Phcbi MDF-MU300H Mode d'emploi

Please read the operating instructions carefully before using this product, and keep the operating

instructions for future use.

See page 32 for all model numbers.

Operating Instructions

Biomedical Freezer

MDF-MU500H

1

CONTENTS

INTRODUCTION P. 2

PRECAUTIONS FOR SAFE OPERATION P. 3

ENVIRONMENTAL CONDITIONS P. 7

FREEZER COMPONENTS P. 8

Control panel P. 10

INSTALLATION SITE P. 11

INSTALLATION P. 12

START-UP OF UNIT P. 13

CHAMBER TEMPERATURE SETTING P. 14

KEY LOCK FUNCTION P. 14

ALARM TEMPERATURE SETTING P. 15

SETTING OF ALARM RESUME TIME P. 16

SETTING OF COMPRESSOR DELAY TIME P. 17

ALARMS & SAFETY FUNCTIONS P. 18

ROUTINE MAINTENANCE P. 19

Cleaning of cabinet P. 19

Defrosting P. 19

TROUBLESHOOTING P. 20

DISPOSAL OF UNIT P. 21

Decontamination of unit P. 21

TEMPERATURE RECORDER (OPTION) P. 26

Setting of MTR-4015LH P. 26

Setting of MTR-G85C P. 28

BATTERY MOUNTING BOX (OPTION) P. 30

INTERFACE BOARD (OPTION) P. 30

SPECIFICATIONS P. 31

PERFORMANCE P. 32

SAFETY CHECK SHEET P. 33

2

INTRODUCTION

■ Read the operating instructions carefully before using the product and follow the instructions for safe

operation.

■ PHC Corporation takes no responsibility for safety if the product is not used as intended or is used with

any procedures other than those given in the operating instructions.

■ Keep the operating instructions in a suitable place so that they can be referred to as necessary.

■ The operating instructions are subject to change without notice for improvement of performance or

function.

■ Contact our sales representative or agent if any page of the operating instructions is lost or the page

order is incorrect, or if the instructions are unclear or inaccurate.

■ No part of the operating instructions may be reproduced in any form without the express written

permission of PHC Corporation.

IMPORTANT NOTICE

PHC Corporation guarantees this product under certain warranty conditions. However, please note that

PHC Corporation shall not be responsible for any loss or damage to the contents of the product.

3

PRECAUTIONS FOR SAFE OPERATION

It is imperative that the user complies with the operating instructions

as it contains important safety advice.

Items and procedures are described so that you can use this unit correctly and safely.

If the precautions advised are followed, this will prevent possible injury to the user and

any other person.

Precautions are illustrated in the following way:

WARNING

Failure to observe WARNING signs could result in a hazard to personnel

possibly resulting in serious injury or death.

CAUTION

Failure to observe CAUTION signs could result in injury to personnel and

damage to the unit and associated property.

Symbol shows;

this symbol means caution.

this symbol means an action is prohibited.

this symbol means an instruction must be followed.

Be sure to keep the operating instructions in a place accessible to users of this unit.

< Label on the unit >

This mark is labeled on the cover in which the electrical components of high voltage

are enclosed to prevent the electric shock.

The cover should be removed by a qualified engineer or a service personnel only.

4

PRECAUTIONS FOR SAFE OPERATION

Do not use the unit outdoors. Current leakage or electric shock may result if the unit is exposed to

rain water.

Only qualified engineers or service personnel should install the unit. The installation by

unqualified personnel may cause electric shock or fire.

Install the unit on a sturdy floor and take an adequate precaution to prevent the unit from

turning over. If the floor is not strong enough or the installation site is not adequate, this may result

in injury from the unit falling or tipping over.

Never install the unit in a humid place or a place where it is likely to be splashed by water.

Deterioration of the insulation may result which could cause current leakage or electric shock.

Never install the unit in a flammable or volatile location. This may cause explosion or fire.

Never install the unit where acid or corrosive gases are present as current leakage or electric

shock may result due to corrosion.

Always ground (earth) the unit to prevent electric shock. If the power supply outlet is not

grounded, it will be necessary to install a ground by qualified engineers.

Never ground the unit through a gas pipe, water main, telephone line or lightning rod. Such

grounding may cause electric shock in the case of an incomplete circuit.

Connect the unit to a power source as indicated on the rating label attached to the unit. Use

of any other voltage or frequency other than that on the rating label may cause fire or electric shock.

Never store volatile or flammable substances in this unit if the container cannot be sealed. These

may cause explosion or fire.

Do not insert metal objects such as a pin or a wire into any vent, gap or any outlet on the unit.

This may cause electric shock or injury by accidental contact with moving parts.

Use this unit in safe area when treating the poison, harmful or radiate articles. Improper use

may cause bad effect on your health or environment.

Turn off the power switch (if provided) and disconnect the power supply to the unit prior to

any repair or maintenance of the unit in order to prevent electric shock or injury.

Do not touch any electrical parts (such as power supply plug) or operate switches with a wet

hand. This may cause electric shock.

Do not place this unit in a location where it is difficult to disconnect the power supply plug.

Failure to disconnect the power supply plug may cause fire in the event of a problem or malfunction.

WARNING

5

PRECAUTIONS FOR SAFE OPERATION

Ensure you do not inhale or consume medication or aerosols from around the unit at the time of

maintenance. These may be harmful to your health.

Never splash water directly onto the unit as this may cause electric shock or short circuit.

Never put containers with liquid on the unit as this may cause electric shock or short circuit when

the liquid is spilled.

Never bind, process, or step on the power supply cord, or never damage or break the power

supply plug. A broken supply cord or plug may cause fire or electric shock.

Do not use the supply cord if its plug is loose. Such supply cord may cause fire or electric shock.

Never disassemble, repair, or modify the unit yourself. Any such work carried out by an

unauthorized person may result in fire, or electric shock or injury due to a malfunction.

Disconnect the power supply plug if there is something wrong with the unit. Continued

abnormal operation may cause electric shock or fire.

When removing the plug from the power supply outlet, grip the power supply plug, not the cord.

Pulling the cord may result in electric shock or fire by short circuit.

Disconnect the power supply plug before moving the unit. Take care not to damage the power

cord. A damaged cord may cause electric shock or fire.

Disconnect the power plug when the unit is not used for long periods. Keeping the connection

may cause electric shock, current leakage, or fire due to the deterioration of insulation.

If the unit is to be stored unused in an unsupervised area for an extended period, ensure that

children do not have access and that doors cannot be closed completely.

The disposal of the unit should be accomplished by appropriate personnel. Remove doors to

prevent accidents such as suffocation.

Do not put the packing plastic bag within reach of children as suffocation may result.

Flammable and explosive product. This product contains flammable refrigerant. Do not damage

or break the pipework.

This product contains flammable refrigerant. Well ventilate the room to prevent refrigerant

accumulation.

WARNING

6

PRECAUTIONS FOR SAFE OPERATION

This unit must be plugged into a dedicated circuit protected by branch circuit breaker.

Use a dedicated power source as indicated on the rating label attached to the unit. A multiple-tap

may cause fire resulting from abnormal heating.

Connect the power supply plug to the power source firmly after removing the dust on the plug.

A dusty plug or improper insertion may cause a heat or ignition.

Never store corrosive substances such as acid or alkali in this unit if the container cannot be

sealed. These may cause corrosion of inner components or electric parts.

Check the setting when starting up of operation after power failure or turning off of power

switch. The stored items may be damaged due to the change of setting.

Be careful not to tip over the unit during movement to prevent damage or injury.

Prepare a safety check sheet when you request any repair or maintenance for the safety of service

personnel.

CAUTION

7

ENVIRONMENTAL CONDITIONS

This equipment is designed to be safe at least under the following conditions (based on the IEC

61010-1):

■ Indoor use;

■ Altitude up to 2000 m;

■ Ambient temperature 5oC to 40oC;

■ Maximum relative humidity 80% for temperature up to 31oC decreasing linearly to 50% relative humidity

at 40oC;

■ Mains supply voltage fluctuations up to ±10% of the nominal voltage;

■ Transient overvoltages up to the levels of OVERVOLTAGE CATEGORY II;

■ Temporary OVERVOLTAGES occurring on the mains supply;

■ Applicable pollution degree of the intended environment (POLUTION DEGREE 2 in most cases)

8

FREEZER COMPONENTS

2

11

3

7

9

8

6

4

10

1

5

12

MDF-MU500H

MDF-MU300H

4

9

7

5

11

2

1

3

9

12

10

7

8

Power cord

Back

Power cord

Back

Fixture

Power switch

Hole for padlock

Spacer

9

FREEZER COMPONENTS

1. Keyhole: By turning to 180 degree to counterclockwise with a key, the door can be locked.

2. Handle: To open the door, grip the handle.

3. Door: Always grip the handle to open the door.

4. Leveling foot: Serves to adjust the height and to settle the frame evenly.

5. Caster: 4 casters are provided for easy movement. Separate the front two casters from the floor by

adjusting the leveling feet at the time of installation.

6. Defrost water vessel & storage container (MDF-MU300H only): The storage container can be used

to collect the defrosted water when defrosting.

Note: Move the storage items in the storage container when defrosting since the storage container is

used as a defrost water vessel.

7. Storage container: Made of styrol resin. Be careful not to damage the storage container by a metal

scraper at the time of defrosting.

Note: Do not pull the storage container excessively. The storage container may fall down.

8. Access port: This is used for leading a sensor or a cable of the measuring equipment to the chamber.

9. Door latch: To lock the door, turn the door latch downward. A padlock is also available.

10. Space for temperature recorder: A temperature recorder (optional component) can be attached

here. See page 26 “Temperature recorder”.

11. Control panel: To display the temperature setting and running condition. See page 10 for details.

12. Space for battery mounting box: A battery mounting box (optional component) can be attached

here.

10

FREEZER COMPONENTS

Control panel

1. Alarm lamp (ALARM): This lamp is flashed when unit is in alarm status. See page 18.

2. Digital temperature indicator: Normally, the current chamber temperature or set temperature is

displayed. In alarm status, an error code and chamber temperature is displayed alternately. See page

18.

3. Numerical value shift key ( ): Pressing this key in the setting mode causes the numerical value to

shift. ON-OFF of key lock can be selected by pressing this key in the key lock setting mode.

4. Digit shift key ( ): Pressing this key in the setting mode causes the changeable digit to shift. Key

lock setting mode is led by pressing this key for more than 5 seconds in the temperature display mode.

Refer to page 14 for the key lock.

5. Set key (SET): Chamber temperature setting mode is led by pressing this key. The changeable digit

is flashed. Pressing this key again after temperature setting memorizes the setting.

6. Defrost key (DEF): By pressing this key for 5 seconds, the refrigerating operation is stopped.

Pressing this key again after defrosting leads resumption of the refrigerating operation. See page 19 for

the details.

Note: The refrigerating operation never resume automatically after defrosting.

7. Alarm buzzer stop key (BUZZER): To silence the audible alarm, press this key.

8. Alarm test key (ALARM TEST): Test key for alarm device. By pressing this key, the alarm lamp

blinks, remote alarm is activated and buzzer sounds. This means all alarm function operate correctly.

Note: The remote alarm terminal is not provided with the freezer. It is enclosed in the battery mounting

box (MPR-48B1) offered as an optional component.

2

8 7 6 5 4

1

3

11

INSTALLATION SITE

To operate this unit properly and to obtain maximum performance, install the unit in a location with the

following conditions:

■ A location not subjected to direct sunlight

Do not install the unit under direct sunlight. Installation in a location subjected to direct sunlight cannot

obtain the intended performance.

■ A location with adequate ventilation

Leave at least 10 cm around the unit for ventilation. Poor ventilation will result in a reduction of the

performance and consequently the failure.

For MDF-MU500H, avoid the direct air flow by the air conditioner to the back side because the wire

condenser is on the back.

■ A location away from heat generating sources

Avoid installing the unit near heat-emitting appliances such as a heater or a boiler etc. Heat can

decrease the intended performance of the unit.

■ A location with little temperature change

Install the unit under stable ambient temperature. The allowable ambient temperature is between 5oC

and 30oC.

■ A location with a sturdy and level floor

Always install the unit on a sturdy and level floor. The uneven floor or tilted installation may cause

failure or injury. Install the unit in stable condition to avoid the vibration or noise. Unstable condition

may cause vibration or noise.

WARNING

Install the unit on a sturdy floor. If the floor is not strong enough or the installation site is not

adequate, this may result in injury from the unit falling or tipping over.

Select a level and sturdy floor for installation. This precaution will prevent the unit from tipping.

Improper installation may result in water spillage or injury from the unit tipping over.

■ A location not prone to high humidity

Install the unit in the ambient of 80% R.H. or less humidity. Installation under high humidity may cause

current leakage or electric shock.

WARNING

Do not use the unit outdoors. Current leakage or electric shock may result if the unit is exposed to

rain water.

Never install the unit in a humid place or a place where it is likely to be splashed by water.

Deterioration of the insulation may result which could cause current leakage or electric shock.

■ A location without flammable or corrosive gas

Never install the unit in a flammable or volatile location. This may cause explosion or fire or may result

in the current leakage or electric shock by the corrosion of the electrical components.

■ A location without the possibility of anything fall

Avoid installing the unit in the location where anything can fall down onto the unit. This may cause the

breakdown or failure of the unit.

12

INSTALLATION

1. Removing the packaging materials and tapes

Remove all transportation packaging materials and tapes. Open the doors and ventilate the unit. If the

outside panels are dirty, clean them with a diluted neutral dishwashing detergent. (Undiluted detergent

can damage the plastic components. For the dilution, refer to the instruction of the detergent.) After

the cleaning with the diluted detergent, always wipe it off with a wet cloth. Then wipe off the panels with

a dry cloth.

Note:

Remove the cable tie banding the power supply cord.

Prolonged banding may cause the corrosion of the cord

coating.

2. Adjusting the leveling foot

Extend the leveling feet by rotating them as shown in

the figure until the front casters are separate from the

floor. Ensure the unit is level.

3. Keeping the space (MDF-MU500H only)

Keep the adequate space at the back of the unit by using

the spacer on the back. To fix the spacer, follow the

procedure below.

- Press the spacer to the condenser.

- Pull up the lower edge to the horizontal position.

- Push in the spacer between the condenser.

4. Fixing the unit

Two fixtures are attached to the rear of the frame. Fix

the frame to the wall with these fixtures and rope or

chain.

5. Ground (earth)

The ground (earth) is for preventing the electric shock in the case of the electrical insulation is somehow

degraded. Always ground the unit at the time of installation.

WARNING

Use a power supply outlet with ground (earth) to prevent electric shock. If the power supply outlet is

not grounded, it is necessary to install a ground by qualified engineers.

Never ground the unit through a gas pipe, water main, telephone line or lightning rod. Such

grounding may cause electric shock in the case of an incomplete circuit.

Leveling foot

Spacer

13

START-UP OF UNIT

Follow the procedures for the initial and consequent operations of the unit.

1. Connect the power cord to the dedicated outlet with appropriate rating with the chamber empty and

turn on the power switch.

2. Turn on the battery switch when the battery mounting box (optional component) is installed.

3. The alarm buzzer sometimes operates. In this case, silence the buzzer by pressing the alarm buzzer

stop key (BUZZER).

4. Set the chamber temperature to the desired temperature.

5. Allow the chamber temperature to fall to the desired temperature. Check the chamber temperature

on the digital temperature indicator.

6. Press the alarm test key (ALARM TEST) and check that the alarm lamp blinks and alarm buzzer

activates. Also, the remote alarm is activates when the battery mounting box (optional component) is

installed.

Note:

The alarm lamp blinks and E09 is displayed on the digital temperature indicator when the battery switch is

OFF.

7. Begin slowly placing items into the chamber to minimize the temperature rise. The temperature alarm

activates by the temperature rise when the large amount of items are stored in the chamber at one time.

Operation after power failure

The chamber temperature setting and alarm temperature setting are backed-up by nonvolatile memory.

Accordingly, the freezer resumes the operation with setting before power failure.

CAUTION

The start-up after power failure is subject to adverse affection such as voltage drop because all electrical

appliance start to operate simultaneously. Always check the running status.

14

CHAMBER TEMPERATURE SETTING

Table 1 shows the basic procedure for setting the chamber temperature. Perform key operations in the

sequence indicated in the table. The example in the table is based on the assumption that the desired

temperature is -25oC.

Note: The unit is set at the factory that the set temperature is -30oC.

Table 1 Basic operation sequence (Example: Chamber temperature -25oC)

Description of operation Key operated Indication after operation

1 ---- The current chamber temperature is

displayed.

2 Press set key. SET The second digit of the digital

temperature indicator flashes.

3

Set the temperature to 25 with the

digit shift key and the numerical

value shift key.

By pressing the key, settable digits

is shifted.

By pressing the key, the figure of

settable digit changes.

4 Press set key. SET

Set temperature is memorized and the

current chamber temperature is

displayed.

 The setting mode returns to the temperature display mode automatically when 90 seconds has passed

without any key operation. In this case, any setting before pressing set key (SET) is not memorized.

KEY LOCK FUNCTION

This unit is provided with the key lock function. When the key lock is ON, change of temperature setting

through the key pad is not available. The defrost key (DEF) is also ineffective. The key lock is set in

OFF at the factory.

Display Mode Function

L 0 Key lock is OFF Enable to change of temperature setting

L 1 Key lock is ON Disable to change of temperature setting

Table 2 Procedure for key lock setting (change from key lock OFF to key lock ON)

Description of operation Key operated Indication after operation

1 ---- The current chamber temperature is

displayed.

2 Press digit shift key for 5 seconds.

The first digit is flashed.

3 Press numerical value shift key and

scroll the figure to 1.

When pressed, the figure of settable

digit changes.

4 Press set key. SET

The key lock is set to ON.

The current chamber temperature is

displayed.

 The setting mode returns to the temperature display mode automatically when 90 seconds has passed

without any key operation. In this case, any setting before pressing set key (SET) is not memorized.

15

ALARM TEMPERATURE SETTING

This unit is provided with both high and low temperature alarms. The temperature at which the alarm is

activated can be changed.

Note: The temperature alarm is set at ±10oC of the chamber set temperature at the factory.

Display Mode Available set range

F01 High temperature alarm set between 5oC and 15oC higher than the chamber set temperature

F02 Low temperature alarm set between 5oC and 15oC lower than the chamber set temperature

As an example, Table 3 shows the procedure to set the high temperature alarm so that the alarm can

activate when the chamber temperature is 5oC higher than the set temperature.

Table 4 shows the procedure to set the low temperature alarm so that the alarm can activate when the

chamber temperature is 5oC lower than the set temperature.

Table 3 Procedure for setting high temperature alarm

Description of operation Key operated Indication after operation

1 ---- The current chamber temperature is

displayed.

2 Press numerical value shift key for

5 seconds.

The first digit is flashed.

3 Press numerical value shift key and

scroll the figure to 1.

When pressed, the figure of settable

digit changes.

4 Press set key. SET The first digit is flashed.

5

Set the temperature to 005 with the

digit shift key and numerical value

shift key.

When pressed, the changeable digit

is shifted.

When pressed, the figure of settable

digit changes.

6 Press set key. SET

Alarm temperature is memorized and

the current chamber temperature is

displayed.

Table 4 Procedure for setting low temperature alarm

Description of operation Key operated Indication after operation

1 ---- The current chamber temperature is

displayed.

2 Press numerical value shift key for

5 seconds.

The first digit is flashed.

3 Press numerical value shift key and

scroll the figure to 2.

When pressed, the figure of settable

digit changes.

4 Press set key. SET The first digit is flashed.

5

Set the temperature to -05 with the

digit shift key and numerical value

shift key.

When pressed, the changeable digit

is shifted.

When pressed, the figure of settable

digit changes.

6 Press set key. SET

Alarm temperature is memorized and

the current chamber temperature is

displayed.

 The setting mode returns to the temperature display mode automatically when 90 seconds has passed

without any key operation. In this case, any setting before pressing set key (SET) is not memorized.

16

SETTING OF ALARM RESUME TIME

The alarm buzzer and remote alarm are stopped by pressing alarm buzzer stop key (BUZZER) on the

control panel during alarm condition. The buzzer and remote alarm will be activated again after certain

suspension if the alarm condition is continued. The suspension time can be set by following the

procedure shown in the Table 5 below.

The example in the table is based on the assumption that the desired duration is 20 minutes.

Note: The duration is set in 30 minutes at the factory.

Table 5 Setting procedure for alarm resuming time (change from 30 minutes to 20 minutes)

Description of operation Key operated Indication after operation

1 ---- The current chamber temperature is

displayed.

2 Press numerical value shift key for

5 seconds.

The first digit is flashed.

3

Set the figure to F25 with the

digit shift key and numerical value

shift key.

When pressed, the changeable digit

is shifted.

When pressed, the figure of settable

digit changes.

4 Press set key. SET The current resume time is displayed.

The second digit is flashed.

5 Set the figure to 020 with the

numerical value shift key.

When pressed, the figure of settable

digit changes.

6 Press set key. SET

The setting is memorized and

the current chamber temperature is

displayed.

 The settable alarm resume time are 10, 20, 30, 40, 50, or 60 minutes (The setting is 010, 020, 030,

040, 050, or 060). The buzzer and remote alarm would not resume if the resume time is set in 000.

 The setting of alarm resume time cannot be changed during the defrosting.

 The setting mode returns to the temperature display mode automatically when 90 seconds has passed

without any key operation. In this case, any setting before pressing set key (SET) is not memorized.

17

SETTING OF COMPRESSOR DELAY TIME

The delay time of low stage side compressor can be set to reduce the load on the power line and to

facilitate the start-up (reset) of the freezer after power failure.

The example in the table is based on the assumption that the delay time is changed to 4 minutes. The

delay time is set to 1 minutes at the factory.

Note:

■ The setting range for delay time is between 1 and 15 minutes. The cool down of chamber temperature

may be slow when the setting of delay time is over 5 minutes, depending on the installation environment.

There is no need of changing the delay time when the capacity of power source is enough.

Table 6 Changing procedure for delay time (change from 1 minutes to 4 minutes)

Description of operation Key operated Indication after operation

1 ---- The current chamber temperature is

displayed.

2 Press numerical value shift key for

5 seconds.

The first digit is flashed.

3 Set the figure to F05 with the

numerical value shift key.

When pressed, the figure of settable

digit changes.

4 Press set key. SET The current delay time is displayed.

The first digit is flashed.

5 Set the figure to 004 with the

numerical value shift key. When pressed, the figure of the first

digit changes.

6 Press set key. SET

The delay time is memorized and

the current chamber temperature is

displayed.

 The setting mode returns to the temperature display mode automatically when 90 seconds has passed

without any key operation. In this case, any setting before pressing set key (SET) is not memorized.

18

ALARMS & SAFETY FUNCTIONS

This unit has the alarms and safety functions shown in Table 7, and also self diagnostic functions.

Table 7 Alarms and safety functions

Alarm & Safety Situation Indication Buzzer Safety operation

High temperature

alarm

If the chamber temperature is higher

than the temperature at which the

high temperature alarm is activated.

Alarm lamp is flashed.

Digital temperature indicator

is flashed.

Intermittent tone with

15 minutes delay.

Remote alarm with 15

minutes delay.

Low temperature

alarm

If the chamber temperature is lower

than the temperature at which the

low temperature alarm is activated.

Alarm lamp is flashed.

Digital temperature indicator

is flashed.

Intermittent tone with

15 minutes delay.

Remote alarm with 15

minutes delay.

Auto-return When there is no key pressing in

each setting mode for 90 seconds.

Chamber temperature is

displayed. ----- Finishing of each

setting mode.

Key lock When the key lock is “ON”. ----- -----

Change of setting is

disable. Defrost key is

ineffective.

Thermal sensor

abnormality

If the thermal sensor is

disconnected.

Alarm lamp is flashed.

E01 and chamber temp. are

displayed alternately.

Intermittent tone Remote alarm.

Continuous running.

If the thermal sensor is

short-circuited.

Alarm lamp is flashed.

E02 and chamber temp. are

displayed alternately.

Intermittent tone Remote alarm.

Continuous running.

Power failure alarm

(MPR-48B1

installed)

In the case of power failure.

When the power to the unit is

disconnected.

Alarm lamp is flashed. Intermittent tone Remote alarm.

Battery check

(MPR-48B1

installed)

When about 3 years has passed with

the power cord is connected to the

outlet.

F1 and chamber temp. are

displayed alternately.

Battery switch

check

(MPR-48B1

installed)

When battery switch is OFF at the

time of alarm test.

Alarm lamp is flashed.

E09 is flashed. ----- Remote alarm.

 The above power failure alarm, battery check and battery switch check are available when the battery

mounting box (optional component) is installed. The operation is as follows:

• The power failure alarm is available when the battery switch is ON and the battery is charged. Only

the remote alarm is activated when the battery switch is OFF or the battery is discharged.

• The power failure alarm can be kept about twelve hours with the battery charged completely. 2-day

operation of the freezer is needed to charge the battery full with the battery switch ON.

• The remote alarm is stopped by pressing the alarm buzzer stop key (BUZZER) as the remote alarm

is operated in conjunction with the buzzer, except for the power failure alarm.

• During power failure, the alarm buzzer is stopped by pressing the alarm buzzer stop key (BUZZER)

but the alarm lamp keeps blinking.

 The battery for power failure alarm is an article for consumption. It is recommended that the battery

will be replaced about every three years. Contact our sales representative or agent at the time of

replacement of the battery for recycling.

La page charge ...

Phcbi MDF-MU300H Mode d'emploi

Ce manuel convient également à

Phcbi MDF-MU300H Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents