Bercomac 700374 700378 Manuel utilisateur

Marque: Bercomac

Modèle: 700374 700378

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

OWNER’S MANUAL

Model Number

700374

700378

Berco

Northeast Two Stage 44" & 48’’ Snowblower

for

LAWN, YARD & GARDEN TRACTORS

CAUTION:

READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE

OPERATING YOUR EQUIPMENT

103953 G-11

* ASSEMBLY * REPAIR PARTS

* OPERATION * MAINTENANCE

Conditions and Products Covered:

BERCOMAC guarantees any part of the product or accessory

manufactured by BERCOMAC and found in the reasonable

judgment of BERCOMAC to be defective in material and or

workmanship will be repaired or replaced by an authorized

dealer without charge up to our maximum labor rates and pre-

established times. For replacement parts only standard

ground freight services are covered. This warranty extends to

the original retail purchaser only and is not transferable to any

subsequent purchasers.

Warranty Period

(from date of the original retail purchase):

x Residential use: 1 year

x Commercial or rental use: 90 days

Exceptions Noted Below: the following items are guaranteed

by the original manufacturer and have their own warranty,

conditions and limited time.

x Tire Chains: 90 days

x Engines (supplied with BERCOMAC equipment): 2 years

Please refer to the engine manufacturer’s warranty

statement included with the unit. BERCOMAC is not

authorized to handle warranty adjustments on engines.

Items and Conditions NOT Covered:

This warranty does not cover the following:

x Pick-up or delivery charges or in-home services fees.

x Any damage or deterioration of the unit, parts and or finish

of these due to normal use, wear and tear, or exposure.

x Cost of regular use or maintenance service or parts, such

as gas, oil, lubricants, tune-up parts, and adjustments.

x Any part or accessory which has been altered, modified,

misused, neglected, accidentally damaged or not properly

installed, maintained, stored or repaired not in accordance

with the instructions in the owner’s manual.

x Repair due to normal wear and or any wear items such as

shear pins, bolts, belts, etc.

x Expedited freight fee services for replacement parts.

x Shear bolts and shear pins are to be considered as a

preventive measure not as an assured protection, any

damages resulting from the lack of shear bolts breakage

are not covered.

NOTE: All warranty work must be performed by an authorized

dealer using original (manufacturer) replacement parts.

Owner’s Responsibilities:

BERCOMAC’s defective equipment or part must be returned to

an authorized dealer within the warranty period for repairs. In

the event that defective merchandise must be returned to

manufacturer for repairs, freight fees are prepaid and a written

authorization from BERCOMAC must be obtained by dealer

prior to the shipment. This warranty extends only to

equipment operated under normal conditions. To validate a

warranty claim, it is the user’s responsibility to maintain and

service the unit as specified in the owner’s manual at their

expense.

General Conditions:

The sole liability of BERCOMAC with respect to this warranty

shall be strictly and exclusively repair and replacement as

mentioned herein. BERCOMAC shall not have any liability for

any other costs, loss or damage, including but not limited to,

any incidental or consequential loss or damage.

In particular, without being limited to, BERCOMAC shall have

no liability or responsibility for:

x Travel time, overtime, after hours time or other extraordinary

repair charges or relating to repairs and or replacements

outside of normal business hours.

x Rental of like or similar replacement equipment during the

period of any, repair or replacement work.

x Any communicating or travel charges.

x Loss or damage to person or property other than that

covered by the terms of this warranty.

x Any claims for lost revenue, lost profit or any similar costs

as a result of damage or repair.

x Attorney’s fees.

BERCOMAC’s responsibility in respect to claims is limited to

making the required repairs or replacement without charge up

to our maximum labor rates and pre-established times and no

claim of breach of warranty shall be cause for cancellation or

rescission of the contract of sale of any product or accessory.

This warranty gives you specific legal rights. You may also

have other rights, which vary from state to state.

Note: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify

any product previously manufactured.

Instructions for Obtaining Warranty Services:

Contact dealer where equipment was purchased or any other BERCOMAC Service Dealer to arrange service at their dealership. To

locate a dealer convenient to you, access our website at www.bercomac.com.

Bring the product and your proof of purchase (sales receipt) to the BERCOMAC dealer.

LIMITED WARRANTY

INTRODUCTION ...................................................................................................................................... 2

SAFETY PRECAUTIONS ......................................................................................................................... 3

SAFETY DECALS ..................................................................................................................................... 5

ASSEMBLY

Step 1: Snowblower Preparation ................................................................................................. 6

Step 2: Snowblower Installation ................................................................................................... 7

OPERATION

Snowblower Operation ................................................................................................................. 9

Controls ........................................................................................................................................ 9

Snow Removal ............................................................................................................................. 9

MAINTENANCE

Maintenance ................................................................................................................................ 10

Adjustments ................................................................................................................................. 10

Lubrication ................................................................................................................................... 10

Cutting Edge Maintenance ........................................................................................................... 10

Auger and Fan Shear Bolt Replacement ..................................................................................... 10

End of Season Storage ................................................................................................................ 10

Belt Installation, Adjustment and Replacement ........................................................................... 11

DISMOUNTING

Snowblower Dismounting ............................................................................................................ 12

TROUBLESHOOTING .............................................................................................................................. 13

TORQUE SPECIFICATION TABLE .......................................................................................................... 15

PARTS BREAKDOWN & LISTS

Chute with Rotation System ......................................................................................................... 16

Snowblower ................................................................................................................................. 18

OPTIONS & ATTACHMENTS ............................................................................................... 21

TABLE OF CONTENTS

Page

INTRODUCTION

TO THE PURCHASER

This new attachment was carefully designed to give years of dependable service. This manual has been provided to

assist in the safe operation and servicing of your attachment.

NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but

are intended for reference only and are based on the latest product information available at the time of publication.

Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to use.

Carefully read, understand and follow these recommendations and insist that they be followed by those who will use

this attachment.

THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS MANUAL

THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH. DANGER,

WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF HAZARD.

HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions are

not followed.

WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are not

followed.

CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are not

followed.

Record your attachment serial number and purchase date in the section reserved below. Your dealer requires this

information to give you prompt, efficient service when ordering replacement parts. Use only genuine parts when

replacements are required.

If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer

for warranty service.

This manual should be kept for future reference.

Please check if you have received all the parts for your kit with the list of the

bag and the list of the box.

SERIAL NUMBER : ___________________________

PURCHASE DATE : ___________________________

In this manual, right and left sides are determined by sitting on the tractor seat facing forward.

SAFETY PRECAUTIONS

Careful operation is your best insurance against an accident. Read this section carefully before operating the tractor

and snowblower. This snowblower is capable of amputating hands and feet and throwing objects. Failure to observe

the following safety instructions could result in serious injury. All operators, no matter how experienced they may be,

should read this and other manuals related to the tractor and snowblower before operating. It is the owner's legal

obligation to instruct all operators in safe operation of the snowblower.

TRAINING

This symbol, "Safety Alert Symbol", is used

throughout this manual and on the

snowblower’s safety labels to warn of the

possibility of serious injuries. Please take

special care in reading and understanding the

safety precautions before operating the

snowblower or the tractor.

1. Read this owner's manual carefully. Be thoroughly

familiar with the controls and proper use of the

tractor and snowblower. Know how to stop the unit

and disengage the controls quickly.

2. Never allow children to operate snowblower nor the

tractor. Never allow adults to operate snowblower

nor the tractor without proper instructions.

3. No one should operate the tractor nor the

snowblower while intoxicated or while taking

medication that impairs the senses or reactions.

4. Keep the area of operation clear of all persons,

particularly small children and pets.

PREPARATION

1. Thoroughly inspect the area where the snowblower

is to be used and remove door mats, all foreign

objects and the like.

2. Disengage all clutches and shift into neutral before

starting engine.

3. Do not operate the snowblower without wearing

adequate winter outer garments. Avoid loose fitting

clothing that can get caught in moving parts. Wear

footwear that will improve footing on slippery

surfaces.

4. Handle fuel with care, it is highly flammable.

a) Use approved fuel container.

b) Never add fuel to a running engine or hot

engine.

c) Fill fuel tank outdoors with extreme care. Never

fill fuel tank indoors.

d) Never fill containers inside a vehicle, or on a

truck or a trailer bed with a plastic liner. Always

place containers on the ground, away from your

vehicle, before filling.

e) When practical, remove gas-powered equipment

from the truck or trailer and refuel it on the

ground. If this is not possible, then refuel such

equipment on a trailer with a portable container,

rather than from a gasoline dispenser nozzle.

f) Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times, until

refuelling is complete. Do not use a nozzle lock-

open device.

g) Replace fuel cap securely and wipe up spilled

fuel.

h) If fuel is spilled on clothing, change clothing

immediately.

5. Adjust the height of the snowblower to clear gravel

or crushed rock surface. This is done by adjusting

the skid shoes.

6. Never attempt to make any adjustments while the

engine (motor) is running (except when specifically

recommended by manufacturer).

7. Let engine (motor), tractor and snowblower adjust

to outdoor temperatures before starting to clear

snow.

8. Always wear safety glasses or eye shields during

operation or while performing an adjustment or

repair to protect eyes from foreign objects that may

be thrown from the snowblower.

9. Never modify the snowblower or any part

without the written consent from the

manufacturer.

OPERATION

1. Do not put hands or feet near or under rotating

parts. Keep clear of the discharge opening at all

times.

2. Exercise extreme caution when operating on or

crossing gravel drives, walks, or roads. Stay alert

for hidden hazards or traffic.

3. After striking a foreign object, stop the engine

(motor), disconnect the wire from the spark plug(s)

and keep wire away to prevent accidental starting.

Thoroughly inspect the snowblower for any damage

and repair damage before restarting and operating

the snowblower.

SAFETY PRECAUTIONS

4. If the unit should start to vibrate abnormally, stop

the engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

5. Stop the engine (motor) whenever you leave the

operating position, before unclogging the impeller/

collector housing or discharge chute, and when

making repairs, adjustments or inspections.

6. Take all possible precautions when leaving the

machine unattended. Disengage the power take-off,

lower the attachment, set the parking brake, shut

the engine off and remove the key.

7. When cleaning, unclogging, repairing or inspecting

the snowblower & tractor, make certain the

collector/impeller and all moving parts have

stopped. Disconnect wire from the spark plug(s)

and keep wire away to prevent accidental starting.

8. Do not run the engine indoors, except when

starting the engine and for transporting the

snowblower in or out of the building. Do not

operate or let motor run in a storage area without

ventilation because gas contains carbon monoxide

which is odourless, colorless and can cause death.

9. Do not clear snow across the face of slopes; go up

and down. Exercise extreme caution when

operating on slopes. Do not attempt to clear steep

slopes.

10. Never operate the snowblower without proper

guards, plates, or other safety protective devices in

place.

11. Never direct discharge at bystanders or operate

the snowblower near glass enclosures,

automobiles, window wells, drop-offs, and the like

without proper adjustment of the snow discharge

angle. Never allow anyone including children and

pets in the clearance area.

12. Do not overload the machine capacity by

attempting to clear snow at too fast a rate. Let the

snowblower ingest snow at its own rate.

13. Never operate the snowblower at high transport

speeds on slippery surfaces. Look behind and use

care when backing.

14. Do not carry passengers.

15. Disengage power to the collector /impeller to stop

all rotating parts when the snowblower is

transported or not in use.

MAINTENANCE AND STORAGE

1. Check shear bolts, engine mounting bolts, and

other bolts at frequent intervals for proper tightness

to be sure the snowblower is in safe working

condition.

2. Never store the machine with fuel in the fuel tank

inside a building where ignition sources are

present such as hot water and space heaters,

clothes dryers, and the like. Allow the engine to

cool before storing in any enclosure.

3. Always refer to the owner’s manual when you store

the snowblower for an extended period.

4. Maintain or replace safety and instruction labels,

as necessary.

5. Run the snowblower a few minutes after throwing

snow to prevent freeze-up of the rotating parts

such as collector/impeller.

WHENEVER YOU SEE THIS SYMBOL

IT MEANS:

WARNING!

BECOME ALERT !

YOUR SAFETY IS INVOLVED!

16. Use only accessories approved by the

manufacturer of the snowblower (such as wheel

chains, counterweights, cabs). You must use 100

lbs. of rear counterweight for better traction and a

greater stability at all times when using a

snowblower that is installed on the front of a

tractor.

17. Never operate the snowblower without good

visibility or light.

CLEARING A CLOGGED DISCHARGE CHUTE:

Hand contact with the rotating impeller inside the

discharge chute is the most common cause of injury

associated with snowblowers. Never use your hand to

clean out the discharge chute.

To clear the chute:

1. Lower snowblower to the ground and set parking

brake.

2. SHUT THE ENGINE OFF & REMOVE KEY!

3. Wait 10 seconds to be sure the all moving parts

such as the impeller blades have stopped moving.

4. Disconnect wire from the spark plug(s) and keep

wire away to prevent accidental starting.

5. Always use a clean-out tool of at least 36” in length,

NOT YOUR HANDS.

SAFETY DECALS

REPLACE IF DECALS ARE DAMAGED

SEE PARTS BREAKDOWN FOR DECAL LOCATION

Decal # 102125 Decal # 102126

Decal # 102127 Decal # 103951

Decal # 102124

Decal # 102128

ASSEMBLY

STEP 1

SNOWBLOWER PREPARATION:

Install the hand guard (item 1) in the chute (item 2) as

shown.

Secure in place with two 1/4 x 3/4" hex bolts, two flat

washers and two 1/4’’ flange nuts on the inside.

Tighten firmly.

Install chute

Install hand guard

Before installing the chute (item 1), loosen the two

flange nuts (item 2) (down to the last threads) which

holds the rotation system (item 3).

Install the rotation ring (item 4) over opening (item 5)

as shown and align the notches.

Place the chute (item 1) (facing the rear) and clip the

back over the rotation ring then turn the chute

towards the front to lock into place.

Reinstall the rotation system by tightening the flange

nuts firmly.

STEP 2

SNOWBLOWER INSTALLATION:

Refer to parts breakdown section for parts

identification.

ASSEMBLY

Remove the belt guard.

Install the belt on the pulleys as shown.

Install the belt on the drive mechanism pulley (item 5)

under the tractor.

NOTE: See belt instructions in the Maintenance

section.

Apply tension on the belt by pulling up the belt tension

arm.

Reinstall the belt guard.

Install belt

Item 1: Snowblower pulley

Item 2: V pulley

Item 3: Tension arm

Item 4: Flat pulley

Item 5: Drive mechanism pulley

Item 6: Flat pulley

CAUTION

Never use the snowblower without the belt guard.

CAUTION

The belt tension and lift assist spring arm are spring

loaded & need to be held firmly while displacing to

prevent injury.

WARNING

TO PREVENT INJURIES:

Stop the motor.

Apply parking brake.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent accidental

starting.

Attach the snowblower to the subframe as shown.

Make sure the snowblower is pushed in until locked

into place by the springs (item 3).

Lift the snowblower.

Turn the tension arm (item 1) towards the back and

install the chain (item 2) on the hook (if subframe is

equipped with one)

Turn the tension arm towards the front to apply

tension on the spring.

Lower the snowblower.

Install snowblower and lift assist spring

ASSEMBLY

VERIFY SKID SHOE ADJUSTMENT:

LEVEL PAVED SURFACE: Adjust skid shoes to

allow 3/16" to 1/4" clearance (A) between cutting

edge and surface.

UNEVEN OR GRAVEL SURFACE: Adjust skid

shoes to allow 1/2" to 5/8" clearance (A) between

cutting edge and surface.

VERIFY TIRE PRESSURE:

Check and adjust tractor tire pressure as follows:

Front tires: 14-15 psi

Back tires: 7-8 psi

Tire pressure must be even on both sides of tractor.

Install handle

Adjust skid shoes

Insert the handgrip (item 1) on the handle as shown.

Insert the handle hook (item 2) into the handle and

secure with a 2.5 mm hair pin (item 3) as shown.

VERIFY BELT ROUTING:

-Lower the snowblower to the ground and let it run for

a few seconds under supervision.

-Disengage the snowblower and stop the engine.

-Remove the belt guard.

-Check the belts to make sure they are well inserted

in the pulleys and that they have not flipped on their

sides on the pulleys and that they do not touch the

belt guides.

-Reinstall the belt-guard.

WARNING

TO PREVENT INJURIES:

It is the person who installs the drive mechanism

responsibility to make sure that when the clutch

is disengaged that all moving parts stop.

For more information, do not hesitate to contact

the technical support.

SNOWBLOWER OPERATION

a) Make sure the snowblower is clear of snow

before engaging the snowblower.

b) Make sure that the auger and impeller operate

freely.

c) Start the tractor engine.

d) Before engaging the snowblower drive, always

have the engine running at medium R.P.M.

e) Operate the snowblower at maximum engine

R.P.M.

IMPORTANT: USE FULL ENGINE R.P.M. WHEN

REMOVING WET OR STICKY SNOW. LOW R.P.M.

WILL TEND TO PLUG THE CHUTE.

CONTROLS

CHUTE ROTATION

The chute rotation handle is located to the left of

steering wheel. Turning the handle in a clockwise

direction, the discharge chute will turn in a clockwise

direction or vice versa.

CHUTE DEFLECTOR

Set the angle of the deflector according to the distance

the snow must be thrown and to prevent property

damage. To change the deflector angle, loosen the two

deflector knobs & adjust the deflector to the appropriate

angle and retighten the two knobs securely.

SNOW REMOVAL

When removing snow, do not use the snowblower as

a dozer blade to push snow. Allow snowblower to

ingest snow at its own speed. If the speed of your

tractor is too fast, the snowblower may become

overloaded and plug. For best results, raise the

snowblower and remove a top layer of snow. A

second pass with the snowblower will remove the

remaining snow.

OPERATION

WARNING

-Do not attempt to clear plugged chute, auger or

fan of snow while tractor engine is running.

-Disengage snowblower.

-Lower snowblower onto ground.

-Set the parking brake.

-Stop engine, remove the ignition key, disconnect

the wire from spark plug(s) and keep away from

spark plug(s) to prevent accidental starting.

-Make sure all moving parts have stopped.

-Do not use hand to unplug chute. Use a 36’’ (924

mm.) minimum length stick or board.

WARNING

Read the tractor Owner’s Manual carefully. Be

thoroughly familiar with the controls & proper

use of the attachment. Know how to stop the

attachment & disengage the controls quickly.

WARNING

TO PREVENT INJURIES AND FOR MORE

TRACTION WHEN USING AN ATTACHMENT:

-Rear counterweight of 100 lbs. minimum is

required to counterbalance the attachment’s

weight.

-Tractor manufacturer approved tire chains are

required.

-Do not operate on a slope greater than 10°.

-When dismounting the attachment remove rear

counterweights.

CUTTING EDGE MAINTENANCE

Verify from time to time the wearing on the cutting

edge to make sure you do not wear out the base of

the snowblower’s chassis. This cutting edge is

reversible. All you have to do is unscrew the bolts and

turn the cutting edge, reinstall and tighten the bolts

securely.

AUGERS AND FAN SHEAR BOLT

REPLACEMENT

Shear bolts are to be considered a preventive

measure and not an assured protection. Operator

vigilance is required. Thoroughly inspect the areas

where the snowblower is to be used and remove all

foreign objects.

To avoid damage to the snowblower:

Use only the original shear bolts (grooved bolts).

#104000 in bags of 10 for the augers.

#103999 in bags of 10 for the fan.

The use of any other shear bolt will not insure any

protection and may void the warranty.

MAINTENANCE

a) Check mounting bolts at frequent intervals for

proper tightness in order to prevent costly repairs.

Make sure your snowblower is in safe working

condition.

b) Provide adequate blocking before working under

snowblower when in raised position.

ADJUSTMENTS

SKID SHOE ADJUSTMENT:

Level Paved Surface: Adjust skid shoes to obtain 3/16"

to 1/4" clearance between cutting edge and surface.

Uneven or Gravel Surface: Adjust skid shoes to obtain

1/2" to 5/8" clearance between cutting edge and

surface.

LUBRICATION

Apply oil at all pivot points.

Chute Rotation System:

Oil chute base, rotation worm when necessary.

Gear box:

Check the oil annually. If necessary, add AGMA 5 EP or

SAE 90 oil.

The gear box should have a total of 155 ml of oil or filled

to the rim of the bolt hole when installed on the

snowblower.

WARNING

TO PREVENT INJURIES:

Stop the motor.

Apply parking brake.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent accidental

starting.

END OF SEASON STORAGE

a) Clean snowblower and subframe thoroughly and

repaint all parts from which paint has worn.

b) List the replacement parts that will be needed for

the next season.

c) Store the snowblower and the subframe in a dry

place.

d) Follow the instructions in the Lubrication section.

MAINTENANCE

BELT INSTALLATION, ADJUSTMENT,

AND REPLACEMENT:

SNOWBLOWER BELT:

a) Lower the snowblower to the ground.

b) Install the belt as shown.

c) Apply tension to the belt by pulling up the tension

arm (item 1).

After installation of the snowblower belt, make sure

there is enough tension on the belt. To obtain the

proper tension, the distance between the coils of

the spring should be .25’’ (1/4’’) approx.

If not, remove the bolt, sleeve and the spring (item

3) from the original hole and reinstall them in the

second hole (item 2). This will apply more tension

on the belt helping to prevent it from slipping in the

pulleys.

d)Engage the snowblower for a few seconds under

supervision. Stop the engine. Inspect the belt to

make sure it does not interfere with any parts; that it

is well inserted in the pulleys and that it has not

flipped on it’s side while still on the pulleys. The V

of the belt (A) must be in the V of the pulley (B).

The back of the belt (C) must rest on the flat pulley

(D).

e)Use genuine belts only, they are specifically

fabricated for this application.

f) Reinstall the belt guard.

g)To know the belt identification, please refer to the

subframe manual.

NOTE: Belts must be under high tension at all times.

If spring is damaged or stretched, you must replace it

DRIVE MECHANISM BELT:

See subframe manual for belt replacement

instructions.

CAUTION

The belt tension and lift assist spring arm are

spring loaded & need to be held firmly while

displacing to prevent injury.

Distance between coils

Belt installation

Belt Insertion Tension adjustment

DISMOUNTING

a) Remove the hair pin and the handle from the

rotation system.

b) Remove the belt guard and release the tension on

the belt by displacing the tension arm backwards.

The tension arm is spring loaded and needs to be

held firmly while lowering to prevent injuries.

Remove the belt.

c) Detach the snowblower by removing the lift assist

spring and by lifting the two spring locks on the

male quick hitch and pulling out the snowblower

one side at a time.

SNOWBLOWER DISMOUNTING

WARNING

TO PREVENT INJURIES:

Stop the motor.

Apply parking brakes.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent accidental

starting.

CAUTION

The belt tension and lift assist spring arm are

spring loaded & need to be held firmly while

displacing to prevent injury.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION

One section or both sections of the

auger stops turning.

Shear bolts are probably broken. Replace shear bolt (for

identification, see parts list

"Snowblower").

Fan stops turning. Shear bolt is probably broken. Replace shear bolt (for

identification, see parts list

"Snowblower").

Snowblower stops turning. One of the two belts is probably

damaged or broken.

Check both belts and replace

damaged belt(s) (for instructions,

see Maintenance section,

Installation, Adjustment and

Replacement section).

Belt has burn marks in specific

places.

Lack of tension on belt.

Snowblower engaged when

plugged.

Adjust manual clutch cable or

replace springs if stretched.

To obtain the proper tension, the

distance between the coils of the

spring should be .25’’ (1/4’’).

If not, remove the bolt, sleeve and

the spring from the original hole and

reinstall them in the second hole.

(See Maintenance section, Belt

installation, adjustment and

replacement).

Make sure the auger & the fan are

not frozen or plugged before

engaging.

Chute plugs easily. Tractor engine turning too slowly.

Advancing too quickly with tractor.

Run engine at full throttle during

snowblowing operation.

Allow snowblower to ingest snow at

its own speed.

Chute rotation is difficult. Dirt or ice may be underneath

chute.

Dismount chute by removing the

rotation worm (for identification, see

parts list "Chute with Rotation

System"). Turn the chute

completely towards the rear and it

will disconnect from base. Clean the

base of chute and the rotation ring.

Lubricate & re-install.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION

Snowblower digs into ground. Ground is not frozen or too soft. Adjust skid shoes lower so they

may better support the snowblower.

If problem persists, change skid

shoes for heavy duty skid shoes

(option #700243) which cover more

surface and prevents snowblower

from digging.

Snowblower does not raise evenly. Tire pressure uneven from one side

to another.

Maladjustment of the snowblower.

Verify and adjust tire pressure:

Front tires: 14 to 15 psi

Rear tires: 7 to 8 psi

Loosen male hitch on snowblower

(for identification, see parts list

"Snowblower").

Place a shim (ex.:piece of wood

approx. 2” thick) under the lowest

side of snowblower which needs to

be leveled. Re-tighten bolts.

Snowblower vibrates or is

abnormally noisy.

Damaged pulley.

Damaged bearing.

Damaged fan.

Damaged auger.

Replace pulley.

Replace bearing.

Dismount & repair or replace fan.

Replace auger.

GENERAL TORQUE SPECIFICATION TABLE

USE THE FOLLOWING TORQUES WHEN SPECIAL TORQUES ARE NOT GIVEN

NOTE: These values apply to fasteners as received from supplier, dry or when lubricated with normal oil. They do not apply if

special graphited or moly disulphide greases or other extreme pressure lubricants are used. This applies to both UNF and UNC

threads.

TORQUE SPECIFICATION TABLE

SEE Grade No. 2 5 8 *

BOLT HEAD

IDENTIFICATION

MARKS AS PER GRADE

NOTE MANUFACTURING

MARKS WILL VARY

TORQUE TORQUE TORQUE

BOLT SIZE POUNDS FEET NEWTON-METERS POUNDS FEET NEWTON-METERS POUNDS FEET NEWTON-METERS

Inches Millimetre Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Max. Min. Max. Max.

1/4" 6.35 5 6 6.8 8.13 911 12.2 14.9 12 15 16.3 30.3

5/16" 7.94 10 12 13.6 16.3 17 20.5 23.1 27.8 24 29 32.5 39.3

3/8" 9.53 20 23 27.1 31.2 35 42 47.5 57 45 54 61 73.2

7/16" 11.11 30 35 40.7 47.4 54 64 73.2 86.8 70 84 94.9 113.9

1/2" 12.7 45 52 61 70.5 80 96 108.5 130.2 110 132 149.2 179

9/16" 14.29 65 75 88.1 101.6 110 132 149.2 179 160 192 217 260.4

5/8" 15.88 95 105 128.7 142.3 150 180 203.4 244.1 220 264 298.3 358

3/4" 19.05 150 185 203.3 250.7 270 324 366.1 439.3 380 456 515.3 618.3

7/8" 22.23 160 200 216.8 271 400 480 542.4 650.9 600 720 813.6 976.3

1" 25.4 250 300 338.8 406.5 580 696 786.5 943.8 900 1080 1220.4 1464.5

*Thick nuts must be used with grade 8 bolts

METRIC BOLT TORQUE SPECIFICATIONS

COARSE THREAD

Size Screw Grade No. Pitch (mm) Pounds Feet Newton-Meters Pitch (mm) Pounds Feet Newton-Meters

M6 4T 1.00 3.6 - 5.8 4.9 - 7.9 - - -

7T 5.8 - 9.4 7.9 - 12.7 - -

8T 7.2 - 10 9.8 - 13.6 - -

M8 4T 1.25 7.2 - 14 9.8 - 19 1.00 12 - 17 16.3 - 23

7T 17 - 22 23 - 29.8 19 - 27 25.7 - 36.6

8T 20 - 26 27.1 - 35.2 22 - 31 29.8 - 42

M10 4T 1.50 20 - 25 27.1 - 33.9 1.25 20 - 29 27.1 - 39.3

7T 34 - 40 46.1 - 54.2 35 - 47 47.4 - 63.7

8T 38 - 46 51.5 - 62.3 40 - 52 54.2 - 70.5

M12 4T 1.75 28 - 34 37.9 - 46.1 1.25 31 - 41 42 - 55.6

7T 51 - 59 69.1 - 79.9 56 - 68 75.9 - 92.1

8T 57 - 66 77.2 - 89.4 62 - 75 84 - 101.6

M14 4T 2.00 49 - 56 66.4 - 75.9 1.50 52 - 64 70.5 - 86.7

7T 81 - 93 109.8 - 126 90 - 106 122 - 143.6

8T 96 - 109 130.1 - 147.7 107 - 124 145 - 168

M16 4T 2.00 67 - 77 90.8 - 104.3 1.50 69 - 83 93.5 - 112.5

7T 116 - 130 157.2 - 176.2 120 - 138 162.6 - 187

8T 129 - 145 174.8 - 196.5 140 - 158 189.7 - 214.1

M18 4T 2.00 88 - 100 119.2 - 136 1.50 100 - 117 136 - 158.5

7T 150 - 168 203.3 - 227.6 177 - 199 239.8 - 269.6

8T 175 - 194 237.1 - 262.9 202 - 231 273.7 - 313

M20 4T 2.50 108 - 130 146.3 - 176.2 1.50 132 - 150 178.9 - 203.3

7T 186 - 205 252 - 277.8 206 - 242 279.1 - 327.9

8T 213 - 249 288.6 - 337.4 246 - 289 333.3 - 391.6

FINE THREAD

PARTS BREAKDOWN / NOMENCLATURE DES PIÈCES

CHUTE WITH ROTATION SYSTEM /

GOULOTTE AVEC SYSTÈME DE ROTATION

PARTS LIST / LISTE DES PIÈCES

O/L = Obtain locally/obtenir localement

REF.

RÉF. DESCRIPTION DESCRIPTION QTY

QTÉ

PART #

PIÈCE #

1Chute Goulotte 1103936

2Rotation bushing Coussinet de rotation 2103945

3Rotation worm Spirale de rotation 1102005

4Worm support Support spirale 1103941

5Worm support Support spirale 1103942

6Rotation ring Anneau de rotation 1103943

7Carriage bolt 1/4" n.c. x 1" Boulon à carrosserie 1/4" n.c. x 1" 2O/L

8Flange nut 1/4" n.c. Écrou à bride 1/4" n.c. 4O/L

9Nylon flat washer 7/16" Rondelle plate de nylon 7/16" 2102011

10 Carriage bolt 5/16" n.c. x 3/4" Boulon à carrosserie 5/16" n.c. x 3/4" 2O/L

11 Nylon flat washer 11/32" Rondelle plate de nylon 11/32" 2102009

12 Knob Bouton 2102020

13 Hand guard Fourche protectrice 1102012

14 Hex. bolt 1/4" n.c. x 3/4" Boulon hex. 1/4" n.c. x 3/4" 2O/L

15 Flat washer 5/16" hole Rondelle plate 5/16" trou 2O/L

16 Handle hook Crochet de manivelle 1102006

17 Handle Manivelle 1102061

18 Hair pin 2.5mm Goupille à ressort 2.5mm 1102013

19 Handgrip Poignée 1102062

20 Danger decal Décalque danger 1102127

21 Warning decal Décalque attention 1102125

PARTS BREAKDOWN / NOMENCLATURE DES PIÈCES

SNOWBLOWER / SOUFFLEUSE

La page charge ...

Bercomac 700374 700378 Manuel utilisateur

Marque: Bercomac

Modèle: 700374 700378

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Bercomac 700374 700378 User manual

Bercomac 700374 700378 Manuel utilisateur

Bercomac 700374 700378 Manuel utilisateur

dans d''autres langues

Documents connexes