Lennox Indoor Fireplace MPB3328CNE-B Manuel utilisateur

Marque: Lennox

Modèle: Indoor Fireplace MPB3328CNE-B

Catégorie: Cheminées

Taper: Manuel utilisateur

OTL Report No. 116-F-36-5

Portland

MODELS

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile

home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating

plate. This appliance is not convertible for use with other gases unless a certiﬁed kit is used.

INSTALLATION INSTRUCTIONS

MPB B-Vent

Gas Fireplaces

MPB3328CNM-B

MPB3328CPM-B

MPB3530CNM-B

MPB3530CPM-B

MPB4035CNM-B

MPB4540CNM-B

MILLIVOLT:

MPB3328CNE-B

MPB3530CNE-B

MPB4035CNE-B

MPB4540CNE-B

ELECTRONIC:

P/N 850033M Rev. G 01/2011

This manual is one of a set of two supporting this product.

Refer to P/N 875031M for Care and Operation Instructions.

Ce manuel est disponible en francais, simplement

en faire la demande. Numéro de la pièce 850033CF.

AVERTISSEMENT : Assurez-vous de bien suivre les

instructions données dans cette notice pour réduire au

minimum le risque d’incindie ou d’explosion ou pour

éviter tout dommage matériel, toute blessure ou la mort.

- Ne pas entreposer ni utilizer d’essence ni d’autres vapeurs

ou liquides inﬂammables dans le voisinage de cet appareil

ou de tout autre appareil.

- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous servir des

téléphones se trouvant dans le bâtiment où vous trouvez.

• Appelez immédiatement votre fournisseur de gaz depuis

un voisin. Suivez les instructions du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service des incindies.

L’installation et l’entretien doivent être assurés par un

installateur ou un service d’entretien qualiﬁé ou par le

fournisseur de gaz.

WARNING: If the information in these instructions

is not followed exactly, a ﬁre or explosion may

result, causing property damage, personal injury,

or death.

vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

•

department.

- Installation and service must be performed by a

WARNING

AVERTISSEMENT

AVISO

• HOT GLASS WILL CAUSE

BURNS.

• DO NOT TOUCH GLASS

UNTIL COOLED.

• NEVER ALLOW CHILDREN

TO TOUCH GLASS.

• UNE SURFACE VITRÉE CHAUDE

PEUT CAUSER DES BRÛLURES.

• LAISSER REFROIDIR LA SURFACE

VITRÉE AVANT D'Y TOUCHER.

• NE PERMETTEZ JAMAIS À UN ENFANT

DE TOUCHER LA SURFACE VITRÉE.

• EL VIDRIO CALIENTE

CAUSARÁ QUEMADURAS.

• USTED DEBE NUNCA

TOCAR EL VIDRIO CALIENTE.

• LOS NIÑOS DEBEN NUNCA

TOCAR EL VIDRIO.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

INSTALLATEUR : Laissez cette notice avec l'appareil.

CONSOMMATEUR : Conservez cette notice pour

consultation ultérieure.

TABLE OF CONTENTS

Packaging .........................................Page 2

Introduction ......................................Page 2

General Information ..........................Page 2

Massachusetts and New York

Requirements ................................Page 4

Cold Climate Insulation .....................Page 5

Manufactured Home Requirements ..Page 5

Location ............................................Page 5

Vent Termination Clearances ............Page 6

Appliance and Vent Clearances ........Page 7

Detailed Installation Steps ................Page 8

Typical Installation Sequence ...........Page 8

Step 1. Framing ..............................Page 8

Framing Speciﬁcations ......................Page 9

Fireplace Speciﬁcations .....................Page 10

Step 2. Routing Gas Line ................Page 11

Step 3. Install the Venting System..Page 12

Step 4. Field Wiring ........................Page 13

Step 5. Optional Forced Air Blower . Page 14

Step 6. Connecting Gas Line ..........Page 14

Step 7. Outside Air Kit Installation . Page 15

Step 8. Verify Unit Operation ..........Page 16

Step 9. Install Grate, Vermiculite

Embers & Logs .................Page 16

Step 10. Installing Glass Enclosure

Panels ...............................Page 21

Step 11. Burner Adjustment .............Page 22

Step 12. Vent Operation Test and Safety

Limit Switch Operation ..................Page 23

Step 13. Hood Installation ................Page 24

Finishing Requirements ....................Page 24

Step 14. Attaching Safety-in-

Operation Warnings .....................Page 25

Gas Conversion Kits .........................Page 26

Please read and understand these

instructions before beginning your

installation.

PACKAGING LIST

The assembled vented gas ﬁreplace is pack-

aged with:

1 - One log set located in ﬁrebox area.

2 - One envelope containing the literature pack-

age which consists of the care and operation

manual, installation instructions, safety in

operation warning labels and warranty;

envelope is located in the control area.

3 - One hood located behind the top panel.

4 - One bag of decorative volcanic stone located

in the control area.

5 - One bag of glowing embers (rockwool)

located in the control area.

INTRODUCTION

The Millivolt appliances have a millivolt gas

control valve with piezo ignition system. If any

optional accessories which require electrical

power are being installed, the electrical power

must be provided at the time of appliance

installation.

The Electronic appliances have an electronic

intermittent pilot ignition system. External

electrical power is required to operate these

units.

Use Only These Approved Vent Components

- These vented gas ﬁreplaces are designed for

residential applications. They must be installed

with approved Type-B, double wall vent pipe

systems and a listed vent termination routed

to the outside atmosphere. Use only the proper

size listed below.

Required Pipe Diameter:

MPB-3328 series: Requires 4 in. (102 mm)

MPB-3530 series: Requires 5 in. (127 mm)

MPB-4035 series: Requires 5 in. (127 mm)

MPB-4540 series: Requires 6 in. (152 mm)

GENERAL INFORMATION

Children and adults should be alerted to the

hazards of high surface temperature and

should stay away to avoid burns or clothing

ignition.

Les enfants et les adultes devraient être infor-

més des dangers que posent les températures

de surface élevées et se tenir à distance aﬁn

d’éviter des brûlures ou que leurs vêtements

ne s’enﬂamment.

DO NOT ATTEMPT TO ALTER OR MODIFY

THE CONSTRUCTION OF THE APPLIANCE OR

ITS COMPONENTS. ANY MODIFICATION OR

ALTERATION MAY VOID THE WARRANTY, CER-

TIFICATION AND LISTINGS OF THIS UNIT.

WARNING

Young children should be care-

fully supervised when they are

in the same room as the appli-

ance. Toddlers, young children

and others may be susceptible

to accidental contact burns. A

physical barrier is recommended

if there are at risk individuals in

the house. To restrict access to

a ﬁreplace or stove, install an

adjustable safety gate to keep

toddlers, young children and

other at risk individuals out of

the room and away from hot

surfaces.

AVERTISSEMENT

Les jeunes enfants devraient être

surveillés étroitement lorsqu’ils

se trouvent dans la même pièce

que l’appareil. Les tout petits,

les jeunes enfants ou les adultes

peuvent subir des brûlures s’ils

viennent en contact avec la sur-

face chaude. Il est recommandé

d’installer une barrière physique

si des personnes à risques habi-

tent la maison. Pour empêcher

l’accès à un foyer ou à un poêle,

installez une barrière de sécu-

rité; cette mesure empêchera les

tout petits, les jeunes enfants et

toute autre personne à risque

d’avoir accès à la pièce et aux

surfaces chaudes.

WARNING

B-Vent appliances are not

designed to operate in negatively

pressured environments (pres-

sure within the home is less than

pressures outside). Signiﬁcant

negatively pressured environ-

ments caused by weather, home

design, or other devices may

impact the operation of these

appliances. Negative pres-

sures may result in poor ﬂame

appearance, sooting, damage to

property and/or severe personal

injury. Do not operate these

appliances in negatively pres-

sured environments.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

WARNING

Improper installation, adjust-

ment, alteration, service or

maintenance can cause injury

or property damage. Refer to

this manual. For assistance or

additional information consult

a qualified installer, service

agency or the gas supplier.

