Bercomac 700210-1 700211-1 Manuel utilisateur

Marque: Bercomac

Modèle: 700210-1 700211-1

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

Berco

Deluxe Two Stage 40" & 44" Snowblower

for

LAWN, YARD & GARDEN TRACTORS

CAUTION:

READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE

OPERATING YOUR EQUIPMENT

103331_EN J-05

* ASSEMBLY * REPAIR PARTS

* OPERATION * MAINTENANCE

*103331_EN*

OWNER’S MANUAL

Model Number

700210-1

700211-1

LIMITED WARRANTY

Bercomac Limitée

92, Fortin North, Adstock, Quebec, Canada, G0N 1S0

Conditions and Products Covered:

BERCOMAC guarantees any part of the product or accessory

manufactured by BERCOMAC and found in the reasonable

judgment of BERCOMAC to be defective in material and or

workmanship will be repaired or replaced by an authorized

dealer without charge up to our maximum labor rates and pre-

established times. For replacement parts only standard ground

freight services are covered. This warranty extends to the

original retail purchaser only and is not transferable to any

subsequent purchasers.

Warranty Period

(from date of the original retail purchase)

xResidential use: 1 year

xSemi-commercial, professional or rental use: 90 days

Exceptions Noted Below; the following items are guaranteed

by the original manufacturer and have their own warranty,

conditions and limited time:

xTire Chains: 90 days

xEngines (installed in factory on BERCO equipment): 2 years

xEngines (sold separately): Validate with the dealer.

Please refer to the engine manufacturer’s warranty

statement included with the unit. BERCOMAC is not

authorized to handle warranty adjustments on engines.

Items and Conditions NOT Covered:

This warranty does not cover the following:

xPick-up or delivery charges or in-home services fees.

xAny damage or deterioration of the unit, parts and or finish

of these due to normal use, wear and tear, or exposure.

xCost of regular use or maintenance service or parts, such as

gas, oil, lubricants, tune-up parts, and adjustments.

xAny part or accessory which has been altered, modified,

misused, neglected, accidentally damaged or not properly

installed, maintained, stored or repaired not in accordance

with the instructions in the owner’s manual.

xRepair due to normal wear and or any wear items such as

shear pins, bolts, belts, etc.

xExpedited freight fee services for replacement parts.

xShear bolts and shear pins are to be considered as a

preventive measure not as an assured protection, any

damages resulting from the lack of shear bolts breakage are

not covered.

NOTE: All warranty work must be performed by an authorized

dealer using original (manufacturer) replacement parts.

Owner’s Responsibilities:

BERCOMAC’s defective equipment or part must be returned

to an authorized dealer within the warranty period for repairs.

In the event that defective merchandise must be returned to

manufacturer for repairs, freight fees are prepaid and a written

authorization from BERCOMAC must be obtained by dealer

prior to the shipment. This warranty extends only to

equipment operated under normal conditions. To validate a

warranty claim, it is the user’s responsibility to maintain and

service the unit as specified in the owner’s manual or to have

the unit serviced at their dealer at their expense.

General Conditions:

The sole liability of BERCOMAC with respect to this warranty

shall be strictly and exclusively repair and replacement as

mentioned herein. BERCOMAC shall not have any liability for

any other costs, loss or damage, including but not limited to,

any incidental or consequential loss or damage.

In particular, without being limited to, BERCOMAC shall have

no liability or responsibility for:

xTravel time, overtime, after hours time or other

extraordinary repair charges or relating to repairs and or

replacements outside of normal business hours.

xRental of like or similar replacement equipment during the

period of any, repair or replacement work.

xAny communicating or travel charges.

xLoss or damage to person or property other than that

covered by the terms of this warranty.

xAny claims for lost revenue, lost profit or any similar costs

as a result of damage or repair.

xAttorney’s fees.

BERCOMAC’s responsibility in respect to claims is limited to

making the required repairs or replacement without charge up

to our maximum labor rates and pre-established times and no

claim of breach of warranty shall be cause for cancellation or

rescission of the contract of sale of any product or accessory.

This warranty gives you specific legal rights. You may also

have other rights, which vary from state to state.

NOTE: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify

any product previously manufactured.

Instructions for Obtaining Warranty Services:

Contact dealer where equipment was purchased or any other BERCOMAC service dealer to arrange service at their dealership. To

locate a dealer convenient to you, access our website at www.bercomac.com. Don't forget to bring the product and your proof of

purchase (sales receipt) to the BERCOMAC dealer.

TABLE OF CONTENTS

INTRODUCTION ................................................................................................................................................... 2

SAFETY PRECAUTIONS ..................................................................................................................................... 3

SAFETY DECALS ................................................................................................................................................. 5

ASSEMBLY

Step 1: Snowblower Preparation ............................................................................................................ 6

Step 2: Snowblower Installation ............................................................................................................. 10

OPERATION

Operating the Snowblower ...................................................................................................................... 11

Controls .................................................................................................................................................... 11

Removing Snow ....................................................................................................................................... 11

MAINTENANCE

Maintenance ............................................................................................................................................. 12

Adjustments .............................................................................................................................................. 12

Lubrication ................................................................................................................................................ 12

Clearing a Discharge Chute .................................................................................................................... 12

Cutting Edge Replacement ..................................................................................................................... 12

Shear Bolt Replacement .......................................................................................................................... 12

Belt Replacement ..................................................................................................................................... 12

End of Season Storage ........................................................................................................................... 12

DISMOUNTING

Snowblower Dismounting ........................................................................................................................ 13

Subframe Dismounting ............................................................................................................................ 13

TROUBLESHOOTING .......................................................................................................................................... 14

PARTS BREAKDOWN AND LISTS

Rotation System with Chute .................................................................................................................... 16

Snowblower .............................................................................................................................................. 18

TORQUE SPECIFICATION TABLE ..................................................................................................................... 21

OPTIONS & ATTACHMENTS ............................................................................................................................... 22

PAGE

INTRODUCTION

TO THE PURCHASER

This new accessory was carefully designed to give years of dependable service. This manual has been provided to

assist in the safe operation and servicing of your attachment.

NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but

are intended for reference only and are based on the latest product information available at the time of publication.

Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to

use. Carefully read, understand and follow these recommendations and insist that they be followed by those who will

use this attachment.

THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS

MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.

DANGER, WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF

HAZARD. HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions

are not followed.

WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are

not followed.

CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are

not followed.

Record your attachment serial number and purchase date in the section reserved below (there is no serial number on

the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement

parts. Use only genuine parts when replacements are required.

If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer

for warranty service.

This manual should be kept for future reference.

Please check if you have received all the parts for your kit with the list of the

bag and the list of the box.

SERIAL NUMBER : ___________________________

(IF APPLICABLE)

MODEL NUMBER: ___________________________

PURCHASE DATE : ___________________________

SAFETY PRECAUTIONS

Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle

and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury. All operators, no matter how experienced they may be,

should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal

obligation to instruct all operators in safe operation of the accessory.

GLOSSARY:

In this manual, right and left sides are determined by

sitting on the seat of the vehicle facing forward.

In this manual, "accessories" means attachments

(snowblower, rotary broom, blade etc.) that you install

on the vehicle (lawn tractors, A.T.V. s etc).

TRAINING:

This symbol, "Safety Alert Symbol", is used

throughout this manual and on the

accessory’s safety labels to warn of the

possibility of serious injury. Please take

special care in reading and understanding

the safety precautions before operating the

vehicle and accessory.

1. Read this owner's manual carefully. Be thoroughly

familiar with the controls and proper use of the

vehicle and accessory. Know how to stop the unit

and disengage the controls quickly.

2. Never allow children to operate the vehicle nor the

accessory. Never allow adults to operate the vehicle

nor the accessory without proper instructions.

3. No one should operate the vehicle nor the

accessory while intoxicated or while taking

medication that impairs the senses or reactions.

4. Keep the area of operation clear of all people,

particularly small children and pets.

PREPARATION:

1. Thoroughly inspect the area where the accessory

is to be used and remove door mats, all foreign

objects and the like.

2. For motorized accessories, disengage all clutches

and shift into neutral before starting engine.

3. Do not operate the accessory without wearing

adequate winter outer garments. Avoid loose fitting

clothing that can get caught in moving parts. Wear

footwear that will improve footing on slippery

surfaces.

4. Handle fuel with care, it is highly flammable.

a) Use approved fuel container.

b) Never add fuel to a running engine or hot engine.

c) Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

d) Never fill containers inside a vehicle, or on a

truck or a trailer bed with a plastic liner. Always

place containers on the ground, away from your

vehicle, before filling.

e) When practical, remove gas-powered

equipment from the truck or trailer and refuel it

on the ground. If this is not possible, then refuel

such equipment on a trailer with a portable

container, rather than from a gasoline

dispenser nozzle.

f) Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times, until

refueling is complete. Do not use a nozzle lock-

open device.

g) Replace fuel cap securely and wipe up spilled

fuel.

h) If fuel is spilled on clothing, change clothing

immediately.

5. Never attempt to make any adjustments while the

engine (motor) is running (except when specifically

recommended by manufacturer).

6. Let the vehicle and accessory adjust to outdoor

temperatures before starting to clear snow.

7. Never use an accessory without proper guards,

plates, or other safety protective devices in place

8. Always make sure to wear the appropriate safety

equipment required (glasses, muffs, mask…) for

each type of product. See operation section.

9. Always make sure of having safe traction on the

vehicle by using the recommended accessories

(chains, A.T.V. tracks, counterweights…). See

operation section.

10. Never modify the accessory or any part without

the written consent from the manufacturer.

OPERATION:

1. Do not put hands or feet near, under or inside rotating

parts.

2. Exercise extreme caution when operating on or

crossing gravel drives, walks or roads. Stay alert for

hidden hazards or traffic. Do not carry passengers.

3. After striking a foreign object, stop the engine (motor),

disconnect the wire from the spark plug(s) and keep

wire away to prevent accidental starting. Thoroughly

inspect the accessory for any damage and repair

damage before restarting and using the accessory.

4. If the unit should start to vibrate abnormally, stop the

engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

5. Take all possible precautions when leaving the

vehicle unattended. Disengage the power take-off,

lower the attachment, place the transmission into

neutral, set the parking brake, stop the engine and

remove the contact key.

6. Do not run the engine indoors, except when starting

the engine and for transporting in or out of the

building. Do not operate or let motor run in a storage

area without ventilation because gas contains

carbon monoxide which is odorless, colorless and

can cause death.

7. Never clean across the face of slopes, go from top

to bottom. Exercise extreme caution when using

equipment on slopes. Do not attempt to clear a

steep slope.

8. Never tolerate bystanders in the working zone.

Never use an accessory in the direction of

bystanders, it might throw gravel or debris that can

hurt people or damage property.

9. Never operate the accessory at high transport

speeds on slippery surfaces. Use care when

backing up.

10. Do not carry passengers.

11. Disengage power to the accessory when it is

transported or not in use.

12. Never operate the accessory without good visibility

or light.

13. Keep the accessory away from heat sources or

flames.

MAINTENANCE AND STORAGE

1. When cleaning, repairing or inspecting the vehicle

and accessory, make certain that all moving parts

have stopped. Disconnect wire from the spark

plug(s) and keep wire away to prevent accidental

starting.

2. Check all the bolts and components at frequent

intervals to make sure that they are properly

tightened.

3. Never store a motorized accessory with fuel in the

fuel tank inside a building where ignition sources are

present such as hot water and space heaters,

clothes dryers, and the like. Allow the engine to cool

before storing in any enclosure.

4. Always refer to the owner’s manual when you store

the accessory and vehicle for a prolonged or an

unspecified length of time.

5. Maintain or replace safety and instruction labels, as

necessary.

6 For winter accessories, (if applicable), let the engine

run for a few minutes after clean snow in order to

prevent the rotary parts from freezing.

7. Inspect the vehicle’s and accessory’s air filter every

day. Clean it or replace it as necessary. Change the

oil more often when working in dusty conditions.

See the vehicle’s and accessory's owner’s manual.

THIS SYMBOL MEANS

DANGER !

BECOME ALERT !

YOUR SAFETY IS INVOLVED !

SAFETY PRECAUTIONS

SAFETY DECALS

REPLACE IF DECALS ARE DAMAGED

SEE PARTS BREAKDOWN FOR DECAL LOCATION

Decal #102126

Decal #102127

Decal #102125

Decal #102128

Decal #102124

Decal #102129

Place snowblower face down.

IMPORTANT:

Tractors with a vertical engine and with the drive

pulley underneath:

No modifications are needed (go to next page).

Tractors with a horizontal engine and with the drive

pulley in front:

Remove the belt guard (item 1).

Remove the set screws (item 2) and pulley (item 3).

If the screws are difficult to unscrew, slightly heat the

hub with a blowtorch around the screws.

Turn the pulley, the hub (item 4) towards the bolts (item

5) and slide it back on the shaft.

Align the holes and apply three drops of "lock tite" in

each hole.

Tighten the set screws firmly.

Reinstall the belt guard (item 1).

Note: If the pulley is difficult to remove, unscrew the

four bolts (item 5) and remove the shaft assembly.

IMPORTANT: TORQUE ALL BOLTS ACCORDING

TO TORQUE SPECIFICATION TABLE (SEE TABLE

OF CONTENTS) WHEN STATED: TIGHTEN

FIRMLY. REFER TO PARTS BREAKDOWN FOR

THEIR IDENTIFICATION.

Pulley before modification

ASSEMBLY

Pulley after modification

Remove belt guard

Place snowblower face down

STEP 1

SNOWBLOWER PREPARATION:

CAUTION

Never use the snowblower without the belt guard.

Install the male hitch (item 1) as shown with three

7/16 x 1 1/4" bolts (item 2), lock washers, nylon insert

locknuts and a 7/16 x 1 1/4" bolt (item 3) with a

flatwasher over the slot, lockwasher and a nylon

insert locknut as shown.

Tighten the bolts firmly.

Turn the snowblower upright.

Place the rotation ring (item 1) on top of the

snowblower (item 2) as shown.

Only one position provides a perfect fit.

ASSEMBLY

Install male hitch

Install rotation ring

ASSEMBLY

Grease both ends of the rotation worm (item 1).

Insert the short rotation bushing (item 2) and the

long rotation bushing (item 3) on the rotation worm

as shown.

Insert the rotation worm with the short bushing in the

sleeve (item 1).

Insert the worm support (item 2) on the long bushing

as shown.

Apply grease on the rotation ring (item 1).

Install the chute (item 2) with the four retaining

plates (item 3) as shown.

At the rear left hand corner, secure a retaining plate

(item 3) on top and the rotation worm support (item

5) underneath with two 1/4 x 3/4" bolts (item 4) and

flange nuts as shown.

Secure the other three retaining plates (item 3) with

six 1/4 x 1/2" bolts (item 6) and flange nuts.

Tighten the bolts firmly.

Install rotation worm

Install chute

Insert bushings on rotation worm

ASSEMBLY

Install the hand guard (item 1) as shown.

Secure in place with two 1/4 x 3/4" bolts (item 2), the

flat washers and flange nuts inside.

Tighten the bolts firmly.

Install the handgrip (item 1) as shown.

Insert the hook (item 2) in the handle and secure with

a 2.5 mm hair pin (item 3).

Note: Store these parts until snowblower installation.

Install handgrip and hook

Install hand guard

ASSEMBLY

VERIFY SKID SHOE ADJUSTMENT:

LEVEL PAVED SURFACE: Adjust skid shoes to allow

3/16" to 1/4" clearance (A) between cutting edge and

surface.

UNEVEN OR GRAVEL SURFACE: Adjust skid shoes

to allow 1/2" to 5/8" clearance (A) between cutting

edge and surface.

VERIFY TIRE PRESSURE:

Snowblower should raise 3" to 4" above ground, (no

more, no less) if not, check and adjust tractor tire

pressure.

See subframe owner’s manual for proper tire

pressure.

Tire pressure must be even on both sides of tractor.

Adjust skid shoes

STEP 2

SNOWBLOWER INSTALLATION:

See the subframe’s owner’s manual for snowblower

installation instructions.

