KitchenAid KWCU480WSS0 Guide d'installation

Marque: KitchenAid

Modèle: KWCU480WSS0

Catégorie: Hottes

Taper: Guide d'installation

Ce manuel convient également à

KWCU460WS00

Kitchen_kid ®

36" (91.4 CM) AND 48" (121.9 CM) DESIGNER

COMMERCIAL-STYLE WALL-MOUNT CANOPY

RANGE HOOD

(;_lllIl(?

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

or visit our website at www.kitchenaid.com

In Canada, for assistance, installation and service, call: 1-800-807-6777

or visit our website at www.kitchenaid.ca

HO'I'IE DE CUISINIERE STYLISEE DE TYPE

COMMERCIAL, A MONTAGE MURAL -

36" (91,4 CM) ET 48" (121,9 CM)

Au Canada, pour assistance, installation ou service composez le 1-800-807-6777

ou visitez notre site web & www.kitchenaid.ca

Para obtener acceso al manual de uso y cuidado en espafiol, o para obtener informaci6n adicional acerca de su producto, visite:

www.kitchenaid.com.

Tenga listo su n0mero de modelo completo. Puede encontrar el n0mero de modelo y de serie dentro de la cavidad superior de la puerta.

Table of Contents/Table des matieres ............................................................................. 2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISATION Rf=SIDENTIELLE UNIQUEMENT.

W10233970D

TABLEOF CONTENTS TABLE DES MATIERES

RANGE HOOD SAFETY ................................................................. 2

INSTALLATION REQUIREMENTS ................................................ 3

Tools and Parts ............................................................................ 3

Location Requirements ................................................................ 4

Venting Requirements .................................................................. 5

Electrical Requirements ............................................................... 6

INSTALLATION INSTRUCTIONS .................................................. 6

Prepare Location .......................................................................... 6

Install Range Hood ....................................................................... 8

Make Electrical Connection ......................................................... 8

Install Chimney Covers ................................................................ 9

Install Grease Filters ..................................................................... 9

Check Operation .......................................................................... 9

RANGE HOOD USE ...................................................................... 10

Range Hood Controls ................................................................ 10

RANGE HOOD CARE ................................................................... 11

Range Hood Lamps ................................................................... 11

Cleaning ...................................................................................... 11

WIRING DIAGRAM ....................................................................... 12

ASSISTANCE OR SERVICE ......................................................... 13

In the U.S.A................................................................................ 13

In Canada ................................................................................... 13

Accessories ................................................................................ 13

WAR RANTY .................................................................................. 14

SECURITE DE LA HOTTE DE CUlSINIERE ............................... 15

EXIGENCES D'INSTALLATION ................................................... 17

Outillage et pieces ...................................................................... 17

Exigences d'emplacement ......................................................... 17

Exigences concernant I'evacuation ........................................... 18

Specifications electriques .......................................................... 19

INSTRUCTIONS D'INSTALLATION ............................................. 20

Preparation de I'emplacement ................................................... 20

Installation de la hotte ................................................................ 21

Raccordement electrique ........................................................... 22

Installation du cache-cheminee ................................................. 22

Installation des filtres a graisse .................................................. 23

ContrGle du fonctionnement ...................................................... 23

UTILISATION DE LA HOTTE DE CUlSINIERE ........................... 23

Commandes de lahotte de cuisiniere ....................................... 23

ENTRETIEN DE LA HOTTE DE CUlSINIF:RE ............................. 24

Lampes de lahotte de cuisiniere ............................................... 24

Nettoyage ................................................................................... 25

SCHEMA DE C.&,BLAGE............................................................... 26

ASSISTANCE OU SERVICE ......................................................... 27

Accessoires ................................................................................ 27

GARANTIE ..................................................................................... 28

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

m Use this unit only in the manner intended by the

manufacturer. Ifyou have questions, contact the

manufacturer.

m Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

m Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

m Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

m When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

m Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

m Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

m Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flamb6).

m Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

m Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING: a

m SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. Ifthe flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

m NEVER PICK UP A FLAMING PAN - you may be burned.

m DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

m Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you

already know how to operate it.

- The fire is small and contained in the area where it

started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

aBased on "Kitchen Fire Safety Tips" published by NFPA.

= WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

READ AND SAVE THESE iNSTRUCTiONS

INSTALLATION REQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Level

• Drill

• Drill 1W' (3 cm) drill bit

• 3/32"(2.4 mm) drill bit if installing into wood

• 5Ae"(7.9 mm) drill bit if installing optional backsplash kit

• Pencil

• Wire stripper or utility knife

• Tape measure or ruler

• Pliers

• Caulking gun and weatherproof caulking compound

• Vent clamps

• Jigsaw or keyhole saw

• Flat-blade screwdriver

• Metal snips

• Phillips screwdriver

• Scissors

Partsneeded

• Homepowersupplycable

• 1-1/2"(12.7mm)ULlistedorCSAapprovedstrainrelief

• 2ULlistedwireconnectors

• 1wallorroofcap

• Metalventsystem

• 2-250-wattmaxheatlampbulbs

Product Dimensions

Vented Installations

147/8'' (37.8 cm) "/'_ _'_-

247/8-

Parts supplied

Remove parts from packages. Check that all parts are included.

• 3 metal grease filters for 36" (91.4 cm) models

4 metal grease filters for 48" (121.9 cm) models

• 10 - #10 Phillips head mounting screws for 36" (91.4 cm)

models

12 - #10 Phillips head mounting screws for 48" (121.9 cm)

models

• 4 - washer head screws

• 4- flat head screws

• 4-"L" brackets

• Lower chimney cover

• Upper chimney cover

• Damper (2 for 48" [121.9 cm] model)

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial rating

plate is located inside the range hood on the rear wall of the

range hood.

Canopy range hood location should be away from strong draft

areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

The canopy range hood is factory set for venting through the roof

or through the wall.

All openings in ceiling and wall where canopy range hood will be

installed must be sealed.

