WilsonPro Pro 1050 Guide d'installation

WILSON PRO

1050

A Wilson Electronics Brand

wilsonpro.com 866.294.1660

User Manual

In-Building Cellular Signal Booster

With In-Line Ampliﬁ cation

ENGLISH FRANÇAIS

Package Content

1

About The WilsonPro 1050 System

2

Key Features

4

Competitive Advantages

5

Post Install Setup

7

1050 Main Status Screen

8

1050 In-Line Status Screens

10

Safety Guidelines

12

Warranty

16

Index

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

WilsonPro 1050

Two-Part Booster

System

2’ Wilson

400 Cable

Lightning Surge

Protector

100’ Wilson

400 Cable

Wide Band Directional

Antenna + 75’

Wilson 400 Cable

Dome Antenna +

100’ Wilson 400 Cable

1EN

Kit 460230

Package

Content

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

FCC Approved

In-Line Ampliﬁ cation

Compensates for up to 300’ of indoor

cable losses using in-line ampliﬁ cation.

Onboard Software For

Better Control

Automatically controlled with onboard

software, ensuring great connectivity

throughout large spaces and multi-story

buildings.

Auto-Calibration

Main booster & In-Line booster

automatically link, communicate &

calibrate.

Extended Dynamic

Range For Continuous

Connectivity

XDR allows the booster system to never

shutdown due to too strong of a signal. No

matter how strong, the booster system will

never overpower and shutdown.

WilsonPro 1050 System

2 EN

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

The WilsonPRO 1050 Cellular Signal

Booster System automatically

compensates for signal loss resulting

from a long indoor RF coax cable run.

Simply connect the 1050 In-Line unit at

a cable length between 100’ and 300’

from the 1050 Main unit. When both

units are powered up, they will begin to

communicate with each other, sending signals and calculating the amount of signal

loss in the cable. Once cable losses are calculated, the gain levels are adjusted

between the 1050 Main and 1050 In-Line units so that only enough extra gain is added

to the system to compensate for the signal loss of the indoor cable.

This capability to overcome signiﬁ cant cable losses allows the 1050 System to provide

cellular coverage in areas that were previously impossible, such as the lower ﬂ oors of

apartment buildings and other multi-dwelling units.

The WilsonPro 1050 system also includes Wilson Electronics’ state-of-the-art XDR

(Extended Dynamic Range) technology that prevents signal overload conditions which

can, in accordance with FCC regulations, force a booster to shut down.

When the WilsonPro 1050 system senses that any incoming cell signal is too strong,

and threatens to overload the system, XDR automatically reduces signal gain to

compensate for this overload condition while maintaining signal coverage throughout

the building. In contrast, competing signal boosters shut down when they reach

a maximum incoming signal strength threshold, causing the indoor cell signal to

drop out. Both antenna ports are located on the top of the 1050 Main unit for easy

installation. Like all WilsonPro cell signal boosters, the WilsonPRO 1050 Cellular Signal

Booster System is universal: it works for all cellular devices, all services including 4G

LTE, and all U.S. and Canada cell phone carriers.

In-Line Ampliﬁ cation

3EN

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

FCC Approved In-Line Ampliﬁ cation: Compensates for up to 300’ of

indoor cable losses using in-line ampliﬁ cation, providing cell coverage

to hard-to-reach areas.

Onboard Software for Better Control: Booster is automatically

controlled with automatic onboard software, ensuring great

connectivity throughout large spaces and multi-story buildings.

The booster will adjust its gain level up or down as required by the

conditions of the immediate signal environment.

Extended Dynamic Range (XDR) for continuous connectivity: Gives

the 1050 much greater tolerance for a strong incoming signal from the

tower. XDR lets the 1050 system work with an incoming signal stronger

than any competing booster and never shuts down due to a strong

outside signal.

Automatic Calibration: Main booster and In-Line booster

automatically link, communicate, and calibrate.

4 EN

Key Features

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

Highest Downlink Power: Up to +15dB more downlink power than

the competition allows for stronger signal in environments where

the incoming signal is weak. The beneﬁ t is a stronger signal sent to

the inside antennas, providing larger coverage area from a single

booster.

Highest Uplink Power: This allows for a stronger signal transmitted

to the tower, up to +3dB more than the competition, providing greater

user capacity and increased range from the cell site.

Lower Overload and Shutdown Threshold: No matter how strong

the outside signal, the WilsonPro 1050 system never shuts down.

This is a huge beneﬁ t in strong signal environments like cities and

locations close to a carrier tower.

Intelligent Control: WilsonPro cellular boosters automatically adjust

signal gain while still providing even signal coverage throughout the

building.

Sophisticated Software: Cellular signals are constantly ﬂ uctuating.

The software is always monitoring signal levels and making

immediate adjustments as needed, allowing the booster to operate at

maximum gain consistently.

5EN

Competitive

Advantages

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

Outside

Directional

Antenna

to power

Lightning

Surge Protector

1050 Main

1050 In-Line

Inside Dome

Antenna

power

o p

CABLE LOSS

Simple wall-mount

installation.

The direction of the

outside antenna should

be adjusted until the

“DL” bar is maximized.

A Wilson Lightning Surge Protector is recommended for all building installations. Make

sure the protector is installed outside the building at point of entry connected to a

suitable ground and in line between the Outside Antenna and the Signal Booster.

6 EN

Installation

Diagram

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

Inside Antenna

Lightning Surge

Protector

Outside Antenna

1050 In-Line

(placed at a cable length of 100’ to 300’)

1050 Main

to power

The WilsonPRO 1050 System is designed with

advanced internal programming, which allows it to

automatically adjust for a variety of conditions, while

still boosting weak signals.

Once the AC power cable and antenna cables are

connected, turn the unit on by toggling the power

switch located near the AC power receptacle.

7EN

Post Install

Setup

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

Upon power up, the 1050 MAIN unit will attempt to begin it’s calibration routine, which

lasts approximately 14 seconds during which time one of the following messages will

appear on the screen:

Boot Screen

BAND SELECT

RESET

CABLE LOSS

BAND SELECT

RESET

CABLE LOSS

BAND SELECT

RESET

CABLE LOSS

The 1050 In-Line unit has been found

and is communicating with the 1050

Main. Cable loss calibration is in

progress.

The 1050 In-Line unit has not been

found.

8 EN

1050 Main

Status Screen

In-Line Found Screen

No In-Line Screen

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

BAND SELECT

RESET

CABLE LOSS

BAND SELECT

RESET

CABLE LOSS

BAND SELECT

RESET

CABLE LOSS

Failed cable loss calibration. Cable loss

must be between 4dB and 25dB for all

bands. If the cable loss is calculated to

be outside of this range, calibration

will fail. This range corresponds

between 100 feet and 300 feet of

Wilson 400 Cable.

Once cable calibration has successfully

completed, the band status screens will

appear.

Pressing the Cable Loss Button will

display the cable loss compenstion at

the upper bands and lower bands.

9EN

Failed Calibration Screen

Cable Loss Button

1050 Main Status Screen (cont.)

Successful Calibration Screen

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

The 1050 In-Line has 3 status lights:

GREEN: Normal

RED: One or more bands has shut

o due to OSCILLATION.

1050 In-Line

CABLE CAL COM STATUS

1050 In-Line

CABLE CAL COM STATUS

10 EN

1050 In-Line

Status Lights

‘STATUS’ LED:

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

GREEN: Normal, waiting for next

communications event

GREEN: Calibration complete.

ORANGE: Brief orange blink when

communicating with 1050 Main.

ORANGE: Calibration in process.

RED: Communications failure when

attempting to communicate with

1050 Main.

RED: Calibration failed.

1050 In-Line

CABLE CAL COM STATU

L

in

e

S

TA

STATU

STA

I

n

n-L

i

I

-L

i

in

105

0

CABLE CAL COM

5

0

CO

M

1

05

0

L

1

5

0

L

11EN

‘COM’ LED:

‘CABLE CAL’ LED:

1050 In-LIne Status Screen (cont.)

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

Warnings

To uphold compliance with network protection standards, all active cellular devices must maintain at

least 6 feet of separation distance from Panel and Dome antennas.

Use only the power supply provided in this package. Use of a non-Wilson Electronics product may

damage your equipment.

The Signal Booster unit is designed for use in an indoor, temperature-controlled environment (less than

100 degrees Fahrenheit). It is not intended for use in attics or similar locations subject to temperatures

in excess of that range.

RF Safety Warning: Any antenna used with this device must be located at least 8 inches from all

persons.

AWS Warning: The Outside Antenna must be installed no higher than 10 meters (31’9”) above ground.

This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by weBoost could void the authority to operate this equipment.

FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR

WIRELESS PROVIDER, PLEASE SEE BELOW:

Sprint: http://www.sprint.com/legal/fcc_boosters.html

T-Mobile/MetroPCS: https://support.t-mobile.com/docs/DOC-9827

Verizon Wireless: http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html

AT&T: https://securec45.securewebsession.com/attsignalbooster.com/

U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp

This is a CONSUMER device.

BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have

your provider’s consent. Most wireless providers consent to the use of signal boosters.

Some providers may not consent to the use of this device on their network. If you are

unsure, contact your provider.

In Canada, BEFORE USE you must meet all requirements set out in ISED CPC-2-1-05.

You MUST operate this device with approved antennas and cables as speciﬁ ed by the

manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from (i.e., MUST

NOT be installed within 20 cm of) any person.

You MUST cease operating this device immediately if requested by the FCC (or ISED in

Canada) or licensed wireless service provider.

WARNING. E911 location information may not be provided or may be inaccurate for calls

served by using this device.

This device may be operated ONLY in a ﬁ xed location (i.e..may operate in a ﬁ xed location

only) for in-building use.

12 EN

Safety Guidelines

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

The following accessories are certiﬁ ed by the FCC to be used with the

Wilson PRO 1050 System.

In-Line Box-To-Box Expansion Kit*

Kit 952300-1N

1 - 100’ Wilson 400 Cable

1 - N-Female to N-Female Connector

Kit 952300-2N

2 - 100’ Wilson 400 Cable

2- N-Female to N-Female Connector

* Only Wilson Kit 952300-1N / Kit

952300-2N are authorized for

extension of 200ft and 300ft total

length on box-to-box connection.

Inside Antenna Expansion Kit

Kit 309900-50N40090

2 - Wall Panel antennas

1 - 50 ohm 3-Way Splitter

1 - 100' Wilson 400

Kit 309905-50N17420

3 - Wall Panel Antennas

3 - 2-Way 50 Ohm Splitters

20' RG174

Kit 309902-75F0650

2 - Wall Panel Antennas

1 - 3-Way 75Ohm Splitter

50' RG6

Kit 309903-75F1180

3 - Wall Panel Antennas

3 - 2-Way 75Ohm Splitters

80' RG11 cable

Kit 309904-75F5830

1 - Wall Panel Antenna

1 - 2-Way 75 Ohm Splitter

30' RG58 cable

Inside Antenna Kits

Kit 311155-0670

75 Ohm Wall mount Panel Antenna

70’ RG6 Cable

Kit 311135-5840

50 Ohm Wall mount Panel Antenna

40’ RG58 Cable

Kit 311135-400150

50 Ohm Wall mount Panel Antenna

150' Wilson 400

Kit 311155-11120

75 Ohm Wall mount Panel Antenna

10’ RG11 cable

Kit 304412-400100

50 Ohm 4G Dome Antenna

100' Wilson400 cable

Kit 304412-5830

50 Ohm 4G Dome Antenna

30' RG58 cable

Kit 304419-1175

75 Ohm 4G Dome Antenna

75' RG 11 cable

Kit 304419-17450

75 Ohm 4G Dome Antenna

50' RG174 cable

May need separate adapter

Kit 304419-0650

75 Ohm 4G Dome Antenna

50' RG6 cable

50 Ohm Outside Antenna Kits

Kit 314453-5825

50 Ohm Pole Mount Panel Antenna

25’ RG58 Cable

Kit 314411-5825

50 Ohm Wide Band Directional

25’ RG58 Cable

Kit 301111-5850

Yagi Directional Antenna

50’ RG58 Cable

Kit 311203-5820

Omni-Directional antenna

20’ RG58 Cable

Kit 314411-40075

50 Ohm Wide Band Directional

75’ LMR400 Cable

Kit 311203-40020

Omni-Directional antenna

20’ LMR400 Cable

Kit 301111-400170

Yagi Directional w/ N-Female

170’ LMR400

Kit 314453-40075

50 Ohm Pole Mount Panel Antenna

75’ LMR400 Cable

Kit 304422-40020

50 Ohm 4G Omni Antenna

20’ Wilson400 cable

Kit 304422-5810

50 Ohm 4G Omni Antenna

10’ RG58 cable

Kit 304422-1120

50 Ohm 4G Omni Antenna

20’ RG11 cable

May need separate adapter

75 Ohm Outside Antenna Kits

Kit 301111-0675

Yagi Directional Antenna

75’ RG6 Cable

N-Male to F-Female adapter

Kit 311201-0620

Omni Directional w/ F-Female

20’ RG6 Cable

Kit 314473-0640

75 Ohm Pole Mount Panel Antenna

40’ RG6 Cable

Kit 311141-0620

75 Ohm Grey Brick Antenna

20’ RG6 Cable

Kit 301111-11140

Yagi Directional Antenna

140’ RG11 Cable

N-Male to F-Female adapter

Kit 311201-1120

Omni Directional w/ F-Female

20’ RG11 Cable

Kit 314473-1175

75 Ohm Pole Mount Panel Antenna

75’ RG11 Cable

Kit 314475-0630

75 Ohm Wide Band Directional

30’ RG6 Cable

Kit 314475-1175

75 Ohm Wide Band Directional

75’ RG11 Cable

Kit 311141-1120

75 Ohm Grey Brick Antenna

20’ RG11 Cable

Kit 304421-17410

75 Ohm 4G Omni Antenna

10’ RG174 cable

Kit 304421-0610

75 Ohm 4G Omni Antenna

10’ RG6 cable

Kit 304421-5810

75 Ohm 4G Omni Antenna

10’ RG58 cable

May need separate adapter

Kit 304421-1120

75 Ohm 4G Omni Antenna

20’ RG 11 cable

13EN

Antenna Kit Options

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

Product Number 460030

Model Number 460030

FCC ID

PWO460030 / PWO0460030IL

IC ID

4726A-460030

Connectors N-Female

Antenna Impedance 50 Ohms

Frequency

698-716 MHz, 729-746 MHz, 746-756 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz,

1710-1755/2110-2155 MHz

Power output for single cell

phone (Uplink) dBm

700MHz Band12/17 700MHz Band13 800MHz 1700MHz 1900MHz

24.7 24.7 24.4 25.1 24.5

Power output for single cell

phone (Downlink) dBm

700

MHz Band12/17 700MHz Band13 800MHz 2100MHz 1900MHz

14.8 14.3 15.6 15 15.1

1050 Main 1050 In-Line

Noise Figure 5 dB nominal 5 dB nominal

Isolation > 90 dB > 90 dB

Power Requirements

110-220V AC 5V 3A

The term “IC” before the radio certiﬁ cation number only signiﬁ es that Industry Canada technical speciﬁ cations were met.

Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be

adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter

incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster

is not in use for ﬁ ve minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency

band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power o on that

band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1

minute. After 5 (ﬁ ve) such automatic restarts, any problematic bands are permanently shut o until the Signal Booster

has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity

are maintained by the Signal Booster’s microprocessor.

14 EN

Speciﬁ cations

IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION

WILSON PRO 1050 SYSTEM

15EN

Notes

30 DAY MONEY-BACK GUARANTEE

All WilsonPro products are protected by WilsonPro 30-day money-back guarantee.

If for any reason the performance of any product is not acceptable, simply return

the product directly to the reseller with a dated proof of purchase.

3 YEAR WARRANTY

WilsonPro Boosters are warranted for three (3) years against defects in

workmanship and/or materials. Warranty cases may be resolved by returning the

product directly to the reseller with a dated proof of purchase.

Signal Boosters may also be returned directly to the manufacturer at the

consumer’s expense, with a dated proof of purchase and a Returned Material

Authorization (RMA) number supplied by WilsonPro. WilsonPro shall, at its option,

either repair or replace the product.

This warranty does not apply to any Signal Boosters determined by WilsonPro

to have been subjected to misuse, abuse, neglect, or mishandling that alters or

damages physical or electronic properties.

Replacement products may include refurbished WilsonPro products that have been

recertified to conform with product specifications.

RMA numbers may be obtained by contacting Customer Support.

DISCLAIMER: The information provided by WilsonPro is believed to be complete and

accurate. However, no responsibility is assumed by WilsonPro for any business or

personal losses arising from its use, or for any infringements of patents or other rights

of third parties that may result from its use.

NEED HELP?

support.wilsonpro.com 866.294.1660

Warranty

WILSON PRO

1050

Une marque Wilson Electronics

Guide de l’utilisateur

Ampliﬁ cateur de signal cellulaire pour bâtiment

avec système d’ampliﬁ cation en ligne

wilsonpro.com 866.294.1660

FRANÇAIS

Contenu de l'ensemble

1

À propos du système WilsonPro 1050

2

Caractéristiques clés

4

Avantages comparativement à la concurrence

5

Réglage après l’installation

7

Écran d'état principal du 1050

8

Écrans d'état de l’ampliﬁ cation en ligne du 1050

10

Directives de sécurité

12

Garantie

17

Table des matières

La page charge ...

WilsonPro Pro 1050 Guide d'installation

WilsonPro Pro 1050 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents