Ingersoll-Rand 3000P Operation and Maintenance Manual

Marque: Ingersoll-Rand

Modèle: 3000P

Catégorie: Outils électroportatifs

Taper: Operation and Maintenance Manual

Ce manuel convient également à

2400P

Refer All Communications to the Nearest

Ingersoll–Rand Office or Distributor.

 Ingersoll–Rand Company 2000

Printed in Japan

03539509

Form P7078

Edition 5

June, 2000

OPERATION AND MAINTENANCE MANUAL FOR

MODELS 2400P AND 3000P

TWIN BLADE IMPULSE WRENCHES

Models 2400P and 3000P Impulse Wrenches are designed for assembly operations

which require high speed rundown of fasteners with consistent torque delivery and

reduced torque reaction.

Ingersoll–Rand is not responsible for customer modification of tools for applications on

which Ingersoll–Rand was not consulted.

IMPORTANT SAFETY INFORMATION ENCLOSED.

READ THIS MANUAL BEFORE OPERATING TOOL.

IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION

IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.

FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.

PLACING TOOL IN SERVICE

• Always operate, inspect and maintain this tool in

accordance with American National Standards

Institute Safety Code for Portable Air Tools

(ANSI B186.1).

• For safety, top performance, and maximum

durability of parts, operate this tool at 90 psig

(6.2 bar/620 kPa) maximum air pressure at the inlet

with 1/2” (13 mm) inside diameter air supply hose.

• Always turn off the air supply and disconnect the

air supply hose before installing, removing or

adjusting any accessory on this tool, or before

performing any maintenance on this tool.

• Do not use damaged, frayed or deteriorated air

hoses and fittings.

• Be sure all hoses and fittings are the correct size

and are tightly secured. See Dwg. TPD905–1 for a

typical piping arrangement.

• Always use clean, dry air at 90 psig

(6.2 bar/620 kPa) maximum air pressure. Dust,

corrosive fumes and/or excessive moisture can ruin

the motor of an air tool.

• Do not lubricate tools with flammable or volatile

liquids such as kerosene, diesel or jet fuel.

• Do not remove any labels. Replace any damaged

label.

USING THE TOOL

• Always wear eye protection when operating or

performing maintenance on this tool.

• Always wear hearing protection when operating

this tool.

• Keep hands, loose clothing and long hair away from

rotating end of tool.

• Anticipate and be alert for sudden changes in

motion during start up and operation of any power

tool.

• Keep body stance balanced and firm. Do not

overreach when operating this tool. High reaction

torques can occur at or below the recommended air

pressure.

• Tool shaft may continue to rotate briefly after

throttle is released.

• Air powered tools can vibrate in use. Vibration,

repetitive motions or uncomfortable positions may

be harmful to your hands and arms. Stop using any

tool if discomfort, tingling feeling or pain occurs.

Seek medical advice before resuming use.

• Use accessories recommended by Ingersoll–Rand.

• Use only impact sockets and accessories. Do not use

hand (chrome) sockets or accessories.

• This tool is not designed for working in explosive

atmospheres.

• This tool is not insulated against electric shock.

The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool

performance, and increased maintenance, and may invalidate all warranties.

Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized

Servicenter.

WARNING LABEL IDENTIFICATION

FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.

Always wear eye protection

when operating or perform-

ing maintenance on this

tool.

WARNING

Always wear hearing

protection when operating

this tool.

Always turn off the air sup-

ply and disconnect the air

supply hose before install-

ing, removing or adjusting

any accessory on this tool,

or before performing any

maintenance on this tool.

WARNING

Air powered tools can vibrate

in use. Vibration, repetitive

motions or uncomfortable po-

sitions may be harmful to your

hands and arms. Stop using

any tool if discomfort, tingling

feeling or pain occurs. Seek

medical advice before resum-

ing use.

WARNING

Do not carry the tool by

the hose.

WARNING

Do not use damaged, frayed

or deteriorated air hoses

and fittings.

WARNING

Keep body stance balanced

and firm. Do not overreach

when operating this tool.

WARNING

Operate at 90 psig (6.2 bar/

620 kPa) Maximum air pressure.

90 psig

(6.2bar/620kPa)

ADJUSTMENTS

TORQUE ADJUSTMENT

To adjust the torque on these Twin Blade Impulse

Wrenches, proceed as follows:

1. Remove the Adjustment Hole Plug.

2. Rotate the Drive Shaft until the Torque Adjustment

Screw is visible in the opening.

3. Using a 1.5 mm hex wrench, rotate the Adjustment

Screw clockwise to increase the torque output and

counterclockwise to decrease the torque output. Do

not rotate the Oil Plug.

Make all final adjustments at the job.

4. Replace the Adjustment Hole Plug.

CHANGING THE MECHANISM FLUID

To change the Mechanism Fluid in the Impulse Mechanism,

proceed as follows:

1. Remove the Rubber Housing Boot.

2. Using a hex wrench, remove the four Hammer Case

Cap Screws and Lock Washers. Lift the Hammer Case

off the Motor Housing over the Drive Shaft. Remove

the Hammer Case Gasket.

3. Lift the assembled mechanism off the Rotor.

4. Using a 2 mm hex wrench, rotate the Torque

Adjustment Screw clockwise until the Screw stops.

Rotate the Screw counterclockwise until it stops or

makes six complete revolutions.

5. Using a 2.5 mm hex wrench, unscrew and remove the

Oil Plug. Remove the Oil Plug Seal and Oil Plug Seal

Support.

6. With the oil plug opening downward over a container,

rotate the Drive Shaft to purge the fluid from the

mechanism.

7. Thread the Tee Wrench included with the Tool Kit

(Part No. 1900P–99) into the Piston Stop Assembly

that is 180 degrees from the Torque Adjustment Screw

and pull the Stop Assembly toward the output end of

the mechanism until it stops.

8. Using the syringe and fluid from the Fluid

Replacement Kit (Part No. EQ106S–K400), fill the

mechanism with the fluid furnished in the Kit until the

fluid overflows the fill hole. Model 2400P will require

30 cc of fluid, Model 3000P, 43 cc.

See Dwg. TPD1265.

DO NOT SUBSTITUTE ANY OTHER FLUID.

Failure to use the impulse mechanism fluid

provided could damage the tool, increase

maintenance and decrease performance. Use only

clean fluid in these tools.

ADJUSTMENTS

(Dwg. TPD1265)

9. Submerge the fill opening in the remainder of the fluid,

and using a wrench, rotate the Drive Shaft to purge any

remaining air from the system.

10. Remove the mechanism from from the fluid and use

the Tee Wrench to push the Piston Stop Assembly

slowly downward until fluid flows from the fill

opening.

11. Thread the Oil Plug with the Oil Plug Seal and Seal

Support into the mechanism until it is snug.

12. Using a 2 mm hex wrench, turn the Torque Adjustment

Screw clockwise until it stops. This is the maximum

torque position.

13. Wipe the outside of the mechanism dry and clean and

remove the Oil Chamber Plug. Using the syringe,

withdraw 0.5 cc of fluid from 2400P models and 1.0 cc

from 3000P models.

14. Install the Oil Chamber Plug and tighten it between 20

and 25 in–lb (2.3 and 2.8 Nm) torque.

15. Position a new Hammer Case Gasket on the Motor

Housing and install the assembled mechanism on the

rotor shaft.

16. Place the Hammer Case Cover over the Drive Shaft

against the Housing and Gasket. Install the four

Hammer Case Cap Screws and Lock Washers. Tighten

each Screw between 45 and 50 in–lb (5.1 and 5.6 Nm)

torque.

17. Install the Rubber Housing Boot on the tool.

PLACING TOOL IN SERVICE

LUBRICATION

Ingersoll–Rand No. 50 Ingersoll–Rand No. 67

Ingersoll–Rand Fluid Part

No. EQ106S–400–1

Always use an air line lubricator with these tools.

We recommend the following Filter–Lubricator–Regulator

Unit:

USA – No. C18–03–FKG0–28

After each 20 000 cycles, or as experience indicates, drain

and refill the Impulse Unit Drive Assembly as instructed in

this manual using the Fluid Replacement Kit (Part

No. EQ106S–K400). Lubricate the hex drive and the output

shaft before assembly.

