Bercomac 700512-2 700513-2 Manuel utilisateur

Marque: Bercomac

Modèle: 700512-2 700513-2

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

BERCO

VANTAGE 66’’ & 72’’ Snowblower

For

OFF ROAD UTILITY VEHICLE

CAUTION:

READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE

OPERATING YOUR EQUIPMENT

L-01

* ASSEMBLY * REPAIR PARTS

* OPERATION * MAINTENANCE

*105598_EN*

OWNER’S MANUAL

Model Number

700512-2 66’’ Snowblower

700513-2 72’’ Snowblower

105724_EN

LIMITED WARRANTY

Bercomac Limitée

92, Fortin North, Adstock, Quebec, Canada, G0N 1S0

Conditions and Products Covered:

BERCOMAC guarantees any part of the product or accessory

manufactured by BERCOMAC and found in the reasonable

judgment of BERCOMAC to be defective in material and or

workmanship will be repaired or replaced by an authorized

dealer without charge up to our maximum labor rates and pre-

established times. For replacement parts only standard ground

freight services are covered. This warranty extends to the

original retail purchaser only and is not transferable to any

subsequent purchasers.

Warranty Period

(from date of the original retail purchase):

xResidential or semi-commercial use: 1 year

xCommercial, professional or rental use: 90 days

Exceptions Noted Below; the following items are guaranteed

by the original manufacturer and have their own warranty,

conditions and limited time:

xTire Chains: 90 days

xEngines: Will vary as per the manufacturer

Please refer to the engine manufacturer’s warranty

statement included with the unit. BERCOMAC is not

authorized to handle warranty adjustments on engines.

Items and Conditions NOT Covered:

This warranty does not cover the following:

xPick-up or delivery charges or in-home services fees.

xAny damage or deterioration of the unit, parts and or finish

of these due to normal use, wear and tear, or exposure.

xCost of regular use or maintenance service or parts, such as

gas, oil, lubricants, tune-up parts, and adjustments.

xAny part or accessory which has been altered, modified,

misused, neglected, accidentally damaged or not properly

installed, maintained, stored or repaired not in accordance

with the instructions in the owner’s manual.

xRepair due to normal wear and or any wear items such as

shear pins, bolts, belts, etc.

xExpedited freight fee services for replacement parts.

xShear bolts and shear pins are to be considered as a

preventive measure not as an assured protection, any

damages resulting from the lack of shear bolts breakage are

not covered.

NOTE: All warranty work must be performed by an authorized

dealer using original (manufacturer) replacement parts.

Owner’s Responsibilities:

Any defective equipment or part must be returned to an

authorized dealer within the warranty period for repairs. In the

event that defective merchandise must be returned to

manufacturer for repairs, the dealer must first obtain a written

authorization from either KIMPEX or BERCOMAC, freight fees

are prepaid prior to the shipment. This warranty extends only

to equipment operated under normal conditions. To validate a

warranty claim, it is the user’s responsibility to maintain and

service the unit as specified in the owner’s manual or to have

the unit serviced at their dealer at their expense.

General Conditions:

The sole liability of BERCOMAC with respect to this warranty

shall be strictly and exclusively repair and replacement as

mentioned herein. BERCOMAC shall not have any liability for

any other costs, loss or damage, including but not limited to,

any incidental or consequential loss or damage.

In particular, without being limited to, BERCOMAC shall have

no liability or responsibility for:

xTravel time, overtime, after hours time or other

extraordinary repair charges or relating to repairs and or

replacements outside of normal business hours.

xRental of like or similar replacement equipment during the

period of any, repair or replacement work.

xAny communicating or travel charges.

xLoss or damage to person or property other than that

covered by the terms of this warranty.

xAny claims for lost revenue, lost profit or any similar costs

as a result of damage or repair.

xAttorney’s fees.

BERCOMAC’s responsibility in respect to claims is limited to

making the required repairs or replacement without charge up

to our maximum labor rates and pre-established times and no

claim of breach of warranty shall be cause for cancellation or

rescission of the contract of sale of any product or accessory.

This warranty gives you specific legal rights. You may also

have other rights, which vary from state to state.

NOTE: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify

any product previously manufactured.

Instructions for Obtaining Warranty Services:

Contact dealer where equipment was purchased or any other authorized service dealer to arrange service at their dealership. Requests

for warranty claims must be carried out through the same distribution network used to purchase the product. Don't forget to bring your

proof of purchase (sales receipt) to the dealer.

TABLE OF CONTENTS

INTRODUCTION .................................................................................................................................................... 2

SAFETY PRECAUTIONS ...................................................................................................................................... 3

SAFETY DECALS .................................................................................................................................................. 5

ASSEMBLY

Tools Required .......................................................................................................................................... 6

Step 1: Snowblower Preparation ............................................................................................................ 7

Step 2: Vehicle Preparation ...................................................................................................................... 9

Step 3: Subframe Preparation .................................................................................................................. 9

Step 4: Control Box Installation ................................................................................................................ 13

Step 5: Verify Skid Shoe ........................................................................................................................... 15

Installation of the Spring ............................................................................................................. 15

OPERATION

Operating the Snowblower ....................................................................................................................... 16

Electrical Controls ..................................................................................................................................... 16

Removing Snow ........................................................................................................................................ 16

Clearing a Clogged Discharge Chute ...................................................................................................... 16

MAINTENANCE & DISMOUNTING

Maintenance .............................................................................................................................................. 17

Adjustments .............................................................................................................................................. 17

Lubrication ................................................................................................................................................. 17

Cutting Edge Maintenance ....................................................................................................................... 17

Auger and Fan Shear Bolt Replacement ................................................................................................. 17

Snowblower Pulley Replacement or Alignment ...................................................................................... 17

Dismounting .............................................................................................................................................. 18

Storage ...................................................................................................................................................... 18

BELT REPLACEMENT .......................................................................................................................................... 18

REPLACEMENT of ONE or TWO SECTIONS of the AUGER and/ or GEAR BOX .......................................... 19

TROUBLESHOOTING ........................................................................................................................................... 20

TORQUE SPECIFICATION TABLE ...................................................................................................................... 21

PARTS BREAKDOWN AND PARTS LIST

Vantage Snowblower ................................................................................................................................. 22

Subframe ................................................................................................................................................... 27

Honda Engine 24hp .................................................................................................................................. 30

Kohler Engine 23hp .................................................................................................................................. 31

Kohler Engine 27hp .................................................................................................................................. 32

OPTIONS & ACCESSORIES ……......................................................................................................................... 33

INTRODUCTION

TO THE PURCHASER

This new accessory was carefully designed to give years of dependable service. This manual has been provided to

assist in the safe operation and servicing of your attachment.

NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but

are intended for reference only and are based on the latest product information available at the time of publication.

Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to

use. Carefully read, understand and follow these recommendations and insist that they be followed by those who will

use this attachment.

THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS

MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.

DANGER, WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF

HAZARD. HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions

are not followed.

WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are

not followed.

CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are

not followed.

Record your attachment serial number and purchase date in the section reserved below (there is no serial number on

the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement

parts. Use only genuine parts when replacements are required.

If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer

for warranty service.

This manual should be kept for future reference.

Please check if you have received all the parts for your kit with the list of the

bag and the list of the box.

SERIAL NUMBER : ___________________________

(IF APPLICABLE)

MODEL NUMBER: ___________________________

PURCHASE DATE : ___________________________

SAFETY PRECAUTIONS

Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle

and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury. All operators, no matter how experienced they may be,

should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal

obligation to instruct all operators in safe operation of the accessory.

GLOSSARY:

In this manual, right and left sides are determined by

sitting on the seat of the vehicle facing forward.

In this manual, "accessories" means attachments

(snowblower, rotary broom, blade etc.) that you install

on the vehicle (lawn tractors, A.T.V. s etc).

TRAINING:

This symbol, "Safety Alert Symbol", is used

throughout this manual and on the

accessory’s safety labels to warn of the

possibility of serious injury. Please take

special care in reading and understanding

the safety precautions before operating the

vehicle and accessory.

1. Read this owner's manual carefully. Be thoroughly

familiar with the controls and proper use of the

vehicle and accessory. Know how to stop the unit

and disengage the controls quickly.

2. Never allow children to operate the vehicle nor the

accessory. Never allow adults to operate the vehicle

nor the accessory without proper instructions.

3. No one should operate the vehicle nor the

accessory while intoxicated or while taking

medication that impairs the senses or reactions.

4. Keep the area of operation clear of all people,

particularly small children and pets.

PREPARATION:

1. Thoroughly inspect the area where the accessory

is to be used and remove door mats, all foreign

objects and the like.

2. For motorized accessories, disengage all clutches

and shift into neutral before starting engine.

3. Do not operate the accessory without wearing

adequate winter outer garments. Avoid loose fitting

clothing that can get caught in moving parts. Wear

footwear that will improve footing on slippery

surfaces.

4. Handle fuel with care, it is highly flammable.

a) Use approved fuel container.

b) Never add fuel to a running engine or hot engine.

c) Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

d) Never fill containers inside a vehicle, or on a

truck or a trailer bed with a plastic liner. Always

place containers on the ground, away from your

vehicle, before filling.

e) When practical, remove gas-powered

equipment from the truck or trailer and refuel it

on the ground. If this is not possible, then refuel

such equipment on a trailer with a portable

container, rather than from a gasoline

dispenser nozzle.

f) Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times, until

refueling is complete. Do not use a nozzle lock-

open device.

g) Replace fuel cap securely and wipe up spilled

fuel.

h) If fuel is spilled on clothing, change clothing

immediately.

5. Never attempt to make any adjustments while the

engine (motor) is running (except when specifically

recommended by manufacturer).

6. Let the vehicle and accessory adjust to outdoor

temperatures before using.

7. Never use an accessory without proper guards,

plates, or other safety protective devices in place

8. Always make sure to wear the appropriate safety

equipment required (glasses, muffs, mask…) for

each type of product. See operation section.

9. Always make sure of having safe traction on the

vehicle by using the recommended accessories

(chains, A.T.V. tracks, counterweights…). See

operation section.

10. Always make sure the all components are correctly

installed. (driveline securely attached and locked at

both ends, belts properly installed…)

11. Never modif

the accessor

or an

part without

the written consent from the manufacturer.

OPERATION:

1. Do not put hands or feet near, under or inside rotating

parts.

2. Exercise extreme caution when operating on or

crossing gravel drives, walks or roads. Stay alert for

hidden hazards or traffic. Do not carry passengers.

3. After striking a foreign object, stop the engine (motor),

disconnect the wire from the spark plug(s) and keep

wire away to prevent accidental starting. Thoroughly

inspect the accessory for any damage and repair

damage before restarting and using the accessory.

4. If the unit should start to vibrate abnormally, stop the

engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

5. Take all possible precautions when leaving the

vehicle unattended. Disengage the power take-off,

lower the attachment, place the transmission into

neutral, set the parking brake, stop the engine and

remove the contact key.

6. Do not run the engine indoors, except when starting

the engine and for transporting in or out of the

building. Do not operate or let motor run in a storage

area without ventilation because gas contains

carbon monoxide which is odorless, colorless and

can cause death.

7. Never use the accessories across the face of

slopes, go from top to bottom. Exercise extreme

caution when using equipment on slopes. Do not

attempt to clear a steep slope.

8. Never tolerate bystanders in the working zone.

Never use an accessory in the direction of

bystanders, it might throw gravel or debris that can

hurt people or damage property.

9. Never operate the accessory at high transport

speeds on slippery surfaces. Use care when

backing up.

10. Do not carry passengers.

11. Disengage power to the accessory when it is

transported or not in use.

12. Never operate the accessory without good visibility

or light.

13. Keep the accessory away from heat sources or

flames.

MAINTENANCE AND STORAGE

1. When cleaning, repairing or inspecting the vehicle

and accessory, make certain that all moving parts

have stopped. For gasoline engine, disconnect wire

from the spark plug(s) and keep wire away to

prevent accidental starting.

2. Check all the bolts and components at frequent

intervals to make sure that they are properly

tightened.

3. Never store a motorized accessory with fuel in the

fuel tank inside a building where ignition sources are

present such as hot water and space heaters,

clothes dryers, and the like. Allow the engine to cool

before storing in any enclosure.

4. Always refer to the owner’s manual when you store

the accessory and vehicle for a prolonged or an

unspecified length of time.

5. Maintain or replace safety and instruction labels, as

necessary.

6 For winter accessories, (if applicable), let the engine

run for a few minutes after clean snow in order to

prevent the rotary parts from freezing.

7. Inspect the vehicle’s and accessory’s air filter (if

applicable) every day. Clean it or replace it as

necessary. Change the oil more often when working

in dusty conditions. See the vehicle’s and

accessory's owner’s manual.

THIS SYMBOL MEANS

DANGER !

BECOME ALERT !

YOUR SAFETY IS INVOLVED !

SAFETY PRECAUTIONS

SAFETY DECALS

REPLACE IF DECALS ARE DAMAGED

SEE PARTS BREAKDOWN FOR DECAL LOCATION

To avoid serious injury:

Keep hands, feet & clothing away from rotating auger

while engine is running.

To avoid serious injury:

Keep hands out of this discharge chute while engine

is running.

To avoid injury from drive belt:

Keep hands, feet & clothing away.

Do not attempt to install or remove drive belt without

reading owner’s manual.

DECAL #105126

DECAL #105128

DECAL #105127

DECAL #105130

Before installing or using:

Locate, read and make sure to understand all of the

owner’s manual.

DECAL #105131

Refer to owner’s manual about wearing safety

glasses, ear muffs and mask.

Refer to owner’s manual for use of counter weights,

cat tracks and tire chains.

1-Do not drive faster than 3 KM/H when the

snowblower is in operation.

2-Do not drive faster than 10 KM/H when the

snowblower is in the raised position.

3-The head of the snowblower weighs 220kg.

(without engine).

4-The engine wattage is 17.2kW. (depends on what

engine is installed).

5-The sound pressure level (107dBA) is measured

at the engine (full charge at 3600 RPM) and

depends on the engine that is installed. The value

indicated is a reference only.

ASSEMBLY

IMPORTANT: TORQUE ALL BOLTS ACCORDING

TO TORQUE SPECIFICATION TABLE (SEE TABLE

OF CONTENTS) WHEN STATED: TIGHTEN

FIRMLY. REFER TO PARTS BREAKDOWN

SECTION FOR PART IDENTIFICATION.

Overall view of snowblower

TOOLS REQUIRED:

1 Ratchet

3 Sockets 7/16’’, 1/2’’, 9/16’’

3 Wrenches, 7/16’’, 1/2’’, 9/16’’

1 Hexagonal wrench 5/32’’

1 Wrench (for the nuts on the vehicle’s battery posts)

ASSEMBLY

STEP 1

SNOWBLOWER PREPARATION:

Refer to parts breakdown section for parts

identification.

Install the chute (item 1).

# Item Description Action

1 Chute Place the chute on

the nylon rotation

ring. Turn the chute

to make sure it turns

freely. Place the

chute at 45° angle

as shown.

2 Hex bolt

1/4’’ n.c x 1’’

(qty 4)

Insert under the

rotation ring (item 5)

as shown.

3 Spacers

(qty 4)

Install on the bolts

between the rotation

ring and the chute.

4 Nylon insert lock

nuts 1/4’’

(qty 4)

Secure everything in

place.

Install the nylon rotation ring (item 1).

# Item Description Action

1 Rotation ring

(nylon)

Install over the opening

as shown and align the

notches.

Install the nylon rotation ring

Install the chute

Install the rotation ring (item 1).

# Item Description Action

1 Rotation ring Install over the opening

as shown.

NOTE: Place the rotation ring (item 1) approximately

as shown in the drawing, the groves of the rotation

ring on the teeth of the rotation motor.

Install the rotation ring

Install the retaining plate (item 2) under the chute .

# Item Description Action

1 Hex. bolt

1/4"n.c. x 1/2"

(qty 2)

Insert as shown.

2 Retaining plate Install as shown

under the chute

3 Nylon insert lock nut

1/4" thin

(qty 2)

Secure in place.

Install the retaining plate

ASSEMBLY

STEP 2

VEHICLE PREPARATION:

NOTE: A 1 7/8” tow hitch ball is required.

Choose among the three different options to prepare

your vehicle (A, B, C).

# Item Description Action

A) Install the lift strap (item 1) by looping it around the

suspension arm on each side of the vehicle.

Tighten the loop firmly.

B) Install the brackets (item 3) on both sides of

vehicle.

Bolt and nut from

suspension arm

Remove.

2-3 Flat washer and

bracket

Install and lightly

secure with the

original bolt and nut.

C) Install the brackets (item 4) on both sides of

vehicle.

Nut from

suspension arm

Remove.

4 Bracket Install and lightly

secure with the

original nut.

Install the lift strap or the brackets.

STEP 3

SUBFRAME PREPARATION:

NOTE: Determine according to the height of the

vehicle which set of holes to use to assemble the

wheel support (item 1) to the subframe.*

Install the wheel support (item 1).

# Item Description Action

1 Wheel support Install to the

subframe.

2 Hex bolts

3/8" x 1"(qty 4)

Insert as shown

3 Flange nuts 3/8"

(qty 4)

Tighten firmly

*The subframe must be parallel with the ground when

the subframe is installed under the vehicle.

Install the wheel support to the subframe

ASSEMBLY

Install the assembled turnbuckles (item 1).

# Item Description Action

1 Assembled

turnbuckle (qty 2)

Install on the bracket

of the subframe as

shown.

3 Flat washer

3/8" (qty 2)

Install on the

assembled

turnbuckles as shown.

3 Hex bolt

5/16" x 1"(qty 2)

Insert as shown.

4 Nylon insert lock

nut 5/16" (qty 2)

Install and tighten

loosely enough to

allow the parts to

move freely.

NOTE: Position the chains as shown and tighten

firmly.

2 Chain Install on the chains

as shown.

Install the assembled turnbuckles

Install snowblower

Install snowblower (item 1).

# Item Description Action

1 Snowblower Install to wheel

support.

2 Pin Slide pin through the

assembly to hold

everything together.

3 Hair pin

4mm

Secure the pin as

shown.

NOTE: Make sure the pin is in the locked position.

You have seven different positions on the adjustment

tube (item 1) (the adjustment tube can be inverted) to

adjust the length of the subframe.

To choose the right length, insert the adjustment tube

(item 1) into the subframe (item 2) and insert the rear

bracket (item 3) on the adjustment tube.

Do not secure.

Drive the vehicle over the subframe, make sure the

caster wheels do not touch the front wheels on the

vehicle.

Identify the right length and secure in place with the

pins (item 4) and 3mm hair pins (item 5).

Adjust the length of the subframe

ASSEMBLY

Assemble the hitch support plates

Choose between the three positions (see figure), the

height of the hitch support.

The hitch support is preassembled in one position at

the factory

There must be a maximum of ground clearance

according to your vehicle.

Position A does not have the hitch support plates

(item 1).

Assemble the hitch support plates (item 1).

# Item Description Action

1 Hitch support plate

(qty 2)

Assemble the hitch

support plates on the

hitch support.

2 Hex bolt

3/8" x 3/4"

(qty 4)

Insert in the chosen

holes, (two on each

side) and secure with

the flange nuts 3/8’’.

Tighten firmly.

3 Hitch Insert on the two

hitch supports plates

(if applicable).

4 Hex bolt 3/8 x 3"

(qty 1)

Insert in the hole as

shown and secure

with a 3/8’’ nylon lock

nut. Tighten firmly.

Install the assembled hitch support (item 1) on the

vehicle’s tow hitch ball.

# Item Description Action

1 Assembled hitch

support

Insert onto the rear

bracket.

2-3 Pin and 3mm hair

Secure in place.

4 Assembled hitch

support

Attach on the

vehicle’s tow hitch

ball.

5-6 Pin and 3mm hair

Secure in place.

Make sure the subframe does not come into contact

with vehicle at any time.

NOTE: You can turn the hitch assembly (item 1) by

removing the pin (item 2) to facilitate driving the

vehicle over the subframe.

Secure the assembled hitch support on the tow hitch

ball

ASSEMBLY

Install the turnbuckles (item 1) into the brackets or

into the lift straps.

# Item Description Action

1 Turnbuckle

(qty 2)

Adjust them so that the

subframe is centered

under the vehicle.*

*Tighten the turnbuckles firmly in order to tighten the

vehicle's suspension.

IMPORTANT: After adjusting the turnbuckles, tighten

the nuts on the vehicle’s suspension arms firmly.

Make sure to lock the nuts with the original locks. Hook the turnbuckles

Attach the vehicle’s winch’s hook on the rod on the

hitch.

# Item Description Action

If the vehicle's winch is

higher than 20" (510mm) from the ground.

1 Sleeve Install in the top hole

of the lever.

2 Hex bolt 1/2" x 2

1/4" and nylon

insert lock nut

Insert in the top

sleeve.

Tighten firmly.

Vehicle’s winch’s

hook

Install on the rod as

shown.

If the vehicle's winch is

lower than 20" (510mm) from the ground use the

sleeve welded on the hitch.

Vehicle’s winch’s

hook

Install on the rod as

shown.

Tip: Thread the winch’s hook in front of the hitch as

shown and then thread the cable over the sleeve. Install the winch hook

ASSEMBLY

STEP 4

CONTROL BOX INSTALLATION:

Install the control box

Disconnect the wires that are connected to the control

box.

# Item Description Action

1 Box support Install in an appropriate

place. Drill holes if

necessary.

2 Hex bolt 1/4’’ x

1/2’’ (qty 2)

Secure box support in

place with two flange

nuts. Tighten firmly.

3 Control box Install on the box

support.

Thread the wires that unite the accessory under the

hood to the front of the vehicle.

Thread the other wire by an appropriate route to the

battery.

Connect the red wire (item 1) to the positive post and

the black wire (item 2) to the negative post on the

vehicle's battery.

NOTE: Secure the wires to the vehicle with the nylon

tie wraps. These wires will stay on the vehicle.

IMPORTANT: The control box is equipped with a red

emergency kill switch in case you need to stop the

engine quickly.

NOTE: The emergency kill switch must be pulled out

to start the engine of the accessory.

Connect the wires on the battery

Connect the wire connector on the motor for the chute

deflector (A).

There will be one black connector that will not be

connected. This is to connect the optional

snowblower light.

Make sure the connectors are well connected

together and tie the wire that is connected to the

motor of the deflector (item A) with a nylon tie wrap

on the motor in a way that the wire does not come

into interference with the chute’s rotation.

Secure the wires as shown

ASSEMBLY

Turn the chute to its maximum towards the right.

Secure the wire of the motor for the deflector with a cou-

ple of tie wraps (item 1 & 2) as shown.

Be sure to leave enough wire length to be able to turn

the chute freely.

IMPORTANT:

Take the time to familiarize yourself with the location

of the switches and with their use.

NOTE: If the switches don’t match the right

controls, reconnect the connectors with the right

motors.

Pay particular attention to the switch for the belt

tensioner (item 3).This switch must be held in position

for a few seconds in order to activate or deactivate

the lever of the belt tensioner.

Make sure that the action is complete when you

engage or disengage the snowblower.

DANGER:

It is the responsibility of the person who installs

the accessory to make sure the engaging system

works well and that the snowblower disengages

effectively at all times. It is imperative to make the

necessary adjustments if applicable.

Identification of the switches:

1. Emergency kill switch. (Pull out to start).

2. Joystick to move the chute and the deflector.

3. Switch for the belt tensioner (to start snowblower).

4. Switch for optional light kit.

Identify the controls.

STEP 5

VERIFY SKID SHOE ADJUSTMENT:

LEVEL PAVED SURFACE: Adjust skid shoes to allow

3/16" to 1/4" clearance (A) between cutting edge and

surface.

UNEVEN OR GRAVEL SURFACE: Adjust skid shoes

to allow 1/2" to 5/8" clearance (A) between cutting

edge and surface.

ASSEMBLY

Adjust skid shoes as shown

Install the spring

INSTALLATION OF THE SPRING AND

VERIFICATION OF THE LIFTING HEIGHT OF THE

SNOWBLOWER.

IMPORTANT:

It is very important the snowblower engine does not

come into contact with the vehicle If necessary, use

on each side one or two shims (item 2) supplied with

the kit to limit the lifting height.

Install in place with a hex bolt 3/8’’ x 1 1/2’’ (item 3), a

flat washer 7/16’’ (item 4) and a nylon insert lock nut

(item 5) as shown.

Lift the snowblower to its maximum height, insert the

spring (item 1) in the chain and on the welded rod as

shown.

VERIFY TIRE PRESSURE:

Check and adjust the pressure of the tires on the

subframe at: 50psi.

Tire pressure must be even on both sides.

OPERATING THE SNOWBLOWER

a) Make sure the snowblower is clear of snow

before engaging the clutch.

b) Make sure that the auger and impeller operate

freely.

c) Start the snowblower engine.

d) Before engaging the snowblower drive, always

have the engine running at max R.P.M.

e) Operate the snowblower at maximum engine

R.P.M.

IMPORTANT: USE FULL ENGINE R.P.M. WHEN

REMOVING WET, STICKY SNOW. LOW R.P.M.

POWER WILL TEND TO PLUG THE CHUTE.

ELECTRICAL CONTROLS

See installation of the control box in order to identify the

controls.

RAISING AND LOWERING THE SNOWBLOWER:

Use the winch switch control to raise and lower the

snowblower.

OPERATION

REMOVING SNOW

When removing snow, do not use the snowblower as

a dozer blade to push snow. Allow snowblower to

ingest snow at its own speed. If the speed of your

vehicle is too fast, the snowblower may become

overloaded and plug. .

WARNING

Read the vehicle's owner’s manual carefully. Be

thoroughly familiar with the controls & proper

use of the attachment. Know how to stop the unit

& disengage the controls quickly.

WARNING

-Do not attempt to clear plugged chute, auger or

fan of snow while the snowblower's engine is

running.

-Disengage snowblower.

-Lower snowblower onto ground.

-Set the parking brake.

-Stop engine, remove the ignition key, disconnect

the wire from spark plug(s) and keep away from

spark plug(s) to prevent accidental starting.

-Make sure all moving parts have stopped.

-Do not use hand to unplug chute.

-Use a 36’’ (924 mm.) minimum length stick or

board.

WARNING

TO PREVENT INJURIES AND FOR MORE

TRACTION WHEN USING SNOWBLOWER:

-Do not drive faster than 3 km/hr (2 m/hr) with

snowblower on the ground.

-Do not drive faster than 10 km/hr (6 m/hr) with

the snowblower in raised position.

-Do not operate on a slope greater than 10°.

-Vehicle manufacturer approved tire chains are

required.

CLEARING A CLOGGED DISCHARGE

CHUTE:

Hand contact with the rotating impeller inside the

discharge chute is the most common cause of injury

associated with snowblowers. Never use your hand to

clean out the discharge chute.

To clear the chute:

1. Lower snowblower to the ground and set parking

brake.

2. SHUT THE ENGINE OFF & REMOVE KEY!

3. Wait 10 seconds to be sure the all moving parts

such as the impeller blades have stopped moving.

4. Disconnect wire from the spark plug(s) and keep

wire away to prevent accidental starting.

5. Always use a clean-out tool of at least 36” in length,

NEVER YOUR HANDS.

EMERGENCY KILL SWITCH:

Push down on the emergency button to stop the

engine.

IMPORTANT: The emergency button has to be pulled

out in order to start the snowblower engine.

MAINTENANCE

a) Check mounting bolts at frequent intervals for

proper tightness in order to prevent costly repairs.

Make sure your snowblower is in safe working

condition.

b) Provide adequate blocking before working under

the snowblower when in raised position.

ADJUSTMENTS

SKID SHOE ADJUSTMENT:

Level Paved Surface: Adjust skid shoes to allow 3/16" to

1/4" clearance between cutting edge and surface.

Uneven or Gravel Surface: Adjust skid shoes to allow

1/2" to 5/8" clearance between cutting edge and

surface.

MAINTENANCE & DISMOUNTING

WARNING

TO PREVENT INJURIES:

Stop the snowblower motor.

Apply parking brakes.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent accidental

starting.

SNOWBLOWER PULLEY REPLACEMENT

or ALIGNMENT:

Clean the parts before aligning or replacing the

pulley. Apply some "Loctite" 2760 on the key and

the set screws. Tighten firmly.

AUGERS AND FAN SHEAR BOLT

REPLACEMENT

Shear bolts are to be considered a preventive

measure and not an assured protection. Operator

vigilance is required. Thoroughly inspect the areas

where the snowblower is to be used and remove all

foreign objects.

To avoid damage to the snowblower:

Use only the original shear bolts (grooved bolts).

#105602 in bags of 10 for the augers.

#105627 in bags of 10 for the fan.

The use of any other shear bolt will not insure any

protection and may void the warranty.

IMPORTANT: IT IS VERY IMPORTANT TO REPLACE

THE AUGERS IN THE SAME POSITION AS SHOWN

IN THE DRAWING BEFORE INSTALLING THE

SHEAR BOLTS.

CUTTING EDGE MAINTENANCE

Verify from time to time the wearing on the cutting

edge to make sure you do not wear out the base of

the snowblower’s chassis. This cutting edge is

reversible. Unscrew the bolts and turn the cutting

edge, reinstall and tighten the bolts securely.

LUBRICATION

Grease the wheel axles, the fork pivots after every

sixteen hours of use.

Apply oil at all pivot points.

Chute Rotation System: Oil chute base, rotation worm

every sixteen hours of operation.

Gear box:

Check the oil annually. If necessary, add AGMA 5 EP or

SAE 90 oil.

The gear box should have a total of 155 ml of oil or filled

to the rim of the bolt hole when installed on the

snowblower. (see figure)

BELT REPLACEMENT:

For belt part number, refer to parts breakdown section

for parts identification.

a) Remove the belt guard (item 1) by removing the

two hex bolts 1/4" x 1/2" (item 2).

b) Remove the tension from the belt by pushing on

the switch for the belt tensionner.

c) Remove the belt from the engine pulley (item 3).

d) Loosen the knob (item 4) in order to free the belt

from the pulley.

e) Activate the switch for the electric motor for the

belt tensionner to release the brake (item 5).

NOTE: This step is necessary to free the belt

from the snowblower pulley.

f) Remove and install the new belt.

g) Replace the bearing on the (item 7) on the back

of the belt to keep it in the pulley (item 6) and

tighten the knob (item 4).

h) After installing the belt, you may run the engine

without the belt guard but only to verify the belt

alignment. Do not leave the snowblower without

supervision. Neither you or anyone else must

approach the moving parts. Engage and

disengage the snowblower to verify if the belt is

well aligned, especially on the idler pulley (item

8).

Make sure to hold the switch long enough so

that there is enough tension on the spring.

If necessary, you can add or remove a flat

washer on the idler pulley for final adjustments.

i) Reinstall the belt guard.

BELT REPLACEMENT

CAUTION

Never use the snowblower without the belt guard.

Belt replacement

MAINTENANCE & DISMOUNTING

DISMOUNTING

a) Select a level surface, set parking brake, stop the

engine, and remove the ignition key to prevent

accidental starting.

b) Lower the accessory to the ground.

c) Disconnect the wires that unite the accessory to

the vehicle.

d) Unhook the turnbuckles from the front of the

vehicle, (Tip: slacken one of the turnbuckles in

order to keep the adjustment), the hook from the

winch.

e) Remove the assembled hitch support from the

vehicle’s tow hitch ball.

f) Remove the vehicle.

STORAGE

a) Clean snowblower and subframe thoroughly and

repaint all parts from which paint has worn.

b) List the replacement parts that will be needed to

be replaced before the next season.

c) Follow the instructions in the Lubrication section.

d) Concerning the snowblower engine, follow the

instructions in the engine owner’s manual.

e) Store the snowblower and the subframe in a dry

place.

La page charge ...

Bercomac 700512-2 700513-2 Manuel utilisateur

Marque: Bercomac

Modèle: 700512-2 700513-2

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Bercomac 700512-2 700513-2 User manual

Bercomac 700512-2 700513-2 Manuel utilisateur

Bercomac 700512-2 700513-2 Manuel utilisateur

dans d''autres langues

Documents connexes