Bercomac 700310-5 Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur
1
Kimpex
Two Stage 48" Snowblower
For
ALL TERRAIN VEHICLES
CAUTION:
READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE
OPERATING YOUR EQUIPMENT
104303 G-06
* ASSEMBLY * REPAIR PARTS
* OPERATION * MAINTENANCE
OWNER’S MANUAL
Model Number
058121
700310-5
2
Conditions and Products Covered:
KIMPEX guarantees any part of the product or accessory
manufactured by KIMPEX and found in the reasonable
judgment of KIMPEX to be defective in material and or
workmanship will be repaired or replaced by an authorized
dealer without charge up to our maximum labor rates and pre-
established times. For replacement parts only standard
ground freight services are covered. This warranty extends to
the original retail purchaser only and is not transferable to any
subsequent purchasers.
Warranty Period
(from date of the original retail purchase):
Residential use: 1 year
Commercial or rental use: 90 days
Exceptions Noted Below: the following items are guaranteed
by the original manufacturer and have their own warranty,
conditions and limited time.
Tire Chains: 90 days
Engines (supplied with KIMPEX equipment): 2 years
Please refer to the engine manufacturer’s warranty
statement included with the unit. KIMPEX is not authorized
to handle warranty adjustments on engines.
Items and Conditions NOT Covered:
This warranty does not cover the following:
Pick-up or delivery charges or in-home services fees.
Any damage or deterioration of the unit, parts and or finish
of these due to normal use, wear and tear, or exposure.
Cost of regular use or maintenance service or parts, such
as gas, oil, lubricants, tune-up parts, and adjustments.
Any part or accessory which has been altered, modified,
misused, neglected, accidentally damaged or not properly
installed, maintained, stored or repaired not in accordance
with the instructions in the owner’s manual.
Repair due to normal wear and or any wear items such as
shear pins, bolts, belts, etc.
Expedited freight fee services for replacement parts.
Shear bolts and shear pins are to be considered as a
preventive measure not as an assured protection, any
damages resulting from the lack of shear bolts breakage
are not covered.
NOTE: All warranty work must be performed by an authorized
dealer using original (manufacturer) replacement parts.
Owner’s Responsibilities:
KIMPEX’s defective equipment or part must be returned to an
authorized dealer within the warranty period for repairs. In the
event that defective merchandise must be returned to
manufacturer for repairs, freight fees are prepaid and a written
authorization from KIMPEX must be obtained by KIMPEX prior
to the shipment. This warranty extends only to equipment
operated under normal conditions. To validate a warranty
claim, it is the user’s responsibility to maintain and service the
unit as specified in the owner’s manual at their expense.
General Conditions:
The sole liability of KIMPEX with respect to this warranty shall
be strictly and exclusively repair and replacement as
mentioned herein. KIMPEX shall not have any liability for any
other costs, loss or damage, including but not limited to, any
incidental or consequential loss or damage.
In particular, without being limited to, KIMPEX shall have no
liability or responsibility for:
Travel time, overtime, after hours time or other extraordinary
repair charges or relating to repairs and or replacements
outside of normal business hours.
Rental of like or similar replacement equipment during the
period of any, repair or replacement work.
Any communicating or travel charges.
Loss or damage to person or property other than that
covered by the terms of this warranty.
Any claims for lost revenue, lost profit or any similar costs
as a result of damage or repair.
Attorney’s fees.
KIMPEX’s responsibility in respect to claims is limited to
making the required repairs or replacement without charge up
to our maximum labor rates and pre-established times and no
claim of breach of warranty shall be cause for cancellation or
rescission of the contract of sale of any product or accessory.
This warranty gives you specific legal rights. You may also
have other rights, which vary from state to state.
Note: KIMPEX reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify
any product previously manufactured.
Instructions for Obtaining Warranty Services:
Contact dealer where equipment was purchased or any other KIMPEX Service Dealer to arrange service at their dealership. To locate
a dealer convenient to you, access our website at www..kpx-kimpex.com.
Kimpex Inc., 5355, St-Roch, Drummundville, QC, Canada J2B 6V4
Bring the product and your proof of purchase (sales receipt) to the KIMPEX dealer.
LIMITED WARRANTY
1
TABLE OF CONTENTS
INTRODUCTION .................................................................................................................................................... 2
SAFETY PRECAUTIONS ...................................................................................................................................... 3
SAFETY DECALS .................................................................................................................................................. 5
ASSEMBLY
Step 1: Snowblower Preparation ............................................................................................................ 6
Step 2: Subframe Preparation ................................................................................................................. 9
Step 3: Engine Installation ....................................................................................................................... 11
Step 4: Installation on the vehicle ............................................................................................................ 17
OPERATION
Operating the Snowblower ....................................................................................................................... 20
Controls ..................................................................................................................................................... 20
Removing Snow ........................................................................................................................................ 20
MAINTENANCE
Maintenance .............................................................................................................................................. 21
Adjustments .............................................................................................................................................. 21
Lubrication ................................................................................................................................................. 21
Cutting Edge Maintenance ....................................................................................................................... 21
Shear Bolt Replacement .......................................................................................................................... 21
Storage ...................................................................................................................................................... 21
BELT REPLACEMENT & ADJUSTMENTS .......................................................................................................... 22
TROUBLESHOOTING ........................................................................................................................................... 23
MOUNTING BRACKET CHART ............................................................................................................................ 25
TORQUE SPECIFICATION TABLE ...................................................................................................................... 27
PARTS BREAKDOWN AND PARTS LIST
Rotation System with Chute ..................................................................................................................... 28
Manual Clutch Mechanism ....................................................................................................................... 30
Subframe ................................................................................................................................................... 32
Snowblower ............................................................................................................................................... 34
OPTIONS & ATTACHMENTS ……. ...................................................................................................................... 38
PAGE
2
INTRODUCTION
TO THE PURCHASER
This new attachment was carefully designed to give years of dependable service. This manual has been provided to
assist in the safe operation and servicing of your attachment.
NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but
are intended for reference only and are based on the latest product information available at the time of publication.
Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to use.
Carefully read, understand and follow these recommendations and insist that they be followed by those who will use
this attachment.
THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS MANUAL
THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH. DANGER,
WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF HAZARD.
HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.
DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions are
not followed.
WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are not
followed.
CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are not
followed.
Record your attachment serial number and purchase date in the section reserved below (there is no serial number on
the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement
parts. Use only genuine parts when replacements are required.
If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer
for warranty service.
This manual should be kept for future reference.
Please check if you have received all the parts for your kit with the list of the
bag and the list of the box.
7
SERIAL NUMBER : ___________________________
PURCHASE DATE : ___________________________
In this manual, right and left sides are determined by sitting on the vehicle seat facing forward.
3
SAFETY PRECAUTIONS
Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle.
and snowblower. This snowblower is capable of amputating hands and feet and throwing objects. Failure to observe
the following safety instructions could result in serious injury. All operators, no matter how experienced they may be,
should read this and other manuals related to the vehicle and attachments before operating. It is the owner's legal
obligation to instruct all operators in safe operation of the snowblower.
TRAINING:
This symbol, "Safety Alert Symbol", is used
throughout this manual and on the snowblower’s
safety labels to warn of the possibility of serious
injury. Please take special care in reading and
understanding the safety precautions before
operating the snowblower or the vehicle.
1. Read this owner's manual carefully. Be thoroughly
familiar with the controls and proper use of the
vehicle and snowblower. Know how to stop the
unit and disengage the controls quickly.
2. Never allow children to operate snowblower nor the
vehicle. Never allow adults to operate snowblower
nor the vehicle without proper instructions.
3. No one should operate the vehicle nor the
snowblower while intoxicated or while taking
medication that impairs the senses or reactions.
4. Keep the area of operation clear of all persons,
particularly small children and pets.
PREPARATION:
1. Thoroughly inspect the area where the
snowblower is to be used and remove door mats,
all foreign objects and the like.
2. Disengage all clutches and shift into neutral before
starting engine.
3. Do not operate the snowblower without wearing
adequate winter outer garments. Avoid loose fitting
clothing that can get caught in moving parts. Wear
footwear that will improve footing on slippery
surfaces.
4. Handle fuel with care, it is highly flammable.
a) Use approved fuel container.
b) Never add fuel to a running engine or hot engine.
c) Fill fuel tank outdoors with extreme care. Never
fill fuel tank indoors.
d) Never fill containers inside a vehicle, or on a
truck or a trailer bed with a plastic liner.
Always place containers on the ground, away
from your vehicle, before filling.
7
OPERATION:
1. Do not put hands or feet near or under rotating
parts. Keep clear of the discharge opening at all
times.
2. Exercise extreme caution when operating on or
crossing gravel drives, walks or roads. Stay alert for
hidden hazards or traffic.
3. After striking a foreign object, stop the engine
(motor), disconnect the wire from the spark plug(s)
and keep wire away to prevent accidental starting.
Thoroughly inspect the snowblower for any damage
and repair damage before restarting and operating
the snowblower.
e) When practical, remove gas-powered equipment
from the truck or trailer and refuel it on the
ground. If this is not possible, then refuel such
equipment on a trailer with a portable container,
rather than from a gasoline dispenser nozzle.
f) Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times, until
refueling is complete. Do not use a nozzle lock-
open device.
g) Replace fuel cap securely and wipe up spilled
fuel.
h) If fuel is spilled on clothing, change clothing
immediately.
5. Adjust the height of the snowblower to clear gravel or
crushed rock surface. This is done by adjusting the
skid shoes.
6. Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by manufacturer).
7. Let engine (motor) of the vehicle and snowblower
adjust to outdoor temperatures before starting to
clear snow.
8. Always wear safety glasses or eye shields during
operation or while performing an adjustment or
repair to protect eyes from foreign objects that may
be thrown from the machine.
9. Never modify the snowblower or any part
without the written consent from the
manufacturer.
4
SAFETY PRECAUTIONS
4. If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the cause.
Vibration is generally a warning of trouble.
5. Stop the engine (motor) whenever you leave the
operating position, before unclogging the impeller/
collector housing or discharge chute, and when
making repairs, adjustments or inspections.
6) Take all possible precautions when leaving the
machine unattended. Disengage the power take-off,
lower the attachment, set the parking brake, stop the
engine and remove the key.
7. When cleaning, unclogging, repairing or inspecting,
the snowblower and vehicle, make certain the
collector/impeller and all moving parts have
stopped. Disconnect wire from the spark plug(s) and
keep wire away to prevent accidental starting.
8. Do not run the engine indoors, except when starting
the engine and for transporting the snowblower in or
out of the building. Do not operate or let motor run in
a storage area without ventilation because gas
contains carbon monoxide which is odourless,
colorless and can cause death.
9. Do not clear snow across the face of slopes; go up
and down. Exercise extreme caution when
changing direction on slopes. Do not attempt to
clear steep slopes.
10.Never operate the snowblower without proper
guards, plates, or other safety protective devices
in place.
11.Never direct discharge at bystanders or operate
the snowblower near glass enclosures,
automobiles, window wells, drop-offs, and the like
without proper adjustment of the snow discharge
angle. Never allow anyone including children and
pets in the clearance area.
12.Do not overload the machine capacity by
attempting to clear snow at too fast a rate. Let the
snowblower ingest snow at its own rate.
13.Never operate the snowblower at high transport
speeds on slippery surfaces. Look behind and use
care when backing.
14.Do not carry passengers.
15.Disengage power to the collector/impeller to stop
all rotating parts when the snowblower is
transported or not in use.
WHENEVER YOU SEE THIS SYMBOL
7
IT MEANS:
WARNING!
BECOME ALERT !
YOUR SAFETY IS INVOLVED!
16.Use only accessories approved by the
manufacturer of the snowblower (such as wheel
chains, and the like).
17.Never operate the snowblower without good
visibility or light.
CLEARING A CLOGGED DISCHARGE CHUTE:
Hand contact with the rotating impeller inside the
discharge chute is the most common cause of injury
associated with snowblowers. Never use your hand to
clean out the discharge chute.
To clear the chute:
1. Lower snowblower to the ground and set parking
brake.
2. SHUT THE ENGINE OFF & REMOVE KEY!
3. Wait 10 seconds to be sure the all moving parts
such as the impeller blades have stopped moving.
4. Disconnect wire from the spark plug(s) and keep
wire away to prevent accidental starting.
5. Always use a clean-out tool of at least 36” in
length, NOT YOUR HANDS.
MAINTENANCE AND STORAGE
1. Check shear bolts, engine mounting bolts, and
other bolts at frequent intervals for proper
tightness to be sure the snowblower is in safe
working condition.
2. Never store the machine with fuel in the fuel tank
inside a building where ignition sources are
present such as hot water and space heaters,
clothes dryers, and the like. Allow the engine to
cool before storing in any enclosure.
3. Always refer to the owner’s manual for the motor
and snowblower when they are to be stored for
an extended period.
4. Maintain or replace safety and instruction labels,
as necessary.
5. Run the snowblower a few minutes after throwing
snow to prevent freeze-up of the rotating parts
such as collector/impeller.
5
SAFETY DECALS
Decal # 102125 Decal # 102126
Decal # 102127 Decal # 102553
REPLACE IF DECALS ARE DAMAGED
SEE PARTS BREAKDOWN FOR DECAL LOCATION
Decal # 102671
Decal # 102128
6
ASSEMBLY
IMPORTANT: TORQUE ALL BOLTS ACCORDING
TO TORQUE SPECIFICATION TABLE (SEE TABLE
OF CONTENTS) WHEN STATED: TIGHTEN
FIRMLY. REFER TO PARTS BREAKDOWN
SECTION FOR PART IDENTIFICATION.
STEP 1
SNOWBLOWER PREPARATION:
Place snowblower face down.
Install the hitch (item 1) with three 7/16 x 1 1/4" bolts
(item 2), lock washers, nylon insert locknuts and a
7/16 x 1 1/4" bolt with a flat washer (item 3) over the
slot, lock washer and a nylon insert locknut as shown.
Tighten the bolts firmly.
Turn the snowblower upright.
Place the rotation ring (item 1) on top of the
snowblower (item 2) as shown.
Only one position provides a perfect fit.
Install hitch
Install rotation ring
Place snowblower face down
7
ASSEMBLY
Grease both ends of the rotation worm (item 1).
Insert the short rotation bushing (item 2) and the long
rotation bushing (item 3) as shown.
Insert the rotation worm with the short bushing in the
sleeve (item 1).
Insert the rotation worm support (item 2) on the long
bushing as shown.
Apply grease on the rotation ring (item 1).
Install the chute (item 2) with four retaining plates
(item 3) as shown.
At the rear left hand corner, secure a retaining plate
(item 3) on top and the rotation worm support (item 5)
underneath with two 1/4 x 3/4" bolts (item 4) and
flange nuts as shown.
Secure the other three retaining plates (item 3) with
six 1/4 x 1/2" bolts (item 6) and flange nuts.
Tighten the bolts firmly.
Install chute
Insert bushings on rotation worm
Install rotation worm
8
ASSEMBLY
Install the hand guard (item 1) as shown.
Secure in place with two 1/4 x 3/4" bolts (item 2) the
flatwashers and flange nuts inside.
Tighten the bolts firmly.
Install hand guard
9
ASSEMBLY
STEP 2
SUBFRAME PREPARATION:
Install the two caster wheels (item 1) to the wheel
support (item 2) as shown.
NOTE: If your vehicle is equipped with cat tracks,
do not install the chains now.
Install the two 3/16 x 32" chains (item 3) to the top of
the plate of the wheel support with a 3/8 x 1" bolt
(item 4) and a flat washer in the inside rear hole of the
wheel support.
Install three 3/8 x 3/4" bolts (item 5) in the other holes
and secure with the flange nuts.
Tighten firmly.
Install the subframe (item 2) to the wheel support
(item 1) with four 7/16 x 1" bolts (item 3), lock
washers and nuts.
Tighten the bolts firmly.
Install wheels and chains
Install the subframe to the wheel support
Install pivot support
Install the wheel support (item 1) to the snowblower’s
pivot support (item 2) with two 1" dia x 0.31" sleeves
(item 3) and two 1/2 x 1 1/2" bolts (item 4), flat wash-
ers, lock washers and nuts.
Tighten firmly.
10
ASSEMBLY
Install the subframe extension (item 2) to the
subframe (item 1) using eight 3/8 x 3/4” hex bolts
(item 3) and nylon nuts.
Tighten firmly.
NOTE: This subframe extension is adjustable in
order to install cat tracks on the vehicle.
Adjust to the appropriate length to your vehicle.
Example:
Vehicle with wheels: adjust subframe to its shortest.
Vehicle with cat tracks: adjust subframe to its longest.
OTHER VEHICULES:
Please take note that certain modifications might be
necessary to adapt the snowblower to other vehicles
with this subframe extension.
****THE MANUFACTURER’S WARRANTY
ON THE SNOWBLOWER DOES NOT
COVER THESE MODIFICATIONS.****
Install the subframe extension (item 2) to the
subframe (item 1) using eight 3/8 x 3/4” hex bolts
(item 3) and nylon nuts.
Tighten firmly.
For vehicle equipped with cat tracks:
Install the chain adaptor (item 1) on the subframe
(item 2) with two 3/8 x 1’’ hex bolts (item 3). Secure
with two 3/8’’ nylon insert lock nuts.
Attach the chains (item 4) on the top of the chain
adaptor with two 3/8 x 1 1/4’’ hex bolts (item 5) and
two flat washers (item 6) on the chain. Secure with
two 3/8’’ nylon insert lock nuts.
Install subframe extension for A.T.V.s
Install adaptor & chains
Install subframe extension for other vehicle
11
STEP 3
ENGINE INSTALLATION:
NOTE: THE RIGHT INSTALALTION OF THE ENGINE IS CRUCIAL TO THE GOOD WORKING
ORDER OF THE SNOWBLOWER.
Figure 1
Engine not in right position
Figure 2
Engine not in right position
NOTE: Figures 1 and 2 show an engine that is not
well positioned.
IMPORTANT: We recommend using a 13 H.P.
motor on this snowblower.
DO NOT USE A MOTOR BIGGER THAN A 13 HP,
THE PULLEYS AND BELTS ARE CALIBRATED
FOR A 13 HP MOTOR AND NOT BIGGER,
Remove the belt guide stopper (item 1) and the belt
guard (item 2).
ASSEMBLY
Remove belt guard
12
ENGINE INSTALLATION, (HONDA, BRIGGS &
STRATTON OR TECUMSEH) 13 HP
Install the engine on the stand, using the holes
identified as item A.
Secure with four 3/8 x 1 1/2" bolts, two flat washers
(over the slot) and nuts.
NOTE: Make sure the side of the base of the engine
is parallel with the snowblower’s body.
Tighten the bolts firmly.
Install engine
ASSEMBLY
INSTALLATION OF OTHER BRANDS OF
ENGINES:
Place the engine on a table. Measure the height (item
B) from the middle of the crank shaft to the table. Use
one of the two shims (3/4" or 1") if required, to attain
the height of 5.25". If more or less height is needed,
use a couple of flat washers.
Install the engine and shims on the stand. Choose the
set of holes that correspond with the holes at the
base of the engine.
The center of the crank shaft must be 5.75" from the
back of the snowblower.
Make sure that the base of the motor is parallel with
the snowblower frame.
Install engine
13
ASSEMBLY
After positioning the engine, the axes must be parallel
as shown in figures 1 and 2.
(Use some shims if necessary).
NOTE: It is very important that the pulleys are
aligned (as shown in the two views: back view of
the snowblower (fig. 1) and the top view of the
snowblower (fig. 2).
No adjustments can be made on the bottom
pulley (fig. 1, item 3).
Install the 2 1/2" pulley (item 2) on the motor shaft as
shown (hub towards the engine) with a 1/4" x 1/4" x 1
3/4" key so that the belts are parallel with the ruler.
Hold a ruler (fig.1, item A) on the double pulley (item
3).
Tighten the set screw firmly. Figure 1
Back view of
snowblower
Figure 2
Top view of snowblower
14
ASSEMBLY
Adjust the idler pulley as follows:
After installing the belts, you may run the engine
without the belt guard but only for the time needed to
verify the belt alignment and only under strict
supervision.
Do not approach (you or anyone else) the moving
parts. Engage and disengage the snowblower to
verify if the belts are well aligned, especially on the
idler pulley.
If necessary you can add or remove a flat washer for
final adjustment on the idler pulley (item 2).
Figure 1
Back view of snowblower
7 DANGER 7
Without the belt guard and belt guide stopper in
place, the snowblower will not stop or will stop
too slowly when you disengage the clutch.
Adjust the clutch cable (item 1). The distance (item B)
between the cable end (item 3) and the cable support
should be 1/4’’ (.250") to 5/16’’ (.312") when in the
engaged position.
If not, adjust the cable (item 1) by extending the cable
adjustment (See instructions on p.22). If the cable
adjustment is at its limit, unhook the spring (item 2)
and remove the cable end (item 3). Shorten the cable
adjustment. Cut the inner cable 1 1/4" longer than the
shield and reinstall as removed. Reinstall the cable
end with the hex socket set screw. Do not tighten too
firmly the hex socket set screw, if too tight it might cut
the inner cable.
Verify the adjustment.
NOTE: If there is not enough tension on the
spring (item 2) the belts will slip and be ruined.
NOTE: When the belt guide stopper is installed, the
belt should clear the pins (items 4) by 1/8’’ (.125")
when the clutch arm is in the engaged position.
Adjust clutch cable
15
ASSEMBLY
NOTE: The clutch arm must be engaged (pulled
towards the driver) before installing the belt guide
stopper, if not the belts will be destroyed.
Install the belt guard (item 2) and secure in place with
the rubber latch (item 1).
Install the belt guide stopper (item 3) (belts inside the
pins) and secure with lock washer and wing nut.
Disengage the clutch.
Install belt guard and belt guide stopper
7 DANGER 7
Never let the snowblower motor run without the
belt guard & belt guide stopper in place.
7 WARNING 7
TO PREVENT INJURIES:
Start the engine, engage and disengage the
clutch to be sure if functions normally.
This means when you disengage the clutch, the
snowblower will stop immediately .
16
ASSEMBLY
STEP 4
INSTALLATION ON THE VEHICULE:
Install the optional quick hitch mounting brackets
(item 1) under the vehicle. Refer to the Mounting
Bracket Chart to identify the proper bracket model for
your vehicle. (see table of contents).
Follow the mounting instructions supplied with the
mounting bracket kit.
DO NOT INSTALL THE OTHER ITEMS.
Carefully drive the vehicle over the subframe.
Hook the subframe (item 1) to the quick hitch bracket
(item 2) and secure in place with the handle locks
(item 3).
Attach the chains with the shackles (item 4) to the
vehicle ’s suspension to prevent the snowblower from
swaying side to side.
NOTE: Do not install the chains to the front
bumper of the vehicle.
Chains must be tight and crossed horizontally,
parallel to the ground as shown.
Install subframe on A.T.V
Install subframe on other vehicle
Install optional quick hitch
17
ASSEMBLY
LIFT THE SNOWBLOWER USING THE A.T.V.’S
WINCH:
NOTE: Optional kit #700269 Lift connection kit (items
1 & 2) must be used. This kit will double the winch’s
lifting and braking capacity and reduces the lifting
speed by 50%. This will prevent damage to the
snowblower’s engine.
Hook the pulley block (item 2) into the hole on the flat
bar welded on top of the snowblower (item 3).
Remove the pulley from the block to pass the winch
cable through the pulley block. Use the nylon strap
(item 1) supplied in the kit to attach the winch cable to
the vehicle's chassis.
If the winch is located lower than the pulley block on
the snowblower, attach the cable in the highest
position possible on the vehicle’s chassis.
If the winch is located higher than the pulley block on
the snowblower, attach the cable in the lowest
position possible on the vehicle’s chassis.
If snowblower doesn’t raise evenly see below for
instructions.
VERIFY IF SNOWBLOWER RAISES EVENLY
If snowblower does not raise evenly, follow these
instructions:
Loosen the eight bolts (items 1 & 2, four on each
side) which hold the push frame (item 3).
Lift the engine side of the snowblower and slide a 1
1/2" (approx.) piece of wood underneath.
Tighten the eight bolts very firmly (torque to 65 lbs/ft).
The snowblower should raise evenly. If not, repeat
the procedure using thicker or thinner pieces of wood
depending on the weight of the engine.
Install lift connection kit
Verify if the snowblower raises evenly
18
ASSEMBLY
NOTE: To install the clutch controls and the rotation
arm support on a vehicle which has a plastic rack
(item 1), you must purchase the optional kit "Control
support" (item 2).
Install the handle support (item 3) with the support
bracket (item 2) using the 1/4 x 3/4" hex. bolts and
nuts on the left hand side of the vehicle’s rack.
Choose the ideal place and make sure the hand
crank is easily accessible and does not interfere with
the steering handlebars.
Install the 1/2 x 3" handgrip (item 1) on the handle
(item 5).
Insert the handle through the hole in the handle
support (item 3).
Install the handle hook (item 6) on the rotation worm
(item 7).
Insert the hook on the rotation handle and lock in
place with a 2.5 mm hair pin (item 4).
Install the clutch holder (item 1) on the right hand side
of the vehicle’s front rack.
Identify where is the best place, making sure the
driver has easy access to the controls.
Wrap the rubber pads (item 2) over the tube if
necessary.
Install the clutch holder (item 1) on the tube over the
rubber pads with the round hole (item 3) towards the
front.
Secure with a 5/16 x 1 3/4" carriage bolt (item 4), in
the front hole. Secure with nut and tighten lightly.
The space between the bolt head and the brace is
intentional and is designed to attach the clutch
support. Install a 5/16 x 1 3/4" carriage bolt (item 6) in
the rear square hole (item 5) and secure with the
knob (item 7).
The clutch holder should be exactly 90° parallel with
the ground.
Using the support as a template, drill through the tube
and secure with two 1/4 x 1 1/4" hex bolts (item 8)
and nuts.
Tighten firmly.
Install handle
Install clutch holder
Control support
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Bercomac 700310-5 Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur

dans d''autres langues