Bercomac 700533-1 Manuel utilisateur

Marque: Bercomac

Modèle: 700533-1

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

BERCO

66’’ Nordic Snowblower

For

ZERO TURN MOWERS

CAUTION:

READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE

OPERATING YOUR EQUIPMENT

105944_EN K-12

* ASSEMBLY * REPAIR PARTS

* OPERATION * MAINTENANCE

*105944_en*

OWNER’S MANUAL

Model Number

700533-1 66’’ Snowblower

LIMITED WARRANTY

Bercomac Limitée

92, Fortin North, Adstock, Quebec, Canada, G0N 1S0

Conditions and Products Covered:

BERCOMAC guarantees any part of the product or accessory

manufactured by BERCOMAC and found in the reasonable

judgment of BERCOMAC to be defective in material and or

workmanship will be repaired or replaced by an authorized

dealer without charge up to our maximum labor rates and pre-

established times. For replacement parts only standard ground

freight services are covered. This warranty extends to the

original retail purchaser only and is not transferable to any

subsequent purchasers.

Warranty Period

(from date of the original retail purchase)

xResidential or semi-commercial use: 1 year

xCommercial, professional or rental use: 90 days

Exceptions Noted Below; the following items are guaranteed

by the original manufacturer and have their own warranty,

conditions and limited time:

xTire Chains: 90 days

xEngines: Will vary as per the manufacturer

Please refer to the engine manufacturer’s warranty

statement included with the unit. BERCOMAC is not

authorized to handle warranty adjustments on engines.

Items and Conditions NOT Covered:

This warranty does not cover the following:

xPick-up or delivery charges or in-home services fees.

xAny damage or deterioration of the unit, parts and or finish

of these due to normal use, wear and tear, or exposure.

xCost of regular use or maintenance service or parts, such as

gas, oil, lubricants, tune-up parts, and adjustments.

xAny part or accessory which has been altered, modified,

misused, neglected, accidentally damaged or not properly

installed, maintained, stored or repaired not in accordance

with the instructions in the owner’s manual.

xRepair due to normal wear and or any wear items such as

shear pins, bolts, belts, etc.

xExpedited freight fee services for replacement parts.

xShear bolts and shear pins are to be considered as a

preventive measure not as an assured protection, any

damages resulting from the lack of shear bolts breakage are

not covered.

NOTE: All warranty work must be performed by an authorized

dealer using original (manufacturer) replacement parts.

Owner’s Responsibilities:

BERCOMAC’s defective equipment or part must be returned

to an authorized dealer within the warranty period for repairs.

In the event that defective merchandise must be returned to

manufacturer for repairs, freight fees are prepaid and a written

authorization from BERCOMAC must be obtained by dealer

prior to the shipment. This warranty extends only to

equipment operated under normal conditions. To validate a

warranty claim, it is the user’s responsibility to maintain and

service the unit as specified in the owner’s manual or to have

the unit serviced at their dealer at their expense.

General Conditions:

The sole liability of BERCOMAC with respect to this warranty

shall be strictly and exclusively repair and replacement as

mentioned herein. BERCOMAC shall not have any liability for

any other costs, loss or damage, including but not limited to,

any incidental or consequential loss or damage.

In particular, without being limited to, BERCOMAC shall have

no liability or responsibility for:

xTravel time, overtime, after hours time or other

extraordinary repair charges or relating to repairs and or

replacements outside of normal business hours.

xRental of like or similar replacement equipment during the

period of any, repair or replacement work.

xAny communicating or travel charges.

xLoss or damage to person or property other than that

covered by the terms of this warranty.

xAny claims for lost revenue, lost profit or any similar costs

as a result of damage or repair.

xAttorney’s fees.

BERCOMAC’s responsibility in respect to claims is limited to

making the required repairs or replacement without charge up

to our maximum labor rates and pre-established times and no

claim of breach of warranty shall be cause for cancellation or

rescission of the contract of sale of any product or accessory.

This warranty gives you specific legal rights. You may also

have other rights, which vary from state to state.

NOTE: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify

any product previously manufactured.

Instructions for Obtaining Warranty Services:

Contact dealer where equipment was purchased or any other BERCO service dealer to arrange service at their dealership. To locate a

dealer convenient to you, access our website at www.bercomac.com. Don't forget to bring your proof of purchase (sales receipt) to the

BERCO dealer.

TABLE OF CONTENTS

INTRODUCTION .................................................................................................................................................... 2

SAFETY PRECAUTIONS ...................................................................................................................................... 3

SAFETY DECALS .................................................................................................................................................. 5

ASSEMBLY

Tools Required .......................................................................................................................................... 6

Step 1: Snowblower Preparation ............................................................................................................... 6

Step 2: Snowblower Installation ................................................................................................................ 8

Step 3: Control Box Installation ................................................................................................................. 9

Step 4: Skid Shoe Adjustment and Installation of the Spring ................................................................. 11

OPERATION

Operating the Snowblower ........................................................................................................................ 12

Electrical Controls ...................................................................................................................................... 12

Removing Snow ........................................................................................................................................ 12

Clearing a Clogged Chute ........................................................................................................................ 12

MAINTENANCE

Adjustments ............................................................................................................................................... 13

Lubrication ................................................................................................................................................. 13

Cutting Edge Maintenance......................................................................................................................... 13

Clearing a Clogged Discharge Chute ...................................................................................................... 13

Augers and Fan Shear Bolt Replacement ............................................................................................... 13

Belt installation, Adjustment and Replacement ...................................................................................... 14

DISMOUNTING & STORAGE ............................................................................................................................... 15

TROUBLESHOOTING ........................................................................................................................................... 16

TORQUE SPECIFICATION TABLE ...................................................................................................................... 19

PARTS BREAKDOWN AND PARTS LIST

66’’ Snowblower ........................................................................................................................................ 20

OPTIONS & ATTACHMENTS ................................................................................................................................ 25

PAGE

INTRODUCTION

TO THE PURCHASER

This new accessory was carefully designed to give years of dependable service. This manual has been provided to

assist in the safe operation and servicing of your attachment.

NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but

are intended for reference only and are based on the latest product information available at the time of publication.

Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to

use. Carefully read, understand and follow these recommendations and insist that they be followed by those who will

use this attachment.

THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS

MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.

DANGER, WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF

HAZARD. HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions

are not followed.

WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are

not followed.

CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are

not followed.

Record your attachment serial number and purchase date in the section reserved below (there is no serial number on

the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement

parts. Use only genuine parts when replacements are required.

If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer

for warranty service.

This manual should be kept for future reference.

Please check if you have received all the parts for your kit with the list of the

bag and the list of the box.

SERIAL NUMBER : ___________________________

(IF APPLICABLE)

MODEL NUMBER: ___________________________

PURCHASE DATE : ___________________________

SAFETY PRECAUTIONS

Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle

and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury. All operators, no matter how experienced they may be,

should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal

obligation to instruct all operators in safe operation of the accessory.

GLOSSARY:

In this manual, right and left sides are determined by

sitting on the seat of the vehicle facing forward.

In this manual, "accessories" means attachments

(snowblower, rotary broom, blade etc.) that you install

on the vehicle (lawn tractors, A.T.V. s etc).

TRAINING:

This symbol, "Safety Alert Symbol", is used

throughout this manual and on the

accessory’s safety labels to warn of the

possibility of serious injury. Please take

special care in reading and understanding

the safety precautions before operating the

vehicle and accessory.

1. Read this owner's manual carefully. Be thoroughly

familiar with the controls and proper use of the

vehicle and accessory. Know how to stop the unit

and disengage the controls quickly.

2. Never allow children to operate the vehicle nor the

accessory. Never allow adults to operate the vehicle

nor the accessory without proper instructions.

3. No one should operate the vehicle nor the

accessory while intoxicated or while taking

medication that impairs the senses or reactions.

4. Keep the area of operation clear of all people,

particularly small children and pets.

PREPARATION:

1. Thoroughly inspect the area where the accessory

is to be used and remove door mats, all foreign

objects and the like.

2. For motorized accessories, disengage all clutches

and shift into neutral before starting engine.

3. Do not operate the accessory without wearing

adequate winter outer garments. Avoid loose fitting

clothing that can get caught in moving parts. Wear

footwear that will improve footing on slippery

surfaces.

4. Handle fuel with care, it is highly flammable.

a) Use approved fuel container.

b) Never add fuel to a running engine or hot engine.

c) Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

d) Never fill containers inside a vehicle, or on a

truck or a trailer bed with a plastic liner. Always

place containers on the ground, away from your

vehicle, before filling.

e) When practical, remove gas-powered

equipment from the truck or trailer and refuel it

on the ground. If this is not possible, then refuel

such equipment on a trailer with a portable

container, rather than from a gasoline

dispenser nozzle.

f) Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times, until

refueling is complete. Do not use a nozzle lock-

open device.

g) Replace fuel cap securely and wipe up spilled

fuel.

h) If fuel is spilled on clothing, change clothing

immediately.

5. Never attempt to make any adjustments while the

engine (motor) is running (except when specifically

recommended by manufacturer).

6. Let the vehicle and accessory adjust to outdoor

temperatures before using.

7. Never use an accessory without proper guards,

plates, or other safety protective devices in place

8. Always make sure to wear the appropriate safety

equipment required (glasses, muffs, mask…) for

each type of product. See operation section.

9. Always make sure of having safe traction on the

vehicle by using the recommended accessories

(chains, A.T.V. tracks, counterweights…). See

operation section.

10. Always make sure the all components are correctly

installed. (driveline securely attached and locked at

both ends, belts properly installed…)

11. Never modif

the accessor

or an

part without

the written consent from the manufacturer.

OPERATION:

1. Do not put hands or feet near, under or inside rotating

parts.

2. Exercise extreme caution when operating on or

crossing gravel drives, walks or roads. Stay alert for

hidden hazards or traffic. Do not carry passengers.

3. After striking a foreign object, stop the engine (motor),

disconnect the wire from the spark plug(s) and keep

wire away to prevent accidental starting. Thoroughly

inspect the accessory for any damage and repair

damage before restarting and using the accessory.

4. If the unit should start to vibrate abnormally, stop the

engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

5. Take all possible precautions when leaving the

vehicle unattended. Disengage the power take-off,

lower the attachment, place the transmission into

neutral, set the parking brake, stop the engine and

remove the contact key.

6. Do not run the engine indoors, except when starting

the engine and for transporting in or out of the

building. Do not operate or let motor run in a storage

area without ventilation because gas contains

carbon monoxide which is odorless, colorless and

can cause death.

7. Never use the accessories across the face of

slopes, go from top to bottom. Exercise extreme

caution when using equipment on slopes. Do not

attempt to clear a steep slope.

8. Never tolerate bystanders in the working zone.

Never use an accessory in the direction of

bystanders, it might throw gravel or debris that can

hurt people or damage property.

9. Never operate the accessory at high transport

speeds on slippery surfaces. Use care when

backing up.

10. Do not carry passengers.

11. Disengage power to the accessory when it is

transported or not in use.

12. Never operate the accessory without good visibility

or light.

13. Keep the accessory away from heat sources or

flames.

MAINTENANCE AND STORAGE

1. When cleaning, repairing or inspecting the vehicle

and accessory, make certain that all moving parts

have stopped. For gasoline engine, disconnect wire

from the spark plug(s) and keep wire away to

prevent accidental starting.

2. Check all the bolts and components at frequent

intervals to make sure that they are properly

tightened.

3. Never store a motorized accessory with fuel in the

fuel tank inside a building where ignition sources are

present such as hot water and space heaters,

clothes dryers, and the like. Allow the engine to cool

before storing in any enclosure.

4. Always refer to the owner’s manual when you store

the accessory and vehicle for a prolonged or an

unspecified length of time.

5. Maintain or replace safety and instruction labels, as

necessary.

6 For winter accessories, (if applicable), let the engine

run for a few minutes after clean snow in order to

prevent the rotary parts from freezing.

7. Inspect the vehicle’s and accessory’s air filter (if

applicable) every day. Clean it or replace it as

necessary. Change the oil more often when working

in dusty conditions. See the vehicle’s and

accessory's owner’s manual.

THIS SYMBOL MEANS

DANGER !

BECOME ALERT !

YOUR SAFETY IS INVOLVED !

SAFETY PRECAUTIONS

SAFETY DECALS

REPLACE IF DECALS ARE DAMAGED

SEE PARTS BREAKDOWN FOR DECAL LOCATION

To avoid serious injury:

Keep hands, feet & clothing away from rotating auger

while engine is running.

To avoid serious injury:

Keep hands out of this discharge chute while engine

is running.

To avoid injury from drive belt:

Keep hands, feet & clothing away.

Do not attempt to install or remove drive belt without

reading owner’s manual.

DECAL #105126

DECAL #105128

DECAL #105127

DECAL #105130

Before installing or using:

Locate, read and make sure to understand all of the

owner’s manual.

DECAL #105131

Refer to owner’s manual about wearing safety

glasses, ear muffs and mask.

Refer to owner’s manual for use of counter weights,

cat tracks and tire chains.

1-Do not drive faster than 3 KM/H when the

snowblower is in operation.

2-Do not drive faster than 10 KM/H when the

snowblower is in the raised position.

3-The head of the snowblower weighs 155kg.

4-The engine wattage is 17.2kW. (according to the

engine of the vehicle).

5-The sound pressure level (107dBA) is measured

at the engine (full charge at 3600 RPM) and

depends on the engine that is installed. The value

indicated is a reference only.

ASSEMBLY

IMPORTANT: TORQUE ALL BOLTS ACCORDING

TO TORQUE SPECIFICATION TABLE (SEE TABLE

OF CONTENTS) WHEN STATED: TIGHTEN

FIRMLY. REFER TO PARTS BREAKDOWN

SECTION FOR PART IDENTIFICATION.

TOOLS REQUIRED:

Wrench: 7/16’’

Socket: 7/16’’

Screwdriver No.2

Pliers

Allen Key 1/8’’ Overall view of snowblower

STEP 1

SNOWBLOWER PREPARATION:

Refer to parts breakdown section for parts

identification.

Install the nylon rotation ring (item 1).

# Item Description Action

1 Rotation ring

(nylon)

Install over the opening

as shown and align the

notches.

Install the nylon rotation ring

Install the rotation ring (item 1).

# Item Description Action

1 Rotation ring Install over the opening

as shown.

NOTE: Place the rotation ring (item 1) approximately

as shown in the drawing, the groves of the rotation

ring on the teeth of the rotation motor.

ASSEMBLY

Install the chute (item 1).

# Item Description Action

1 Chute Place the chute on

the nylon rotation

ring. Turn the chute

to make sure it turns

freely. Place the

chute at 45° angle

as shown.

2 Hex bolt

1/4’’ n.c x 1’’

(qty 4)

Insert under the

rotation ring (item 5)

as shown.

3 Spacers

(qty 4)

Install on the bolts

between the rotation

ring and the chute.

4 Nylon insert lock

nuts 1/4’’

(qty 4)

Secure everything in

place.

Install the chute

Install the retaining plate (item 2) under the chute .

# Item Description Action

1 Hex. bolt

1/4"n.c. x 1/2"

(qty 2)

Insert as shown.

2 Retaining plate Install as shown

under the chute

3 Nylon insert lock nut

1/4" thin

(qty 2)

Secure in place.

Install the retaining plate

Attach the snowblower to the subframe as shown.

TIPS: Install a block under the snowblower. Align

and drive the vehicle forward up to the

snowblower to quick connect the snowblower to the

subframe.

Make sure the snowblower is pushed in until locked

into place by the lock (item 1).

INSTALLATION

STEP 2

SNOWBLOWER INSTALLATION:

You must install the subframe and drive mechanism

before continuing to install the snowblower.

WARNING

TO PREVENT INJURIES:

Stop the motor.

Apply parking brake.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent accidental

starting.

NOTE: See the belt installation instructions in the

Maintenance section.

Insert the snowblower in the lock.

WARNING

The belt tension arm & needs to be held firmly while

displacing to prevent injury.

WARNING

Never use the snowblower without the belt guard.

Familiarize yourself with the winch control and make

sure the cable stays wrapped from the bottom of the

drum of the winch. See picture of the winch in the

subframe’s owner manual.

Lift and lower the snowblower using the switch.

When lowering the accessory, release the switch of

the winch control as soon as the accessory touches

the ground.

Install the pulley block

After installing the belt, hook the pulley block (item 1)

in the bracket as shown.

# Item Description Action

1 Pulley block Hook into the bracket as

shown.

NOTE: To thread the winch cable, you must remove

the pulley from the pulley block.

2 End of the cable Install over the hole on

the subframe as shown.

3 Flat washer 3/8’’ Install over the end of

the cable.

4 Bolt 5/16’’ x 1’’ Install in the flat washer

and secure with a nylon

insert locknut.

ASSEMBLY

STEP 3

CONTROL BOX INSTALLATION:

NOTE: Install the control box in this place only if the

threads on the control panel are made of metal.

Remove the two existing screws from the place

where the control box will be installed. (Can be

installed on the side of the control panel according to

the model of the tractor).

# Item Description Action

1 Support plate Install as shown.

2 Machine screw

#10 x 32 x 1/2’’

(qté 2)

Insert as shown.

3 Box support Install as shown.

4 Hex bolt

1/4’’ x 1/2’’

(qty 2)

Insert in the holes as

shown.

5 Flange nuts

(qty 2)

Tighten the bolts in

place.

6 Control box Install on the box

support.

Install the control box

Thread the wires on the frame to the front where they

will not be seen and where they won’t touch any hot or

moving parts.

Attach to the vehicle’s frame using the tie wraps.

NOTE: It is recommended to place the wire connectors

as close as possible to the subframe. Secure the wires

in an adequate place in order to separate the accessory

from the vehicle when storing.

Connect the wires to the electric motors. The longest

wires are connected to the deflector motor.

Connect the red wire to the positive battery post and

the black wire to the negative battery post.

ASSEMBLY

Turn the chute to its maximum towards the right.

Secure the wire with another nylon tie wrap in the hole

(item 1) at the base of the deflector as shown.

Secure the wire for the rotation motor (item 2) with a tie

wrap.

Be sure to leave enough wire length to be able to turn

the chute freely.

Identify the controls

IMPORTANT:

Take the time to familiarize yourself with the joystick

(item A) on the control box.

Joystick identification:

1. Deflector: up and down

2. Chute: left to right

ASSEMBLY

STEP 4

SKID SHOE ADJUSTMENT:

LEVEL PAVED SURFACE: Adjust skid shoes to allow

3/16" to 1/4" or 5mm to 7mm clearance (A) between

cutting edge and surface.

UNEVEN OR GRAVEL SURFACE: Adjust skid shoes

to allow 1/2" to 5/8" or 13mm to 16mm clearance (A)

between cutting edge and surface.

NOTE: Lift the snowblower as high as it will go to

install the spring.

# Item Description Action

1 Spring Insert on end in the

hole on the subframe.

2 Shackle Insert in the other end

of the spring (item 1)

and then secure in the

hole of the snowblower.

Reinstall the belt guard.

NOTE: Remove the belt guard before installing the

spring.

INSTALLATION OF THE SPRING

Install spring

Adjust skid shoes as shown

OPERATING THE SNOWBLOWER

a) Make sure the snowblower is clear of snow

before engaging the clutch.

b) Make sure that the auger and impeller operate

freely.

c) Start the snowblower engine.

d) Before engaging the snowblower drive, always

have the engine running at max R.P.M.

e) Operate the snowblower at maximum engine

R.P.M.

IMPORTANT: USE FULL ENGINE R.P.M. WHEN

REMOVING WET, STICKY SNOW. LOW R.P.M.

POWER WILL TEND TO PLUG THE CHUTE.

ELECTRICAL CONTROLS

See installation of the control box in order to identify the

controls.

RAISING AND LOWERING THE SNOWBLOWER:

Press on the switch of the winch control to lift or lower

the accessory to the ground.

There is a stopper that limits the lifting.

When lowering the accessory, release the switch of

the winch control as soon as the accessory touches

the ground.

OPERATION

REMOVING SNOW

When removing snow, do not use the snowblower as

a dozer blade to push snow. Allow snowblower to

ingest snow at its own speed. If the speed of your

vehicle is too fast, the snowblower may become

overloaded and plug.

WARNING

Read the vehicle's owner’s manual carefully. Be

thoroughly familiar with the controls & proper

use of the attachment. Know how to stop the unit

& disengage the controls quickly.

WARNING

-Do not attempt to clear plugged chute, auger or

fan of snow while the snowblower's engine is

running.

-Disengage snowblower.

-Lower snowblower onto ground.

-Set the parking brake.

-Stop engine, remove the ignition key, disconnect

the wire from spark plug(s) and keep away from

spark plug(s) to prevent accidental starting.

-Make sure all moving parts have stopped.

-Do not use hand to unplug chute.

-Use a 36’’ (1m) minimum length stick or board.

WARNING

TO PREVENT INJURIES AND FOR MORE

TRACTION WHEN USING SNOWBLOWER:

-Do not drive faster than 3 km/hr (2 m/hr) with

snowblower on the ground.

-Do not drive faster than 10 km/hr (6 m/hr) with

the snowblower in raised position.

-Do not operate on a slope greater than 10°.

-Vehicle manufacturer approved tire chains are

required.

-Counterweight kit sold separately.

-Familiarize yourself with driving the vehicle with

the snowblower in the raised position.

Hand contact with the rotating impeller inside the

discharge chute is the most common cause of injury

associated with snowblowers. Never use your hand to

clean out the discharge chute.

To clear the chute:

1. Lower snowblower to the ground and set parking

brake.

2. SHUT THE ENGINE OFF & REMOVE KEY!

3. Wait 10 seconds to be sure the all moving parts

such as the impeller blades have stopped moving.

4. Disconnect wire from the spark plug(s) and keep

wire away to prevent accidental starting.

5. Always use a clean-out tool of at least 36” in length,

NEVER YOUR HANDS.

CLEARING A CLOGGED DISCHARGE

CHUTE:

MAINTENANCE

Refer to parts breakdown section for parts

identification.

WARNING

TO PREVENT INJURIES:

Stop the motor.

Apply parking brake.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent accidental

starting.

CAUTION

TO PREVENT INJURIES:

-Check mounting bolts at frequent intervals for

proper tightness in order to prevent costly repairs.

-Make sure your snowblower is in safe working

condition.

-Provide adequate blocking before working under

snowblower when in raised position.

AUGERS AND FAN SHEAR BOLT

REPLACEMENT

Shear bolts are to be considered a preventive

measure and not an assured protection. Operator

vigilance is required. Thoroughly inspect the areas

where the snowblower is to be used and remove all

foreign objects.

To avoid damage to the snowblower:

Use only the original shear bolts (grooved bolts).

#105627 (Item A) in bags of ten for the fan.

#105602 (item B) in bags of 10 for the augers.

The use of any other shear bolt will not insure any

protection and may void the warranty.

IMPORTANT: It is very important to replace the augers

in the same position as shown in the drawing before

installing the shear bolts.

MAINTENANCE

SKID SHOE ADJUSTMENT:

LEVEL PAVED SURFACE: Adjust skid shoes to allow

3/16" to 1/4" or 5mm to 7mm clearance (A) between

cutting edge and surface.

UNEVEN OR GRAVEL SURFACE: Adjust skid shoes

to allow 1/2" to 5/8" or 13mm to 16mm clearance (A)

between cutting edge and surface.

CUTTING EDGE MAINTENANCE

Verify from time to time the wearing on the cutting

edge to make sure you do not wear out the base of

the snowblower’s chassis. This cutting edge is

reversible.

SNOWBLOWER PULLEY REPLACEMENT

or ALIGNMENT:

Clean the parts before aligning or replacing the pulley.

Apply some "Loctite" 2760 on the key and the set

screws. Tighten firmly. (Use heat to soften the "loctite’’

when removing the set screws).

LUBRICATION

Grease the wheel axles, the fork pivots after every

sixteen hours of use.

Apply oil at all pivot points.

Chute Rotation System: Oil chute base, rotation worm

every sixteen hours of operation.

Gear box:

Check the oil annually. If necessary, add AGMA 5 EP or

SAE 90 oil.

The gear box should have a total of 155 ml of oil or filled

to the rim of the bolt hole when installed on the

snowblower. (see figure)

MAINTENANCE

BELT INSTALLATION, ADJUSTMENT,

AND REPLACEMENT:

WARNING

The belt tension arm is spring loaded & needs to be

held firmly while displacing to prevent injury.

SNOWBLOWER BELT:

a) Lower the snowblower to the ground.

b) Remove the belt guard.

c) Remove tension on the belt by lowering the tension

arm (item 1)

d) Loosen the knob (item 2) on the bracket that holds

the bearing (item 3).

e) Install the belt as shown.

f) Adjust the bracket by pushing on the bearing (item

3) to apply a slight pressure on the back of the belt

(just enough to hold the belt in place). It is normal

that the bearing is off centre (towards the vehicle)

on the pulley. Just make sure that it does not come

into contact with the wall of the pulley.

Top view

Position of the bearing

IMPORTANT:

When aligning or replacing the snowblower pulley,

you must clean the parts and use ‘’Lock-tite’’ 2760 on

the key and the set screws. Tighten firmly.

Position of the belts

Belt Insertion

Distance between coils

g) Tighten firmly with the knob.

h) Apply tension on the belt by pulling up the tension

arm (item 1).

i) Engage the snowblower for a few seconds under

supervision. Stop the engine. Inspect the belt to

make sure it does not interfere with any parts; that

it is well inserted in the pulleys and that it has not

flipped on it’s side while still on the pulleys. The V

of the belt must be in the V of the pulleys. The

back of the belt must rest on the flat pulleys (D)

as shown.

j) Reinstall the belt guard.

k) Use genuine belts only, they are specifically

fabricated for this application.

NOTE: There must be a good tension on the belt at

all times. If spring is damaged or stretched, you must

replace it.

DRIVE MECHANISM BELT:

See subframe manual for belt replacement

instructions.

CAUTION

Never use the snowblower without the belt guard.

STORAGE

a) Clean snowblower thoroughly and repaint all

parts from which paint has worn.

b) List the replacement parts that will be needed to

be replaced before the next season.

c) Follow the instructions in the Lubrication section.

d) Store the snowblower, subframe and drive

mechanism in a dry place.

WARNING

Never use the snowblower without the belt guard.

Never operate the vehicle with the counterweights

in place without the snowblower.

SNOWBLOWER DISMOUNTING

a) Remove the belt guard.

b) Remove the spring.

c) Unhook the pulley block from the snowblower.

d) Release the tension on the belt by displacing the

tension arm backwards. Remove the belt from the

drive mechanism pulley under the tractor.

e) Disconnect the electric connectors.

f) Remove the snowblower by activating the latch of

the female hitch and by backing up the vehicle.

g) Reinstall the belt guard.

CAUTION

The belt tension is spring loaded & needs to be

held firmly while displacing to prevent injury.

DISMOUNTING & STORAGE

* Please refer to parts breakdown section for parts identification.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION

One section or both sections of the

auger stops turning.

Shear bolts are probably broken. Replace shear bolts.

Fan stops turning. Shear bolt is probably broken. Replace shear bolts.

Snowblower stops turning. One of the two belts is probably

damaged or broken.

Check both belts and replace

damaged belt(s).

Belt snapping, shredding or burning Lack of tension on belt. Adjust the tension of the spring or

replace springs if stretched.

Snowblower engaged when

plugged.

Make sure the auger & the fan are

not frozen or plugged before

engaging.

Not original belts. Always use original belts.

Worn belt. Belt may be worn

causing a slack.

Inspect the belt. Replace if required.

Not original shear bolts. Use original shear bolts

Imperfections in pulleys. Verify if the pulleys are damaged.

Verify that pulleys are smooth,

without rust spots. Sand down the

pulleys or replace them.

Interference. Make sure that belt does not come

into contact with any other part,

bolts, guides etc... when engaged.

Belt has flipped on its side. When installing new belt, have

snowblower run between 20 to 40

seconds. Turn everything off and

verify that belt has not turned on its

side. If so, remove belt and re-install

in opposite fashion to rectify the bad

twist the belt has taken.

Chute plugs easily. Tractor engine turning too slowly. Run engine at full throttle during

snowblowing operation.

Advancing too quickly with tractor. Allow snowblower to ingest snow at

its own speed.

Chute rotation is difficult. Dirt or ice may be underneath

chute.

Dismount chute. Clean the base of

chute and the rotation ring.

Lubricate & re-install.

Snowblower digs into ground. Ground is not frozen or too soft. Adjust skid shoes lower so they

may better support the snowblower.

If problem persists, change skid

shoes for heavy duty skid shoes

(option #700243) which cover more

surface and prevents snowblower

from digging.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION

Snowblower does not raise evenly. Tire pressure uneven from one side

to another.

Verify and adjust tire pressure:

Front tires: 14 to 15 psi

Rear tires: 7 to 8 psi

Snowblower vibrates or is

abnormally noisy.

Damaged pulley. Replace pulley.

Damaged bearing. Replace bearing.

Damaged fan. Dismount & repair or replace fan.

Damaged auger. Replace auger.

* Please refer to parts breakdown section for parts identification.

PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION

Winch runs backwards. Winch wires reversed. Recheck wiring.

Switch wires reversed. Recheck wiring.

Switch installed incorrectly. Check switch installation.

Battery wires reversed. Recheck wiring.

Winch cable is not winded up from

the bottom of spool.

Wind winch cable from underneath.

Winch will not operate or runs in

one direction only.

Vehicle’s ignition switch is at OFF

position.

Turn vehicle’s ignition switch at ON

position.

Broken wires or bad connection. Check for poor connections.

Control switch is inoperative. Replace control switch.

Relay or breaker is damaged. Replace the relay or breaker.

Limit switch is damaged. Replace limit switch.

Winch is damaged. Replace or repair winch.

Winch runs but with insufficient

power or line speed.

Weak battery. Recharge or replace battery.

Check charging system.

Poor battery connection. Check battery terminals for

corrosion. Clean when required.

Winch is damaged. Replace or repair winch.

* Please refer to parts breakdown section in subframe manual for parts identification.

MAINTENANCE

* Please refer to parts breakdown section in subframe manual for parts identification.

TROUBLESHOOTING

HOW TO KNOW POINTS TO CHECK

Poor connections. Recheck wiring with the owner's manual.

HI/LOW voltage tester does not work. Connect it on battery posts (+ and -) of a functional battery.

If there is no light, the tester is damaged.

The control switch inoperative. Test both connectors with HI/LOW voltage tester.

If light comes ON in both positions (IN & OUT), the switch is

operative.

Relay is damaged When it is working, there is a "CLICK" sound when the control switch

is activated. Check connections with HI / LOW voltage tester.

Winch is damaged The ultimate test is to connect the winch directly to the battery and

reverse the wires to test both directions. If the winch doesn't work, it is

damaged.

The limit switch is damaged. When the limit switch is pushed or stuck inside, the winch can't raise

the accessory, only lower it. If not replace it.

The breaker is damaged. Check the voltage on both terminals on the breaker with the HI / LOW

voltage tester. If not replace.

La page charge ...

Bercomac 700533-1 Manuel utilisateur

Marque: Bercomac

Modèle: 700533-1

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Bercomac 700533-1 User manual

Documents connexes

Autres documents

Berco 700529-1 Le manuel du propriétaire