Mode d'Emploi INE-W611D Manuel utilisateur

EN

IT

FR

NL

PL

DE

SE

ES

RU

EN

IT

FR

NL

PL

DE

SE

ES

RU

FOR CAR USE ONLY/NUR FÜR AUTOMOBIL GEBRAUCH/POUR APPLICATION AUTOMOBILE UNIQUEMENT/PARA

USO EN AUTOMÓVILES/SOLO PER L’UTILIZZO IN AUTOMOBILE/ENDAST FÖR BILBRUK/ALLEEN VOOR GEBRUIK

IN DE AUTO/ТОЛЬКО ДЛЯ ИСПОЛЬЗОВАНИЯ В АВТОМОБИЛЯХ/DO UŻYCIA TYLKO W SAMOCHODZIE

6.5-INCH NAVIGATION / DVD RECEIVER

INE-W611D

INSTALLATION MANUAL

INSTALLATIONSHANDBUCH

MANUEL D‘INSTALLATION

MANUAL DE INSTALACIÓN

MANUALE DI INSTALLAZIONE

INSTALLATIONSMANUAL

MONTAGEHANDLEIDING

РУКОВОДСТВО ПО УСТАНОВКЕ

INSTRUKCJA INSTALACJI

1

-EN

ENGLISH

Contents

WARNING ...........................................2

CAUTION .............................................2

Precautions ........................................2

Accessory List ...................................... 3

Installation ............................................ 3

Caution concerning the

installation location ............................3

Mounting the GPS Antenna

inside the vehicle ...............................3

Mounting the Microphone .................4

Installation example using the

Original Mounting Bracket .................4

Connections .......................................5

If an ACC power supply is not

available .............................................8

System Example ...............................9

2

-EN

WARNING

This symbol means important instructions. Failure to

heed them can result in serious injury or death.

DO NOT DISASSEMBLE OR ALTER.

Doing so may result in an accident, re or electric shock.

KEEP SMALL OBJECTS SUCH AS SCREWS OUT OF THE

REACH OF CHILDREN.

Swallowing them may result in serious injury. If swallowed,

consult a physician immediately.

USE THE CORRECT AMPERE RATING WHEN REPLACING

FUSES.

Failure to do so may result in re or electric shock.

DO NOT BLOCK VENTS OR RADIATOR PANELS.

Doing so may cause heat to build up inside and may result in re.

USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.

Use for other than its designed application may result in fire,

electric shock or other injury.

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or

product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may

result in re, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGA-

TIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due to

electrical shorts.

DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SUR-

ROUNDING OBJECTS.

Arrange wiring and cables in compliance with the manual to

prevent obstructions when driving. Cables or wiring that obstruct

or hang up on places such as the steering wheel, gear lever,

brake pedals, etc. can be extremely hazardous.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other

equipment. Doing so will exceed the current carrying capacity of

the wire and result in re or electric shock.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.

When drilling holes in the chassis for installation, take precautions

so as not to contact, damage or obstruct pipes, fuel lines, tanks

or electrical wiring. Failure to take such precautions may result in

re.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING

SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any

other safety-related system), or tanks should NEVER be used

for installations or ground connections. Using such parts could

disable control of the vehicle and cause re etc.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER

VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR

GEARSHIFT.

Doing so may obstruct forward vision or hamper movement etc.

and results in serious accident.

DO NOT INSTALL THE MONITOR NEAR THE PASSENGER SEAT

AIR BAG.

If the unit is not installed correctly the air bag may not function

correctly and when triggered the air bag may cause the monitor to

spring upwards causing an accident and injuries.

CAUTION

This symbol means important instructions. Failure

to heed them can result in injury or material property

damage.

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.

The wiring and installation of this unit requires special technical

skill and experience. To ensure safety, always contact the dealer

where you purchased this product to have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM

SECURELY.

