Wacker Neuson E1250P Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur

Ce manuel convient également à

Operator’s Manual
Notice d'emploi
Hydronic Surface Heater
Réchauffeur hydronique de surface
E1250
Type E1250
Document 5200016691
Date
0419
Version 08
Langue EN-FR
5200016691
Copyright notice
© Copyright 2019 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the
machine. Any other type of reproduction is prohibited without express
written permission from Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker
Neuson Production Americas LLC represents an infringement of valid
copyrights. Violators will be prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their
respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original instructions
This Operator’s Manual presents the original instructions. The original
language of this Operator’s Manual is American English.
wc_tx004643en.fm 3
CALIFORNIA Proposition 65 Warning
CALIFORNIA Proposition 65 Warning
WARNING
The engine exhaust from this product contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.
WARNING
Diesel engine exhaust and some of its constituents are known to the State of
California to cause cancer, birth defects, and other reproductive harm.
WARNING
Cancer and Reproductive Harm -
www.P65Warnings.ca.gov.
WARNING
Batteries, battery posts, terminals and related accessories contain lead and lead
compounds, and other chemicals known to the State of California to cause cancer
and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.
CALIFORNIA Proposition 65 Warning Proposition 65 Warning
4 wc_tx004643en.fm
This page is intentionally left blank.
wc_tx003582gb_FM10.fm
5
E1250 Foreword
Foreword
THIS HEATER IS SUITABLE FOR OUTDOOR USE ONLY.
NOTICE: WHAT TO DO IF YOU SMELL GAS:
1. Do not try to light any appliances.
2. Do not touch electrical switches; do not use any phone in your building.
3. Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
4. If you cannot reach your gas supplier, call the fire department.
WARNING
FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS
PROVIDED WITH THIS HEATER CAN RESULT IN DEATH, SERIOUS BODILY
INJURY AND PROPERTY LOSS OR DAMAGE FROM HAZARDS OF FIRE,
BURN, ASPHYXIATION, CARBON MONOXIDE POISONING, AND / OR
ELECTRICAL SHOCK.
ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE
INSTRUCTIONS SHOULD USE OR SERVICE THIS HEATER.
IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN
INSTRUCTION MANUAL, LABEL, ETC. CONTACT THE MANUFACTURER.
WARNING
WORK SITE FIRE, BURN, INHALATION, AND EXPLOSION HAZARDS.
KEEP SOLID COMBUSTIBLES, SUCH AS BUILDING MATERIALS, PAPER,
OR CARDBOARD AT A SAFE DISTANCE AWAY FROM THE MACHINE AS
RECOMMENDED BY THE INSTRUCTIONS.
NEVER USE THIS MACHINE IN SPACES WHICH DO OR MAY CONTAIN
VOLATILE OR AIRBORNE COMBUSTIBLES, OR PRODUCTS SUCH AS
GASOLINE, SOLVENTS, PAINT THINNER, DUST PARTICLES, OR
UNKNOWN CHEMICALS.
WARNING
NOT FOR HOME OR RECREATIONAL VEHICLE USE.
OPERATE THE MACHINE ONLY FOR APPLICATIONS SPECIFIED IN
MACHINE DESCRIPTION AND INTENDED USE.
wc_tx003582gb_FM10.fm
6
Foreword E1250
This heater is designed and approved for use as a construction heater in
accordance with Standard ANSI Std Z21.13, UL Stds 726, CSA Std C22.2 No. 3,
CSA Std B140.0 & B140.7.
The installation must conform to the requirements of the authority having
jurisdiction or, in the absence of such requirements, to the National Fuel Gas Code,
ANSI Z223.1/NFPA 54, and/or Natural Gas and Propane Installation Code, CAN/
CSA B149.1.
The machine, when installed, must be electrically bonded to ground in accordance
with the requirements of the authority having jurisdiction or, in the absence of such
requirements, with the National Electrical Code, ANSI/NFPA 70, and/or the
Canadian Electrical Code Part I, CSA C22.1, Electrical Code.
READ AND
SAVE THESE INSTRUCTIONS—This manual contains important
instructions for the machine models below. These instructions have been written
expressly by Wacker Neuson Production Americas LLC and must be followed
during installation, operation, and maintenance of the machines.
Machine
identification
A nameplate listing the model number, item number, revision number, and serial
number is attached to this machine. The location of the nameplate is shown above.
Machine Item Number Revisions
E1250 B 5200007613 All
E1250 B 5200012353 All
E1250 S 5200012355 All
E1250 P 5200012357 All
wc_gr011938
wc_tx003582gb_FM10.fm
7
E1250 Foreword
Serial number
(S/N)
For future reference, record the serial number in the space provided below. You will
need the serial number when requesting parts or service for this machine.
Machine
documentation
From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
Keep a copy of the Operator’s Manual with the machine at all times.
For spare parts information, please see your Wacker Neuson Dealer, or visit the
Wacker Neuson website at http://www.wackerneuson.com/.
When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Expectations
for
information in
this manual
This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions
described in this manual.
Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change any
portion of this information without notice.
The illustrations, parts, and procedures in this manual refer to Wacker Neuson
factory-installed components. Your machine may vary depending on the
requirements of your specific region.
CALIFORNIA
Proposition
65 Warning
Combustion exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental
discharge of sparks or flames from the engine exhaust. Spark arresters are
qualified and rated by the United States Forest Service for this purpose. In order to
comply with local laws regarding spark arresters, consult the engine distributor or
the local Health and Safety Administrator.
Manufacturer’s
approval
This manual contains references to approved parts, attachments, and
modifications. The following definitions apply:
Approved parts or attachments are those either manufactured or provided by
Wacker Neuson.
Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neuson.
Unapproved parts, attachments, and modifications are those that do not
meet the approved criteria.
Serial Number:
wc_tx003582gb_FM10.fm
8
Foreword E1250
Unapproved parts, attachments, or modifications may have the following
consequences:
Serious injury hazards to the operator and persons in the work area
Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.
Table of Contents
Hydronic Surface Heater
wc_bo5200016690_08TOC.fm
9
CALIFORNIA Proposition 65 Warning 3
Foreword 5
1 Safety Information 13
1.1 Signal Words Used in this Manual ..................................................... 13
1.2 Machine Description and Intended Use ............................................. 14
1.3 Safety Guidelines for Operating the Machine ..................................... 15
1.4 Safety Guidelines for Lifting the Machine ........................................... 17
1.5 Safety Guidelines for Towing the Machine ......................................... 18
1.6 Safety Guidelines for Operating Combustion Burners ....................... 19
1.7 Reporting Safety Defects ................................................................... 20
1.8 Safety Guidelines for Operating Generators ...................................... 21
1.9 Service Safety .................................................................................... 23
2 Labels 26
2.1 Label Locations .................................................................................. 26
2.2 Label Meanings .................................................................................. 27
3 Lifting and Transporting 36
3.1 Preparing the Machine for Transport on a Truck or Trailer ................ 36
3.2 Transporting the Machine on a Truck or Trailer ................................. 37
3.3 Before Towing Checklist ..................................................................... 38
3.4 Lifting the Machine ............................................................................. 39
3.5 Testing the Breakaway System—Electric Brakes .............................. 40
4 Operation 42
4.1 Preparing the Machine for First Use ................................................... 42
4.2 Breaking-in the Engine ....................................................................... 42
4.3 General Sequence of Operation ......................................................... 43
4.4 External Components ......................................................................... 44
4.5 Internal Components—Burner Access Door ...................................... 45
4.6 Internal Components—Rear Access Doors ....................................... 46
4.7 Main Control Panel Components ....................................................... 47
4.8 Generator Control Panel Components ............................................... 48
4.9 Control Display Screen ....................................................................... 49
4.10 Checking the HTF Level ..................................................................... 50
Table of Contents
Hydronic Surface Heater
wc_bo5200016690_08TOC.fm
10
4.11 Recommended Fuels and Fuel Blending Guide ..................................51
4.12 Refueling the Machine .........................................................................52
4.13 Positioning the Machine ......................................................................53
4.14 Before Starting the Machine ................................................................54
4.15 Connecting Power to the Machine ......................................................55
4.16 Starting, Operating, and Stopping—Machines without Generators .....56
4.17 Starting, Operating, and Stopping—Machines with Generators ..........58
4.18 Options Menu ......................................................................................63
4.19 Changing the Outlet Mode ..................................................................66
4.20 Changing the Operating Mode ............................................................68
4.21 Changing the Strobe Light Control ......................................................70
4.22 Unwinding and Positioning the Hoses .................................................72
4.23 Hose Spacing Guidelines ....................................................................73
4.24 Operating the Machine ........................................................................74
4.25 Rewinding the Hoses ..........................................................................76
4.26 Quick-Connect Coupling Usage and Care ..........................................77
4.27 Filling the HTF (Low Level Fault Condition) ........................................78
5 Accessories 80
5.1 HX Series Heat Exchangers ................................................................80
5.2 Pump Packs ........................................................................................80
5.3 Hose Handling Systems ......................................................................81
5.4 Insulation Blankets ..............................................................................81
5.5 Accessory Expansion Capacities ........................................................82
5.6 Expansion Diagram—1 X HHS1101 + 1 X SPP (U.S. only) ................83
5.7 Expansion Diagram—1 X HHS2202 (702) + 1 X DPP + Adapter .......84
5.8 Connecting Two HX50 (HX15) Heat Exchangers ...............................85
5.9 Connecting a HX100 (HX30) Heat Exchanger ....................................86
6 Burner Setup 87
6.1 Factory settings ...................................................................................87
6.2 Setting up the Burner ..........................................................................87
6.3 Setting and Checking the Electrodes ..................................................90
6.4 Checking and Replacing the Burner Nozzle ........................................92
6.5 Setting the “Z” Distance .......................................................................94
6.6 Adjusting the Air Settings ....................................................................95
6.7 Setting the Fuel Pressure ....................................................................96
6.8 Removing the Burner ..........................................................................97
6.9 Installing the Burner ............................................................................98
Table of Contents
Hydronic Surface Heater
wc_bo5200016690_08TOC.fm
11
7 Burner Setup—Gas 99
7.1 Factory Settings—NG/LP ................................................................... 99
7.2 Setting up the Burner ....................................................................... 100
7.3 Removing the Combustion Head ..................................................... 102
7.4 Adjusting the Ionization Probe and the Electrode ............................ 103
7.5 Changing the Burner Orifice ............................................................. 104
7.6 Checking the Burner Air Damper Setting ......................................... 105
7.7 Adjusting the Head Setting ............................................................... 106
7.8 Checking the Supply Gas Pressure ................................................. 107
7.9 Changing the Burner from Natural Gas Burning to LP Burning ........ 108
8 General Maintenance 109
8.1 Preparing for Maintenance ............................................................... 109
8.2 Periodic Maintenance Schedule ....................................................... 110
8.3 Cleaning the Machine ....................................................................... 111
8.4 Inspecting the Machine .................................................................... 111
8.5 Maintaining the Trailer ...................................................................... 112
8.6 Repairing a Hose .............................................................................. 113
8.7 Cleaning the HTF Strainer ................................................................ 115
8.8 Checking and Draining the Containment System ............................. 117
8.9 Replacing the Fuel Filter Element .................................................... 118
8.10 Lubricating the Hose Reel System ................................................... 119
8.11 Cleaning the Turbulator Tubes ......................................................... 120
8.12 Storage ............................................................................................. 122
8.13 Preparing the Machine for Seasonal Operation ............................... 123
8.14 Machine Disposal and Decommissioning ......................................... 124
9 Generator Maintenance 125
10 Troubleshooting 128
10.1 Troubleshooting the Machine ........................................................... 128
10.2 Troubleshooting the Generator ........................................................ 130
MSDS: Dowfrost HD 50 134
11 Tire Safety Information 141
Table of Contents
Hydronic Surface Heater
wc_bo5200016690_08TOC.fm
12
12 Technical Data 154
12.1 Machine—E1250B ............................................................................154
12.2 Machine—E1250S ............................................................................156
12.3 Machine—E1250P ............................................................................158
12.4 Dimensions—E1250 ..........................................................................160
13 Schematics 161
13.1 Electrical Wiring Diagram ..................................................................162
13.2 Wiring Diagram Components ............................................................163
13.3 Generator ..........................................................................................164
13.4 Generator Wiring Diagram Components ...........................................165
13.5 Generator and Receptacle Wiring—E1250S, E1250P ......................166
13.6 Generator and Receptacle Wiring—E1250S, E1250P ......................167
13.7 Control Panel Wiring .........................................................................168
13.8 Control Panel Components ...............................................................169
13.9 Control Panel Wiring .........................................................................170
13.10 Control Panel Components ...............................................................171
13.11 Control Panel Wiring .........................................................................172
13.12 Control Panel Components ...............................................................173
13.13 Control Panel Fuses ..........................................................................174
13.14 Control Panel Wiring .........................................................................175
13.15 Control Panel Components ...............................................................176
wc_si000842gb_FM10.fm
13
E1250 Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
To avoid death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
wc_si000842gb_FM10.fm
14
Safety Information E1250
1.2 Machine Description and Intended Use
Machine
description
This machine is a hydronic surface heater. The Wacker Neuson Hydronic Surface
Heaters consist of a trailer-mounted enclosure that houses an optional diesel
generator, a hydronic heater, electric motors, fixed pump(s) and plumbing, a diesel
(or gas) burner, a fuel tank, and a hose handling system.
The hydronic heating system utilizes a burner that indirectly warms the Heat
Transfer Fluid (HTF). The warmed HTF is continuously circulated through a
vented, closed loop hose system. A positive displacement pump pushes the
warmed HTF through the hose system, thereby radiating and transferring the heat
to the required application area.
An insulated blanket may be laid over the hoses to increase efficiency. The low
HTF level protection device shuts down the machine if the HTF level drops below
minimum operational capacity.
Intended use
This machine is intended to be used as a surface heater in order to thaw frozen
ground, to cure concrete, or to prevent frost and freezing. In addition, when used
with other Wacker Neuson accessories, this machine can be used to heat air.
This machine has been designed and built strictly for the intended use(s) described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty.
The following are some examples of misuse:
Using the machine to heat anything other than what is stated above
Using the machine to pump anything other than the factory recommended Heat
Transfer Fluid
Using the generator (if equipped) to power anything other than the machine
itself or Wacker Neuson accessory machines, as instructed in the Operator's
Manual
Using the machine as a ladder, support, or work surface
Using the machine to carry or transport passengers or equipment
Using the machine to tow other machines
Operating the generator (if equipped) in a manner that is inconsistent with all
federal, state, and local codes and regulations
Operating the machine outside of factory specifications
Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operator’s Manual
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
Heat, noise, and exhaust from the engine or hydronic heater
Burns from the HTF or radiant heat from the hoses
Fire hazards from improper refueling techniques
Fuel and its fumes
wc_si000842gb_FM10.fm
15
E1250 Safety Information
Personal injury from improper lifting of the trailer tongue
Tripping hazards from the hoses
To protect yourself and others, make sure you thoroughly read and understand the
safety information presented in this manual before operating the machine.
1.3 Safety Guidelines for Operating the Machine
Operator
training
Before operating the machine:
Read and understand the operating instructions contained in all manuals
delivered with the machine.
Familiarize yourself with the location and proper use of all controls and safety
devices.
Contact Wacker Neuson for additional training if necessary.
When operating this machine:
Do not allow improperly trained people to operate the machine. People
operating the machine must be familiar with the potential risks and hazards
associated with it.
Operator
qualifications
Only trained personnel are permitted to start, operate, and shut down the machine.
They also must meet the following qualifications:
Have received instruction on how to properly use the machine
Are familiar with required safety devices
The machine must not be accessed or operated by:
■Children
People impaired by alcohol, drugs, or prescription drugs
Application
area
Be aware of the application area.
Keep unauthorized personnel, children, and pets away from the machine.
Remain aware of changing positions and the movement of other equipment and
personnel in the application area/job site.
Identify whether special hazards exist in the application area, such as toxic
gases or unstable ground conditions, and take appropriate action to eliminate
the special hazards before using the machine.
Do not operate the machine in areas that contain flammable objects, fuels, or
products that produce flammable vapors.
Safety
devices,
controls, and
attachments
Only operate the machine when:
All safety devices and guards are in place and in working order.
All controls operate correctly.
The machine is set up correctly according to the instructions in the Operator’s
Manual.
The machine is clean.
The machine’s labels are legible.
wc_si000842gb_FM10.fm
16
Safety Information E1250
To ensure safe operation of the machine:
Do not operate the machine if any safety devices or guards are missing or
inoperative.
Do not modify or defeat the safety devices.
Only use accessories or attachments that are approved by Wacker Neuson.
Do not start the machine unless all cleanout doors are secured in place.
Do not attempt to start the machine when excess oil has accumulated, when the
machine is full of vapor, or when the combustion chamber is very hot.
Do not tamper with the unit or controls—call your service personnel.
Should overheating occur or the gas supply fails to shut off, do not turn off or
disconnect the electrical supply to the pump. Instead, shut off the gas supply at
a location external to the machine.
Do not use this heat exchanger if any part has been under water. Immediately
call a qualified service technician to inspect the heat exchanger and to replace
any part of the control system and any gas control which has been under water.
Safe
operating
practices
When operating this machine:
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
Do not operate a machine in need of repair.
Do not consume the operating fluids used in this machine. Depending on your
machine model, these operating fluids may include water, wetting agents, fuel
(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic oil,
heat transfer fluid (propylene glycol with additives), battery acid, or grease.
Personal
protective
equipment
(PPE)
Wear the following personal protective equipment (PPE) while operating this
machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
Safety gloves
wc_si000842gb_FM10.fm
17
E1250 Safety Information
1.4 Safety Guidelines for Lifting the Machine
When lifting the machine:
Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any
other type of lifting device used is attached securely and has enough weight-
bearing capacity to lift or hold the machine safely. See the Technical Data
chapter for machine weight.
Remain aware of the location of other people when lifting the machine.
Only use the lifting points and tie-downs described in the Operator’s Manual.
Make sure the transporting vehicle has sufficient load capacity and platform size
to safely transport the machine.
To reduce the possibility of injury:
Do not stand under the machine while it is being lifted or moved.
Do not get onto the machine while it is being lifted or moved.
wc_si000842gb_FM10.fm
18
Safety Information E1250
1.5 Safety Guidelines for Towing the Machine
When towing the machine:
Do not tow the machine if the towing vehicle’s hitch or the trailer’s coupler are
damaged.
Do not tow the machine if safety chains are damaged.
Do not tow the machine if any of the trailer’s lug nuts are loose or missing.
Do not tow the machine if the trailer’s tires have less than 1/16 inch (1.5 mm) of
tread.
Do not tow the machine if trailer tires are underinflated.
Do not tow the machine unless the trailer’s brakes are functioning properly.
Do not tow the machine if trailer lighting is not functioning properly.
Do not exceed the trailer manufacturer’s speed limitations of 89 km/h (55 mph).
When towing the machine:
Only tow the machine when the trailer’s lug nuts are properly torqued.
Only tow the machine when the trailer’s tires are properly inflated.
Only tow the machine when all trailer lights are functioning correctly.
Only tow the machine when the trailer’s safety chains are connected to the
towing vehicle in a crisscross pattern.
Maintain extra distance between the towing vehicle and other vehicles.
Avoid soft shoulders, curbs, and sudden lane changes.
Abide by all licensing requirements for your area.
If you have not driven a towing vehicle with a trailer before, practice turning,
stopping, and backing up the towing vehicle with the trailer in an area away from
traffic. Only drive the towing vehicle with the trailer when you are confident in your
ability to do so.
WARNING
Risk of severe injury or death. Improper trailer condition and towing technique can
lead to an accident.
Obey the instructions below to reduce the risk of an accident.
wc_si000842gb_FM10.fm
19
E1250 Safety Information
1.6 Safety Guidelines for Operating Combustion Burners
When using the machine:
Make sure you have proper certification or licensing required by the locality,
state, or province in which the machine is being installed to connect natural gas
or LP.
Clean up any spilled fuel immediately.
Replace the fuel tank cap after refueling the machine.
Refill the fuel tank in a well-ventilated area.
Always keep the oil supply valve shut off if the burner is shut down for an
extended period of time.
When using the machine:
Do not fill or drain the fuel tank near an open flame, while smoking, or while the
machine is running.
Do not smoke when refueling the machine.
Do not smoke when connecting natural gas or LP.
Do not attempt to start the burner when excess oil has accumulated, when the
unit is full of vapors, or when the combustion chamber is very hot.
Note: Some machines may not be capable of supporting natural gas or LP. Please
see the burner manufacturer’s literature for more information.
DANGER
Carbon monoxide. Using this machine indoors CAN KILL YOU IN MINUTES.
Exhaust gas contains carbon monoxide (CO). This is a deadly poison you cannot
see or smell. If you can smell the exhaust, you are breathing CO. Even if you
cannot smell the exhaust, you could be breathing CO.
NEVER operate the machine inside an enclosed area, such as a home, tunnel,
or garage.
ONLY use the machine outside and far away from windows, doors, and vents.
These openings can pull in exhaust gas.
ALWAYS use a battery-powered or battery-backup CO alarm in nearby
structures. Even when you use the machine correctly, CO may leak into nearby
structures.
If you start to feel sick, dizzy, or weak after the machine has been running, move
to fresh air IMMEDIATELY. See a doctor. You could have carbon monoxide
poisoning.
wc_si000842gb_FM10.fm
20
Safety Information E1250
1.7 Reporting Safety Defects
If you believe your trailer has a defect which could cause a crash or could cause
injury or death, you should immediately inform the National Highway Traffic Safety
Administration (NHTSA) in addition to notifying Wacker Neuson.
If NHTSA receives similar complaints, it may open an investigation; and if it finds
that a safety defect exists in a group of trailers, it may order a recall and remedy
campaign. However, NHTSA cannot become involved in individual problems
between you, your dealer, or Wacker Neuson.
To contact NHTSA, you may either contact the Vehicle Safety Hotline toll-free at
1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to:
Administrator
NHTSA
1200 New Jersey Avenue S.E.
Washington, DC 20590
You can also obtain other information about your motor vehicle safety from
http://www.safercar.gov
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364

Wacker Neuson E1250P Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues