Bercomac 700310-5 Manuel utilisateur

1

Kimpex

Two Stage 48" Snowblower

For

ALL TERRAIN VEHICLES

CAUTION:

READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE

OPERATING YOUR EQUIPMENT

104303 G-06

* ASSEMBLY * REPAIR PARTS

* OPERATION * MAINTENANCE

OWNER’S MANUAL

Model Number

058121

700310-5

2

Conditions and Products Covered:

KIMPEX guarantees any part of the product or accessory

manufactured by KIMPEX and found in the reasonable

judgment of KIMPEX to be defective in material and or

workmanship will be repaired or replaced by an authorized

dealer without charge up to our maximum labor rates and pre-

established times. For replacement parts only standard

ground freight services are covered. This warranty extends to

the original retail purchaser only and is not transferable to any

subsequent purchasers.

Warranty Period

(from date of the original retail purchase):

• Residential use: 1 year

• Commercial or rental use: 90 days

Exceptions Noted Below: the following items are guaranteed

by the original manufacturer and have their own warranty,

conditions and limited time.

• Tire Chains: 90 days

• Engines (supplied with KIMPEX equipment): 2 years

Please refer to the engine manufacturer’s warranty

statement included with the unit. KIMPEX is not authorized

to handle warranty adjustments on engines.

Items and Conditions NOT Covered:

This warranty does not cover the following:

• Pick-up or delivery charges or in-home services fees.

• Any damage or deterioration of the unit, parts and or finish

of these due to normal use, wear and tear, or exposure.

• Cost of regular use or maintenance service or parts, such

as gas, oil, lubricants, tune-up parts, and adjustments.

• Any part or accessory which has been altered, modified,

misused, neglected, accidentally damaged or not properly

installed, maintained, stored or repaired not in accordance

with the instructions in the owner’s manual.

• Repair due to normal wear and or any wear items such as

shear pins, bolts, belts, etc.

• Expedited freight fee services for replacement parts.

• Shear bolts and shear pins are to be considered as a

preventive measure not as an assured protection, any

damages resulting from the lack of shear bolts breakage

are not covered.

NOTE: All warranty work must be performed by an authorized

dealer using original (manufacturer) replacement parts.

Owner’s Responsibilities:

KIMPEX’s defective equipment or part must be returned to an

authorized dealer within the warranty period for repairs. In the

event that defective merchandise must be returned to

manufacturer for repairs, freight fees are prepaid and a written

authorization from KIMPEX must be obtained by KIMPEX prior

to the shipment. This warranty extends only to equipment

operated under normal conditions. To validate a warranty

claim, it is the user’s responsibility to maintain and service the

unit as specified in the owner’s manual at their expense.

General Conditions:

The sole liability of KIMPEX with respect to this warranty shall

be strictly and exclusively repair and replacement as

mentioned herein. KIMPEX shall not have any liability for any

other costs, loss or damage, including but not limited to, any

incidental or consequential loss or damage.

In particular, without being limited to, KIMPEX shall have no

liability or responsibility for:

• Travel time, overtime, after hours time or other extraordinary

repair charges or relating to repairs and or replacements

outside of normal business hours.

• Rental of like or similar replacement equipment during the

period of any, repair or replacement work.

• Any communicating or travel charges.

• Loss or damage to person or property other than that

covered by the terms of this warranty.

• Any claims for lost revenue, lost profit or any similar costs

as a result of damage or repair.

• Attorney’s fees.

KIMPEX’s responsibility in respect to claims is limited to

making the required repairs or replacement without charge up

to our maximum labor rates and pre-established times and no

claim of breach of warranty shall be cause for cancellation or

rescission of the contract of sale of any product or accessory.

This warranty gives you specific legal rights. You may also

have other rights, which vary from state to state.

Note: KIMPEX reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify

any product previously manufactured.

Instructions for Obtaining Warranty Services:

Contact dealer where equipment was purchased or any other KIMPEX Service Dealer to arrange service at their dealership. To locate

a dealer convenient to you, access our website at www..kpx-kimpex.com.

Kimpex Inc., 5355, St-Roch, Drummundville, QC, Canada J2B 6V4

Bring the product and your proof of purchase (sales receipt) to the KIMPEX dealer.

LIMITED WARRANTY

1

TABLE OF CONTENTS

INTRODUCTION .................................................................................................................................................... 2

SAFETY PRECAUTIONS ...................................................................................................................................... 3

SAFETY DECALS .................................................................................................................................................. 5

ASSEMBLY

Step 1: Snowblower Preparation ............................................................................................................ 6

Step 2: Subframe Preparation ................................................................................................................. 9

Step 3: Engine Installation ....................................................................................................................... 11

Step 4: Installation on the vehicle ............................................................................................................ 17

OPERATION

Operating the Snowblower ....................................................................................................................... 20

Controls ..................................................................................................................................................... 20

Removing Snow ........................................................................................................................................ 20

MAINTENANCE

Maintenance .............................................................................................................................................. 21

Adjustments .............................................................................................................................................. 21

Lubrication ................................................................................................................................................. 21

Cutting Edge Maintenance ....................................................................................................................... 21

Shear Bolt Replacement .......................................................................................................................... 21

Storage ...................................................................................................................................................... 21

BELT REPLACEMENT & ADJUSTMENTS .......................................................................................................... 22

TROUBLESHOOTING ........................................................................................................................................... 23

MOUNTING BRACKET CHART ............................................................................................................................ 25

TORQUE SPECIFICATION TABLE ...................................................................................................................... 27

PARTS BREAKDOWN AND PARTS LIST

Rotation System with Chute ..................................................................................................................... 28

Manual Clutch Mechanism ....................................................................................................................... 30

Subframe ................................................................................................................................................... 32

Snowblower ............................................................................................................................................... 34

OPTIONS & ATTACHMENTS ……. ...................................................................................................................... 38

PAGE

2

INTRODUCTION

TO THE PURCHASER

This new attachment was carefully designed to give years of dependable service. This manual has been provided to

assist in the safe operation and servicing of your attachment.

NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but

are intended for reference only and are based on the latest product information available at the time of publication.

Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to use.

Carefully read, understand and follow these recommendations and insist that they be followed by those who will use

this attachment.

THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS MANUAL

THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH. DANGER,

WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF HAZARD.

HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions are

not followed.

WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are not

followed.

CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are not

followed.

Record your attachment serial number and purchase date in the section reserved below (there is no serial number on

the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement

parts. Use only genuine parts when replacements are required.

If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer

for warranty service.

This manual should be kept for future reference.

Please check if you have received all the parts for your kit with the list of the

bag and the list of the box.

7

SERIAL NUMBER : ___________________________

PURCHASE DATE : ___________________________

In this manual, right and left sides are determined by sitting on the vehicle seat facing forward.

3

SAFETY PRECAUTIONS

Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle.

and snowblower. This snowblower is capable of amputating hands and feet and throwing objects. Failure to observe

the following safety instructions could result in serious injury. All operators, no matter how experienced they may be,

should read this and other manuals related to the vehicle and attachments before operating. It is the owner's legal

obligation to instruct all operators in safe operation of the snowblower.

TRAINING:

This symbol, "Safety Alert Symbol", is used

throughout this manual and on the snowblower’s

safety labels to warn of the possibility of serious

injury. Please take special care in reading and

understanding the safety precautions before

operating the snowblower or the vehicle.

1. Read this owner's manual carefully. Be thoroughly

familiar with the controls and proper use of the

vehicle and snowblower. Know how to stop the

unit and disengage the controls quickly.

2. Never allow children to operate snowblower nor the

vehicle. Never allow adults to operate snowblower

nor the vehicle without proper instructions.

3. No one should operate the vehicle nor the

snowblower while intoxicated or while taking

medication that impairs the senses or reactions.

4. Keep the area of operation clear of all persons,

particularly small children and pets.

PREPARATION:

1. Thoroughly inspect the area where the

snowblower is to be used and remove door mats,

all foreign objects and the like.

2. Disengage all clutches and shift into neutral before

starting engine.

3. Do not operate the snowblower without wearing

adequate winter outer garments. Avoid loose fitting

clothing that can get caught in moving parts. Wear

footwear that will improve footing on slippery

surfaces.

4. Handle fuel with care, it is highly flammable.

a) Use approved fuel container.

b) Never add fuel to a running engine or hot engine.

c) Fill fuel tank outdoors with extreme care. Never

fill fuel tank indoors.

d) Never fill containers inside a vehicle, or on a

truck or a trailer bed with a plastic liner.

Always place containers on the ground, away

from your vehicle, before filling.

7

OPERATION:

1. Do not put hands or feet near or under rotating

parts. Keep clear of the discharge opening at all

times.

2. Exercise extreme caution when operating on or

crossing gravel drives, walks or roads. Stay alert for

hidden hazards or traffic.

3. After striking a foreign object, stop the engine

(motor), disconnect the wire from the spark plug(s)

and keep wire away to prevent accidental starting.

Thoroughly inspect the snowblower for any damage

and repair damage before restarting and operating

the snowblower.

e) When practical, remove gas-powered equipment

from the truck or trailer and refuel it on the

ground. If this is not possible, then refuel such

equipment on a trailer with a portable container,

rather than from a gasoline dispenser nozzle.

f) Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times, until

refueling is complete. Do not use a nozzle lock-

open device.

g) Replace fuel cap securely and wipe up spilled

fuel.

h) If fuel is spilled on clothing, change clothing

immediately.

5. Adjust the height of the snowblower to clear gravel or

crushed rock surface. This is done by adjusting the

skid shoes.

6. Never attempt to make any adjustments while the

engine (motor) is running (except when specifically

recommended by manufacturer).

7. Let engine (motor) of the vehicle and snowblower

adjust to outdoor temperatures before starting to

clear snow.

8. Always wear safety glasses or eye shields during

operation or while performing an adjustment or

repair to protect eyes from foreign objects that may

be thrown from the machine.

9. Never modify the snowblower or any part

without the written consent from the

manufacturer.

4

SAFETY PRECAUTIONS

4. If the unit should start to vibrate abnormally, stop the

engine (motor) and check immediately for the cause.

Vibration is generally a warning of trouble.

5. Stop the engine (motor) whenever you leave the

operating position, before unclogging the impeller/

collector housing or discharge chute, and when

making repairs, adjustments or inspections.

6) Take all possible precautions when leaving the

machine unattended. Disengage the power take-off,

lower the attachment, set the parking brake, stop the

engine and remove the key.

7. When cleaning, unclogging, repairing or inspecting,

the snowblower and vehicle, make certain the

collector/impeller and all moving parts have

stopped. Disconnect wire from the spark plug(s) and

keep wire away to prevent accidental starting.

8. Do not run the engine indoors, except when starting

the engine and for transporting the snowblower in or

out of the building. Do not operate or let motor run in

a storage area without ventilation because gas

contains carbon monoxide which is odourless,

colorless and can cause death.

9. Do not clear snow across the face of slopes; go up

and down. Exercise extreme caution when

changing direction on slopes. Do not attempt to

clear steep slopes.

10.Never operate the snowblower without proper

guards, plates, or other safety protective devices

in place.

11.Never direct discharge at bystanders or operate

the snowblower near glass enclosures,

automobiles, window wells, drop-offs, and the like

without proper adjustment of the snow discharge

angle. Never allow anyone including children and

pets in the clearance area.

12.Do not overload the machine capacity by

attempting to clear snow at too fast a rate. Let the

snowblower ingest snow at its own rate.

13.Never operate the snowblower at high transport

speeds on slippery surfaces. Look behind and use

care when backing.

14.Do not carry passengers.

15.Disengage power to the collector/impeller to stop

all rotating parts when the snowblower is

transported or not in use.

WHENEVER YOU SEE THIS SYMBOL

7

IT MEANS:

WARNING!

BECOME ALERT !

YOUR SAFETY IS INVOLVED!

16.Use only accessories approved by the

manufacturer of the snowblower (such as wheel

chains, and the like).

17.Never operate the snowblower without good

visibility or light.

CLEARING A CLOGGED DISCHARGE CHUTE:

Hand contact with the rotating impeller inside the

discharge chute is the most common cause of injury

associated with snowblowers. Never use your hand to

clean out the discharge chute.

To clear the chute:

1. Lower snowblower to the ground and set parking

brake.

2. SHUT THE ENGINE OFF & REMOVE KEY!

3. Wait 10 seconds to be sure the all moving parts

such as the impeller blades have stopped moving.

4. Disconnect wire from the spark plug(s) and keep

wire away to prevent accidental starting.

5. Always use a clean-out tool of at least 36” in

length, NOT YOUR HANDS.

MAINTENANCE AND STORAGE

1. Check shear bolts, engine mounting bolts, and

other bolts at frequent intervals for proper

tightness to be sure the snowblower is in safe

working condition.

2. Never store the machine with fuel in the fuel tank

inside a building where ignition sources are

present such as hot water and space heaters,

clothes dryers, and the like. Allow the engine to

cool before storing in any enclosure.

3. Always refer to the owner’s manual for the motor

and snowblower when they are to be stored for

an extended period.

4. Maintain or replace safety and instruction labels,

as necessary.

5. Run the snowblower a few minutes after throwing

snow to prevent freeze-up of the rotating parts

such as collector/impeller.

5

SAFETY DECALS

Decal # 102125 Decal # 102126

Decal # 102127 Decal # 102553

REPLACE IF DECALS ARE DAMAGED

SEE PARTS BREAKDOWN FOR DECAL LOCATION

Decal # 102671

Decal # 102128

6

ASSEMBLY

IMPORTANT: TORQUE ALL BOLTS ACCORDING

TO TORQUE SPECIFICATION TABLE (SEE TABLE

OF CONTENTS) WHEN STATED: TIGHTEN

FIRMLY. REFER TO PARTS BREAKDOWN

SECTION FOR PART IDENTIFICATION.

STEP 1

SNOWBLOWER PREPARATION:

Place snowblower face down.

Install the hitch (item 1) with three 7/16 x 1 1/4" bolts

(item 2), lock washers, nylon insert locknuts and a

7/16 x 1 1/4" bolt with a flat washer (item 3) over the

slot, lock washer and a nylon insert locknut as shown.

Tighten the bolts firmly.

Turn the snowblower upright.

Place the rotation ring (item 1) on top of the

snowblower (item 2) as shown.

Only one position provides a perfect fit.

Install hitch

Install rotation ring

Place snowblower face down

7

ASSEMBLY

Grease both ends of the rotation worm (item 1).

Insert the short rotation bushing (item 2) and the long

rotation bushing (item 3) as shown.

Insert the rotation worm with the short bushing in the

sleeve (item 1).

Insert the rotation worm support (item 2) on the long

bushing as shown.

Apply grease on the rotation ring (item 1).

Install the chute (item 2) with four retaining plates

(item 3) as shown.

At the rear left hand corner, secure a retaining plate

(item 3) on top and the rotation worm support (item 5)

underneath with two 1/4 x 3/4" bolts (item 4) and

flange nuts as shown.

Secure the other three retaining plates (item 3) with

six 1/4 x 1/2" bolts (item 6) and flange nuts.

Tighten the bolts firmly.

Install chute

Insert bushings on rotation worm

Install rotation worm

8

ASSEMBLY

Install the hand guard (item 1) as shown.

Secure in place with two 1/4 x 3/4" bolts (item 2) the

flatwashers and flange nuts inside.

Tighten the bolts firmly.

Install hand guard

9

ASSEMBLY

STEP 2

SUBFRAME PREPARATION:

Install the two caster wheels (item 1) to the wheel

support (item 2) as shown.

NOTE: If your vehicle is equipped with cat tracks,

do not install the chains now.

Install the two 3/16 x 32" chains (item 3) to the top of

the plate of the wheel support with a 3/8 x 1" bolt

(item 4) and a flat washer in the inside rear hole of the

wheel support.

Install three 3/8 x 3/4" bolts (item 5) in the other holes

and secure with the flange nuts.

Tighten firmly.

Install the subframe (item 2) to the wheel support

(item 1) with four 7/16 x 1" bolts (item 3), lock

washers and nuts.

Tighten the bolts firmly.

Install wheels and chains

Install the subframe to the wheel support

Install pivot support

Install the wheel support (item 1) to the snowblower’s

pivot support (item 2) with two 1" dia x 0.31" sleeves

(item 3) and two 1/2 x 1 1/2" bolts (item 4), flat wash-

ers, lock washers and nuts.

Tighten firmly.

10

ASSEMBLY

Install the subframe extension (item 2) to the

subframe (item 1) using eight 3/8 x 3/4” hex bolts

(item 3) and nylon nuts.

Tighten firmly.

NOTE: This subframe extension is adjustable in

order to install cat tracks on the vehicle.

Adjust to the appropriate length to your vehicle.

Example:

Vehicle with wheels: adjust subframe to its shortest.

Vehicle with cat tracks: adjust subframe to its longest.

OTHER VEHICULES:

Please take note that certain modifications might be

necessary to adapt the snowblower to other vehicles

with this subframe extension.

****THE MANUFACTURER’S WARRANTY

ON THE SNOWBLOWER DOES NOT

COVER THESE MODIFICATIONS.****

Install the subframe extension (item 2) to the

subframe (item 1) using eight 3/8 x 3/4” hex bolts

(item 3) and nylon nuts.

Tighten firmly.

For vehicle equipped with cat tracks:

Install the chain adaptor (item 1) on the subframe

(item 2) with two 3/8 x 1’’ hex bolts (item 3). Secure

with two 3/8’’ nylon insert lock nuts.

Attach the chains (item 4) on the top of the chain

adaptor with two 3/8 x 1 1/4’’ hex bolts (item 5) and

two flat washers (item 6) on the chain. Secure with

two 3/8’’ nylon insert lock nuts.

Install subframe extension for A.T.V.s

Install adaptor & chains

Install subframe extension for other vehicle

11

STEP 3

ENGINE INSTALLATION:

NOTE: THE RIGHT INSTALALTION OF THE ENGINE IS CRUCIAL TO THE GOOD WORKING

ORDER OF THE SNOWBLOWER.

Figure 1

Engine not in right position

Figure 2

Engine not in right position

NOTE: Figures 1 and 2 show an engine that is not

well positioned.

IMPORTANT: We recommend using a 13 H.P.

motor on this snowblower.

DO NOT USE A MOTOR BIGGER THAN A 13 HP,

THE PULLEYS AND BELTS ARE CALIBRATED

FOR A 13 HP MOTOR AND NOT BIGGER,

Remove the belt guide stopper (item 1) and the belt

guard (item 2).

ASSEMBLY

Remove belt guard

12

ENGINE INSTALLATION, (HONDA, BRIGGS &

STRATTON OR TECUMSEH) 13 HP

Install the engine on the stand, using the holes

identified as item A.

Secure with four 3/8 x 1 1/2" bolts, two flat washers

(over the slot) and nuts.

NOTE: Make sure the side of the base of the engine

is parallel with the snowblower’s body.

Tighten the bolts firmly.

Install engine

ASSEMBLY

INSTALLATION OF OTHER BRANDS OF

ENGINES:

Place the engine on a table. Measure the height (item

B) from the middle of the crank shaft to the table. Use

one of the two shims (3/4" or 1") if required, to attain

the height of 5.25". If more or less height is needed,

use a couple of flat washers.

Install the engine and shims on the stand. Choose the

set of holes that correspond with the holes at the

base of the engine.

The center of the crank shaft must be 5.75" from the

back of the snowblower.

Make sure that the base of the motor is parallel with

the snowblower frame.

Install engine

13

ASSEMBLY

After positioning the engine, the axes must be parallel

as shown in figures 1 and 2.

(Use some shims if necessary).

NOTE: It is very important that the pulleys are

aligned (as shown in the two views: back view of

the snowblower (fig. 1) and the top view of the

snowblower (fig. 2).

No adjustments can be made on the bottom

pulley (fig. 1, item 3).

Install the 2 1/2" pulley (item 2) on the motor shaft as

shown (hub towards the engine) with a 1/4" x 1/4" x 1

3/4" key so that the belts are parallel with the ruler.

Hold a ruler (fig.1, item A) on the double pulley (item

3).

Tighten the set screw firmly. Figure 1

Back view of

snowblower

Figure 2

Top view of snowblower

14

ASSEMBLY

Adjust the idler pulley as follows:

After installing the belts, you may run the engine

without the belt guard but only for the time needed to

verify the belt alignment and only under strict

supervision.

Do not approach (you or anyone else) the moving

parts. Engage and disengage the snowblower to

verify if the belts are well aligned, especially on the

idler pulley.

If necessary you can add or remove a flat washer for

final adjustment on the idler pulley (item 2).

Figure 1

Back view of snowblower

7 DANGER 7

Without the belt guard and belt guide stopper in

place, the snowblower will not stop or will stop

too slowly when you disengage the clutch.

Adjust the clutch cable (item 1). The distance (item B)

between the cable end (item 3) and the cable support

should be 1/4’’ (.250") to 5/16’’ (.312") when in the

engaged position.

If not, adjust the cable (item 1) by extending the cable

adjustment (See instructions on p.22). If the cable

adjustment is at its limit, unhook the spring (item 2)

and remove the cable end (item 3). Shorten the cable

adjustment. Cut the inner cable 1 1/4" longer than the

shield and reinstall as removed. Reinstall the cable

end with the hex socket set screw. Do not tighten too

firmly the hex socket set screw, if too tight it might cut

the inner cable.

Verify the adjustment.

NOTE: If there is not enough tension on the

spring (item 2) the belts will slip and be ruined.

NOTE: When the belt guide stopper is installed, the

belt should clear the pins (items 4) by 1/8’’ (.125")

when the clutch arm is in the engaged position.

Adjust clutch cable

15

ASSEMBLY

NOTE: The clutch arm must be engaged (pulled

towards the driver) before installing the belt guide

stopper, if not the belts will be destroyed.

Install the belt guard (item 2) and secure in place with

the rubber latch (item 1).

Install the belt guide stopper (item 3) (belts inside the

pins) and secure with lock washer and wing nut.

Disengage the clutch.

Install belt guard and belt guide stopper

7 DANGER 7

Never let the snowblower motor run without the

belt guard & belt guide stopper in place.

7 WARNING 7

TO PREVENT INJURIES:

Start the engine, engage and disengage the

clutch to be sure if functions normally.

This means when you disengage the clutch, the

snowblower will stop immediately .

16

ASSEMBLY

STEP 4

INSTALLATION ON THE VEHICULE:

Install the optional quick hitch mounting brackets

(item 1) under the vehicle. Refer to the Mounting

Bracket Chart to identify the proper bracket model for

your vehicle. (see table of contents).

Follow the mounting instructions supplied with the

mounting bracket kit.

DO NOT INSTALL THE OTHER ITEMS.

Carefully drive the vehicle over the subframe.

Hook the subframe (item 1) to the quick hitch bracket

(item 2) and secure in place with the handle locks

(item 3).

Attach the chains with the shackles (item 4) to the

vehicle ’s suspension to prevent the snowblower from

swaying side to side.

NOTE: Do not install the chains to the front

bumper of the vehicle.

Chains must be tight and crossed horizontally,

parallel to the ground as shown.

Install subframe on A.T.V

Install subframe on other vehicle

Install optional quick hitch

17

ASSEMBLY

LIFT THE SNOWBLOWER USING THE A.T.V.’S

WINCH:

NOTE: Optional kit #700269 Lift connection kit (items

1 & 2) must be used. This kit will double the winch’s

lifting and braking capacity and reduces the lifting

speed by 50%. This will prevent damage to the

snowblower’s engine.

Hook the pulley block (item 2) into the hole on the flat

bar welded on top of the snowblower (item 3).

Remove the pulley from the block to pass the winch

cable through the pulley block. Use the nylon strap

(item 1) supplied in the kit to attach the winch cable to

the vehicle's chassis.

If the winch is located lower than the pulley block on

the snowblower, attach the cable in the highest

position possible on the vehicle’s chassis.

If the winch is located higher than the pulley block on

the snowblower, attach the cable in the lowest

position possible on the vehicle’s chassis.

If snowblower doesn’t raise evenly see below for

instructions.

VERIFY IF SNOWBLOWER RAISES EVENLY

If snowblower does not raise evenly, follow these

instructions:

Loosen the eight bolts (items 1 & 2, four on each

side) which hold the push frame (item 3).

Lift the engine side of the snowblower and slide a 1

1/2" (approx.) piece of wood underneath.

Tighten the eight bolts very firmly (torque to 65 lbs/ft).

The snowblower should raise evenly. If not, repeat

the procedure using thicker or thinner pieces of wood

depending on the weight of the engine.

Install lift connection kit

Verify if the snowblower raises evenly

18

ASSEMBLY

NOTE: To install the clutch controls and the rotation

arm support on a vehicle which has a plastic rack

(item 1), you must purchase the optional kit "Control

support" (item 2).

Install the handle support (item 3) with the support

bracket (item 2) using the 1/4 x 3/4" hex. bolts and

nuts on the left hand side of the vehicle’s rack.

Choose the ideal place and make sure the hand

crank is easily accessible and does not interfere with

the steering handlebars.

Install the 1/2 x 3" handgrip (item 1) on the handle

(item 5).

Insert the handle through the hole in the handle

support (item 3).

Install the handle hook (item 6) on the rotation worm

(item 7).

Insert the hook on the rotation handle and lock in

place with a 2.5 mm hair pin (item 4).

Install the clutch holder (item 1) on the right hand side

of the vehicle’s front rack.

Identify where is the best place, making sure the

driver has easy access to the controls.

Wrap the rubber pads (item 2) over the tube if

necessary.

Install the clutch holder (item 1) on the tube over the

rubber pads with the round hole (item 3) towards the

front.

Secure with a 5/16 x 1 3/4" carriage bolt (item 4), in

the front hole. Secure with nut and tighten lightly.

The space between the bolt head and the brace is

intentional and is designed to attach the clutch

support. Install a 5/16 x 1 3/4" carriage bolt (item 6) in

the rear square hole (item 5) and secure with the

knob (item 7).

The clutch holder should be exactly 90° parallel with

the ground.

Using the support as a template, drill through the tube

and secure with two 1/4 x 1 1/4" hex bolts (item 8)

and nuts.

Tighten firmly.

Install handle

Install clutch holder

Control support

La page charge ...

Bercomac 700310-5 Manuel utilisateur

Bercomac 700310-5 Manuel utilisateur

dans d''autres langues

Documents connexes