Whirlpool WRS312SNHW Mode d'emploi

Marque: Whirlpool

Modèle: WRS312SNHW

Catégorie: Frigos

Taper: Mode d'emploi

Table of Contents/Table des matières

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

Side by Side Refrigerator

Do Not Throw Away - Additional important safety information included.

Para las instrucciones en español, visite nuestro sitio de internet.

INSTRUCTIONS D’INSTALLATION

ET MANUEL D’UTILISATION

Réfrigérateur côte à côte

Ne pas jeter — Autres consignes de sécurité importantes ci-jointes.

REFRIGERATOR SAFETY .............................................................. 2

INSTALLATION INSTRUCTIONS ................................................... 3

Unpack the Refrigerator ............................................................... 3

Door Removal, Leveling, and Alignment .....................................4

Handle Installation and Removal .................................................6

Location Requirements ................................................................7

Electrical Requirement .................................................................7

Water Supply Requirements ........................................................7

Connect Water Supply .................................................................8

REFRIGERATOR CARE ...............................................................10

Cleaning .....................................................................................10

Lights ..........................................................................................11

Vacation and Moving Care .........................................................11

TROUBLESHOOTING ..................................................................12

PERFORMANCE DATA SHEET ...................................................17

SÉCURITÉ DU RÉFRIGÉRATEUR...............................................18

INSTRUCTIONS D’INSTALLATION .............................................19

Déballage du réfrigérateur .........................................................19

Retrait, réglage de l’aplomb et alignement des portes .............20

Installation et dèmontage des poignèes ....................................22

Exigences d’emplacement .........................................................23

Spéciﬁcations électriques ..........................................................23

Spéciﬁcations de l’alimentation en eau .....................................23

Raccordement de la canalisation d’eau ....................................24

ENTRETIEN DU RÉFRIGÉRATEUR ............................................26

Nettoyage ...................................................................................26

Lampes .......................................................................................27

Entretien avant les vacances ou lors d’un déménagement ......27

DÉPANNAGE .................................................................................28

FEUILLE DE DONNÉES SUR LA PERFORMANCE ...................34

W11105301A

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

REFRIGERATOR SAFETY

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

SAVE THESE INSTRUCTIONS

■ Plug into a grounded 3 prong outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Connect to a potable water supply only.

■ Use nonflammable cleaner.

■ Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

■ Use two or more people to move and install refrigerator.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ Use a sturdy glass when dispensing ice (on some models).

■ Do not hit the refrigerator glass doors (on some models).

■ This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their

safety.

■ Children should be supervised to ensure that they do not

play with the appliance.

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

Proper Disposal of

Your Old Refrigerator

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not

problems of the past. Junked or abandoned refrigerators are

still dangerous—even if they will sit for “just a few days.” If

you are getting rid of your old refrigerator, please follow these

instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the oor with

cardboard or hardboard to avoid oor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

“walk” the refrigerator when trying to move it, as oor

damage could occur.

Remove packing materials. Do not use sharp instruments,

rubbing alcohol, ﬂammable ﬂuids, or abrasive cleaners to

remove tape or glue. These products can damage the surface of

your refrigerator. For more information, see “Refrigerator Safety.”

Door Removal, Leveling, and Alignment

Gather the required tools and parts and read all instructions before starting installation. Save these instructions for future reference.

NOTE: Before moving your product into your home, measure the doorway of your home to see whether you need to remove the

refrigerator and freezer doors. If door removal is necessary, see the instructions below.

IMPORTANT: Before you begin, unplug refrigerator or disconnect power. Remove food, the ice storage bin (on some models), and

any adjustable door or utility bins from doors.

TOOLS NEEDED: Bubble level; ﬂat-blade screwdriver; 5/16" and 11/16" wrench; 1/4", 3/8", and 5/16" hex-head socket wrenches,

TORX

T30

®†

screwdriver.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Do not remove A screws

A CB

A. Wiring plugs

B. Wiring clip

C. Grommets

A. Face of ﬁtting

A. Pull to the right for extraction.

B. Twist and pass underneath door.

Pull toward you.

Raise

Lower

5/16"

wrench

Tighten

Loosen

11/16"

wrench

Raise

Lower

Raise

Do not remove B screws

†TORX® and T30 are registered trademarks of Acument Intellectual Properties, LLC.

Full Refrigerator

Left and Right Bottom Hinge

Door Removal

Top Left Hinge

Wiring

Water Dispenser

Tubing

Base Grille

Water Filter Door and

Base Grille

Alignement Screw

Locking Nut

Leveling screws

Do not remove A screws

Top Right Hinge

Cabinet

Freezer

door

Water

ﬁlter door

Base

grille

Refrigerator

door

Adjustable front wheels

Remove the Doors

If your refrigerator does not ﬁt through the doorway or you are

getting rid of your old refrigerator, follow the steps below for

door removal.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Fully open both doors. See graphic 1.

3. If your model has water dispensing, please open the water

ﬁlter door by pulling it toward you. See graphic 2. It is not

necessary to remove the water ﬁlter itself.

4. Pull the base grille toward you from the sides and then from

the center until it dislodges. See graphic 2.

5. To remove the base grille, twist and pull the right side

until this side passes underneath the refrigerator door.

See graphic 3. Then pull the left side of the base grille for

complete removal.

6. If your model has water dispensing in the door, disconnect

the water dispenser tubing located below the freezer door.

■ Press the blue outer ring against the face of ﬁtting and

pull the dispenser tubing free. See graphic 4.

NOTE: Keep the water tubing connector attached to the

tube that runs underneath the freezer. The door cannot

be removed if the connector is still attached to the tube

that runs through the door hinge.

7. If your model has water dispensing in the door, disconnect

the wiring located below the freezer door. See graphic 5.

■ Remove the wiring clip and the bracket wire using a 1/4"

hexagonal head socket wrench.

■ Disconnect the wiring plugs from the bracket wire.

