Samsung RSH5ZLMR Manuel utilisateur

Catégorie
Frigos
Taper
Manuel utilisateur
Refrigerator
user manual
imagine the possibilities
Thank you for purchasing a Samsung product.
English
Free Standing Appliance
This manual is made with 100 % recycled paper.
DA68-02912A-02.indb 1DA68-02912A-02.indb 1 14. 7. 18.  8:2114. 7. 18.  8:21
02_ safety information
safety information
SAFETY INFORMATION
• Before operating the appliance, please read
this manual thoroughly and retain it at a safe
place near the appliance for your future reference.
• Use this appliance only for its intended
purpose as described in this instruction
manual. This appliance is not intended for use
by persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning
and user maintenance shall not be made by
children without supervision.
• Warnings and Important Safety Instructions
in this manual do not cover all possible
conditions and situations that may occur. It
is your responsibility to use common sense,
caution, and care when installing, maintaining,
and operating your appliance.
• Because these following operating instructions
cover various models, the characteristics of
your refrigerator may differ slightly from those
described in this manual and not all warning
signs may be applicable. If you have any
questions or concerns, contact your nearest
service center or find help and information
online at www.samsung.com.
Important safety symbols and
precautions :
WARNING
Hazards or unsafe practices that
may result in severe personal
injury or death.
CAUTION
Hazards or unsafe practices that
may result in minor personal
injury or property damage.
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions carefully.
Unplug the power plug from the
wall socket.
Make sure the machine is grounded
to prevent electric shock.
Call the contact center for help.
Note.
These warning signs are here to prevent
injury to you and others.
Please follow them carefully.
After reading this section, keep it in a safe
place for future reference.
CE Notice
This product has been determined to be in
compliance with the Low Voltage Directive(2006/95/
EC), the Electromagnetic Compatibility Directive
(2004/108/EC), RoHS Directive (2011/65/EU),
Commission Delegated Regulation (EU) No
1060/2010 and the Eco-Design Directive(2009/125/
EC) implemented by Regulation (EC) No 643/2009 of
the European Union. (For products sold in European
Countries only)
SEVERE WARNING SIGNS
FOR TRANSPORTATION
AND SITE
• When transporting and installing the
appliance, care should be taken to ensure
that no parts of the refrigerating circuit are
damaged.
- Refrigerant leaking from the pipe work could
ignite or cause an eye injury. If a leak is detected,
avoid any naked flames or potential sources of
ignition and air the room in which the appliance is
standing for several minutes.
In order to avoid the creation of a flammable
gas-air mixture if a leak in the refrigerating
circuit occurs, the size of the room in which the
appliance may be sited depends on the amount
of refrigerant used.
Never start up an appliance showing any signs
of damage. If in doubt, consult your dealer. The
WARNING
DA68-02912A-02.indb Sec2:02DA68-02912A-02.indb Sec2:02 14. 7. 18.  8:2114. 7. 18.  8:21
safety information _03
room where the refrigerator will be sited must be
1 m³ in size for every 8 g of R-600a refrigerant
inside the appliance. The amount of refrigerant
in your particular appliance is shown on the
identification plate inside the appliance.
SEVERE WARNING SIGNS
FOR INSTALLATION
Do not install the refrigerator in a damp place
or place where it may come in contact with
water.
- Deteriorated insulation of electrical parts may
cause an electric shock or fire.
Do not place this refrigerator in direct sunlight or
expose to the heat from stoves, room heaters or
other appliance.
Do not plug several appliances into the same
multiple power board.
The refrigerator should always be plugged into
its own individual electrical which has a voltage
rating that matched the rating plate.
- This provides the best performance and also
prevents overloading house wiring circuits, which
could cause a fire hazard from overheated wires.
If the wall socket is loose, do not insert the
power plug.
- There is a risk of electric shock of fire.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
Do not bend the power cord excessively or
place heavy articles on it.
Do not use aerosols near the refrigerator.
- Aerosols used near the refrigerator may cause
an explosion or fire.
• This refrigerator must be properly installed
and located in accordance with the manual
before it is used.
Connect the power plug in proper position with
the cord hanging down.
- If you connect the power plug upside down, wire
can get cut off and cause fire or electric shock.
Make sure that the power plug is not squashed
or damaged by the back of the refrigerator.
When moving the refrigerator, be careful not to
roll over or damage the power cord.
- This constitutes a fire hazard.
The appliance must be positioned so that the
plug is accessible after installation.
• The refrigerator must be grounded.
- You must ground the refrigerator to prevent
any power leakages or electric shocks caused by
current leakage from the refrigerator.
Never use gas pipes, telephone lines or other
potential lightening rods as ground.
- Improper use of the ground plug can result in
electric shock.
• If the power cord is damaged, have it
replaced immediately by the manufacturer or
its service agent.
The fuse on the refrigerator must be changed by
a qualified technician or service company.
- Failing to do so may result in electric shock or
personal injury.
CAUTION SIGNS FOR
INSTALLATION
• Keep ventilation opening in the appliance
enclosure or mounting structure clear of
obstruction.
Allow the appliance to stand for 2 hours after
installation.
SEVERE WARNING SIGNS
FOR USING
Do not insert the power plug with wet
hands.
• Do not store articles on the top of the appliance.
- When you open or close the door, the articles
may fall and cause personal injury and/or material
damage.
Do not put items filled with water on the
refrigerator.
- If spilled, there is a risk of fire or electric shock.
• Do not let children hang on the door.
- Failure to do so may cause serious personal
injury.
Do not leave the doors of the refrigerator open
while the refrigerator is unattended and do not let
children enter inside of the refrigerator.
- There is a risk of children entrapment and serious
personal injury because of low temperature.
Never put fingers or other objects into the
dispenser hole.
- Failure to do so may cause personal injury or
material damage.
Do not store volatile or flammable substances
such as benzene, thinner, alcohol, ether or LP
gas in the refrigerator.
- The storage of any of such products may cause
explosions.
WARNING
CAUTION
WARNING
DA68-02912A-02.indb Sec2:03DA68-02912A-02.indb Sec2:03 14. 7. 18.  8:2114. 7. 18.  8:21
04_ safety information
• Do not store low temperature-sensitive
pharmaceuticals products, scientific
materials or other low temperature-sensitive
products in the refrigerator.
- Products that require strict temperature controls
must not be stored in the refrigerator.
Do not place or use electrical appliance inside
the refrigerator, unless they are of a type
recommended by the manufacturer.
Do not use a hair dryer to dry the inside of the
refrigerator. Do not place a lighted candle in the
refrigerator for removing bad odors.
- This may result in electric shock or fire.
Do not touch the inside walls of the freezer or
products stored in the freezer with wet hands.
- This may cause frostbite.
Do not use mechanical devices or any other
means to accelerate the defrosting process,
other than those recommended by the
manufacturer.
• Do not damage the refrigerant circuit.
This product is intended only for the
storage of food in a domestic environment.
Bottles should be stored tightly together so that
they do not fall out.
If a gas leak is detected, avoid any naked flames
or potential sources of ignition and air the room
in which the appliance is standing for several
minutes.
Use only the LED Lamps provided by
manufacturer or service agents.
Children should be supervised to ensure that
they do not play with and/or climb into the
appliance.
Do not disassemble or repair the
refrigerator by yourself.
- You run risk of causing a fire, malfunction and/
or personal injury. In case of malfunction, please
contact your service agents.
• If the appliance generates a strange noise,
a burning or smell or smoke, unplug the
power plug immediately and contact your nearest
service center.
- Failing to do so may result in electric or fire
hazards. Keep ventilation opening in the
appliance enclosure or mounting structure clear
of obstruction.
If you experience difficulty when changing the
light, contact service agents.
If the products equipped with LED Lamp, do
not disassemble Lamp Cover and LED Lamp by
yourself.
- Please contact your service agents.
If any dust or water is in refrigerator, pull
out power plug and contact your Samsung
Electronics service center.
- There is a risk of fire.
CAUTION SIGNS FOR
USING
• To get best performance of product,
- Do not place foods too closely in front of
the vents at the rear of the appliance as it can
obstruct free air circulation in the refrigerator
compartment.
-
Wrap the food up properly or place it in airtight
containers before put it into the refrigerator.
Do not place carbonated or fizzy drinks in the
freezer compartment. Do not put bottles or glass
containers in the freezer.
- When the contents freeze, the glass may break
and cause personal injury and property damage.
Do not change the functionality of or modify the
refrigerator.
- Changes or modifications may result in personal
injury and/or property damage. Any changes or
modifications performed by a 3rd party on this
completed appliance is neither covered under
Samsung warranty service, nor is Samsung
responsible for safety issues and damages that
result from 3rd party modifications.
• Do not block air holes.
-
If the air holes are blocked, especially with a plastic
bag, the refrigerator can be over cooled. If this
cooling period lasts too long, the water filter may
break and cause water leakage.
- Do not put any newly introduced food for
freezing near to already food.
Please observe maximum storage times and
expiry dates of frozen goods.
Fill water tank, ice tray, water cubes only with
potable water.
Use only the ice maker provided with the
refrigerator.
The water supply to this refrigerator must only
be installed/connected by a suitably qualified
person and connect to a potable water supply
only.
In order to operate the ice maker properly, water
pressure of 138 ~ 862 kPa(1.4~8.8kgf/cm
3
) is
required.
Do not apply strong shock or excessive force
CAUTION
DA68-02912A-02.indb Sec2:04DA68-02912A-02.indb Sec2:04 14. 7. 18.  8:2114. 7. 18.  8:21
safety information _05
onto the surface of glass.
- Broken glass may result in a personal injury and/
or property damage.
CAUTION SIGNS
FOR CLEANING AND
MAINTENANCE
Do not directly spray water inside or
outside the refrigerator.
- There is a risk of fire or electric shock.
Do not spray inflammable gas near the
refrigerator.
- There is a risk of explosion or fire.
Do not spray cleaning products directly on the
display.
- Printed letters on the display may come off.
Remove any foreign matter or dust from the
power plug pins. But do not use a wet or damp
cloth when cleaning the plug, remove any foreign
material or dust from the power plug pins.
- Otherwise there is a risk of fire or electric shock.
Never put fingers or other objects into the
dispenser hole and ice chute.
- It may cause personal injury or material damage.
Unplug the refrigerator before cleaning and
performing maintenance.
SEVERE WARNING SIGNS
FOR DISPOSAL
• Ensure that none of the pipes on the
back of the appliance are damaged prior to
disposal.
R-600a or R-134a is used as a refrigerant.
Check the compressor label on the rear of
the appliance or the rating label inside the
refrigerator to see which refrigerant is used for
your refrigerator. When this product contains
flammable gas (Refrigerant R-600a), contact your
local authority in regard to safe disposal of this
product. Cyclopentane is used as a insulation
blowing gas. The gases in insulation material
require special disposal procedure. Please
contact your local authorities in regard to the
environmentally safe disposal of this product.
Ensure that none of the pipes on the back of the
appliances are damaged prior to disposal. The
pipes shall be broke in the open space.
If the appliance contains iso-butane refrigerant
(R-600a), a natural gas with high environmental
compatibility that is, however, also combustible.
When transporting and installing the appliance,
care should be taken to ensure that no parts of
the refrigerating circuit are damaged.
When disposing of this product or other
refrigerators, remove the door/door seals, door
latch so that small children or animals cannot
become trapped inside. Leave the shelves in
place so that children may not easily climb inside.
Children should be supervised to ensure that
they do not play with the old appliance.
Please dispose of the packaging material for this
product in an environmentally friendly manner.
ADDITIONAL TIPS FOR PROPER
USAGE
In the event of a power failure, call the local office
of your Electricity Company and ask how long it is
going to last.
- Most power failures that are corrected within
an hour or two will not affect your refrigerator
temperatures. However, you should minimize the
number of door openings while the power is off.
- Should the power failure last more than 24 hours,
remove all frozen food.
If keys are provided with the refrigerator, the
keys should be kept out of the reach of children
and not in vicinity of the appliance.
The appliance might not operate consistently
(possibility of temperature becoming too warm
in refrigerator) when sited for an extended period
of time below the cold end of the range of
temperature for which the refrigerating appliance
is designed.
Do not store food which spoils easily at low
temperature, such as bananas, melons.
Your appliance is frost free, which means there
is no need to manually defrost your appliance,
as this will be carried out automatically.
Temperature rising during the defrost can
comply with ISO requirement. But if you want
to prevent an undue rise in the temperature of
the frozen food while defrosting the appliance,
please wrap the frozen food in several layers of
newspaper.
Any increase in temperature of frozen food
during defrosting can shorten its storage life.
CAUTION
WARNING
DA68-02912A-02.indb Sec2:05DA68-02912A-02.indb Sec2:05 14. 7. 18.  8:2114. 7. 18.  8:21
06_ safety information
contents
SETTING UP YOUR SIDE-BY-SIDE REFRIGERATOR ···································7
OPERATING THE SAMSUNG SIDE-BY-SIDE REFRIGERATOR ····················16
TROUBLESHOOTING ····················································································· 22
Saving Energy Tips
- Install the appliance in a cool, dry room with
adequate ventilation.
Ensure that it is not exposed to direct sunlight and
never put it near a direct source of heat (radiator, for
example).
- Never block any vents or grilles on the appliance.
- Allow warm food to cool down before placing it in
the appliance.
- Put frozen food in the refrigerator to thaw.
You can then use the low temperatures of the
frozen products to cool food in the refrigerator.
- Do not keep the door of the appliance open for too
long when putting food in or taking food out.
The shorter time for which the door is open, the less
ice will form in the freezer.
- Clean the rear of the refrigerator regularly. Dust
increases energy consumption.
- Do not set temperature colder than necessary.
- Ensure suffi cient air exhaust at the refrigerator base
and at the back wall of the refrigerator.
Do not cover air vent openings.
- Allow clearance to the right, left, back and top when
installing.
This will help reduce power consumption and keep
your energy bills lower.
- For the most effi cient use of energy, please keep
the all inner fi ttings such as baskets, drawers,
shelves on the position supplied by manufacturer.
This appliance is intended to be used in
household and similar applications such as
- staff kitchen areas in shops, of ces and other
working environments;
- farm houses and by clients in hotels, motels and
other residential type environments;
- bed and breakfast type environments;
- catering and similar non-retail applications.
DA68-02912A-02.indb Sec2:06DA68-02912A-02.indb Sec2:06 14. 7. 18.  8:2114. 7. 18.  8:21
setting up _07
01 SETTING UP
CAUTION
setting up your side-by-side
refrigerator
GETTING READY TO INSTALL
THE REFRIGERATOR
Congratulations on the purchase of your Samsung
Side-By-Side Refrigerator. We hope you will enjoy the
many state-of-the-art features and ef ciencies that
this new appliance has to offer.
Selecting the best location for the
refrigerator
• Select a location with easy access to the water
supply.
• Select a location without direct exposure to
sunlight.
• Select a location with level (or nearly level) fl ooring.
• Select a location with enough space for the
refrigerator doors to open easily.
• Overall space required in use. Refer to drawing and
dimension as below.
• Please ensure that appliance can be moved freely
in the event of maintenance & service.
When moving your refrigerator
To prevent fl oor damage be sure the front levelling
legs are in the up position (above the fl oor). Refer to
‘Levelling the refrigerator’ in the manual (at page 11).
To protect the fi nish of the fl ooring, place the
protection sheet such as packing carton under the
refrigerator.
When installing, servicing or cleaning
behind the refrigerator, be sure to pull the
unit straight out and push back in straight
after fi nishing.
Leg
Screw Driver
50 mm
25 mm
at least 50 mm
at least 50 mm
130 º 130 º
1532 mm
950 mm
DA68-02912A-02.indb Sec4:07DA68-02912A-02.indb Sec4:07 14. 7. 18.  8:2114. 7. 18.  8:21
08_ setting up
REMOVING THE REFRIGERATOR
DOORS
If your entrance won’t allow the refrigerator to pass
easily through it, you can remove the doors.
1. Removing the Front Leg Cover
First, open both the freezer and refrigerator doors,
and then take off the front leg cover by removing the
three screws counter-clockwise.
Separating the Water Supply Line from
the Refrigerator
1. Remove the water line by pressing the coupler
1
and pulling the water line
2
away.
Do not cut the water line. Gently separate it from
the coupler.
2. Removing the freezer door
A few things to mention fi rst.
Make sure that you lift the door straight up so the
hinges are not bent or broken.
Be careful not to pinch the water tubing and wire
harness on the door.
Place doors on a protected surface to prevent
scratching or damage.
1. With the Freezer door closed, remove the upper
hinge cover
1
using a screwdriver, and then
disconnect the wires by gently pulling them apart
2
.
2. Remove hinge screws
3
and the ground screw
4
by turning counter-clockwise, and take off the
upper hinge
5
. Be careful that the door does not
fall on you as you are removing it
3. Next, remove the door from the lower hinge
6
by
carefully lifting the door straight up
7
.
Be careful not to pinch the water tubing and
wire harness on the door.
4. Remove the lower hinge
8
using a hex wrench.
2
1
3
4
5
7
6
1
2
DA68-02912A-02.indb Sec4:08DA68-02912A-02.indb Sec4:08 14. 7. 18.  8:2114. 7. 18.  8:21
setting up _09
01 SETTING UP
Removing the Fridge Door
1. With the door closed, remove the upper hinge
cover
1
using a screwdriver.
2. Remove hinge screws
2
and the ground screw
3
by turning counter-clockwise, and take off the
upper hinge
4
. Be careful that the door does not
fall on you as you are removing it
3. Remove the door from the lower hinge
5
by
lifting the door straight up
6
.
4. Remove the lower hinge
7
from the bracket
8
by gently lifting the lower hinge upwards.
REATTACHING THE
REFRIGERATOR DOORS
Once you have safely placed your refrigerator where
you plan for it to stay, it is time to put the doors back
on.
Reattaching the Freezer Door
1. Replace the freezer door by inserting the water
line
1
back into the lower corner of the door and
then into the hole on the lower hinge
2
.
Gently pull the water line back down so that it runs
straight, with no kinks or bends.
2. Insert the upper hinge shaft
3
into the hole on
the corner of the freezer door
4
.
Make sure the hinge is level between the upper
hinge hole
5
and the hole of the cabinet
6
and
reattach the hinge screws
7
and ground screw
8
by turning in a clockwise direction.
Reconnect the wires.
3. Place the front part of the upper hinge cover
9
on the front of the upper hinge
10
and reattach
with the screw.
4
2
3
1
4
5
6
7
8
3
1
2
10
9
DA68-02912A-02.indb Sec4:09DA68-02912A-02.indb Sec4:09 14. 7. 18.  8:2114. 7. 18.  8:21
10_ setting up
Reattaching the Fridge Door
1. Insert the lower hinge
1
back into the lower
hinge bracket
2
.
2. Fit the hole in the corner of the fridge door
3
over the lower hinge
4
.
3. Insert the upper hinge shaft
5
into the hole
on the hinge
6
. Make sure the hinge is level
between the upper hinge hole
7
and the hole on
the top of the cabinet
8
. Then, reattach hinge
screws
9
and the ground screw
10
by turning it
in a clock wise direction.
4. Place the front part of the upper hinge cover
11
on the front of the upper hinge
12
and reattach it
with the screw.
Reattaching the Water Supply Line
1. Insert the water line
2
into the coupler
1
.
2. The Water Line must be fully Inserted to the center
of transparent coupler to prevent water leakage
from the dispenser.
3. Insert the clip in the install pack and check that it
holds the line fi rmly.
Reattaching the Front Leg Cover
Before attaching the cover, check water
connector for leakage.
Replace the front leg cover by turning the three
screws clockwise, as shown in the fi gure.
1
2
1
2
3
4
12
11
Center of transparent
Center of transparent
coupler
coupler
clip A (1/4”)
clip A (1/4”)
(6.35 mm)
(6.35 mm)
DA68-02912A-02.indb Sec4:10DA68-02912A-02.indb Sec4:10 14. 7. 18.  8:2114. 7. 18.  8:21
setting up _11
01 SETTING UP
LEVELLING THE REFRIGERATOR
Now that the doors are back on the refrigerator, you
will want to make sure the refrigerator is level so you
can then make fi nal adjustments. If the refrigerator
is not level, it will not be possible to get the doors
perfectly even.
The front of the refrigerator is also adjustable.
When the Freezer door is lower than
the fridge
Insert a fl at-blade screwdriver into a notch on the
Leg, turn it clockwise or counter clockwise to level
the freezer.
When the Freezer door is higher than
the fridge
Insert a fl at-blade screwdriver into a notch on the
Leg, turn it clockwise or counter clockwise to level
the fridge.
Refer to the next section for the best way to
make very minor adjustments to the doors.
MAKING MINOR ADJUSTMENTS
TO THE DOORS
Remember, a level refrigerator is necessary for getting
the doors perfectly even. If you need help, review the
previous section on levelling the refrigerator.
In the process for adjusting both the doors is the
same. Open the doors and adjust them, one at a
time, as follows:
1. Unscrew the
nut
1
from the
lower hinge until
it reaches the
upper end of the
bolt
2
.
When you release the nut
1
, make sure that
you use the Allen wrench provided
3
to loosen
the bolt
2
in a counter-clockwise direction.
You should then be able to unscrew the nut
1
with your fi ngers.
2. Adjust the
height difference
between the
doors by turning
the bolt
2
clockwise
or counter clockwise
.
When you turn clockwise
, the door will
move up.
3. After adjusting
the doors, turn
the nut
1
clockwise
until it reaches
the lower end
of the bolt, then tighten the bolt again with the
wrench
3
to fi x the nut in place
1
.
If you do not secure the nut fi rmly, the bolt may
release.
Leg
Screw Driver
Screw Driver
Leg
Adjustment
part
When the door of the freezer
is higher than the fridge
3
2
1
Wrench
Bolt
Nut
3
2
Wrench
Bolt
3
2
1
Wrench
Bolt
Nut
DA68-02912A-02.indb Sec4:11DA68-02912A-02.indb Sec4:11 14. 7. 18.  8:2114. 7. 18.  8:21
12_ setting up
CHECKING THE WATER
DISPENSER LINE (OPTIONAL)
A water dispenser is just one of the helpful features
on your new Samsung refrigerator. To help promote
better health, the Samsung water fi lter removes
unwanted particles from your water. However, it
does not sterilize or destroy microorganisms. You
will need to purchase a water purifying system to do
that. In order for the icemaker to operate properly,
water pressure of 138 ~862 kPa is required. Under
normal conditions, a 170 cc paper cup can be fi lled
in 10 seconds. If the refrigerator is installed in an area
with low water pressure (below 138 kPa), you can
install a booster pump to compensate for the low
pressure. Make sure the water storage tank inside
the refrigerator is properly fi lled. To do this, press the
water dispenser lever until the water runs from the
water outlet.
Water Line installation Kits are included. You can
nd it in one of the freezer drawers.
The new hose-sets supplied with the appliance
are to be used and that old hose-sets should not
be reused.
INSTALLING THE WATER
DISPENSER LINE
For Interior model
Parts for water line Installation
Connecting to the water supply line
1. fi rst, shut off the main water supply line.
2. locate the nearest cold, drinking water line.
3. follow the Water line Installation Instructions in the
installation kit.
4. After connecting the water supply to the water
lter, turn your main water supply back on and
dispense about 1 L to clear and prime the water
lter.
Connecting the water line to the
refrigerator
1. Remove the dust cap from the water line on the
rear of the unit and fi t a compression nut from the
install kit.
2. Remove the water pipe from the install kit and fi t a
compression nut to one end.
3. Join the two pipes together using the compression
joint from the install kit ensuring that the joint is
water tight.
4. Join the other end of the install pipe to the main
water supply and turn on the water to check for
leaks.
Only connect the water line to a drinkable water
source.
If you have to repair or disassemble the water
line, cut off 6.5 mm of the plastic tubing to
make sure you get a snug, leak-free connection.
Before being used, the leakage in these
places should be examined
CAUTION
The water line must be connected
to the cold water pipe. If it is connected
to the hot water pipe, it may cause the
purifi er to malfunction.
1
Water line fi xer and screws
2
Pipe connector
3
Water line
4
Water Filter
Close Main
Close Main
Water pipe
Water pipe
Close Main
Close Main
Water pipe
Water pipe
NO GAP
NO GAP
Remove
Remove
cap
cap
Water Line
Water Line
from unit
from unit
Water Line
Water Line
from Kit
from Kit
No gap
No gap
Loosen a
Loosen a
CAUTION
DA68-02912A-02.indb Sec4:12DA68-02912A-02.indb Sec4:12 14. 7. 18.  8:2114. 7. 18.  8:21
setting up _13
01 SETTING UP
Samsung Warranty does not cover WATER LINE
INSTALLATION.
The cost of connection to a water supply is at the
customer expense, unless included in the delivery
charge (refer to the delivery agreement with the
seller)
Please contact Plumber or Authorised Installer for
the installation if needed.
If Water leakage occurs due to improper
installation, Please contact installer.
INSTALLING THE WATER
DISPENSER LINE
For Exterior model
Parts for water line Installation
Connecting to the water supply line
Connect the water pipe with coupler and tap.
1. Close the main water tap.
2. Connect coupler “A” to the tap.
select the location where the purifi er is to
install. (Model with the purifi er)
- If you wish to reassemble the water inlet and outlet
sides of the purifi er during purifi er installation, see
the reference illustration.
- Cut the water line attached to the purifi er to the
appropriate place after measuring the distance
between the purifi er and the cold water tap.
Water line fi xer and screws
Pipe connector
Water line
Purifi er lock-clip
Purifi er
CAUTION
The water line must be connected to the cold
water pipe. If it is connected to the hot water
pipe, it may cause the purifi er to malfunction.
WARRANTY INFORMATION
This water line installation is not covered by the
refrigerator or ice maker manufacturer’s warranty.
Follow these instructions carefully to minimise the risk of
expensive water damage.
Note:
If the coupler does not fi t on the current tap, go the
nearest authorised service dealer and purchase the right
couplers fi ttings.
DA68-02912A-02.indb Sec4:13DA68-02912A-02.indb Sec4:13 14. 7. 18.  8:2114. 7. 18.  8:21
14_ setting up
Replacement Instructions
1. Shut off water supply.
2. Note the Flow direction on the fi lter.
3. Insert water supply tube into the inlet side of the
lter until the tube stop.
4. After inserting tube, put together the clip strongly.
The Clip fi x the tube.
5. Turn on the water and check for leaks. If leaks
occur, repeat step 1,2,3,4. If leaks persist,
discontinue use and call your supporting dealer.
6. Flush fi lter for 5 minutes before use.
Remove any residual matter inside the
purifi er. (Model with the purifi er)
- Open the main water tap to check whether water
is running through the water tube on the water inlet
side of the purifi er.
- If water does not come out through the line, check
whether the tap is open.
- Leave the tap open until clean water is running
out and any residual matter that built up during
manufacturing has been removed.
Attach the purifi er lock-clip.
- Hold the purifi er lock-clip in the appropriate position
(under the sink for example) and fi x it tightly into
place where to screw.
Secure the purifi er in position.
- Fix the purifi er in position, as shown in the fi gure on
the right.
COUPLER “A”
TAP
COUPLER
SIDE OF
PURIFIER
WATER INLET
SIDE OF PURIFIER
LINE OUTLET
90 degree
PURIFIER WATER
CAUTION
Locking Clip
Locking Clip
Insert Locking Clip After
Insert Locking Clip After
tube seated
tube seated
WATER SUPPLY
INLET SIDE
PERMEAT
FLOW DIRECTION
Note : You must also ensure
that the cut is square
and not at any sort
of angle as this could
cause a leak
WATER LINE
PURIFIER
WATER
OUTLET SIDE
OF PURIFIER
PURIFIER LOCK-CLIP
WATER TUBE
PURIFIER LOCK-CLIP
PURIFIER
DA68-02912A-02.indb Sec4:14DA68-02912A-02.indb Sec4:14 14. 7. 18.  8:2114. 7. 18.  8:21
setting up _15
01 SETTING UP
Connect the water line to the
refrigerator.
- Remove the compressor cover of the refrigerator.
- Connect the water line to the valve, as shown in
the fi gure.
- When connected, check if there is any leakage.
If any, repeat the connection.
- Reattach the compressor cover of the refrigerator.
Secure the water line.
- Using clip ”A”, fi x the water
line to the wall (the back of
refrigerator).
- When the water line is
secure, make sure whether
the water line is not
excessively bent, pinched or
squashed.
Removing any residual matter inside
the water supply line after installing
lter.
1. Turn ON the main water supply & turn OFF the
valve to the water supply line.
2. Run water through the dispenser until the water
runs clear (approx. 1 L). This will clean the water
supply system and remove air from the lines.
3. Additional fl ushing may be required in some
households.
4. Open the refrigerator door and make sure there
are no water leaks coming from the water fi lter.
A newly installed water fi lter cartridge may cause
water to briefl y spurt from the water dispenser.
This is due to air getting into the line. It should
pose no problem to operation.
Check the amount of water supplied
to the ice tray.
1. Lift up the icemaker cover and gently pull out.
2. When you press the Test button for 3 seconds,
the ice cube container is fi lled with water from the
water supply tap. Check to make sure the amount
of water is correct (see the illustration below).
If the water level is too low, the ice cubes will be
small. This is a water pressure problem from with
in the main water pipes, not the refrigerator.
WATER LINE
INSTRUCTIONS
COMPRESSOR COVER OF
REFRIGERATOR
CONNECTION NUT
CLIP A
WATER LINE
Ice maker
1
Feeler Arm
2
Test button
Check the water level
DA68-02912A-02.indb Sec4:15DA68-02912A-02.indb Sec4:15 14. 7. 18.  8:2114. 7. 18.  8:21
16_ operating
operating the SAMSUNG
side-by-side refrigerator
OPERATING THE REFRIGERATOR
USING THE CONTROL PANEL /
DIGITAL DISPLAY
POWER
FREEZE
BUTTON
Speeds up the time needed
to freeze products in the
freezer. This can be helpful
if you need to quickly freeze
items that spoil easily or if the
temperature in the freezer
has warmed dramatically (For
example, if the door was left
open).
FREEZER
BUTTON
Press the Freezer button
to set the freezer to your
desired temperature, You can
set the temperature between
-14 °C (8 °F) and -25 ºC
(-14°F).
ICE
TYPE
BUTTON
Use this button to choose
Cubed, Crushed or to turn
the Ice feature off.
FILTER
CHANGE
BUTTON
When you change the fi lter,
press this button for 3
seconds to reset the fi lter
schedule.
VACATION
BUTTON
If you are going on vacation
or business trip or you do not
need to use the refrigerator,
press the Vacation button.
When you select vacation
button for fridge compartment
off, display LED of Vacation
will be on.
It is strongly requested
to remove foods in the
fresh-food compartment
and do not leave the
door open when you
select Vacation function.
CHILD
LOCK
FUNCTION
By pressing the Vacation
button and the Fridge button
simultaneously for 3 seconds,
all buttons will be locked. The
Water dispenser lever and
the Ice lever will not work
either. To cancel this function,
Press these two buttons for 3
seconds again.
FRIDGE
BUTTON
Press the Fridge button to
set the fridge to your desired
temperature.
You can set temperature
between 1 °C and 7 °C
(34°F and 45 °F).
When you use Power Freeze the energy
consumption of the refrigerator will increase.
Remember to turn it off when you don’t
need it and return the freezer to your original
temperature setting.
If you need to freeze large amount of food stuff,
activate Power Freeze function at least 24 hours
before.
5
6
7
1
3
4
2
COOLSELECT MODEL
DISPENSER MODEL
NORMAL MODEL
1
2
3
5
4
6
7
DA68-02912A-02.indb 2:16DA68-02912A-02.indb 2:16 14. 7. 18.  8:2114. 7. 18.  8:21
operating _17
02 OPERATING
CONTROLLING THE
TEMPERATURE
CONTROLLING THE FREEZER
TEMPERATURE
The freezer temperature can be set between -14°C
(8 °F) and -25 ºC (-14 °F) to suit your particular
needs. Press the Freezer button repeatedly until the
desired temperature is shown in the temperature
display. Keep in mind that foods like ice cream may
melt at -16 ºC (4 °F).
The temperature display will move sequentially from
-14 °C (8 °F) and -25 ºC (-14 °F). When the display
reaches -14 ºC (8 °F), it will begin again at -25 ºC
(-14 °F).
Five seconds after the new temperature is set the
display will again show the actual current freezer
temperature. However, this number will change as
the Freezer adjusts to the new temperature.
The top and bottom guards in the freezer of
this model are the two star sections, so the
temperature in two star sections are slightly
higher than other freezer compartment.
CONTROLLING THE FRIDGE
TEMPERATURE
The refrigerator temperature can be set between 7 ºC
(46 °F) and 1 ºC (34 °F) to suit your particular
needs. Press the Fridge button repeatedly until the
desired temperature is shown in the temperature
display. The temperature control process for the
Fridge works just like the Freezer process. Press the
Fridge button to set your desired temperature. After
a few seconds, the Fridge will begin tracking towards
the newly set temperature. This will be refl ected in the
digital display.
The temperature of the freezer or the refrigerator
may rise from opening the doors too frequently,
or if a large amount of warm or hot food is
placed in either side.
This may cause the digital display to blink.
Once the freezer and refrigerator return to their
normal set temperatures the blinking will stop.
If the blinking continues, you may need to “reset”
the refrigerator.
Try unplugging the appliance, wait about 10
minutes and then plug back in.
USING THE ICE AND COLD
WATER DISPENSER
Press the Ice Type button to select the type of ice
you want
Ice is made in cubes. When you select
“Crushed”, the icemaker grinds the ice cubes
into crushed ice.
Dispensing ice
Place your glass underneath the ice outlet and push
gently against the ice dispenser lever with your glass.
Make sure the glass is in line with the dispenser to
prevent the ice from bouncing out.
Using the Water Dispenser
Place a glass underneath the water outlet and
push gently against the water dispenser lever with
your glass. Make sure the glass is in line with the
dispenser to prevent the water from splashing out.
No Ice
Select this if you want to
turn off the icemaker
DA68-02912A-02.indb 2:17DA68-02912A-02.indb 2:17 14. 7. 18.  8:2114. 7. 18.  8:21
18_ operating
Do not put your fi ngers, hands or any
other unsuitable objects in the chute or
ice-maker bucket.
- It may result in personal injury or material
damage.
Never put fi nger or any other objects in
the dispenser opening.
- It may cause injury.
Use only the ice maker provided with the
refrigerator.
The water supply to this refrigerator must
only be installed/connected by a suitably
qualifi ed person and connect to a potable
water supply only.
In order to operate the ice maker properly,
water pressure of 138 ~ 862 kPa is
required.
If you have a long vacation or business
trip and won’t use water or ice
dispensers, close the water valve.
- Otherwise, water leakage may occur.
Wipe excess moisture from the inside and
leave the doors open.
- Otherwise, odor and mold may develop.
To get more space, you can remove the top
freezer drawer since it does not affect thermal
and mechanical characteristics. A declared
storage volume of frozen food storage
compartment is calculated with this drawer
removed.
USING THE COOLSELECT
ZONE™ DRAWER (OPTIONAL)
Quick Cool
You can use the Quick Cool feature with the
CoolSelect Zone
TM
.
“Quick Cool” allows 1~3 canned beverages to cool
within 60 min.
To cancel this function, press the “Quick Cool”
button again. CoolSelect Zone
TM
returns to the
previous temperature.
When “Quick Cool” ends, it returns to the “Cool”
temperature setting.
Thaw
Drips loss and quality deterioration of meats
reduces the freshness of foods.
After “Thaw” is selected, warm and cold air is
alternately supplied into the CoolSelect Zone
TM
Drawer.
Depending on the weight of meat, thawing time
can be selected for 4 hrs, 6 hrs, 10 hrs, and 12 hrs
sequentially.
When “Thaw” ends, CoolSelect Zone
TM
display
returns to “Zero Zone” condition.
When “Thaw “ ends, there are no juice in the meats
and they are half-freezed condition so it is easy to
cut them for cooking.
To cancel this option, press any button except
“Thaw”.
The approximate thawing time of meat and fi sh are
shown below. (Based on 1inch thickness)
THAW TIME WEIGHT
4 hours 363 g (0.8Ib)
6 hours 590 g (1.3Ib)
10 hours 771 g (1.7Ib)
12 hours 1000 g (2.2Ib)
Depending on the size and thickness of meat
and fi sh, the thawing time may vary.
The above weight represents the total weight of
food in the CoolSelect Zone
TM
Drawer.
Ex) The total thawing time for 400g frozen beef
and 600 g frozen chicken will be 10 hours.
With the “Thaw” option, food which is not
needed to thaw in the CoolSelect Zone
TM
Drawer should be removed.
WARNING
CAUTION
WARNING
DA68-02912A-02.indb 2:18DA68-02912A-02.indb 2:18 14. 7. 18.  8:2114. 7. 18.  8:21
operating _19
02 OPERATING
Zero Zone (0 ºC)
When “Zero Zone” is chosen, the temperature
of the CoolSelect Zone
TM
Drawer is kept at 0 ºC
regardless of the set refrigerator temperature.
“Zero Zone” temperature helps keep meat or fi sh
fresh longer.
Cool
When “Cool” is chosen, the temperature will be the
same as the set temperature of the refrigerator. The
digital panel shows the same temperature as that of
the display panel.
The CoolSelect Zone
TM
Drawer allows extra
refrigerator space.
Depending on the beverages, the cool-down
time may vary.
For “Quick Cool” option, food stored in
the CoolSelect Zone
TM
Drawer should be
removed.
REMOVING THE FREEZER
ACCESSORIES
Cleaning and rearranging the interior of the freezer is
simple.
1. Remove the Glass shelf by pulling the shelf out as
far as it will go. Then, gently lift it up and remove it.
2. Remove the door bin by holding the door bin with
both hands and then gently lift it up.
3. Remove the Plastic drawer by pulling it out and
slightly lifting it up.
4. Remove the Icemaker bucket by lifting up and
pulling it out.
Do not use excessive force when removing the
cover.
Otherwise, the cover may break and cause
injury.
WARNING
DA68-02912A-02.indb 2:19DA68-02912A-02.indb 2:19 14. 7. 18.  8:2114. 7. 18.  8:21
20_ operating
CAUTION
REMOVING THE FRIDGE
ACCESSORIES
1. Remove the spill Proof Glass Shelf by pulling the
shelf out as far as it will go. Then, gently lift it up
and gently remove it.
2. Remove the Vegetable & Fruit Drawer by
pressing on the indentations found on the inside
left and right sides of the Veggie Box/Dry Box
cover and remove by
pulling forward.
Holding the drawer
with one hand, lift it up
a little bit while pulling
it forward and take it
out of the refrigerator.
3. Remove the Gallon Door Bin by holding the bin
with both hands and gently lifting it up.
4. The Z Shelf is attached to the cabinet wall.
Remove the wine shelf by sliding it up and gently
lifting the shelf out of the tabs.
Ensure that the Z Shelf is fi tted as shown in
the diagram and not upside down.
Before removing any
accessories, make sure that
no food is in the way.
When possible, remove the food altogether to
reduce the risk of accidents.
CLEANING THE REFRIGERATOR
Do not use benzene, thinner, or Clorox,
Chloride for cleaning.
They may damage the surface of the
appliance and may cause a fi re.
Do not spray the refrigerator with water
while it is plugged in, as it may cause an
electric shock.
Do not clean the refrigerator with benzene,
thinner or car detergent for risk of fi re.
REPLACING THE INTERIOR
LIGHT
For LED lamp, please contact service engineer
to replace it.
WARNING
CAUTION
DA68-02912A-02.indb 2:20DA68-02912A-02.indb 2:20 14. 7. 18.  8:2114. 7. 18.  8:21
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Samsung RSH5ZLMR Manuel utilisateur

Catégorie
Frigos
Taper
Manuel utilisateur

dans d''autres langues