MAIN LINES 3 TIMES

AIR TOOL INLET SIZE

AIR

SYSTEM

AIR

TOOL

LUBRICATOR

REGULATOR

FILTER

BRANCH LINE 2 TIMES

AIR TOOL INLET SIZE

DRAIN REGULARLY

COMPRESSOR

(Dwg. TPD905–1)

HOW TO ORDER AN IMPULSE WRENCH

Model Free Speed Recommended Torque Range

Soft Draw Hard Slam

ft–lb Nm ft–lb Nm

PISTOL GRIP with 1/2” SQUARE DRIVE

2400P 4,300 35–80 47–108 107–170 145–230

PISTOL GRIP with 3/4” SQUARE DRIVE

3000P 4,500 60–110 82–150 124–210 169–286

Adressez toutes vos communications au Bureau

Ingersoll–Rand ou distributeur le plus proche.

 Ingersoll–Rand Company 2000

Imprimé au Japon

MANUEL D’EXPLOITATION ET D’ENTRETIEN

DES CLÉS HYDRO–PNEUMATIQUES À DOUBLE

PALETTE MODÈLES 2400P ET 3000P

NOTE

Les clés hydro–pneumatiques à double palette Modèles 2400P et 3000P sont destinées aux opérations

d’assemblage nécessitant une grande vitesse de serrage avec une régularité du couple et un serrage

virtuellement sans réaction sur l’opérateur.

Ingersoll–Rand ne peut être tenu responsable de la modification des outils par le client pour les adapter à

des applications qui n’ont pas été approuvées par Ingersoll–Rand.

ATTENTION

D’IMPORTANTES INFORMATIONS DE SÉCURITÉ SONT JOINTES.

LIRE CE MANUEL AVANT D’UTILISER L’OUTIL.

L’EMPLOYEUR EST TENU DE COMMUNIQUER LES INFORMATIONS

DE CE MANUEL AUX EMPLOYÉS UTILISANT CET OUTIL.

LE NON RESPECT DES AVERTISSEMENTS SUIVANTS PEUT CAUSER DES BLESSURES.

MISE EN SERVICE DE L’OUTIL

S Toujours exploiter, inspecter et entretenir cet outil

conformément au Code de sécurité des outils

pneumatiques portatifs de l’American National

Standards Institute (ANSI B186.1).

• Pour la sécurité, les performances optimales et la

durabilité maximale des pièces, cet outil doit être

connecté à une alimentation d’air comprimé de

6,2 bar (620 kPa) maximum à l’entrée, avec un

flexible de 13 mm de diamètre intérieur.

• Couper toujours l’alimentation d’air comprimé et

débrancher le flexible d’alimentation avant d’installer,

déposer ou ajuster tout accessoire sur cet outil, ou

d’entreprendre une opération d’entretien quelconque

sur l’outil.

• Ne pas utiliser des flexibles ou des raccords

endommagés, effilochés ou détériorés.

• S’assurer que tous les flexibles et les raccords sont

correctement dimensionnés et bien serrés. Voir Plan

TPD905–1 pour un exemple type d’agencement des

tuyauteries.

• Utiliser toujours de l’air sec et propre à une pression

maximum de 6,2 bar (620 kPa). La poussière, les

fumées corrosives et/ou une humidité excessive

peuvent endommager le moteur d’un outil

pneumatique.

• Ne jamais lubrifier les outils avec des liquides

inflammables ou volatiles tels que le kérosène, le

gasoil ou le carburant d’aviation.

• Ne retirer aucune étiquette. Remplacer toute étiquette

endommagée.

UTILISATION DE L’OUTIL

• Porter toujours des lunettes de protection pendant

l’utilisation et l’entretien de cet outil.

• Porter toujours une protection acoustique pendant

l’utilisation de cet outil.

• Tenir les mains, les vêtements flous et les cheveux

longs, éloignés de l’extrémité rotative de l’outil.

• Prévoir, et ne pas oublier, que tout outil motorisé est

susceptible d’à–coups brusques lors de sa mise en

marche et pendant son utilisation.

• Garder une position équilibrée et ferme. Ne pas se

pencher trop en avant pendant l’utilisation de cet

outil. Des couples de réaction élevés peuvent se

produire à, ou en dessous, de la pression d’air

recommandée.

• La rotation des accessoires de l’outil peut continuer

pendant un certain temps après le relâchement de la

gâchette.

• Les outils pneumatiques peuvent vibrer pendant

l’exploitation. Les vibrations, les mouvements

répétitifs et les positions inconfortables peuvent

causer des douleurs dans les mains et les bras.

N’utiliser plus d’outils en cas d’inconfort, de

picotements ou de douleurs. Consulter un médecin

avant de recommencer à utiliser l’outil.

• Utiliser les accessoires recommandés par

Ingersoll-Rand.

• N’utiliser que les douilles et les accessoires pour clés à

chocs. Ne pas utiliser les douilles et accessoires

(chromés) de clés manuelles.

• Cet outil n’est pas conçu pour fonctionner dans des

atmosphères explosives.

• Cet outil n’est pas isolé contre les chocs électriques.

NOTE

L’utilisation de rechanges autres que les pièces d’origine Ingersoll–Rand peut causer des risques d’insécurité, réduire les

performances de l’outil et augmenter l’entretien, et peut annuler toutes les garanties.

Les réparations ne doivent être effectuées que par des réparateurs qualifiés autorisés. Consultez votre Centre de Service

Ingersoll–Rand le plus proche.

SIGNIFICATION DES ÉTIQUETTES D’AVERTISSEMENT

ATTENTION

LE NON RESPECT DES AVERTISSEMENTS SUIVANTS PEUT CAUSER DES BLESSURES.

Porter toujours des lunettes

de protection pendant

l’utilisation et l’entretien de

cet outil.

ATTENTION ATTENTION

Porter toujours une

protection acoustique

pendant l’utilisation de cet

outil.

Les outils pneumatiques

peuvent vibrer pendant

l’exploitation. Les vibrations,

les mouvements répétitifs et les

positions inconfortables

peuvent causer des douleurs

dans les mains et les bras.

N’utiliser plus d’outils en cas

d’inconfort, de picotements ou

de douleurs. Consulter un

médecin avant de recommencer

à utiliser l’outil.

ATTENTION

Ne pas transporter l’outil

par son flexible.

ATTENTION

Garder une position équilibrée et

ferme. Ne pas se pencher trop

en avant pendant

l’utilisation de cet outil.

ATTENTION

Utiliser de l’air comprimé

à une pression maximum

de 6,2 bar (620 kPa).

90 psig

(6.2bar/620kPa)

Couper toujours l’alimentation

d’air comprimé et débrancher le

flexible d’alimentation avant

d’installer, déposer ou ajuster

tout accessoire sur cet outil, ou

d’entreprendre une opération

d’entretien quelconque sur l’ou-

til.

ATTENTION

Ne pas utiliser des flexibles ou

des raccords endommagés,

effilochés ou détériorés.

RÉGLAGES

RÉGLAGE DU COUPLE

Pour ajuster le couple sur ces clés à impulsions à double

palette, procéder comme suit :

1. Déposer le bouchon du trou de réglage.

2. Tourner l’arbre d’entraînement jusqu’à ce que la vis de

réglage de couple soit visible dans l’ouverture.

3. A l’aide d’une clé pour six pans creux de 1,5 mm,

tourner la vis dans le sens des aiguilles d’une montre

pour augmenter le couple de serrage, ou dans le sens

inverse des aiguilles d’une montre pour réduire le

couple. Ne pas tourner le bouchon d’huile.

NOTE

Effectuer tous les réglages finaux sur l’écrou à

serrer.

4. Remonter le bouchon dans le trou de réglage.

CHANGEMENT DU FLUIDE DU MÉCANISME

Le fluide du mécanisme d’impulsion est changé de la façon

1. Déposer la gaine en caoutchouc du corps.

2. A l’aide d’une clé pour six pans creux, déposer les

quatre vis du carter de marteau et les rondelles frein.

Retirer le carter de marteau du corps du moteur sur

l’arbre d’entraînement. Déposer le joint du carter de

marteau.

3. Retirer le mécanisme assemblé du rotor.

4. A l’aide d’une clé pour six pans creux de 2 mm,

tourner la vis de réglage de couple dans le sens des

aiguilles d’une montre jusqu’à ce qu’elle vienne en

butée. Tourner la vis dans le sens inverse des aiguilles

d’une montre jusqu’à ce qu’elle vienne en butée, ou

après six tours complets.

5. A l’aide d’une clé pour six pans creux de 2,5 mm,

dévisser et déposer le bouchon d’huile. Déposer le joint

du bouchon d’huile et la bague d’appui du joint.

6. Tout en tenant le trou du bouchon d’huile vers le bas

au–dessus d’un récipient, tourner l’arbre

d’entraînement pour purger le fluide contenu dans le

mécanisme.

7. Visser la clé en T fournie dans le nécessaire d’outillage

(Réf. No. 1900P–99) dans la butée de piston qui se

trouve à 180_ par rapport à la vis de réglage de couple

et tirer l’ensemble de butée vers la sortie et le

mécanisme jusqu’à ce qu’il s’arrête.

8. A l’aide de la seringue et du fluide fourni dans le

nécessaire de fluide de remplacement (Réf.

No. EQ106S–K400), remplir le mécanisme avec le

fluide fourni jusqu’à ce qu’il déborde du trou de

remplissage. Le Modèle 2400P nécessite 30 cm

fluide et le Modèle 3000P nécessite 43 cm

. Voir Plan

TPD1265.

NOTE

NE PAS UTILISER D’AUTRE FLUIDE. La non

utilisation du fluide fourni pourrait causer

l’endommagement de l’outil, augmenter l’entretien

et réduire les performances. N’utiliser que du fluide

propre dans ces outils.

RÉGLAGES

(Plan TPD1265)

9. Submerger l’ouverture de remplissage dans le reste du

fluide et, à l’aide d’une clé, tourner l’arbre

d’entraînement pour purger tout l’air du système.

10. Retirer le mécanisme du fluide et, à l’aide de la clé en

T, pousser l’ensemble de butée de piston lentement

vers le bas jusqu’à ce que le fluide déborde de

l’ouverture de remplissage.

11. Visser le bouchon, équipé du joint et de son support,

dans le mécanisme et le serrer fermement.

12. A l’aide d’une clé pour six pans creux de 2 mm,

tourner la vis de réglage de couple dans le sens des

aiguilles d’une montre jusqu’à ce qu’elle vienne en

butée. C’est la position de couple maximum.

13. Essuyer l’extérieur du mécanisme pour le sécher et

déposer le bouchon de la chambre d’huile. A l’aide de

la seringue, retirer 0,5 cm

de fluide sur le modèle

2400P et 1 cm

sur le modèle 3000P.

14. Remonter le bouchon de la chambre d’huile et le serrer

à un couple de 2,3 à 2,8 Nm.

15. Placer une nouvelle garniture de carter de marteau sur

le corps de moteur et installer le mécanisme assemblé

sur l’arbre du rotor.

16. Placer le couvercle de carter de marteau sur l’arbre

d’entraînement et contre le corps et son joint. Monter

les quatre vis à six pans creux du carter de marteau et

les rondelles frein. Serrer chaque vis à un couple de

5,1 à 5,6 Nm.

17. Monter la gaine en caoutchouc sur l’outil.

MISE EN SERVICE DE L’OUTIL

LUBRIFICATION

Ingersoll–Rand No.50 Ingersoll–Rand No. 67

Fluide Ingersoll–Rand

Référence EQ106S–400–1

Utiliser toujours un lubrificateur avec ces outils. Nous

recommandons l’emploi du filtre–régulateur–lubrificateur

É. U. – C18–03–FKG0–28

Tous les 20 000 cycles, ou en fonction de l’expérience,

vider et remplir l’ensemble de mécanisme d’impulsion

conformément aux instructions du manuel en utilisant le

nécessaire de fluide de remplacement (Réf. No.

EQ106S–K400). Lubrifier l’entraîneur hexagonal et l’arbre

de sortie avant l’assemblage.

TUYAUTERIE PRINCIPALE

AU MOINS 3 FOIS LA DIMEN-

SION DE L’ADMISSION D’AIR

DE L’OUTIL

VERS LE

RÉSEAU D’AIR

COMPRIMÉ

VERS

L’OUTIL

PNEU-

MATIQUE

LUBRIFICATEUR

RÉGULATEUR

FILTRE

LIGNE SECONDAIRE AU

MOINS 2 FOIS LA DIMEN-

SION DE L’ADMISSION

D’AIR DE L’OUTIL

VIDANGER

RÉGULIÈREMENT

COMPRESSEUR

(Plan TPD905–1)

Toda comunicación se deberá dirigir a la oficina o

al distribuidor Ingersoll–Rand más próximo.

 Ingersoll–Rand Company 2000

Impreso en Japón

MANUAL DE FUNCIONAMIENTO Y MANTENIMIENTO

PARA LLAVES DE IMPULSO DE DOBLE PALETA

MODELOS 2400P Y 3000P

NOTA

Las llaves de impulso modelos 2400P y 3000P está diseñadas para operaciones de ensamblaje

que requieran alta velocidad de atornillado con un par consistente y reducida reacción de par.

Ingersoll–Rand no aceptará responsabilidad alguna por la modificación de las herramientas

efectuada por el cliente para las aplicaciones que no hayan sido consultadas con

Ingersoll–Rand.

AVISO

SE ADJUNTA INFORMACIÓN IMPORTANTE DE SEGURIDAD.

LEA ESTE MANUAL ANTES DE UTILIZAR LA HERRAMIENTA.

ES RESPONSABILIDAD DE LA EMPRESA ASEGURARSE DE QUE EL OPERARIO

ESTÉ AL TANTO DE LA INFORMACIÓN QUE CONTIENE ESTE MANUAL.

EL HACER CASO OMISO DE LOS AVISOS SIGUIENTES PODRÍA OCASIONAR LESIONES.

PARA PONER LA HERRAMIENTA EN SERVICIO

S Utilice, examine y mantenga siempre esta

herramienta conforme al código de seguridad para

herramientas neumáticas portátiles de la American

National Standards Institute (ANSI B186.1).

• Para mayor seguridad, rendimiento óptimo y larga

vida útil de las piezas, utilice esta herramienta a

una presión de aire máxima de 90 psig

(6,2 bar/620 kPa) con una manguera de suministro

de aire con diámetro interno de 13 mm.

• Corte siempre el suministro de aire y desconecte la

manguera de suministro de aire antes de instalar,

desmontar o ajustar cualquier accesorio de esta

herramienta, o antes de realizar cualquier

operación de mantenimiento de la misma.

• No utilice mangueras de aire y racores dañados,

desgastados o deteriorados.

• Asegúrese de que todos los racores y mangueras

sean del tamaño correcto y estén bien apretados.

El Esq. TPD905–1 muestra una disposición

característica de las tuberías.

• Use siempre aire limpio y seco a una presión

máxima de 90 psig (6,2 bar/620 kPa). El polvo, los

gases corrosivos y el exceso de humedad pueden

estropear el motor de una herramienta neumática.

• No lubrique las herramientas con líquidos

inflamables o volátiles tales como queroseno, gasoil

o combustible para motores a reacción.

• No saque ninguna etiqueta. Sustituya toda etiqueta

dañada.

UTILIZACIÓN DE LA HERRAMIENTA

• Use siempre protección ocular cuando utilice esta

herramienta o realice operaciones de

mantenimiento en la misma.

• Use siempre protección para los oídos cuando

utilice esta herramienta.

• Mantenga las manos, la ropa suelta y el cabello

largo alejados del extremo giratorio de la

herramienta.

• Anticipe y esté atento a los cambios repentinos en el

movimiento durante la puesta en marcha y

utilización de toda herramienta motorizada.

• Mantenga una postura del cuerpo equilibrada y

firme. No estire demasiado los brazos al manejar la

herramienta. Pueden darse elevados pares de

reacción a la presión de aire recomendada, e incluso

a presiones inferiores.

• El eje de la herramienta puede seguir girando

brevemente después de haberse soltado el mando.

• Las herramientas neumáticas pueden vibrar

durante el uso. La vibración, los movimientos

repetitivos o las posiciones incómodas pueden

dañarle los brazos y manos. En caso de

incomodidad, sensación de hormigueo o dolor, deje

de usar la herramienta. Consulte con el médico

antes de volver a utilizarla.

• Utilice únicamente los accesorios Ingersoll–Rand

recomendados.

• Utilice únicamente bocas y accesorios para llaves de

impacto. No utilice bocas o accesorios manuales

(cromados).

• Esta herramienta no ha sido diseñada para trabajar

en ambientes explosivos.

• Esta herramienta no está aislada contra descargas

eléctricas.

NOTA

El uso de piezas de recambio que no sean las auténticas piezas Ingersoll–Rand puede poner en peligro la seguridad, reducir

el rendimiento de la herramienta y aumentar los cuidados de mantenimiento necesarios, así como invalidar toda garantía.

Las reparaciones sólo se deben encomendar a personal debidamente cualificado y autorizado. Consulte con el centro de

servicio autorizado Ingersoll–Rand más próximo.

ETIQUETAS DE AVISO

AVISO

EL HACER CASO OMISO DE LOS AVISOS SIGUIENTES PODRÍA OCASIONAR

LESIONES.

ADVERTENCIA

Las herramientas neumáticas

pueden vibrar durante el uso.

La vibración, los movimientos

repetitivos o las posiciones

incómodas podrían dañarle los

brazos y las manos. En caso

de incomodidad, sensación de

hormigueo o dolor, dejar de

usar la herramienta. Consultar

al médico antes de volver a uti-

lizarla.

No coger la herramienta

por la manguera para le-

vantarla.

ADVERTENCIA

Mantener una postura del cuerpo

equilibrada y firme. No estirar de-

masiado los brazos al manejar la

herramienta.

Manejar la herramienta a una

presión de aire máxima de 90

psig (6,2 bar/620 kPa).

90 psig

(6.2bar/620kPa)

Cortar siempre el suministro

de aire y desconectar la man-

guera de suministro de aire

antes de instalar, retirar o ajus-

tar cualquier accesorio de esta

herramienta, o antes de realizar

cualquier operación de man-

tenimiento de la misma.

No utilizar mangueras de aire

y accesorios dañados, des-

gastados ni deteriorados.

ADVERTENCIA

Use siempre protección ocular

cuando utilice esta herramienta

o realice operaciones de

mantenimiento en la misma.

Use siempre protección para

los oídos cuando utilice esta

herramienta.

AJUSTES

AJUSTE DE PAR

Para ajustar el par de estas llaves de impulso de doble

paleta, proceda como sigue:

1. Saque el tapón del orificio de ajuste.

2. Gire el eje de accionamiento hasta que el tornillo de

ajuste de par sea visible a través de dicho orificio.

3. Con una llave hexagonal de 1,5 mm, gire el tornillo de

ajuste de par hacia la derecha para incrementar el par y

hacia la izquierda para disminuirlo. No gire el tapón

del aceite.

NOTA

Haga todos los ajustes finales trabajando.

4. Vuelva a poner en su sitio el tapón del orificio de

ajuste.

CAMBIO DEL LÍQUIDO DEL MECANISMO

Para cambiar el líquido del mecanismo de impulso, proceda

como sigue:

1. Saque la funda de la carcasa de caucho.

2. Utilizando una llave hexagonal, saque los cuatro

tornillos de la caja de mazas y las arandelas de

seguridad. Levante la caja de mazas y sáquela de la

carcasa del motor por encima del eje de accionamiento.

Saque la junta obturadora de la caja de mazas.

3. Levante el mecanismo ensamblado y sáquelo del rotor.

4. Con una llave hexagonal de 2 mm, gire el tornillo de

ajuste de par hacia la derecha hasta que se pare. Gire el

tornillo hacia la izquierda hasta que se pare o dé seis

vueltas completas.

5. Con una llave hexagonal de 2,5 mm, desenrosque y

saque el tapón del aceite. Saque el retén del tapón del

aceite y el soporte de dicho retén.

6. Con el orificio del tapón del aceite apuntando hacia

abajo sobre un contenedor, gire el eje de accionamiento

para purgar el líquido del mecanismo.

7. Enrosque la llave en “T” que se incluye en la caja de

herramientas (Ref. Nº 1900P–99)) en el conjunto del

tope del pistón que se encuentra a 180 grados del

tornillo de ajuste de par, y tire de dicho conjunto hacia

el extremo de salida del mecanismo hasta que se pare.

8. Con la jeringuilla y el líquido del juego de cambio de

líquido (Ref. Nº EQ106S–K400), llene el mecanismo

con el líquido suministrado en dicho equipo hasta que

el líquido se salga del orificio de llenado. El modelo

2400P requerirá 30 cc de líquido, y el modelo 3000P,

43 cc. Vea Esq. TPD1265.

NOTA

NO SUSTITUYA CON NINGÚN OTRO

LÍQUIDO. Si no se usa el líquido de mecanismo

impulsor suministrado, se podría dañar la

herramienta, incrementar su mantenimiento y

disminuir su rendimiento. Use solamente líquido

limpio con estas herramientas.

AJUSTES

(Esq. TPD1265)

9. Sumerja el orificio de llenado en el resto del líquido y,

utilizando una llave, gire el eje de accionamiento para

purgar el aire que pudiera quedar en el sistema.

10. Saque el mecanismo del líquido y utilice la llave en

“T” para empujar lentamente el conjunto de tope del

pistón hacia abajo hasta que el líquido se salga del

orificio de llenado.

11. Enrosque el tapón del aceite con el retén del tapón de

aceite y el soporte del retén en el mecanismo hasta que

quede bien ajustado.

12. Con una llave hexagonal de 2 mm, gire el tornillo de

ajuste de par hacia la derecha hasta que se pare. Ésta es

la posición de máximo par.

13. Limpie la parte de fuera del mecanismo y séquelo, y

saque el tapón de la cámara de aceite. Utilizando la

jeringuilla, saque 0,5 cc de líquido de los modelos

2400P, y 1,0 cc de los modelos 3000P.

14. Instale el tapón de la cámara de aceite y apriételo entre

20 y 25 pulg.–lb (2,3 a 2,8 Nm) de par.

15. Coloque una junta obturadora de la caja de mazas

nueva en la carcasa del motor e instale el mecanismo

ensamblado en el eje rotor.

16. Coloque la cubierta de la caja de mazas sobre el eje de

accionamiento y contra la carcasa y la junta

obturadora. Instale los cuatro tornillos de la caja de

mazas y las arandelas de seguridad. Apriete cada

tornillo entre 45 y 50 pulg–lb ( 5,1 y 5,6 Nm) de par.

17. Instale la funda de la carcasa de caucho en la

herramienta.

PARA PONER LA HERRAMIENTA EN SERVICIO

LUBRICACIÓN

Ingersoll–Rand Nº 50 Ingersoll–Rand Nº 67

Líquido Ingersoll–Rand

Nº EQ106S–400–1

Utilice siempre un lubricador de aire comprimido con estas

herramientas. Recomendamos utilizar el siguiente conjunto

de filtro–lubricador–regulador:

EE.UU. – C11–03–G00

Después de cada 20 000 ciclos, o según indique la

experiencia, drene y vuelva a llenar el conjunto de

accionamiento del mecanismo impulsor tal y como se

indica en este manual, utilizando el juego de cambio de

líquido (Ref. Nº EQ106S–K400). Lubrique el eje de salida

y el de accionamiento hexagonal antes del montaje.

TUBERÍAS PRINCIPALES 3

VECES EL TAMAÑO DE

ENTRADA DE HERRAMIENTA

NEUMÁTICA

AL SISTEMA

NEUMÁTICO

A LA

HERRA–

MIENTA

NEUMÁTICA

LUBRICADOR

REGULADOR

FILTRO

TUBERÍA DE RAMAL

2 VECES EL TAMAÑO

DE ENTRADA DE

HERRAMIENTA

NEUMÁTICA

PURGAR

PERIÓDICAMENTE

COMPRESOR

(Esq. TPD905–1)

Envie Todos os Comunicados Para o Distribuidor

ou Escritório da Ingersoll–Rand Mais Próximo.

 Ingersoll–Rand Company 2000

Fabricado no Japão

MANUAL DE FUNCIONAMENTO E MANUTENÇÃO

PARA FERRAMENTAS

PNEUMÁTICAS DE IMPULSÃO DE LÂMINAS DUPLAS

MODELOS 2400P E 3000P

AVISO

As Ferramentas Pneumáticas de Impulsão Modelos 2400P e 3000P são concebidas para

operações de montagem que exijam velocidade de aperto elevada com torque exercido

consistente e reacção de torque reduzida.

A Ingersoll–Rand não é responsável por modificações feitas pelo cliente em ferramentas nas quais a

Ingersoll–Rand não tenha sido consultada.

ADVERTÊNCIA

INFORMAÇÃO DE SEGURANÇA IMPORTANTE EM ANEXO.

LEIA ESTE MANUAL ANTES DE OPERAR A FERRAMENTA.

É DA RESPONSABILIDADE DO EMPREGADOR COLOCAR A INFORMAÇÃO

DESTE MANUAL NAS MÃOS DO OPERADOR.

O NÃO CUMPRIMENTO DAS SEGUINTES ADVERTÊNCIAS PODE

RESULTAR EM FERIMENTOS.

COLOCANDO A FERRAMENTA

EM FUNCIONAMENTO

S Sempre opere, inspeccione e mantenha esta

ferramenta de acordo com o Código de Segurança

do Instituto Americano de Padrões Nacionais para

Ferramentas Pneumáticas Portáteis (ANSI B186.1).

• Para segurança, máximo desempenho e máxima

durabilidade das peças, opere esta ferramenta com

uma pressão de ar máxima de 6,2 bar/620 kPa

(90 psig) na entrada da mangueira de alimentação

de ar com diâmetro interno de 13 mm (1/2”).

• Desligue sempre a alimentação de ar e desconecte a

mangueira de alimentação de ar antes de instalar,

remover ou ajustar qualquer acessório nesta

ferramenta, ou antes de executar qualquer serviço de

manutenção nesta ferramenta.

• Não use mangueiras de ar ou adaptadores danificados,

gastos ou deteriorados.

• Certifique–se de que todas as mangueiras e

adaptadores sejam do tamanho correcto e estejam

apertados com firmeza. Veja o Desenho TPD905–1

para um arranjo típico de tubagem.

• Use sempre ar seco e limpo com pressão máxima de

6,2 bar/620 kPa (90 psig). Pó, fumos corrosivos e/ou

humidade excessiva podem arruinar o motor de

uma ferramenta pneumática.

• Não lubrifique as ferramentas com líquidos

inflamáveis ou voláteis tais como querosene, diesel ou

combustível de jactos.

• Não remova nenhum rótulo. Reponha qualquer rótulo

danificado.

USANDO A FERRAMENTA

• Use sempre óculos de protecção quando estiver

operando ou executando serviço de manutenção nesta

ferramenta.

• Use sempre protecção contra ruído ao operar esta

ferramenta.

• Mantenha as mãos, partes do vestuário soltas e cabelos

compridos afastados da extremidade em rotação.

• Antecipe e esteja alerta a mudanças repentinas no

movimento quando ligar e operar qualquer

ferramenta motorizada.

• Mantenha a posição do corpo equilibrada e firme. Não

exagere quando operar esta ferramenta. Torques de

reacção elevados podem ocorrer na ou abaixo da

pressão de ar recomendada.

• O eixo da ferramenta pode continuar a girar

brevemente após a pressão ter sido aliviada.

• Ferramentas accionadas pneumáticamente podem

vibrar em uso. Vibração, movimentos repetitivos ou

posições desconfortáveis podem ser prejudiciais às

mãos e aos braços. Pare de usar a ferramenta caso

ocorra algum desconforto, sensação de formigueiro ou

dor. Procure assistência médica antes de retornar ao

trabalho.

• Use acessórios recomendados pela Ingersoll–Rand.

• Use somente soquetes e acessórios de impacto. Não use

soquetes ou acessórios de mão (cromo).

• Esta Ferramenta não foi concebida para trabalhos em

atmosferas explosivas.

• Esta Ferramenta não está isolada contra choques

eléctricos.

AVISO

O uso de peças de substituição que não sejam genuinamente da Ingersoll–Rand podem resultar em riscos de segurança,

diminuição do desempenho da ferramenta, aumento da necessidade de manutenção e pode invalidar todas as garantias.

As reparações devem ser feitas somente por pessoal treinado autorizado. Consulte o Centro de Serviços da Ingersoll–Rand

mais próximo.

IDENTIFICAÇÃO DO RÓTULO DE ADVERTÊNCIA

ADVERTÊNCIA

O NÃO CUMPRIMENTO DAS SEGUINTES ADVERTÊNCIAS PODE

RESULTAR EM FERIMENTOS.

Use sempre óculos de

protecção quando estiver

operando ou executando algum

serviço de manutenção nesta

ferramenta.

ADVERTÊNCIA

Use sempre protecção contra o

ruído ao operar esta ferramenta.

Desligue sempre a alimentação

de ar e desconecte a mangueira

de alimentação de ar antes de

instalar, remover ou ajustar

qualquer acessório nesta

ferramenta, ou antes de

executar algum serviço de

manutenção nesta ferramenta.

Ferramentas accionadas

pneumáticamente podem vibrar

em uso. Vibração, movimentos

repetitivos ou posições

desconfortáveis podem ser

prejudiciais às mãos e aos

braços. Pare de usar a

ferramenta caso ocorra algum

desconforto, sensação de

formigueiro ou dor. Procure

assistência médica antes de

retornar ao trabalho.

Não carregue a ferramenta

segurando na mangueira.

ADVERTÊNCIA

Não use mangueiras de ar ou

adaptadores danificados,

gastos ou deteriorados.

Mantenha a posição do corpo

equilibrada e firme. Não

exagere quando operar esta

ferramenta. Torques de reacção

elevados podem ocorrer sob a

pressão de ar recomendada.

Opere com pressão do ar Máxima

de 90–100 psig (6,2–6,9 bar).

90 psig

(6.2bar/620kPa)

ADVERTÊNCIA

AJUSTES

AJUSTE DE TORQUE

Para ajustar o torque nestas Ferramentas Pneumáticas de

Impulso de Lâminas Duplas, proceda da seguinte maneira:

1. Remova o Bujão do Furo de Ajuste.

2. Gire o Eixo de Comando até o Parafuso de Ajuste de

Torque estar visível na abertura.

3. Usando uma chave Allen de 1,5 mm, gire o Parafuso

de Ajuste no sentido horário para aumentar o torque de

saída e no sentido anti–horário para diminuir o torque

de saída. Não gire o Bujão de Óleo.

AVISO

Faça todos os ajustes finais no serviço.

4. Reponha o Bujão do Furo de Ajuste.

MUDANDO O FLUIDO DO MECANISMO

Para mudar o Fluído do Mecanismo no Mecanismo de

Impulso, proceda da seguinte maneira:

1. Remova o Calço do Corpo de Borracha.

2. Usando uma chave Allen, remova os três Parafusos dos

Tampos da Caixa do Martelo e Anilhas de Trava. Erga

a Caixa do Martelo para fora do Corpo do Motor sobre

o Eixo de Comando. Remova a Junta da Culatra da

Caixa do Martelo.

3. Erga o mecanismo montado do motor.

4. Usando uma chave Allen de 2 mm gire o Parafuso de

Ajuste de Torque no sentido horário até que o Parafuso

pare. Gire o Parafuso no sentido contrário ao dos

ponteiros do relógio até que ele pare ou complete 6

revoluções.

5. Usando uma chave Allen de 2,5 mm, desparafuse e

remova o Bujão de Óleo. Remova o Lacre do Bujão do

Óleo e o Suporte do Lacre do Bujão de Óleo.

6. Com a abertura do bujão de óleo para baixo sobre um

recipiente, gire o Eixo de Comando para expelir o

fluido do mecanismo.

7. Rosqueie a Chave em “T” incluída no Kit de

Ferramenta (Número 1900A–99) no Conjunto de

Paragem do Pistão que está a 180 graus do Parafuso de

Ajuste de Torque e puxe o Conjunto de Paragem em

direção à saída do mecanismo até que ele pare.

8. Usando a seringa e fluído do Kit de Reposição de

Fluído (Número de Pedido EQ106S–K400), encha o

mecanismo com o fluído fornecido no Kit até que o

fluído transborde do orifício de enchimento. O Modelo

2400P necessitará 30 cc de fluído, o Modelo 3000P, 43

cc. Veja o Desenho TPD1265.

AVISO

NÃO SUBSTITUA POR QUALQUER

OUTRO FLUÍDO.

Caso o fluido fornecido não for usado danos podem

ocorrer à ferramenta, aumento da manutenção e

diminuição do desempenho. Use somente fluido

limpo nestas ferramentas.

AJUSTES

(Desenho TPD1265)

9. A abertura de enchimento deve ser submersa no

restante do fluido, e usando uma chave, gire o Eixo do

Comando para expelir qualquer ar remanescente do

sistema.

10. Remova o mecanismo do fluido e use uma Chave em

”T” para empurrar o Conjunto de Paragem do Pistão

lentamente para baixo até que o fluido flua da abertura

de enchimento.

11. Rosqueie o Bujão de Óleo com o Lacre do Bujão de

Óleo no mecanismo até que ele esteja apertado.

12. Usando uma chave Allen de 2 mm, gire o Parafuso de

Ajuste de Torque no sentido horário até o Parafuso

parar. Esta é a posição de aperto máximo.

13. Limpe a parte externa do mecanismo a seco e limpe e

remova o Bujão da Câmara de Óleo. Usando uma

seringa, retire 0,50 cc de fluido do modelo 2400P e

1,0 cc do modelo 3000P.

14. Instale o Bujão da Câmara de Óleo e aperte–o com 2,3

a 2,8 Nm (20 a 25 pol–lb).

15. Posicione a Junta da Culatra da Caixa do Martelo nova

no Corpo do Motor e instale o mecanismo montado no

eixo do rotor.

16. Coloque a Capa da Caixa do Martelo sobre o Eixo de

Comando contra o Corpo e o Junta da Culatra. Instale

os três Parafusos do Tampo da Caixa do Martelo e

Anilhas de Trava. Aperte cada Parafuso com um torque

de 5,1 e 5,6 Nm (45 e 50 pol–lb).

17. Instale o Calço do Corpo de Borracha na ferramenta.

COLOCANDO A FERRAMENTA EM FUNCIONAMENTO

LUBRIFICAÇÃO

Ingersoll–Rand No. 50 Ingersoll–Rand No. 67

Fluído Ingersoll–Rand

Número de Pedido

No. EQ106S–400–1

Use sempre um lubrificador de ar de linha com estas

ferramentas. Nós recomendamos a seguinte Unidade

Filtro–Lubrificador–Regulador:

Para os E.U.A. – No. C18–03–FKG0–28

Depois de cada 20 000 ciclos, ou como a experiência

indicar, drene e encha o Conjunto do Comando da Unidade

de Impulso como instruído neste manual usando o Kit de

Reposição de Fluído (Número de Pedido EQ106S–K400).

Lubrifique o comando hexagonal e o eixo de saída antes de

montar.

LINHAS PRINCIPAIS 3 VEZES O TAMANHO DA

ENTRADA DA FERRAMENTA PNEUMÁTICA

PARA

SISTEMA DE AR

PARA

FERRAMENTA

PNEUMÁTICA

LUBRIFICADOR

REGULADOR

FILTRO

LINHA RAMIFICADA

2 VEZES O TAMANHO

DA ENTRADA DA

FERRAMENTA

PNEUMÁTICA

DRENE

REGULARMENTE

COMPRESSOR

(Desenho TPD905–1)

MAINTENANCE SECTION

(Dwg. TPA1342)

MAINTENANCE SECTION

PART NUMBER FOR ORDERING

2400P 3000P

Motor Housing Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–A40 3000P–A40

1 Motor Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–40 3000P–40

2 Reverse Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000P–328 3000P–328

3 Reverse Lever Retaining Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000P–152 3000P–152

4 Reverse Valve Bushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–330 2400P–330

5 Reverse Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–329 2400P–329

6 Reverse Valve Detent Ball . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500P–333 500P–333

7 Reverse Valve Detent Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–51 1900P–51

8 Reverse Valve Retainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1410P–303 1410P–303

9 Suspension Hole Liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100P–232 1100P–232

10 Throttle Bushing Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ112P–A503 EQ112P–A503

11 Throttle Bushing Seal (3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ106P–283 EQ106P–283

12 Throttle Valve Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ112P–A304 EQ112P–A304

13 Throttle Valve Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ112P–159 EQ112P–159

14 Valve Retaining Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ106P–303 EQ106P–303

15 Throttle Rod Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ112P–A302 EQ112P–A302

16 Throttle Rod Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ106P–288 EQ106P–288

17 Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ106P–93 EQ106P–93

18 Trigger Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ106P–265 EQ106P–265

19 Throttle Retaining Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180PQ–120 180PQ–120

20 Inlet Bushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ106S–565 EQ106S–565

21 Exhaust Deflector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–A23 2400P–A23

Motor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–A53 3000P–A53

Rear End Plate Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–A12 3000P–A12

22 Rear End Plate Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–B12 EQ230P–A12

23 End Plate Alignment Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–152 EQ230P–99

24 Rear Rotor Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R38P–606 EQ230P–24

25 Cylinder Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–A3 3000P–A3

26 Cylinder Alignment Pin (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–152 3000P–152

27 Rotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–53 EQ230P–53

28 Vane Packet (set of 6 Vanes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–42–6 EQ230P–42–6

29 Front End Plate Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–A11 3000P–A11

30 Front Rotor Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–22 2400P–22

MAINTENANCE SECTION

PART NUMBER FOR ORDERING

2400P 3000P

31 Motor Case Cover Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–A202 3000P–A202

32 Suspension Hole Liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100P–232 1100P–232

33 Motor Case Cover Gasket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–739 3000P–739

34 Motor Case Cover Screw (4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–277 3000P–638

35 Cover Screw Lock Washer (4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ112P–58 EQ112P–58

Hammer Case Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–A727 3000P–A727

36 Hammer Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–727 3000P–727

37 Hammer Case Bushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ110P–641 3000P–641

38 Adjustment Hole Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500P–95 500P–95

39 Hammer Case Gasket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–740 3000P–740

40 Hammer Case Cap Screw (4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–277 3000P–638

41 Cap Screw Lock Washer (4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ112P–58 EQ112P–58

42 Dead Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ––– EQ230P–A48

43 Rubber Housing Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–2 3000P–2

44 Nameplate

for models ending in –EU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –––––– 3000P–EU–301

for all other models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–301 3000P–301

* Forward Rotation Label (for models ending in –EU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –––––– 7802R–EU–F99

* Reverse Rotation Label (for models ending in –EU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –––––– 7802R–EU–R99

45 Nameplate Screw (2 for 2400P; 4 for 3000P) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ106S–322 EQ106S–322

46 Warning Label

for models ending in –EU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –––––– EU–99

for all other models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WARNING–2–99 WARNING–2–99

47 Oil Daily Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500P–69 500P–69

48 Two Speed Trigger Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180PQ–68 180PQ–68

* Motor Tune–up Kit (includes illustrated items 24, 28, 30 and 33) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–K500 3000P–K500

* Not illustrated.

MAINTENANCE SECTION

PART NUMBER FOR ORDERING

2400P 3000P

Impulse Unit Drive Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–A200 3000P–A200

49 Liner Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–240 EQ230P–240

Front Cover Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–A211 3000P–A211

50 Front Liner Cover Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–B211 3000P–B211

51 Torque Adjustment Screw . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–230 1900P–230

52 Adjustment Screw Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–288 2400P–288

53 Alignment Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–120 EQ230P–232

54 Oil Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ230P–277 EQ230P–277

55 Oil Plug Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ208S–238 EQ208S–238

56 Oil Plug Seal Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ230P–229 EQ230P–229

57 Drive Shaft O–ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ110P–271 EQ230P–271

58 Seal Back–up Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ110P–272 EQ230P–272

59 Front Liner Cover Piston Seal (2) . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–237 3000P–236

60 Liner Housing Seal (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–238 3000P–238

Drive Shaft Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–A626 –––

61 Drive Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–626 3000P–626

62 Socket Retaining Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 804–716 –––

63 Retaining Pin Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5HUD–718 –––

64 Drive Shaft Blade (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–220 EQ230P–220

65 Blade Spring (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–219 EQ230P–219

66 Liner Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–A203 3000P–A203

67 Liner Alignment Pin (4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–298 EQ230P–298

68 Torque Valve Piston . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–222 EQ230P–222

Piston Stop Assembly (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–A255 EQ230P–A255

69 Piston Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–255 EQ230P–255

70 Piston Stop Seal (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ104S–50 EQ230P–288

71 Piston Stop Assist Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–219 1900P–219

72 Rear Liner Cover Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–238 3000P–237

73 Rear Liner Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–212 EQ230P–212

74 Housing Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ112P–207 EQ230P–207

* Fluid Replacement Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ106S–K400 EQ106S–K400

* Replacement Fluid (4 oz.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ106S–400–1 EQ106S–400–1

* Mechanism Tune–up Kit (includes illustrated

items 55, 56, 57, 58, 59 [2], 60 [2], 70 [2] and 72) . . . . . . . . . . . . . . . 1900P–K600 –––

* Mechanism Tune–up Kit (includes illustrated

items 39, 55, 56, 57, 58, 59 [2], 60 [2], 65 [2], 70 [2], 71 and 72) . . . ––– 3000P–K600A

* Tool Kit (includes all the specialized tooling required to repair

these tools and consists of a Spanner Plug, Threaded Tee Wrench,

O–ring Installer and a pressing fixture that has a Disassembly

Arbor and Pressing Sleeve) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900P–99 1900P–99

* Not illustrated.

MAINTENANCE SECTION

CHANGING THE MECHANISM FLUID

To change the Mechanism Fluid in the Impulse

Mechanism, proceed as follows:

1. Remove the Rubber Housing Boot (43).

2. Using a hex wrench, remove the four Hammer Case

Cap Screws (40) and Lock Washers (41). Lift the

Hammer Case (36) off the Motor Housing (1) over the

Drive Shaft. Remove the Hammer Case Gasket (39).

3. Lift the assembled mechanism off the Rotor (27).

4. Using a 2 mm hex wrench, rotate the Torque

Adjustment Screw (51) clockwise until the Screw

stops. Rotate the Screw counterclockwise until it

stops or makes six complete revolutions.

5. Using a 2.5 mm hex wrench, unscrew and remove the

Oil Plug (54). Remove the Oil Plug Seal (55) and

Oil Plug Seal Support (56).

6. With the oil plug opening downward over a container,

rotate the Drive Shaft to purge the fluid from the

mechanism.

7. Thread the Tee Wrench included with the Tool Kit

(Part No. 1900P–99) into the Piston Stop Assembly

(69) that is 180 degrees from the Torque Adjustment

Screw and pull the Stop Assembly toward the output

end of the mechanism until it stops.

8. Using the syringe and fluid from the Fluid

Replacement Kit (Part No. EQ106S–K400), fill the

mechanism with the fluid furnished in the Kit until

the fluid overflows the fill hole. Model 2400P will

require 30 cc of fluid, Model 3000P, 43 cc.

(Refer to Dwg. TPD1265)

DO NOT SUBSTITUTE ANY OTHER FLUID.

Failure to use the impulse mechanism fluid

provided could damage the tool, increase

maintenance and decrease performance. Use only

clean fluid in these tools.

(Dwg. TPD1265)

9. Submerge the fill opening in the remainder of the

fluid, and using a wrench, rotate the Drive Shaft to

purge any remaining air from the system.

10. Remove the mechanism from from the fluid and use

the Tee Wrench to push the Piston Stop Assembly

slowly downward until fluid flows from the fill

opening.

11. Thread the Oil Plug with the Oil Plug Seal and Seal

Support into the mechanism until it is snug.

12. Using a 2 mm hex wrench, turn the Torque

Adjustment Screw clockwise until it stops. This is the

maximum torque position.

13. Wipe the outside of the mechanism dry and clean and

remove the Oil Chamber Plug. Using the syringe,

withdraw 0.5 cc of fluid from 2400P models and 1.0

cc from 3000P models.

14. Install the Oil Chamber Plug and tighten it between

20 and 25 in–lb (2.3 and 2.8 Nm) torque.

15. Position a new Hammer Case Gasket on the Motor

Housing and install the assembled mechanism on the

rotor shaft.

16. Place the Hammer Case Cover over the Drive Shaft

against the Housing and Gasket. Install the four

Hammer Case Cap Screws and Lock Washers.

Tighten each Screw between 45 an 50 in–lb (5.1 and

5.6 Nm) torque.

17. Install the Rubber Housing Boot on the tool.

DISASSEMBLY

General Instructions

1. Do not disassemble the tool any further than

necessary to replace or repair damaged parts.

2. When grasping a tool or part in a vise, always use

leather–covered or copper–covered vise jaws to

protect the surface of the part and help prevent

distortion. This is particularly true of threaded

members and housings.

3. Do not remove any part which is a press fit in or on

an assembly unless the removal of that part is

necessary for repairs or replacement.

Disassembly of the Impulse Mechanism

1. Use a hooked wire to pull the Retaining Pin Spring

(63) out of the end of the Drive Shaft (61) and remove

the Socket Retaining Pin (62).

2. Remove the Rubber Housing Boot (43).

3. Using a hex wrench, remove the four Hammer Case

Cap Screws (40) and Lock Washers (41). Lift the

Hammer Case (36) off the Motor Housing (1) over the

Drive Shaft. Remove the Hammer Case Gasket (39).

4. Lift the assembled mechanism off the Rotor (27).

5. Grasp the flats of the Housing (49) in vise jaws with

the output end of the Drive Shaft downward.

MAINTENANCE SECTION

6. Insert the pins of the Spanner Plug from the No.

1900P–99 Tool Kit into two holes in the Housing

Cap (74). Using a wrench on the plug, unscrew and

remove the Housing Cap from the Housing.

(Refer to Dwg. TPD1267.)

It may be necessary to cut the thread sealant

around the Housing Cap with a sharp knife before

attempting to remove the Cap.

(Dwg. TPD1267)

SPANNER PLUG

COUNTERCLOCKWISE TO LOOSEN

7. Stand the Disassembly Arbor from the Tool Kit, large

end downward, on a workbench or the table of an

arbor press. Insert the output end of the Drive Shaft

into the central opening and either tap the Housing

downward off the components or use the Pressing

Sleeve in the Kit to press the Housing downward off

the components. (Refer to Dwg. TPD1268.)

(Dwg. TPD1268)

PRESSING SLEEVE

TAP EDGE LIGHTLY WITH

BRASS HAMMER OR USE

PRESSING SLEEVE FROM

TOOL KIT

DISASSEMBLY ARBOR FROM

TOOL KIT

8. Disassemble the components of the mechanism in the

sequence shown in Drawing TPA1342 on Page 4.

Disassembly of the Motor

1. Grasp the Motor Housing (1) in vise jaws with the

Motor Case Cover Assembly (31) upward.

2. Using a hex wrench, remove the four Motor Case

Cover Screws (34) and Lock Washers (35).

3. Remove the Cover and Motor Case Cover Gasket (33)

from the Motor Housing.

4. Remove the Housing from the vise jaws and insert a

rod into the central opening in the output end of the

rotor shaft.

5. While holding the motor end of the Housing above a

piece of cardboard on the workbench, lightly tap the

rod to remove the Rear End Plate Assembly (22),

Rotor (27) and Vanes (28).

6. On the table of an arbor press, support the Rear End

Plate with blocks as close to the Rotor as possible and

press the Rotor out of the Rear End Plate and Rear

Rotor Bearing (24).

7. To remove the Rear Rotor Bearing from the Rear End

Plate, use a small drift or pin punch through the

central opening of the Rear End Plate to tap the

Bearing out of the End Plate. (Refer to Dwg.

TPD1271.)

Do not enlarge or damage the shaft hole in the End

Plate.

(Dwg. TPD1271)

8. Using a longer drift punch through the Cylinder (25),

tap the Front Rotor Bearing (30) out of the Front End

Plate Assembly (29) in the same manner.

Do not enlarge or damage the shaft hole in the End

Plate.

9. The Cylinder and Front End Plate are a shrink fit in

the Motor Housing and parts that can be damaged

during the heating process must be removed before

heating the Housing.

10. Press the Reverse Lever Pin (3) out of the Reverse

Lever (2) and pull the lever off the shaft of the

Reverse Valve (5).

11. Using snap ring pliers, remove the Reverse Valve

Retainer (8).

12. Grasp the shaft of the Reverse Valve with pliers, and

pull the Reverse Valve, Reverse Valve Detent Ball (6)

and Detent Spring (7) out of the Reverse Valve

Bushing (4). Be careful not to lose the Ball and

Spring.

13. Using a pin punch, tap the Throttle Retaining Pin (19)

out of the Handle.

MAINTENANCE SECTION

14. Grasp the Trigger (17) and pull the assembled throttle

out of the Motor Housing.

15. Using a pin punch and without damaging the Trigger,

remove the Trigger Pin (18).

16. Slide the Throttle Bushing Assembly (10) off the shaft

of the Throttle Rod Assembly (15).

17. Using a thin blade screwdriver, remove the Valve

Retaining Ring (14) and slide the Throttle Valve

Assembly (12) off the shaft of the Throttle Valve Rod.

18. Using an adjustable wrench, unscrew and remove

the Inlet Bushing (20) and Exhaust Deflector

Assembly (21).

19. Insert a threaded rod through the Cylinder and Front

End Plate and install a nut and washer on the end

plate end of the rod. Position the Rear End Plate on

the threaded rod against the Cylinder and clamp the

End Plates and Cylinder snug with another nut and

washer. Do not tighten the assembly excessively.

20. Using a heat induction coil or an oven, heat the

assembly and Housing until it is warm enough to pull

the assembly out the rear of the Motor Housing. Do

not apply enough heat to distort the Housing.

Take all precautions necessary to prevent being

burned by handling warm or hot parts.

ASSEMBLY

General Instructions

1. When grasping a tool or part in a vise, always use

leather–covered or copper–covered vise jaws to

protect the surface of the part and help prevent

distortion. This is particularly true of threaded

members and housings.

2. Always press on the inner ring of a ball–type bearing

when installing the bearing on a shaft.

3. Always press on the outer ring of a ball–type bearing

when pressing the bearing into a bearing recess.

4. Except for bearings and mechanism parts, always

clean every part and wipe every part with a thin film

of oil before installation.

5. Wipe a thin film of mechanism fluid on all internal

mechanism components before installing them in the

mechanism.

6. Apply a film of O–ring lubricant to every O–ring

before installation.

Assembly of the Motor

1. Using an arbor press and a piece of tubing that

contacts the outer ring of the bearings, press the Front

Rotor Bearing (30) into the Front End Plate (29) and

the Rear Rotor Bearing (24) into the Rear End Plate

(22). (Refer to Dwg. TPD1274.)

(Dwg. TPD1274)

TUBING

BEARING

END PLATE

2. Stand the Rotor (27) on the table of an arbor press. It

should be upright on a flat metal plate having a

clearance hole for the shaft. The shaft with the hex

must be upward.

3. Place a 0.001” (0.025 mm) shim on the upward

surface of the large portion of the rotor body. Using a

piece of tubing that contacts the inner ring of the

bearing, press the Front Rotor Bearing and Front End

Plate, End Plate leading, onto the shaft of the Rotor

until the End Plate contacts the shim. Remove the

shim. (Refer to Dwg. TPD1275.)

(Dwg. TPD1275)

PRESSING PLUG

FRONT ROTOR BEARING

ROTOR

PLATE WITH ROTOR

SHAFT CLEARANCE

FRONT END PLATE

0.001” (0.025 mm)

SHIM SPACE

4. Coat each Vane (28) with a thin film of oil and insert

a Vane into each of the rotor vane slots with the

straight edge of the Vane outward.

5. Install the Cylinder Assembly (25) over the Vanes and

Rotor making certain the Cylinder Alignment Pin (26)

enters the hole in the face of the Front End Plate.

6. Stand the assembly on an arbor press table so that the

rotor shaft on the front end plate end contacts the

table. Press the Rear End Plate Assembly, bearing end

trailing, onto the rotor shaft against the Cylinder.

Make certain the Cylinder Alignment Pin (26) enters

the hole in the face of the Rear End Plate.

7. Stand the assembly on a table with the Front End

Plate Assembly upward.

MAINTENANCE SECTION

8. Using an induction coil or oven, heat the Motor

Housing until the motor opening is large enough to be

placed over the Cylinder. At that time, install the

Housing over the Cylinder and Front End Plate

making sure the radial End Plate Alignment Pin (23)

in the Rear End Plate enters the notch in the Motor

Housing.

Take all precautions necessary to prevent being

burned by handling warm or hot parts.

9. Allow the assembly to cool and install the Motor Case

Cover Gasket (33) and Motor Case Cover (31).

10. Secure the Cover to the Housing by installing the four

Motor Case Cover Screws (34) and Lock Washers

(35). Tighten each Screw between 45 and 50 in–lb

(5.1 and 5.6 Nm) torque.

11. Install the Exhaust Deflector (21) in the bottom of the

handle of the Motor Housing (1) and tighten it

between 20 and 25 ft–lb (27 and 34 Nm) torque.

12. Thread the Inlet Bushing (20) into the bottom of the

handle of the Motor Housing and tighten it between

30 and 35 ft–lb (40 and 47 Nm) torque.

13. Install the Throttle Rod Seal (16) in the groove on the

large hub of the Throttle Rod (15).

14. Install the Throttle Valve Seal (13) in the groove on

the large hub of the Throttle Valve (12).

15. Slide the Throttle Valve, Valve Seal end first, onto the

Throttle Valve Rod.

16. Secure the Throttle Valve Assembly by installing the

Valve Retaining Ring (14) in the small groove on the

Throttle Valve Rod.

17. Install the three Throttle Bushing Seals (11) in the

grooves on the Throttle Bushing (10).

18. Slide the Throttle Bushing Assembly onto the shaft of

the Throttle Valve Rod and position the Trigger (17)

on the same shaft. Install the Trigger Pin (18).

19. Insert the assembled Trigger into the Housing. Make

certain the widest end of the Trigger is nearest the

motor bore and the narrowest portion of the Throttle

Valve aligns with hole for the Throttle Retaining Pin

(19). Install the Pin making certain it captures the

Throttle Valve and secures the assembled Trigger.

20. Align the detent hole in the Reverse Valve (5) with

the hole inside the Reverse Valve Bushing (4) and

slide the Valve into the Bushing until almost reaching

the detent hole. Insert the Reverse Valve Detent

Spring (7) and Reverse Valve Detent Ball (6) into the

hole and while compressing the Spring with the Ball,

slide the Valve completely into the Bushing.

21. Using snap ring pliers, install the Reverse Valve

Retainer (8).

22. Slide the Reverse Lever (2) onto the Reverse Valve,

making certain the cast lug enters the notch on the

face of the Reverse Valve Bushing. Secure the Lever

to the Valve by inserting the Reverse Lever Retaining

Pin (3).

Assembly of the Impulse Mechanism

1. Insert the long shaft of the Piston Stop (69) into the

central opening of the O–ring Installer furnished with

the Tool Kit (Part No. 1900P–99). Place the Piston

Stop Seal (70) on the tapered end of the Installer and

roll the Seal up the taper and into the groove on the

large body of the Piston Stop. Repeat the procedure

with the other Piston Stop and Seal.

2. When looking inside the central opening of the Liner

Assembly (66), the internal wall has three holes on

one side which do not extend through the wall. The

opening on the end face of that wall is for the Torque

Valve Piston (68). Install the Torque Valve Piston,

large end trailing, into that opening.

3. Insert the Piston Stop Assist Spring (71) into the hole

in the end face of the opposite wall.

4. Thread the Threaded Tee Wrench furnished with the

Tool Kit into one of the Piston Stop Assemblies and

using the Wrench to hold the Assembly, insert the

Assembly into the opening against Piston. Mark this

opening with a felt marker to indicate that it contains

the Torque Valve Piston.

5. Unscrew the Wrench and in the same manner, install

the other Piston Stop Assembly in the hole with the

Spring.

6. Install the Rear Liner Cover Seal (72) in the annular

groove on the face of the Rear Liner Cover (73).

7. Install the two Front Liner Cover Piston Seals (59) in

the openings on the face of the Front Liner Cover

(50).

8. Install the Seal Back–Up Ring (58) followed by the

Drive Shaft O–ring (57) in the central opening in the

face of the Front Liner Cover.

9. Insert the short round hub of the Drive Shaft (61) into

the central opening of the Rear Liner Cover.

10. Insert a Blade (64) into one slot in the Drive Shaft.

Install the Blade Springs (65) through the Drive Shaft

and into the holes in the Blade. Place the remaining

Blade on the Springs making certain the Springs enter

the holes in that Blade.

11. Using finger pressure, compress the Springs with the

Blades until the outer edges of the Blades are flush

with the drive shaft surface. Capture the Blades in

thisposition by installing the Liner Assembly, piston

stop end trailing, over the Drive Shaft and against the

Rear Liner Cover.

La page charge ...

Ingersoll-Rand 3000P Operation and Maintenance Manual

Marque: Ingersoll-Rand

Modèle: 3000P

Catégorie: Outils électroportatifs

Taper: Operation and Maintenance Manual

Ce manuel convient également à

2400P

Télécharger le PDF

rapport

Ingersoll-Rand 3000P Operation and Maintenance Manual

Ce manuel convient également à

Ingersoll-Rand 3000P Operation and Maintenance Manual

dans d''autres langues

Documents connexes

Autres documents