WARNING

FOR YOUR SECURITY:

Read the subframe owner's manual for safety

precautions and rules.

Follow the assembly and operation instructions.

OPERATING THE SNOWBLOWER

a) Make sure the snowblower is clear of snow

before engaging the snowblower.

b) Make sure that the auger and fan operate freely.

c) Start the tractor engine.

d) Before engaging the snowblower drive, always

have the engine running at medium R.P.M.

e) Operate the snowblower at maximum engine

R.P.M.

IMPORTANT: USE FULL ENGINE R.P.M. WHEN

REMOVING WET, STICKY SNOW. LOW R.P.M.

WILL TEND TO PLUG THE CHUTE.

CONTROLS

CHUTE ROTATION

The chute rotation handle is located to the left of

steering wheel. Turning the handle in a clockwise

direction, the discharge chute will turn in a clockwise

direction or vice versa.

CHUTE DEFLECTOR

Set the angle of the deflector according to the distance

the snow must be thrown and to prevent property

damage. To change the deflector angle, loosen the two

deflector knobs & adjust the deflector to the appropriate

angle and retighten the two knobs securely.

REMOVING SNOW

When removing snow, do not use the snowblower as

a dozer blade to push snow. Allow snowblower to

ingest snow at its own speed. If the speed of your

tractor is too fast, the snowblower may become

overloaded and plug. For best results, raise the

snowblower and remove a top layer of snow. A

second pass with the snowblower will remove the

remaining snow.

OPERATION

WARNING

-Do not attempt to clear plugged chute, auger or

fan of snow while tractor engine is running.

-Disengage snowblower.

-Lower snowblower onto ground.

-Set the parking brake.

-Stop engine, remove the ignition key, disconnect

the wire from spark plug(s) and keep away from

spark plug(s) to prevent accidental starting.

-Make sure all moving parts have stopped.

-Do not use hand to unplug chute.

-Use a 36’’ (924 mm.) minimum length stick or

board.

WARNING

Read the tractor Owner’s Manual carefully. Be

thoroughly familiar with the controls & proper

use of the attachment. Know how to stop the

attachment & disengage the controls quickly.

WARNING

TO PREVENT INJURIES AND FOR MORE

TRACTION WHEN USING AN ATTACHMENT:

-Rear counterweights of 100 lbs. minimum are

required to counter-balance attachment’s

weight.

-Tractor manufacturer approved tire chains are

required.

-Do not operate on slopes greater than 10°.

-When dismounting an attachment remove rear

counterweights.

MAINTENANCE

a) Check mounting bolts at frequent intervals for proper

tightness in order to prevent costly repairs. Make

sure your attachment is in safe working condition.

b) Provide adequate blocking before working under the

attachment when in raised position.

ADJUSTMENTS

SKID SHOE ADJUSTMENT:

Level Paved Surface: Adjust skid shoes to allow 3/16" to

1/4" clearance between cutting edge and surface.

Uneven or Gravel Surface: Adjust skid shoes to allow

1/2" to 5/8" clearance between cutting edge and

surface.

LUBRICATION

Apply oil at all pivot points.

Drive Chains: Lubricate with chain saw chain lubricant

every four hours of operation and at the end of each

operation.

Chute Rotation System: Oil chute base, rotation worm

every eight hours of operation.

CUTTING EDGE MAINTENANCE

Verify from time to time the wearing on the cutting

edge to make sure you do not wear out the base of

the snowblower’s chassis. This cutting edge is

reversible. All you have to do is unscrew the bolts and

turn the cutting edge, reinstall and tighten the bolts

securely.

SHEAR BOLT REPLACEMENT

*The shear bolts are to be considered a preventive

and not an assured protection. Operator vigilance is

required. Thoroughly inspect the areas where the

snowblower is to be used and remove all foreign

objects.

Fan Shear Bolt Replacement:

The fan is protected by a special shear bolt with one

groove. If you hit a foreign object or ice, the shear bolt is

designed to break upon absorbing impact. The fan will

stop turning. This is to avoid damage to the fan or the

snowblower. Replace only with original part (for

identification, see parts list: "Snowblower Head").

Accessible by removing belt guard. Hole designed for

inserting screwdriver is located on the side of housing.

The head of the bolt must be on the right side. The use

of any other bolt may void the warranty.

Auger Shear Bolt Replacement:

The auger is protected by a special shear bolt with two

grooves. If you hit a foreign object or ice, the shear bolt

is designed to break upon absorbing impact. The auger

will stop turning. This is to avoid damage to the auger or

the snowblower. Replace only with original parts (for

identification, see parts list: "Snowblower Head").

Accessible by removing the belt guard. The use of any

other bolt may void the warranty.

BELT REPLACEMENT

NOTE: See subframe owner's manual for V-belt

installation and adjustment.

END OF SEASON STORAGE

a) Clean snowblower and subframe thoroughly and

repaint all parts from which paint has worn.

b) List the replacement parts that will be needed for the

next season.

c) Store the snowblower and the subframe in a dry

place.

MAINTENANCE

WARNING

TO PREVENT INJURIES:

Stop the motor.

Apply parking brake.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent accidental

starting.

CLEARING A CLOGGED DISCHARGE

CHUTE:

Hand contact with the rotating impeller inside the

discharge chute is the most common cause of injury

associated with snowblowers. Never use your hand to

clean out the discharge chute.

To clear the chute:

1. Lower snowblower to the ground and set parking

brake.

2. SHUT THE ENGINE OFF & REMOVE KEY!

3. Wait 10 seconds to be sure the all moving parts

such as the impeller blades have stopped moving.

4. Disconnect wire from the spark plug(s) and keep

wire away to prevent accidental starting.

5. Always use a clean-out tool of at least 36” in length,

NOT YOUR HANDS.

DISMOUNTING

SNOWBLOWER DISMOUNTING:

a) Select a level surface, set parking brake, stop

engine, remove the ignition key and remove spark

plug wire from engine spark plug (s). Keep wire

away from plug (s) to prevent accidental starting.

b) Remove the hair pin from the rotation handle and

remove handle.

c) Tractors with Manual P.T.O. Clutch:

Disengage the clutch lever, loosen or remove the

tractor belt guide, remove the belt from tractor drive

pulley and subframe idlers.

d) Tractors with Electric P.T.O. Clutch:

Release the tension on the belt by moving the

tension arm forward. Remove the belt from tractor

drive pulley and subframe idlers.

e) Detach the snowblower by lifting the spring locks on

quick hitch and pulling back the snowblower one

side at a time .

SUBFRAME DISMOUNTING

NOTE: See Subframe owner's manual for dismounting

instructions.

TROUBLESHOOTING

* Please refer to parts breakdown section for parts identification.

PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION

Snowblower is noisy.

Note: Please note this

snowblower may appear to be

loud.

New chain and new sprocket. Lubricate the roller chains.

Note: When snowblower is new it is

louder, the noise will decrease over

time.

Snowblower vibrates or is

abnormally noisy. Damaged pulley. Replace pulley.

Damaged bearing. Replace bearing.

Damaged fan. Dismount & repair or replace fan.

Auger bent. Replace auger.

Auger stopped turning. Shear bolt broken. Replace shear bolt. Also see

"Maintenance" section.

Chain broken or connecting link

unlocked. Remove chain guard. Inspect and

repair if needed.

Fan stopped turning. Shear bolt broken or sheared. Replace bolt. The head of the bolt

must be on the right side.

Snowblower stopped turning. Drive belt is damaged or snapped. Check & replace damaged belt. See

Belt Replacement instructions in

"Maintenance" section.

Snowblower was engaged when

already plugged. Make sure auger & fan are not

plugged or frozen before engaging

snowblower.

Belt is worn at a specific point. Lack of tension on the belt. Adjust the manual clutch cable or

replace the springs which are

stretched & have lost their strength.

See belt adjustment section in the

subframe owner’s manual.

Belt showing premature wear. Belt guides misaligned. Make sure guides do not touch belt at

any point, at any time.

Snowblower pulley displaced. Check pulley on the snowblower to

see if it is not displaced. Make sure

pulley on the snowblower, the flat

idler and the V pulley on drive

mechanism are well aligned.

Spring stretched. Check spring. Replace if stretched.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION

Chute rotation is difficult. Dirt or ice may be underneath chute. Clean the base of chute & the rotation

ring. Lubricate chute inside & out and

the rotation worm. Clean parts,

lubricate & reinstall. Make sure the

retaining plates are not too tight on

the chute base, it may be a reason

why the chute is not turning freely.

The base of the chute may be

damaged or bent. Dismount the chute by removing the

retaining plates. Verify that the base

of the chute is very even and not bent

in a corner, if it is, straighten.

The chute plugs easily. Tractor engine R.P.M. is too slow. Always have tractor engine at full

R.P.M. when using the snowblower.

Advancing too quickly with

snowblower. Reduce speed. Allow snowblower to

ingest snow at its own speed.

Snowblower digs into ground. Ground is not frozen or too soft. Adjust skid shoes lower so they may

better support the snowblower. If

problem persists, change skid shoes

for "Heavy Duty Skid Shoes" (option

model #700243) which cover more

surface and prevents snowblower

from digging.

Snowblower does not raise

evenly. Rear tire pressure uneven from one

side to another. Verify and adjust tire pressure:

Front tires: 14 to 15 p.s.i.

Rear tires: 7 to 8 p.s.i.

Maladjustment of the snowblower. Loosen male hitch on snowblower.

Place a shim (ex.: piece of wood

approx. 2” thick) under the lower side

of snowblower which needs to be

levelled. Re-tighten bolts.

Snowblower does not raise

enough or raises too much. Lift mechanism is not well adjusted. Adjust the adjustment rod on the push

arm to obtain a 3" to 3 1/2" lift height.

Auger turns the wrong way. Belt is installed improperly. See belt mounting instructions in

specific attachment (snowblower or

broom), installation section in

subframe manual.

PARTS BREAKDOWN

CHUTE WITH ROTATION SYSTEM

Ref.

Réf. English description Description française Qty.

Qté. Part #

Pièce #

1Chute Goulotte 1102058

2Knob Bouton 2102020

3Nylon flat washer 11/32" Rondelle plate de nylon 11/32" 2102009

4Nylon flat washer 7/16" Rondelle plate de nylon 7/16" 2102011

5Carriage bolt 5/16" n.c. x 3/4" Boulon à carrosserie 5/16" n.c. x 3/4" 2O/L

6Hand guard Fourche protectrice 1102012

7Flat washer 5/16" hole Rondelle plate 5/16" trou 2O/L

8Flange nut 1/4" n.c. Écrou à bride 1/4" n.c. 10 O/L

9Retaining plate Plaque de retenue 4102007

10 Hex. bolt 1/4" n.c. x 1/2" Boulon hex. 1/4" n.c. x 1/2" 6O/L

11 Hex. bolt 1/4" n.c. x 3/4" Boulon hex. 1/4" n.c. x 3/4" 4O/L

12 Worm support Support de spirale 1102014

13 Rotation ring Anneau de rotation 1102016

14 Rotation bushing Coussinet de rotation 1102060

15 Rotation worm Spirale de rotation 1102005

16 Rotation bushing Coussinet de rotation 1102059

17 Handle Manivelle 1102061

18 Handgrip Poignée 1102062

19 Handle hook Crochet de manivelle 1102006

20 Hair pin 2.5mm Goupille à ressort 2.5mm 1102013

PARTS LIST

CHUTE WITH ROTATION SYSTEM

21 Warning decal Décalque attention 1102125

22 Danger decal Décalque danger 1102127

23 Frame Châssis 1REF

O/L = Obtain Locally

PARTS BREAKDOWN

SNOWBLOWER HEAD

La page charge ...

Bercomac 700210-1 700211-1 Manuel utilisateur

Marque: Bercomac

Modèle: 700210-1 700211-1

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Bercomac 700210-1 700211-1 User manual

Bercomac 700210-1 700211-1 Manuel utilisateur

Bercomac 700210-1 700211-1 Manuel utilisateur

dans d''autres langues

Documents connexes