8. Close the freezer door and use a TORX

T30

screwdriver

to remove the top hinge completely. See graphic 6.

IMPORTANT: Do not remove either screw A. Hold the door

while hinge is being removed.

9. Lift the freezer door straight up off from the bottom hinge.

See graphic 7. The water dispenser tubing and wiring will

remain attached to the freezer door.

NOTE: This may require two people, one to lift the door and

another to feed the water tubing and wiring into the bottom

hinge pin.

IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket, or piece of cardboard. This

will help to avoid scratching or damaging the door, water

tubing, and wiring.

10. Close the refrigerator door and use a TORX

T30

screwdriver to remove completely top hinge. See graphic 8.

IMPORTANT: Do not remove either screw A. Hold the door

while hinge is being removed.

11. Lift the refrigerator door straight up off from the bottom

hinge. See graphic 7.

IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket, or piece of cardboard.

This will help to avoid scratching or damaging the door.

12. If your refrigerator without doors does not pass through the

doorway, you may remove both bottom hinges. Use a 5/16"

nut driver to remove these. See graphic 9.

IMPORTANT: Do not remove either screw B.

Replacing or Reinstalling Door and Hinges

If your doors and bottom hinges have been removed, please

follow the next instructions for reinstallation:

1. Reinstall both bottom hinges using a 5/16" nut driver to

tighten screws. See graphic 9.

2. If your model has water dispensing in the door:

■ Lift the freezer door enough to feed the water dispenser

tubing and wiring through the bottom hinge pin.

NOTE: This may require two people, one to lift the door

and the other to feed the water tubing and wiring into the

bottom hinge pin. See graphic 7.

■ Insert the freezer door into the bottom hinge pin.

IMPORTANT: Hold the door while hinge is being installed

3. Close the freezer door to align and reinstall the top hinge.

Use a TORX

T30

screwdriver to tighten the screws. See

graphic 8.

IMPORTANT: Provide additional support for the door while

top hinge is being reinstalled. Do not depend on the door

magnets to assure the door to the cabinet.

4. If your model has water dispensing in the door, connect the

water dispenser tubing. For the connection, push the tubing

into the dispenser tubing until black mark touches the face of

ﬁtting. See graphic 4.

5. Connect the wiring. See graphic 5.

6. Reinstall the wiring clip & the bracket wire using a 1/4"

hexagonal head socket wrench.

7. Connect the wiring plugs from the bracket wire.

8. Lift the refrigerator door enough to insert the door into the

bottom hinge pin. See graphic 7.

IMPORTANT: Hold the door while hinge is being installed.

9. Close the refrigerator door to align and reinstall the top

hinge. Use a TORX

T30

screwdriver to tighten the screws.

See graphic 6.

IMPORTANT: Provide additional support for the door while

top hinge is being reinstalled. Do not depend on the door

magnets to assure the door to the cabinet.

Leveling and Door Closing

Your refrigerator has two front adjustable wheels. See graphic 1.

These are used to level the refrigerator under uneven ﬂoor

conditions or want the doors to close more easily. Please follow

the instructions below:

1. Place the refrigerator into its ﬁnal location in the kitchen and

open both doors.

2. Fully open both doors. See graphic 1.

3. If your model has water dispensing in the door, please open

the water ﬁlter door by pulling it toward you. See graphic 2. It

is not necessary to remove the water ﬁlter itself.

4. Pull the base grille toward you from the sides and then from

the center until it dislodges. See graphic 2.

5. To remove the base grille, twist and pull the right side

until this side passes underneath the refrigerator door.

See graphic 3. Then pull the left side of the base grille for

complete removal.

6. Use a 3/8" nut driver to turn the leveling screws located in

both sides of the refrigerator. See graphic 10. Depending

on uneven ﬂoor conditions, you must turn one or both

screws to the right or left several times to raise or lower the

refrigerator. Until the refrigerator is steady, use a bubble level

if necessary.

7. Close both doors and check that they close as easily as

you like. If not, turn both screws to the right to raise the

refrigerator by tiling it more to the back until the doors close

as easily as you like.

8. Check and make sure to the technician sheet is placed in the

base grille cavity before assembling this into the cabinet.

9. Reinstall the base grille into the cabinet, introducing the

left side ﬁrst and then the right side of the base grille. See

graphic 3. You may accommodate the water dispenser

tubing and wiring into base grille cavity below the left bottom

hinge.

10. Attach the base grille pushing into the cabinet clips. See

graphic 2.

Door Alignment

The refrigerator doors are designed to be slightly misaligned

vertically when the refrigerator is empty. Please follow the next

steps to align the refrigerator doors.

1. Use an 11/16" open-ended wrench tool to loosen the locking

nut located below the refrigerator door. See graphic 11.

Accommodate the wrench tool so that it ﬁts in the space.

2. Use a 5/16" open-ended wrench tool to turn the alignment

screw. See picture 12. Depending on how the refrigerator

door is misaligned in relation to the freezer door, you must

turn the screw to the right to raise or to the left to lower

the refrigerator door until both doors have been aligned

vertically.

3. Tighten the 11/16" locking nut with the wrench tool.

4. Attach the base grille if it was dislodged.

Handle Installation and Removal

PARTS INCLUDED: Door handles (2), 1/8" hex key, spare

setscrew(s)

To Install the Handles:

NOTE: The handle mounting setscrews are preinstalled in the

handle.

1. Remove the handles, which are packed inside the

refrigerator.

NOTE: To avoid scratching the ﬁnish, place the handles on

a towel or other soft surface.

2. Open the freezer door. On the refrigerator door, place the

handle on the shoulder screws with the setscrews facing

the freezer.

A. Shoulder screws

B. Setscrews inside the handle

3. Firmly push the handle toward the door until the handle base

is ﬂush against the door.

4. While holding the handle, insert the short end of the hex key

into the upper hole and slightly rotate the hex key until it is

engaged in the setscrew.

5. Using a clockwise motion, tighten the setscrew until it begins

to contact the shoulder screw.

6. Repeat steps 4 and 5 to begin fastening the lower setscrew.

7. Once both setscrews have been partially tightened as

outlined in the previous steps, fully tighten both the upper

and lower setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

8. Open the refrigerator door and close the freezer door. Repeat

steps 2 through 7 to install the other handle onto the freezer

door with the setscrews facing the refrigerator.

9. Save the hex key and all instructions.

To Remove the Handles:

1. While holding the handle, insert the short end of the hex key

into the lower setscrew hole and slightly rotate the hex key

until it is engaged in the setscrew.

2. Using a counterclockwise motion, loosen the setscrew a

quarter-turn at a time.

3. Repeat steps 1 and 2 for the upper setscrew. Gently pull the

handle away from the door.

4. If necessary, use a Phillips screwdriver to remove the

shoulder screws from the door.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor household

use only.

To ensure proper ventilation for your refrigerator, allow for 1/2"

(1.27 cm) of space on each side and at the top. Allow for 2"

(5.08 cm) of space behind the refrigerator. If your refrigerator

has an ice maker, allow extra space at the back for the water

line connections. When installing your refrigerator next to a

ﬁxed wall, leave a 2" (5.08 cm) minimum space on each side

(depending on your model) to allow the doors to swing open.

2" (1.27 cm)

2" (5.08 cm)

NOTES:

■ This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature

range for optimum performance, which reduces electricity

usage and provides superior cooling, is between 60°F (15°C)

and 90°F (32°C). It is recommended that you do not install

the refrigerator near a heat source, such as an oven or

radiator.

■ Normal minimum cabinet cut-out width required for product

installation is 36" (91.44 cm). However, if the product is

placed against an extended wall and the ability to remove

the crisper pans is desired, an additional 18" (45.72 cm) of

cabinet width is required, so a total cabinet opening width of

54" (137.16 cm) is recommended.

Electrical Requirement

Before you move your refrigerator into its ﬁnal location, it

is important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115-volt, 60 Hz, AC-only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an extension

cord.

NOTE: Before performing any type of installation or cleaning,

or removing a light bulb, disconnect the refrigerator from

the electrical source. When you are ﬁnished, reconnect the

refrigerator to the electrical source and reset the control

(Thermostat, Refrigerator or Freezer Control depending on the

model) to the desired setting. See the “Using the Controls”

section in the User Instructions, User Guide, or Use and Care

Guide.

Water Supply Requirements

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

■ Flat-blade screwdriver

■ 7/16" and 1/2" open-end or two adjustable wrenches

■ 1/4" nut driver

■ 1/4" drill bit

■ Cordless drill

NOTE: Your refrigerator dealer has a kit available with a 1/4"

(6.35 mm) saddle-type shut-off valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes. Do not use a piercing-

type or 3/16" (4.76 mm) saddle valve which reduces water ﬂow

and clogs more easily.

IMPORTANT:

■ All installations must meet local plumbing code

requirements.

■ Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 and 827 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your

water pressure, call a licensed, qualiﬁed plumber.

■ If your refrigerator has a water dispenser: After installation

is complete, use the water dispenser to check the water

pressure.

■ With the water ﬁlter removed, dispense 1 cup (237 mL) of

water. If 1 cup of water is dispensed in 8 seconds or less,

the water pressure to the refrigerator meets the minimum

requirement.

■ If it takes longer than 8 seconds to dispense 1 cup of

water, the water pressure to the refrigerator is lower than

recommended. See “Troubleshooting” for suggestions.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out

of a reverse osmosis system going to the water inlet valve of

the refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water ﬁltration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment ﬁlter in the reverse

osmosis system is blocked. Replace the ﬁlter if necessary.

■ Allow the storage tank on the reverse osmosis system to reﬁll

after heavy usage.

■ If your refrigerator has a water ﬁlter, it may further reduce

the water pressure when used in conjunction with a reverse

osmosis system. Remove the water ﬁlter. See “Water

Filtration System” in the User Instructions, User Guide, or

Use and Care Guide.

If you have questions about your water pressure, call a licensed,

qualiﬁed plumber.

Connect Water Supply

Read all directions before you begin.

IMPORTANT:

■ Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

■ The gray water tubing on the back of the refrigerator

(which is used to connect to the household water line) is

a PEX (cross-linked polyethylene) tube. Copper and PEX

tubing connections from the household water line to the

refrigerator are acceptable, and will help avoid off-taste

or odor in your ice or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend

the following Whirlpool Part Numbers:

W10505928RP (7 ft [2.14 m] jacketed PEX),

8212547RP (5 ft [1.52 m] PEX), or

W10267701RP (25 ft [7.62 m] PEX).

■ Install tubing only in areas where temperatures will

remain above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

■ Flat-blade screwdriver

■ 7/16" and 1/2" open-end wrenches or two adjustable

wrenches

■ 1/4" nut driver

Connect to Water Line

IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker off.

Style 1 (Recommended)

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

3. Use a quarter-turn shut-off valve or the equivalent, served by

a 1/2" copper household supply line.

NOTE:

To allow sufﬁcient water ﬂow to the refrigerator,

a minimum 1/2" size copper household supply line is

recommended.

A. Bulb

B. Nut

C. Copper tubing (to refrigerator)

D. Household supply line (1/2" minimum)

4. Now you are ready to connect the copper tubing to the

shut-off valve. Use 1/4" (6.35 mm) OD soft copper tubing to

connect the shut-off valve and the refrigerator.

■ Ensure that you have the proper length needed for the

job. Be sure both ends of the copper tubing are cut

square.

■ Slip compression sleeve and compression nut onto

copper tubing as shown. Insert end of tubing into outlet

end squarely as far as it will go. Screw compression

nut onto outlet end with adjustable wrench. Do not

overtighten.

B CA

A. Compression sleeve

B. Compression nut

C. Copper tubing

5. Place the free end of the tubing into a container or sink, and

turn on main water supply to ﬂush out tubing until water is

clear. Turn off shut-off valve on the water pipe.

NOTE: Always drain the water line before making the ﬁnal

connection to the inlet of the water valve to avoid possible

water valve malfunction.

6. Bend the copper tubing to meet the water line inlet, which

is located on the back of the refrigerator cabinet as shown.

Leave a coil of copper tubing to allow the refrigerator to be

pulled out of the cabinet or away from the wall for service.

Style 2

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

3. Locate a 1/2" (1.27 cm) to 1¼" (3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower rear corner of refrigerator

to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use

1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be

sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a 1/4" (6.35 mm) hole in the cold

water pipe you have selected.

DEF

A.Cold water pipe

B. Pipe clamp

C.Copper tubing

D.Compression nut

E.Compression sleeve

F. Shut-off valve

G. Packing nut

6. Fasten the shut-off valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4" (6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so the washer makes a watertight

seal. Do not overtighten, or you may crush the copper

tubing.

7. Slip the compression sleeve and compression nut on

the copper tubing as shown. Insert the end of the tubing

into the outlet end squarely as far as it will go. Screw the

compression nut onto outlet end with adjustable wrench.

Do not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn on the main water supply. Flush the tubing until water is

clear. Turn off the shut-off valve on the water pipe. Coil the

copper tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the

end of the water line inlet.

3. Thread the nut onto the end of the tubing. Tighten the nut by

hand. Then tighten it with a wrench two more turns. Do not

overtighten.

NOTE: To avoid rattling, be sure the copper tubing does

not touch the cabinet’s side wall or other parts inside the

cabinet.

A B C

A. Household water line

B. Nut (purchased)

C. Ferrule (purchased)

D. Refrigerator water tubing

4. Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

5. Turn shut-off valve on.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the plastic part that is attached to the

inlet of the water valve.

3. Attach the copper tube to the valve inlet using a

compression nut and sleeve as shown. Tighten the

compression nut. Do not overtighten.

4. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

5. Turn shut-off valve on.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

D. Compression nut

E. Valve inlet

7. On some models, the ice maker is equipped with a built-

in water strainer. If your water conditions require a second

water strainer, install it in the 1/4" (6.35 mm) water line at

either tube connection. Obtain a water strainer from your

nearest appliance dealer.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray

water tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not

long enough, a 1/4" x 1/4" (6.35 mm x 6.35 mm) coupling is

needed in order to connect the water tubing to an existing

household water line. Thread the provided nut onto the

coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a

wrench two more turns. Do not overtighten.

A B C D E F G

A. Refrigerator water tubing

B. Nut (provided)

C. Bulb

D. Coupling (purchased)

E. Ferrule (purchased)

F. Nut (purchased)

G. Household water line

4. Turn shut-off valve on.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Complete the Installation

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See “Water and Ice Dispensers” in

the User Instructions or User Guide.

NOTE: Allow 24 hours to produce the ﬁrst batch of ice. Allow

72 hours to completely ﬁll ice container.

REFRIGERATOR CARE

Cleaning

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, ﬂammable ﬂuids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and

a mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water.

4. There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is signiﬁcant pet trafﬁc

in the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efﬁciency.

If you need to clean the condenser:

■ Remove the base grille. See the “Door Removal”

instructions, either in the User Instructions or the

Installation Instructions and Owner’s Manual, or in the

separate instruction sheet provided with your refrigerator.

■ Use a vacuum cleaner with a soft brush to clean the

grille, the open areas behind the grille and the front

surface area of the condenser.

■ Replace the base grille when ﬁnished.

5. Plug in refrigerator or reconnect power.

Lights

NOTE: Not all bulbs will ﬁt your refrigerator. Be sure to replace

the bulb with one of the same size, shape and wattage.

■ The dispenser lights are LEDs that cannot be changed.

■ On some models, the interior lights are LEDs that cannot

be changed.

■ On s

ome models, the interior lights require a 40-watt

bulb

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable.

NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size,

shape and wattage.

4. Replace light shield when applicable.

5. Plug in refrigerator or reconnect power.

Vacation and Moving Care

Vacations

If You Choose to Leave Refrigerator On While You Are Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker and is

connected to the household water supply, turn off the water

supply to the refrigerator. Property damage can occur if the

water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker.

NOTE: Depending on your model, raise the wire shut-off arm

to OFF (up) position or press the switch to OFF (right).

4. Empty the ice bin.

If You Choose to Turn Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

■ Turn off the water supply to the ice maker at least one

day ahead of time.

■ When the last load of ice drops, raise the wire shut-off

arm to the OFF (up) position or move the switch to the

OFF (right) setting.

3. Unplug refrigerator.

4. Clean, wipe, and dry thoroughly.

5. Tape rubber or wood blocks to the tops of both doors to

prop them open far enough for air to get in. This stops odor

and mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

■ Turn off the water supply to the ice maker at least one

day ahead of time.

■ Disconnect the water line from the back of the

refrigerator.

■ When the last load of ice drops, raise the wire shut-off

arm to the OFF (up) position or move the switch to the

OFF (right) setting.

2. Remove all food from the refrigerator and pack all frozen

food in dry ice.

3. Empty the ice bin.

4. Unplug refrigerator.

5. Clean, wipe, and dry thoroughly.

6. Take out all removable parts, wrap them well, and tape them

together so they don’t shift and rattle during the move.

7. Depending on the model, raise the front of the refrigerator so

it rolls more easily or screw in the leveling legs so they don’t

scrape the ﬂoor. See “Adjust the Doors” or “Door Removal,

Leveling and Alignment.”

8. Tape the doors closed and tape the power cord to the back

of the refrigerator.

When you get to your new home, put everything back and refer

to the Installation Instructions for preparation instructions. Also,

if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

TROUBLESHOOTING

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

GENERAL OPERATION Possible Causes and/or Recommended Solutions

Refrigerator will not operate

■ Not connected to an electrical supply - Plug the power cord into a grounded 3 prong

outlet. Do not use an extension cord.

■ No power to the electrical outlet - Plug in a lamp to see if the outlet is working.

■ Household fuse has blown or circuit breaker has tripped - Replace the fuse or reset the

circuit breaker. If the problem continues, contact a licensed electrician.

■ New installation - Following installation, allow 24 hours for the refrigerator and freezer to

cool completely.

NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either

compartment (refrigerator or freezer) more quickly.

Motor seems to run too much

■ Your new refrigerator has an energy-efﬁcient motor - The refrigerator may run longer than

you’re used to, because the compressor and fans operate at lower speeds that are more

energy-efﬁcient. This is normal.

NOTE: Your refrigerator may run even longer if the room is warm, a large load of food is

added, the doors are opened often, or if a door has been left open.

Refrigerator seems noisy

The compressor in your new refrigerator regulates temperature more efﬁciently and uses less

energy than older models. During various stages of operation, you may hear normal operating

sounds that are unfamiliar.

The following noises are normal:

■ Buzzing/Clicking - Heard when the water valve opens and closes to dispense water or ﬁll

the ice maker. If the refrigerator is connected to a water line, this is normal. If the refrigerator

is not connected to a water line, turn off the ice maker.

■ Cracking/Crashing - Heard when ice is ejected from the ice maker mold.

■ Popping - Heard when the inside walls contract/expand, especially during initial cool down.

■ Pulsating/Whirring - Heard when the fans/compressor adjust to optimize performance

during normal operation.

■ Rattling - Heard when water passes through the water line, or due to the ﬂow of refrigerant.

Rattling may also come from items placed on top of the refrigerator.

■ Water running or gurgling - Heard when ice melts during the defrost cycle and water runs

into the drain pan.

■ Sizzling - Heard when water drips onto the heater during the defrost cycle.

GENERAL OPERATION Possible Causes and/or Recommended Solutions

Temperature is too warm

■ New installation - Following installation, allow 24 hours for the refrigerator and freezer to

cool completely.

NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either

compartment (refrigerator or freezer) more quickly.

■ Doors are opened often or not closed completely - This allows warm air to enter the

refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors

are properly sealed.

■ Air vents are blocked - Remove items that are immediately in front of the vents.

■ Large amount of warm food recently added - Allow several hours for the refrigerator to

return to its normal temperature.

■ Controls are not set correctly for the surrounding conditions - Adjust the controls to a

colder setting. Check the temperature again in 24 hours.

Temperature is too cold

■ Controls are not set correctly for the surrounding conditions - Adjust the controls to a

warmer setting. Check the temperature again in 24 hours.

■ Top refrigerator shelf is colder than lower shelves - On some models, air from the freezer

enters the refrigerator compartment through vents near the top refrigerator shelf. As a result,

the top shelf can be slightly colder than lower shelves.

■ Air vents are blocked - Remove items that are immediately in front of the vents.

Interior moisture buildup

NOTE: Some moisture buildup is normal. Clean with a soft dry cloth.

■ Room is humid - A humid environment contributes to moisture buildup. Use the refrigerator

only in an indoor location, with as little humidity as possible.

■ Doors are opened often or not closed completely - This allows humid air to enter the

refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors

are properly sealed.

Interior lights do not work

■ Doors have been open for an extended period of time - Close the doors to reset the lights.

■ Light bulb is loose in the socket or has burned out - On models with incandescent interior

light bulbs, tighten or replace the bulb. See the “Lights” section.

NOTE: On models with LED lights, call for assistance or service if the interior lights do not

illuminate when either door is opened. See the Warranty in the User Instructions or User Guide for

contact information.

Dispenser lights do not work

(on some models)

■ Dispenser light is turned off - On some models, if the dispenser light is set to OFF, the light

will turn on only when a dispenser pad/lever is pressed. If you want the dispenser light to

stay on continuously, select a different setting. See “Water and Ice Dispensers” in the User

Instructions or User Guide.

■ Dispenser light is set to AUTO or NIGHT LIGHT - On some models, if the dispenser light

is set to AUTO or NIGHT LIGHT, make sure the dispenser light sensor is not blocked. See

“Water and Ice Dispensers” in the User Instructions or User Guide.

NOTE: On models with LED lights, call for assistance or service if the dispenser lights do not

operate correctly. See the Warranty in the User Instructions or User Guide for contact information.

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

DOORS AND LEVELING Possible Causes and/or Recommended Solutions

Doors are difﬁcult to open

■ Gaskets are dirty or sticky - Clean the gaskets and contact surfaces with mild soap and

warm water. Rinse and dry with a soft cloth.

Doors will not close

completely

■ Door is blocked open - Move food packages away from the door. Make sure all bins and

shelves are in their correct positions. Make sure all packaging materials have been removed.

Doors appear to be uneven

■ Doors need to be aligned, or refrigerator needs to be leveled - See the leveling and door

alignment instructions.

Refrigerator rocks and

is not stable

■ Refrigerator is not level - To stabilize the refrigerator, remove the base grille and lower the

leveling feet until they touch the ﬂoor. See the leveling and door alignment instructions.

ICE AND WATER Possible Causes and/or Recommended Solutions

Ice maker is not producing

ice, not producing enough ice,

or producing small/hollow ice

■ Refrigerator is not connected to a water supply, or the water supply shut-off valve is not

fully turned on - Connect the refrigerator to a water supply and make sure the water shut-off

valve is fully open.

■ Kink in the water source line - A kink in the water line can reduce water ﬂow, resulting in

decreased ice production, small ice cubes, and/or hollow or irregularly-shaped ice. Straighten

the water line.

■ Ice maker is not turned on - Turn on the ice maker. See “Ice Maker and Storage Bin” in the

User Instructions or User Guide.

■ New installation - After connecting the refrigerator to a water source, ﬂush the water system.

(See “Water and Ice Dispensers” in the User Instructions or User Guide.) Wait 24 hours for

ice production to begin. Wait 72 hours for full ice production. Discard the ﬁrst three batches

of ice produced.

■ Large amount of ice was recently removed - Allow sufﬁcient time for the ice maker to

produce more ice.

■ Ice is jammed in the ice maker ejector arm - Remove ice from the ejector arm using a

plastic utensil.

■ Inadequate water pressure - Verify that the household has adequate water pressure. See

the “Water Supply Requirements” section.

■ Water ﬁlter is installed incorrectly - Make sure the ﬁlter is properly installed. See “Water

Filtration System” in the User Instructions or User Guide.

■ A reverse osmosis water ﬁltration system is connected to your cold water supply - This

can decrease water pressure. See the “Water Supply Requirements” section.

NOTE: If questions remain regarding water pressure, contact a licensed, qualiﬁed plumber.

ICE AND WATER Possible Causes and/or Recommended Solutions

Ice dispenser will not operate

properly

■ Doors not closed completely - Make sure both doors are ﬁrmly closed. (On some models,

only the freezer door must be closed in order to operate the dispenser.)

■ New installation - After connecting the refrigerator to a water source, ﬂush the water system.

(See “Water and Ice Dispensers” in the User Instructions or User Guide.) Wait 24 hours for ice

production to begin. Wait 72 hours for full ice production. Discard the ﬁrst three batches of

ice produced.

■ Ice maker is not turned on, or ice bin is not installed correctly - Turn on the ice maker

and make sure the ice storage bin is ﬁrmly in position. See “Ice Maker and Storage Bin” in the

User Instructions or User Guide.

■ Ice is clogged or frozen together in the ice storage bin, or ice is blocking the ice

delivery chute - Remove or separate the clogged ice, using a plastic utensil if necessary.

Clean the ice delivery chute and the bottom of the ice storage bin using a warm damp cloth,

then dry both thoroughly. To avoid clogging and to maintain a fresh supply of ice, empty the

storage bin and clean both the storage bin and the delivery chute every 2 weeks.

■ Wrong ice has been added to the storage bin - Use only ice cubes produced by the current

ice maker.

■ Dispenser is locked - Unlock the dispenser. See “Water and Ice Dispensers” in the User

Instructions or User Guide.

■ Ice dispenser jams while dispensing crushed ice - For models with the ice storage bin on

the door, temporarily switch from crushed ice to cubed ice to clear the jam.

■ Dispenser pad/lever has been pressed too long - Ice will automatically stop dispensing.

Wait a few minutes for the dispenser to reset, then resume dispensing. Take large amounts of

ice directly from the ice bin, not through the dispenser.

■ Water pressure to the home is not at or above 30 psi (207 kPa) - The water pressure to

the home affects the ﬂow from the dispenser. See the “Water Supply Requirements” section.

■ Water ﬁlter is clogged or incorrectly installed - Replace ﬁlter or reinstall it correctly. See

“Water Filtration System” in the User Instructions or User Guide.

Ice or water has an off-taste,

odor, or gray color

■ New plumbing connections - New plumbing connections can result in off-ﬂavored or

discolored ice or water. This problem should go away over time.

■ Ice has been stored too long - Discard the ice and wash the ice bin. Allow 24 hours for the

ice maker to produce new ice.

■ Odor has transferred from food - Use airtight moisture-proof packaging to store food.

■ Use of non-recommended water supply line - Odors and tastes can transfer from certain

materials used in non-recommended water supply lines. Use only a recommended water

supply line. See the “Water Supply Requirements” section.

■ There are minerals (such as sulfur) in the water - A water ﬁlter may need to be installed in

order to remove the minerals.

■ Water ﬁlter was recently installed or replaced - Gray or dark discoloration in ice or water

indicates that the water ﬁltration system needs additional ﬂushing. See “Water and Ice

Dispensers” in the User Instructions or User Guide.

Water dispenser will not

operate properly

■ Doors not closed completely - Make sure both doors are ﬁrmly closed. (On some models,

only the freezer door must be closed in order to operate the dispenser.)

■ Refrigerator is not connected to a water supply, or the water supply shut-off valve is not

turned on - Connect the refrigerator to a water supply and make sure the water shut-off valve

is fully open.

■ Kink in the water source line - A kink in the water line can reduce water ﬂow to the

dispenser. Straighten the water line.

■ Water pressure to the home is not at or above 30 psi (207 kPa) - The water pressure to

the home affects the ﬂow from the dispenser. See the “Water Supply Requirements” section.

■ New installation - After connecting the refrigerator to a water source, ﬂush the water system.

See “Water and Ice Dispensers” in the User Instructions or User Guide.

■ Dispenser is locked - Unlock the dispenser. See “Water and Ice Dispensers” in the User

Instructions or User Guide.

■ Water ﬁlter is clogged or incorrectly installed - Replace ﬁlter or reinstall it correctly. See

“Water Filtration System” in the User Instructions or User Guide.

■ A reverse osmosis water ﬁltration system is connected to your cold water supply - This

can decrease water pressure. See the “Water Supply Requirements” section.

NOTE: If questions remain regarding water pressure, contact a licensed, qualiﬁed plumber.

ICE AND WATER Possible Causes and/or Recommended Solutions

Water is leaking or dripping

from the dispenser

NOTE: After dispensing, a few additional drops of water are normal.

■ Glass was not held under the dispenser long enough - Hold the glass under the dispenser

for 2 to 3 seconds after releasing the dispenser pad/lever.

■ New installation, or water ﬁlter was recently installed or replaced - Air in the water lines

causes the water dispenser to drip. Flush the water system to remove the air in the water

lines. See “Water and Ice Dispensers” in the User Instructions or User Guide.

■ Residual ice in the dispenser chute is melting - Make sure the ice chute is free of ice

shavings or pieces.

Water is leaking from the back

of the refrigerator

■ Water line connections are not fully tightened - Make sure all connections are ﬁrmly

tightened. See the “Connect Water Supply” section.

Water from the dispenser is

not cool enough (on some

models)

NOTE: Water from the dispenser is chilled to 50°F (10°C).

■ New installation - Allow 24 hours after installation for the water supply to cool completely.

■ Recently dispensed a large amount of water - Allow 24 hours for the new water supply to

cool completely.

■ Water has not been recently dispensed - The ﬁrst glass of water may not be cool. Discard

the ﬁrst glass of water dispensed.

■ Refrigerator is not connected to a cold water pipe - Make sure the refrigerator is

connected to a cold water pipe. See the “Water Supply Requirements” section.

PERFORMANCE DATA SHEET

Water Filtration System

Model P5WB2L/P4RFWB Capacity 200 Gallons (757 Liters)

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below.

The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to

the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa).

Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).

■

It is important that operational, maintenance, and filter

replacement requirements be carried out for the product to

perform as advertised. Property damage can occur if all

instructions are not followed.

Use replacement filter according you filtration system, see

“Ice and Water” in the User Guide

Water Filter:

Water Filtration System Style 1 - Order Part # EDR1RXD1

Water Filtration System Style 2 - Order Part # EDR2RXD1

When the water filter status changes from TURN OFF to RED

light on your control panel, it is recommended that you

replace the filter.

■

After changing the water filter, flush the water system. See

“Water and Ice Dispensers” or “Water Dispenser” in the User

Instructions or User Guide.

■ These contaminants are not necessarily in your water supply.

While testing was performed under standard laboratory

conditions, actual performance may vary.

■ The product is for cold water use only.

■ The water system must be installed in compliance with state

and local laws and regulations.

■ Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

■ Refer to the “Warranty” section (in the User Instructions or

User Guide) for the Manufacturer’s name, address and

telephone number.

■ Refer to the “Warranty” section (in the User Instructions or

User Guide) for the Manufacturer’s limited warranty.

Application Guidelines/Water Supply Parameters

System tested and certified by NSF International against NSF/ANSI

Standard 42 for the reduction of Chlorine Taste and Odor, and Particulate

Class I*; and against NSF/ANSI Standard 53 for the reduction of Live

Cysts, Asbestos, Lead, Lindane, Toxaphene, Atrazine, and 2,4 - D.

Substance Reduction

Aesthetic Effects

NSF Reduction

Requirements

Average

Influent

Influent Challenge

Concentration

Maximum

Effluent

Minimum %

Reduction

Average %

Reduction

Chlorine Taste/Odor

Particulate Class I

50% reduction

85% reduction

2.0 mg/L

7,300,000 #/mL

2.0 mg/L ± 10%

At least 10,000 particles/mL

0.20 mg/L

75,000 #/mL

97.2

99.4

Contaminant

Reduction

NSF Reduction

Requirements

Average

Influent

Influent Challenge

Concentration

Maximum

Effluent

Minimum %

Reduction

Average %

Reduction

Live Cysts

†

99.95% 160,000/L 50,000/L min. 54/L

†

99.97 99.99

Asbestos 99% 87 MFL 10

to 10

fibers/L

††

0.17 MFL 99 99

Lead: @ pH 6.5

Lead: @ pH 8.5

0.010 mg/L

0.160 mg/L

0.140 mg/L

0.15 mg/L ± 10%

0.001 mg/L

0.005 mg/L

99.4

98.6

99.4

98.6

Lindane 0.0002 mg/L 0.0019 mg/L 0.002 mg/L ± 10% 0.00002 mg/L 98.9 99

Toxaphene 0.003 mg/L 0.014 mg/L 0.015 mg/L ± 10% 0.001 mg/L 93 93

Atrazine 0.003 mg/L 0.0094 mg/L 0.009 mg/L ± 10% 0.0005 mg/L 94.5 94.7

2,4 - D 0.07 mg/L 0.220 mg/L 0.210 mg/L ± 10% 0.028 mg/L 87.5 96.1

Water Supply

Water Pressure

Water Temperature

Service Flow Rate

City or Well

30 - 120 psi (207 - 827 kPa)

33° - 100°F (0.6° - 37.8°C)

0.5 gpm (1.9 Lpm) @ 60 psi

†

††

Class I particle size: >0.5 to <1 um

Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

Based on the use of Cryptosporidium parvum oocysts

Fibers greater than 10 um in length

® NSF is a registered trademark of NSF International.

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

SÉCURITÉ DU RÉFRIGÉRATEUR

AVERTISSEMENT :

réfrigérateur, prendre quelques précautions fondamentales, y compris les suivantes :

Pour réduire les risques d'incendie, de choc électrique ou des blessures lors de l'utilisation du

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ

CONSERVEZ CES INSTRUCTIONS

■ Brancher l'appareil sur une prise à 3 alvéoles reliée à la terre.

■ Ne pas enlever la broche de liaison à la terre.

■ Ne pas utiliser un adaptateur.

■ Ne pas utiliser un câble de rallonge.

■ Débrancher la source de courant électrique avant l'entretien.

■ Replacer pièces et panneaux avant de faire la remise en marche.

■ Enlever les portes de votre vieux réfrigérateur.

■ Raccorder à la canalisation d'arrivée d'eau potable uniquement.

■ Utiliser un produit de nettoyage ininflammable.

■ Garder les matériaux et les vapeurs inflammables, telle que

l'essence, loin du réfrigérateur.

■ Utiliser deux ou plus de personnes pour déplacer et installer le

réfrigérateur.

■ Débrancher le réfrigérateur avant l'installation de la

machine à glaçons (seulement pour modèles prêts à

recevoir une machine à glaçons).

■ Utiliser un verre robuste pour prendre des glaçons (sur

certains modèles).

■ Ne pas heurter les portes en verre du réfrigérateur (sur

certains modèles).

■ Cet appareil ne convient pas à une utilisation par des

personnes (y compris des enfants) à capacités

physiques, sensorielles ou mentales réduites, ou

possédant un manque d'expérience et de

connaissances, à moins qu'elles ne soient placées sous

supervision ou qu'elles aient reçu des instructions

concernant l’utilisation de l'appareil par une personne

responsable de leur sécurité.

■ Les enfants doivent être placés sous surveillance afin de

s'assurer qu'ils ne jouent pas avec l'appareil.

Avertissements de la proposition 65 de l'État de Californie :

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par l’État de Californie pour être à l’origine de

cancers.

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par l’État de Californie pour être à l’origine de

malformations et autres déficiences de naissance.

INSTRUCTIONS D’INSTALLATION

ET MANUEL D’UTILISATION

Réfrigérateur côte à côte

Mise au rebut appropriée

de votre vieux réfrigérateur

AVERTISSEMENT

Risque de suffoquer

Enlever les portes de votre vieux réfrigérateur.

Le non-respect de cette instruction peut causer

un décès ou des lésions cérébrales.

IMPORTANT: L’emprisonnement et l’étouffement des enfants

ne sont pas un problème du passé. Les réfrigérateurs jetés ou

abandonnés sont encore dangereux, même s’ils sont laissés

abandonnés pendant “quelques jours seulement”. Si vous

vous débarrassez de votre vieux réfrigérateur, veuillez suivre les

instructions suivantes pour aider à éviter les accidents.

Avant de jeter votre vieux réfrigérateur ou congélateur :

■ Enlever les portes.

■ Laisser les tablettes en place de sorte que les enfants ne

puissent pas y pénétrer facilement.

Renseignements importants à propos de la mise au

rebut des fluides réfrigérants :

Mettre le réfrigérateur au rebut conformément à la

réglementation fédérale et locale. Les fluides réfrigérants

doivent être évacués par un technicien certifié et agréé par

l’EPA conformément aux procédures établies.

INSTRUCTIONS D’INSTALLATION

Déballage du réfrigérateur

AVERTISSEMENT

Risque du poids excessif

Utiliser deux ou plus de personnes pour déplacer et

installer le réfrigérateur.

Le non-respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

Importants renseignements à savoir au sujet des tablettes

et des couvercles en verre :

Ne pas nettoyer les tablettes ou couvercles en verre avec de

l’eau tiède quand ils sont froids. Les tablettes et les

couvercles peuvent se briser s'ils sont exposés à des

changements soudains de température ou à un impact tel

que coup brusque. Le verre trempé est conçu pour éclater

en d’innombrables pièces minuscules. Ceci est normal. Les

tablettes et les couvercles en verre sont lourds. Les saisir à

deux mains lors de leur dépose afin d'éviter de les faire

tomber.

Déplacement de votre réfrigérateur :

Votre réfrigérateur est lourd. Lors du déplacement de votre

réfrigérateur pour le nettoyage ou un entretien ou réparation,

veiller à recouvrir le plancher avec du carton ou un panneau

de fibres dures pour éviter qu'il ne subisse tout dommage.

Toujours tirer le réfrigérateur tout droit lors de son

déplacement. Ne pas incliner le réfrigérateur d’un côté ou de

l’autre ni le “faire marcher” en essayant de le déplacer car le

plancher pourrait être endommagé.

Retirer les matériaux d’emballage. Ne pas utiliser d’instruments

coupants, d’alcool à friction, de liquides inﬂammables ou de

nettoyants abrasifs pour enlever le ruban adhésif ou la colle. Ces

produits peuvent endommager la surface de votre réfrigérateur.

Pour plus de renseignements, voir “Sécurité du réfrigérateur”.

†®TORX et T30 sont des marques déposées de Acument Intellectual Properties, LLC.

Retrait, réglage de l’aplomb et alignement des portes

Rassembler les outils et pièces nécessaires et lire toutes les instructions avant de commencer l’installation. Conserver ces instructions

pour référence ultérieure.

REMARQUE :

En cas de déménagement, prendre les mesures de l’entrée de l’habitation, avant de déplacer l’appareil, aﬁn de

déterminer s’il est nécessaire de démonter la porte du réfrigérateur et celle du congélateur. Si les portes doivent être retirées, voir les

instructions ci-dessous.

IMPORTANT : Avant de commencer, débrancher le réfrigérateur ou déconnecter la source de courant électrique. Retirer les aliments,

le bac d’entreposage des glaçons (sur certains modèles) et tout balconnet réglable ou compartiment utilitaire des portes.

OUTILS NÉCESSAIRES : Niveau à bulle; tournevis à lame plate; clé de 5/16" et 11/16"; clés à douille à tête hexagonale de 1/4", 3/8"

et 5/16", tournevis TORX

T30

®†

AVERTISSEMENT

Risque de choc électrique

Déconnecter la source de courant électrique avant d'enlever les portes.

Le non-respect de cette instruction peut causer un décès ou un choc électrique.

Ne pas retirer les vis A.

A CB

A. Fiches de câblage

B. Agrafe de câblage

C. Œillets

A. Avant du raccord

Tirer vers soi.

Relever

Abaisser

Clé de

5/16"

Serrer

Clé de

11/16"

Relever

Abaisser

Relever

Ne pas retirer les vis B.

Réfrigérateur complet

Charnières inférieures gauche

et droite

Retrait des portes

Câblage

Tuyau du distributeur

d’eau

Grille de la base

Porte du ﬁltre à eau et grille

de la base

Vis d’alignement

Écrou de blocage

Vis de réglage de l’aplomb

Ne pas retirer les vis A.

Charnière supérieure

droite

Caisse

Porte du

congélateur

Grille de

la base

Porte du

réfrigérateur

Roulettes avant réglables

Charnière supérieure

gauche

Porte du

ﬁltre à eau

A. Tirer vers la droite pour l’extraire.

B. Tourner et faire passer sous la porte.

Desserrer

La page charge ...

Whirlpool WRS312SNHW Mode d'emploi

Marque: Whirlpool

Modèle: WRS312SNHW

Catégorie: Frigos

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WRS312SNHW Operating instructions

Whirlpool WRS312SNHW Mode d'emploi

Whirlpool WRS312SNHW Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents