Bercomac 700480-1 Manuel utilisateur

Marque: Bercomac

Modèle: 700480-1

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

BERCO

VERSATILE 48" SNOWBLOWER

For

ALL TERRAIN VEHICLES

CAUTION:

READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE

OPERATING YOUR EQUIPMENT

J-01

* ASSEMBLY * REPAIR PARTS

* OPERATION * MAINTENANCE

*105225_EN*

OWNER’S MANUAL

Model Number

700480-1

105225_EN

LIMITED WARRANTY

Bercomac Limitée

92, Fortin North, Adstock, Quebec, Canada, G0N 1S0

Conditions and Products Covered:

BERCOMAC guarantees any part of the product or accessory

manufactured by BERCOMAC and found in the reasonable

judgment of BERCOMAC to be defective in material and or

workmanship will be repaired or replaced by an authorized

dealer without charge up to our maximum labor rates and pre-

established times. For replacement parts only standard ground

freight services are covered. This warranty extends to the

original retail purchaser only and is not transferable to any

subsequent purchasers.

Warranty Period

(from date of the original retail purchase):

• Residential use: 1 year

• Commercial or rental use: 90 days

Exceptions Noted Below; the following items are guaranteed

by the original manufacturer and have their own warranty,

conditions and limited time:

• Tire Chains: 90 days

• Engines (installed in factory on BERCO equipment): 2 years

• Engines (sold separately): Validate with the dealer.

Please refer to the engine manufacturer’s warranty

statement included with the unit. BERCOMAC is not

authorized to handle warranty adjustments on engines.

Items and Conditions NOT Covered:

This warranty does not cover the following:

• Pick-up or delivery charges or in-home services fees.

• Any damage or deterioration of the unit, parts and or finish

of these due to normal use, wear and tear, or exposure.

• Cost of regular use or maintenance service or parts, such as

gas, oil, lubricants, tune-up parts, and adjustments.

• Any part or accessory which has been altered, modified,

misused, neglected, accidentally damaged or not properly

installed, maintained, stored or repaired not in accordance

with the instructions in the owner’s manual.

• Repair due to normal wear and or any wear items such as

shear pins, bolts, belts, etc.

• Expedited freight fee services for replacement parts.

• Shear bolts and shear pins are to be considered as a

preventive measure not as an assured protection, any

damages resulting from the lack of shear bolts breakage are

not covered.

NOTE: All warranty work must be performed by an authorized

dealer using original (manufacturer) replacement parts.

Owner’s Responsibilities:

Any defective equipment or part must be returned to an

authorized dealer within the warranty period for repairs. In the

event that defective merchandise must be returned to

manufacturer for repairs, the dealer must first obtain a written

authorization from either KIMPEX or BERCOMAC, freight fees

are prepaid prior to the shipment. This warranty extends only

to equipment operated under normal conditions. To validate a

warranty claim, it is the user’s responsibility to maintain and

service the unit as specified in the owner’s manual or to have

the unit serviced at their dealer at their expense.

General Conditions:

The sole liability of BERCOMAC with respect to this warranty

shall be strictly and exclusively repair and replacement as

mentioned herein. BERCOMAC shall not have any liability for

any other costs, loss or damage, including but not limited to,

any incidental or consequential loss or damage.

In particular, without being limited to, BERCOMAC shall have

no liability or responsibility for:

• Travel time, overtime, after hours time or other

extraordinary repair charges or relating to repairs and or

replacements outside of normal business hours.

• Rental of like or similar replacement equipment during the

period of any, repair or replacement work.

• Any communicating or travel charges.

• Loss or damage to person or property other than that

covered by the terms of this warranty.

• Any claims for lost revenue, lost profit or any similar costs

as a result of damage or repair.

• Attorney’s fees.

BERCOMAC’s responsibility in respect to claims is limited to

making the required repairs or replacement without charge up

to our maximum labor rates and pre-established times and no

claim of breach of warranty shall be cause for cancellation or

rescission of the contract of sale of any product or accessory.

This warranty gives you specific legal rights. You may also

have other rights, which vary from state to state.

NOTE: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify

any product previously manufactured.

Instructions for Obtaining Warranty Services:

Contact dealer where equipment was purchased or any other authorized service dealer to arrange service at their dealership. Requests

for warranty claims must be carried out through the same distribution network used to purchase the product. Don't forget to bring the

product and your proof of purchase (sales receipt) to the dealer.

TABLE OF CONTENTS

INTRODUCTION .................................................................................................................................................... 2

SAFETY PRECAUTIONS ...................................................................................................................................... 3

SAFETY DECALS .................................................................................................................................................. 5

ASSEMBLY

Tools Required ............................................................................................................................ 6

Step 1: Snowblower Preparation ............................................................................................................ 6

Step 2: Engine Installation ....................................................................................................................... 8

Step 3: Subframe Preparation .................................................................................................................. 11

Step 4: Vehicle Preparation ..................................................................................................................... 13

Step 5: Control Box Installation ............................................................................................................... 14

Step 6: Final Adjustments ........................................................................................................................ 17

OPERATION

Operating the Snowblower ....................................................................................................................... 19

Electrical Controls ..................................................................................................................................... 19

Removing Snow ........................................................................................................................................ 19

Clearing a Clogged Discharge Chute ...................................................................................................... 19

MAINTENANCE & DISMOUNTING

Maintenance .............................................................................................................................................. 20

Adjustments .............................................................................................................................................. 20

Lubrication ................................................................................................................................................. 20

Cutting Edge Maintenance ....................................................................................................................... 20

Auger and Fan Shear Bolt Replacement ................................................................................................. 20

Dismounting .............................................................................................................................................. 20

Storage ...................................................................................................................................................... 20

BELT REPLACEMENT .......................................................................................................................................... 21

TROUBLESHOOTING ........................................................................................................................................... 22

TORQUE SPECIFICATION TABLE ...................................................................................................................... 23

PARTS BREAKDOWN AND PARTS LIST

Rotation System with Chute ..................................................................................................................... 24

Subframe ................................................................................................................................................... 26

Snowblower ............................................................................................................................................... 28

OPTIONS & ACCESSORIES …….......................................................................................................................... 32

PAGE

INTRODUCTION

TO THE PURCHASER

This new accessory was carefully designed to give years of dependable service. This manual has been provided to

assist in the safe operation and servicing of your attachment.

NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but

are intended for reference only and are based on the latest product information available at the time of publication.

Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to

use. Carefully read, understand and follow these recommendations and insist that they be followed by those who will

use this attachment.

THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS

MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.

DANGER, WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF

HAZARD. HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions

are not followed.

WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are

not followed.

CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are

not followed.

Record your attachment serial number and purchase date in the section reserved below (there is no serial number on

the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement

parts. Use only genuine parts when replacements are required.

If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer

for warranty service.

This manual should be kept for future reference.

Please check if you have received all the parts for your kit with the list of the

bag and the list of the box.

SERIAL NUMBER : ___________________________

(IF APPLICABLE)

MODEL NUMBER: ___________________________

PURCHASE DATE : ___________________________

SAFETY PRECAUTIONS

Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle

and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury. All operators, no matter how experienced they may be,

should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal

obligation to instruct all operators in safe operation of the accessory.

GLOSSARY:

In this manual, right and left sides are determined by

sitting on the seat of the vehicle facing forward.

In this manual, "accessories" means attachments

(snowblower, rotary broom, blade etc.) that you install

on the vehicle (lawn tractors, A.T.V. s etc).

TRAINING:

This symbol, "Safety Alert Symbol", is used

throughout this manual and on the

accessory’s safety labels to warn of the

possibility of serious injury. Please take

special care in reading and understanding

the safety precautions before operating the

vehicle and accessory.

1. Read this owner's manual carefully. Be thoroughly

familiar with the controls and proper use of the

vehicle and accessory. Know how to stop the unit

and disengage the controls quickly.

2. Never allow children to operate the vehicle nor the

accessory. Never allow adults to operate the vehicle

nor the accessory without proper instructions.

3. No one should operate the vehicle nor the

accessory while intoxicated or while taking

medication that impairs the senses or reactions.

4. Keep the area of operation clear of all people,

particularly small children and pets.

PREPARATION:

1. Thoroughly inspect the area where the accessory

is to be used and remove door mats, all foreign

objects and the like.

2. For motorized accessories, disengage all clutches

and shift into neutral before starting engine.

3. Do not operate the accessory without wearing

adequate winter outer garments. Avoid loose fitting

clothing that can get caught in moving parts. Wear

footwear that will improve footing on slippery

surfaces.

4. Handle fuel with care, it is highly flammable.

a) Use approved fuel container.

b) Never add fuel to a running engine or hot engine.

c) Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

d) Never fill containers inside a vehicle, or on a

truck or a trailer bed with a plastic liner. Always

place containers on the ground, away from your

vehicle, before filling.

e) When practical, remove gas-powered

equipment from the truck or trailer and refuel it

on the ground. If this is not possible, then refuel

such equipment on a trailer with a portable

container, rather than from a gasoline

dispenser nozzle.

f) Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times, until

refueling is complete. Do not use a nozzle lock-

open device.

g) Replace fuel cap securely and wipe up spilled

fuel.

h) If fuel is spilled on clothing, change clothing

immediately.

5. Never attempt to make any adjustments while the

engine (motor) is running (except when specifically

recommended by manufacturer).

6. Let the vehicle and accessory adjust to outdoor

temperatures before starting to clear snow.

7. Never use an accessory without proper guards,

plates, or other safety protective devices in place

8. Always make sure to wear the appropriate safety

equipment required (glasses, muffs, mask…) for

each type of product. See operation section.

9. Always make sure of having safe traction on the

vehicle by using the recommended accessories

(chains, A.T.V. tracks, counterweights…). See

operation section.

10. Never modify the accessory or any part without

the written consent from the manufacturer.

OPERATION:

1. Do not put hands or feet near, under or inside rotating

parts.

2. Exercise extreme caution when operating on or

crossing gravel drives, walks or roads. Stay alert for

hidden hazards or traffic. Do not carry passengers.

3. After striking a foreign object, stop the engine (motor),

disconnect the wire from the spark plug(s) and keep

wire away to prevent accidental starting. Thoroughly

inspect the accessory for any damage and repair

damage before restarting and using the accessory.

4. If the unit should start to vibrate abnormally, stop the

engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

5. Take all possible precautions when leaving the

vehicle unattended. Disengage the power take-off,

lower the attachment, place the transmission into

neutral, set the parking brake, stop the engine and

remove the contact key.

6. Do not run the engine indoors, except when starting

the engine and for transporting in or out of the

building. Do not operate or let motor run in a storage

area without ventilation because gas contains

carbon monoxide which is odorless, colorless and

can cause death.

7. Never clean across the face of slopes, go from top

to bottom. Exercise extreme caution when using

equipment on slopes. Do not attempt to clear a

steep slope.

8. Never tolerate bystanders in the working zone.

Never use an accessory in the direction of

bystanders, it might throw gravel or debris that can

hurt people or damage property.

9. Never operate the accessory at high transport

speeds on slippery surfaces. Use care when

backing up.

10. Do not carry passengers.

11. Disengage power to the accessory when it is

transported or not in use.

12. Never operate the accessory without good visibility

or light.

14. Keep the accessory away from heat sources or

flames.

MAINTENANCE AND STORAGE

1. When cleaning, repairing or inspecting the vehicle

and accessory, make certain that all moving parts

have stopped. Disconnect wire from the spark

plug(s) and keep wire away to prevent accidental

starting.

2. Check all the bolts and components at frequent

intervals to make sure that they are properly

tightened.

3. Never store a motorized accessory with fuel in the

fuel tank inside a building where ignition sources are

present such as hot water and space heaters,

clothes dryers, and the like. Allow the engine to cool

before storing in any enclosure.

4. Always refer to the owner’s manual when you store

the accessory and vehicle for a prolonged or an

unspecified length of time.

5. Maintain or replace safety and instruction labels, as

necessary.

6 For winter accessories, (if applicable), let the engine

run for a few minutes after clean snow in order to

prevent the rotary parts from freezing.

7. Inspect the vehicle’s and accessory’s air filter every

day. Clean it or replace it as necessary. Change the

oil more often when working in dusty conditions.

See the vehicle’s and accessory's owner’s manual.

THIS SYMBOL MEANS

DANGER !

BECOME ALERT !

YOUR SAFETY IS INVOLVED !

SAFETY PRECAUTIONS

REPLACE IF DECALS ARE DAMAGED

SEE PARTS BREAKDOWN FOR DECAL LOCATION

SAFETY DECALS

Decal # 102125 Decal # 102126

Decal # 102127 Decal # 102553

Decal # 102128

Decal # 103951

ASSEMBLY

IMPORTANT: TORQUE ALL BOLTS ACCORDING

TO TORQUE SPECIFICATION TABLE (SEE TABLE

OF CONTENTS) WHEN STATED: TIGHTEN

FIRMLY. REFER TO PARTS BREAKDOWN

SECTION FOR PART IDENTIFICATION.

STEP 1

SNOWBLOWER PREPARATION:

Overall view of snowblower

TOOLS REQUIRED:

1 Ratchet

3 Sockets 7/16’’, 1/2’’, 9/16’’

3 Wrenches, 7/16’’, 1/2’’, 9/16’’

1 Hexagonal wrench 5/32’’

1 Wrench (for the nuts on the vehicle’s battery posts)

ASSEMBLY

Install two carriage bolts 1/4" x 1" (item 1) inside the

base of the chute. Install the support (item 2) and the

motor assembly (item 3) on the bolts.

Tighten into place with two flange nuts.

NOTE: Make sure the pin (item 4) on the electric

motor is well inserted in the hole on the support.

Install the motor assembly

Install the rotation ring (item 1) over opening (item 2)

as shown and align the notches.

Place the chute (item 3) (facing the rear) and clip the

back over the rotation ring then turn the chute

towards the front to lock into place.

Install chute

ASSEMBLY

STEP 2

ENGINE INSTALLATION:

IMPORTANT: THE RIGHT INSTALLATION OF THE ENGINE IS CRUCIAL TO THE GOOD

WORKING ORDER OF THE SNOWBLOWER.

NOTE: Figures 1 and 2 show an engine that is not well positioned.

IMPORTANT: We recommend using a 13 to 23 hp. engine with a 1’’ horizontal shaft on this snowblower

HERE ARE A FEW SUGGESTION OF ENGINES THAT HAVE BEEN TESTED.

Side view

Figure 2 Engine not in right position

Top view

Figure 1 Engine not in right position

AXIS AXIS

AXIS

Tested engines

Honda engines Kohler engine

HP 18 hp 20 hp 20 hp

Shaft 1" 1" 1"

Model GX610U QZE6 GX620K QXA6 PA64714

Muffler VHLM3 VHLM3 KH.24 786 06

Gas tank Not included Not included Not included

Pulley MB-31 (#104833) M-31 (#104833) MB-31 (#104833)

NOTE: The gas tank kit (option #700462 is recommended when it is not included with the engine.

ASSEMBLY

Remove the belt guard (item 3) by removing the three

1/4"x 1/2" hex. bolts (item 4).

IMPORTANT: The center of the shaft (item 1) must

be 4 7/8" and 2 1/8" from the frame of the snowblower

(see dimensions on the figure).

Place the engine on the stand (item 5). Use two 1"

shims (item 2) if required, to attain the height of 2 1/8"

as shown.

If more or less height is needed, use a couple of flat

washers.

Choose the set of holes on the stand that correspond

with those on the engine and to the position of the

engine shaft .

Secure with four hex. bolts 3/8" x 1 3/4" or 3/8" x 2

3/4", flat washers (on the slots if applicable) and

flange nuts.

NOTE: Make sure that the stand for the engine (item

4) is parallel with the snowblower frame.

Tighten the bolts firmly.

Install engine

For engines with an electric starter, it is necessary to

connect the vehicle's battery to the starter on the

snowblower engine. You must obtain option 700476

to allow this connection.

MOTOR INSTALLATION

DANGER:

It is the reponsibility of the person who installs

the engine and the controls to make sure that the

engaging system works well and that the

snowblower disengages effectivly at all times. It is

imperative to make the necessary adjustments if

applicable.

ASSEMBLY

Install the belt

Install the belts on the snowblower pulleys as shown.

NOTE: The adjustment with the tension on the belts

will be done in Step 6.

Choose the right pulley (#104833 = 1" or #104839 = 1

1/8") (item 1) according to the diameter of the

engine’s shaft.

Install the pulley (Fig. 1, item 1) on the engine shaft

as shown (hub towards the engine) with a 1/4" x 1/4"

x 1 3/4" key.

After positioning the engine, it is very important that

the pulleys are aligned and the axis must be parallel

as shown in the two views: (fig. 1) top view of the

snowblower and (fig. 2) the side view of the

snowblower.

(Use some shims if necessary).

Tip: Use a ruler (item 4) on the pulleys

Tighten the set screw firmly.

AXIS AXIS AXIS

Figure 1

Top view of

snowblower

AXIS

Figure 2

Side view of

snowblower

ASSEMBLY

STEP 3

SUBFRAME PREPARATION:

Determine according to the height of the vehicle

which set of holes to use to assemble the wheel

support (item 1) to the subframe (item 2).

The subframe must be parallel with the ground when

the subframe is installed under the vehicle.

Install the wheel support (item 1) to the subframe

(item 2) by using four 3/8" x 1" hex. bolts (item 3), four

flange nuts.

Tighten the bolts firmly.

Install the wheel support to the subframe

Install the assembled turnbuckles

Install the snowblower hitch (item 1) to the wheel

support (item 2) with the pin (item 3). Make sure the

pin is in the locked position.

Secure with the 4mm hair pin (item 4).

Tighten firmly.

Install the assembled turnbuckles (item 1) on the

subframe (item 2).

Secure with two 5/16" x 1" hex bolts (item 3), two

3/8" flat washers and nylon insert lock nuts.

Tighten loosely enough to allow the parts to move

freely.

Install snowblower hitch

ASSEMBLY

Adjust the length of the subframe

You have seven different positions on the adjustment

tube (item 1) (the adjustment tube can be inverted) to

adjust the length of the subframe.

To choose the right adjustment, insert the

adjustement tube (item 1) into the subframe (item 2)

and insert the hitch support (item 3) on the

adjustment tube. Do not secure.

Turn the hitch support to the side to facilitate

installation.

Drive the vehicle over the subframe, make sure the

caster wheels do not touch the front wheels on the

vehicle.

Identify the right length and secure in place with a pin

(item 4) and 3mm hair pin (item 5).

Choose between the three positions (see figure), the

height of the hitch support.

There must be a maximum of ground clearance

according to your vehicle.

Assemble the hitch support (items 1 & 2) with four

3/8" x 3/4" hex. bolts (item 3) and flange nuts (two on

each side). Position A does not have the hitch

supports (item 1).

Install the hitch (item 4) with a 3/8" x 3" hex bolt (item

5) and nylon insert lock nut.

Assemble the hitch support

Secure the hitch support on the tow hitch ball

Insert the assembled hitch support (item 1) onto

the adjustment tube (item 2). Secure in place with

the pin (item 3) and the 3mm hair pin (item 4).

NOTE: The hitch support has two sets of holes to

increase the length of the subframe if necessary.

Attach the hitch assembly on the tow hitch ball of

the vehicle.

IMPORTANT: Make sure the hitch is well adjusted

on the tow hitch ball.

Insert the pin (item 5) and secure with a 3 mm hair

pin (item 6). Make sure the subframe does not

come into contact with vehicle at any time.

NOTE: You can turn the hitch assembly (item1) to

facilitate displacing the vehicle over the subframe

by removing the pin (item 3).

ASSEMBLY

Install the winch cable

Insert the hook of the winch (item 1) into the flat bar

welded on the top of the snowblower.

NOTE: Optional kit #700269 Lift connection kit

reduces the effort and the speed required by the

winch to lift the accessory.

STEP 4

VEHICLE PREPARATION:

NOTE: A 1 7/8” or 50 mm tow hitch ball is required.

A) Install the lift strap (item 1) by looping it around the

suspension arm (as shown) on the vehicle.

Tighten the loop firmly.

# Item Description Action

B) Install the brackets (item 3) on both sides of

vehicle.

Bolt and nut from

suspension arm Remove.

2-3 Flat washer and

bracket Install and lightly

secure with the

original bolt and nut.

C) Install the brackets (item 4) on both sides of

vehicle.

Nut from

suspension arm Remove.

4 Bracket Install and lightly

secure with the

original nut.

Choose among the three different options to prepare

your vehicle (A, B, C).

Install the lift strap or the brackets.

Install the turnbuckles (item 1) into the brackets or

into the lift straps.

# Item Description Action

1 Turnbuckle

(qty 2) Adjust them so that the

subframe is centered

under the vehicle.*

*Tighten the turnbuckles firmly in order to tighten the

vehicle's suspension.

IMPORTANT: After adjusting the turnbuckles, tighten

the nuts on the vehicle’s suspension arms firmly.

Make sure to lock the nuts with the original locks. Hook the turnbuckles

ASSEMBLY

Install the control box

Connect the wires to the battery

STEP 5

CONTROL BOX INSTALLATION:

Install the control box and wires to the motors.

Three possible positions

Choose between the three different ways of securing

the control box support (item 1).

Use two hex bolts 1/4” x 1/2’’ or 1 1/2” (items 6 or 2),

support brackets (item 4), spacers (item 3) and flange

nuts.

Insert the control box (item 5) in the support.

Connect the three connectors at the end of the control

box wire to the three corresponding electric motors:

short wire on the motor for the chute (A), medium wire

on the motor for the deflector (B), long wire on the

motor for the belt tensioner (C) and the circuit breaker

wire (D).

There will be one black connector that will not be

connected. This is to connect the optional

snowblower light (E).

Make sure the connectors are well connected

together.

NOTE: If the switches don’t match the right

controls, reconnect the connectors with the right

motors.

ASSEMBLY

IMPORTANT: The control box is equipped with a

red emergency switch. Push down on this button if it

becomes necessary to stop the engine quickly.

ENGINE CIRCUIT BREAKER (D)

INSTALLATION: (EMERGENCY SWITCH

WIRE):

Find the wire (item 1) on the engine that supplies

the engine’s booster coil and disconnect it.

Assemble the connector (item 2) on the control box

wire to the connector (item 3) on the engine wire

(item 1).

Assemble the connector (item 5) on control box wire

to the connector (item 4) on the engine wire (item

1).

NOTE: The emergency switch must be pulled out to

start the engine of the snowblower.

Connect the red wire to the vehicle's positive battery

post (item 1) and the black wire to the negative

battery post (item 2).

Tie the wires to the vehicle with the nylon tie wraps

so the do not get in the way.

NOTE: These wires will stay attached to the vehicle.

Install engine circuit breaker

Identify the controls.

ASSEMBLY

IMPORTANT:

Take the time to familiarize yourself with the location

of the switches and with their use.

NOTE: If the switches don’t match the right

controls, reconnect the connectors with the right

motors.

Pay particular attention to the switch for the belt

tensioner (item 4).This switch must be held in position

for a few seconds in order to activate or deactivate

the lever of the belt tensioner.

Make sure that the action is complete when you

engage or disengage the snowblower.

DANGER:

It is the reponsibility of the person who installs

the engine and the controls to make sure that the

engaging system works well and that the

snowblower disengages effectivly at all times. It is

imperative to make the necessary adjustments if

applicable.

Identification of the switches:

1. Emergency switch. (Pull out to start)

2. Switch for the chute

3. Switch for the deflector

4. Switch for the belt tensioner.

Secure wires on the motors

Turn the chute to its maximum towards the right.

Secure the wire of the motor for the deflector with a

couple of tie wraps (item 1 & 2) as shown.

Secure the other wires with a few tie wraps (items 3, 4 &

5) as shown.

Be sure to leave enough wire length to be able to turn

the chute freely.

OPERATION

Figure 1

Top view of snowblower. All the pulleys are aligned

and the engine is well installed.

AXIS AXIS AXIS

ASSEMBLY

Adjust the idler pulley (item 2) as follows:

After installing the belt, you may run the engine

without the belt guard, but only for the time needed to

verify the belt alignment. Do not leave the

snowblower without supervision.

Neither you or anyone must approach the moving

parts.

Observe and familiarize yourself with the action time

required to engage and disengage the snowblower.

Then make sure that the belt is well aligned,

especially on the idler pulley.

If necessary, you can add or remove a flat washer for

final adjustment on the idler pulley (item 2).

Install belt guard

STEP 6

FINAL ADJUSTMENTS

DANGER

Never let the snowblower motor run without the

belt guard in place.

WARNING

TO PREVENT INJURIES:

Start the engine, engage and disengage the

clutch to be sure if functions normally.

Make sure the emergency switch is working

perfectly. Make sure all the controls are working

well.

Make sure the belt guide (item 2) is installed in the

appropriate hole on the belt guard (item 3)

according to the diameter of the engine shaft used.

The hole on the right hand is for the 1" shaft and the

hole on left hand is for the 1 1/8" shaft (sitting on the

vehicle).

Insert a flange nut 5/16’’ (item 1) on the hex bolt

5/16’’ x 2 3/4’’ (item 2) as shown. Install the

assembled bolt in the belt guard and secure with the

other flange nut 5/16’’ (item 4).

IMPORTANT: make sure the belt does not rub on

the belt guide when the belt is engaged.

MAINTENANCE

ASSEMBLY

Adjust skid shoes

VERIFY SKID SHOE ADJUSTMENT:

LEVEL PAVED SURFACE: Adjust skid shoes to allow

3/16" to 1/4" clearance (A) between cutting edge and

surface.

UNEVEN OR GRAVEL SURFACE: Adjust skid shoes

to allow 1/2" to 5/8" clearance (A) between cutting

edge and surface.

Install the belt guard (item 1) and secure in place with

three hex bolts 1/4" x 1/2" (item 2).

Install belt guard

DANGER:

It is the reponsibility of the person who installs

the engine and the controls to make sure that the

engaging system works well and that the

snowblower disengages effectivly at all times. It is

imperative to make the necessary adjustments if

applicable.

If necessary: Move the engine in the slots to

reduce the tension on the belt when it is

disengaged.

La page charge ...

Bercomac 700480-1 Manuel utilisateur

Marque: Bercomac

Modèle: 700480-1

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Bercomac 700480-1 User manual

Documents connexes

Autres documents

Berco 700529-1 Le manuel du propriétaire