Maytag MGR5775QDB1 Manuel utilisateur

Marque: Maytag

Modèle: MGR5775QDB1

Taper: Manuel utilisateur

Ce manuel convient également à

?vlAY] AG

Gas - Precision Touch

Control 700

Form No. A/01/08

Table of

Important Safety

instructions ............................... 1-4

Surface Cooking ...................... 5-7

Surface Controls

Sealed Gas Burners

Oven Cooking ......................... 8-17

Baking

Cook & Hold

Delay Cook & Hold

Keep Warm

Broiling

Sabbath Mode

Favorite

Oven Racks

Part No. 8113P735-60

Care & Cleaning ................... 18-21

Self=CleanOven

Cleaning Procedures

Maintenance ......................... 22=23

Oven Window & Light

Removal of Gas Appliance

Troubleshooting ................... 24=25

Warranty & Service .................... 27

Guide d'utUisation

et d'entretien ............................... 28

Guia de Uso y Cuidado ............. 56

02006 Maytag Appliances Sales Co. Litho U.S.A.

technician. Do not attempt to adjust, repair, service, or

replace any part of your appliance unless it is specifically

recommended in this guide. All other servicing should be

referred to a qualified servicer. Have the installer show

you the location of the gas shut off valve and how to

shut it off in an emergency.

Always disconnect power to appliance before servicing.

portantSafety

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible conditions

and situations that may occur. Common sense, caution,

and care must be exercised when installing, maintaining,

or operating the appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words, Labels

General instructions

Read and follow all instructions before using this

appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a

result of improper usage of the appliance. Use appliance

only for its intended purpose as described in this guide.

To ensure proper and safe operation: Appliance

must be properly installed and grounded by a qualified

Tocheckif deviceisproperlyinstalled,lookunderneath

rangewithaflashlightto makesureoneoftherear

levelinglegsisproperlyengagedinthebracketslot.The

anti-tipdevicesecurestherearlevelinglegtothefloor

whenproperlyengaged.Youshouldcheckthisanytime

therangehasbeenmoved.

Donotusewaterongreasefires.Usebakingsoda,a

drychemicalorfoam-typeextinguishertosmotherfire

orflame.

Child Safety

To Prevent Fire or Smoke

Damage

Be sure all packing materials are removed from the

appliance before operating it.

Keep area around appliance clear and free from com-

bustible materials, gasoline, and other flammable vapors

and materials.

If appliance is installed near a window, proper precau-

tions should be taken to prevent curtains from blowing

over burners.

NEVER leave any items on the cooktop. The hot air from

the vent may ignite flammable items and may increase

pressure in closed containers which may cause them to

burst.

Many aerosol-type spray cans are EXPLOSIVE when

exposed to heat and may be highly flammable. Avoid

their use or storage near an appliance.

Many plastics are vulnerable to heat. Keep plastics away

from parts of the appliance that may become warm or

hot. Do not leave plastic items on the cooktop as they

may melt or soften if left too close to the vent or a

lighted surface burner.

To eliminate the hazard of reaching over hot surface

burners, cabinet storage should not be provided directly

above a unit. If storage is provided, it should be limited

to items which are used infrequently and which are

safely stored in an area subjected to heat from an

appliance. Temperatures may be unsafe for some items,

such as volatile liquids, cleaners or aerosol sprays.

in Case of Fire

Turn off appliance and ventilating hood to avoid spread-

ing the flame. Extinguish flame then turn on hood to

remove smoke and odor.

. Cooktop: Smother fire or flame in a pan with a lid or

cookie sheet.

NEVER pick up or move a flaming pan.

. Oven: Smother fire or flame by closing the oven door.

NEVER leave children alone or unsupervised near the

appliance when it is in use or is still hot.

NEVER allow children to sit or stand on any part of the

appliance as they could be injured or burned.

Children must be taught that the appliance and utensils

in it can be hot. Let hot utensils cool in a safe place, out

of reach of small children. Children should be taught

that an appliance is not a toy. Children should not be

allowed to play with controls or other parts of the

appliance.

About Your Appliance

The oven vent is located at the base of the backguard.

Avoid touching oven vent area while oven is on and for

several minutes after oven is turned off. Some parts of

theventandsurroundingareabecomehotenoughto

causeburns.Afterovenisturnedoff,donottouchthe

ovenventorsurroundingareasuntiltheyhavehad

sufficienttimetocool.

Otherpotentiallyhotsurfacesincludecooktop,areas

facingthecooktop,ovenvent,surfacenearthevent

opening,ovendoor,areaaroundtheovendoorand

ovenwindow.

Donottouchahotovenlightbulbwithadampclothas

thebulbcouldbreak.Shouldthebulbbreak,disconnect

powertotheappliancebeforeremovingbulbto avoid

electricalshock.

Donotusethecooktoporovenasastorageareaforfood

orcookingutensils.

Cooking Safety

Always place a pan on a surface burner before turning it

on. Be sure you know which knob controls which

surface burner. Make sure the correct burner is turned

on and that the burner has ignited. When cooking is

completed, turn burner off before removing pan to

prevent exposure to burner flame.

Always adjust surface burner flame so that it does not

extend beyond the bottom edge of the pan. An excessive

flame is hazardous, wastes energy and may damage the

appliance, pan or cabinets above the appliance.

NEVER leave a surface cooking operation unattended

especially when using a high heat setting or when deep

fat frying. Boilovers cause smoking and greasy spillovers

may ignite. Clean up greasy spills as soon as possible.

Do not use high heat for extended cooking operations.

NEVER heat an unopened container on the surface

burner or in the oven. Pressure build-up may cause

container to burst resulting in serious personal injury or

damage to the appliance.

Use dry, sturdy potholders. Damp potholders may cause

burns from steam. Dish towels or other substitutes

should never be used as potholders because they can

trail across hot surface burners and ignite or get caught

on appliance parts.

Always let quantities of hot fat used for deep fat frying

cool before attempting to move or handle.

Do not let cooking grease or other flammable materials

accumulate in or near the appliance, hood or vent fan.

Clean hood frequently to prevent grease from

accumulating on hood or filter. When flaming foods

under the hood turn the fan on.

NEVER wear garments made of flammable material or

loose fitting or long-sleeved apparel while cooking.

Clothing may ignite or catch utensil handles.

Always place oven racks in the desired positions while

oven is cool. Slide oven rack out to add or remove food,

using dry, sturdy potholders. Always avoid reaching into

the oven to add or remove food. If a rack must be moved

while hot, use a dry potholder. Always turn the oven off at

the end of cooking.

Use care when opening the oven door. Let hot air or steam

escape before moving or replacing food.

PREPARED FOOD WARNING: Follow food

manufacturer's instructions. If a plastic frozen food

container and/or its cover distorts, warps, or is otherwise

damaged during cooking, immediately discard the food

and its container. The food could be contaminated.

NEVER use aluminum foil to cover oven racks or oven

bottom. This could result in risk of electric shock, fire, or

damage to the appliance. Use foil only as directed in this

guide.

Utensil Safety

Use pans with flat bottoms and handles that are easily

grasped and stay cool. Avoid using unstable, warped, easily

tipped or loose-handled pans. Also avoid using pans,

especially small pans, with heavy handles as they could be

unstable and easily tip. Pans that are heavy to move when

filled with food may also be hazardous.

Be sure utensil is large enough to properly contain food

and avoid boilovers. Pan size is particularly important in

deep fat frying. Be sure pan will accommodate the volume

of food that is to be added as well as the bubble action

of fat.

To minimize burns, ignition of flammable materials and

spillage due to unintentional contact with the utensil, do

not extend handles over adjacent surface burners. Always

turn pan handles toward the side or back of the appliance,

not out into the room where they are easily hit or reached

by small children.

Never let a pan boil dry as this could damage the utensil

and the appliance.

Follow the manufacturer's directions when using oven

cooking bags.

Only certain types of glass, glass/ceramic, ceramic or

glazed utensils are suitable for cooktop or oven usage

without breaking due to the sudden change in tempera-

ture. Follow manufacturer's instructions when using

glass.

This appliance has been tested for safe performance

using conventional cookware. Do not use any devices or

accessories that are not specifically recommended in

this guide. Do not use element covers for the surface

units, stovetop grills, or add-on oven convection

systems. The use of devices or accessories that are not

expressly recommended in this manual can create

serious safety hazards, result in performance problems,

and reduce the life of the components of the appliance.

Cleaning Safety

Turn off all controls and wait for appliance parts to cool

before touching or cleaning them. Do not touch the

burner grates or surrounding areas until they have had

sufficient time to cool.

Clean appliance with caution. Use care to avoid steam

burns if a wet sponge or cloth is used to wipe spills on a

hot surface. Some cleaners can produce noxious fumes

if applied to a hot surface.

Self-Clean Oven

Clean only parts listed in this guide. Do not clean door

gasket. The door gasket is essential for a good seal.

Care should be taken not to rub, damage, or move the

gasket. Do not use oven cleaners of any kind in or

around any part of the self-clean oven.

It is normal for the cooktop of the range to become hot

during a self-clean cycle. Therefore, touching the

cooktop during a clean cycle should be avoided.

important Safety Notice

and Warning

The California Safe Drinking Water and Toxic

Enforcement Act of 1986 (Proposition 65) requires the

Governor of California to publish a list of substances

known to the State of California to cause cancer or

reproductive harm, and requires businesses to warn

customers of potential exposures to such substances.

Users of this appliance are hereby warned that the

burning of gas can result in low-level exposure to some

of the listed substances, including benzene,

formaldehyde and soot, due primarily to the incomplete

combustion of natural gas or liquid petroleum (LP) fuels.

Properly adjusted burners will minimize incomplete

combustion. Exposure to these substances can also be

minimized by properly venting the burners to the

outdoors.

Users of this appliance are hereby warned that when

the oven is engaged in the self-clean cycle, there may

be some low-level exposure to some of the listed

substances, including carbon monoxide. Exposure to

these substances can be minimized by properly venting

the oven to the outdoors by opening the windows and/

or door in the room where the appliance is located

during the self-clean cycle.

IMPORTANT NOTICE REGARDING PET BIRDS:

Never keep pet birds in the kitchen or in rooms where

the fumes from the kitchen could reach. Birds have a

very sensitive respiratory system. Fumes released during

an oven self-cleaning cycle may be harmful or fatal to

birds. Fumes released due to overheated cooking oil, fat,

margarine and overheated non-stick cookware may be

equally harmful.

Save These instructions for Future Reference

Surfece¢ookin9

LO: Use to simmer foods, keep foods

warm and melt chocolate or butter. Some

cooking may take place on the LO setting

if the pan is covered. It is possible to

reduce the heat by rotating the knob

toward OFF. Be sure flame is stable.

HI: Use to bring liquid to a boil, or reach

pressure in a pressure cooker. Always

reduce setting to a lower heat when liquids

begin to boil or foods begin to cook.

An intermediate flame size is used to

continue cooking. Food will not cook any

faster when a higher flame setting is used

than needed to maintain a gentle boil.

Water boils at the same temperature

whether boiling gently or vigorously.

Surface Controls Surface Control Knobs

Use to turn on the surface burners. An infinite choice of heat

settings is available from LO to HI. At the HI setting a detent

or notch may be felt. The knobs can be set on or between any

of the settings.

Graphics next to the knob identify which r_['-I

burner the knob controls. For example, the

Front

graphic at right shows the left front burner IU

location.

Pilotless Ignition

Pilotless ignitioneliminates the

need for a constant standing

pilot light. Each surface burner

has a spark ignitor. Use care

when cleaning around the

surface burner.

If the surface burner does

not light, check if ignitor is

broken, soiled or wet.

BURNER CAP

BURNER BASE

Setting the controls:

The size and type of cookware will affect the heat setting.

1. Place a pan on the burner grate.

The burner flame may lift off or appear separated from

the port if a pan is not placed on the grate.

2. Push in and turn the knob counterclockwise to the LITE

setting.

A clicking (spark:}sound will be heard and the burner

will light. (All five ignitors will spark when any surface

burner knob is turned to the LITE position.:}

3. After the burner lights, turn knob to desired flame size.

The ignitor will continue to spark until the knob is

turned past the LITE position.

SurfuceCooking

Operating During a

Power Failure

1. Hold a lighted match to the desired surface burner.

2. Push in and turn the control knob slowly to LITE.

3. Adjust the flame to the desired level.

Cooktop

To prevent the cooktop from discoloring or

staining:

* Clean cooktop after each use.

* Wipe acidic or sugary spills as soon as the cooktop has

cooled as these spills may discolor the

porcelain.

Unlike a range with standard gas burners,

this cooktop does not lift-up nor isit

removable. De net attempt to lift the

ceektep for any reason.

Sealed Gas Burners

The sealed burners of your range are secured to the cooktop

and are not designed to be removed. Since the burners are

sealed intothe cooktop, boilovers or spills will not seep

underneath the cooktop.

However, the burner should be cleaned after each use. The

head portion of the burner iseasily removed for cleaning.

([Seepage 20 for cleaning directions.i)

The burner heads must be correctly placed on the burner

base for proper operation of the burner.

Power Boost Burner*

There is one high speed burner on your

range, located in the right front

position. This burner offers higher

speed cooking that can be used to

quickly bring water to a boil and for

large-quantity cooking.

• rmrm Power

_-_[ _-',J Boost

"!,\_\

Simmer Burner

This burner is located in the center

position. The simmer burner offers a

lower BTU* flame for delicate sauces or

melting chocolate. ......:::::::::

BTU ratings will vary when using LPgas.

Surfece¢ookin9

Burner Grates

The grates must be properly positioned before cooking.

When installingthe grates, place the tab ends toward the

center, matching the straight bars.

Improper installationof the grates may result in chipping of

the cooktop.

Do not operate the burners without a pan on the grate.

The grate's porcelain finish may chip without a pan to

absorb the heat from the burner flame.

Use care when stirring food in a pot/pan sitting on the burner

grate. The grates have a smooth finish for ease of cleaning.

The pot/pan will slide if the handle is not held. This may result

in spilling of hot food itemsand may be a burn hazard.

Although the burner grates are durable, they will gradually

lose their shine and/or discolor, due to the high temperatures

of the gas flame.

NOteS;

* A properly adjusted burner with clean ports will light

within a few seconds, if using natural gas, the flame

will be blue with a deeper blue inner cone.

if the burner flame isyellow or is noisy, the air/gas

mixture may be incorrect.Contact a service technician

to adjust. (Adjustments are not covered by the war-

ranty._)

With LP gas, slight yellow tips on the flames are

acceptable. This is normal and adjustment is not

necessary.

* With some types of gas,you may hear a "popping"

sound when the surface burner isturned off. This isa

normal operating sound of the burner.

If the control knob is turned very quickly from HI to

LO, the flame may go out, particularly if the burner is

cold. If this occurs, turn the knob to the OFF position,

wait several seconds and relight the burner.

The flame should be adjusted so it does not extend

beyond the edge of the pan.

Control Panel

A B C D

E F G H | J

Thecontrol panel isdesigned for easeinprogramming. Thedisplaywindow on the control shows time ofday,timer and ovenfunctions.

Control panel shown includes model specific features. (:Styling may vary depending on model.:)

!!:i_C!ii!ii!ii!ii!ii!i;

iiiD!i_iii!ii!i_ii!i

!i¸!i,!11!¸¸!¸!¸!¸!¸!¸!¸!¸!¸!¸!¸!

Broil

Bake

More+/Less-

Timer

Cook & Hold

Clean

Favorite

Clock

Keep Warm

CANCEL

Use for broiling and top browning.

Use for baking and roasting.

Enters or changes time, oven

temperature. Sets HI or LO broil.

Sets Timer.

Bakes for a preset time, then holds food

warm for 1 hour.

Use to set self-clean cycle.

Use to set and save a specific Cook &

Hold procedure.

Use to set time-of-day clock.

Use to keep cooked food warm in oven.

Cancels all operations except Timer

and Clock.

Using the Touchpads

* Pressthe desired pad.

* Press More+ or Less- to enter time or temperature.

A beep will sound when any pad is touched.

A double beep will sound if a programming error occurs.

Note: Four seconds after pressing the More+ or Less-

pad, the time or temperature will automatically be entered.

If more than 30 seconds elapse between touching a

function pad and the More+ or Less- pad, the function

will be canceled and the display will return to the previous

display.

Clock

The clock can be set to display time in a 12-hour or 24-hour

format. The clock is set at the factory for the 12-hour format.

To change the clock to 24=hour format:

1. Pressand hold the CANCEL and

Favorite pads for three seconds.

2. Press the More+ or Less =pad to

select 12 or 24 hour.

3. Set the time of day following the

directions below.

To set the Clock:

1. Pressthe Clock pad.

* The colon flashes in the display.

2. Press More+ or Less- to set the time of day.

', Colon continues flashing.

3. Press the Clock pad again or wait four

seconds. The colon stops flashing.

When electrical power is supplied or after a

power interruption, the last clock time before

power was interrupted will flash.

: More+ ::

To recall the time of day when another time function is

showing, press the Clock pad.

Clock time cannot be changed when the oven has been

programmed for Delay Cook or Delay Clean or Cook & Hold.

cont.

To cancel the Clock display:

if you do not want the time of day to display:

Press and hold the CANCEL and Clock

pads for three seconds. The time of day

will disappear from the display

When the clock display is canceled, press

the Clock pad to briefly display the time

of day.

To restore the Clock display:

Press and hold the CANCEL and Clock pads for three

seconds. The time of day will reappear in the display.

Timer

The timer can be set from one minute (0:01) up to 99 hours

and 59 minutes (99:59).

The timer can be used independently of any other oven

activity. It can also be set while another oven function is

operating.

The timer does not control the oven. It only controls a beeper.

To set the Timer:

1. Press the Timer pad.

,0:00 lights in the display.

The colon will flash.

2. Press the More+ or Less= pad until the

correct time appears in the display.

The colon will continue to flash.

3. PressTimer pad again or wait four seconds.

Timer

The colon continues flashing and the time begins

counting down.

The last minute of the timer countdown will be displayed

as seconds.

4. At the end of the set time, one long beep will sound.

To cancel the Timer:

1. Press and hold the Timer pad for three seconds.

2. Press the Timer pad and set the time to 0:00.

Locking the Control

and Oven Door

The touchpad controls and oven door can be lockedfor

safety, cleaning, or to prevent unwanted use. They will not

function when locked.

if the oven is currently in use, the controls and door cannot be

locked.

The current time of day will remain in the display when the

controls are locked.

To lock:

Press and hold the CANCEL and Cook &

Hold pads for three seconds. (Pressthe

CANCEL pad first.)

, LOCKflashes in the display.

To unlock:

Press and hold the CANCEL and Cook & Hold pads for three

seconds. (Press the CANCEL pad first.)

, LOCK disappears from the display.

Fault Codes

BAKE or LOCK may flash rapidly in the display to alert you if

there is an error or a problem, if BAKE or LOCK flash in the

display, press Cancel pad. if BAKEor LOCK continue to

flash, disconnect power to the appliance. Wait a few minutes,

and then reconnect power, if the flashing still continues,

disconnect power to the appliance and call an authorized

servicer.

Baking

To set bake:

1. Press the Bake pad.

* BAKEwill flash.

000 will light in the display.

Select the oven temperature. The oven

temperature can be set from 170° to 550°. Press

or press and hold the More+ or Less- pad.

350°will light when either pad is first pressed.

j .......................................................

Less-

...............................................

Press the More+ pad to increase the temperature.

Press the Less= pad to decrease the temperature.

Press Bake pad again or wait four seconds.

BAKEwill stop flashing and light in the display.

100° or the actual oven temperature will display. The

temperature will rise in 5° increments until the preset

temperature is reached.

4. Allow the oven to preheat for 8-15 minutes.

When the set oven temperature is reached, one long

beep will sound.

To recall the set temperature during preheat, press the

Bake pad.

5. Place food in the oven.

6. Check cooking progress at minumum cooking time. Cook

longer if needed.

7. When cooking is finished, press

CANCEL pad.

8. Remove food from the oven.

Baking Notes:

. To change the oven temperature during cooking,

press Bake pad and then the More+ or Less= pad until

you reach the desired temperature.

To change the oven temperature during preheat,

press the Bake pad twice and then the More+ or Less=

pad until you reach the desired temperature.

, If you forget to turn off the oven, it will automatically turn

off at the end of 12 hours. If you wish to deactivate this

feature, see page 14.

Baking Differences Between Your Old

and New Oven

It is normal to notice some baking time differences between a

new ovenand an old one. See"Adjusting the OvenTemperature"

on page 15.

Cook & Hold

Cook & Hold allows you to bake for a preset amount of time,

followed by a one-hour Keep Warm cycle.

To set Cook & Hold:

1. Pressthe Cook & Hold pad.

BAKE and HOLD flash.

000 lights in the display.

2. Select the oven temperature. The oven

temperature can be set from 170° to 550°. Press

or press and hold the More+ or Less- pad. Less-

Pressthe More+ pad to increase the temperature.

Pressthe Less- pad to decrease the temperature.

3. Press Cook & Hold pad again ORwait four seconds.

HOLD flashes.

00:00 flashes in the display

4. Enter the amount of time you want to bake by pressing the

More+ or Less- pad. Bake time can be set from 10

minutes (00:10)to 11 hours, 59 minutes (11:59).

BAKE and HOLD light in the display.

The baking time will light in the display.

The baking time will start counting down.

When the cooking time has elapsed:

, Four beeps will sound.

, BAKEwill turn off.

, HOLD and WARM will light.

, 170°will display.

y ..............................................

Mo r@+

After one hour in HOLD WARM:

. END will display.

. The time of day will reappear in the display.

To cancel Cook & Hold at any time:

Press the CANCEL pad. Remove food

from oven.

Delay Cook & Hold

When using Delay, the oven begins to cook later in the day.

Set the amount of time that you want to delay before the oven

turns on and how long you want to cook. The oven begins to

heat at the selected time and cooks for the specified length of

time, then keeps food warm for one hour.

Delay time can be set from 10 minutes (00:10] to 11hours, 59

minutes (11:59).

To set a Delayed Cook & Hold cycle:

1. Pressthe Bake and Timer pads at the

same time.

, DELAY lights in the display.

, 00:00 appears in the display.

2. Pressthe More+ or Less= pad to set the

delay time.

3. Pressthe Cook & Hold pad.

, 000 lights in the display.

, BAKE and HOLD flash.

4. Press More+ to setthe baking temperature.

, 00:00 and HOLD flash.

BAKE stays lit.

Press More+ to set the baking time.

The Delay time, DELAY, BAKE and HOLD light in

the display.

When the Delay time has expired:

DELAY will turn off.

Baking time and temperature are displayed.

BAKE and HOLD are displayed.

To set a Delay when Cook & Hold has already

been programmed:

1. Pressthe Bake and Timer pads. (press

the Bake pad first).

DELAY and 00:00 appear in

the display.

2. Pressthe More+ or Less= pad to set the

delay time.

DELAY will stay lit to remind you that a

delayed cooking cycle has been set.

When the Delay time has expired

and the oven starts:

d....

<:Less-

The baking time and temperature are displayed.

DELAY will turn off.

BAKE and HOLD will remain lit.

To cancel:

Press the CANCEL pad.

All timed and untimed cooking functions

will be canceled.

The time of day will reappear in the display.

Notes:

Do not use delayed baking for items that require a

preheated oven, such as cakes, cookies, and breads.

Do not use delayed baking if oven is already hot.

Keep Warm

For safely keeping foods warm or for warming breads

and plates.

To set Keep Warm:

1. Pressthe Keep Warm pad.

. WARM flashes.

.000 appears in the display.

Select the Keep Warm temperature. The Keep

Warm temperature can be set from 145° to

199°. Pressor press and hold the More+ or

Less= pad.

.179 ° will lightwhen either pad isfirst pressed.

Press the More+ pad to increase the temperature.

Press the Less= pad to decrease the temperature.

WARM and the temperature will be displayed while Keep

Warm isactive.

Keep Warm Notes:

Foroptimal food quality, oven cooked foods should be kept

warm for no longer than 1 to 2 hours.

. To keep foods from drying, cover loosely with foil or a lid.

, To warm dinner rolls:

- cover rolls loosely with foil and place in oven.

- press Keep Warm and More+ pads to set 179° F.

- warm for 12-15 minutes.

To warm plates:

- place 2 stacks of up to four plates each in the oven.

- press Keep Warm and More+ pads to set 170° F.

- warm for five minutes, turn off the oven and leave plates

in the oven for 15 minutes more.

- use only oven-safe plates, check with the manufacturer.

- do not set warm dishes on a cold surface as rapid

temperature changes could cause crazing or breakage.

To cancel Keep Warm:

1. Press the CANCEL pad.

2. Remove food from the oven.

To set BroU:

1. To begin, press the Broil pad.

BROIL flashes.

SEt isdisplayed.

2. Press the More+ pad to set HI broil or press the Less-

pad to set LO broil.

HI or LO will bedisplayed.

Select HI broil (550° F)for normal broiling. Select

LO broil (450° F) for low-temperature broiling of longer

cooking foods such as poultry.

3. After four seconds, the oven will start.

, BROIL will remain lit.

4. For optimum browning, preheat for 2-3 minutes before

adding food.

5. Place food in the oven. Close oven door.

6. Turn meat once about halfway through

cooking.

7. When food is cooked, press the CANCEL

pad. Removefood and broiler pan from the

oven.

The time of day will reappear in the display.

Broil Notes:

For best results when broiling, use a pan designed for

broiling.

HI is used for most broiling. Use LO broil when broiling

longer cooking foods. The lower temperature allows

food to cook to the well done stage without excessive

browning.

To change even temperature during broiling, press

the Broil pad and then the More+ or Less= pad to

switch between LO and HI broil.

Broil times may be longer when the lower broiling

temperature isselected.

Most foods should be turned halfway through broiling

time.

Broiling Chart

Preheat oven for 2-3 minutes.

Beef Steaks, 1"thick

Hamburger Patties, 3/4" thick

Pork Bacon

Ham, precooked 1/2" slice

Chops, 1" thick

5or6

Medium

Well Done

Warm

Well Done

15-20 min.

18-24 min.

13-18 min.

6-10 min.

8-12 min.

22-26 min.

Poultry Chicken Breasts, bone-in 4 Well Done 30-45 min. (Lo Broil)

Seafood Fish filets

Fish steaks, 1" thick

Lobster tails, 3-4 oz. each

Flaky

Done

8-12 min.

10-15 min.

7-10 min.

For a browned/seared exterior and rare interior, it may be necessary to decrease cook time on side one and decrease the distance

between the meat and heat source.

Note: This chart is a suggested guide. The times may vary with the food being cooked.

Automatic Shut=Off/

Sabbath Mode

The oven will automatically turn off after 12hours if you

accidentally leave it on. This safety feature can be turned off.

To cancel the 12=hour shut=off and run the

oven continuously for 72 hours:

1. Set the oven to bake (see page 10).

2. Pressand hold the Clock pad for five seconds.

, SAb will be displayed and flash for five seconds.

SAb will then be displayed continuously until turned off

or until the 72-hour time limit is reached.

BAKEwill also be displayed if abake cycle is in use

while the oven is in Sabbath Mode.

BAKE is the only function that operates during the

Sabbath Mode. All other functions (Timer, Keep Warm,

Clean, etc.) are locked out during the Sabbath Mode.

To cancel Bake when in Sabbath Mode:

Press CANCEL.

, BAKEwill turn off inthe display. CANCEL

, No beeps will sound.

To cancel the Sabbath Mode:

1. Press the CLOCK pad for five seconds.

2. After 72 hours, the Sabbath Mode will end.

SAb will flash for 5 seconds.

The time of day will return to the display.

Sabbath Mode Notes:

Sabbath Mode can be turned on at any time with or

without the oven on.

Sabbath Mode cannot be turned on ifthe touchpads are

locked out or when the door islocked.

, If the oven is baking when Sabbath Mode is set, BAKE

will go out at the end of the baking cycle. There will be

no audible beeps.

, If the oven light isdesired while in Sabbath Mode, it

must be turned on before the Sabbath Mode is started.

When the Sabbath Mode is started, no preheat beep will

sound.

All prompts, messages and beeps are deactivated when

Sabbath Mode is active.

The automatic door lock does not operate during the

Sabbath Mode.

, Pressing CANCEL will cancel a bake cycle, however the

control will stay in the Sabbath Mode.

If power fails, the oven will power up in Sabbath Mode

with 72 hours remaining and no cycle active.

Changing Temp °F/°C

1. The factory default setting for temperature is Fahrenheit.

2. Tochange the setting, pressand holdthe CANCEL and Bake

pads at the same time for three seconds.

3. A single beep will sound and the current setting will be

displayed (°F or °C). (If no change is made, the range will

return to the existing setting after 30 seconds.)

4. To change the setting, press the More+ or Less= pad. Press

again to return to existing setting. Wait five seconds and the

setting will be complete.

Adjusting the Oven Temperature

Oven temperatures are carefully tested for accuracy at the

factory. It is normal to notice some baking or browning

differences between a new oven and an old one. As ranges

get older, the oven temperature can shift.

You may adjust the oven temperature if you think the oven is

not baking or browning correctly. To decide how much to

change the temperature, set the temperature 25° higher or

lower than your recipe recommends, then bake. The results

of the "test" should give you an idea of how much to adjust

the temperature.

To adjust the oven temperature:

1. Press Bake.

2. Enter 550° by pressing the More+ pad.

3. Press and hold the Bake pad for several

seconds or until 0° appears in the display.

/ ...................................................

If the oven temperature was previously adjusted, the

change will be displayed. Forexample, if the oven tem-

perature was reduced by 15° the display will show "-15°''.

4. Press the More+ or Less= pad to adjust the temperature.

Eachtime a pad ispressed, the temperature changes by

5°. The oven temperature can be increasedor decreased

by 5° to 35°.

5. The time of day will automatically reappear in the display.

You do not need to readjust the oven temperature if there

isa power failure or interruption.Broiling and cleaning

temperatures cannot be adjusted.

Favorite

The Favorite pad allows you to save the time and temperature

from a Cook & Hold function.

To set a Favorite cycle, Cook & Hold must be either active or

just programmed.

To set a new Favorite cycle or to save a

currently running Cook & Hold as a Favorite:

1. Program a Cook & Hold cycle as described in the Cook &

Hold section on page 10.

2. Press and hold the Favorite pad for three

seconds.

The newly set or currently running Cook & Hold cycle

will be saved.

A beep will sound to indicate that the control has

accepted the Favorite setting.

To start a cycle programmed into Favorite:

1. Pressthe Favorite pad.

, Time and temperature for the set Cook &

Hold cycle will be displayed. (if no Cook &

Hold cycle has been programmed, "nonE"

isdisplayed.:)

2. Press the Bake pad.

, The Favorite cycle will begin immediately.

, BAKEwill light in the display

, The cooking time will light in the display

When the cooking time has elapsed:

, BAKEwill turn off.

, HOLD and WARM will light.

, 170°will display.

To cancel a Favorite cycle in progress:

....... ......

Press the CANCEL pad.

The stored Favorite cycle will not

be affected.

2. Remove food from the oven.

Pilotless |gnition

Your range is equipped with pilotless ignition. With this type of

ignitionsystem, the gas automatically shuts off and the oven

will not operate during a power failure.

A lighted match wiii not light the oven burner. No attempt

should be made to operate the oven during a power

failure.

Oven Racks

Oven Vent

When the oven is in use the area near the vent may become

hot enough to cause burns. Never block the vent opening.

The oven vent is located below the backguard vent shield

on your range.

OVEN VENT

TION

Do not place

plastics near the

vent opening as

heat from the vent

could distort or

melt the plastic.

Oven Light

The oven light automatically comes on when the

door isopened. When the door isclosed, press the

Oven Light switch to turn the oven light on and off.

Oven

Oven Bottom

Protect oven bottom against spillovers, especially acidic or

sugary spills, as they may discolor the porcelain enamel. Use

the correct pan size to avoid spillovers and believers. Do not

place utensils or aluminum foil directly on the oven

bottom.

The oven has two racks. All racks are designed with a lock-

stop edge.

To remove:

1. Pull rack straight out until it

stops at the lock-stop position.

2. Lift up on the front of the rack

and pull out.

To replace:

1. Place rack on the rack supports in the oven.

2. Tilt the front end up slightly. Slide rack back until it clears

the lock-stop position.

3. Lower front and slide back intothe oven.

Do not cover an entire rack with aluminum foil or place

foil on the oven bottom. Baking results will be affected

and damage may occur to the oven bottom.

Rack Positions

RACK 7 (:highest

position:): Forsingle rack

baking on cookie sheets

and broiling.

RACK 6: Used for

single rack baking on

cookie sheets and

broiling. Usedfor

multiple rack baking.

Bottom

Two Rack Baking

RACK 5: For single rack baking on cookie sheets and broiling.

RACK 4: Used for single rack baking on cookie sheets, sheet

cakes, casseroles and broiling. Usedfor multiple rack baking.

RACK 3: For single rack baking on cookie sheets, casseroles,

layer cakes, loaves of bread and sheet cakes. Used for

multiple rack baking.

RACK 2: Used for single rack baking on cookie sheets and

roasting small cuts of meat. Used for multiple rack baking.

RACK 1: Use for roasting large cuts of meat and poultry.

cont.

Oven Bottom:Placeovenrackon

raisedsidesofovenbottom.Use

foradditionalspacewhen cooking

largeovenmeals.

MULTIPLE RACK COOKING:

Two rack: Use rack positions 3

and 6, or 2 and 4.

Baking Layer Cakes on Two Racks

For best results when baking cakes on two racks, use racks

2 and 4.

Place the cakes on the rack as shown.

Create-A-Space TMHalf Rack

Select range models are

equipped with a convertible _

half rack. The left side of

the rack can be removed _ l__

to accommodate a large

roaster on the lower _ _//

rack. The right side of

the rack isstill

available to hold a

casserole dish.

Notes:

, The removable section of the rack can be used as a

roasting rack in a broiling pan. Do not use the top insert

when using the rack in a broiling pan.

The removable section of the rack can be used as a

cooling rack or trivet.

Make sure oven is cool before removing or reinstalling

the half rack.

Do not use cookware that extends beyond edge of rack.

For best results, allow two inches between the pan

placed on the rack and the oven side wall.

Use caution when remowng items from the half rack to

avoid burns.

Carefully remove items from the lower rack to avoid

disturbing the half rack.

¢leanin

Self-Clean Oven

The self-clean cycle uses above-normal cooking temperatures

to automatically clean the oven interior.

The oven should be cleaned regularly by wiping up spillovers

to prevent excessive smoke and flare-ups. Do not allow a

heavy build-up of soil to accumulate in the oven.

During the cleaning process, the kitchen should be well

ventilated to get rid of normal odors associated with cleaning.

Before Self=Cleaning

1. Turn off the oven light before cleaning. The light may burn

out during the clean cycle.

Remove all pans and oven racks from the oven. The oven

racks will discolor and may not slide easily after a self-

clean cycle if they are not removed.

Clean oven frame, door frame, area

outside of gasket, and around the

opening in the door gasket with a

nonabrasive cleaner such as Bon

AmP or detergent and water. The

self-cleaning process does not

clean these areas. They should be

cleaned to prevent soil from baking on during the clean

cycle. (The gasket isthe seal around the oven door and

window.:)

4. To prevent damage, do not clean or rub the gasket around

the oven door. The gasket is designed to seal in heat

during the clean cycle.

5. Wipe up excess grease or spillovers from the oven bottom.

This prevents excessive smoking, flare-ups or flaming

during the clean cycle.

6. Wipe up sugary and acidic spillovers such as sweet

potatoes, tomato, or milk-based sauces. Porcelain enamel

is acid-resistant, not acid-proof. The porcelain finish may

discolor if acidic spills are not wiped up before a self-clean

cycle.

To set Self=Clean:

i ote: Oven temperature must be below 400° Fto program

a clean cycle.

Close the oven door.

Pressthe Clean pad.

* CLEAN flashes in the display.

Pressthe More+ or Less- pad.

*MEd (Medium soil, 3 hours:) is displayed.

If the door is not closed, beeps will sound and "door" will

display. If the door is not closed within 45 seconds, the

self-cleaning operation will be canceled and the display

will return to the time of day.

Pressthe More+ or Less- pad to scroll through

the self-cleaning settings.

HVy (Heavy Soil, 4 hours:) Less- i

MEd (Medium soil, 3 hours:)

LITE( Light Soil, 2 hours:)

Choosing the soil level of the oven automatically programs

the self-cleaning time.

After four seconds, the oven will start cleaning.

* The cleaning time will start counting down in the display.

* LOCK will appear in the display.

* CLEAN will appear in the display.

To Delay a Self=Clean Cycle:

1. Pressthe Clean and Timer pads.

* DELAY and 00:00 will appear in the

display.

2. Press the More+ or Less= pad to set the

amount of time you want to delay the cycle.

Delay time can be set from ten minutes

(00:10:)to 11 hours, 59 minutes (11:59:).

Pressthe Clean pad.

* CLEAN will flash.

Pressthe More+ or Less= pad.

* MEd (Medium soil, 3 hours:)is displayed.

cont.

*Brand names for cleaning products are registered trademarks ofthe respective manufacturers.

5. Press the More+ or Less- pad to scroll through the self-

cleaning settings.

HVy (HeavySoil, 4 hours)

MEd (Medium soil, 3 hours)

LITE ( Light Soil, 2 hours)

Choosing the soil level of the oven automatically programs

the self-cleaning time.

6. After four seconds, CLEAN, DELAY and LOCK will appear

in the display to show that the oven is setfor a delayed

clean operation. The delay time is displayed.

During the Self=Clean Cycle

When LOCK shows in the display, the door cannot be opened.

To prevent damage to the door, do not force the door open

when LOCK is displayed.

Smoke and Smells

You may see some smoke and smell an odor the first few

times the oven iscleaned. This isnormal and will lessen in

time.

Smoke may also occur if the oven is heavily soiled or if a pan

was left in the oven.

Sounds

As the oven heats,you may hear sounds of metal parts

expanding and contracting. This isnormal and will not

damage the oven.

if the oven has already been set for a clean

cycle and you wish to set a delay:

1. Press the Clean and Timer pads. (Press

the Clean pad first)

, DELAY flashes.

, 00:00will appear in the display.

2. Press the More+ or Less=pad to set the amount of time

you want to delay the cycle.

After four seconds, CLEAN, DELAY and LOCK will appear

in the display to show that the oven isset for a delayed

clean operation. The delay time isdisplayed.

When the Self-Clean cycle starts:

, DELAY will turn off.

The clean time will appear inthe display.

To cancel the Self-Clean cycle:

Press the CANCEL pad.

CANCEL

, All words disappear from the display.

All functions are canceled.

The time of day appears in the display.

After Self=Cleaning

About one hour after the end of the self-clean cycle, LOCK

will turn off. The door can then be opened.

Some soil may leave a light gray, powdery ash. Remove

it with a damp cloth, if soil remains after wiping, that means

the clean cycle was not long enough. The soil will be re-

moved during the next clean cycle.

If oven racks were left in the oven and do not slide

smoothly after a clean cycle, wipe racks and rack supports

with a small amount of vegetable oil to make them easier to

move.

Fine lines may appear in the porcelain because it went

through heating and cooling. This isnormal and will not

affect performance.

A white discoloration may appear after cleaning if acidic

or sugary foods were not wiped up before the self=clean

cycle. This discoloration is normal and will not affect perfor-

mance.

Notes:

If the oven door is left open, "door" will flash inthe

display and a signal will beep until the door isclosed

and the Clean pad ispressed again.

If more than five seconds elapse between pressing the

Clean pad and the More+ or Less= pads, the program

will automatically return to the previous display.

The oven door will be damaged if the oven door is

forced to open when LOCK isstill displayed.

La page charge ...

Maytag MGR5775QDB1 Manuel utilisateur

Marque: Maytag

Modèle: MGR5775QDB1

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MGR5775QDB1 User manual
español: Maytag MGR5775QDB1 Manual de usuario

Maytag MGR5775QDB1 Manuel utilisateur

Ce manuel convient également à

Maytag MGR5775QDB1 Manuel utilisateur

dans d''autres langues

Documents connexes