37"

211/4" (94,0 cm)

(54.0 cm) max,

77/8'' (20.0 cm)

25" (63,5 cm)

Installation Dimensions

36" (91.4 crn) or 48" (121.9 crn)

or cabinet opening width

(if installed between cabinets)

¢- -I

)

(

)

See Note*

18" (45.7 crn) rnin.

clearance upper

cabinet to countertop

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local

codes.

36" (91.4 crn)

countertop height

*NOTE: The range hood chimneys are adjustable and designed

to meet varying ceiling or soffit heights depending on the

distance "X" between the bottom of the range hood and the

cooking surface. For higher ceilings, a 39" (99.1 cm) Chimney

Extension Kit Part Number W10197714 (Stainless Steel), is

available from your dealer or an authorized parts distributor. The

chimney extension replaces the upper chimney shipped with the

range hood.

IMPORTANT:

Minimum distance "X": 30" (76.2 cm)

Suggested maximum distance "X": 36" (91.4 cm)

For vented installations, the chimneys can be adjusted for

ceilings between 8' 4W' (2.55 m) and 9' 3W' (2.83 m).

• Ventsystemmustterminatetotheoutdoors.

• Donotterminatetheventsysteminanatticorotherenclosed

area.

• Donotuse4"(10.2cm)laundry-typewallcaps.

• Usemetalventonly.Rigidmetalventisrecommended.

Plasticormetalfoilventisnotrecommended.

• Thelengthofventsystemandnumberofelbowsshouldbe

kepttoaminimumtoprovideefficientperformance.

For the most efficient and quiet operation:

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24" (61.0 cm) of straight

vent between the elbows if more than 1 elbow is used.

• Do not install 2 elbows together.

• Use clamps to seal all joints in the vent system.

• The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

• Use caulking to seal exterior wall or roof opening around the

cap.

• The size of the vent should be uniform.

Cold weather installations

An additional back draft damper should be installed to minimize

backward cold air flow and a thermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

Roof Venting Wall Venting

A. Roof cap A. Wall cap

B. 6" (15.2 cm) B. 6" (15.2 cm)

round vent* round vent*

*The 48" (121.9 cm) range hood uses two 6" (15.2 cm) round

vents or transitions to 10" (25.4 cm) round vent using Part

Number 4396915.

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent Piece Equivalent Length

45° elbow 2.5 ft

(0.8m)

90° elbow 5.0 ft

(1.5m)

Venting Methods

A 6" (15.2 cm) round vent system is needed for installation (not

included). The range hood exhaust opening is 6" (15.2 cm) round.

Two 6" (15.2 cm) round vent systems are needed for installation

on 48" (121.9 cm) models.

NOTE: Flexible vent is not recommended. Flexible vent creates

back pressure and air turbulence that greatly reduce

performance.

Vent system can terminate either through the roof or wall. To vent

through the wall, a 90° elbow is needed.

The maximum equivalent vent lengths are:

6" (15.2 cm) round vent - 35 ft (10.7 m)

7" (17.8 cm) round vent - 40 ft (12.2 m)

8" (20.3 cm) round vent - 50 ft (15.2 m)

9" (22.9 cm) and 10" (25.4 cm) round vents - 60 ft (18.3 m)

Example vent system

90°elbow <-- 6ft(1.8rn)_1 ....Wall cap

The following example falls within the maximum recommended

vent length.

1 - 90° elbow = 5.0 ft (1.5 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Length of system = 13.0 ft (3.9 m)

Observeallgoverningcodesandordinances.

Ensurethattheelectricalinstallationisadequateandin

conformancewithNationalElectricalCode,ANSI/NFPA70(latest

edition),orCSAStandardsC22.1-94,CanadianElectricalCode,

Part1andC22.2No.0-M91(latestedition)andalllocalcodes

andordinances.

Ifcodespermitandaseparategroundwireisused,itis

recommendedthataqualifiedelectriciandeterminethatthe

groundpathisadequate.

Acopyoftheabovecodestandardscanbeobtainedfrom:

NationalFireProtectionAssociation

OneBatterymarchPark

Quincy,MA02269

CSAInternational

8501EastPleasantValleyRoad

Cleveland,OH44131-5575

• A120Volt,60Hz.,AConly,15-amp,fusedelectricalcircuitis

required.

• Ifthehousehasaluminumwiringfollowtheprocedurebelow:

1. Connectasectionofsolidcopperwiretothepigtail

leads.

2. Connectthealuminumwiringtotheaddedsectionof

copperwireusingspecialconnectorsand/ortools

designedandULlistedforjoiningcoppertoaluminum.

Followtheelectricalconnectormanufacturer'srecommended

procedure.Aluminum/copperconnectionmustconformwith

localcodesandindustryacceptedwiringpractices.

• Wiresizesandconnectionsmustconformwiththeratingof

theapplianceasspecifiedonthemodel/serialratingplate.

Themodel/serialplateislocatedbehindthefilterontherear

walloftherangehood.

• WiresizesmustconformtotherequirementsoftheNational

ElectricalCode,ANSI/NFPA70(latestedition),orCSA

StandardsC22.1-94,CanadianElectricalCode,Part1and

C22.2No.0-M91(latestedition)andalllocalcodesand

ordinances.

INSTALLATION INSTRUCTIONS

• It is recommended that the vent system be installed before

range hood is installed.

• Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

• Check your ceiling height and the range hood height

maximum before you select your range hood.

1. Disconnect power.

2. Determine which venting method to use: roof or wall.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift range hood onto covered surface.

Optional Backsplash Installation

NOTE: The following instructions are for the backsplash without

shelves. Ifyou are installing the Backsplash with Shelves for Heat

Lamps, follow the instructions included with that product. (See

"Accessories" in the "Assistance or Service" section to order.)

The hardware package supplied with the kit includes 4 plastic

wall anchors and mounting screws.

• The height of the backsplash will determine the height of the

range hood.

NOTE: The minimum height of the range hood above the

cooktop is 30" (76.2 cm). The backsplash can be extended

from 1923/32'' (50.1 cm) to 39" (99.1 cm). As the 30" (76.2 cm)

installation height increases, the range hood's capture area

decreases.

Determine height of the range hood.

Using 2 or more people, position the backsplash on the wall

so that the top of the backsplash is at the height of the

bottom edge of the range hood. Mark the location of the four

corner holes. It is recommended that the backsplash be

attached to the wall at all four corners. However, the lower

flange can be secured between the wall and backspash,

countertop or cabinet base without using the bottom corner

screws.

• Drill 5/16"(8 mm) holes.

• Push plastic wall anchors all the way into the holes.

• Position the holes in the backsplash over the wall anchors

and attach using the screws supplied.

Range Hood Mounting Screws Installation

1. Determine and mark the centerline on the wall where the

range hood will be installed.

2. Based on the ceiling or soffit height, determine the distance

"X" (30" [76.2 cm] min., suggested 36" [91.4 cm] max.)

needed between the cooking surface and the bottom of the

range hood. To this distance, add 19" (48.3 cm) and draw a

horizontal line (A) about 24" (61.0 cm) long centered on the

vertical centerline (B) at this distance.

B\ x + 19" (48.3 crn)

;

A. Horizontal fine

B. Vertical centerline

C. Cooking surface

D. Distance "X" (30" [76.2 cm] min., suggested

36" [91.4 cm] max.) + 19" (48.3 cm)

3. Following the illustrations in Step 4, mark points on each side

of the horizontal line as measured from the vertical centerline.

4. Drill 3/32"(2.4 mm) pilot holes for installation into wood. The

screws provided for mounting this range hood must be

fastened into solid wood. Do not fasten only into sheet rock.

For 36" (91.4 cm) models - 2 mounting holes

I I

A. Horizontal fine

B. Vertical centerline of range hood

C. 4_" (11.6 cm)

For 48" (121.9 cm) model) - 4 mounting holes

i D .... D i

A. Horizontal fine

B. Vertical centerline of range hood

C. 1_" (3.3 cm)

D. 9 _" (23.2 cm)

5. Install the #10 Phillips head mounting screws. Leave a

1/4"(6.4 mm) gap between the wall and the back of the screw

head to slide range hood into place.

(6.4rnrn) _

Chimney Support Bracket Installation

Place two of the chimney brackets against the wall so that

their top edges are 1Ae"(2.0 mm) from the ceiling or soffit and

level. Mark holes.

C B

A .........................I

A. Vertical centerline

B. _" (1.6 mm)

C. 11" (27.9 cm)

Place the other two chimney brackets on the wall so that their

lower edges are 161/16'' (40.8 cm) from the ceiling or soffit and

level. Mark holes.

° l

161/1o''

(40.8 rnrn)

oil [

3. Drill pilot holes.

• If installing into wood, drill 4 - 3/32"(2.4 mm) pilot holes.

4. Attach each bracket to the wall with a #10 Phillips head

mounting screw. Tighten screws securely.

Complete Preparation

1. Determine and make all necessary cuts in the wall for the vent

system. Install the vent system before installing the range

hood. See the "Venting Requirements" section.

2. Determine the location where the power supply cable will be

run through the wall. Be sure that the location will be covered

by the chimney of the range hood.

3. Drill a 11/4"(3.2 cm) hole at this location.

4. Pull enough power supply cable through the wall to allow for

easy connection to the terminal box.

5. If roof or wall cap does not have a damper, attach damper to

exhaust openings on top of the range hood using 2 Phillips

head screws.

6. If the 48" (121.9 cm) range hood is to be connected to the

10" (25.4 cm) round vent system, install the vent transition

piece now.

Use a flat-blade screwdriver and tighten the 2 leveling screws

located close to the range hood mounting brackets.

A. Leveling screw

Using 2 or more people, lift the range hood and place the

mounting hood brackets over the mounting screws. Securely

tighten the screws.

Level the range hood. Adjust the 2 leveling screws (see

Step 1)as needed.

%,. I R:I, _¢ iI

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

Disconnect power.

Remove the filters.

NOTE: Use 2 hands to remove the filters, one to pull and turn

the knob, the other to hold the filter so that it doesn't fall.

Pull knob forward (toward the front of the range hood)

while turning the knob counterclockwise to release the

locking lever.

Slide the filter down and away from the front retaining

channel.

3. Remove terminal box cover.

4. Install a UL listed or CSA approved V2"strain relief in the hole

on top of the canopy.

Run 3 wires, black, white, green or bare through strain relief,

into terminal box. Use caulking to seal openings.

................E

A. Home power supply cable

B. Black wires

C. UL listed wire connectors

D. White wires

E. Green (or bare) ground wire from home power

supply connected to green ground screw

F. Range hood power supply cable

6. Use UL listed wire connectors and connect the 3 black wires

(B) together (2 wires from the range hood and 1 wire from the

home supply cable).

7. Use UL listed wire connectors and connect the 3 white wires

(D) together (2 wires from the range hood and 1 wire from the

home supply cable).

Fire Hazard

Electrically ground the blower.

Use copper wire.

Connect ground wire to green ground screw in

terminal box.

Falure to do so can result in death, fire, or

electrical shock.

8. Connect green (or bare) ground wire from home power supply

to the unused green ground screw (E) in the terminal box.

9. Tighten strain relief screws.

10. Install terminal box cover.

11. Check all light bulbs to make sure they are secure in their

sockets.

12. Reconnect power.

1. Install damper on top of the exhaust opening. Check that the

damper opens freely. On 48" (121.9 cm) models, install

2 dampers.

2. Connect the vent system and seal all connections with

clamps.

Install Upper Chimney Cover

1. Slightly spread the sides of the cover apart and hook them

behind the chimney mounting brackets.

2. Attach the cover to the brackets with 4 flat head screws.

3. Securely tighten screws.

A. 4 flat head screws

Install Lower Chimney Cover

1. Slightly spread the sides of the cover apart and hook them

behind the upper chimney.

2. From inside the range hood, use the 4 Phillips washer head

screws to attach the lower chimney cover to the canopy of

the range hood.

3. Securely tighten screws.

NOTE: Use 2 hands to install filter, one to pull and turn the knob,

the other to hold the filter in place so that it doesn't fall.

1. Insert back edge of filter into rear channel of the filter

opening.

2. Pull out on knob and turn counterclockwise, position front

edge into place and release knob.

3. Repeat for remaining filters.

Check operation of the range hood by turning on the power.

The range hood controls are located on the right-hand

underside of the range hood.

A. Controls

B. Filters

C. Heat lamp switch

3. Move the light switch to "1" position. The light should turn on.

4. Move fan switch to "On" position. The fan should operate.

5. Move the fan speed switch to "1" position for low speed, "2"

position for medium speed, or "3" position for high speed.

6. Move fan and light switches to "Off" position to turn fan and

light off.

7. If range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

Disconnect power supply and check that the wiring is

correct.

NOTE: To get the most efficient use from your new range hood,

read the "Range Hood Use" section.

A. 4 washer head screws

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the range

hood before cooking and allow it to operate several minutes after

the cooking is complete to clear all smoke and odors from the

kitchen.

The range hood controls are located on the right-hand underside

of the range hood.

Adjusting the fan

The fan has 3 speed controls. Move the fan speed switch to "1"

position for low speed, "2" position for medium speed, or "3"

position for high speed.

Thermal Protector

The range hood is equipped with a thermal protector to avoid

overheating conditions. If the range hood shuts off while in use,

move fan slider switch to Off to turn off the range hood. Wait

approximately 60 minutes, then move slider to On to restart the

range hood.

Operating the heat lamp

The heat lamps are designed to keep food warm prior to serving.

The cooktop surface is too far away from the heat lamp to be

used as a shelf.

For best results, install a metal shelf to hold the food closer to the

lamps. The optimum distance between the shelf and the hood is

12" (30.5 cm) to 15" (38.1 cm).

B C D

A. Controls

B. Light switch

C. Fan switch

D. Fan speed switch

Operating the light

1. Move the light switch to the "1" position to turn range hood

light to night light setting.

2. Move the light switch to the "2" position to turn range hood

light to full light setting.

3. Move the light switch to the "Off" position to turn range hood

light OFE

Operating the fan

1. Move the fan switch to the "On" position to turn the fan ON.

The fan will begin operating at the speed set on the fan speed

switch.

2. Move the fan switch to the "Off" position to turn the fan OFR

Auto On Fan

The range hood is equipped with a sensor to automatically turn

on the fan when excessive heat is detected in the control area.

When the fan switch is in the "Off" position, this sensor will turn

the fan to high speed when necessary. When the heat decreases,

the fan will turn off.

When the fan switch is in the "On" position, the heat sensor is not

active and the range hood functions normally.

12" (30.5 cm) Minimum

15" (38.1 cm) Maximum

A. Range hood

B. Metal shelf

For best performance, food should be placed directly under the

heat lamps, not between them. You may need to adjust your food

placement to match your needs.

1. Install heat lamp bulbs (not included) into heat lamp sockets.

NOTE: Heat lamp bulbs should be rated to a maximum of

250 watts each. For best performance, 250 watt, R40 type,

red heat lamp bulbs are recommended. Bulb performance

varies. Lower wattage and clear bulbs decrease the

performance.

Food Poisoning Hazard

Do not let food sit for more than one hour before or

after cooking.

Doing so can result in food poisoning or sickness.

To turn on a heat lamp, move the switch for the desired lamp

into the "1" position. To turn off the heat lamp, move the

switch to the "O" position. Repeat for the other heat lamp.

NOTE: The left switch is for the left heat lamp, and the right

switch is for the right heat lamp.

RANGE HOOD CARE

.... .....[

Replacing a Halogen Lamp

This range hood uses 12-volt, 20-watt halogen lamps.

Turn off the range hood and allow the halogen lamps to cool.

To avoid damage or decreasing the life of the new bulb, do not

touch bulb with bare fingers. Replace bulb using tissue or

wearing cotton gloves to handle bulb.

To Replace:

1. Disconnect power.

2. Remove 2 screws from the circular metal trim around the

lamp assembly.

3. Pull the trim and lamp assembly down far enough so that the

lamp can be pulled out of the socket clips.

A. Remove 2 screws.

B. Pull trim with lamp assembly down.

4. Insert the new lamp into the socket clips and push the lamp

assembly back up into the range hood.

5. Replace the screws.

6. Reconnect the power.

Replacing a Heat Lamp

This range hood uses two 250 watt maximum heat lamps.

Turn off the heat lamps and allow them to cool.

To Replace:

1. Disconnect power.

2. Remove the heat lamp bulb from its socket.

3. Replace the heat lamp bulb with the same type bulb and

tighten it in its socket.

4. Repeat steps 2 and 3 with the other heat lamp bulb if

necessary.

5. Reconnect the power.

NOTE: The range hood control is equipped with a sensor that will

automatically turn the fan on high speed when excessive heat is

detected in the control area and the fan switch is in the "Off"

position.

Before cleaning or servicing the range hood, move the fan auto-

on switch to the "0" position (sensor Off). The switch is located

behind the filters. See "Metal Filters" in this section to remove the

filters.

When cleaning or servicing is complete, move the fan auto-on

switch to the "1" position (sensor On).

A. Fan auto-on switch (shown in Off position)

Exterior surfaces:

To avoid damage to the exterior surface, do not use steel wool or

soap-filled scouring pads. Rub in direction of the grain line to

avoid scratching the surface.

Always wipe dry to avoid water marks.

• Stainless Steel Cleaner and Polish.

• Mild liquid detergent and water.

• Wipe with damp soft cloth or nonabrasive sponge, then rinse

with clean water and wipe dry.

Metal Filters:

For vented installations, use 2 hands to remove filters. Turn the

knob to the left (counterclockwise) to release filter. Repeat with

other filter.

Wash metal filters as needed in dishwasher or hot detergent

solution to clean.

Reinstall the filter by placing the back edge in the channel at rear

of range hood. Push filter into place, turn the knob to the right

(clockwise) to attach to range hood. Repeat with other filter.

WIRING DIAGRAM

,,Bu_

F............. ',-w _t _%

I L Ico _1 DR 'Drk_

-,---BR-_

L I °4 _1

___ _@ @-

GY _ BR

CO J

_ BK _,

<I:CO

R R

V V

ASSISTANCE OR SERVICE

When calling for assistance or service, please know the purchase

date and the complete model and serial number of your

appliance. This information will help us to better respond to your

request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new appliance. To locate factory

specified replacement parts in your area, call us or your nearest

designated service center.

ii] iI'-_:_ I _;;(i!!I

Call the KitchenAid Customer eXperience Center toll free:

1-800-422-1230.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Installation information.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

• Referrals to local dealers, repair parts distributors and service

companies. KitchenAid designated service technicians are

trained to fulfill the product warranty and provide after-

warranty service, anywhere in the United States.

To locate the KitchenAid designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

For further assistance

If you need further assistance, you can write to KitchenAid with

any questions or concerns at:

KitchenAid Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Call the KitchenAid Canada Customer eXperience Centre toll

free: 1-800-807-6777.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Referrals to local dealers, repair parts distributors and service

companies. KitchenAid Canada designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to KitchenAid

Canada with any questions or concerns at:

Customer eXperience Centre

KitchenAid Canada

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number inyour correspondence.

Chimney Extension Kit

Order Part Number W10197714 Stainless Steel

Backsplash Kit (for use without Heat Lamp)

Order Part Number 8284756 for 36" (91.4 cm) model

Order Part Number 8284755 for 48" (121.9 cm) model

Backsplash Kit (for use with Heat Lamp)

Order Part Number W10225949 for 36" (91.4 cm) model

Order Part Number W10225948 for 48" (121.9 cm) model

Please include a daytime phone number in your correspondence.

KITCHENAID ®VENTILATION WARRANTY

LIM ITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, KitchenAid brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "KitchenAid") will pay for

Factory Specified Parts and repair labor to correct defects in materials or workmanship. Service must be provided by a KitchenAid

designated service company. This limited warranty is valid only in the United States or Canada and applies only when the major

appliance is used in the country in which it was purchased. Outside the 50 United States and Canada, this limited warranty does not

apply. Proof of original purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use or when it is used in a manner that is

contrary to published user or operator instructions and/or installation instructions.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by KitchenAid.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to KitchenAid within 30 days from the date of purchase.

6. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be

repaired in the home and only in-home service is covered by this warranty.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized KitchenAid servicer is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with published installation instructions.

10. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty

is void if the factory applied serial number has been altered or removed from your major appliance.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. KITCHENAID SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

If outside the 50 United States and Canada, contact your authorized KitchenAid dealer to determine if another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," you may find

additional help by checking the "Assistance or Service" section or by calling KitchenAid. In the U.S.A., call 1-800-422-1230. In Canada,

call 1-800-807-6777. 9/07

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

p p

SECURITE DE LA HOTTE DE CUISINIERE

Votre securit6 et celle des autres est tres importante.

Nous donnons de nombreux messages de s6curit6 importants dans ce manuel et sur votre appareil m6nager. Assurez-vous de

toujours lire tousles messages de s6curit6 et de vous y conformer.

Voici le symbole d'alerte de s6curit&

Ce symbole d'alerte de s6curit6 vous signale les dangers potentiels de d6c6s et de blessures graves & vous

et & d'autres.

Tous les messages de s6curit6 suivront le symbole d'alerte de s6curit6 et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d6ces ou de blessure grave si vous ne

suivez pas imm6diatement les instructions.

Risque possible de d6cbs ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de s6curit6 vous diront quel est le danger potentiel et vous disent comment r6duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

llVIPORTANTES iNSTRUCTiONS DE SI CURITI

AVERTISSEMENT : POUR REDUIRE LE RISQUE

D'INCENDIE, CHOC ¢:LECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

m Utiliser cet appareil uniquement dans les applications

envisag6es par le fabricant. Pour toute question, contacter

le fabricant.

m Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre I'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour emp6cher tout r6tablissement accidentel de

I'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller le tableau de disjoncteurs, placer sur letableau

de disjoncteurs une 6tiquette d'avertissement pro6minente

interdisant le r6tablissement de I'alimentation.

m Tout travail d'installation ou c&blage 61ectrique doit 6tre

r6alis6 par une personne qualifi6e, dans le respect des

prescriptions de tousles codes et normes applicables, y

compris les codes du b&timent et de protection contre les

incendies.

m Une source d'air de d6bit suffisant est n6cessaire pour le

fonctionnement correct de tout appareil & gaz (combustion

et 6vacuation des gaz & combustion par la chemin6e), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de 1'6quipement de chauffage et

les prescriptions des normes de s6curit6 - comme celles

publi6es par la National Fire Protection Association (NFPA)

et I'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorit6s r6glementaires locales.

m Lors d'op6rations de d6coupage et de per£:age dans un mur

ou un plafond, veiller & ne pas endommager les c&blages

61ectriques ou canalisations qui peuvent s'y trouver.

m Les ventilateurs d'6vacuation doivent toujours d6charger

I'air & I'ext6rieur.

IVllSE EN GARDE : Cet appareil est con£:u uniquement

pour la ventilation g6n6rale. Ne pas I'utiliser pour I'extraction

de mati_res ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et 6vacuer ad6quatement les gaz, veiller & acheminer I'air

aspir6 par un conduit jusqu'& I'ext6rieur - ne pas d6charger

I'air aspir6 dans un espace vide du b&timent comme une

cavit6 murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR R¢:DUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

MI2TALLIQUES.

AVERTISSEIVIENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINIERE :

=1Ne jamais laisser un 616ment de surface fonctionner &

puissance de chauffage maximale sans surveillance. Un

renversement/d6bordement de mati_re graisseuse pourrait

provoquer une inflammation et la g6n6ration de fum6e.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

=1Veiller &toujours faire fonctionner le ventilateur de la hotte

Iors de la cuisson avec une puissance de chauffage 61ev6e

ou Iors de la cuisson d'un mets & flamber (& savoir cr6pes

Suzette, cerise jubil6e, steak au poivre flamb6).

=1Nettoyer fr6quemment les ventilateurs d'extraction. Veiller &

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

=1Utiliser toujours un ustensile de taille appropri6e. Utiliser

toujours un ustensile adapt6 & la taille de 1'616ment

chauffant.

AVERTISSEMENT : POUR REDUIRE LE RISQUE DE

DOMMAGES CORPORELS APRF:S LE DECLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINICRE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :a

=1Placer sur le r6cipient un couvercle bien ajust6, une t61e&

biscuits ou un plateau m6tallique POUR ETOUFFER LES

FLAMMES, puis 6teindre le brOleur. VEILLER ,&.t2VITER

LES BRULURES. Si les flammes ne s'6teignent pas

imm6diatement, ¢:VACUER LA PIECE ET APPELER LES

POMPIERS.

=1NE JAMAIS PRENDRE EN MAIN UN RC:CIPIENT

ENFLAMME - vous risquez de vous brQler.

=1NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brOlante.

=1Utiliser un extincteur SEULEMENT si :

- II s'agit d'un extincteur de classe ABC, dont on connait le

fonctionnement.

- II s'agit d'un petit feu encore limit6 &I'endroit oQ il s'est

d6clar6.

- Les pompiers ont 6t6 contact6s.

- II est possible de garder le dos orient6 vers une sortie

pendant I'op6ration de lutte contre le feu.

aRecommandations tir6es des conseils de s6curit6 en cas

d'incendie de cuisine publi6s par la NFPA.

m AVERTISSEMENT : Pour r6duire le risque d'incendie

ou de choc 61ectrique, ne pas utiliser ce ventilateur avec un

quelconque dispositif de r6glage de la vitesse &semi-

conducteurs.

LIRE ET CONSERVER CES iNSTRUCTiONS

EXIGENCES D'INSTALLATION

Rassembler les outils et pieces necessaires avant de commencer

I'installation. Lire et suivre les instructions fournies avec les outils

indiqu6s ici.

Outils n6cessaires

• Niveau

• Perceuse

• Foret de 11¼"(3 cm)

• Foret de 3/32"(2,4 mm) en cas d'installation dans du bois.

• Foret de %e" (7,9 mm)) en cas d'installation d'un ensemble de

dosseret facultatif.

• Crayon

• Pince & denuder ou couteau utilitaire

• Metre-ruban ou regle

• Pince

• Pistolet & calfeutrage et compose de calfeutrage resistant

aux intemperies

• Brides de serrage pour conduit d'evacuation

• Scie sauteuse ou scie &guichet

• Tournevis &lame plate

• Cisaille de ferblantier

• Tournevis Phillips

• Ciseaux

Pi6ces n6cessaires

• Cordon d'alimentation electrique du domicile

• 1 serre-c&ble de 1/2"(12,7 mm) (homologation UL ou CSA)

• 2 connecteurs de ills homologues UL

• Bouche de decharge murale ou par le toit

• Circuit d'evacuation metallique

• 2 ampoules de lampes chauffantes de 250 W maximum

Pi_ces fournies

Retirer les pieces des emballages. Verifier que toutes les pieces

sont presentes.

• 3 filtres &graisse metalliques, pour modele de 36" (91,4 cm)

4 filtres a graisse metalliques, pour modele de 48" (121,9 cm)

• 10 vis de montage Phillips n° 10, pour modele de 36"

(91,4 cm)

12 vis de montage Phillips n° 10, pour modele de 48"

(121,9 cm)

4 vis rondelle

4 visa t_te plate

4 brides en "L"

Section inferieure du cache-cheminee

Section superieure du cache-cheminee

Clapet (2 pour modele de 48" [121,9 cm])

IMPORTANT : Observer les dispositions de tousles codes et

reglements en vigueur.

Confier I'installation de la hotte & un technicien qualifi& C'est &

I'installateur qu'incombe la responsabilite de respecter les

distances de separation specifiees sur la plaque signaletique de

I'appareil. La plaque signaletique est situee a I'interieur de la

hotte, sur la paroi arriere.

On doit toujours installer la hotte a distance des sources de

courant d'air (fen_tres, portes et bouches de chauffage).

Respecter les dimensions indiquees pour les ouvertures

decouper dans les placards; ces dimensions tiennent compte

des valeurs minimales des degagements de separation.

La hotte est configuree a I'usine pour la decharge a travers le toit

ou un mur.

Assurer I'etancheite au niveau de chaque ouverture decoupee

dans le plafond ou lemur pour I'installation de la hotte de

CUlSlnlere.

Installation dans une r_sidence mobile

L'installation de cette hotte doit satisfaire aux exigences de la

norme Manufactured Home Construction Safety Standards, Titre

24 CFR, partie 328 (anciennement Federal Standard for Mobile

Home Construction and Safety, titre 24, HUD, partie 280); Iorsque

cette norme n'est pas applicable, I'installation doit satisfaire aux

criteres de la plus recente edition de la norme Manufactured

Home Installation 1982 (Manufactured Home Sites, Communities

and Setups) ANSI A225.1/NFPA 501A*, ou des codes et

reglements Iocaux.

Dimensions du produit

Installations avec d_charge a I'ext_rieur

247/8" (63,2

[

37"

(94,0 cm)

Dimensions & respecter Iors de I'installation

18" (45,7 cm) rnin.

d_gag.

placard superieur

et plan de travail

36" (91,4 cm), ou 48" (121,9 crn)

ou largeur de rouverture du placard

(en cas d'installation entre des placards)

36" (91,4 crn)

hauteur du plan

de travail

Voir la

remarque*

*REMARQUE : La cheminee de la hotte est reglable; on peut

I'ajuster en fonction de la hauteur disponible sous plafond ou

soffite, et selon la distance "X" entre le bas de la hotte et la

surface de cuisson. Pour des hauteurs sous plafond plus

elev6es, un ensemble d'extension de cheminee de

39" (99,1 cm), piece n° W10197714 (acier inoxydable),

est disponible chez votre marchand ou chez un distributeur de

pieces autoris& L'extension de cheminee remplace la section

superieure de cheminee fournie avec la hotte.

IMPORTANT :

Valeur minimale de la distance "X" : 30" (76,2 cm)

Valeur maximale sugger6e pour la distance "X" :

36" (91,4 cm)

Pour les installations avec decharge & I'exterieur, on peut ajuster

la cheminee pour une hauteur sous plafond de 8' 4W' (2,55 m)

9' 3W' (2,83 m).

• Le systeme d'evacuation doit decharger I'air a I'exterieur.

• Ne pas terminer le systeme d'evacuation dans un grenier ou

dans un autre espace ferme.

• Ne pas utiliser une bouche de decharge murale de

4" (10,2 cm) normalement utilisee pour un equipement de

buanderie.

• Utiliser un conduit d'evacuation metallique uniquement. Un

conduit en metal rigide est recommand& L'emploi d'un

conduit de plastique ou en aluminium n'est pas recommand&

• La Iongueur du systeme d'evacuation et le nombre de coudes

doit _tre reduit au minimum pour fournir la meilleure

performance.

Pour un fonctionnement efficace et silencieux :

• Ne pas utiliser plus de trois coudes a 90°.

• Veiller & ce qu'il y ait une section droite de conduit de

24" (61,0 cm) ou plus entre deux coudes, si on doit utiliser

plus d'un coude.

• Ne pas installer 2 coudes ensemble.

• Au niveau de chaque jointure du systeme d'evacuation,

assurer I'etanch6it6 avec les brides de serrage pour conduit.

• Le systeme d'evacuation doit comporter un clapet. Si la

bouche de decharge murale ou par le toit comporte un

clapet, ne pas utiliser le clapet fourni avec la hotte de

cuisiniere.

• Autour de la bouche de decharge a I'exterieur (par le mur ou

par le toit), assurer I'etanch6it6 avec un produit de

calfeutrage.

• La taille du conduit doit _tre uniforme.

Installations pour r_gions & climat froid

On doit installer un clapet anti-reflux additionnel _ I'arriere pour

minimiser le reflux d'air froid, et incorporer un element d'isolation

thermique pour minimiser la conduction de chaleur par

I'intermediaire du systeme d'evacuation. Le clapet anti-reflux doit

_tre place du c6te air froid par rapport & I'element d'isolation

thermique.

L'element d'isolation thermique doit _tre aussi proche que

possible de I'endroit oQ le systeme d'evacuation s'introduit dans

la partie chauffee de la maison.

Air d'appoint

Les codes de b&timent Iocaux peuvent exiger I'emploi d'un

systeme d'appoint d'air Iors de I'emploi d'un ventilateur

d'extraction dont la capacite d'aspiration est superieure & un

debit (pieds cubes par minute) specifi& Le debit specifie, en

pieds cubes par minute, est variable d'une juridiction & une autre.

Consulter un professionnel des installations de chauffage/

ventilation/climatisation au sujet des exigences specifiques

applicables dans la juridiction locale.

M_thodes d'_vacuation

Un circuit d'evacuation de conduits ronds de 6" (15,2 cm) est

necessaire pour I'installation (non fourni). La hotte comporte une

ouverture de sortie de diametre 6" (15,2 cm). Deux circuits

d'evacuation ronds de 6" (15,2 cm) sont necessaires pour une

installation sur des modeles de 48" (121,9 cm).

REMARQUE : On deconseille I'emploi d'un conduit flexible. Un

conduit flexible peut causer une retro-pression et des

turbulences de I'air, ce qui reduit considerablement la

performance.

La sortie a I'exterieur du circuit d'evacuation peut se faire

travers le toit ou & travers un mur. Pour la sortie a travers un mur,

I'utilisation d'un coude de 90 ° est necessaire.

D_charge a D_charge

travers le toit travers le mur

A. Bouche de A. Bouche de

d_charge sur toit d_charge murale

B. Conduit rond B. Conduit rond

6" (15,2 cm)* 6" (15,2 cm)*

*La hotte de 48" (121,9 cm) utilise deux conduits ronds de

6" (15,2 cm) ou des raccords de transition ronds de

10" (25,4 cm); utiliser la piece numero 4396915.

Calcul de la Iongueur effective du circuit d'_vacuation

Pour calculer la Iongueur effective du circuit d'evacuation

necessaire, additionner les Iongueurs equivalentes (pieds/metres)

de tous les composants utilises dans le systeme.

Composant Longueur _quivalente

Coude & 45 ° 2,5 pi

(0,8 m)

Coude & 90 ° 5 pi

(1,5 m)

Les Iongueurs equivalentes maximales sont :

Conduit rond de 6" (15,2 cm) - 35 pi (10,7 m)

Conduit rond de 7" (17,8 cm) - 40 pi (12,2 m)

Conduit rond de 8" (20,3 cm) - 50 pi (15,2 m)

Conduits ronds de 9" (22,9 cm) et de 10" (25,4 cm) -

60 pi (18,3 m)

Exemple de syst_me de d_charge

Bouche de

Co.de0oo 0 I

L'exemple suivant indique la Iongueur de conduit recommandee

maximum.

1 coude it 90 ° = 5 pi (1,5 m)

1 bouche de decharge = 0 pi (0 m)

murale

Section droite de 8 pi = 8 pi (2,4 m)

(2,4 m)

Longueur du systeme = 13 pi (3,9 m)

Observer les dispositions de tous les codes et reglements en

vigueur.

L'installation electrique doit satisfaire les exigences de la plus

recente edition de lanorme National Electrical Code, ANSl/NFPA

70, ou de la norme CSA C22.1-94, Code canadien de I'electricite,

partie 1 et C22.2 N° 0-M91 (derniere edition) et de tousles codes

et reglements en vigueur Iocaux.

Si les codes le permettent et si on utilise un conducteur distinct

de liaison a la terre, il est recommande qu'un electricien qualifie

verifie la qualite de la liaison & la terre.

Pour obtenir un exemplaire de la norme des codes ci-dessus,

contacter :

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• L'appareil doit _tre alimente par un circuit de 120 V, CA

seulement, 60 Hz, 15 A, proteg6 par fusible.

• Si le domicile est equip6 d'un c&blage en aluminium, suivre

les instructions suivantes :

1. Connecter une section de c&ble en cuivre massif aux

conducteurs en queue de cochon.

2. Connecter le c&blage en aluminium a la section ajoutee

de c&blage en cuivre en utilisant des connecteurs et/ou

des outils specialement con(_us et homologu6s UL pour

fixer le cuivre a I'aluminium.

Appliquer la procedure recommandee par le fabricant des

connecteurs. La connexion aluminium/cuivre doit _tre

conforme aux codes Iocaux et aux pratiques de c&blage

acceptees par I'industrie.

Le calibre des conducteurs et les connexions doivent _tre

compatibles avec la demande de courant de I'appareil

specifi6e sur la plaque signaletique. La plaque signaletique

de I'appareil est situ6e derriere le filtre, sur la paroi arriere de

la hotte.

Le calibre des conducteurs doit satisfaire les exigences de la

plus recente edition de la norme National Electrical Code,

ANSl/NFPA 70, ou de la norme CSA C22.1-94, Code

canadien de I'electricit6, partie 1 et C22.2 n° 0-M91 (derniere

edition) et de tousles codes et reglements en vigueur.

INSTRUCTIONS D'INSTALLATION

• II est recommande d'installer le systeme d'evacuation avant

de proceder a I'installation de la hotte.

• Avant d'executer les decoupages, verifier la disponibilite d'un

degagement suffisant dans le plafond ou lemur pour le

conduit d'evacuation.

Avant de selectionner la hotte & installer, mesurer la hauteur

libre sous plafond et la hauteur maximum disponible sous la

hotte.

1. Deconnecter la source de courant electrique.

2. Determiner la methode d'extraction & utiliser : decharge

travers le mur ou le toit.

3. Selectionner une surface plane pour I'assemblage de la

hotte. Placer le materiau de protection sur cette surface.

Risque du poids excessif

Utiiiser deux ou plus de personnes pour d_placer et

installer la hotte de la cuisini_re.

Le non=respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

4. A I'aide de deux personnes ou plus, soulever la hotte et la

poser sur la surface couverte.

Installation avec dosseret facultative

REMARQUE : Les instructions suivantes correspondent & un

dosseret sans tablette. Si I'on installe un dosseret avec des

tablettes pour les lampes chauffantes, suivre les instructions

fournies avec ce produit-I&. (Voir "Accessoires" & la section

"Assistance ou Service" pour passer une commande.)

Le materiel de montage fourni avec I'ensemble comprend

4 chevilles d'ancrage mural en plastique et 4 vis de montage.

• La hauteur de la hotte est en fonction de la hauteur du

dosseret.

REMARQUE : La hauteur minimale de la hotte au-dessus de

la table de cuisson est de 30" (76,2 cm). Le dosseret peut

_tre rallonge de 1923/32"(50,1 cm) & 39" (99,1 cm). Au fur et &

mesure que la hauteur de I'installation de 30" (76,2 cm)

augmente, la zone de fixation de lahotte diminue.

Determiner la hauteur de la hotte.

A I'aide d'au moins 2 personnes, placer le dosseret sur lemur

de fagon &ce que le sommet du dosseret se trouve &hauteur

de la rive inferieure de la hotte. Marquer I'emplacement des

4 trous d'angle. II est recommande que le dosseret soit fixe

au mur au niveau des 4 angles. Cependant, le rebord inferieur

peut _tre fixe entre lemur et le dosseret, le plan de travail ou

la base du placard sans avoir & utiliser les vis de coin

inferieur.

Installation des vis de montage de la hotte

Determiner I'emplacement de I'axe central oQ la hotte sera

installee et tracer une ligne & cet endroit sur le mur.

En fonction de la hauteur sous plafond ou soffite, determiner

la distance "X" (30" [76,2 cm] min et 36" [91,4 cm] max.

sugger6e) necessaire entre la surface de cuisson et le bas de

la hotte. A cette distance, ajouter 19" (48,3 cm) et tracer une

ligne horizontale (A) d'environ 24" (61 cm) de Iongueur

centree par rapport & I'axe central vertical (B) a cette

distance.

B\ x + 19"(48,"_3ore)

A. Ligne horizontale

B. Axe central vertical

C. Surface de cuisson

D. Distance "X" (30" [76,2 cm] min.,

36" [91,4 cm] max. sugg_r_e)

3. En suivant les illustrations de I'etape 4, marquer un point de

chaque c6te de la ligne horizontale en mesurant & partir de

I'axe central vertical.

4. Percer des avant-trous de 3/32"(2,4 mm) pour une installation

dans du bois. Les vis fournies pour le montage de cette hotte

doivent _tre fixees dans du bois massif. Ne pas fixer

uniquement dans du placo-pl&tre.

Pour modules de 36" (91,4 cm) - 2 trous de montage

I I

; .........iT

.............................///

A. Ligne horizontale

B.Axe central vertical de la hotte

C. 49/ld' (11,6 cm)

• Percer des trous de s/le"(8 mm).

• Enfoncer completement les chevilles d'ancrage en plastique

dans les trous.

• Positionner les trous dans le dosseret par-dessus les

chevilles d'ancrage mural et fixer le dosseret & I'aide des vis

fournies.

La page charge ...

KitchenAid KWCU480WSS0 Guide d'installation

Marque: KitchenAid

Modèle: KWCU480WSS0

Catégorie: Hottes

Taper: Guide d'installation

Ce manuel convient également à

KWCU460WS00

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KWCU480WSS0 Installation guide

Documents connexes

Autres documents

Jenn-Air JXW9036WP Le manuel du propriétaire