Samsung RS30GKASLA Manuel utilisateur

Marque: Samsung

Modèle: RS30GKASLA

Catégorie: Frigos

Taper: Manuel utilisateur

Ce manuel convient également à

RS30GKASL

English

Refrigerator

user manual

imagine the possibilities

Thank you for purchasing a Samsung product.

Free Standing Appliance

This manual is made with 100% recycled paper.

02_ safety information

SAFETY INFORMATION

• Before operating the appliance, please read this

manual thoroughly and retain it at a safe place

near the appliance for your future reference.

• Use this appliance only for its intended purpose

as described in this instruction manual. This

appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

• This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack

of experience and knowledge if they have been

given supervision or instruction concerning use of

the appliance in a safe way and understand the

hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be

made by children without supervision.

• Warnings and Important Safety Instructions in this

manual do not cover all possible conditions and

situations that may occur. It is your responsibility

to use common sense, caution, and care when

installing, maintaining, and operating your

appliance.

• Because these following operating instructions

cover various models, the characteristics of

your refrigerator may differ slightly from those

described in this manual and not all warning signs

may be applicable. If you have any questions or

concerns, contact your nearest service center

or find help and information online at www.

samsung.com.

Important safety symbols and

precautions:

WARNING

Hazards or unsafe practices that may

result in severe personal injury or

death.

CAUTION

Hazards or unsafe practices that may

result in minor personal injury or

property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions carefully.

Unplug the power plug from the wall

socket.

Make sure the machine is grounded to

prevent electric shock.

Call the contact center for help.

Note.

These warning signs are here to prevent injury to

you and others.

Please follow them carefully.

After reading this section, keep it in a safe place

for future reference.

CE Notice

This product has been determined to be in

compliance with the Low Voltage Directive

(2006/95/EC), the Electromagnetic Compatibility

Directive (2004/108/EC), RoHS Directive (2011/65/

EU), Commission Delegated Regulation (EU) No

1060/2010 and the Eco-Design Directive(2009/125/

EC) implemented by Regulation (EC) No 643/2009 of

the European Union. (For products sold in European

Countries only)

SEVERE WARNING SIGNS FOR

TRANSPORTATION AND SITE

• When transporting and installing the

appliance,care should be taken to ensure

that no parts of the refrigerating circuit are

damaged.

• R-600a or R-134a is used as a refrigerant. Check

the compressor label on the rear of the appliance

or the rating label inside the refrigerator to see

which refrigerant is used for your refrigerator.

• When this product contains flammable gas

(Refrigerant R-600a),

- Refrigerant leaking from the pipe work could

ignite or cause an eye injury. If a leak is detected,

avoid any naked flames or potential sources of

ignition and air the room in which the appliance is

standing for several minutes.

- In order to avoid the creation of a flammable

gas-air mixture if a leak in the refrigerating

WARNING

safety information

safety information _03

circuit occurs, the size of the room in which the

appliance may be sited depends on the amount

of refrigerant used.

- Never start up an appliance showing any signs

of damage. If in doubt, consult your dealer. The

room where the refrigerator will be sited must

be 1m³ in size for every 8g of R-600a refrigerant

inside the appliance. The amount of refrigerant

in your particular appliance is shown on the

identification plate inside the appliance.

- If the appliance contains isobutane refrigerant

(R-600a), a natural gas with high environmental

compatibility that is, however, also combustible.

When transporting and installing the appliance,

care should be taken to ensure that no parts of

the refrigerating circuit are damaged.

SEVERE WARNING SIGNS

FOR INSTALLATION

• Do not install this appliance in a humid, oily

or dusty location, in a location exposed to

direct sunlight and water (rain drops).

- Deteriorated insulation of electrical parts may

cause an electric shock or fire.

• Do not place this refrigerator in direct sunlight or

expose to the heat from stoves, room heaters or

other appliances.

• Do not plug several appliances into the same

multiple power board.

The refrigerator should always be plugged into

its own individual electrical outlet which has a

voltage rating that matched the rating plate.

- This provides the best performance and also

prevents overloading house wiring circuits, which

could cause a fire hazard from overheated wires.

If the wall socket is loose, do not insert the power

plug.

- There is a risk of electric shock or fire.

• Do not use a cord that shows cracks or abrasion

damage along its length or at either end.

• Do not bend the power cord excessively or place

heavy articles on it.

• Do not use aerosols near the refrigerator.

- Aerosols used near the refrigerator may cause an

explosion or fire.

• Do not install this appliance in a location where

gas may leak.

- This may result in an electric shock or fire.

• The installation or any service of this

appliance is recommended by a qualified

technician or service company.

- Failing to do so may result in an electric shock,

fire, explosion, problems with the product, or

WARNING

injury.

• This refrigerator must be properly installed and

located in accordance with the manual before it

is used.

• Connect the power plug in proper position with

the cord hanging down.

- If you connect the power plug upside down, wire

can get cut off and a cause fire or an electric

shock.

• Make sure that the power plug is not squashed

or damaged by the back of the refrigerator.

• When moving the refrigerator, be careful not to

roll over or damage the power cord.

- This constitutes a fire hazard.

• The appliance must be positioned so that the

plug is accessible after installation.

• The refrigerator must be grounded.

- You must ground the refrigerator to

prevent any power leakages or electric

shocks caused by current leakage from

the refrigerator.

• Never use gas pipes, telephone lines or other

potential lightening rods as ground.

- Improper use of the ground plug can result in an

electric shock.

• If the power cord is damaged, have it

replaced immediately by the manufacturer

or its service agent.

• The fuse on the refrigerator must be changed by

a qualified technician or service company.

- Failing to do so may result in an electric shock or

personal injury.

CAUTION SIGNS FOR

INSTALLATION

• Keep ventilation opening in the appliance

enclosure or mounting structure clear of

obstruction.

• Allow the appliance to stand for 2 hours after

installation.

SEVERE WARNING SIGNS

FOR USING

• Do not insert the power plug with wet

hands.

• Do not store articles on the top of the appliance.

- When you open or close the door, the articles

may fall and cause a personal injury and/or

material damage.

• Do not put items filled with water on the

CAUTION

WARNING

04_ safety information

refrigerator.

- If spilled, there is a risk of fire or electric shock.

• Do not let children hang on the door.

- Failure to do so may cause serious personal

injury.

• Do not leave the doors of the refrigerator open

while the refrigerator is unattended and do not let

children enter inside the refrigerator.

• Do not allow babies or children go inside the

drawer.

- It can cause death from suffocation by

entrapment or personal injury.

• Do not sit on the Freezer door.

- The door may be broken and cause a personal

injury.

• To prevent children entrapment, you must reinstall

the divider using provided screws after cleaning

or other actions if you removed the divider from

the drawer.

• Never put fingers or other objects into the

dispenser hole.

- Failure to do so may cause personal injury or

material damage.

• Do not store volatile or flammable substances

such as benzene, thinner, alcohol, ether or LP

gas in the refrigerator.

- The storage of any of such products may cause

an explosion.

• Do not store low temperature-sensitive

pharmaceutical products, scientific materials or

other low temperature-sensitive products in the

refrigerator.

- Products that require strict temperature controls

must not be stored in the refrigerator.

• Do not place or use electrical appliance inside

the refrigerator, unless they are of a type

recommended by the manufacturer.

• Do not use a hair dryer to dry the inside of the

refrigerator. Do not place a lighted candle in the

refrigerator for removing bad odors.

- This may result in an electric shock or fire.

• Do not touch the inside walls of the freezer or

products stored in the freezer with wet hands.

- This may cause frostbite.

• Do not use mechanical devices or any other

means to accelerate the defrosting process, other

than those recommended by the manufacturer.

• Do not damage the refrigerant circuit.

• This product is intended only for the

storage of food in a domestic environment.

• Bottles should be stored tightly together so that

they do not fall out.

• In the event of a gas leak (such as propane

gas, LP gas, etc.), ventilate immediately without

touching the power plug. Do not touch the

appliance or power cord.

- Do not use a ventilating fan.

- A spark may result in an explosion or fire.

• Use only the LED Lamps provided by

manufacturer or service agent.

• Children should be supervised to ensure that they

do not play with and/or climb into the appliance.

• Do not disassemble or repair the

refrigerator by yourself.

- You run a risk of causing a fire, malfunction and/

or personal injury. In case of malfunction, please

contact your service agent.

• If the appliance generates a strange noise,

a burning or smell or smoke, unplug the

power plug immediately and contact your

nearest service center.

- Failing to do so may result in an electric or fire

hazards.

• If you experience difficulty when changing the

light, contact service agent.

• If the products is equipped with the LED Lamp,

do not disassemble the Lamp Cover and LED

Lamp by yourself.

- Please contact your service agent.

• If any dust or water is in the refrigerator, pull

out power plug and contact your Samsung

Electronics service center.

- There is a risk of fire.

CAUTION SIGNS FOR USING

• To get best performance from the product,

- Do not place foods too closely in front of

the vents at the rear of the appliance as

it can obstruct free air circulation in the

refrigerator compartment.

- Wrap the food up properly or place it in airtight

containers before putting it into the refrigerator.

- Do not put any newly introduced food for freezing

near to already existing food.

• Do not place carbonated or fizzy drinks in the

freezer compartment. Do not put bottles or glass

containers in the freezer.

- When the contents freeze, the glass may break

and cause personal injury and property damage.

• Do not change or modify the functionality of the

refrigerator.

- Changes or modifications may result in a personal

injury and/or property damage. Any changes or

modifications performed by a 3rd party on this

completed appliance are neither covered under

Samsung warranty service, nor is Samsung

responsible for safety issues and damages that

result from 3rd party modifications.

• Do not block air holes.

CAUTION

safety information _05

- If the air holes are blocked, especially with a

plastic bag, the refrigerator can be over cooled. If

this cooling period lasts too long, the water filter

may break and cause water leakage.

- Do not put any newly introduced food for freezing

near to already existing food.

• Please observe maximum storage times and

expiry dates of frozen goods.

• Fill the water tank, ice tray, water cubes only with

potable water.

• Use only the ice-maker provided with the

refrigerator.

• The water supply to this refrigerator must only be

installed/connected by a suitably qualified person

and connected to a potable water supply only.

• In order to operate the ice-maker properly, water

pressure of 138~862kpa(1.4~8.8kgf/cm3) is

required.

• Do not spray volatile material such as insecticide

onto the surface of the appliance.

- As well as being harmful to humans, it may also

result in an electric shock, fire or problems with

the product.

• Do not apply strong shock or excessive force

onto the surface of glass.

- Broken glass may result in a personal injury and/

or property damage.

CAUTION SIGNS FOR CLEANING

AND MAINTENANCE

• Do not directly spray water inside or

outside the refrigerator.

- There is a risk of fire or electric shock.

• Do not use or place any substances sensitive

to temperature such as inflammable sprays,

inflammable objects, dry ice, medicine, or

chemicals near the refrigerator. Do not keep

volatile or inflammable objects or substances

(benzene, thinner, propane gas, etc.) in the

refrigerator.

- This refrigerator is for storing food only.

- This may result in a fire or an explosion.

• Do not spray cleaning products directly on the

display.

- Printed letters on the display may come off.

• Remove any foreign matter or dust from the

power plug pins. But do not use a wet or damp

cloth when cleaning the plug, remove any foreign

material or dust from the power plug pins.

- Otherwise there is a risk of fire or electric shock.

• Never put fingers or other objects into the

dispenser hole and ice chute.

- It may cause a personal injury or material

damage.

CAUTION

• Unplug the refrigerator before cleaning and

performing maintenance.

SEVERE WARNING SIGNS

FOR DISPOSAL

• Ensure that none of the pipes on the back

of the appliance are damaged prior to

disposal.

• R-600a or R-134a is used as a refrigerant. Check

the compressor label on the rear of the appliance

or the rating label inside the refrigerator to see

which refrigerant is used for your refrigerator.

When this product contains flammable gas

(Refrigerant R-600a), contact your local authority

in regard to safe disposal of this product.

Cyclopentane is used as an insulation blowing

gas. The gases in insulation material require

special disposal procedure. Please contact your

local authorities in regard to the environmentally

safe disposal of this product. Ensure that none

of the pipes on the back of the appliances are

damaged prior to disposal. The pipes shall be

broken in the open space.

• When disposing of this product or other

refrigerators, remove the door/door seals, door

latch so that small children or animals cannot

become trapped inside. Leave the shelves in

place so that children may not easily climb inside.

Children should be supervised to ensure that they

do not play with the old appliance.

• Please dispose of the packaging material for this

product in an environmentally friendly manner.

ADDITIONAL TIPS FOR PROPER USAGE

• In the event of a power failure, call the local office

of your Electricity Company and ask how long it

is going to last.

- Most power failures that are corrected within

an hour or two will not affect your refrigerator

temperatures. However, you should minimize the

number of door openin gs while the power is off.

- Should the power failure last more than 2 hours,

remove all ice in the Ice Bucket.

- Should the power failure last more than 24 hours,

remove all frozen food.

• If keys are provided with the refrigerator, the keys

should be kept out of the reach of children and

not be in the vicinity of the appliance.

• The appliance might not operate consistently

(possibility of temperature becoming too warm

in the refrigerator) when sited for an extended

period of time below the cold end of the range of

temperature for which the refrigerating appliance

WARNING

06_ safety information

is designed.

• Do not store food which spoils easily at low

temperature, such as bananas, melons.

• Your appliance is frost free, which means there is

no need to manually defrost your appliance, as

this will be carried out automatically.

• Temperature rise during defrosting can comply

with ISO requirements. But if you want to prevent

an undue rise in the temperature of the frozen

food while defrosting the appliance, please wrap

the frozen food up in several layers of newspaper.

• Any increase in temperature of frozen food during

defrosting can shorten its storage life.

Saving Energy Tips

- Install the appliance in a cool, dry room with

adequate ventilation.

Ensure that it is not exposed to direct sunlight

and never put it near a direct source of heat

(radiator, for example).

- Never block any vents or grilles on the appliance.

- Allow warm food to cool down before placing it in

the appliance.

- Put frozen food in the refrigerator to thaw. You

can then use the low temperatures of the frozen

products to cool food in the refrigerator.

- Do not keep the door of the appliance open for

too long when putting food in or taking food out.

The shorter time for which the door is open, the

less ice will form in the freezer.

- Clean the rear of the refrigerator regularly. Dust

increases energy consumption.

- Do not set temperature colder than necessary.

- Ensure sufficient air exhaust at the refrigerator

base and at the back wall of the refrigerator. Do

not cover air vent openings.

- Allow clearance to the right, left, back and top

when installing.

This will help reduce power consumption and

keep your energy bills lower.

- For the most efficient use of energy, please keep

the all inner fittings such as baskets, drawers,

shelves on the position supplied by manufacturer.

This appliance is intended to be used

in household and similar applications

such as

- staff kitchen areas in shops, offices and other

working environments;

- farm houses and by clients in hotels, motels and

other residential type environments;

- bed and breakfast type environments;

- catering and similar non-retail applications.

contents

SETTING UP YOUR SIDE-BY-SIDE REFRIGERATOR ……………………………………………………… 07

OPERATING THE SAMSUNG SIDE-BY-SIDE REFRIGERATOR …………………………………………… 13

TROUBLESHOOTING …………………………………………………………………………………………… 19

setting up _07

01 SETTING UP

GETTING READY TO INSTALL

THE REFRIGERATOR

Congratulations on the purchase of your Samsung

Side-By-Side Refrigerator. We hope you will enjoy

the many state-of-the-art features and efﬁ ciencies

that this new appliance has to offer.

Selecting the best location for the

refrigerator

•

Select a location with easy access to a water supply.

•

Select a location without direct exposure to sunlight.

• Select a location with level (or nearly level)

flooring.

• Select a location with enough space for the

refrigerator doors to open easily. See the diagram

below.

• Select a location that allows sufficient space to

the right,left, back, and top for air circulation. See

the diagram below.

•

Select a location that allows you to move the

refrigerator easily if it needs maintenance or service.

When moving your refrigerator

To prevent ﬂ oor damage, be sure the front levelling

legs are in the up position (above the ﬂ oor). Refer to

‘Levelling the refrigerator’ in this manual (page 9).

To protect the ﬁ nish of your ﬂ ooring while you are

installing the refrigerator, place a large section of the

cardboard carton under the refrigerator where you

are working.

When installing, servicing or cleaning behind

the refrigerator, be sure to pull the unit straight

out and push back straight in after ﬁ nishing.

setting up your side-by-side

refrigerator

50mm

at least 6mm

1727mm

1181mm

974mm

1016mm

1308mm

Leg

Screw Driver

CAUTION

08_ setting up

2. Remove two water lines (White one is for water

and the other one is for ice) by pressing the

coupler (1) and pulling the water line (2) away.

Reattaching the Water Supply Line

1. The Water Line must be fully Inserted to the

center of transparent coupler to prevent water

leakage from the dispenser.

2. Insert the 2 clips in the install pack and check

that it holds the line firmly.

Do not cut the water line. Gently separate it

from the coupler.

Removing the freezer door

A few things to mention ﬁ rst.

• Make sure that you lift the door straight up so the

hinges are not bent or broken.

• Be careful not to pinch the water tubing and wire

harness on the door.

• Place doors on a protected surface to prevent

scratching or damage.

SETTING UP THE

REFRIGERATOR

Now that you have your new Refrigerator installed in

place, you are ready to set up and enjoy the features

and functions of the appliance. By completing the

following steps, your Refrigerator should be fully

operational. If not, ﬁ rst check the power supply and

electricity source or try the troubleshooting section

at the back of this user’s guide. If you have any

further questions, contact your Samsung Electronics

service center.

1. Place the Refrigerator in an appropriate location

with reasonable clearance between the wall and

the Refrigerator. Refer to installation instructions

in this manual.

2. Once the Refrigerator is plugged in, make sure

the interior light comes on when you open the

doors.

3. Set the Temperature control to the coldest

temperature and wait for an hour. The Freezer

will get slightly chilled and the motor will run

smoothly.

4. After powering the Refrigerator, it will take a few

hours to reach the appropriate temperature. You

can store food and drinks in the Refrigerator after

the temperature is sufficiently cool.

SETTING UP THE

REFRIGERATOR DOORS

If your entrance won’t allow the refrigerator to pass

easily through it, you can remove the doors.

Separating the Water Supply Line

from the Refrigerator

1. Pull the two water lines (which are in the Fixer)

out to the front.

Make sure the color of the

water lines match.

Center of transparent

coupler

clip A (1/4”)

(6.35mm)

setting up _09

01 SETTING UP

Removing the Fridge Door

1. Remove a screw on the upper hinge cover

With the door open, disengage the two locking

tabs with a flat-head screw driver

and remove

it while the lifting up the rear of the cover

, and

then disconnect the wires by gently pulling them

apart

2. Removing the FIXER HINGE ,and next take off

the upper hinge. Be careful that the door does

not fall on you as you are removing it.

Be sure to keep track of all parts you are

removing.

3. Remove the door from the

lower hinge

by lifting

the door straight up

Reattaching the Fridge door

To reattach the fridge doors, replace parts in

reverse order.

LEVELLING THE

REFRIGERATOR

Now that the doors are back on the refrigerator, you

want to make sure the refrigerator is level so that

you can make ﬁ nal adjustments. If the refrigerator

is not level, it will not be possible to get the doors

perfectly even.

1. Remove a screw on the upper hinge cover

With the door open, disengage the two locking

tabs with a flat-head screw driver

and remove

it while the lifting up the rear of the cover

, and

then disconnect the wires by gently pulling them

apart

2. Removing the FIXER HINGE ,and next take off

the upper hinge. Be careful that the door does

not fall on you as you are removing it.

Be sure to keep track of all parts you are

removing.

3. Next, remove the door from the lower hinge

by carefully lifting the door straight up

Be careful not to pinch the water tubing and

wire harness on the door.

Reattaching the freezer doors

To reattach the freezer doors, replace parts in

reverse order

CAUTION

10_ setting up

When the door of the freezer is higher

than the fridge

Insert a ﬂ at-blade screwdriver into a slot on the

fridge leg, then turn it clockwise.

CHECKING THE WATER

DISPENSER LINE

A water dispenser is one of the helpful features on

your new Samsung Refrigerator. To help promote

better health, the Samsung water ﬁ lter removes

unwanted particles from your water. However, it

does not sterilize or destroy microorganisms. You

may need to purchase a water purifying system to

do that.

In order for the ice maker to operate properly, a

water pressure of 20~125 psi (pound per square

inch) is required. Under normal conditions, a 170 cc

(5.75 oz.) paper cup can be ﬁ lled in 10 seconds.

If the Refrigerator is installed in an area with low

water pressure (below 20psi), you can install a

booster pump to compensate for the low pressure.

Make sure the water storage tank inside the

Refrigerator is properly ﬁ lled. To do this, press the

water dispenser lever until the water runs from the

water outlet.

Water line installation kits are available at extra

cost from your dealer. We recommend using a

water supply kit that contains copper tubing.

The new hose-sets supplied with the

appliance are to be used and that old hose-

sets should not be reused.

Check the accessory list below.

Water line fixer and

screws

Pipe connector

Water line Clip

When the Freezer part is lower than

the Fridge part.

Insert a ﬂ at-blade screwdriver into a slot on the

Freezer Leg, then turn it clockwise.

When the Fridge part is lower than

the Freezer part.

Insert a ﬂ at-blade screwdriver into a slot on the

Fridge Leg, then turn it clockwise.

Refer to the next section for the best way to

make very minor adjustments to the doors.

MAKING MINOR ADJUSTMENTS

TO THE DOORS

Remember, a level refrigerator is necessary for

getting the doors perfectly even. If you need

help, review the previous section on levelling the

refrigerator.

When the door of the fridge is higher

than the freezer

Insert a ﬂ at-blade screwdriver into a slot on the

freezer leg, then turn it clockwise.

Screwdriver(-)

Freezer Leg

Screwdriver(-)

Fridge Leg

setting up _11

01 SETTING UP

If you have to repair or disassemble the water line,

cut off 6.5mm of the plastic tubing to make sure you

get a snug, leak-free connection.

Before being used, the leakage in these

places should be examined

• Samsung Warranty does not cover WATER LINE

INSTALLATION.

• It’ll be done at customer’s charge unless the retail

price includes installation cost.

• Please contact Plumber or Authorized Installer for

the installation if needed.

• If Water leakage occurs due to improper

installation, Please contact installer.

1. Slip the compression nut (A) through the supplied

plastic tubing (A).

2. Tighten the compression nut (A) onto the 1/4”

compression fitting.

- If you are using copper tubing, slip the

compression nut (B) (not included) and ferrule

(not included) on copper tubing (not included) as

shown.

- If you are using plastic tubing (B), insert the

molded end(Bulb) of the plastic tubing (B) into

the compression fitting.

Do not use without the molded end(Bulb) of

the plastic tubing (B).

3. Tighten the compression nut (B) onto the

compression fitting. Do not over-tighten the

compression nut (B).

4. Turn water on and check for any leakage.

Only connect the water line to a drinkable

water source.

If you have to repair or disassemble the water

line, cut off 1/4“ of the plastic tubing to make

sure you get a snug, leak-free connection.

Connecting to the water supply line

1. First, shut off the main water supply line.

2. Locate the nearest cold, drinking water line.

3. Follow the Water Line Installation Instructions in

the installation kit.

4. After connecting the water supply to the water

filter, turn your main water supply back on and

Dispense about 3L to clear and prime the water

filter.

Connecting the water line to the

refrigerator

1. Remove the cap from water line on the unit and

insert compression nut to the water line on the

unit after disassembling from provided water line.

2. Connect both water line from the unit and water

line in the kit

3. Tighten the compression nut onto the

compression fitting. Be careful no gap between

two items.

4. Turn water on and check for any leakage.

Only connect the water line to a drinkable

water source.

CAUTION

The water line must be connected to

the cold water pipe.

If it is connected to the hot water pipe,

it may cause the purifier to malfunction.

Close Main

Water pipe

Close Main

Water pipe

No gap

Remove

cap

Water Line

from unit

Water Line

from Kit

No gap

Loosen a

CAUTION

No Leak

CAUTION

12_ setting up

4. Additional flushing may be required in some

households.

5. Open the refrigerator door and make sure there

are no water leaks coming from the water filter.

A newly installed water ﬁ lter cartridge may

cause water to brieﬂ y spurt from the water

dispenser. This is due to air getting into the

line. It should pose no problem to operation.

Check the amount of water supplied

to the ic

e tray.

1. Lift up the icemaker cover and gently pull it out.

2. When you press the Test button for 3 seconds,

the ice cube container is filled with water from

the water supply tap. Check to make sure the

amount of water is correct (see the illustration

below). If the water level is too low, the ice cubes

will be small. This is a water pressure problem

from within the main water pipes, not the

refrigerator.

- It will take a few minutes for the water to

reach the correct level after you push the

Test button.

- Do not press the test button continuously when

the tray is filled with ice or water. Water may

overflow or ice jamming may occur.

- When the bucket is not installed, the ice maker

does not work.

- When Ice Off blinks on the display panel, reinsert

the bucket and/or make sure it’s installed

properly.

BEFORE USING ICEMAKER

Remove

- Hold the handle as shown in

Figure1.

- Slightly pull up the bottom part.

- Take out the ice bucket slowly.

Install

- Assemble the icemaker in the

reverse order of disassembly.

- Push the bucket in firmly until you

hear a clicking sound.

- If the bucket does not fit into its

place, turn the gear handle on its

back by 90 degrees and reinstall

it again as shown in Figure 2.

Before calling service

- Any sounds you hear when

the ice maker dumps ice into

the bucket are part of normal

operation.

- If you don’t dispense ice for a

long period of time, the ice may

form clumps in the ice bucket. If ice clumps form,

remove the remaining ice and empty the bucket.

- When ice does not come out, check for ice stuck

in the chute and remove it.

- When Ice Off blinks on the display panel,

reinsert the bucket and/or make sure it’s

installed properly.

- When the door is open, the Ice and water

dispenser do not work.

- If you close the door hard, it may cause water

spilling over the ice maker.

- To prevent dropping the ice bucket, use both

hands when removing it.

- To prevent injury, be sure to clean up any ice or

water that may have dropped on the floor.

- Do not let the children hang on the ice dispenser

or on the bucket. They may get hurt.

- Be sure not to put your hand or any object into

the ice chute. It may cause personal injury or

damage mechanical parts.

Removing residual matter inside the

water supply line after installing ﬁ lter.

1. Turn ON the main water supply.

2. Press the Water button and push the Dispenser

Lever.

3. Flush 1 gallons of water through the filter before

use. (Flush approximately 6 minutes.) This will

clean the water supply system and remove air

from the lines.

Figure 1

Figure 2

Figure 3

Ice Chute

Ice

Water

Ice maker

Test button

Check the

water level

CAUTION

operating _13

02 OPERATING

( 4 )

Lighting/

Hold 3

sec for

↔

Touching the Lighting button turns on the

Dispenser LED lamp (under the display)

in continuous mode so that it stays on

continuously. The button also lights up. If

you want the Dispenser lamp to come on

only when some one uses the dispenser,

press the Lighting button to turn the

continuous mode off.

Touch and hold this button for 3 seconds

to switch the temperature units between

°C and °F

( 5 )

Fridge

(Hold 3 sec

for Power

Cool)

Touch this button to set the Fridge

temperature.

You can set the temperature between 1°C

and 7°C.

Touch and hold the this button for 3

seconds to decrease the time needed to

cool products in the Refrigerator. This can

be helpful if you need to cool easily spoiled

items quickly or if the temperature in the

fridge has warmed dramatically

(For example, if the door was left open).

( 6 )

Ice Off

(Hold 3 sec

for child

lock)

If you don’t want to make more ice, touch

this button. Also, pressing and holding this

button for 3 second locks the display panel

and dispenser buttons so the buttons can

not be used. The Child Lock icon lights up

to indicate you’ve activated the Child Lock

function.

(7)

Ice Type

Touch this button to select your desired

ice type. Cubed and crushed ice modes

alternate each time you press the Ice Type

button.

Note that when you push the Ice Type

button, you turn the Water dispenser off.

USING THE CONTROL PANEL

( 1 )

Energy

Saver

Touching this button turns Energy Saver

mode on and off. When you turn Energy

Saver on, the Energy Saver icon lights up.

Turn Energy Saver off, and the icon goes

off. The Energy Saver function turns on

automatically when power is supplied to

the refrigerator.

If condensation or water drops appear on

the doors, turn the Energy Saver mode off.

( 2 )

Freezer

(Hold 3 sec

for Power

Freeze)

Touch this button to set the Freezer

temperature.

You can set the temperature between

-14°C and -23°C.

Touch and hold this button for 3 seconds

to decrease the time needed to freeze

products in the Freezer. It can be helpful

if you need to freeze easily spoiled items

quickly or if the temperature in the Freezer

has warmed dramatically (For example, if

the door was left open).

( 3 )

Alarm /

Hold 3

sec for

Filter

Reset

This button serves two purposes:

1) To turn the door open alarm on

and off.

If the door alarm is set to On, an alarm

beeps if any refrigerator door is left open

for more than three minutes. The beeping

stops when you close the door. The door

alarm function is pre-set to On in the

factory. You can turn it off by touching and

then releasing this button. You can turn

it back on in the same fashion. The icon

lights up when the function is on.

2) After you replace the water filter,

Touch and hold this button for 3

seconds to reset the water filter

life indicator.

operating the SAMSUNG side-

by-side refrigerator

14_ operating

Controlling the Freezer temperature

You can set the Freezer temperature between -23°C

and -14°C to suit your particular needs. Touch

the Freezer button repeatedly until the desired

temperature is shown in the temperature display.

The temperature will move 1°C degrees with each

Touch as follows: -20°C → -21°C → -22°C → -23°C

→ -14°C → -15°C → -16°C → -17°C → -18°C →

-19°C → -20°C. Keep in mind that foods such as ice

cream can melt at -15°C. The temperature display

will move sequentially from -23°C to -14°C.

Controlling the fridge temperature

You can set the fridge temperature between 7°C and

1°C to suit your particular needs. Touch the Fridge

button repeatedly until the desired temperature is

shown in the temperature display. The temperature

will move 1°C degrees with each touch as follows:

3°C → 2°C → 1°C → 7°C → 6°C → 5°C → 4°C →

3°C. The temperature control process for the Fridge

works just like the Freezer process. Touch the Fridge

button to set your desired temperature. After a few

seconds, the Fridge will begin adjusting towards the

newly set temperature. This will be reﬂ ected in the

digital display.

(8)

Water

Touch this button to dispense water. Note

that you cannot dispense water and ice

simultaneously.

The Water dispenser turns off when you

press the Ice Type button.

( 9 )

Ice Off

When you touch the Ice Off button (

), the Ice Off icon lights and the Ice Maker

stops making ice.

We recommend you stop ice

making if the following occur:

- There is enough ice in the ice bucket.

- You want to save water and energy.

- Water is not being supplied to the

refrigerator.

If the ice maker function is

ON, and the water line is not

connected, there will be a water

valve noise from back of the unit.

Press the Ice Off (Hold 3sec for

child lock) button (

) for less

than 3 seconds until the Ice Off

Indicator (

) illuminates.

If you do not touch any button, the freezer and fridge

temperature indicator turn off in a few seconds.

If you touch any button, the display lights up again.

( 10 )

Filter

Water ﬁ lter usage

The Water Filter icon lights in red when you

need to change the water ﬁ lter.

This occurs after you use about 300

gallons of water (which usually takes

about 6 months). The icon will blink red for

several seconds when you open or close

the door.

CONTROLLING THE

TEMPERATURE

Basic temperature of Freezer and

Refrigerator Compartments

The basic temperature and recommended

temperatures of the Freezer and Refrigerator

Compartments are -20°C and 3°C respectively.

If the temperature of the Freezer or Refrigerator

Compartments are too high or low, adjust the

temperature manually.

Recommend Temp (Freezer) : -20°C

Recommend Temp (Fridge) : 3

°C

operating _15

02 OPERATING

• In case ice doesn’t come out, pull out the ice

bucket and press the test button located on the

right side of ice maker.

• Do not press the test button continuously when

the tray is filled with ice or water. Water may

overflow or ice may jam the bucket.

• When you press the Test button, you will

hear the refrigerator chime (ding-dong).

When the chime sounds, release the Test

button.

• The chime sounds automatically again to let you

know the ice maker is working well.

If a power failure occurs, ice cubes may melt

then freeze together when the power comes

back on, causing the dispenser to be out of

order.

To prevent this problem, after a power failure, pull

out the ice bucket and discard the residual ice or

water.

After you dump the ice from the ice bucket,

you should press the dispenser lever once

with the ‘ICE CUBED’ or ‘CRUSHED’ function

ON.

The ice maker will make new ice faster after you

return the ice bucket to the refrigerator.

• Do not put your fingers, hands or any

other unsuitable objects in the chute or

ice-maker bucket. It may result in personal

injury or material damage.

• Use only the ice maker provided with the

refrigerator.

• The water supply to this refrigerator must be

installed/connected by a suitably qualified person

and connect to a potable water supply only.

•

For the the ice maker to operate properly, the water

pressure must be between 20 and 125 psi.

- The temperature of the Freezer or Fridge

may rise when you open the doors too

frequently, or if a large amount of warm or

hot food is placed inside.

- This may cause the digital display to blink. Once

the Freezer and Fridge temperatures return to

their normal set temperatures, the blinking will

stop.

- If the blinking continues, you may need to “reset”

the Refrigerator. Try unplugging the appliance,

wait for around 10 minutes, and then plug the

power cord back in.

- If there is a communication error between the

Display and Main Controller, the Convertible

Display light may blink. If the blinking continues

for a long period of time, please contact a

Samsung Electronics Service Center.

HOW TO USE THE DISPENSER

Push the appropriate Ice Type button

or the Water button to select what

you want dispensed.

Press the Ice Type button to select

the type of ice you want. Place your

cup under the ice outlet and push

gently against the dispenser lever.

Make sure the glass is in line with

the dispenser to prevent the ice

from bouncing out. When you select

Cubed Ice after using the Crushed

Ice feature, a small amount of

residual crushed ice might be produced.

Please wait 2 seconds before removing the

glass under the dispenser to prevent spills.

If the Refrigerator door opens, the Dispenser does

not work.

• Do not pull the lever out. You could damage or

break the lever’s spring.

• To clean the ice bin/bucket, wash with a mild

detergent, rinse well, and dry thoroughly it. Do

not use harsh or abrasive cleaners or solvents.

NO ICE

Select this if you want to turn

ice maker off

CAUTION

WARNING

16_ operating

When “Thaw” ends, food is in a half-frozen state,

making it easy to cut for cooking. In addition, when

“Thaw” ends, the CoolSelect Zone™ Drawer returns

to the original “Chill” condition. To cancel this

function mid-cycle, just press any button besides

Thaw.

Here are the approximate thawing times of meat

and ﬁ sh by weight (and based on a 25.4mm (1in.)

thickness). This chart represents the total weight of

food in the CoolSelect Zone™ Drawer.

THAW TIME WEIGHT

4hours 363g (0.8Ib)

6hours 590g (1.3Ib)

10hours 771g (1.7Ib)

12hours 1000g (2.2Ib)

Quick Cool

You can use the “Quick Cool” operation with the

CoolSelect Zone™ Drawer to quickly cool 1~3

canned beverages in about an hour. When the

“Quick Cool” process ends, the CoolSelect Zone™

Drawer automatically returns to the previously set

temperature.

To cancel this operation, press the Quick Cool

button again and the CoolSelect Zone™ Drawer

returns to the previously set temperature.

Fresh

When “Cool” is selected, the temperature in the

CoolSelect Zone™ Drawer will be the same as the

overall temperature setting of the refrigerator. The

drawer digital panel shows the same temperature

as that of the refrigerator display panel. Since the

“Cool” function mimics the refrigerator temperature,

you have extra general storage space.

Depending on the size and thickness of the

meat or ﬁ sh, thawing times may vary.

When “Thaw” is in operation, any items that

you do not want affected should be moved

out of the drawer.

• If you have a

long vacation

or business trip

and won’t use

the water or ice

dispensers, close

the water valve.

- Otherwise, water

leakage may occur.

• When you have not

used the Ice maker for

a while, or you have

opened the Freezer door frequently, the Ice may

stick together. If this has occurred, empty the ice

bucket or break up the ice with a wood kitchen

tool. Do not use sharp items such as knives or

forks.

• When the bucket is removed, there may still

be some residual ice in the ice maker that the

icemaker can release.

• If ice does not

dispense, pull

out the icemaker

cover and press

test button

located on the ice

maker.

• Do not press the test

button continuously

when the tray is filled with ice or water. Water

may overflow or the ice may jam the icemaker or

dispenser.

USING THE COOLSELECT

ZONE™ DRAWER

The CoolSelect Zone™ Drawer is designed to make

your busy life just a little bit easier.

Chill

When “Chill” is selected, the temperature of

the CoolSelect Zone™ Drawer is kept at -1°C,

regardless of the overall temperature setting of the

refrigerator. This feature also helps keep meat or ﬁ sh

fresh for longer.

Thaw

When “Thaw” is selected, warm and cold air is

alternately blown into the CoolSelect Zone™ Drawer.

Depending on the weight of the frozen food, you

can select a 4 hrs, 6 hrs, 10 hrs, and 12 hrs thawing

time.

Ice Chute

Ice Bucket

Ice-Maker Cover

CAUTION

Test button

CAUTION

operating _17

02 OPERATING

5. Ice Bucket (Freezer)

Remove the Icemaker Bucket

by lifting up and pulling it out

slowly.

• Grip the handle as shown

in the figure.

• Lift the low part slightly.

• Take the ice bucket out

slowly.

Do not use excessive force when removing

the drawer cover.

You can break the cover and cause injury.

Before removing any accessories, make sure

that no food is in the way.

When possible, remove the food altogether to

reduce the risk of accidents.

CHANGING THE INTERIOR

LIGHTS

Do not disassemble or replace the LED type

Lighting.

To change the LED Type Lighting, contact a

Samsung service center.

TO IMPROVE THE COOLING

PERFORMANCE

If the cold air

outlet is blocked

by food items, the

cold air cannot

penetrate the entire

compartment and

will be unable

to freeze the

food efﬁ ciently

which results in

a degraded cooling

performance.

In particular, there is load

limit at the top of the

freezing compartment.

Please do not put food

items above this limit.

CLEANING THE REFRIGERATOR

Do not use Benzene, Thinner or Clorox™, or

car detergent to clean the Refrigerator.

They may damage the surface of the

appliance and can create a risk of ﬁ re.

Do not spray the refrigerator with water while

it is plugged in, as it may cause an electric

shock.

REMOVING THE FREEZER/

FRIDGE ACCESSORIES

Cleaning and rearranging the interior of the freezer

is a snap.

1. Shelves (Freezer/Fridge)

Pull the shelf out as far

as it goes and then lift up

and remove it.

2. DOOR BIN

Remove the Door Bin

by holding it with both

hands, and then gently

lift it up.

3. DRAWER

Remove the Drawer by

pulling it out and lifting it

up slightly.

4. Drawer Cover

Pull the cover out as far

as it goes, and then lift up

and remove it.

CAUTION

WARNING

CAUTION

Cold air outlet

Load limit in

the freezing

compartment

18_ operating

water filter. The color of indicator changes from

red to light off.

A newly installed water ﬁ lter cartridge may

cause water to brieﬂ y spurt from the water

dispenser. This is due to air getting into the

line. It should pose no problem to operation.

Removing residual matter inside the

water supply line after installing a

new ﬁ lter

1. Press the Water button, and then push the

Dispenser Lever with a cup or glass.

2. Flush 1 gallon of water through the filter, one

cup or glass at a time. (Flush approximately 6

minutes.) This will clean the water supply system

and remove air from the lines.

- Additional flushing may be required in some

households.

3. Open the refrigerator door and make sure there

are no water leaks coming from the water filter.

Reverse Osmosis Water Supply

IMPORTANT : The pressure of the water supply

coming out of a reverse osmosis system going to

the water inlet valve of the refrigerator needs to be

between 35 and 120 psi (241 and 827 kPa).

If a reverse osmosis water ﬁ ltration system is

connected to your cold water supply, the water

pressure to the reverse osmosis system needs to be

a minimum of 40 to 60 psi (276 to 414 kPa.)

If the water pressure to the reverse osmosis system

is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the

reverse osmosis system is blocked. Replace the

filter if necessary.

• Allow the storage tank on the reverse osmosis

system to refill after heavy usage.

• If your refrigerator has a water filter, it may

further reduce the water pressure when used

in conjunction with a reverse osmosis system.

Remove the water filter.

If you have questions about your water pressure, call

a licensed, qualiﬁ ed plumber.

Ordering replacement ﬁ lters

To order more water ﬁ lter cartridges, contact your

authorized Samsung dealer.

CHANGING THE WATER FILTER

To reduce risk of water damage to your

property DO NOT use generic brands of

water ﬁ lers in your SAMSUNG Refrigerator.

USE ONLY SAMSUNG BRAND WATER

FILTERS.

SAMSUNG is not legally responsible for any

damage, including, but not limited to property

damage caused by water leakage from the use of a

generic water ﬁ lter.

SAMSUNG Refrigerators are designed to work

ONLY WITH SAMSUNG Water Filters.

The “Filter Indicator” light lets you know when it is

time to change your water ﬁ lter cartridge. To give

you preparation time to get a new ﬁ lter, the red light

will come on just before the capacity of the current

ﬁ lter runs out. Changing the ﬁ lter on time provides

you with the freshest, cleanest water from your

fridge.

To change the water ﬁ lter, follow these steps:

1. Turn the water filter 90˚

counter-clockwise.

2. Pull the water filter from

the filter housing.

3. Insert new water filter

inside the filter housing.

4. Turn the new water filter

90˚ clockwise.

5. Press the “Alarm/hold 3 sec for Filter Reset”

button (

) for about 3 seconds to reset the

WARNING

troubleshooting _19

03 TROUBLESHOOTING

troubleshooting

PROBLEM SOLUTION

The refrigerator does

not work at all or it does

not chill sufficiently.

• Check that the power plug is properly connected.

• Is the temperature control on the display panel set to the correct temperature?

Try setting it to a lower temperature.

• Is the refrigerator in direct sunlight or located too near a heat source?

• Is the back of the refrigerator too close to the wall and therefore keeping air from

circulating?

The food in the fridge is

frozen.

• Is the temperature control on the display panel set to the correct temperature?

Try setting it to a warmer temperature.

• Is the temperature in the room very low?

• Did you store the food with a high water content in the coldest part of the fridge?

You hear unusual noises

or sounds.

• Check that the refrigerator is level and stable.

• Is the back of the refrigerator too close to the wall and therefore keeping air from

circulating?

• Was anything dropped behind or under the refrigerator?

• A “ticking” sound is heard from inside the refrigerator. This is normal and occurs

because various accessories are contracting or expanding in relation to the

temperature of the refrigerator interior.

The front corners of

the appliance are hot

and condensation is

occurring.

• Some heat is normal as anti-condensators are installed in the front corners of the

refrigerator to prevent condensation.

• Is the refrigerator door ajar? Condensation can occur when you leave the door

open for a long time.

Ice is not dispensing.

• Did you wait at least 12 hours after installation of the water supply line before

making ice?

• Is the water line connected and the shut-off valve open?

• Did you manually stop the ice making function? Make sure Ice Type is set to

Cubed or Crushed.

• Is there any ice blocked within the ice maker bucket?

• Is the freezer temperature too warm? Try setting the freezer temperature lower.

You can hear water

bubbling in the

refrigerator.

• This is normal. The bubbling comes from the refrigerant coolant liquid circulating

through the refrigerator.

There is a bad smell in

the refrigerator.

• Has a food item spoiled?

• Make sure that strong smelling food (for example, fish) is wrapped so that it is

airtight.

• Clean out your freezer periodically and throw away any spoiled or suspect food.

Frost forms on the walls

of the freezer.

• Is the air vent blocked? Remove any obstructions so air can circulate freely.

• Allow sufficient space between the foods stored for efficient air circulation.

• Is the freezer door closed properly?

Water dispenser is not

functioning.

• Is the water line connected and the shut-off valve open?

• Has the water supply line tubing been crushed or kinked? Make sure the tubing

is free and clear of any obstruction.

• Is the water tank frozen because the refrigerator temperature is too low? Try

selecting a warmer setting on the main display panel.

Ambient Room Temperature Limits

This refrigerator is designed to operate in ambient temperatures speciﬁ ed by its

temperature class marked on the rating plate.

Class Symbol

Ambient Temperature range (°C)

IEC 62552 (ISO 15502) ISO 8561

Extended Temperate SN +10 to +32 +10 to +32

Temperate N +16 to +32 +16 to +32

Subtropical ST +16 to +38 +18 to +38

Tropical T +16 to +43 +18 to +43

Internal temperatures may be affected by such factors as the location of the fridge/freezer, ambient

temperature and the frequency with which you open the door. Adjust the temperature as required to

compensate for these factors.

English

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic

accessories (e.g. charger, headset, USB cable) should not be disposed of with other household

waste at the end of their working life. To prevent possible harm to the environment or human

health from uncontrolled waste disposal, please separate these items from other types of waste

and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their lo-

cal government ofﬁ ce, for details of where and how they can take these items for environmentally

safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase

contract. This product and its electronic accessories should not be mixed with other commercial

wastes for disposal.

Contact SAMSUNG WORLD WIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG

customer care center.

COUNTRY CALL WEBSITE

MENA

U.A.E 800-SAMSUNG (800 - 726 7864)

www.samsung.com/ae/support (English)

www.samsung.com/ae_ar/support (Arabic)

OMAN 800-SAMSUNG (800 - 726 7864)

KUWAIT 183-CALL (183-2255)

BAHRAIN 8000-GSAM (8000-4726)

QATAR 800-CALL (800-2255)

EGYPT

08000-726786

16580

www.samsung.com/eg/support

ALGERIA 021 36 11 00 www.samsung.com/n_africa/support

PAKISTAN 0800-Samsung (72678) www.samsung.com/pk/support

TUNISIA 80-1000-12 www.samsung.com/n_africa/support

JORDAN

0800-22273

06 5777444

www.samsung.com/Levant/support (English)

SYRIA 18252273 www.samsung.com/Levant/support (English)

MOROCCO 080 100 2255 www.samsung.com/n_africa/support

SAUDI ARABIA 920021230

www.samsung.com/sa/support

www.samsung.com/sa_en/support (English)

La page charge ...

Samsung RS30GKASLA Manuel utilisateur

Marque: Samsung

Modèle: RS30GKASLA

Catégorie: Frigos

Taper: Manuel utilisateur

Ce manuel convient également à

RS30GKASL

Télécharger le PDF

rapport

dans d''autres langues

English: Samsung RS30GKASLA User manual

Documents connexes

Autres documents

TCL RF282BSF0UK Manuel utilisateur