WARNING

Failure to comply with these

installation instructions will result

in an improperly installed and

operating appliance, voiding its

warranty. Any change to this appli-

ance and/or its operating controls

is dangerous.

WARNING

Clothing or other flammable

material should not be placed

on or near the appliance.

AVERTISSEMENT

On ne devrait pas placer de

vêtements ni d’autres matières

inﬂammables sur l’appareil ni à

proximité.

WARNING

Any safety screen or guard

removed for servicing the appli-

ance must be replaced prior to

operating the appliance.

AVERTISSEMENT

Tout écran ou protecteur retiré

pour permettre l’entretien de

l’appareil doit être remis en

place avant de mettre l’appareil

en marche.

WARNING

Improper installation or use of

this appliance can cause serious

injury or death from ﬁre, burns,

explosion or carbon monoxide

poisoning.

Note: Installation and repair should be done

by a qualiﬁed service person. The appliance

should be inspected before use and at least

annually by a professional service person.

More frequent cleaning may be required

due to excessive lint from carpeting, bed-

ding material, etcetera. It is imperative

that control compartments, burners and

circulating air passageways of the appliance

be kept clean.

Remarque : L’installation et la réparation

devrait être conﬁées à un technicien qualiﬁé.

L’appareil devrait faire l’objet d’une inspec-

tion par un technicien professionnel avant

d’être utilisé et au moins une fois l’an par la

suite. Des nettoyages plus fréquents peuvent

être nécessaires si les tapis, la literie, et

cetera produisent une quantité importante de

pous-sière. Il est essentiel que les comparti-

ments abritant les commandes, les brûleurs et

les conduits de circulation d’air de l’appareil

soient tenus propres.

Do not use these appliances if any part

has been under water. Immediately call a

qualiﬁed, professional service technician

to inspect the appliance and to replace any

parts of the control system and any gas

control which have been under water.

Ne pas utiliser cet appareil s’il a été plongé,

même partiellement, dans l’eau. Ap-

peler un technicien qualiﬁé pour inspecter

l’appareil et remplacer toute partie du

système de commande et toute commande

qui a été plongée dans l’eau.

Only trim kit(s) supplied by the manufacturer

shall be used in the installation of this ap-

pliance.

Seules les trousses de garniture fournies

par le fabricant doivent être utilisées pour

l’installation de cet appareil.

These appliances comply with National Safety Stan-

dards and are tested and listed by OMNI-Test

Laboratories, Inc. (Report No. 116-F-36-5) to

ANSI Z21.50 (in Canada, CSA 2.22), and CAN/

CGA-2.17-M91 in both USA and Canada, as

vented gas ﬁreplaces.

Both millivolt and electronic versions of these

appliances are listed by OMNI-Test Laborato-

ries, Inc. for installation in bedrooms in the

United States (not approved in Canada) and

in Manufactured Homes.

Misc. Codes / Standards -

The Installation must conform to local codes or,

in the absence of local codes, with the National

Fuel Gas Code, ANSI Z223.1/NFPA 54 - latest

edition (In Canada, the current CAN/CSA-B149.1

installation code).

The appliance, when installed, must be electri-

cally grounded and wired in accordance with

local codes or, in the absence of local codes,

with the National Electrical Code, ANSI/NFPA

70 - latest edition, or the Canadian Electrical

Code, CSA C22.1 - latest edition.

Provide adequate clearances around air open-

ings and adequate accessibility clearance for

service and proper operation. Never obstruct

the front openings of the appliance.

These appliances are designed to operate on

natural or propane gas only. The use of other

fuels or combination of fuels will degrade

the performance of this system and may be

dangerous.

These ﬁreplaces are designed as supplemental

heaters. Therefore, it is advisable to have an

alternate primary heat source when installed

in a dwelling.

Outside Combustion Air Hook Up -

(All manufactured home installations require

the use of an Outside Combustion Air Hook-

Up Kit)

These appliances are equipped with an integral

combustion air door and actuator arm. Com-

bustion air kits are optional. Install as shown

in Step 7 on Page 15.

Millivolt Models - The millivolt appliances are

manually controlled and feature a spark igniter

(piezo) that allows the appliance's pilot gas to

be lit without the use of matches or batteries.

This system provides continued service in the

event of a power outage.

Millivolt models come standard with a manually-

modulated gas valve; ﬂame appearance and

heat output can be controlled at the gas valve.

The BTU Input for these appliances is shown

in Table 1.

Millivolt Models with

Manually-Modulated Gas Valve

Natural Gas Propane Gas

Model Input Rate

(BTU/HR)

Input Rate

(BTU/HR)

MPB3328

13,500 to 17,500 13,500 to 17,500

MPB3530

16,000 to 20,000 16,500 to 20,000

MPB4035

24,000 to 30,000 22,300 to 28,000

MPB4540

24,750 to 31,000 23,000 to 29,000

Table 1

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Manifold Gas Supply Pressure

(all models)

Fuel # Low

(millivolt only)

High

Natural

Gas

(Lo) 2.2" WC

(0.55 kPa)

(Hi) 3.5" WC

(0.87 kPa)

Propane

(Lo) 6.3" WC

(1.57 kPa)

(Hi) 10.0" WC

(2.49 kPa)

Table 4

Inlet Gas Supply Pressure

(all models)

Fuel # Minimum Maximum

Natural Gas

5.0" WC

(1.24 kPa)

10.5" WC

(2.61 kPa)

Propane

11.0" WC

(2.74 kPa)

13.0" WC

(3.23 kPa)

Table 3

Gas Pressure - All Models

Tables 3 and 4 show the appliances' inlet and

manifold gas pressure requirements:

REQUIREMENTS FOR THE COMMON-

WEALTH OF MASSACHUSETTS

Installation of these ﬁreplaces are approved

for installation in the US state of Massachu-

setts if the following additional requirements

are met:

• Install this appliance in accordance with

Massachusetts Rules and Regulations 248

C.M.R. Sec. 5.08 2(a) through 2(e).

• Installation and repair must be doneby a

plumber or gas ﬁtter licensed in the Com-

monwealth of Massachusetts.

• The exible gaslineconnectorusedshall

not exceed 36 inches (92 centimeters) in

length.

• The individualmanualshut-off mustbea

T-handle type valve.

NEW YORK CITY, NEW YORK (MEA)

Installation of these ﬁreplaces are approved for

installation in New York City in the US state of

New York (approval no. MEA 417-05-E), if the

following additional requirements are met -

• Anoutsideairkit(FOAK-4orFOAK-4LD)

must be installed. See Figure 22 on Page

16.

Oriﬁce Sizes - Sea Level to High Altitude

(All Models)

These appliances are tested and approved for

installation at elevations of 0-4500 feet (0-1372

meters) above sea level using the standard

burner oriﬁce sizes (marked with an "*" in Table

5). For elevations above 4500 feet, contact your

gas supplier or qualiﬁed service technician.

Deration - At higher elevations, the amount

of BTU fuel value delivered must be reduced

by either:

• Usinggasthathasbeenderatedbythegas

company.

• Changingtheburneroricetoasmallersize

as regulated by the local authorities having

jurisdiction and by the (USA) National Fuel

Gas Code NFPA 54/ANSI Z223.1 - latest

edition or, in Canada, the CAN/CSA-B149.1

codes - latest edition.

Install the appliance according to the regulations

of the local authorities having jurisdiction and,

in the USA, the National Fuel Gas Code NFPA

54 / ANSI Z223.1 - latest edition or, in Canada,

the CAN/CSA-B149.1 - latest edition.

NOTE: Flame appearance will diminish 4% per

thousand feet.

Gas Valve Diagrams

See Figure 1 for Millivolt models and Figure 2

For Electronic Models.

HTPTHTPT

OUT

Manifold Pressure Tap

Inlet Pressure Tap

Pilot Adjustment

Screw

HI/LO Variable

Flame Height

Adjustment

Main Gas

Control Knob

OFF/PILOT/ON

Figure 1 - SIT Millivolt Gas Valve

Figure 2 - Honeywell Electronic Gas Valve

FFO

LORTNOC

GI N TI ER

Manifold Pressure

Port

ON / OFF Switch

Inlet

Pressure

Port

Electronic Gas

Control Valve

Test gauge connections are provided on

the front of the millivolt gas control valve,

identiﬁed IN for the inlet and OUT for the

manifold side. A 1/8" NPT Test gauge connec-

tion is provided at the inlet and outlet side of

the electronic gas control valve adjacent to the

outlet to the main burner.

Propane tanks are at pressures that will cause

damage to valve components. Verify that the

tanks have step down regulators to reduce the

pressure to safe levels.

These appliances must be isolated from the

gas supply piping system (by closing their

individual manual shut-off valve) during any

pressure testing of the gas supply piping

system at test pressures equal to or less

than 1/2 psig (3.5 kPa).

These appliances and their individual shut-off

valves must be disconnected from the gas

supply piping system during any pressure

testing of that system at pressures greater

than 1/2 psig (3.5 kPa).

These appliances must not be connected to a

chimney or ﬂue serving a separate solid fuel

burning appliance.

Electronic Models with

Fixed-Rate Gas Valve

Natural Gas Propane Gas

Model Input Rate

(BTU/HR)

Input Rate

(BTU/HR)

MPB3328

17,500 17,500

MPB3530

20,000 20,000

MPB4035

30,000 28,000

MPB4540

31,000 29,000

Table 2

Electronic Models - These electronic appliances

have a ﬁxed rate gas valve and an electronic

intermittent pilot ignition system. External

electrical power is required to operate these

units. The BTU Input for these appliances is

shown in Table 2.

Burner Oriﬁce Sizes

Elevation 0-4500 feet ( 0-1372 meters)

Model

Series

Nat.Gas

drill size (inches)

Propane

drill size (inches)

MPB-3328 #47 (.0785") *

39L66 •

#1.2m (.048")*

99K78 •

MPB-3530 #44 (.086") *

60J80 •

#55 (.052") *

19L52 •

MPB-4035 #37 (.104") *

24M10 •

1/16"

(.0625") *

21L01 •

MPB-4540 #36 (.1065") *

18L40 •

#52

(.0635") *

37G00 •

Table 5

* Standard size installed at factory

• Part /Cat. Number

Figure 3 - Typical Installations

Note: When the unit is installed with one side ﬂush

with a wall, the wall on the other side of the unit must

not extend beyond the front edge of the unit.

COLD CLIMATE INSULATION

For cold climate installations, seal all cracks

around your appliance with noncombustible

material and wherever cold air could enter

the room. It is especially important to insulate

outside chase cavity between studs and under

ﬂoor on which appliance rests, if ﬂoor is above

ground level. Gas line holes and other open-

ings should be caulked or stuffed with unfaced

ﬁberglass insulation.

If the ﬁreplace is being installed on a cement

slab in cold climates, a sheet of plywood or

other raised platform can be placed underneath

to prevent cold transfer to the ﬁreplace and into

the room. It also helps to sheetrock inside

surfaces and tape for maximum air tightness

and caulk ﬁrestops.

MANUFACTURED HOME

REQUIREMENTS

This appliance may be installed in an aftermarket

permanently located, manufactured home and

must be installed in accordance with the manu-

facturer's instructions and the Manufactured

Home Construction and Safety Standard, Title

24 CFR, Part 3280, in the United States, or the

Standard for Installation in Mobile Homes, CAN/

CSA Z240 MH Series, in Canada.

Cet appareil peut être installé cómme du matéri-

el d'origine dans une maison préfabriquée (É.U.

seulement) ou mobile et doit être installé selon

les instructions du fabricant et conformément

à la norme Manufactured Home Constructions

and Safety, Title 24 CFR, Part 3200 aux Unis ou

à la norme Can/CSA-Z240 Série MM, Maisons

mobiles au Canada.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certiﬁed kit is used.

Cet appareil doit être utilisé uniquement avec le

type de gaz indiqué sur la plaque signalétique.

Cet appareil ne peut être converti à d'autres gaz,

sauf si une trousse de conversion est utilisée.

CAUTION: Ensure that the cross mem-

bers are not cut or weakened during

installation. The structural integrity of

the manufactured home ﬂoor, wall, and

ceiling / roof must be maintained.

CAUTION: This appliance must be ground-

ed to the chassis of the manufactured

home in accordance with local codes or

in the absence of local codes, with the

National Electrical Code ANSI / NFPA 70

- latest edition or the Canadian Electrical

Code CSA C22.1 - latest edition.

Notes:

• An Outside Combustion Air Hook-Up Kit

must be installed (see Step 7, Page 15).

LOCATION

In selecting the location, the aesthetic and

functional use of the appliance are primary

concerns. However, vent system routing to

the exterior and access to the fuel supply are

also important.

Due to high temperatures, the appliance

should be located out of trafﬁc and away from

furniture and draperies (Figure 3).

En raison des températures élevées, l’appareil

devrait être installé dans un endroit où il y a

peu de circulation et loin du mobilier et des

tentures (Figure 3).

The location should also be free of electrical,

plumbing or other heating/air conditioning

ducting.

Be aware that this is a heat producing ap-

pliance. Objects placed above the unit are

exposed to elevated temperatures.

Do not insulate the space between the appli-

ance and the area above it.

The appliance should be mounted on a fully

supported base extending the full width and

depth of the unit. The appliance may be located

on or near conventional construction materials.

However, if installed on combustible materials,

such as carpeting, vinyl tile, etc., a metal or

wood barrier covering the entire bottom surface

must be used.

Offset

Venting

Vertical

Venting

Shown with Outside Air Kit

installed (model FOAK-4 or

FOAK-4LD)

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

VENT TERMINATION CLEARANCES

Gas Vent Rule - Gas vent caps are not per-

mitted within 8 feet (2.4 mm) of a vertical wall

or similar obstruction. Gas vent caps that are

located 8' or more from a portion of a building

which extends at an angle greater than 45°

upward from the horizontal may terminate in

accordance with (Figure 4 ), provided that in no

case shall any discharge opening on the cap be

less than 2' (610 mm) horizontally from the roof

surface (National Fuel Gas Code ANSI Z223.1

(NFPA 54) 7.6.2) (CAN/CGA B149).

Multiple Terminations

These appliances may vent adjacent to and at

the same level with any other gas appliances

(including direct-vent appliances) provided that

there is at least 2 ft. (0.6m) between the proximal

edges of the vent caps. These appliances may

be vented adjacent to a chimney vent servicing

a solid fuel ﬁreplace provided the B-vent cap

is at least 2 ft. (0.6m) away from the nearest

point of the chimney opening.

Termination Heights For Vents

Above Flat Or Sloped Roofs

Ref. NFPA 54 / ANSI Z223.1, 7.6

Roof Pitch Feet Meters

Flat to 6/12 1.0 0.3

6/12 to 7/12 1.25 0.38

7/12 to 8/12 1.5 0.46

8/12 to 9/12 2.0 0.61

9/12 to 10/12 2.5 0.76

10/12 to 11/12 3.25 0.99

11/12 to 12/12 4.0 1.22

12/12 to 14/12 5.0 1.52

14/12 to 16/12 6.0 1.83

16/12 to 18/12 7.0 2.13

18/12 to 20/12 7.5 2.29

20/12 to 21/12 8.0 2.44

Figure 4 - Vertical Vent Termination Clearances

Roof Pitch is X/12

Minimum Height from Roof to

Lowest Discharge Opening

1“ (25 mm)

Minimum

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Hearth Extension - A hearth extension is not required with this appliance.

If a hearth extension is used, do not block the control compartment access

panel. Any hearth extension used is for appearance only and does not have

to conform to standard hearth extension installation requirements.

Wall Finishes / Surrounds / Mantels

Note: Combustible wall ﬁnish materials and/or surround materials must

not be allowed to encroach the area deﬁned by the appliance top spacers.

Never allow combustible materials to be positioned in front of or overlap-

ping the appliance front face and top spacers. See Figure 38.

Non-combustible materials, such as surrounds and other appliance trim,

may be installed on the appliance front face with these exceptions: The

material must NOT cover any portion of the glass or louvers.

Vertical installation clearances to combustible mantels vary according to

the depth of the mantel (refer to Figure 5). Mantels constructed of non-

combustible materials may be installed at any height above the appliance

opening; however, do not allow anything to hang below the hood.

These instructions should be used as a guideline and do not supersede

local codes in any way.

MINIMUM CLEARANCES

Inches (millimeters)

Back 1/2 (13)

Sides 1/2 (13)

Top Spacers 0 (0)

Floor 0 (0)

Bottom of Appliance

To Ceiling

64 (1626)

Vent 1 (25.4)

SERVICE CLEARANCES

Feet (meters)

Front 3 ft. (0.9 m)

Table 6

0” Clearance

to Combustible

Side Wall

Ceiling

64 in.

(1626 mm)

Bottom of Fireplace

Figure 6

*Note: See Figures 7 and 8 on Page 8 for clearance requirements to

the nailing ﬂange located at each side of the unit and any screw heads

adjacent to it.

MINIMUM CLEARANCES TO COMBUSTIBLES

Appliance And Vent Clearances

Maintain clearances from appliance to combustible materials as detailed

in Table 6 with the following exception: When the unit is installed with

one side ﬂush with a wall, the wall on the other side of the unit must

not extend beyond the front edge of the unit. In addition, when the unit

is recessed, the side walls surrounding the unit must not extend beyond

the front edge of the unit (see Figure 3).

Figure 5 - Minimum Mantel Clearances

12 (305) MANTEL

10 (254) MANTEL

8 (203) MANTEL

6 (152) MANTEL

4 (102) MANTEL

(102)

(356)

(305)

(254)

2 (51) MANTEL

TOP OF

APPLIANCE

(152)

NOTE - Hood shown as positioned

in louvered front model. The hood

position in the flush faced front model

is lower than shown.

(203)

MANTEL CLEARANCES

Inches (mm)

*Note - The side walls of mantels may protrude

beyond the front face of the fireplace a maximum

of 5 inches (127mm) at 0 inch clearance to the

sides of the fireplace.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Step 7. (Page 15) Outside Air Kit Installa-

tion.

Step 8. (Page 16) Verify appliance opera-

tion.

Step 9. (Page 16) Install grate, vermiculite,

embers and logs.

Step 10. (Page 21) Installation/Removal of

glass enclosure panels.

Step 11. (Page 22) Adjust burner primary

air shutter to achieve proper ﬂame

appearance.

Step 12. (Page 23) Vent operation test and

(safety limit) switch operation.

Step 13. (Page 24) Install the decorative trims

and hoods.

Step 14. (Page 25) Attach Safety in Operation

Warnings.

Step 1. FRAMING

Frame these appliances as illustrated in Figure

9. All framing details must allow for a minimum

clearance to combustible framing members as

shown in Table 6 on Page 7.

If the appliance is to be elevated above ﬂoor

level, a solid continuous platform must be

constructed below the appliance.

Note: The framed depth, 16 in. (406 mm) from

a framed wall, must always be measured from

a ﬁnished surface. If a wall covering such as

drywall is to be attached to the rear wall, then

the 16 in. (406 mm) must be measured from

the drywall surface. It is important that this

dimension be exact.

Headers may be in direct contact with the

appliance top spacers but must not be sup-

ported by them or notched to ﬁt around them.

All construction above the appliance must be

self-supporting, DO NOT use the appliance for

structural support.

Pre-installation Notes

The ﬁreplace may be positioned and then the

framing built around it, or the framing may be

constructed and the ﬁreplace positioned into

the opening.

Usually, no special ﬂoor support is needed for

the ﬁreplace, however, to be certain:

1. Estimate the total weight of the ﬁreplace

system and surround materials such as

brick, stone, etc., to be installed.

2. Measure the square footage of the ﬂoor space

to be occupied by the system, surrounds and

hearth extensions.

3. Note the ﬂoor construction, i.e. 2 x 6’s, 2 x

8’s or 2 x 10’s, single or double joists, type

and thickness of ﬂoor boards.

4. Use this information and consult your local

building code to determine if you need ad-

ditional support.

DETAILED INSTALLATION STEPS

The appliance is shipped with all gas controls

and components installed and pre-wired.

1. Remove the shipping carton. Remove the

shipping pad, exposing the front glass

door.

2. Open the two latches (located under the ﬁre-

box ﬂoor) securing the glass door. Remove

the door by tilting it outward at the bottom

and lifting it up. Set the door aside protecting

it from inadvertent damage. See Removing

Glass Enclosure Panel on Page 21.

TYPICAL INSTALLATION SEQUENCE

The typical sequence of installation is outlined

below. However, each installation is unique

and may result in variations to the steps

described.

See the Page numbers references in the follow-

ing steps for detailed procedures.

Step 1. (Page 8) - Construct the appliance

framing. Position the appliance

within the framing and secure with

nailing ﬂanges.

Step 2. (Page 11) Route gas supply line to

appliance location.

Step 3. ( Page 12) Install the vent system and

exterior termination.

Step 4. (Page 13) Field Wiring

a. Millivolt Appliances – Install the

OFF/ON burner control switch.

b. Electronic Appliances – Connect

120 VAC electrical power to the appli-

ance receptacle.

Step 5. (Page 14) Install the optional

blower.

Step 6. (Page 14) Make connection to gas

supply.

WARNING

Failure to position the parts in

accordance with these diagrams

or failure to use only parts speciﬁ-

cally approved with this appliance

may result in property damage or

personal injury.

AVERTISSEMENT

Risque de dommages ou de

blessures si les pièces ne sont

pas installées conformément à

ces schémas et ou si des pièces

autres que celles spéciﬁquement

approuvées avec cet appareil sont

utilisées.

Figure 8

Figure 7

Note:

Some units only have one anchor tab on each side.

Note: The nailing flanges, combustible members

and screw heads located in areas directly adjacent

to the nailing flanges, are EXEMPT from the 1/2”

clearance to combustible requirements for the

firebox outer wrapper. Combustible framing may be

in direct contact with the nailing flanges and may

be located closer than 1/2” from screw heads and

the firebox wrapper in areas adjacent to the nailing

flanges. Frame the opening to the exact dimensions

specified in the framing details of this manual.

Side

Framing

Unit Nailing Flange

(No clearance to

combustible

framing is required)

Left Side Front Corner of Fireplace Shown

(Right Side Requirements the Same)

Unit Being Secured By Its Nailing Flanges

To The Framing

Anchor

Ta b

Side Nailing Flanges

The ﬁreplace should be secured to the side

framing members using the unit's nailing

ﬂanges - two at the top and bottom on each

side of the ﬁreplace front. See Figure 7. Use

8d nails or their equivalent.

Floor Nailing Tabs

Fireplace may be anchored to ﬂoor. Bend down

two anchor tabs (one on each side) located

at the base of the ﬁreplace and secure to the

ﬂoor by nailing with 8d nails or equivalent

(Figure 8).

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

FRAMING SPECIFICATIONS

Note: All framing dimensions calculated for 1/2" dry wall at the appliance face. If sheathing the chase or ﬁnishing with other thickness

materials, calculations will need to be made.

* Outside air kit - FOAK (without adapter). See Figure 22 on Page 16.

*Optional FOAK

Outside

Air Kit

Outside Chase

Back Wall of Chase/Enclosure

Including Finishing Materials

if any

Rough Framing Face

(Unfinished Shown)

Header

Fireplace Framing

Inside Chase

Back Wall of Chase/Enclosure

Including Finishing Materials

if any

Rough

Framing Face

(Unfinished Shown)

H H

Corner Installation

Back Wall of Chase/Enclosure

Including Finishing Materials

if any

Rough

Framing Face

(Unfinished Shown)

.oNledoM

tinU

eziS

gnimarF

eziS

BCDEFGHJ K

.ni538/1-534/1-534/1-918/5-91752/1-4/3-82614 61/9-68/5-04

mm29859859838489406410376042017612301

.ni8/1-044/1-044/1-04428/5-4261/31-1661/1-03614 61/9-623/11-34

mm91012201220101652607519776042017611011

.ni8/1-044/1-544/1-04428/5-928/3-6661/3-33614 61/9-661/51-64

mm64119411220101625768613486042017612911

MPB3328

MPB3530

MPB4035

MPB4540

in.

845

842

33-1/4

845

33-1/4

546

21-1/2

286

11-1/4

1232

48-1/2

616

24-1/4

330

102

103

4-1/16

872

34-5/1633-1/8

12-3/4

14-11/16

17-3/16

437

373

324

1146

45-1/8

24-7/8

29-7/8

34-7/8

886

759

632

30-11/16

7-1/16

179

Figure 9

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Top View

FRAMING

SPACERS

(Top and Sides

and Rear)

Front View

3 (76)

Flue Outlet For B-Vent Connection

OPTIONAL ELECTRICAL

INLET KNOCKOUT

REQUIRING A FIELD

PROVIDED JUNCTION

BOX (Either Side)

GAS INLET

(Either Side

and bottom)

NOTE - Hood shown

as positioned

in louvered

front model.

ELECTRICAL INLET

2-3/4 x 2 (70 x 51) COVER

PLATE with KNOCKOUT)

1/2 (13)

3 (76)

1³⁄₈

(35)

(140)

5-1/2

9-3/8

(238)

(53)

Right Side View

(140)

5-1/2

9-3/8

(238)

1-3/8

(35)

Left Side View

GAS INLET

(See Also

Right Side View)

ELECTRICAL INLET

(See Also

Right Side View)

(76)

OUTSIDE AIR

SHUTTER

8-15/16

(227)

7-3/8

(187)

ELECTRICAL

INLET

(Optional)

.oNledoMABCDEFG

.ni538/1-8/1-23912/1-92538/1-8/-61/7-258-3/4

330

406

mm298618384947298236613721 222

.ni8/1-048/1-73422/1-438/1-048/7-92161/51-458-3/4

mm91013490166789101957973721

.ni8/1-048/1-73422/1-938/1-548/7-4361/7-7168-3/4

mm641134901630016411688344251 222

MPB3328

MPB3530

MPB4035

MPB4540

in.

33-1/8

841 432

765 841

699

21-1/2

33-1/8

546

102273

27-1/2

1730-1/8

24-7/8

621

12-7/16

10-3/4

6-1/2

165

FIREPLACE SPECIFICATIONS

Figure 10

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Step 2. ROUTE GAS SUPPLY LINE

Route a 1/2" (13 mm) gas line as shown in

Figure 11. Gas lines must be routed, con-

structed and made of materials that are in strict

accordance with local codes and regulations.

The appliance, as set up at the factory, is best

suited for use with a gas line routed from the

right side. The gas line may however be alter-

nately routed from the left side. All appliances

are factory-equipped with a ﬂexible gas line

connector and 1/2 inch shutoff valve. (See

Step 6 on Page 14).

Also see

Figure 10

6 1/2"

(152 mm)

(76 mm)

Figure 11 - Route Gas Line

Right Side Front

Corner of Fireplace

Framing

Schedule 40 (black iron) Pipe

Inside Diameter (Inches)

Schedule 40 Pipe

Length (feet)

Natural

Gas

Propane

Gas

0-10 1/2 3/8

10-40 1/2 1/2

40-100 1/2 1/2

100-150 3/4 1/2

150-200 3/4 1/2

Table 7

Proper Sizing of Gas Line

Properly size and route the gas supply line

from the supply regulator to the area where

the appliance is to be installed per require-

ments outlined in the National Fuel Gas Code,

NFPA 54 - latest edition (USA) or B149 - latest

edition (Canada).

Notes:

• All appliances are factory-equipped with a

ﬂexible gas line connector and 1/2 inch shutoff

valve (see Figure 20 on Page 15).

• SeeMassachusetts Requirements on Page 4

for additional requirements for installations in

the state of Massachusetts in the USA.

• ThegassupplylineshouldNotbeconnected

to the appliance until Step 6 (Page 14).

• Apipejointcompoundratedforgasshouldbe

used on the threaded joints. Ensure propane

resistant compounds are used in propane

applications. Be very careful that the pipe

compound does not get inside the pipe.

• Itisrecommendedtoinstallasedimenttrap

in the supply line as close as possible to the

appliance (see Figure 20, Page 15). Appliances

using propane should have a sediment trap at

the base of the tank.

• Checkwithlocalbuildingofcialforlocalcode

requirements (i.e. are below grade penetrations

of the gas line allowed?, etc).

IMPORTANT: If propane is used, be aware that

if tank size is too small (i.e. under 100-lbs, if

this is the only gas appliance in the dwelling.

Ref. NPFA 58), there may be loss of pressure,

resulting in insufﬁcient fuel delivery (which

can result in sooting, severe delayed ignition

or other malfunctions). Any damage resulting

from an improper installation, such as this, is

not covered under the limited warranty.

Never use galvanized or plastic pipe. Refer

to Table 7 for proper sizing of the gas supply

line, if black iron pipe is being used. Gas lines

must be routed, constructed and made of

materials that are in strict accordance with

local codes and regulations. We recommend

that a qualiﬁed individual such as a plumber

or gas ﬁtter be hired to correctly size and route

the gas supply line to the appliance. Installing

a gas supply line from the fuel supply to the

appliance involves numerous considerations of

materials, protection, sizing, locations, controls,

pressure, sediment, and more. Certainly no one

unfamiliar and unqualiﬁed should attempt sizing

or installing gas piping.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 13

Figure 12

Type B-Vent - 4 in. (102 mm) for MPB 3328 Models,

5 in. (127 mm) for MPB 3530 / 4035 Models or 6 in.

(153 mm) for MPB 4540 Models

Securing

Screws

Flue Outlet

Collar

USE ONLY APPROVED B-VENT DIAMETER

MPB-3328, MPB-3530, MPB-4035 and MPB-

4540 series ﬁreplaces must be vertically

vented using listed type-B, double-walled

vent pipe with the proper diameter as listed

below and a listed vent termination.

Required Pipe Diameter:

MPB-3328 series: Requires 4 in. (102 mm)

MPB-3530 series: Requires 5 in. (127 mm)

MPB-4035 series: Requires 5 in. (127 mm)

MPB-4540 series: Requires 6 in. (152 mm)

Back View

Of Appliance

10 ft.

Minimum

Back View

Of Appliance

*12 ft. Min.

**15 ft. Min.

*with an offset up to 45 degrees

** with an offset greater than 45

degrees and up to 60 degrees

Vertical

Installations

Back View

Of Appliance

10 ft.

Minimum

Back View

Of Appliance

*12 ft. Min.

**15 ft. Min.

*with an offset up to 45 degrees

** with an offset greater than 45

degrees and up to 60 degrees

Offset

Installations

The maximum overall height of the vent system

and appliance should not exceed 40 feet.

Note: Refer to the vent manufacturers instal-

lation instructions for variations of venting

techniques. If common venting of several units

is contemplated, it should be discussed with an

architect and the local Building Department.

Do not place insulation materials within 1 in.

of the gas vent system.

CAUTION

This appliance cannot be vented

horizontally.

Step 3. INSTALL THE VENT SYSTEM &

EXTERIOR TERMINATION:

General Information

These instructions should be used as a

guideline and do not supersede local codes

in any way. Install venting according to local

codes, these instructions, the current National

Fuel Gas Code (ANSI-Z223.1) in the USA or

the current standards of CAN/CSA-B149.1

in Canada.

Ensure clearances are in accordance with

local installation codes and the requirements

of the gas supplier.

Dégagement conforme aux codes d'installation

locaux et aux exigences du foumisseunde

gaz.

Use only approved venting components.

See Approved Vent Components on

Page 2.

These ﬁreplaces must be vented directly

to the outside.

Slip the ﬁrst section of B-Vent over the ﬁreplace

ﬂue outlet and secure with four sheetmetal

screws (# 8 or larger), and install the remainder

of the B-Vent to the outside. Minimum overall

height of the vent system and appliance must

be 10' (2.54 m) vertical - no offset (see Figure

13); or 12' (3.7 m) when an offset up to 45

degrees from the vertical is used: or 15' (4.6

m) when an offset is greater than 45 degrees

and up to 60 degrees.

The offset may start at the ﬁreplace ﬂue collar

(see Figure 13). The maximum overall height

of the vent system and appliance should not

exceed 40 feet.

Install the B-vent system in accordance with

the vent manufacturer's instructions.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

A. SIT Millivolt Wiring

(See Figure 14) –

1. Select any of the following optional controls:

appliance-mounted (rocker switch) or wall-

mounted switch, thermostat, or one of the

optional remote control kits. If appliance-

mounted ON/OFF control is selected mount

it in the gas valve mounting bracket.

2. If wall-mounted ON/OFF control switch or

thermostat is selected mount it in a conve-

nient location on a wall near the ﬁreplace.

3. Wire the control switch within the millivolt

control circuit using the 15 feet of 2 conduc-

tor wire supplied with the unit . Caution: do

not connect the optional wall switch to a

120V power supply.

4. Alternatively, the appliance may be operated

without the use of the controls indicated

in Instruction #1, solely by manipulating

the gas valve control knob. In order to use

this method, twist the free ends of the two

conductor wire (located in the lower com-

partment of the unit) together as shown in

Figure 14.

Note: The supplied 15 feet of 2 conductor wire

has one end of each conductor connected to

the gas valve circuit and the other end of each

conductor placed inside the control compart-

ment.

Figure 14

SIT Millivolt Wiring Diagram

If any of the original wire as supplied must be replaced,

it must be replaced with Type AWM105°C– 18 GA. wire.

Thermopile

*TWIST WIRES “A” AND “B” TOGETHER TO OPERATE UNIT

SOLELY BY MANIPULATING THE GAS VALVE CONTROL KNOB;

OR CONNECT WIRES TO OPTIONAL ON/OFF SWITCH OR WALL

SWITCH OR THERMOSTAT OR REMOTE CONTROL RECEIVER

TO OPERATE UNIT.

*OPTIONAL ON/OFF SWITCH,

WALL SWITCH, THERMOSTAT

OR REMOTE CONTROL RECEIVER

HCTIWS TIMIL

Schematic Representation Only

Step 4. FIELD WIRING

CAUTION

Ground supply lead must be con-

nected to the wire attached to the

green ground screw located on

the outlet box. See

Figures 17 or

18. Failure to do so will result in a

potential safety hazard. The appli-

ance must be electrically grounded

in accordance with local codes or,

in the absence of local codes, the

National Electrical Code, ANSI/

NFPA 70-latest edition.

(In Canada,

the current CSA C22-1 Canadian Elec-

trical Code).

CAUTION: Label all wires prior to disconnec-

tion when servicing controls. Wiring errors can

cause improper and dangerous operation.

ATTENTION: Au moment de l'entretien des

commandes, étiquetez tous les fils avant de

les débrancher. Des erreurs de cáblage peu-

vent entraîner un fonctionnement inadéquat

et dangereux.

Verify proper operation after servicing.

S'assurer que l'appareil fonctionne adé-

quatement une fois l'entretien terminé.

CAUTION: DO NOT CONNECT OPTIONAL CON-

TROL SWITCH TO 120 V POWER SUPPLY.

CAUTION: REMOVE THE CARTON SUPPORT

FROM THE CONTROL COMPARTMENT BEFORE

OPERATING THE APPLIANCE.

CAUTION: ENSURE THAT WIRES ARE POSI-

TIONED AWAY FROM HOT SURFACES AND

SHARP EDGES.

Refer to Section A for millivolt appliances and

Section B for electronic appliances. The gas

valve is set in place and pre-wired at the factory

on both models.

B. Electronic Wiring (See Figures 17 or 18) –

Note: The electronic appliance must be con-

nected to the main power supply.

A junction box is located at the rear of the con-

trol compartment on either side of the cabinet.

The junction box on the right side contains a

factory installed and wired outlet box (duplex

receptacle). Also, an optional ﬁeld-provided

junction box with receptacle may be installed at

the front of the control compartment on either

side of the cabinet. See Figure 15. It will be

held in place by a conduit ﬁtting and locknut

(ﬁeld-provided).

1. Route a 3-wire 120Vac 60Hz 1ph power

supply to the appliance junction box.

Figure 15

See Figure 10 on Page 10

for Optional Electrical Inlet

Knockout Location.

* Field-Provided

Junction Box and

Duplex Receptacle

* Narrow (2-1/8 Inch Wide)

J-Box Required

Optional J-Box/Outlet Box

(Left Side Shown)

BLOWER CONTROL CIRCUIT WIRING

120V, 60HZ, 1PH

Factory Wired

Ground

Field Wired

Junction Box

Tab Intact

Tab

Broken

Plug blower

into this

receptacle

neerG - dnuorG

* Wall-mounted

ON/ OFF Blower

Switch or Variable

Speed Control Switch.

Blower

etihW - lar

ueN

120 VAC - Black

Green

Ground

Screw

White

Green

Neutral

Side of

Receptacle

Hot

Side of

Receptacle

Red

Black

Figure 16: Junction Box Wiring

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 17

Figure 18

1. If any of the original wire as supplied must be replaced,

1. it must be replaced with Type AWM 105°C – 18 GA. wire.

2. 120V, 60Hz – Less than 3 amps.

Junction Box

Transf.

120 V.

24 V

Factory Wired Field Wired

Electronic Wiring Diagram (Honeywell)

Showing the Blower Wiring for the Optional

FBK-100 and FBK-200 Kits

OPT

BLOWER

*OPTIONAL

ACCESSORY

SWITCH

120

VAC.

Gas Valve

IGNITER

PILOT

ASSEMBLY

Break Off

Tab

*Blower speed control switch is provided in FBK200 blower kit.

Outlet Box

Green Ground

Screw

Hot side of Outlet

Schematic Representation Only

**ON/OFF Switch (Integral

with Gas Valve)

**Leave the ON/OFF switch, which is integral

with the gas valve, in the ON position.

Red

pigtail

Black

pigtail

White Wire

to Opposite

Side

LIMIT SWITCH

OPTIONAL WALL SWITCH

OR OPTIONAL THERMOSTA

T OR

OPTIONAL REMOTE RECEIVER

BK BK

1. If any of the original wire as supplied must be replaced,

1. it must be replaced with Type AWM 105°C – 18 GA. wire.

2. 120V, 60Hz – Less than 3 amps.

Junction Box

Transf.

120 V.

24 V

Factory Wired Field Wired

Electronic Wiring Diagram (Honeywell)

Showing the Blower Wiring for the Optional

FBK-250 Kits

OPT

BLOWER

120

VAC.

Gas Valve

IGNITER

PILOT

ASSEMBLY

Outlet Box Green

Ground Screw

Hot side of Outlet

Schematic Representation Only

*ON/OFF Switch (Integral

with Gas Valve)

White Wire

To Opposite

Side

Optional FBK-250

Module

*Leave the ON/OFF switch, which is integral

with the gas valve, in the ON position.

OPTIONAL ON/OFF SWITCH,

WALL SWITCH, THERMOSTAT

OR REMOTE CONTROL RECEIVER

LIMIT SWITCH

Figure 19

OPENING CONTROL

COMPARTMENT DOOR

Control

Valve

Lower Control

Compartment

Door

Open the lower panel or louver assembly by

pushing in the right side of the panel or louver

assembly and then lowering it forward and

down.

Step 6. CONNECTING GAS LINE

All codes require a shut-off valve mounted

in the supply line. The orientation of the

shut-off valve should face the front. Figure

20 illustrates two methods for connecting the

gas supply. A Sediment Trap is recommended

to prevent moisture and debris in gas line from

damaging the valve.

The ﬂex-line method is acceptable in the U.S.A.

where local codes permit, however, Canadian

requirements vary depending on locality. Instal-

lation must be in compliance with local codes.

These appliances are equipped with a gas ﬂex-

line for use in connecting the unit to the gas line.

See Figure 20 for ﬂex-line description. The

ﬂex-line is rated for both natural and propane

gas. A manual shut off valve is also provided

with the ﬂex-line.

The gas control valve is located in the lower

control compartment.

To access the valve open the lower control

compartment door (see Figure 19).

The millivolt control valve has a 3/8" (10 mm)

NPT thread inlet port. The electronic control

valve has a 1/2" (13 mm) NPT thread inlet

port and is ﬁtted with a 1/2" x 3/8" (13 mm x

10 mm) NPT ﬁtting.

2. If the factory-provided outlet/junction box at

the right rear of the ﬁreplace is being used,

remove the outlet box from the junction box

by removing two screws.

3. Connect the power supply wires (includ-

ing the ground supply wire) as shown in

Figures 17 and 18. (If the ﬁeld-provided

J-box/outlet box is being used, all of the

outlet box wiring must be ﬁeld-provided).

4. Locate and install a low voltage (24V)

wall-mounted switch or thermostat (both

ﬁeld-provided) in the desired location.

5. Connect the low voltage wire, located in

the lower control compartment, to the wall-

mounted switch or thermostat.

Note: The supplied 15 feet of 2 conductor wire

has one end of each conductor connected

to the gas valve circuit and the other end of

each conductor placed inside the control

compartment.

6. Insert the control circuit plug into the un-

switched receptacle of the outlet box.

7. After wiring is complete, mount the outlet

box to the J-Box.

Note: The gas valve-mounted ON/OFF switch

is shown in Figures 17 and 18. It is integral

with the gas valve and should be set to the

ON position.

Step. 5 WIRING - OPTIONAL FORCED

AIR BLOWER KIT

FBK-100, FBK-200 and FBK250 Kits

(See Figure 17 for FBK-100, FBK-200 and

Figure 18 for FBK-250 wiring) -

An electrical outlet box (receptacle) is factory

-provided for the installation of the FBK-100,

FBK-200 and FBK-250 forced air blower kits.

(An optional ﬁeld-provided outletbox/J-Box

may also be used. Electrical power must be

connected to either of these receptacles in order

to operate these blowers. Install the blower

kits according to the installation instructions

provided with the kits.

Note: The tab connecting the receptacles of

the outlet box must be broken in FBK-100 and

FBK-200 blower kit applications. See Figure

16 on page 13.

Secure all joints tightly using appropriate

tools and sealing compounds (ensure propane

resistant compounds are used in propane ap-

plications). It is recommended to seal around

the gas line to prevent cold air leakage.

Acquire the shut-off valve and gas lex line and

pull the assembly forward out of the compart-

ment. Separate the shut-off valve from the gas

ﬂex-line. Determine the length of pipe needed

to route the gas line from the last ﬁtting (shown

in Figure 20 on Page 15) to a point within the

control compartment that will allow the shut-

off valve to be easily attached by hand to the

gas ﬂex-line.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Using pipe-dressing materials appropriate for

the gas type, securely afﬁx the shut-off valve

to this determined pipe length at a convenient

location outside of the appliance lower control

compartment.

TEST ALL CONNECTIONS FOR GAS LEAKS

(FACTORY AND FIELD):

Figure 21

Operate the actuator through several cycles

including the closed position. Ensuring proper

operation and freedom of movement. Return

the actuator arm to the closed position.

Outside Air Control Lever

and Securing Screw Location

on Left Side of Cabinet in Lower Control

Compartment Area

Outside Air Control Lever

Securing screw

Air Shutter in Closed Position

Outside Air Control Lever

Securing Screw Removed

Air Shutter in Open Position

Note: The gas supply line

must be installed in accor-

dance with building codes

by a qualiﬁed installer

approved and/or licensed

as required by the locality.

In the Commonwealth of

Massachusetts, installa-

tion must be performed

by a licensed plumber or

gas ﬁtter.

Gas

Valve

3/8" NPT x

Flare Fitting

3/8" Flex Tubing

3/8" Nipple

3/8" Union

3/8" Close

Nipple

3/8" Shut-off Valve

1/2" x 3/8"

Reducer

Gas

Stub

1/2" x 3/8" Flare

Shut-off Valve

Gas Solid Line Connector

Gas Flex Line Connector

*Sediment

Trap

Min

Figure 20 - GAS CONNECTION

Outside air drawn into the ﬁreplace supplies

air to the ﬁre for combustion. Only one outside

air duct is necessary, if installed. See Figure

3 on Page 5 and Figure 22 on Page 16 for the

location of the unit's outside air inlet.

If additional length of duct is necessary, pur-

chase locally available U.L. Class 0 or Class 1

metallic ducting. The duct may extend up to 50'

(15.24 m) in any direction.

Note: When installing the air duct vertically, DO

NOT terminate the duct closer than 3' below

the chimney top.

Outside combustion air ducting may be run

upwards or vertically through framing and ceil-

ing joists, with the hood installed through an

outside wall and 3' (1 m) below the termination.

Ducting may also be run downward through

ﬂoor joists and under the home to a ventilated

crawlspace not considered part of the living

area of the home.

Note: Do not terminate outside air kit in attic

space under any circumstances.

Turn on gas supply and test for gas leaks us-

ing Turn on gas supply and test for gas leaks,

using a gas leak test solution (also referred to

as bubble leak solution).

Note: Using a soapy water solution is an effec-

tive leak test solution but it is not recommended,

because the soap residue that is left on the pipes/

ﬁttings can result in corrosion over time.

A. Light the appliance (refer to the lighting

instructions label in the control compartment

or in the Care and Operation Instructions

manual).

B. Brush all joints and connections with the gas

leak test solution to check for leaks. If bubbles

are formed, or gas odor is detected, turn the

gas control knob (off/pilot/on) to the “OFF”

position. Either tighten or refasten the leaking

connection, then retest as described above.

C. When the gas lines are tested and leak free, be

sure to rinse off the leak testing solution.

Step 7. OUTSIDE AIR KITS

Optional outside make-up air kits, Model FOAK-

4 or FAOK-4LD (see Figure 22 on Page 16),

may be used with these appliances. Refer to

the installation instructions packaged with the

air kits for speciﬁc installation information.

If used, the outside air kit must be installed

before the ﬁreplace is framed and enclosed in

the ﬁnished wall.

WARNING

Never use an open ﬂame to

check for leaks.

After completing the installation of the optional

outside air vent system the outside air control

lever must be put in service and tested to en-

sure proper operation before completing any

enclosure around the ﬁrebox. Failure to do

so may result in extensive and costly rework.

Before the operation of the vent system can

be tested, the lever securing screw must be

removed. See Figure 21.

The hand operated outside air control lever is

located on the left side of the ﬁreplace opening.

See Figure 21.

To open the outside air shutter, open the bot-

tom control access panel, reach into the control

compartment, and pull the outside air control

lever all the way out. The outside air shutter

should be fully open when the ﬁreplace is in use

and completely closed when the ﬁreplace is not

being used. Closing it when not in use will prevent

outside cold air from entering the dwelling.

CAUTION

Never locate inlet where it can be

blocked by shrubs, snow drifts,

etc. Never locate inlet in garage

or any area where there is another

fuel burning appliance or products

emitting combustible gases such

as paint, gasoline, etc. In cold

climates, it is recommended the

outside air duct be insulated.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Step 9. INSTALLING LOGS, DECORA-

TIVE VOLCANIC STONE AND GLOW-

ING EMBERS

Step 8. VERIFYING APPLIANCE OPERA-

TION

With gas line installed run initial system check-

out before closing up the front of the unit. Follow

the pilot lighting instructions provided in the

Care and Operation Instructions manual. For

piezo igniter location see Figure 23

Note: Instructions are also found on the litera-

ture tag attached to the gas valve train.

When ﬁrst lighting the appliance, it will take

a few minutes for the line to purge itself of

air. Once purging is complete, the pilot and

burner will light and operate as indicated in

the instruction manual. Subsequent lightings

of the appliance will not require such purging.

Inspect the pilot ﬂame (remove logs, if neces-

sary, handling carefully).

Electronic Appliance Checkout

To light the burner, turn ‘ON’ the optional remote

wall switch and turn the gas control switch to

the “ON” position. Ensure the igniter lights the

pilot. The pilot ﬂame should engulf the ﬂame

rod as shown in Figure 25.

Figure 23

SIT Millivolt Appliance Checkout

The pilot ﬂame should be steady, not lifting

or ﬂoating. Flame should be blue in color with

traces of orange at the outer edge.

The top 3/8" (10 mm) at the pilot generator

(thermopile) and the top 1/8" minimum (tip)

of the quick drop out thermocouple should be

engulfed in the pilot ﬂame. The ﬂame should

project 1" (25 mm) beyond the hood at all three

ports (Figure 24).

Replace logs if removed for pilot inspection.

To light the burner; turn “ON” the remote wall

switch and rotate the gas valve control knob

counterclockwise to the “ON” position.

Figure 25

SIT Millivolt Gas Valve

Showing Piezo Igniter Location

Shown with control

compartment door

removed

Piezo Igniter

SIT Millivolt

Gas Valve

Control

Compartment

Figure 24

Thermocouple

Thermopile

Pilot

Nozzels

SIT MILLIVOLT PILOT ASSEMBLY

Igniter Rod

Hood

3/8" to 1/2"

(9 to 13 mm)

Ground

Electrode

Flame Rod

Hot Surface

Igniter

Proper Flame

Adjustment

Pilot

Nozzels

ELECTRONIC PILOT ASSEMBLY

Proper Pilot Flame Appearance

WARNING

•

DO NOT attempt to install the

logs until the appliance instal-

lation has been completed, the

gas line connected and tested

for leaks and the initial burner

operation has been checked

out.

•

The size and position of the log

set was engineered to give the

appliance a safe, reliable and

attractive ﬂame pattern. Any

attempt to use a different log

set in the ﬁreplace will void

the warranty and will result in

incomplete combustion, soot-

ing, and poor ﬂame quality.

•

Logs get very hot and will

remain hot up to one hour

after gas supply is turned off.

Handle only when logs are

cool. Turn off all electricity

to the appliance before you

install volcanic stone, embers

and logs.

•

This appliance is not designed

to burn wood. Any attempt

to do so could cause irrepa-

rable damage to the appliance

and prove hazardous to your

safety.

•

If logs are not installed

according to the log instal-

lation instructions, flame

impingement and improper

combustion could occur and

result in soot and/or excessive

production of carbon monoxide

(CO), a colorless, odorless,

toxic gas.

Locate the packaged carton of logs (which were

located in the ﬁrebox). The decorative volcanic

stone and glowing embers were packaged

separately in plastic bags located in the control

area of the ﬁreplace.

Install the logs per the instructions in the Care

and Operation Manual.

DO NOT attempt to install the logs until the ap-

pliance installation has been completed, the gas

line connected and tested for leaks and the initial

burner operation has been checked out.

Outside Combustion Air Kits

Cat. No. Model No. Description

81L87 FOAK-4 Combustion Air Kit (w/duct)

81L88 FOAK-4LD Combustion Air Kit (w/o duct)

(ref. Form # 750,008M)

Figure 22

Proper Pilot Flame Appearance

3/8"

(9 mm)

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Proper twig placement is critical to prevent sooting. Twigs should be

placed in the gaps between the ﬂame peaks and should be positioned

so that at no time they impinge the ﬂames.

1. Remove the appliance front door.

2. Remove the log set from the interior of the ﬁreplace.

3. Remove the logs from their packaging. Handle logs carefully to prevent

breakage.

4. MPB-4035 & MPB-4540 Models - Remove the restraining strap from

the grate tines. Ensure the grate is fully inserted into the holes on the

ﬁrebox rear panel and over the indents on the ﬁrebox ﬂoor.

Glowing Embers, Vermiculite, Decorative Volcanic Stone And Log

Placement Instructions:

Step 1. Separate the Glowing Embers (Rockwool) into pieces about

the size of a quarter (see Figure 26). Keep the pieces ﬂuffed up, not

matted.

MPB-3328 & MPB-3530 Models -

Distribute these pieces over the burner as shown in Figure 27. Do not use

more than is shown. The glowing embers should not be placed directly

over the large burner slots as shown in Figure 27.

MPB-4035 & MPB-4540 Models -

Place the center log (Log No. 1) on the burner as shown on Page 20.

Distribute the glowing ember pieces at the front of the burner as shown

in Figure 28. Do not use more than is shown. The glowing embers

should not be placed directly over the large burner slots as shown in

Figure 28.

Note: This appliance is provided with enough Glowing Embers for

several applications; do not feel compelled to use all that is in a new

bag. For best glowing effect, replace the ember material annually. Re-

placement Glowing Embers are available (Catalog Number 88L53).

Step 2. Mound up a portion of the vermiculite (light colored material) in

front of the burner and grate. Sprinkle the dark colored decorative volcanic

stone on top of the vermiculite in a pleasing pattern. For best results,

spread in a non-uniform manner while ensuring complete coverage of

the black sheetmetal surface.

See Figure 27 - MPB-3328 or MPB-3530, or Figure 28 - MPB-4035 or

MPB-4540 models.

Note: Do Not place vermiculite or decorative volcanic stone on top of

the gas burner where it will block the burner ports.

Step 3. Position the individual logs as described on Page 18 (MPB-3328),

Page 19 (MPB-3530) or Page 20 (MPB-4035 and MPB-4540).

Note: Your application may not require the use of all of the provided

vermiculite, or decorative volcanic stone. Replacement vermiculite,

volcanic stone and glowing embers is available (see below for ordering

information).

Figure 27

Figure 26

Figure 28

Do Not Place Glowing Embers Over Large Burner Ports

Glowing EmbersVermiculite

(light colored material)

Decorative Volcanic stone

(dark colored material)

Do Not Place Glowing Embers Over Large Burner Ports

Glowing EmbersVermiculite

(light colored material)

Decorative Volcanic stone

(dark colored material)

MPB-3328 and MPB-3530

REFERENCE

Firebox Accessories / Parts

Cat. No. Model No. Description

88L53

FGE Bag of Glowing Embers

H6319

Vermiculite, Bag

80L42 FDVS Bag of Decorative Volcanic Stone

Glowing Embers

Bag of Glowing

Embers (rockwool)

Separate into Quarter

Size (separate) Pieces

MPB-4035 and MPB-4540

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

MPB-3328 LOG PLACEMENT

Position the individual logs as shown below. Logs should be placed

in the order shown. Position the rear log on the brackets at the

rear of the ﬁrebox with the log's notches directly over the brackets.

Position the right log (log no. 3) by inserting the pin from the rear

log into the hole on its upper end. Place the left log and then the

smaller left and right top logs. All logs that have notches to ﬁt over

the grate tines should be positioned with these notches directly

against the grate. All top logs that rest on lower logs, do so over

ﬂattened mounting faces in the bottom logs.

Proper log and twig placement is critical to encourage outstanding

ﬂame appearance and prevent sooting.

Figure 29

LOG SET

Catalog Number

24M1501

* Item

Description (stamped #)

Log, Rear (39-12)

Log, Left (39-1)

Log, Right (39-2)

Log, Top Center (39-13)

Log, Top/Left (39-3)

Log, Top/Right (39-4)

* Item numbers above correspond to photos

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

MPB-3530 LOG PLACEMENT