Be sure to use only the specied accessory parts. Use of other

than designated parts may damage this unit internally or may not

securely install the unit in place. This may cause parts to become

loose resulting in hazards or product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY

A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like the seat

rails) or sharp or pointed edges. This will prevent crimping and

damage to the wiring. If wiring passes through a hole in metal,

use a rubber grommet to prevent the wire’s insulation from being

cut by the metal edge of the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR

DUST.

Avoid installing the unit in locations with high incidence of moisture

or dust. Moisture or dust that penetrates into this unit may result in

product failure.

3

-EN

Precautions

• Be sure to disconnect the cable from the (–) battery post

before installing your unit. This will reduce any chance of

damage to the unit in case of a short-circuit.

• Be sure to connect the color coded leads according to

the diagram. Incorrect connections may cause the unit to

malfunction or damage to the vehicle’s electrical system.

• When making connections to the vehicle’s electrical

system, be aware of the factory installed components (e.g.

on-board computer). Do not tap into these leads to provide

power for this unit. When connecting the unit to the fuse

box, make sure the fuse for the intended circuit of the unit

has the appropriate amperage. When in doubt, consult

your Alpine dealer.

• Be sure to connect the speaker (–) leads to the speaker

(–) terminal. Never connect left and right channel speaker

cables to each other or to the vehicle body.

Accessory List

• INE-W611D....................................................................... 1

• Power cable.................................................................... 1

• GPS Antenna.................................................................. 1

• Antenna mounting plate................................................. 1

• Cable clamp for antenna........................................... 1set

• USB extension cable...................................................... 2

• PRE OUT cable.............................................................. 1

• Microphone..................................................................... 1

• Interface cable................................................................ 1

• Inner case............................................................................ 1

• Face plate............................................................................ 1

• Inner case release key....................................................... 2

• Flush Head Screw (M5 8mm)........................................... 6

• Screw (M5 8mm)............................................................... 8

• Rubber cap(only INE-W611D)............................................1

• Hex Bolt(only INE-W611D)..................................................1

• Owner’s Manual........................................................... 1set

Installation

To install refer to the manual in the separately

purchased installation kit for each car type.

Caution

Do not block the unit’s fan, thus preventing air circulation. If

blocked, heat will accumulate inside the unit and may cause a re.

Air ventilation hole

Rear of the Unit

Caution concerning the installation location

Angle of installation

Install at an angle between horizontal and 30°. Note that

installing at an angle outside of this range will result in a loss

of performance and possibly damage.

0 - 30°

Mounting the GPS Antenna inside the vehicle

1

Clean the mounting location.

2

Put on the GPS Antenna mounting plate.

3

Mount the GPS Antenna.

• Do not mount the GPS Antenna inside the center

console.

- Mount the GPS Antenna on a at plane of the dash

board or rear tray.

- Make sure the GPS Antenna is not covered

(obstructed) by any metallic surface or object.

• If the GPS Antenna is mounted near the unit, the

reception becomes poor, and the location of your

vehicle may not be displayed correctly.

- Mount the GPS Antenna far away enough from the

unit.

- Bundle the GPS Antenna cable away from the rear of

the unit.

• Some thermal reection type or thermal absorption type

glass may interrupt high frequency waves. If reception

is poor with the antenna installed inside the car, try to

mount the antenna outside the car.

GPS Antenna

Antenna mounting plate

This unit

4

-EN

Mounting the Microphone

For safe use, make sure of the following:

• Location is stable and rm.

• Driver’s view and operations are not obstructed.

• Microphone is located where the driver’s voice can be

easily picked up (for example, on the sun visor).

When you speak into the microphone, you should not have

to change your driving posture. This may cause a distraction,

taking your attention away from safely driving your vehicle.

Carefully consider direction and distance while mounting the

microphone. Confirm that the driver’s voice can be easily

picked up at the selected location.

Installation example using the Original

Mounting Bracket

1

Mount the original mounting sleeve to the unit

using the supplied screws.

2

Connect all other leads of the unit according to

details described in the “Connections” (page 5).

3

Mounting the unit in a car.

• Fix the cables carefully. Do not damage them by tucking

them into movable parts, such as a seat rail, or by

locating them against sharp or pointed edges.

Note on using HDMI Connection Cables

When using HDMI connection cables, secure the cables

to the HDMI Terminals with the HDMI Fixation Bracket

(KCU-610HD).

*The HDMI bracket is not included.

1

Slide the HDMI Fixation Bracket into the grooves

(A).

2

Secure it with the screw (B).

Microphone

HDMI Terminal

HDMI Fixation Bracket

Sold Separtely

(KCU-610HD)

(A) (B)

Cable clamp

(Sold separately)

5

-EN

1

2

3

5

6

7

8

9

10

11 12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

33

36

31

32

30

34

35

4

Interface cable

SPEED SENSOR

Vehicle Antenna

GPS Antenna (Included)

To the vehicle speed pulse line

To Rear camera

To Front or Side camera

To AUX output device

To amplier or equalizer

To power antenna

To the parking brake signal lead

Rear Left

Ignition key

Battery

Front Left

Speakers

Front Right

Rear Right

To remote control input lead

To input terminal of amplier when

adding an external amplier

Microphone (Included)

To steering remote control

interface box

To remote control input lead of

Rear Monitor

To remote control output lead of

Rear Monitor

To plus side of the back lamp signal

lead of the car

(Green/White)

(Blue/White)

REVERSE

(Orange/White)

P. ANT

(Blue)

PARKING BRAKE

(Yellow/Blue)

ACC

(Red)

BATT

(Yellow)

GND

(Black)

(Green)

(Green/Black)

(White)

(White/Black)

(Gray/Black)

(Gray)

RSE REMOTE OUT

(Gray)

RSE REMOTE IN

AUX REMOTE OUT

STEERING REMOTE

MIC IN

SUBW

FRONT OUT

REAR OUT

(Gray)

(Violet)

(Violet/Black)

REAR CAMERA

AUX INPUT

REMO

FRONT OR SIDE CAMERA

PRE OUT cable

Power cable

6

-EN

〇①〇

Radio Antenna Receptacle

〇②〇

Speed Sensor Lead (Green/White)

Improper connection of the speed pulse line may cause

important safety features of the vehicle to fail (such as the

brakes or air bags). Such failures may result in an accident

and loss of life. We strongly recommend that the installation

be performed by a trained, authorized Alpine dealer.

〇③〇

Rear Camera Input Connector (RCA)

〇④〇

Front or Side Camera Input Connector (RCA)

〇⑤〇

AUX Input Connector

Input lead for AUX video/audio signal.

〇⑥〇

Remote Turn-On Lead (Blue/White)

Connect this lead to the remote turn-on lead of your amplier

or signal processor.

〇⑦〇

Reverse Lead (Orange/White)

Connect to the plus side of the car’s reverse lights. These

lights illuminate when the transmission is shifted into reverse

(R).

With this lead properly wired, the video picture automatically

switches to the rear camera whenever the car is put into

reverse (R).

〇⑧〇

Power Antenna Lead (Blue)

Connect this lead to the +B terminal of your power antenna,

if applicable.

• This lead should be used only for controlling the vehicle’s

power antenna. Do not use this lead to turn on an amplier

or a signal processor, etc.

〇⑨〇

Parking Brake Lead (Yellow/Blue)

Connect this lead to the power supply side of parking brake

switch to transmit the parking brake status signals to the

unit.

〇⑩〇

Switched Power Lead (Ignition) (Red)

Connect this lead to an open terminal on the vehicle’s fuse

box or another unused power source that provides (+)

12V only when the ignition is turned on or in the accessory

position.

〇⑪〇

Fuse Holder (15A)

〇⑫〇

Battery Lead (Yellow)

Connect this lead to the positive (+) post of the vehicle’s

battery.

〇⑬〇

Ground Lead (Black)

Connect this lead to a good chassis ground on the vehicle.

Make sure the connection is made to bare metal and is

securely fastened using the sheet metal screw provided.

〇⑭〇

Left Rear (+) Speaker Output Lead (Green)

〇⑮〇

Left Rear (–) Speaker Output Lead (Green/

Black)

〇⑯〇

Left Front (+) Speaker Output Lead (White)

〇⑰〇

Left Front (–) Speaker Output Lead (White/

Black)

〇⑱〇

Right Front (–) Speaker Output Lead (Gray/

Black)

〇⑲〇

Right Front (+) Speaker Output Lead (Gray)

20

Right Rear (–) Speaker Output Lead (Violet/

Black)

21

Right Rear (+) Speaker Output Lead (Violet)

22

Remote Control Output Lead (Gray) (For Rear

Monitor)

Connect this lead to the remote control input lead. This lead

outputs the controlling signals from the remote control.

23

Remote Control Input Lead (Gray) (For Rear

Monitor)

Connect the external Alpine product to the remote control

output lead.

24

Remote Control Output Lead (Gray) (For Aux)

Connect this lead to the remote control input lead. This lead

outputs the controlling signals from the remote control.

25

Steering Remote Control Interface Connector

To steering remote control interface box.

For details about connections, consult your nearest Alpine

dealer.

26

MIC Input Connector

To microphone (Included)

• When using the included microphone, set Microphone

Select to “Add-on” For details, refer to “Setting the

Microphone Select” in the OWNER’S MANUAL.

7

-EN

27

Subwoofer RCA Connectors

RED is right and WHITE is left.

28

Front Output RCA Connectors

Can be used as Front Output RCA Connectors. RED is right

and WHITE is left.

29

Rear Output RCA Connectors

Can be used as Rear Output RCA Connectors. RED is right

and WHITE is left.

30

GPS Antenna Receptacle

Connect to GPS antenna (Included).

31

USB Connector

To USB ash drive, iPod/iPhone or Android smartphone.

32

HDMI Input Connector

33

Power Supply Connector

34

Interface / Wired Remote connector

35

PRE OUT Connector

36

DAB Connector

8

-EN

If an ACC power supply is not available

Connection Diagram of SPST Switch (sold separately)

• If your vehicle has no ACC power supply, add an SPST (single-pole, single-throw) switch (sold separately) and fuse (sold

separately).

• The diagram and the fuse amperage shown above are in the case when the unit is used individually.

• If the switched power (ignition) lead of the unit is connected directly to the positive (+) post of the vehicle’s battery, the

unit draws some current (several hundred milliamperes) even when its switch is placed in the OFF position, and the

battery may be discharged.

To prevent external noise from entering the audio system.

• Locate the unit and route the leads at least 10 cm away from the car harness.

• Keep the battery power leads as far away from other leads as possible.

• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car

chassis.

• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer

carries various noise suppressors, contact them for further information.

• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.

ACC

SPST SW (Optional)

Battery

FUSE (5A)

(Optional)

FUSE (20A)

(Optional)

(Red)

BATTERY

(Yellow)

9

-EN

System Example

Connection of an iPhone

• Do not leave an iPhone in a vehicle for a long time. Heat and humidity may damage the iPhone, and you may not be

able to play it again.

Lower USB connector

iPhone with a Lightning

connector (sold separately)

USB extension cable (Included)

(Black)

Lightning to USB Cable

KCU-471i (sold separately)

10

-EN

Connection of a Flash Drive

• Do not leave a ash drive in a vehicle for a long time. Heat and humidity may damage the ash drive.

Connection of an HDMI Device (iPhone)

• When connecting an HDMI connection cable, be sure to secure it using the HDMI Fixation Bracket(KCU-610HD).

For details on how to secure it, see “Note on using HDMI Connection Cables” (page 4).

• Set the HDMI Setup to “HDMI.” For details, refer to “HDMI Setup” in the OWNER’S MANUAL.

• The HDMI bracket is not included.

USB connector

Lower USB

connector

HDMI input connector*

iPhone with a Lightning

connector (sold separately)

Lightning Digital AV Adapter

(Apple Inc., products)

(sold separately)

Lightning to USB Cable

KCU-471i (sold separately)

USB extension cable

(Included)

HDMI connection kit KCU-610HD (sold separately)

USB extension cable (Included)

USB Flash Drive (sold separately)

(Gray)

11

-EN

Connection of an HDMI Device (Android device)

• A connection kit or adapter kit suitable for the type of terminal on the connecting device is required.

• Set the HDMI Setup to “HDMI.” For details, refer to “HDMI Setup” in the OWNER’S MANUAL.

• * When connecting an HDMI connection cable, be sure to secure it using the HDMI Fixation Bracket (KCU-610HD/

KCU-610MH). For details on how to secure it, see “Note on using HDMI Connection Cables” (page 4).

USB connector

USB extension

cable

(Included)

HDMI input connector*

HDMI connection cable

HDMI Type-D

conversion adapter

Micro USB conversion cable

HDMI connection cable

MHL conversion

adapter

HDMI connection kit KCU-610HD (sold separately)

MHL connection kit KCU-610MH (sold separately)

Android device with

HDMI connector

(sold separately)

Android device with

MHL connector

(sold separately)

12

-EN

Connection of an External Device

5

I/F connector

(Yellow)

(Red)

(White)

To Video Output terminal

External Device

(sold separately)

To Audio Output terminal

5

AUX Input Connector

22

Remote Control Output Lead (Gray)

RCA Extension Cable (sold separately)

• You can change the name of an external device. For details, refer to “Setting the Auxiliary (AUX) Name” in the

OWNER’S MANUAL.

Interface cable

AUX INPUT

13

-EN

Connection of an External Amplier

6

27

28

29

6

Remote Turn-On Lead (Blue/White)

27

Subwoofer RCA Connectors

28

Front Output RCA Connectors

29

Rear Output RCA Connectors

RCA Extension Cable (sold separately)

PRE OUT

connector

Power cable

SUBW

FRONT OUT

REAR OUT

Power Supply connector

REMOTE ON

(Blue/White)

Amplier for subwoofer

(sold separately)

Amplier 4 ch

(sold separately)

To subwoofer input terminal

To front input terminal

To rear input terminal

Subwoofer

Front speaker

Rear speaker

REMO

REMOTE ON

(Blue/White)

(Red)

(White)

(Blue/White)

PRE OUT

cable

14

-EN

Connection of a Rearview camera

7

3

7

3

CAMERA Input Connector

7

Reverse Lead (Orange/White)

• Set the Camera Select to “Rear.” For details, refer to “Setting the Camera Input” in the OWNER’S MANUAL.

Connection of a Frontview or Sideview camera

7

3

7

3

I/F connector

Interface cable

Power Supply connector

Power

cable

CAMERA

Connect to the plus side of the car’s reverse lamp.

Reverse

(Orange/White)

RCA Extension Cable

(sold separately)

Rear Camera

(sold separately)

3

CAMERA Input Connector

Interface cable

CAMERA

RCA Extension Cable

(sold separately)

Frontview camera: (sold separately) or

Sideview camera: (sold separately)

I/F connector

15

-EN

Information on Disposal of Old Electrlcal and Electronic

Equipment and Battery (applicable for countries that have adopted

spearate waste collection systems)

If you want to dispose this product, do not mix it with general household

waste. There is a separate collection system for used electronic

products in accordance with legislation that requires proper treatment,

recovery and recycling. Contact your local authority for details in

Locating a recycle facility nearest to you. Proper recycling and waste

disposal will help conserve resources whist preventing detrimental

effects on our health and the environment.

1

-DE

DEUTSCH

Inhaltsverzeichnis

WARNUNG ...................................... 2

VORSICHT ....................................... 2

VORKEHRUNGEN .......................... 2

Zubehörliste ..................................... 3

Einbau .............................................. 3

Vorsichtshinweise zum

Einbauort ........................................3

Einbau der GPS-Antenne im

Fahrzeug ........................................3

Einbau des Mikrofons ....................4

Einbaubeispiel unter Verwendung

der Original-Montagehalterung ......4

Anschlüsse .....................................5

Fahrzeuge ohne

ACC-Spannungsversorgung ..........8

Systembeispiel ...............................9

2

-DE

WARNUNG

Dieses Symbol weist auf wichtige Anweisungen

hin. Bei Nichtbeachtung besteht die Gefahr von

schweren Verletzungen oder Todesfällen.

GERÄT NICHT ÖFFNEN.

Andernfalls besteht Unfallgefahr, Feuergefahr oder die

Gefahr eines elektrischen Schlages.

KLEINE GEGENSTÄNDE WIE SCHRAUBEN VON KINDERN

FERNHALTEN.

Werden solche Gegenstände verschluckt, besteht die

Gefahr schwerwiegender Verletzungen. Suchen Sie

unverzüglich einen Arzt auf, wenn ein Kind einen solchen

Gegenstand verschluckt.

SICHERUNGEN IMMER DURCH SOLCHE MIT DER

RICHTIGEN AMPEREZAHL ERSETZEN.

Andernfalls besteht Feuergefahr oder die Gefahr eines

elektrischen Schlages.

LÜFTUNGSÖFFNUNGEN UND KÜHLKÖRPER NICHT

ABDECKEN.

Andernfalls kann es zu einem Wärmestau im Gerät

kommen, und es besteht Feuergefahr.

DAS GERÄT NUR AN EIN 12-V-BORDNETZ IN EINEM

FAHRZEUG ANSCHLIE

ẞ

EN.

Andernfalls besteht Feuergefahr, die Gefahr eines

elektrischen Schlages oder anderer Verletzungen.

AUF KORREKTE ANSCHLÜSSE ACHTEN.

Bei fehlerhaften Anschlüssen besteht Feuergefahr, und es

kann zu Schäden am Gerät kommen.

NUR IN FAHRZEUGEN MIT 12-VOLT-BORDNETZ UND MINUS

AN MASSE VERWENDEN.

(Fragen Sie im Zweifelsfall Ihren Händler.) Andernfalls

besteht Feuergefahr usw.

VOR DEM ANSCHLUSS DAS KABEL VOM MINUSPOL DER

BATTERIE ABKLEMMEN.

Andernfalls besteht die Gefahr eines elektrischen Schlages

oder Verletzungsgefahr durch einen Kurzschluss.

DAFÜR SORGEN, DASS SICH DIE KABEL NICHT IN

GEGENSTÄNDEN IN DER NÄHE VERFANGEN.

Verlegen Sie die Kabel laut Handbuch, damit sie beim

Fahren nicht hinderlich sind. Kabel, die behindern oder auf

Stellen, wie Lenkrad, Schalthebel, Bremspedal usw. herab

hängen, können sehr gefährlich sein.

ELEKTRISCHE KABEL NICHT SPLEI

ẞ

EN.

Kabel dürfen nicht abisoliert werden, um andere Geräte mit

Strom zu versorgen. Andernfalls wird die Strombelastbarkeit

des Kabels überschritten, und es besteht Feuergefahr oder

die Gefahr eines elektrischen Schlages.

BEIM BOHREN VON LÖCHERN LEITUNGEN UND KABEL

NICHT BESCHÄDIGEN.

Wenn Sie beim Einbauen Löcher in das Fahrzeugchassis

bohren, achten Sie unbedingt darauf, die Kraftstofeitungen

und andere Leitungen, den Benzintank und elektrische

Kabel nicht zu berühren, zu beschädigen oder zu blockieren.

Werden diese Vorkehrungen missachtet, so kann dies zum

Brand führen.

SCHRAUBEN UND MUTTERN DER BREMSANLAGE NICHT

ALS MASSEPUNKTE VERWENDEN.

Schrauben oder Muttern der Brems- bzw. Lenkanlage (oder

irgendein anderes sicherheitsrelevante System) oder Tanks

dürfen NIEMALS für den Einbau oder als Masseanschluss

verwendet werden. Andernfalls besteht die Gefahr, dass

Sie die Kontrolle über das Fahrzeug verlieren oder ein

Feuer ausbricht.

DAS GERÄT NICHT AN EINER STELLE EINBAUEN, AN DER

ES BEIM FAHREN HINDERLICH SEIN KÖNNTE, WEIL ES Z. B.

DAS LENKRAD ODER DEN SCHALTHEBEL BLOCKIERT.

Andernfalls ist möglicherweise keine freie Sicht nach

vorne gegeben, oder die Bewegungen des Fahrers sind so

eingeschränkt, dass Unfallgefahr besteht.

MONITOR NICHT UNMITTELBAR NEBEN DEM

BEIFAHRERAIRBAG ANBRINGEN.

Wenn das Gerät nicht korrekt eingebaut wird, funktioniert

der Airbag unter Umständen nicht ordnungsgemäß,

und bei Auslösung des Airbags kann der Monitor hoch

geschleudert werden und Verletzungen verursachen.

VORSICHT

Dieses Symbol weist auf wichtige Anweisungen

hin. Bei Nichtbeachtung besteht die Gefahr von

Verletzungen bzw. Sachschäden.

VERKABELUNG UND EINBAU VON FACHPERSONAL

AUSFÜHREN LASSEN.

Die Verkabelung und der Einbau dieses Geräts erfordern

technisches Geschick und Erfahrung. Zu Ihrer eigenen

Sicherheit sollten Sie Verkabelung und Einbau dem

Händler überlassen, bei dem Sie das Gerät erworben

haben.

NUR DAS VORGESCHRIEBENE ZUBEHÖR VERWENDEN

UND DIESES SICHER EINBAUEN.

Verwenden Sie ausschließlich das vorgeschriebene

Zubehör. Andernfalls wird das Gerät möglicherweise

beschädigt, oder es lässt sich nicht sicher einbauen. Wenn

sich Teile lösen, stellen diese eine Gefahrenquelle dar, und

es kann zu Betriebsstörungen kommen.

DIE KABEL SO VERLEGEN, DASS SIE NICHT GEKNICKT

ODER DURCH SCHARFE KANTEN GEQUETSCHT WERDEN.

Verlegen Sie die Kabel so, dass sie sich nicht in beweglichen

Teilen (bspw. Sitzschienen) verfangen oder an scharfen

Kanten oder spitzen Ecken beschädigt werden können. So

verhindern Sie eine Beschädigung der Kabel. Wenn Sie

ein Kabel durch eine Bohrung in einer Metallplatte führen,

schützen Sie die Kabelisolierung mit einer Gummitülle vor

Beschädigung durch die Metallkanten der Bohrung.

DAS GERÄT NICHT AN STELLEN EINBAUEN, AN DENEN ES

HOHER FEUCHTIGKEIT ODER STAUB AUSGESETZT IST.

Bauen Sie das Gerät so ein, dass es vor hoher Feuchtigkeit

und Staub geschützt ist. Wenn Feuchtigkeit oder Staub

in das Gerät gelangen, kann es zu Betriebsstörungen

kommen.

La page charge ...

Mode d'Emploi INE-W611D Manuel utilisateur

Ce manuel convient également à

Mode d'Emploi INE-W611D Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents