Samsung RS30GKASL Manuel utilisateur

Catégorie
Frigos
Taper
Manuel utilisateur

Ce manuel convient également à

English
Refrigerator
user manual
imagine the possibilities
Thank you for purchasing a Samsung product.
Free Standing Appliance
This manual is made with 100% recycled paper.
02_ safety information
SAFETY INFORMATION
Before operating the appliance, please read this
manual thoroughly and retain it at a safe place
near the appliance for your future reference.
Use this appliance only for its intended purpose
as described in this instruction manual. This
appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge if they have been
given supervision or instruction concerning use of
the appliance in a safe way and understand the
hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
Warnings and Important Safety Instructions in this
manual do not cover all possible conditions and
situations that may occur. It is your responsibility
to use common sense, caution, and care when
installing, maintaining, and operating your
appliance.
Because these following operating instructions
cover various models, the characteristics of
your refrigerator may differ slightly from those
described in this manual and not all warning signs
may be applicable. If you have any questions or
concerns, contact your nearest service center
or find help and information online at www.
samsung.com.
Important safety symbols and
precautions:
WARNING
Hazards or unsafe practices that may
result in severe personal injury or
death.
CAUTION
Hazards or unsafe practices that may
result in minor personal injury or
property damage.
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions carefully.
Unplug the power plug from the wall
socket.
Make sure the machine is grounded to
prevent electric shock.
Call the contact center for help.
Note.
These warning signs are here to prevent injury to
you and others.
Please follow them carefully.
After reading this section, keep it in a safe place
for future reference.
CE Notice
This product has been determined to be in
compliance with the Low Voltage Directive
(2006/95/EC), the Electromagnetic Compatibility
Directive (2004/108/EC), RoHS Directive (2011/65/
EU), Commission Delegated Regulation (EU) No
1060/2010 and the Eco-Design Directive(2009/125/
EC) implemented by Regulation (EC) No 643/2009 of
the European Union. (For products sold in European
Countries only)
SEVERE WARNING SIGNS FOR
TRANSPORTATION AND SITE
When transporting and installing the
appliance,care should be taken to ensure
that no parts of the refrigerating circuit are
damaged.
R-600a or R-134a is used as a refrigerant. Check
the compressor label on the rear of the appliance
or the rating label inside the refrigerator to see
which refrigerant is used for your refrigerator.
When this product contains flammable gas
(Refrigerant R-600a),
- Refrigerant leaking from the pipe work could
ignite or cause an eye injury. If a leak is detected,
avoid any naked flames or potential sources of
ignition and air the room in which the appliance is
standing for several minutes.
- In order to avoid the creation of a flammable
gas-air mixture if a leak in the refrigerating
WARNING
safety information
safety information _03
circuit occurs, the size of the room in which the
appliance may be sited depends on the amount
of refrigerant used.
- Never start up an appliance showing any signs
of damage. If in doubt, consult your dealer. The
room where the refrigerator will be sited must
be 1m³ in size for every 8g of R-600a refrigerant
inside the appliance. The amount of refrigerant
in your particular appliance is shown on the
identification plate inside the appliance.
- If the appliance contains isobutane refrigerant
(R-600a), a natural gas with high environmental
compatibility that is, however, also combustible.
When transporting and installing the appliance,
care should be taken to ensure that no parts of
the refrigerating circuit are damaged.
SEVERE WARNING SIGNS
FOR INSTALLATION
Do not install this appliance in a humid, oily
or dusty location, in a location exposed to
direct sunlight and water (rain drops).
- Deteriorated insulation of electrical parts may
cause an electric shock or fire.
Do not place this refrigerator in direct sunlight or
expose to the heat from stoves, room heaters or
other appliances.
Do not plug several appliances into the same
multiple power board.
The refrigerator should always be plugged into
its own individual electrical outlet which has a
voltage rating that matched the rating plate.
- This provides the best performance and also
prevents overloading house wiring circuits, which
could cause a fire hazard from overheated wires.
If the wall socket is loose, do not insert the power
plug.
- There is a risk of electric shock or fire.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
Do not bend the power cord excessively or place
heavy articles on it.
Do not use aerosols near the refrigerator.
- Aerosols used near the refrigerator may cause an
explosion or fire.
Do not install this appliance in a location where
gas may leak.
- This may result in an electric shock or fire.
The installation or any service of this
appliance is recommended by a qualified
technician or service company.
- Failing to do so may result in an electric shock,
fire, explosion, problems with the product, or
WARNING
injury.
This refrigerator must be properly installed and
located in accordance with the manual before it
is used.
Connect the power plug in proper position with
the cord hanging down.
- If you connect the power plug upside down, wire
can get cut off and a cause fire or an electric
shock.
Make sure that the power plug is not squashed
or damaged by the back of the refrigerator.
When moving the refrigerator, be careful not to
roll over or damage the power cord.
- This constitutes a fire hazard.
The appliance must be positioned so that the
plug is accessible after installation.
The refrigerator must be grounded.
- You must ground the refrigerator to
prevent any power leakages or electric
shocks caused by current leakage from
the refrigerator.
Never use gas pipes, telephone lines or other
potential lightening rods as ground.
- Improper use of the ground plug can result in an
electric shock.
If the power cord is damaged, have it
replaced immediately by the manufacturer
or its service agent.
The fuse on the refrigerator must be changed by
a qualified technician or service company.
- Failing to do so may result in an electric shock or
personal injury.
CAUTION SIGNS FOR
INSTALLATION
Keep ventilation opening in the appliance
enclosure or mounting structure clear of
obstruction.
Allow the appliance to stand for 2 hours after
installation.
SEVERE WARNING SIGNS
FOR USING
Do not insert the power plug with wet
hands.
Do not store articles on the top of the appliance.
- When you open or close the door, the articles
may fall and cause a personal injury and/or
material damage.
Do not put items filled with water on the
CAUTION
WARNING
04_ safety information
refrigerator.
- If spilled, there is a risk of fire or electric shock.
Do not let children hang on the door.
- Failure to do so may cause serious personal
injury.
Do not leave the doors of the refrigerator open
while the refrigerator is unattended and do not let
children enter inside the refrigerator.
Do not allow babies or children go inside the
drawer.
- It can cause death from suffocation by
entrapment or personal injury.
Do not sit on the Freezer door.
- The door may be broken and cause a personal
injury.
To prevent children entrapment, you must reinstall
the divider using provided screws after cleaning
or other actions if you removed the divider from
the drawer.
Never put fingers or other objects into the
dispenser hole.
- Failure to do so may cause personal injury or
material damage.
Do not store volatile or flammable substances
such as benzene, thinner, alcohol, ether or LP
gas in the refrigerator.
- The storage of any of such products may cause
an explosion.
Do not store low temperature-sensitive
pharmaceutical products, scientific materials or
other low temperature-sensitive products in the
refrigerator.
- Products that require strict temperature controls
must not be stored in the refrigerator.
Do not place or use electrical appliance inside
the refrigerator, unless they are of a type
recommended by the manufacturer.
Do not use a hair dryer to dry the inside of the
refrigerator. Do not place a lighted candle in the
refrigerator for removing bad odors.
- This may result in an electric shock or fire.
Do not touch the inside walls of the freezer or
products stored in the freezer with wet hands.
- This may cause frostbite.
Do not use mechanical devices or any other
means to accelerate the defrosting process, other
than those recommended by the manufacturer.
Do not damage the refrigerant circuit.
This product is intended only for the
storage of food in a domestic environment.
Bottles should be stored tightly together so that
they do not fall out.
In the event of a gas leak (such as propane
gas, LP gas, etc.), ventilate immediately without
touching the power plug. Do not touch the
appliance or power cord.
- Do not use a ventilating fan.
- A spark may result in an explosion or fire.
Use only the LED Lamps provided by
manufacturer or service agent.
Children should be supervised to ensure that they
do not play with and/or climb into the appliance.
Do not disassemble or repair the
refrigerator by yourself.
- You run a risk of causing a fire, malfunction and/
or personal injury. In case of malfunction, please
contact your service agent.
If the appliance generates a strange noise,
a burning or smell or smoke, unplug the
power plug immediately and contact your
nearest service center.
- Failing to do so may result in an electric or fire
hazards.
If you experience difficulty when changing the
light, contact service agent.
If the products is equipped with the LED Lamp,
do not disassemble the Lamp Cover and LED
Lamp by yourself.
- Please contact your service agent.
If any dust or water is in the refrigerator, pull
out power plug and contact your Samsung
Electronics service center.
- There is a risk of fire.
CAUTION SIGNS FOR USING
To get best performance from the product,
- Do not place foods too closely in front of
the vents at the rear of the appliance as
it can obstruct free air circulation in the
refrigerator compartment.
- Wrap the food up properly or place it in airtight
containers before putting it into the refrigerator.
- Do not put any newly introduced food for freezing
near to already existing food.
Do not place carbonated or fizzy drinks in the
freezer compartment. Do not put bottles or glass
containers in the freezer.
- When the contents freeze, the glass may break
and cause personal injury and property damage.
Do not change or modify the functionality of the
refrigerator.
- Changes or modifications may result in a personal
injury and/or property damage. Any changes or
modifications performed by a 3rd party on this
completed appliance are neither covered under
Samsung warranty service, nor is Samsung
responsible for safety issues and damages that
result from 3rd party modifications.
Do not block air holes.
CAUTION
safety information _05
- If the air holes are blocked, especially with a
plastic bag, the refrigerator can be over cooled. If
this cooling period lasts too long, the water filter
may break and cause water leakage.
- Do not put any newly introduced food for freezing
near to already existing food.
Please observe maximum storage times and
expiry dates of frozen goods.
Fill the water tank, ice tray, water cubes only with
potable water.
Use only the ice-maker provided with the
refrigerator.
The water supply to this refrigerator must only be
installed/connected by a suitably qualified person
and connected to a potable water supply only.
In order to operate the ice-maker properly, water
pressure of 138~862kpa(1.4~8.8kgf/cm3) is
required.
Do not spray volatile material such as insecticide
onto the surface of the appliance.
- As well as being harmful to humans, it may also
result in an electric shock, fire or problems with
the product.
Do not apply strong shock or excessive force
onto the surface of glass.
- Broken glass may result in a personal injury and/
or property damage.
CAUTION SIGNS FOR CLEANING
AND MAINTENANCE
Do not directly spray water inside or
outside the refrigerator.
- There is a risk of fire or electric shock.
Do not use or place any substances sensitive
to temperature such as inflammable sprays,
inflammable objects, dry ice, medicine, or
chemicals near the refrigerator. Do not keep
volatile or inflammable objects or substances
(benzene, thinner, propane gas, etc.) in the
refrigerator.
- This refrigerator is for storing food only.
- This may result in a fire or an explosion.
Do not spray cleaning products directly on the
display.
- Printed letters on the display may come off.
Remove any foreign matter or dust from the
power plug pins. But do not use a wet or damp
cloth when cleaning the plug, remove any foreign
material or dust from the power plug pins.
- Otherwise there is a risk of fire or electric shock.
Never put fingers or other objects into the
dispenser hole and ice chute.
- It may cause a personal injury or material
damage.
CAUTION
Unplug the refrigerator before cleaning and
performing maintenance.
SEVERE WARNING SIGNS
FOR DISPOSAL
Ensure that none of the pipes on the back
of the appliance are damaged prior to
disposal.
R-600a or R-134a is used as a refrigerant. Check
the compressor label on the rear of the appliance
or the rating label inside the refrigerator to see
which refrigerant is used for your refrigerator.
When this product contains flammable gas
(Refrigerant R-600a), contact your local authority
in regard to safe disposal of this product.
Cyclopentane is used as an insulation blowing
gas. The gases in insulation material require
special disposal procedure. Please contact your
local authorities in regard to the environmentally
safe disposal of this product. Ensure that none
of the pipes on the back of the appliances are
damaged prior to disposal. The pipes shall be
broken in the open space.
When disposing of this product or other
refrigerators, remove the door/door seals, door
latch so that small children or animals cannot
become trapped inside. Leave the shelves in
place so that children may not easily climb inside.
Children should be supervised to ensure that they
do not play with the old appliance.
Please dispose of the packaging material for this
product in an environmentally friendly manner.
ADDITIONAL TIPS FOR PROPER USAGE
In the event of a power failure, call the local office
of your Electricity Company and ask how long it
is going to last.
- Most power failures that are corrected within
an hour or two will not affect your refrigerator
temperatures. However, you should minimize the
number of door openin gs while the power is off.
- Should the power failure last more than 2 hours,
remove all ice in the Ice Bucket.
- Should the power failure last more than 24 hours,
remove all frozen food.
If keys are provided with the refrigerator, the keys
should be kept out of the reach of children and
not be in the vicinity of the appliance.
The appliance might not operate consistently
(possibility of temperature becoming too warm
in the refrigerator) when sited for an extended
period of time below the cold end of the range of
temperature for which the refrigerating appliance
WARNING
06_ safety information
is designed.
Do not store food which spoils easily at low
temperature, such as bananas, melons.
Your appliance is frost free, which means there is
no need to manually defrost your appliance, as
this will be carried out automatically.
Temperature rise during defrosting can comply
with ISO requirements. But if you want to prevent
an undue rise in the temperature of the frozen
food while defrosting the appliance, please wrap
the frozen food up in several layers of newspaper.
Any increase in temperature of frozen food during
defrosting can shorten its storage life.
Saving Energy Tips
- Install the appliance in a cool, dry room with
adequate ventilation.
Ensure that it is not exposed to direct sunlight
and never put it near a direct source of heat
(radiator, for example).
- Never block any vents or grilles on the appliance.
- Allow warm food to cool down before placing it in
the appliance.
- Put frozen food in the refrigerator to thaw. You
can then use the low temperatures of the frozen
products to cool food in the refrigerator.
- Do not keep the door of the appliance open for
too long when putting food in or taking food out.
The shorter time for which the door is open, the
less ice will form in the freezer.
- Clean the rear of the refrigerator regularly. Dust
increases energy consumption.
- Do not set temperature colder than necessary.
- Ensure sufficient air exhaust at the refrigerator
base and at the back wall of the refrigerator. Do
not cover air vent openings.
- Allow clearance to the right, left, back and top
when installing.
This will help reduce power consumption and
keep your energy bills lower.
- For the most efficient use of energy, please keep
the all inner fittings such as baskets, drawers,
shelves on the position supplied by manufacturer.
This appliance is intended to be used
in household and similar applications
such as
- staff kitchen areas in shops, offices and other
working environments;
- farm houses and by clients in hotels, motels and
other residential type environments;
- bed and breakfast type environments;
- catering and similar non-retail applications.
contents
SETTING UP YOUR SIDE-BY-SIDE REFRIGERATOR ……………………………………………………… 07
OPERATING THE SAMSUNG SIDE-BY-SIDE REFRIGERATOR …………………………………………… 13
TROUBLESHOOTING …………………………………………………………………………………………… 19
setting up _07
01 SETTING UP
GETTING READY TO INSTALL
THE REFRIGERATOR
Congratulations on the purchase of your Samsung
Side-By-Side Refrigerator. We hope you will enjoy
the many state-of-the-art features and ef ciencies
that this new appliance has to offer.
Selecting the best location for the
refrigerator
Select a location with easy access to a water supply.
Select a location without direct exposure to sunlight.
Select a location with level (or nearly level)
flooring.
Select a location with enough space for the
refrigerator doors to open easily. See the diagram
below.
Select a location that allows sufficient space to
the right,left, back, and top for air circulation. See
the diagram below.
Select a location that allows you to move the
refrigerator easily if it needs maintenance or service.
When moving your refrigerator
To prevent fl oor damage, be sure the front levelling
legs are in the up position (above the fl oor). Refer to
‘Levelling the refrigerator’ in this manual (page 9).
To protect the fi nish of your fl ooring while you are
installing the refrigerator, place a large section of the
cardboard carton under the refrigerator where you
are working.
When installing, servicing or cleaning behind
the refrigerator, be sure to pull the unit straight
out and push back straight in after fi nishing.
setting up your side-by-side
refrigerator
50mm
50mm
50mm
50mm
at least 6mm
at least 6mm
at least 6mm
at least 6mm
1727mm
1727mm
1181mm
1181mm
974mm
974mm
1016mm
1016mm
1308mm
1308mm
Leg
Leg
Screw Driver
Screw Driver
CAUTION
08_ setting up
2. Remove two water lines (White one is for water
and the other one is for ice) by pressing the
coupler (1) and pulling the water line (2) away.
Reattaching the Water Supply Line
1. The Water Line must be fully Inserted to the
center of transparent coupler to prevent water
leakage from the dispenser.
2. Insert the 2 clips in the install pack and check
that it holds the line firmly.
Do not cut the water line. Gently separate it
from the coupler.
Removing the freezer door
A few things to mention fi rst.
Make sure that you lift the door straight up so the
hinges are not bent or broken.
Be careful not to pinch the water tubing and wire
harness on the door.
Place doors on a protected surface to prevent
scratching or damage.
SETTING UP THE
REFRIGERATOR
Now that you have your new Refrigerator installed in
place, you are ready to set up and enjoy the features
and functions of the appliance. By completing the
following steps, your Refrigerator should be fully
operational. If not, fi rst check the power supply and
electricity source or try the troubleshooting section
at the back of this user’s guide. If you have any
further questions, contact your Samsung Electronics
service center.
1. Place the Refrigerator in an appropriate location
with reasonable clearance between the wall and
the Refrigerator. Refer to installation instructions
in this manual.
2. Once the Refrigerator is plugged in, make sure
the interior light comes on when you open the
doors.
3. Set the Temperature control to the coldest
temperature and wait for an hour. The Freezer
will get slightly chilled and the motor will run
smoothly.
4. After powering the Refrigerator, it will take a few
hours to reach the appropriate temperature. You
can store food and drinks in the Refrigerator after
the temperature is sufficiently cool.
SETTING UP THE
REFRIGERATOR DOORS
If your entrance won’t allow the refrigerator to pass
easily through it, you can remove the doors.
Separating the Water Supply Line
from the Refrigerator
1. Pull the two water lines (which are in the Fixer)
out to the front.
1
2
Make sure the color of the
Make sure the color of the
water lines match.
water lines match.
Center of transparent
Center of transparent
coupler
coupler
clip A (1/4”)
clip A (1/4”)
(6.35mm)
(6.35mm)
setting up _09
01 SETTING UP
Removing the Fridge Door
1. Remove a screw on the upper hinge cover
1
.
With the door open, disengage the two locking
tabs with a flat-head screw driver
2
and remove
it while the lifting up the rear of the cover
3
, and
then disconnect the wires by gently pulling them
apart
4
.
2. Removing the FIXER HINGE ,and next take off
the upper hinge. Be careful that the door does
not fall on you as you are removing it.
Be sure to keep track of all parts you are
removing.
3. Remove the door from the
lower hinge
5
by lifting
the door straight up
6
.
Reattaching the Fridge door
To reattach the fridge doors, replace parts in
reverse order.
LEVELLING THE
REFRIGERATOR
Now that the doors are back on the refrigerator, you
want to make sure the refrigerator is level so that
you can make fi nal adjustments. If the refrigerator
is not level, it will not be possible to get the doors
perfectly even.
1. Remove a screw on the upper hinge cover
1
.
With the door open, disengage the two locking
tabs with a flat-head screw driver
2
and remove
it while the lifting up the rear of the cover
3
, and
then disconnect the wires by gently pulling them
apart
4
.
2. Removing the FIXER HINGE ,and next take off
the upper hinge. Be careful that the door does
not fall on you as you are removing it.
Be sure to keep track of all parts you are
removing.
3. Next, remove the door from the lower hinge
5
by carefully lifting the door straight up
6
.
Be careful not to pinch the water tubing and
wire harness on the door.
Reattaching the freezer doors
To reattach the freezer doors, replace parts in
reverse order
CAUTION
CAUTION
CAUTION
CAUTION
6
5
6
5
3
2
4
1
3
2
4
1
10_ setting up
When the door of the freezer is higher
than the fridge
Insert a fl at-blade screwdriver into a slot on the
fridge leg, then turn it clockwise.
CHECKING THE WATER
DISPENSER LINE
A water dispenser is one of the helpful features on
your new Samsung Refrigerator. To help promote
better health, the Samsung water fi lter removes
unwanted particles from your water. However, it
does not sterilize or destroy microorganisms. You
may need to purchase a water purifying system to
do that.
In order for the ice maker to operate properly, a
water pressure of 20~125 psi (pound per square
inch) is required. Under normal conditions, a 170 cc
(5.75 oz.) paper cup can be fi lled in 10 seconds.
If the Refrigerator is installed in an area with low
water pressure (below 20psi), you can install a
booster pump to compensate for the low pressure.
Make sure the water storage tank inside the
Refrigerator is properly fi lled. To do this, press the
water dispenser lever until the water runs from the
water outlet.
Water line installation kits are available at extra
cost from your dealer. We recommend using a
water supply kit that contains copper tubing.
The new hose-sets supplied with the
appliance are to be used and that old hose-
sets should not be reused.
Check the accessory list below.
Water line fixer and
screws
Pipe connector
Water line Clip
When the Freezer part is lower than
the Fridge part.
Insert a fl at-blade screwdriver into a slot on the
Freezer Leg, then turn it clockwise.
When the Fridge part is lower than
the Freezer part.
Insert a fl at-blade screwdriver into a slot on the
Fridge Leg, then turn it clockwise.
Refer to the next section for the best way to
make very minor adjustments to the doors.
MAKING MINOR ADJUSTMENTS
TO THE DOORS
Remember, a level refrigerator is necessary for
getting the doors perfectly even. If you need
help, review the previous section on levelling the
refrigerator.
When the door of the fridge is higher
than the freezer
Insert a fl at-blade screwdriver into a slot on the
freezer leg, then turn it clockwise.
Screwdriver(-)
Screwdriver(-)
Freezer Leg
Freezer Leg
Screwdriver(-)
Screwdriver(-)
Fridge Leg
Fridge Leg
setting up _11
01 SETTING UP
If you have to repair or disassemble the water line,
cut off 6.5mm of the plastic tubing to make sure you
get a snug, leak-free connection.
Before being used, the leakage in these
places should be examined
Samsung Warranty does not cover WATER LINE
INSTALLATION.
It’ll be done at customer’s charge unless the retail
price includes installation cost.
Please contact Plumber or Authorized Installer for
the installation if needed.
If Water leakage occurs due to improper
installation, Please contact installer.
1. Slip the compression nut (A) through the supplied
plastic tubing (A).
2. Tighten the compression nut (A) onto the 1/4”
compression fitting.
- If you are using copper tubing, slip the
compression nut (B) (not included) and ferrule
(not included) on copper tubing (not included) as
shown.
- If you are using plastic tubing (B), insert the
molded end(Bulb) of the plastic tubing (B) into
the compression fitting.
Do not use without the molded end(Bulb) of
the plastic tubing (B).
3. Tighten the compression nut (B) onto the
compression fitting. Do not over-tighten the
compression nut (B).
4. Turn water on and check for any leakage.
Only connect the water line to a drinkable
water source.
If you have to repair or disassemble the water
line, cut off 1/4“ of the plastic tubing to make
sure you get a snug, leak-free connection.
Connecting to the water supply line
1. First, shut off the main water supply line.
2. Locate the nearest cold, drinking water line.
3. Follow the Water Line Installation Instructions in
the installation kit.
4. After connecting the water supply to the water
filter, turn your main water supply back on and
Dispense about 3L to clear and prime the water
filter.
Connecting the water line to the
refrigerator
1. Remove the cap from water line on the unit and
insert compression nut to the water line on the
unit after disassembling from provided water line.
2. Connect both water line from the unit and water
line in the kit
3. Tighten the compression nut onto the
compression fitting. Be careful no gap between
two items.
4. Turn water on and check for any leakage.
Only connect the water line to a drinkable
water source.
CAUTION
The water line must be connected to
the cold water pipe.
If it is connected to the hot water pipe,
it may cause the purifier to malfunction.
Close Main
Close Main
Water pipe
Water pipe
Close Main
Close Main
Water pipe
Water pipe
No gap
No gap
Remove
Remove
cap
cap
Water Line
Water Line
from unit
from unit
Water Line
Water Line
from Kit
from Kit
No gap
No gap
Loosen a
Loosen a
CAUTION
No Leak
No Leak
CAUTION
12_ setting up
4. Additional flushing may be required in some
households.
5. Open the refrigerator door and make sure there
are no water leaks coming from the water filter.
A newly installed water fi lter cartridge may
cause water to briefl y spurt from the water
dispenser. This is due to air getting into the
line. It should pose no problem to operation.
Check the amount of water supplied
to the ic
e tray.
1. Lift up the icemaker cover and gently pull it out.
2. When you press the Test button for 3 seconds,
the ice cube container is filled with water from
the water supply tap. Check to make sure the
amount of water is correct (see the illustration
below). If the water level is too low, the ice cubes
will be small. This is a water pressure problem
from within the main water pipes, not the
refrigerator.
- It will take a few minutes for the water to
reach the correct level after you push the
Test button.
- Do not press the test button continuously when
the tray is filled with ice or water. Water may
overflow or ice jamming may occur.
- When the bucket is not installed, the ice maker
does not work.
- When Ice Off blinks on the display panel, reinsert
the bucket and/or make sure it’s installed
properly.
BEFORE USING ICEMAKER
Remove
- Hold the handle as shown in
Figure1.
- Slightly pull up the bottom part.
- Take out the ice bucket slowly.
Install
- Assemble the icemaker in the
reverse order of disassembly.
- Push the bucket in firmly until you
hear a clicking sound.
- If the bucket does not fit into its
place, turn the gear handle on its
back by 90 degrees and reinstall
it again as shown in Figure 2.
Before calling service
- Any sounds you hear when
the ice maker dumps ice into
the bucket are part of normal
operation.
- If you don’t dispense ice for a
long period of time, the ice may
form clumps in the ice bucket. If ice clumps form,
remove the remaining ice and empty the bucket.
- When ice does not come out, check for ice stuck
in the chute and remove it.
- When Ice Off blinks on the display panel,
reinsert the bucket and/or make sure it’s
installed properly.
- When the door is open, the Ice and water
dispenser do not work.
- If you close the door hard, it may cause water
spilling over the ice maker.
- To prevent dropping the ice bucket, use both
hands when removing it.
- To prevent injury, be sure to clean up any ice or
water that may have dropped on the floor.
- Do not let the children hang on the ice dispenser
or on the bucket. They may get hurt.
- Be sure not to put your hand or any object into
the ice chute. It may cause personal injury or
damage mechanical parts.
Removing residual matter inside the
water supply line after installing fi lter.
1. Turn ON the main water supply.
2. Press the Water button and push the Dispenser
Lever.
3. Flush 1 gallons of water through the filter before
use. (Flush approximately 6 minutes.) This will
clean the water supply system and remove air
from the lines.
Figure 1
Figure 1
Figure 2
Figure 2
Figure 3
Figure 3
Ice Chute
Ice Chute
Ice
Ice
Water
Water
Ice maker
Ice maker
1
1
Test button
Test button
Check the
Check the
water level
water level
2
2
CAUTION
CAUTION
operating _13
02 OPERATING
( 4 )
( 4 )
Lighting/
Lighting/
Hold 3
Hold 3
sec for
sec for
C
C
F
F
Touching the Lighting button turns on the
Dispenser LED lamp (under the display)
in continuous mode so that it stays on
continuously. The button also lights up. If
you want the Dispenser lamp to come on
only when some one uses the dispenser,
press the Lighting button to turn the
continuous mode off.
Touch and hold this button for 3 seconds
to switch the temperature units between
°C and °F
( 5 )
( 5 )
Fridge
Fridge
(Hold 3 sec
(Hold 3 sec
for Power
for Power
Cool)
Cool)
Touch this button to set the Fridge
temperature.
You can set the temperature between 1°C
and 7°C.
Touch and hold the this button for 3
seconds to decrease the time needed to
cool products in the Refrigerator. This can
be helpful if you need to cool easily spoiled
items quickly or if the temperature in the
fridge has warmed dramatically
(For example, if the door was left open).
( 6 )
( 6 )
Ice Off
Ice Off
(Hold 3 sec
(Hold 3 sec
for child
for child
lock)
lock)
If you don’t want to make more ice, touch
this button. Also, pressing and holding this
button for 3 second locks the display panel
and dispenser buttons so the buttons can
not be used. The Child Lock icon lights up
to indicate you’ve activated the Child Lock
function.
(7)
(7)
Ice Type
Ice Type
Touch this button to select your desired
ice type. Cubed and crushed ice modes
alternate each time you press the Ice Type
button.
Note that when you push the Ice Type
button, you turn the Water dispenser off.
USING THE CONTROL PANEL
( 1 )
( 1 )
Energy
Energy
Saver
Saver
Touching this button turns Energy Saver
mode on and off. When you turn Energy
Saver on, the Energy Saver icon lights up.
Turn Energy Saver off, and the icon goes
off. The Energy Saver function turns on
automatically when power is supplied to
the refrigerator.
If condensation or water drops appear on
the doors, turn the Energy Saver mode off.
( 2 )
( 2 )
Freezer
Freezer
(Hold 3 sec
(Hold 3 sec
for Power
for Power
Freeze)
Freeze)
Touch this button to set the Freezer
temperature.
You can set the temperature between
-14°C and -23°C.
Touch and hold this button for 3 seconds
to decrease the time needed to freeze
products in the Freezer. It can be helpful
if you need to freeze easily spoiled items
quickly or if the temperature in the Freezer
has warmed dramatically (For example, if
the door was left open).
( 3 )
( 3 )
Alarm /
Alarm /
Hold 3
Hold 3
sec for
sec for
Filter
Filter
Reset
Reset
This button serves two purposes:
1) To turn the door open alarm on
and off.
If the door alarm is set to On, an alarm
beeps if any refrigerator door is left open
for more than three minutes. The beeping
stops when you close the door. The door
alarm function is pre-set to On in the
factory. You can turn it off by touching and
then releasing this button. You can turn
it back on in the same fashion. The icon
lights up when the function is on.
2) After you replace the water filter,
Touch and hold this button for 3
seconds to reset the water filter
life indicator.
operating the SAMSUNG side-
by-side refrigerator
9
10
1
2
3
7
4
5
6
8
14_ operating
Controlling the Freezer temperature
You can set the Freezer temperature between -23°C
and -14°C to suit your particular needs. Touch
the Freezer button repeatedly until the desired
temperature is shown in the temperature display.
The temperature will move 1°C degrees with each
Touch as follows: -20°C -21°C -22°C -23°C
-14°C -15°C -16°C -17°C -18°C
-19°C -20°C. Keep in mind that foods such as ice
cream can melt at -15°C. The temperature display
will move sequentially from -23°C to -14°C.
Controlling the fridge temperature
You can set the fridge temperature between 7°C and
1°C to suit your particular needs. Touch the Fridge
button repeatedly until the desired temperature is
shown in the temperature display. The temperature
will move 1°C degrees with each touch as follows:
3°C 2°C 1°C 7°C 6°C 5°C 4°C
3°C. The temperature control process for the Fridge
works just like the Freezer process. Touch the Fridge
button to set your desired temperature. After a few
seconds, the Fridge will begin adjusting towards the
newly set temperature. This will be refl ected in the
digital display.
(8)
(8)
Water
Water
Touch this button to dispense water. Note
that you cannot dispense water and ice
simultaneously.
The Water dispenser turns off when you
press the Ice Type button.
( 9 )
( 9 )
Ice Off
Ice Off
When you touch the Ice Off button (
), the Ice Off icon lights and the Ice Maker
stops making ice.
We recommend you stop ice
making if the following occur:
- There is enough ice in the ice bucket.
- You want to save water and energy.
- Water is not being supplied to the
refrigerator.
If the ice maker function is
ON, and the water line is not
connected, there will be a water
valve noise from back of the unit.
Press the Ice Off (Hold 3sec for
child lock) button (
) for less
than 3 seconds until the Ice Off
Indicator (
) illuminates.
If you do not touch any button, the freezer and fridge
temperature indicator turn off in a few seconds.
If you touch any button, the display lights up again.
( 10 )
( 10 )
Filter
Filter
Water fi lter usage
The Water Filter icon lights in red when you
need to change the water fi lter.
This occurs after you use about 300
gallons of water (which usually takes
about 6 months). The icon will blink red for
several seconds when you open or close
the door.
CONTROLLING THE
TEMPERATURE
Basic temperature of Freezer and
Refrigerator Compartments
The basic temperature and recommended
temperatures of the Freezer and Refrigerator
Compartments are -20°C and 3°C respectively.
If the temperature of the Freezer or Refrigerator
Compartments are too high or low, adjust the
temperature manually.
Recommend Temp (Freezer) : -20°C
Recommend Temp (Freezer) : -20°C
Recommend Temp (Fridge) : 3
Recommend Temp (Fridge) : 3
°C
°C
operating _15
02 OPERATING
In case ice doesn’t come out, pull out the ice
bucket and press the test button located on the
right side of ice maker.
Do not press the test button continuously when
the tray is filled with ice or water. Water may
overflow or ice may jam the bucket.
When you press the Test button, you will
hear the refrigerator chime (ding-dong).
When the chime sounds, release the Test
button.
The chime sounds automatically again to let you
know the ice maker is working well.
If a power failure occurs, ice cubes may melt
then freeze together when the power comes
back on, causing the dispenser to be out of
order.
To prevent this problem, after a power failure, pull
out the ice bucket and discard the residual ice or
water.
After you dump the ice from the ice bucket,
you should press the dispenser lever once
with the ‘ICE CUBED’ or ‘CRUSHED’ function
ON.
The ice maker will make new ice faster after you
return the ice bucket to the refrigerator.
Do not put your fingers, hands or any
other unsuitable objects in the chute or
ice-maker bucket. It may result in personal
injury or material damage.
Use only the ice maker provided with the
refrigerator.
The water supply to this refrigerator must be
installed/connected by a suitably qualified person
and connect to a potable water supply only.
For the the ice maker to operate properly, the water
pressure must be between 20 and 125 psi.
- The temperature of the Freezer or Fridge
may rise when you open the doors too
frequently, or if a large amount of warm or
hot food is placed inside.
- This may cause the digital display to blink. Once
the Freezer and Fridge temperatures return to
their normal set temperatures, the blinking will
stop.
- If the blinking continues, you may need to “reset”
the Refrigerator. Try unplugging the appliance,
wait for around 10 minutes, and then plug the
power cord back in.
- If there is a communication error between the
Display and Main Controller, the Convertible
Display light may blink. If the blinking continues
for a long period of time, please contact a
Samsung Electronics Service Center.
HOW TO USE THE DISPENSER
Push the appropriate Ice Type button
or the Water button to select what
you want dispensed.
Press the Ice Type button to select
the type of ice you want. Place your
cup under the ice outlet and push
gently against the dispenser lever.
Make sure the glass is in line with
the dispenser to prevent the ice
from bouncing out. When you select
Cubed Ice after using the Crushed
Ice feature, a small amount of
residual crushed ice might be produced.
Please wait 2 seconds before removing the
glass under the dispenser to prevent spills.
If the Refrigerator door opens, the Dispenser does
not work.
Do not pull the lever out. You could damage or
break the lever’s spring.
To clean the ice bin/bucket, wash with a mild
detergent, rinse well, and dry thoroughly it. Do
not use harsh or abrasive cleaners or solvents.
NO ICE
NO ICE
Select this if you want to turn
Select this if you want to turn
ice maker off
ice maker off
CAUTION
CAUTION
CAUTION
WARNING
16_ operating
When “Thaw” ends, food is in a half-frozen state,
making it easy to cut for cooking. In addition, when
Thaw” ends, the CoolSelect Zone™ Drawer returns
to the original “Chill” condition. To cancel this
function mid-cycle, just press any button besides
Thaw.
Here are the approximate thawing times of meat
and fi sh by weight (and based on a 25.4mm (1in.)
thickness). This chart represents the total weight of
food in the CoolSelect Zone™ Drawer.
THAW TIME WEIGHT
4hours 363g (0.8Ib)
6hours 590g (1.3Ib)
10hours 771g (1.7Ib)
12hours 1000g (2.2Ib)
Quick Cool
You can use the “Quick Cool” operation with the
CoolSelect Zone™ Drawer to quickly cool 1~3
canned beverages in about an hour. When the
“Quick Cool” process ends, the CoolSelect Zone™
Drawer automatically returns to the previously set
temperature.
To cancel this operation, press the Quick Cool
button again and the CoolSelect Zone™ Drawer
returns to the previously set temperature.
Fresh
When “Cool” is selected, the temperature in the
CoolSelect Zone™ Drawer will be the same as the
overall temperature setting of the refrigerator. The
drawer digital panel shows the same temperature
as that of the refrigerator display panel. Since the
“Cool” function mimics the refrigerator temperature,
you have extra general storage space.
Depending on the size and thickness of the
meat or fi sh, thawing times may vary.
When “Thaw” is in operation, any items that
you do not want affected should be moved
out of the drawer.
If you have a
long vacation
or business trip
and won’t use
the water or ice
dispensers, close
the water valve.
- Otherwise, water
leakage may occur.
When you have not
used the Ice maker for
a while, or you have
opened the Freezer door frequently, the Ice may
stick together. If this has occurred, empty the ice
bucket or break up the ice with a wood kitchen
tool. Do not use sharp items such as knives or
forks.
When the bucket is removed, there may still
be some residual ice in the ice maker that the
icemaker can release.
If ice does not
dispense, pull
out the icemaker
cover and press
test button
located on the ice
maker.
Do not press the test
button continuously
when the tray is filled with ice or water. Water
may overflow or the ice may jam the icemaker or
dispenser.
USING THE COOLSELECT
ZONE™ DRAWER
The CoolSelect Zone™ Drawer is designed to make
your busy life just a little bit easier.
Chill
When “Chill” is selected, the temperature of
the CoolSelect Zone™ Drawer is kept at -1°C,
regardless of the overall temperature setting of the
refrigerator. This feature also helps keep meat or fi sh
fresh for longer.
Thaw
When “Thaw” is selected, warm and cold air is
alternately blown into the CoolSelect Zone™ Drawer.
Depending on the weight of the frozen food, you
can select a 4 hrs, 6 hrs, 10 hrs, and 12 hrs thawing
time.
Ice Chute
Ice Chute
Ice Bucket
Ice Bucket
Ice-Maker Cover
Ice-Maker Cover
CAUTION
Test button
Test button
CAUTION
operating _17
02 OPERATING
5. Ice Bucket (Freezer)
Remove the Icemaker Bucket
by lifting up and pulling it out
slowly.
Grip the handle as shown
in the figure.
Lift the low part slightly.
Take the ice bucket out
slowly.
Do not use excessive force when removing
the drawer cover.
You can break the cover and cause injury.
Before removing any accessories, make sure
that no food is in the way.
When possible, remove the food altogether to
reduce the risk of accidents.
CHANGING THE INTERIOR
LIGHTS
Do not disassemble or replace the LED type
Lighting.
To change the LED Type Lighting, contact a
Samsung service center.
TO IMPROVE THE COOLING
PERFORMANCE
If the cold air
outlet is blocked
by food items, the
cold air cannot
penetrate the entire
compartment and
will be unable
to freeze the
food effi ciently
which results in
a degraded cooling
performance.
In particular, there is load
limit at the top of the
freezing compartment.
Please do not put food
items above this limit.
CLEANING THE REFRIGERATOR
Do not use Benzene, Thinner or Clorox™, or
car detergent to clean the Refrigerator.
They may damage the surface of the
appliance and can create a risk of fi re.
Do not spray the refrigerator with water while
it is plugged in, as it may cause an electric
shock.
REMOVING THE FREEZER/
FRIDGE ACCESSORIES
Cleaning and rearranging the interior of the freezer
is a snap.
1. Shelves (Freezer/Fridge)
Pull the shelf out as far
as it goes and then lift up
and remove it.
2. DOOR BIN
Remove the Door Bin
by holding it with both
hands, and then gently
lift it up.
3. DRAWER
Remove the Drawer by
pulling it out and lifting it
up slightly.
4. Drawer Cover
Pull the cover out as far
as it goes, and then lift up
and remove it.
CAUTION
WARNING
CAUTION
Cold air outlet
Cold air outlet
Load limit in
Load limit in
the freezing
the freezing
compartment
compartment
18_ operating
water filter. The color of indicator changes from
red to light off.
A newly installed water fi lter cartridge may
cause water to briefl y spurt from the water
dispenser. This is due to air getting into the
line. It should pose no problem to operation.
Removing residual matter inside the
water supply line after installing a
new fi lter
1. Press the Water button, and then push the
Dispenser Lever with a cup or glass.
2. Flush 1 gallon of water through the filter, one
cup or glass at a time. (Flush approximately 6
minutes.) This will clean the water supply system
and remove air from the lines.
- Additional flushing may be required in some
households.
3. Open the refrigerator door and make sure there
are no water leaks coming from the water filter.
Reverse Osmosis Water Supply
IMPORTANT : The pressure of the water supply
coming out of a reverse osmosis system going to
the water inlet valve of the refrigerator needs to be
between 35 and 120 psi (241 and 827 kPa).
If a reverse osmosis water fi ltration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs to be
a minimum of 40 to 60 psi (276 to 414 kPa.)
If the water pressure to the reverse osmosis system
is less than 40 to 60 psi (276 to 414 kPa):
Check to see whether the sediment filter in the
reverse osmosis system is blocked. Replace the
filter if necessary.
Allow the storage tank on the reverse osmosis
system to refill after heavy usage.
If your refrigerator has a water filter, it may
further reduce the water pressure when used
in conjunction with a reverse osmosis system.
Remove the water filter.
If you have questions about your water pressure, call
a licensed, qualifi ed plumber.
Ordering replacement fi lters
To order more water fi lter cartridges, contact your
authorized Samsung dealer.
CHANGING THE WATER FILTER
To reduce risk of water damage to your
property DO NOT use generic brands of
water fi lers in your SAMSUNG Refrigerator.
USE ONLY SAMSUNG BRAND WATER
FILTERS.
SAMSUNG is not legally responsible for any
damage, including, but not limited to property
damage caused by water leakage from the use of a
generic water fi lter.
SAMSUNG Refrigerators are designed to work
ONLY WITH SAMSUNG Water Filters.
The “Filter Indicator” light lets you know when it is
time to change your water fi lter cartridge. To give
you preparation time to get a new fi lter, the red light
will come on just before the capacity of the current
lter runs out. Changing the fi lter on time provides
you with the freshest, cleanest water from your
fridge.
To change the water fi lter, follow these steps:
1. Turn the water filter 90˚
counter-clockwise.
2. Pull the water filter from
the filter housing.
3. Insert new water filter
inside the filter housing.
4. Turn the new water filter
90˚ clockwise.
5. Press the “Alarm/hold 3 sec for Filter Reset
button (
) for about 3 seconds to reset the
WARNING
troubleshooting _19
03 TROUBLESHOOTING
troubleshooting
PROBLEM SOLUTION
The refrigerator does
not work at all or it does
not chill sufficiently.
Check that the power plug is properly connected.
Is the temperature control on the display panel set to the correct temperature?
Try setting it to a lower temperature.
Is the refrigerator in direct sunlight or located too near a heat source?
Is the back of the refrigerator too close to the wall and therefore keeping air from
circulating?
The food in the fridge is
frozen.
Is the temperature control on the display panel set to the correct temperature?
Try setting it to a warmer temperature.
Is the temperature in the room very low?
Did you store the food with a high water content in the coldest part of the fridge?
You hear unusual noises
or sounds.
Check that the refrigerator is level and stable.
Is the back of the refrigerator too close to the wall and therefore keeping air from
circulating?
Was anything dropped behind or under the refrigerator?
A “ticking” sound is heard from inside the refrigerator. This is normal and occurs
because various accessories are contracting or expanding in relation to the
temperature of the refrigerator interior.
The front corners of
the appliance are hot
and condensation is
occurring.
Some heat is normal as anti-condensators are installed in the front corners of the
refrigerator to prevent condensation.
Is the refrigerator door ajar? Condensation can occur when you leave the door
open for a long time.
Ice is not dispensing.
Did you wait at least 12 hours after installation of the water supply line before
making ice?
Is the water line connected and the shut-off valve open?
Did you manually stop the ice making function? Make sure Ice Type is set to
Cubed or Crushed.
Is there any ice blocked within the ice maker bucket?
Is the freezer temperature too warm? Try setting the freezer temperature lower.
You can hear water
bubbling in the
refrigerator.
This is normal. The bubbling comes from the refrigerant coolant liquid circulating
through the refrigerator.
There is a bad smell in
the refrigerator.
Has a food item spoiled?
Make sure that strong smelling food (for example, fish) is wrapped so that it is
airtight.
Clean out your freezer periodically and throw away any spoiled or suspect food.
Frost forms on the walls
of the freezer.
Is the air vent blocked? Remove any obstructions so air can circulate freely.
Allow sufficient space between the foods stored for efficient air circulation.
Is the freezer door closed properly?
Water dispenser is not
functioning.
Is the water line connected and the shut-off valve open?
Has the water supply line tubing been crushed or kinked? Make sure the tubing
is free and clear of any obstruction.
Is the water tank frozen because the refrigerator temperature is too low? Try
selecting a warmer setting on the main display panel.
Ambient Room Temperature Limits
This refrigerator is designed to operate in ambient temperatures specifi ed by its
temperature class marked on the rating plate.
Class Symbol
Ambient Temperature range (°C)
IEC 62552 (ISO 15502) ISO 8561
Extended Temperate SN +10 to +32 +10 to +32
Temperate N +16 to +32 +16 to +32
Subtropical ST +16 to +38 +18 to +38
Tropical T +16 to +43 +18 to +43
Internal temperatures may be affected by such factors as the location of the fridge/freezer, ambient
temperature and the frequency with which you open the door. Adjust the temperature as required to
compensate for these factors.
English
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic
accessories (e.g. charger, headset, USB cable) should not be disposed of with other household
waste at the end of their working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate these items from other types of waste
and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their lo-
cal government of ce, for details of where and how they can take these items for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product and its electronic accessories should not be mixed with other commercial
wastes for disposal.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
COUNTRY CALL WEBSITE
MENA
U.A.E 800-SAMSUNG (800 - 726 7864)
www.samsung.com/ae/support (English)
www.samsung.com/ae_ar/support (Arabic)
OMAN 800-SAMSUNG (800 - 726 7864)
KUWAIT 183-CALL (183-2255)
BAHRAIN 8000-GSAM (8000-4726)
QATAR 800-CALL (800-2255)
EGYPT
08000-726786
16580
www.samsung.com/eg/support
ALGERIA 021 36 11 00 www.samsung.com/n_africa/support
PAKISTAN 0800-Samsung (72678) www.samsung.com/pk/support
TUNISIA 80-1000-12 www.samsung.com/n_africa/support
JORDAN
0800-22273
06 5777444
www.samsung.com/Levant/support (English)
SYRIA 18252273 www.samsung.com/Levant/support (English)
MOROCCO 080 100 2255 www.samsung.com/n_africa/support
SAUDI ARABIA 920021230
www.samsung.com/sa/support
www.samsung.com/sa_en/support (English)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Samsung RS30GKASL Manuel utilisateur

Catégorie
Frigos
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues