enter any

ventilation or exhaust opening as this may cause

an electric shock or ﬁre, or damage the appliance.

• This appliance has hot and arcing or sparking parts

inside. DO NOT use it in areas where gasoline,

paint or ﬂammable vapors or liquids are used or

stored. This ﬁreplace should not be used as a

drying rack for clothing. Christmas stockings or

decorations should not be hung in the area of it.

• Use this appliance only as described in the manual.

Any other use is NOT recommended by the

manufacturer and may cause ﬁre, electric shock or

injury to persons.

• Reduce the risk of burns, ﬁre, electrical shock, or

injury to persons:

• Unplug from outlet before putting on or taking off

parts.

• Close supervision is necessary when this furnishing

is used by, or near children, invalids, or disable

persons.

• Use this furnishing only for its instended use

as described in these instructions. DO NOT

use attachments not recommended by the

manufacturer.

• Keep the cord away from heated surfaces.

• Never operate the furnishing with the air openings

blocked. Keep the air openings free of lint, hair, and

the like.

• Never drop or insert any onject into any opening.

• DO NOT operate where aerosol (spray) products

are being used or where oxygen is being

administered.

• To disconnect, turn all controls to the off position,

then remove plug from outlet.

• Each surface intended to support a load shall have

a cor responding statement in the use instructions

specifying the maximum intended load for that

surface in pounds (kilograms).

• Risk of electric shock-connect this furnishing to

a properly grounded outletonly. See Grounding

Instructions.

6

SAFETY INFORMATION (CONT'D)

• Risk of electric shock, ﬁre and injury-review the

assembly instrustion to conﬁrm that the appropriate

critical components and accessories are being used

with the furnishing.

CAUTION

• DO NOT operate any heater with a damaged

cord or plug or after the heater malfunctions. DO

NOT operate any heater if it has been dropped

or damaged in any manner. Disconnect power

at service panel and have heater inspected by a

reputable electrician before reusing.

• Any repairs to this ﬁreplace should be carried out by

a qualiﬁed service person.

• Under no circumstances should this ﬁreplace be

modiﬁed. Parts having to be removed for servicing

must be replaced prior to operating this ﬁreplace

again.

• Household use only.

• DO NOT use outdoors.

• “WARNING – Death or serious injury may occur

when children climb on audio and/or video

equipment furniture. A remote control or toys placed

on the furnishing may encourage a child to climb on

the furnishing and as a result the furnishing may tip

over on to the child”.

• “WARNING – Relocating audio and/or video

equipment to furniture not speciﬁcally designed to

support audio and/or video equipment may result

in death or serious injury due to the furnishing

collapsing or over turning onto a child”.

• This heater is not intended for use in bathrooms,

laundry areas and similar indoor locations. NEVER

place heater where it may fall into a bathtub or other

water container.

• To disconnect this appliance, turn controls to the

OFF position, then remove plug from outlet.

• ONLY connect to properly grounded outlets.

• This appliance, when installed, must be electrically

grounded in accordance with local codes, with the

current CSA C22.1 Canadian Electrical Code or

follow U.S.A. Installations, follow local codes and

the National Electrical Code, ANSI/NFPA N0.70.

• To prevent a possible ﬁre, DO NOT block air intakes

or exhaust in any manner. DO NOT use on soft

surfaces, like a bed, where opening may become

blocked.

• The heaters MUST NOT be located immediately

below a socket-outlet.

• ALWAYS plug heaters directly into a wall outlet /

receptacle. NEVER use with an extension cord or

re-loadable power tap (outlet / power strip).

• DO NOT slide insert on top of wood to avoid

scratching wood surface.

• DO NOT place any object on top of the insert or

block the air intakes / vents as this can cause the

unit to overheat and could cause a ﬁre.

7

SAFETY INFORMATION (CONT'D)

Electrical Connection

• A 15-Amp, 120-volt, 60 Hz circuit with a properly

grounded outlet is required. Preferably, the ﬁreplace

will be on a dedicated circuit as other appliances

on the same circuit may cause the circuit breaker

to trip or the fuse to blow when the heater is in

operation. The unit comes standard with 6-ft. three-

wire cord, exiting from the rear of the ﬁreplace. DO

NOT exceed the current rating of the current tap.

Grounding Instructions

• This heater is for use on 120 volt. The cord has a

plug as shown below. See illustration or grounding

instruction. An adapter as shown at C is available

for connecting three-blade grounding type plugs

to two-slot receptacles. The green grounding plug

extending from the adapter must be connected to

a permanent ground such as a properly grounded

outlet box. The adapter should not be used if a

three-slot grounded receptacle is available.

A B C

Grounding Pin

Grounding Means

Metal

Screw

Cover of

Grounding

Box

Adapter

SAVE THESE INSTRUCTIONS

8

PREPARATION

Before beginning assembly of product, make sure

all parts are present. Compare parts with package

contents list and hardware contents list. If any part is

missing or damaged, do not attempt to assemble the

product.

Estimated Assembly Time: 50 minutes

Tools Required for Assembly (not

included): Phillips screwdriver

ASSEMBLY INSTRUCTIONS

1. From behind the assembly, align the holes on

left front panel (E) with the corresponding holes

on left wall (C). securing with two washers (BB)

and two long bolts (AA).

Repeat for right wall (D)

Hardware Used

AA

Long Bolt

x 4

BB

Washer

x 4

1

F

E

C

BB

AA

D

2. Insert four wooden dowels (CC) into holes on left

outer side of base (J). Place assembly from Step

1 onto base (J), securing with three washers

(BB) and three long bolts (AA).

Repeat for right wall (D).

Hardware Used

AA

Long Bolt

x 6

BB

Washer

x 6

CC

Wooden Dowel

x 8

CC

BB

AA

1

J

2

9

ASSEMBLY INSTRUCTIONS (CONT’D)

3. Insert two wooden dowels (CC) into the top

middle holes on both left front panel (E) and right

front panel (F). Carefully position the center

panel (G) into place between left front panel (E)

and right front panel (F). Secure each side with

one washer (BB) and one long bolt (AA).

Hardware Used

AA

Long Bolt

x 2

BB

Washer

x 2

CC

Wooden Dowel

x 2

G

F

E

CC

BB

AA

1

3

2

4. Insert two wooden dowels (CC) into the top

outer holes on both left wall (C) and right wall

(D). Attach top (A), securing from underneath

with seven washers (BB) and seven long bolts

(AA).

Hardware Used

AA

Long Bolt

x 7

BB

Washer

x 7

CC

Wooden Dowel

x 4

A

D

C

CC

BB

AA

1

4

2

5. From behind the assembly, attach the ﬁreplace glass

front (L), lowering it into the front groove on base (J).

Secure the Glass by turning the pre-assembled

plastic knobs.

L

1

5

2

10

ASSEMBLY INSTRUCTIONS (CONT’D)

6. Place the ﬁreplace grate (N) by matching the

bottom pins into the holes on the base (J).

Slot the USB cable from the heater underneath

through the cable hole on the base (J).

N

J

6

7. Remove the ﬁlm from the adhesive on the top of

the ﬁreplace grate (N) and place the ﬁre log (M)

on the center of the ﬁreplace grate (N).

Attach the USB cable from the heater into the

USB port behind the ﬁreplace grate (N).

N

2

M

7

1

3

8. Screw two L-bracket (FF) onto the ﬁreplace brick

wall (K) using four screws (EE).

Hardware Used

EE

Screw

x 4

FF

L-Bracket

x 2

K

EE

FF

8

11

ASSEMBLY INSTRUCTIONS (CONT’D)

9. Insert the ﬁreplace brick wall (K) into the mantel,

slotting it into the grooves on base (J). Secure

it by using two screws (EE) into the L-bracket

(FF).

Hardware Used

EE

Screw

x 2

1

K

EE

J

9

2

10. Place this panel on top of ﬁrebox with corner

bumpers facing inward.

10

CORNER ASSEMBLY (OPTIONAL)

1. From behind the assembly, Attach L corner

support rod (I), secure with one washer (BB) and

one long bolt (AA).

Hardware Used

AA

Long Bolt

x 1

BB

Washer

x 1

I

BB

AA

1

12

CORNER ASSEMBLY (CONT’D)

2. Insert four wooden dowels (CC) into the top

back holes of mantel, Attach corner panel (B),

secure with ﬁve washers (BB) and ﬁve long bolts

(AA).

Assembly is now complete. With the help of

another person, move the assembly to the ﬁnal

desired location. Once in ﬁnal position you may

plug the heater into the power outlet.

Hardware Used

AA

Long Bolt

x 5

BB

Washer

x 5

CC

Wooden Dowel

x 4

B

CC

BB

AA

2

NOTE: Use the pre-assembled levelers on the

base of the ﬁreplace to level the unit. Twist the

levelers counterclockwise to increase the height,

twist the clockwise to decrease the height.

CHANGE DOOR PANEL (OPTIONAL)

Note: The pre-installed glass door panel can be switched out with the included wood door panel (H).

1. Remove the silicone trim along the outer edges of the glass panel on the inside of the ﬂip down

door. Start at a corner and pull to remove the four pieces. Be careful not to damage the silicone

trim as it will be used to secure the new panel.

2. Remove the glass panel from the door frame, then insert the included wood door panel (H).

3. Using your ﬁnger press the silicone trim back into place. Move around the outer edge of the panel

until all four sides are secure.

H

21

1

4

3

2

3

1

2

3

4

13

OPERATING INSTRUCTIONS

Control Panel Remote Control

To use the remote control, ﬁrst remove

the plastic tab by gently pullling it out of

remote control.

Controls and Display

The control panel will display the heater setting when the unit power is turned ON. Whichever control icon

you press will display the current setting of the corresponding function. Press the control icon again to adjust

the setting. Following adjustment of any setting(s), the unit will resume to display the heater setting after 5

seconds.

Power Function

• When the unit is plugged-in but not in use, F or C will illuminate to indicate that it is in stand-by

mode.

• Press the POWER ICON to turn the main power to the unit ON or OFF.

• When the unit is powered ON, the control panel will display the heater setting to indicate the unit

has power.

• Functions stored in memory will resume at the last setting.

• When the unit is powered OFF, the fan will continue to blow for a 40 second cool-down cycle prior

to shutting down (a countdown will be displayed).

Flame Brightness Function

• Press the FLAME BRIGHTNESS ICON to display the current ﬂame brightness setting.

• Press the FLAME BRIGHTNESS ICON again to scroll down through the ﬂame brightness settings:

5, 4, 3, 2, 1, OF (OFF).

Flame Speed Function

• Press the FLAME SPEED ICON to display the current ﬂame speed setting.

• Press the FLAME SPEED ICON again to scroll down through the ﬂame speed settings: 5, 4, 3, 2, 1.

14

OPERATING INSTRUCTIONS (CONT’D)

Heater Function

• Press the HEATER ICON to display the current heater setting.

• Press the HEATER ICON again to scroll down through the heater settings.

Note: Long-hold the icon to quickly scroll through settings.

• Set the heater to “HI” (High) to have the heater run continually.

• Set the heater to “OF” (OFF) to use the ﬂame functions without heat.

• This heater has a thermostat sensor to control the ambient temperature in the surrounding area

of the ﬁreplace. The heater will cycle ON and OFF to maintain the selected temperature. The

thermostat setting range is 90ºF (43°C) to 65°F (18°C).

Note: This may not exactly match the room thermostat reading as their sensors are located in

different areas.

• Hold down the FLAME SPEED ICON for 10 seconds to toggle between Fahrenheit and Celsius. “F”

or “C” will be displayed on the control panel (°F/°C can only be toggled from the control panel and

will not work if using the remote control).

• See HEATER OVERRIDE section to disengage the heater.

Sleep Timer Function (Remote Control Only)

• The Sleep TIMER function will set a countdown to shut down the unit’s main power.

• Press the TIMER ICON to display the current Sleep Timer setting.

• Press the TIMER ICON again to scroll through the timer settings, which are: 30 (minutes), 1H, 2H,

3H, 4H, 5H, 6H, 7H, 8H, 9H, OF (OFF).

• When the timer reaches zero, it will turn OFF the main power and will maintain all the settings in

memory.

HEATER OVERRIDE

The power to the heater can be disengaged to prevent the heater from being accidentally or unintentionally

powered on. This feature is primarily added to help prevent children from powering on the heater when it is not

desired.

Note: The heater override can only be set from the control panel and will not work if using the remote control.

• First turn the main power OFF. Press the POWER ICON; as the heater setting display is ﬂashing, press the

POWER ICON again and long-hold 20 seconds. The E3 symbol will display to indicate that the heater is

now disengaged.

• Note: The Flame and Timer functions will operate normally. Only the heater is disengaged.

• Repeat the same process to re-engage the heater function. The E3 symbol will change back to display the

heater setting when the heater is re-engaged.

MEMORY FUNCTION

• This unit has a memory function that allows you to turn off the MAIN POWER and retains all the other

function settings (excluding the SLEEP TIMER function).

15

CARE AND MAINTENANCE

• Make sure the unit is turned OFF, unplugged and the heating elements of heater are cool whenever you are

cleaning the heater or ﬁreplace.

• Clean the metal trim using a water-dampened soft, clean cloth. DO NOT use brass polish or household

cleaners as these products will damage the metal trim.

• The motors used on the fan and the ﬂame generator assembly are pre-lubricated for extended bearing life

and require no further lubrication. However, periodic cleaning/vacuuming of the fan/heater and air intake/

output vents are recommended.

• When the heater is not in use, the power cord should be stored properly to avoid contact with hot or sharp

objects.

• Any other servicing should be performed by an authorized service representative.

• Tips for using touch-up pen (DD): For scratches, stroke in direction of scratch. For worn areas, stroke in the

direction of wood grain. Rub excess colorant promptly with a soft cloth.

• The furnishing has no user serviceable parts.

Replacing the Remote-Control Battery

When the remote control (O) stops operating or its range

seems reduced, it is time to replace the battery. Note: The

battery should be removed if the product is to be left unused

for a long time.

1. The battery compartment is located on the back end of the

remote control (O).

2. Press the small tab inward as you slide the battery door

open and remove the old battery.

3. Insert a new CR2025 lithium battery (not included),

checking that the + and - sides of the battery match the

inside of the battery compartment.

4. Re-insert the battery door.

BATTERY

O

Note: Harmful if swallowed.

Disposal of Used Battery

A battery may contain hazardous substances that could be endangering the environment and human health.

• This symbol marked on the battery and/or packaging indicates that used

battery shall not be treated as municipal waste. Instead it shall be left at

the appropriate collection point for recycling.

• By ensuring the used battery is disposed of correctly, you will help

prevent potential negative consequences for the environment and human

health. The recycling of materials will help to conserve natural resources.

• Do not dispose of battery in ﬁre. Battery may explode or leak.

For more information about collection and recycling of used battery, please

contact your local municipality, your waste disposal service or the

point-of-sale where you purchased this battery.

16

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

Error E1 displayed on

control panel.

The overheat sensor has

been engaged.

Unplug unit, wait 15-20 minutes, then the sensor will reset

itself. Plug the unit back in and turn on the heater. If the

problem persists, call customer service.

Note: The other functions will work normally excluding the

heater.

Error E2 displayed on

control panel.

The thermostat sensor

is broken or not working

correctly.

Unplug unit, wait 15-20 minutes, then the sensor will reset

itself. Plug the unit back in and turn on the heater. If the

problem persists, call customer service.

Note: The other functions will work normally excluding the

heater.

Error E3 displayed on

control panel.

Heater override function is

engaged.

See page 14 Heater Override Section for more details.

No power. The unit does not have

power.

Check that the power cord is securely plugged into a

standard 120V outlet. Then check to make sure the unit is

powered on.

No ﬂame effect but the

unit is powered on.

The ﬂame effect is

powered off.

Push the ﬂame brightness button until desired level is

achieved.

USB cable. Connect the USB cable into the USB port behind the

Fireplace Grate.

Heater and blower

do not power on but

rest of functions are

working.

Heater setting. Set the heater to "HI" (High) to have the heater run

continually.

Power cord gets warm

to the touch.

Normal operation. This is normal for a heater appliance as it requires more

current to operate. Check the connections of the appliance

cord and the outlet. Make sure the plug ﬁts tightly into the

outlet. During use, check the plug and outlet frequently to

determine if it is HOT; if so, discontinue use of the appliance

and consult with a qualiﬁed technician to check or change

the overheating outlet(s).

Remote control does

not work.

Weak or failing battery. Replace with 1 CR-2025 battery (See page 15 for more

information).

Remote control signal

is weak and only work

sometimes.

Pressing the buttons too

quickly.

Press the buttons slowly and steadily to ensure the

transmitter recognizes the request.

Using the remote control

too far away or at an off

angle.

Move closer to the insert; the remote control will only work

within a distance of 20 feet and 45 degrees to either side

from the front of the ﬁreplace insert.

Fan motor continues

to blow after the unit is

powered off.

Normal operation. This is a standard feature; the blower runs for an additional

time to cool off the heater tubes.

17

ONE-YEAR LIMITED WARRANTY

The manufacturer warrants that your new electric ﬁreplace is free from manufacturing and material

defects for a period of one year from date of purchase, subject to the following conditions and

limitations.

Install and operate this electric ﬁreplace in accordance with the installation and operating instructions

furnished with the product at all times. Any unauthorized repair, alteration, willful abuse, accident, or

misuse of the product shall nullify this warranty.

This warranty is non-transferable, and is made to the original owner, provided that the purchase was

made through an authorized supplier of the product.

The warranty is limited to the repair or replacement of part(s) found to be defective in material or

workmanship, provided that such part(s) have been subjected to normal conditions of use and service,

after said defect is conﬁrmed by the manufacturer’s inspection.

The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by

refunding the wholesale price of the defective part(s).

Any installation, labor, construction, transportation, or other related costs/expenses arising from

defective part(s), repair, replacement, or otherwise of same, will not be covered by this warranty, nor

shall the manufacturer assume responsibility for same.

The owner/user assumes all other risks, if any, including the risk of any direct, indirect or consequential

loss or damage arising out of the use, or inability to use the product, except as provided by law.

All other warranties-expressed or implied-with respect to the product, its components and accessories,

or any obligations/liabilities on the part of the manufacturer are hereby expressly excluded.

The manufacturer neither assumes, nor authorizes any third party to assume on its behalf, any other

liabilities with respect to the sale of the product.

The warranties as outlined within this document do not apply to non-accessories used in conjunction

with the installation of this product.

This warranty is void if:

1. The ﬁreplace is subjected to prolonged periods of dampness or condensation.

2. Any unauthorized alteration, willful abuse, accident, or misuse of the product.

3. You do not have the original receipt of purchase.

18

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST,

Monday - Sunday.

HHGG II JJ LL KK MM

E

M

L

F

Q

H

K

J

G

A

N

O

P

PART DESCRIPTION PART #

A Top 2267FM-28-201-TOP

E

Insert Surround Set

PF-2267FM-28-201-INSERT

SURROUND SET

F

G

H

Flip-Down Door Center

Panels

2267FM-28-201-DOOR CENTER

PANELS

Q

J Base 2267FM-28-201-BASE

K Fireplace Brick Wall YEH-KDI-28-INSERT WALL BRICK

L Fireplace Glass Front YEH-KDI-28-GLASS FRONT

M Fire Log YEH-KDI-28-FIRELOG

N Fireplace Grate YEH-KDI-28-FIRE GRATE

O Remote Control RC-HE85EL01

P Heater YEH-KDI-28-HEATER

GG Glass Clips 2267FM-28-GLASS CLIPS

HH KD Hardware Pack

PH-2267FM-28-201-HARDWARE

PACK

II

Flip-Down Door

Hardware Set

PU17-1267FM-II/JJ/LLJJ

LL

KK

Flip-Down Door

Handle

PU17-2267FM-HANDLE

MM Leveler T-1007

Printed in Vietnam

allen + roth

®

is a trademark or registered trademark

welcoming • sophisticated • inspiring

19

ARTICLE #2416658

FOYER ÉLECTRIQUE

ET MEUBLE POUR

TÉLÉVISEUR

MODÈLE #2267FM-28-201

allen + roth

®

est une marque de commerce ou une marque

JOIGNEZ VOTRE REÇU ICI

Numéro de série __________________ Date d’achat__________________

Des questions, des problèmes, des pièces manquantes? Avant de retourner l’article au détaillant,

appelez notre service à la clientèle au 1 866 439-9800, entre 8 h et 20 h (HNE), du lundi au dimanche.

20

TABLE DES MATIÈRES

Contenu de l’emballage ..................................................................................................................... 21

Quincaillerie incluse........................................................................................................................... 22

Consignes de sécurité ....................................................................................................................... 22

Préparation ........................................................................................................................................ 26

Instructions pour l’assemblage .......................................................................................................... 26

Assemblage en coin (facultatif) ......................................................................................................... 29

Remplacement des panneaux de porte (facultatif) ............................................................................ 30

Mode d’emploi ................................................................................................................................... 31

Entretien ............................................................................................................................................ 33

Dépannage ........................................................................................................................................ 34

Garantie limitée de un an .................................................................................................................. 35

Liste des pièces de rechange ............................................................................................................ 36

La page charge ...