Simplicity 040589-00 Guide d'installation

Marque: Simplicity

Modèle: 040589-00

Catégorie: Groupes électrogènes

Taper: Guide d'installation

Ce manuel convient également à

80081732

Revision C

Not for

Reproduction

Table of Contents:

California Proposition 65..................................................... 3

Thank You..............................................................................3

Where to Find Us..................................................................3

For Future Reference........................................................... 3

Important Safety Instructions..............................................3

Safety Alert Symbol and Signal Words............................ 3

Safety Symbols and Meanings.........................................3

Safety Messages.............................................................. 4

FCC Part 15 Information To User.................................... 7

General Information..............................................................8

Equipment Description..................................................... 8

Installer Responsibilities...................................................8

Owner Responsibilities.....................................................8

Installation Factors to Consider........................................8

Delivery Inspection........................................................... 8

Shipment Contents........................................................... 8

Generator Placement............................................................9

Generator Location Considerations..................................9

Reduce the Risk of Carbon Monoxide Poisoning.............9

Reduce The Risk of Fire................................................ 11

Other General Location Guidelines................................13

Installation........................................................................... 14

Lifting the Generator...................................................... 14

Cold Weather Kit............................................................ 14

Anchoring and Wind Rating........................................... 14

Electrical and Fuel Inlet Locations................................. 15

Access Panels................................................................ 15

Fuel Installation Plan......................................................16

Electrical Field Connections........................................... 20

Final Installation Considerations.................................... 22

System Control Board.................................................... 23

Initial Start-Up (No Load)............................................... 24

Operation............................................................................. 26

Features and Controls - 17kW and 20kW

Generators......................................................................26

Important Owner's Considerations................................. 28

Automatic Operation Sequence..................................... 28

Setting the Exercise Timer.............................................28

Maintenance.........................................................................30

Servicing the System..................................................... 30

Maintenance Schedule...................................................30

Generator Maintenance..................................................30

Cleaning the Generator..................................................30

Engine Maintenance.......................................................31

Changing Engine Oil and Oil Filter.................................31

Adjust Valve Lash.......................................................... 32

Electronic Governor System...........................................33

Electronic Governing Check...........................................33

Service the Spark Plugs.................................................34

Engine Air Cleaner......................................................... 34

Exhaust System Maintenance........................................35

Fuel System Maintenance..............................................35

Mixer/Throttle Control Device.........................................35

Alarms (Service Code Detection System)......................35

Acknowledge and Reset the Alarms (Service Code

Detection System).......................................................... 35

Electrical System Maintenance...................................... 36

Troubleshooting..................................................................38

Troubleshooting.............................................................. 38

Diagrams and Schematics................................................. 40

Wiring Diagram and Schematic......................................40

Specifications......................................................................41

Generator Specifications: 17kW and 20KW...................41

Engine Specifications..................................................... 41

Not for

Reproduction

California Proposition 65

WARNING

This product can expose you to chemicals including used

engine oil, which is known to the State of California to

cause cancer, and carbon monoxide, which is known

to the State of California to cause birth defects or

other reproductive harm. For more information go

towww.P65Warnings.ca.gov.

Thank You

Thank you for purchasing this quality-built Briggs & Stratton®

generator. We are pleased that you have placed your

confidence in the Briggs & Stratton brand. When operated

and maintained according to the instructions in this manual,

your generator will provide many years of dependable

service.

This manual contains safety information to make you aware

of the hazards and risks associated with standby generators

and how to avoid them. This product is only for use as an

optional generator system which provides an alternate

source of electric power and to serve loads such as heating,

refrigeration systems, and communication systems that, when

stopped during any power outage, could cause discomfort or

inconvenience.

SAVE THESE INSTRUCTIONS -This manual contains

important instructions that must be obeyed during installation,

operation, and maintenance of the generator and batteries.

This generator system requires professional installation

before use.The installermust obeythe instructions

completely.

Where to Find Us

You never have to look far to find support and service for

your equipment. There are many authorized service dealers

worldwide that provide quality service. You can also contact

Customer Service by phone at800-732-2989between 8:00

AM and 5:00 PM central time or click on Dealer Locator

at www.briggsandstratton.com, which provides a list of

authorized dealers.

For Future Reference

Please fill out the information below and keep with your

receipt. Have this information at hand if it becomes necessary

to contact your installer or authorized dealer regarding service

or repair of the unit.

Date of Purchase: ________________________________

Dealer / Retailer: _________________________________

Dealer's / Retailer'sPhone Number: __________________

GENERATOR:

Model Number: ____________________________

Model Revision: ____________________________

Serial Number: ____________________________

ENGINE:

Model Number: __________________________________

Serial Number: ___________________________________

Important Safety Instructions

Every effort has been made to make sure that the information

in this manual is accurate and current. However, we reserve

the right to change, or improve the product and this document

without notification.

The manufacturer cannot possibly anticipate every possible

circumstance that can involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not recommend, you must satisfy yourself that it is safe for

you and others. You must also make sure that the procedure,

work method or operating technique that you choose does not

render the equipment unsafe.

Safety Alert Symbol and Signal Words

The safety alert symbol identifies safety information

about hazards that can result in personal injury. A signal

word (DANGER,WARNING, orCAUTION) is used with

the alert symbol to indicate the likelihood and the potential

severity of injury. In addition, a hazard symbol may be used

to represent the type of hazard.

DANGERindicates a hazard which, if not

avoided,willresult in death or serious injury.

WARNINGindicates a hazard which, if not

avoided,couldresult in death or serious injury.

CAUTIONindicates a hazard which, if not

avoided,couldresult in minor or moderate injury.

NOTICEIndicates information considered important but not

hazard-related.

Safety Symbols and Meanings

Symbol Meaning

Safety alert symbol. Indicates a potential personal injury

hazard.

Not for

Reproduction

Symbol Meaning

Read Manual. Failure to obey warnings, instructions,

installation manual, and operator’s manual could result in

death or serious injury.

Fire

Explosion

Electric Shock

Toxic Fumes

Moving Parts

Wear Eye Protection

Hazardous Chemical

Hot Surface

Rotating Parts

Crush and Cut

Explosive Pressure

Symbol Meaning

Auto Start

Safety Messages

WARNING

Failure to read and obey the operator’s manual, all

warnings, and operating instructions could result in death or

serious injury.

WARNING



Engine exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes. You cannot

smell it, see it, or taste it. Even if you do not smell exhaust

fumes, you could still be exposed to carbon monoxide gas.

• Operate this product ONLY outdoors in an area that will

not accumulate deadly exhaust gas.

• Direct exhaust gas away from any windows, doors,

ventilation intakes, soffit vents, crawl spaces, open

garage doors or other openings that can allow exhaust

gas to enter inside or be drawn into a potentially

occupied building or structure.

• Carbon monoxide detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/recommendations. Smoke alarms cannot

detect carbon monoxide gas.

• If you start to feel sick, dizzy, weak, or your carbon

monoxide alarm sounds while using this product, get to

fresh air right away. Call emergency services. You may

have carbon monoxide poisoning.



WARNING

Storage batteries give off explosive hydrogen gas

during recharging. Slightest spark could ignite hydrogen

and cause explosion, resulting in death or serious injury.

• DO NOT dispose of battery in a fire. Recycle battery.

• DO NOT allow any open flame, spark, heat, or lit

cigarette during and for several minutes after charging a

battery.



Not for

Reproduction

WARNING

Battery electrolyte fluid contains acid and is extremely

caustic. Contact with battery contents could cause severe

chemical burns.

• DO NOT open or mutilate the battery

• Wear protective goggles, rubber apron, rubber boots

and rubber gloves.

• Immediately wash electrolyte from skin with water.

• If electrolyte contacts eyes, immediately flush with

water and seek medical attention.

• Spilled electrolyte is to be washed down with an acid

neutralizing agent.



WARNING

A battery presents a risk of high short circuit current.

• Remove watches, rings, or other metal objects.

• Use tools having insulated handles.

• Disconnect charging source prior to connecting or

disconnecting battery terminals.

• Do not lay tools or metal parts on top of batteries.

• Disconnect the negative (-) cable at the battery during

installation and maintenance.



WARNING

Failure to isolate generator from utility power could

result in death or serious injury to electric utility workers due

to backfeed of electrical energy.

• Use a listed transfer switch to connect to a building

electrical system.

WARNING

Generator and utility voltage could cause electrical

shock or burn resulting in death or serious injury.

• Installation must be performed by a licensed

professional.

• Disconnect all sources of electricity before installing or

servicing equipment.

• Ground system before applying power.

WARNING

Hazardous Voltage -Installing low and high voltage

wire in same conduit could cause electric shock or burns,

resulting in death or serious injury.

• Do not run low and high voltage wire in the same

conduit unless the insulation rating on ALL wiring is

rated for 600V. See NFPA 70 for more information.

WARNING

Exhaust heat/gases could ignite combustibles or

structures resulting in death or serious injury.

• Exhaust outlet of enclosure must have at least 5 ft.

(1.5m) minimum clearance from any structure, shrubs,

trees, or any kind of vegetation.

• Enclosure must be at least 5 ft (1.5m) from windows,

doors, any wall opening, shrubs, or vegetation over 12

inches (30.5 cm) in height.

• Enclosure must have a minimum of 5 ft. (1.5 m)

overhead clearance from any structure, overhang, or

trees.

• DO NOT place enclosure under a deck or other type of

structure that may confine airflow.

• Smoke detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions.

Carbon monoxide alarms cannot detect smoke.

• Do not place enclosure in a manner other than shown in

illustrations.

WARNING

Exhaust heat/gases could ignite combustibles

causing a fire, resulting in death or serious injury.

• Remove all combustible materials from in and around

the generator compartment.

WARNING

 Gaseous vapors are extremely flammable and

explosive. Fire or explosion can cause severe burns or

death.

• Never start and run the engine with the air cleaner

assembly (if equipped) or the air filter (if equipped)

removed.

Not for

Reproduction

WARNING

With the battery connected, the generator may crank

and start without warning resulting in death or serious injury.

• Do not connect the negative (-) cable at the battery until

the installation is complete.

WARNING

With the battery connected, the generator may crank

and start without warning resulting in death or serious injury.

• Before servicing, stop the generator and disconnect the

negative (-) cable at the battery.

WARNING

Hazardous Voltage - Contact with power lines could

cause electric shock or burns, resulting in death or serious

injury.

• If lifting or hoisting equipment is used, DO NOT contact

any power lines.

• DO NOT lift or move generator without assistance.

WARNING

Propane and Natural Gas are extremely flammable

and explosive, which could cause burns, fire or explosion

resulting in death or serious injury.

• Installation must be performed by a licensed

professional.

• Install the fuel supply system according to NFPA 37 and

other applicable fuel-gas codes.

• Before placing the generator into service, the fuel

system lines must be properly purged and leak tested.

• NO leakage is permitted.

• DO NOT operate engine if smell of fuel is present.

WARNING

Propane and Natural Gas are extremely flammable

and explosive, which could cause burns, fire or explosion

resulting in death or serious injury.

• The generator is equipped with an automatic safety

gasfuel shut-off valve.

• DO NOT operate the equipment if the fuel shut-off valve

is missing or inoperative.

WARNING

Propane and Natural Gas are extremely flammable

and explosive, which could cause burns, fire or explosion

resulting in death or serious injury.

• LP gas is heavier than air and will settle in low areas.

• Natural gas is lighter than air and will collect in high

areas.

• The slightest spark could ignite these fuels and cause

an explosion.

• DO NOT light a cigarette or smoke.

WARNING

Propane and Natural Gas are extremely flammable

and explosive, which could cause burns, fire or explosion

resulting in death or serious injury.

• Inspect the fuel system periodically.

• NO leakage is permitted.

• DO NOT operate engine if smell of fuel is present.

WARNING

Generatorand utilityvoltage could cause electrical

shock or burn resulting in death or serious injury.

• DO NOT allow unqualified persons to operate or

servicethis equipment.

WARNING

Unintentional sparking could cause fire or electric shock

resulting in death or serious injury.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.



Not for

Reproduction

NOTICE Improper treatment of generator could damage it

and shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, contact your

authorized dealer.

• Operate generator only on level surfaces.

• Adequate, unobstructed flow of cooling and ventilating

air is critical to correct generator operation.

• The access panels/doors must be installed whenever

the unit is running.

• DO NOT expose generator to excessive moisture, dust,

dirt, or corrosive vapors.

• Remain alert at all times while working on this

equipment. Never work on the equipment when you are

physically or mentally fatigued.

• DO NOT insert any objects through cooling slots.

• DO NOT use the generator or any of its parts as a

step. Stepping on the unit could cause stress and

break parts. This may result in dangerous operating

conditions from leaking exhaust gases, fuel leakage, oil

leakage, etc.

• Shut off generator if:

• electrical output is lost.

• equipment sparks, smokes, or emits flames.

• unit vibrates excessively or makes unusual noises.

FCC Part 15 Information To User

Pursuant to part 15.21 of the FCC Rules, you are cautioned

that changes or modifications to the product not expressly

approved by Briggs & Strattoncould void your authority to

operate the product.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this

device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

Not for

Reproduction

General Information

For most applications, this manual contains the information

necessary for the correct installation, operation, and

maintenance of the equipment. All efforts have been made to

make sure that the information in this manual is accurate and

current. We reserve the right to change the product and this

document without notification.

Equipment Description

NOTICE This product does NOT qualify for either an

emergency standby or legally required standby system as

defined by NFPA 70 (NEC).

• Emergency generator systems are intended to

automatically supply illumination, power, or both, to

designated areas and equipment in the event of failure

of the normal supply. Emergency systems can also

provide power for such functions as ventilation where

essential to maintain life, where current interruption of the

normal supply would produce serious life safety or health

hazards.

• Legally Required standby generator systems are

intended to automatically supply power to selected

loads in the event of failure of the normal source which

can create hazards or hamper rescue or fire-fighting

operations.

Installer Responsibilities

• Read and obey the safety instructions.

• Install only aNRTL-approved transfer switch that is

compatible with the generator.

• Read and obey the instructions in this Installation and

Operation Manual.

• Installation must strictly comply with all applicable codes,

industry standards, laws, and regulations.

• Allow sufficient room on all sides of the generator for

maintenance and service.

• Discuss the generator placement with owner.

• Make sure that ALL manualsare given to the owner after

the installation has been completed.

Owner Responsibilities

• Read and obey the instructions in this Installation and

Operation Manual.

• Follow a regular schedule for maintaining and using the

generator, as specified in this manual.

• Carbon monoxide detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions and recommendations. Smoke alarms cannot

detect carbon monoxide gas.

• Smoke detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions and

recommendations. Carbon monoxide alarms cannot

detect smoke.

Installation Factors to Consider

The illustrations shown in this manual are for typical

circumstances. They are meant to familiarize you with the

installation options available for the generator.

Federal and local codes, appearance, noise levels, fuel types,

and distances are installation factors that must be considered.

Remember that, as the distance increases from the existing

electrical service and gaseous fuel supply, and the number

of bends in the fuel supply increases, compensations must

be made for piping and wiring materials. This is necessary

to comply with local codes and overcome electrical voltage

drops and gaseous fuel pressure drops.

Delivery Inspection

Avoid damage from dropping, bumping, or collision with the

shipping carton.

After removing the carton, carefully inspect the generator for

any damage that may have occurred during shipment.

If loss or damage is found at the time of delivery, have the

person(s) making the delivery notate the loss or damage on

the freight bill and affix his signature under the consignor’s

memo of loss or damage. If the loss or damage is notated

after delivery, separate the damaged materials and then

contact the carrier for claim procedures. Missing or damaged

parts are notwarranted.

Shipment Contents

The generator system is supplied with:

• Oil (5W30 Synthetic)

• Flexible fuel line

• Quick Operation Manual

• Product and emissions warranty booklet

• Two access keys

• Two 15 Amp ATO-type fuses

• Four lifting hole caps

• Touch up paint

Not included (You will need):

• Carbon monoxide detector(s)

• Smoke detector(s)

• Starting battery

• Connecting wire and conduit

• Fuel supply valves/plumbing

• Crane, lifting straps, chains or cables

• Two 60” (152cm) lengths of 3/4” (1.9cm) nominal

minimum Schedule 40 steel pipe (NOT conduit)

• Torque screwdriver, 5 to 50 inch-pound range

• Multi-meter

Not for

Reproduction

Generator Placement

Before installing the generator, consult with the owner

and convey the following requirements, which must be

satisfied before the installation is complete. There are two

equally important safety concerns in regards to carbon

monoxide poisoning and fire. There are also several general

location guidelines that must be met before the installation is

considered complete.

WARNING



Engine exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes. You cannot

smell it, see it, or taste it. Even if you do not smell exhaust

fumes, you could still be exposed to carbon monoxide gas.

• Operate this product ONLY outdoors in an area that will

not accumulate deadly exhaust gas.

• Direct exhaust gas away from any windows, doors,

ventilation intakes, soffit vents, crawl spaces, open

garage doors or other openings that can allow exhaust

gas to enter inside or be drawn into a potentially

occupied building or structure.

• Carbon monoxide detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/recommendations. Smoke alarms cannot

detect carbon monoxide gas.

• If you start to feel sick, dizzy, weak, or your carbon

monoxide alarm sounds while using this product, get to

fresh air right away. Call emergency services. You may

have carbon monoxide poisoning.



• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors and

windows for ventilation. Carbon monoxide can quickly

build up in these spaces and can linger for hours, even

after this product has shut off.

• ALWAYS place this product downwind and point the

engine exhaust (A) away from occupied spaces.

 (A) Exhaust outlet side of enclosure.

 (B)Air inlet side of enclosure.

Generator Location Considerations

The installation location of the generator has a direct effect

on:

1. The amount and size of the plumbing required to fuel the

generator.

2. The amount and size of the wiring required to control and

connect the generator.

3. The safety of the installation regarding exhaust gas and

carbon monoxide hazards, fire risks, proximity to other

utilities, and exposure to weather elements.

Specific location guidelines are discussed in the next

section. The owner and installer must consult one another

to determine how the site can affect installation costs and

compliance with local codes andstandards.

There are two critical safety concerns to be addressed -

carbon monoxide poisoning and the risk of fire, as follows:

Reduce the Risk of Carbon Monoxide Poisoning

The arrows in the figure below point to potential points of entry for Carbon Monoxide Gas.



Not for

Reproduction

All fossil fuel burning equipment, such as standby generators (A), contains carbon monoxide (CO) gas in the engine exhaust

(H). CO gas is odorless, colorless and tasteless and is unlikely to be noticed until a person is overcome. CO gas can kill you

so it is required that the following is included as part of the installation.

• Install generator (A) outdoors in an area that will not accumulate deadly exhaust gas (H).

• DO NOT install the generator (A) where exhaust gas (H) can accumulate and enter inside or be drawn into a potentially

occupied building or structure.

• In many states it is required by law to have a Carbon Monoxide (CO) detector that works in your home. Carbon monoxide

detector(s) MUST be installed and maintained indoors according to the manufacturer’s instructions / recommendations. A

CO detector is an electronic device that detects hazardous levels of CO. When there is a buildup of CO, the detector will

alert the occupants with an alarm and by flashing a visual indicator light. Smoke alarms cannot detect CO gas.

• Your neighbor(s) home can be exposed to the engine exhaust (H) from your standby generator (A) and must be

considered when installing your standby generator.

• Make sure exhaust gas (H) is kept away from:

(B) Windows

(D) Ventilation Intakes

(E) Soffit Vents

(F) Garage Doors

(G)Crawl spaces or other openings that can allow exhaust gas to enter inside or be drawninto a potentially occupied building

or structure.



Not for

Reproduction

• Nearby structures may be exposed to the engine exhaust (H) from the generator (A) and must be considered when

installing the standby generator.

• Wind and air currents should be taken into consideration when positioning the generator (A). Place the generator in an

area where winds will carry the exhaust gas (H) away from any potentially occupied building or structure.

• DO NOT place the standby generator (A) in any area where leaves or debris can accumulate.

Reduce The Risk of Fire

Obey the installation requirements listed below. The figures below illustrate the minimum distances from structures and

vegetation to reduce the risk of fire.

The National Fire Protection Association (NFPA) standard NFPA 37 establishes criteria for minimizing the hazard of fire

during the installation and operation of stationary combustion engines. NFPA 37 limits the spacing of an enclosed generator

from openings in walls, structures and combustible materials outside the enclosure. The following generator placement

requirements are based on compliance to NFPA 37.



WARNING

Exhaust heat/gases could ignite combustibles or structures resulting in death or serious injury.

• Exhaust outlet of enclosure must have at least 5 ft. (1.5m) minimum clearance from any structure, shrubs, trees, or any

kind of vegetation.

• Enclosure must be at least 5 ft (1.5m) from windows, doors, any wall opening, shrubs, or vegetation over 12 inches (30.5

cm) in height.

• Enclosure must have a minimum of 5 ft. (1.5 m) overhead clearance from any structure, overhang, or trees.

• DO NOT place enclosure under a deck or other type of structure that may confine airflow.

• Smoke detector(s) MUST be installed and maintained indoors according to the manufacturer’s instructions. Carbon

monoxide alarms cannot detect smoke.

• Do not place enclosure in a manner other than shown in illustrations.

Not for

Reproduction

Legend for Generator Locations to reduce the risk of fire:

(A) Standby Generator

Not for

Reproduction

(B)Standby enclosure must be at least 5 ft (1.5 m) from windows, doors, any wall opening, shrubs or vegetation over 12

inches (30.5 cm) in height.

(C)Exhaust outlet of standby enclosure must have at least 5 ft (1.5 m) minimum clearance from any structure, shrubs, trees

or any kind of vegetation.

(D)Standby enclosure must have a minimum of 5 feet (1.5 m) overhead clearance from any structure, overhang or trees.

(E)Standby enclosure must have a minimum of 18 inches (45.7 cm) clearance from any structures with or without a fire

rating.

Other General Location Guidelines

• Place the standby generator in a prepared location that is

flat and has provisions for water drainage.

• Install the standby generator in a location where sump

pump discharge, rain gutter down spouts, roof run-off,

landscape irrigation, or water sprinklers will not flood the

unit or spray the enclosure and enter any air inlet or outlet

openings.

• Install the standby generator where it will not affect or

obstruct any services (including covered, concealed and

underground), such as telephone, electric, fuel (natural

gas / LPG vapor), irrigation, air conditioning, cable, septic,

sewer, well and so forth.

• Install the standby generator where leaves, grass, snow,

etc will not obstruct air inlet and outlet openings. If

prevailing winds will cause blowing or drifting, you may

need to construct a windbreak to protect the unit.

Not for

Reproduction

Installation

This product is only for use as an optional generator system

which provides an alternate source of electric power

and to serve loads such as heating, refrigeration, and

communication systems that, when stopped during any power

outage, can cause discomfort or inconvenience.

Every effort has been made to make sure that the information

in this manual is accurate and current. However, we reserve

the right to change, alter, or otherwise improve the product

and this document at any time without prior notice.

Only current licensed electrical and plumbing professionals

can attempt generator system installations. Installations must

strictly comply with all applicable codes, industry standards,

laws and regulations.

Lifting the Generator

WARNING

Hazardous Voltage - Contact with power lines could

cause electric shock or burns, resulting in death or serious

injury.

• If lifting or hoisting equipment is used, DO NOT contact

any power lines.

• DO NOT lift or move generator without assistance.

Proper tools, equipment, and qualified personnel must be

used in all phases of handling and moving the generator. The

approximate weight of the generator is listed in theGenerator

Specificationssection.

Use the lifting holes (A) in the base of the generator to lift

the generator onto the concrete pad. Lift the generator in

accordance with OSHA or local lifting regulations. Retouch

any chipped paint with the supplied touch-up paint.



Cold Weather Kit

If the generator operates in temperatures below 30°F (-1°C),

it is HIGHLY RECOMMENDED that a Cold Weather Kit be

installed.

Cold Weather Kit, Part No. 6578 (Fortress models) includes:

• Battery warmer

• Battery stand

Cold Weather Kit, Part No. 6567 (Briggs & Stratton models)

includes:

• Oil warmer

• Battery warmer

• Battery stand

• Wire harness

These items are available at your local service dealer.

If you need more information, please

call800-732-2989between 8:00 AM and 5:00 PM CT.



Anchoring and Wind Rating

Concrete Anchoring of Unit to Poured or

Existing Slab

To achieve the listed wind rating, the generator must be

installed in strict compliance with this installation manual.

The product components must be of the material specified

and all screws must be installed in accordance with the

applicable provisions and the anchor manufacturer’s

published installation instructions.

The concrete slab/pad must meet the requirements below

and the generator must be anchored with the anchors

ofAnchor Types1 or 2.

Anchor Types

1. Qty (4) 3/8” SS ITW RED HEAD LDT, Anchor embedded

2 ½” (63.5mm) in 3000 psi concrete. 3” (76.2mm) from

the edge minimum, 6” (152.4mm) spacing minimum.

Not for

Reproduction

2. Qty (4) 3/8” SS Powers/Dewalt Power Stud +SD2

Anchor embedded 2 ½” (63.5mm) in 3000 psi concrete.

3” (76.2mm) from the edge minimum, 6” (152.4mm)

spacing minimum.

There are four 7/16” hole locations (A) in the base of the

generator in which to anchor the unit.



Concrete Slab/Pad Types

PAD DIMENSIONSWIND

RATING

MPH

PAD

MODEL

Width Length Thickness

CONCRETE

SPEC

Up to 140 Pre-cast

Pad

(contact

dealer)

37in

(939.8mm)

54.4in

(1381.8mm)

3in

(76.2mm)

3000 PSI

140 to 175 Pre-cast

Pad

(contact

dealer)

37in

(939.8mm)

54.4in

(1381.8mm)

4in

(101.6mm)

3000 PSI

140 to 175 Poured 38in

(965.2mm)

55in

(1397mm)

5in

(127mm)

3000 PSI

These items are available at your local service dealer.

NOTICE Unless mandated by local or state codes, or

required to achieve wind rating, a concrete slab/pad is not

required

Electrical and Fuel Inlet Locations

The 3/4 inch N.P.T. fuel inlet connector (A) and electrical inlet

locations (B) are shown below.

A ½ inch knock-out is provided for the electrical inlet. This

inlet may be enlarged or supplemented to accommodate a

maximum conduit size of 1-½ inches. Make sure that the

installed conduit(s) enter the unit in zone (C) as shown in the

drawing below so that they properly enter the electrical box

and do not interfere with the fully opened roof.

Access Panels

The generator enclosure has several access panels, as

shown.

The access panels and the components located behind them

are listed below:

(A) Roof (Control Panel, air filter, oil dipstick, and circuit

breaker)

engine starter)

(D) Control Panel Cover (field wiring and control wires)

(F) Battery Panel (battery and generator data label)

(H) Front Access Panel (oil drain and oil filter)

Not for

Reproduction

Each generator is shipped with a set of identical keys

fastened to the fuel solenoid.



Open the roof (A):

1. Insert key into lock (G) of front panel (H). Gently push

down on the roof above the lock to assist in turning the

key. Turn the key one quarter turn clockwise.

2. Lift the roof (A) to the open position.

Front panel removal (H):

1. Remove the two bolts (J) that secure the panel (H) to the

unit.

2. Lift the panel (H) to remove from unit.

Attach the front panel (H):

1. Put the panel (H) in the unit.

2. Attach the panel (H) with the two bolts (J).

Rear panel removal (C):

1. Make sure that the roof (A) is in the open position.

2. Remove the two bolts (B) that secure the panel (C) to the

unit.

3. Lift the panel (C) to remove it from the unit.

Attach the rear panel (C):

1. Slide the panel (C) into place on the unit.

2. Attach the panel with the two bolts (B).

Battery panel removal (G):

1. Make sure that the roof is in the open position.

2. Remove the two bolts (F) that secure the panel (G) to the

unit.

3. Lift up on the panel (G) and remove it.

Note:Fuse holder (E) is located behind the battery panel (G).

Attach battery panel (G):

1. Put the panel (G) in the unit.

2. Attach the panel (G) with the two bolts (F).

Fuel Installation Plan

WARNING

Propane and Natural Gas are extremely flammable

and explosive, which could cause burns, fire or explosion

resulting in death or serious injury.

• Installation must be performed by a licensed

professional.

• Install the fuel supply system according to NFPA 37 and

other applicable fuel-gas codes.

• Before placing the generator into service, the fuel

system lines must be properly purged and leak tested.

• NO leakage is permitted.

• DO NOT operate engine if smell of fuel is present.



NOTICE The supplied flexible fuel line is not to be

installed underground or in contact with the ground.

• The entire flexible fuel line must be visible for periodic

inspection and must not be concealed within nor contact

nor run through any wall, floor, or partition.

The information below is provided to assist gaseous fuel

system technicians in planning installations. In no way

should this information be interpreted to conflict with

applicable fuel gas codes. Consult with your local fuel

supplier or Fire Marshall if questions or problems arise.



WARNING

Propane and Natural Gas are extremely flammable

and explosive, which could cause burns, fire or explosion

resulting in death or serious injury.

• The generator is equipped with an automatic safety

gasfuel shut-off valve.

• DO NOT operate the equipment if the fuel shut-off valve

is missing or inoperative.

Not for

Reproduction

WARNING

Propane and Natural Gas are extremely flammable

and explosive, which could cause burns, fire or explosion

resulting in death or serious injury.

• LP gas is heavier than air and will settle in low areas.

• Natural gas is lighter than air and will collect in high

areas.

• The slightest spark could ignite these fuels and cause

an explosion.

• DO NOT light a cigarette or smoke.



TO THE INSTALLER:Consult with the generator owner(s)

and convey any technical considerations that can affect their

installation plans before applying these general guidelines.

The following general rules apply to gaseous fuel system

piping:

• The piping material must conform to federal and local

codes, be rigidly mounted, and be protected against

vibration.

• Piping should be protected from physical damage,

especially where it passes through flower beds, shrub

beds, and other cultivated areas where damage can

occur.

• Install the provided flexible fuel line (B) between the

generator fuel inlet port (A) and the rigid piping to

prevent thermal expansion and contraction from causing

excessive stress on the piping material.

• A union (C) or a flanged connection must be provided

downstream to permit removal.

• A manometer test port (D) should be installed for

vapor fuels. Use the port to install a manometer and

check if the engine receives the correct fuel pressure

for operation. A digital manometer (P/N 19495) or an

analogmanometeris available at your service center for

vapor fuels only. When the initial test runs are completed,

the manometer is removed and the port is plugged.

• For vapor fuels only: Where the formation of hydrates or

ice is known to occur, piping should be protected against

freezing. The termination of hard piping must include

a sediment trap (E) where condensate is not likely to

freeze.

• A minimum of one accessible, approved manual shutoff

valve (F) shall be installed in the fuel supply line within 6

ft (180 cm) of the generator.

• You must install a manual fuel shut-off valve in the interior

of the building.

• Where local conditions include earthquake, tornado,

unstable ground, or flood hazards, special consideration

shall be given to increase strength and flexibility of piping

supports and connections.

• Piping must be of the correct size to maintain the

required supply pressures and volume flow under

varying generator load conditions with all gas appliances

connected to the fuel system turned on andoperating.

• Use a pipe sealant or joint compound approved for

use with NG/LP on all threaded fittings to reduce the

possibility of leakage.

NOTICE Keep thread sealant out of the gas piping to

prevent component part damage.

• Installed piping must be properly purged and leak tested,

in accordance with applicable codes andstandards.



(A) Generator Fuel Inlet

(B)Flexible Fuel Line

(C)Union Fitting

(D)Manometer Test Port

(E)Sediment Trap

(F)Manual Shut-off Valve

Fuel Consumption

Estimated fuel supply requirements at half and full load for

natural gas and LP vapor fuels are shown below.

LP Vapor (Propane)

20 kW 17 kW

Cu Ft/Hr 135 118

Gal/Hr (liquid) 3.75 3.28

Full Load

BTU/Hr 337500 295000

Cu Ft/Hr 109 99

Gal/Hr (liquid) 3.03 2.75

3/4 Load

BTU/Hr 272500 247500

Cu Ft/Hr 83 74

Gal/Hr (liquid) 2.31 2.06

1/2 Load

BTU/Hr 207500 185000

Cu Ft/Hr 56 54

Gal/Hr (liquid) 1.56 1.5

1/4 Load

BTU/Hr 140000 135000

Cu Ft/Hr 40 40

Gal/Hr (liquid) 1.11 1.11

Exercise

BTU/Hr 100000 100000

Natural Gas

Not for

Reproduction

20 kW

(18 kW)

17 kW

15.3 kW

Cu Ft/Hr 260 248Full Load

BTU/Hr 260000 248000

Cu Ft/Hr 240 2183/4 Load

BTU/Hr 240000 218000

Cu Ft/Hr 187 1701/2 Load

BTU/Hr 187000 170000

Cu Ft/Hr 135 1281/4 Load

BTU/Hr 135000 128000

Cu Ft/Hr 99 99Exercise

BTU/Hr 99000 99000

Recommended

Energy Content of

FuelHeating Value:

LP Vapor Natural Gas

Heating Value:

BTU per gallon (gross**)

Cubic feet (gas)

91,547

2,500



1,000

Fuel Type

An important consideration affecting the entire installation

is the type of fuel used by your generator. The system was

factory tested and adjusted using natural gas, but can be

converted to use LP vapor. For correct engine function,

factors that are inherent to each of these fuels, like your

location and the duration of possible utility interruptions, are

important considerations in the following fuel guidelines:

• Use clean, dry fuel that is free of moisture or

any particulate material. Using fuels outside the

recommendation values that follow can cause

performance problems.

• In engines set up to run on propane (LP), commercial

grade HD5 propane with a minimum fuel energy of 2500

BTUs/ft3 with maximum propylene content of 5% and

butane and heavier gas content of 2.5% and minimum

propane content of 90% is required.

Natural gas rating will depend on specific fuel, but typical

derates are between 10 and20% of the LP gas rating.

Natural gas or LP engines are certified to operate on natural

or liquid propane gas. The emissions control system for this

engine is EM (Engine Modifications).

Fuel Pressure

Both LP vapor and natural gas fuel supply pressure at the

generator’s fuel inlet port and must be between the following

levels at full load with all gas appliances turned on and in

operation.

• NG is 3.5-7” W.C.

• LP is 11-14” W.C.

Make sure that all gas line shutoff valves are OPEN and

that adequate fuel pressure is available whenever automatic

operation is desired.

For Natural Gas fuel pressure levels of 3.5 - 5" W.C., replace

the regulator assembly with service kit 6331-00 (available at

your local service dealer).

Power Loss

Air density is less at high altitudes, resulting in less available

engine power. Engine power will decrease by 3.5% for each

1,000 feet (300 m) above sea level and by 1% for each

10° F (5.6°C) above 77°F (25°C). Generators located in

these conditions must have their transfer switch adjusted

appropriately for this power decrease. See your Automatic

Transfer Switch manual on how to adjust for the power

decrease.

The Gaseous Fuel System

Fuel Pipe Sizing

NFPA 54 and 58 are common resources. The installer must

consider the specific gravity of gas, compensate for a nominal

amount of restriction from bends and fittings, and refer to

federal and local codes for guidance.

Fuel Conversion

The engine of your home generator system is factory

Calibrated and set to operate on natural gas (NG). It may also

be operated on liquefied petroleum (LP) vapor.



NOTICE Units are set to NG at the factory.

To convert to either fuel, follow these steps:

1. Put the key into the lock of the front panel. Lightly push

down on the roof above the lock, and then turn the key

one quarter turn clockwise.

2. Lift the roof to the open position.

3. Push the control panel OFF button.

4. Remove the battery panel.

5. Remove the 15 Amp fuse.

6. Remove utility power to generator to de-energize the

battery charger.

7. Disconnect the negative (-) cable at the battery.

8. Remove the rear panel.

9. Find the fuel selector switch (A) on top of the fuel

regulator (B).

Not for

Reproduction

10. Set Fuel Selector:

A. Remove cap (C) from the Fuel Select Valve by sliding

it upward.

Note:If this is the first installation of this generator,

thecapwill be found in the parts bag.

B. LP or NG is selected by using the cap (C) as a tool to

rotate the indicator to the LP or NG mark (the image

below shows the FSV set to LP fuel).

C. Install the cap (C) after fuel selection is complete.

11. Once the fuel selection is complete, apply a drop of

cyanoacrylate (super) glue on the Fuel Select Cap.

12. Connect the negative (-) cable at the battery.

13. Install the rear panel.

14. Install 15-amp fuse.

15. Install the battery panel.

16. Push and hold the CONFIG button to access the

configuration menu.

17. Push SELECT to edit the items in the configuration menu.

18. To setup the generators control board for LP fuel you will

need to enter the Configuration Menu by using the Dealer

Password, which is available on the Power Portal.

19. Navigate to “SELECT PROFILE” and press select on the

correct profile for the generator. For example “20KW_LP”

for operating a 20kW unit running on LPfuel.

Note:Selecting a profile that is not intended for the generator

can cause the generator to run erratically and could result in

damage.

20. To Save the new fuel setting, press and hold the STOP/

CONFIG button until “Saving Settings…” is displayed.

21. For Additional information on the operation of the

generator controller please refer to the "Operation

Instructions GC1031 GENSET Controller Manual,"

PN:80086364.

22. Close the roof.

23. Restore utility power to generator.

24. Push the control board AUTO button.

Fuel Consumption

LP Vapor (Propane)

20kW 17kW

Full Load Cu Ft/Hr 135 118

Gal/Hr (liquid) 3.75 3.28

BTU/Hr 337,500 295,000

3/4 Load Cu Ft/Hr 109 99

Gal/Hr (liquid) 3.03 2.75

BTU/Hr 272,500 247,500

1/2 Load Cu Ft/Hr 83 74

Gal/Hr (liquid) 2.31 2.06

BTU/Hr 207,500 185,000

1/4 Load Cu Ft/Hr 56 54

Gal/Hr (liquid) 1.56 1.5

BTU/Hr 140,000 135,000

No Load Cu Ft/Hr 40 40

Gal/Hr (liquid) 1.11 1.11

BTU/Hr 100,000 100,000

Natural Gas

20kW 17kW

Full Load Cu Ft/Hr 260 248

BTU/Hr 260,000 248,000

3/4 Load Cu Ft/Hr 240 218

BTU/Hr 240,000 218,000

1/2 Load Cu Ft/Hr 187 170

BTU/Hr 187,000 170,000

1/4 Load Cu Ft/Hr 135 128

BTU/Hr 135,000 128,000

No Load Cu Ft/Hr 99 99

BTU/Hr 99,000 99,000

Recommended Energy

Content of Fuel:

Natural Gas Propane (LP Vapor)

Heating Value:

BTU per gallon liquid

(gross*)

N/A 91,547

Heating Value:

BTU per Cubic feet

(vapor)

1,000 2,500

Not for

Reproduction

Electrical Field Connections

WARNING

Generator and utility voltage could cause electrical shock or burn resulting in death or serious injury.

• Installation must be performed by a licensed professional.

• Disconnect all sources of electricity before installing or servicing equipment.

• Ground system before applying power.

WARNING

Hazardous Voltage -Installing low and high voltage wire in same conduit could cause electric shock or burns,

resulting in death or serious injury.

• Do not run low and high voltage wire in the same conduit unless the insulation rating on ALL wiring is rated for 600V.

See NFPA 70 for more information.

Low Voltage connections are made via a field connections terminal block (E) in main electrical area. Compare this illustration

with your generator to familiarize yourself with the location of these connections.

Legend for System Connector Location

(A)Two Pin Terminal Block — Used to connect utility 240 VAC from fuse block in ATS to the control board. Connect only one

wire per terminal. Use #14 [2.5mm2] AWG minimum 300 volt wire.

(B) Transfer Switch Connection — Controls Briggs & Stratton

transfer switch.

(D) E-Stop—For use with with optional external E-stop.

(E) Field Connections Terminal Block—Reference the table that follows.

(F)Power Connection (L1 and L2) — Power connection to transfer switch.

(G)Ground Connection — Connect to transfer switch ground wire.

Not for

Reproduction

La page charge ...

Simplicity 040589-00 Guide d'installation

Marque: Simplicity

Modèle: 040589-00

Catégorie: Groupes électrogènes

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 040589-00 Installation guide
español: Simplicity 040589-00 Guía de instalación

Simplicity 040589-00 Guide d'installation

Ce manuel convient également à

Simplicity 040589-00 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents