Hitachi NV 75AN Instruction And Safety Manual

Instruction and safety manual

Manuel d’instructions et de sécurité

Instrucciones y manual de seguridad

Model

Modèle

Modelo

NV 75AN • NV 75AN(S)

NV 75AN(S1) • NV 75AN(S2)

Nailer

Cloueur

Clavador

NV75AN

(contact actuation and toe-nailing tip model)

NV75AN(S)

(single sequential actuation and toe nailing model)

NV75AN(S1)

(contact actuation and ﬂ at tip model)

NV75AN(S2)

(single sequential actuation and ﬂ at tip model)

DANGER

Improper use of this Nailer can result in death or serious injury!

This Manual contains important information about product safety.

Read and understand this Manual before operating the Nailer.

Never allow anyone who has not reviewed this manual to use the tool.

This manual should be stored in safe place.

DANGER

Une utilisation incorrecte et sans respecter la sécurité de ce cloueur risque d’entraîner la

mort ou des blessures graves !

Ce manuel renferme des instructions importantes sur la sécurité de l’outil.

Lire et bien assimiler ce manuel avant d’utiliser le cloueur.

Cet outil ne doit jamais être utilisé par une personne n’ayant pas pris connaissance du manuel.

Ce mode d’emploi doit être conservé dans un endroit sûr.

PELIGRO

¡La utilización inadecuada e insegura de este clavador puede resultar en lesiones serias o

en la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y entienda este manual antes de utilizar el martillo neumático.

La herramienta no deberá utilizarse sin haber leído previamente este manual.

Este manual debe ser guardado en un lugar seguro.

English

Page Page

Français

Page Page

Español

Página Página

CONTENTS

TABLE DES MATIÈRES

ÍNDICE

IMPORTANT SAFETY INFORMATION ....................3

DEFINITIONS OF SIGNAL WORDS .........................3

EXPLANATION OF THE NAILING ACTION OF THE

HITACHI NAILER .................................................3

SAFETY

IMPORTANT SAFETY INSTRUCTIONS -

FOR USING NAILERS .........................................4

RESPONSIBILITIES OF EMPLOYER, TOOL

OWNER AND TOOL OPERATOR .......................8

FUNCTIONAL DESCRIPTION

NAME OF PARTS .....................................................9

SPECI FICAT IONS ................................................... 10

NAIL SELECTION ...................................................10

ACCESSORIES.......................................................10

STANDARD ACCESSORIES............................. 10

OPTIONAL ACCESSORIES .............................. 11

OPERATING INSTRUCTIONS

APPLICATIONS ...................................................... 11

BEFORE OPERATION ............................................ 11

WORKING ENVIRONMENT .............................. 11

AIR SUPPLY ...................................................... 11

LUBRICATION ................................................... 12

COLD WEATHER CARE ................................... 12

TESTING THE NAILER ..................................... 12

ADJUSTING AIR PRESSURE ........................... 14

LOADING NAILS ............................................... 14

NAILER OPERATION ............................................. 15

METHODS OF OPERATION ............................. 16

ADJUSTING THE NAILING DEPTH .................. 18

CHANGING THE EXHAUST DIRECTION......... 18

USING THE NOSE CAP .................................... 18

MAINTENANCE

MAINTENANCE AND INSPECTION ...................... 19

SERVICE AND REPAIRS ........................................21

PARTS LIST ............................................................66

INFORMATION IMPORTANTE DE SÉCURITÉ ......23

DEFINITION DES MOTS DE SIGNALISATION ......23

EXPLICATION DE L’ACTION DE CLOUAGE DU

CLOUEUR HITACHI ..........................................23

SECURITE

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR

L’UTILISATION DU CLOUEUR .......................... 24

RESPONSABILITÉS DE L’EMPLOYEUR,

DU PROPRIÉTAIRE DE L’OUTIL ET DE

L’OPÉRATEUR DE L’OUTIL ...............................28

DESCRIPTION FONCTIONNELLE

NOM DES PIECES ..................................................29

SPECI FICAT IONS ...................................................30

SELECTION DES CLOUS ......................................30

ACCESSOIRES.......................................................30

ACCESSOIRES STANDARD.............................30

ACCESSOIRES EN OPTION ............................31

INSTRUCTIONS D’OPÉRATION

APPLICATIONS ...................................................... 31

AVANT L’UTILISATION ...........................................31

ENVIRONNEMENT DE TRAVAIL ...................... 31

ALIMENTATION D’AIR ....................................... 31

GR AISSAGE ......................................................32

ENTRETIEN PAR TEMPS FROID .....................32

ESSAI DU CLOUEUR ........................................32

RÉGLAGE DE LA PRESSION D’AIR .................34

CHARGEMENT DES CLOUS ............................34

UTILISATION DU CLOUEUR ..................................36

MÉTHODES D’UTILISATION ............................37

RÉGLAGE DE LA PROFONDEUR DE CLOUAGE

...39

CHANGEMENT DU SENS D’ECHAPPEMENT

...39

UTILISATION DU CAPUCHON DE BEC ...........39

ENTRETIEN

ENTRETIEN ET INSPECTION ................................40

ENTRETIEN ET REPARATIONS ............................42

LISTE DES PIÈCES ................................................66

INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD

...44

DEFINICIÓN DE LAS PALABRAS CLAVE .............44

EXPLICACIÓN LA ACCIÓN DE CLAVADO DEL

CLAVADOR HITACHI ........................................44

SEGURIDAD

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA LA UTILIZACIÓN DEL CLAVADOR ........45

RESPONSABILIDADES DEL EMPLEADOR, EL

PROPIETARIO DE LA HERRAMIENTA Y EL

OPERADOR DE LA HERRAMIENTA ................49

DESCRIPCIÓN FUNCIONAL

NOMENCL ATURA .................................................. 50

ESPECIFICACIONES ............................................. 51

SELECCIÓN DE CLAVOS ...................................... 51

ACCESORIOS ........................................................ 51

ACCESORIOS ESTÁNDAR ............................... 51

ACCESORIOS OPCIONALES...........................52

INSTRUCCIONES DE OPERACIÓN

APLICACIONES ...................................................... 52

ANTES DE LA OPERACIÓN ...................................52

ENTORNO DE TRABAJO .................................52

SUMINISTRO DE AIRE .....................................52

LUBRICACIÓN ..................................................53

CUIDADOS PARA CLIMAS FRÍOS ...................53

PRUEBA DEL CLAVADOR ................................54

AJUSTE DE LA PRESIÓN DE AIRE ..................55

CARGA DE CLAVOS .........................................55

OPERACIÓN DEL CLAVADOR ..............................57

MÉTODOS DE OPERACIÓN ............................58

AJUSTE DE LA PROFUNDIDAD DE CLAVADO

... 60

CAMBIO DEL SENTIDO DEL AIRE DE ESCAPE

...6 0

UTILIZACIÓN DE LA TAPA PARA EL MORRO

...6 0

MANTENIMIENTO

MANTENIMIENTO E INSPECCIÓN .......................61

SERVICIO Y REPARACIONES ...............................63

LISTA DE PIEZAS ..................................................66

3

English

IMPORTANT SAFETY INFORMATION

Read and understand tool labels and all of the operating instructions, safety precautions and warnings

in this manual before operating or maintaining this Nailer.

Failure to follow warnings could result in DEATH or SERIOUS INJURY

Most accidents that result from the operation and maintenance of Nailers are caused by the failure to observe basic

safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it

occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Manual and in the sections which contain the

operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by DANGERS and WARNINGS

on the Nailer and in this Manual.

NEVER use this Nailer for applications other than those speciﬁ ed in this Manual.

DEFINITIONS OF SIGNAL WORDS

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

EXPLANATION OF THE NAILING ACTION OF THE HITACHI NAILER

○

SINGLE SEQUENTIAL ACTUATION MECHANISM:

First, press the push lever against the wood; next, pull the trigger to drive the fastener.

After nailing once, nailing will not be possible again until the Trigger is released and pressed again.

○

CONTACT ACTUATION MECHANISM:

First, press the push lever against the wood; next, pull the trigger to drive the fastener.

First, pull the trigger; next, press the push lever against the wood to drive the fastener.

If the Trigger is held back, a nail will be driven each time the Push Lever is pressed against the wood.

4

English

SAFETY

IMPORTANT SAFETY INSTRUCTIONS - FOR USING NAILERS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

●

General

To reduce the risks of electric shock, ﬁ re, and injury to persons, READ ALL THE INSTRUCTIONS BEFORE

USING THE TOOL.

DANGER

1. OPERATORS AND OTHERS IN WORK AREA

MUST WEAR EYE PROTECTION (SAFETY

GLASSES WITH SIDE SHIELDS).

When operating the Nailer, always wear

safety glasses with side shields, and

make sure others in work area wear

safety glasses, too.

Safety glasses must conform to the

requirements of American National

Standards Institute, ANSI Z87.1 and

provide protection against ﬂ ying particles

both from the front and side.

Ordinary eyeglasses do not provide

adequate protection.

The employer must enforce the use of

safety glasses by the Nailer operator and

others in work area.

WARNING

3. NEVER POINT TOOL AT YOURSELF OR OTHERS

IN WORK AREA.

Always assume that the Nailer contains

fasteners.

Never point the Nailer toward yourself or

others, whether it contains fasteners or

not.

If fasteners are mistakenly driven, it can

lead to severe injuries.

Never engage in horseplay with the

Nailer.

Respect the Nailer as a working

implement.

2. NEVER USE REACTIVE GASES OR OTHER

BOTTLED GASES. EXPLOSION MAY OCCUR.

Never use reactive gases such as

oxygen, combustible gases or any other

bottled gases as a power source for the

Nailer.

Use of the above gases is dangerous, as

the Nailer will explode.

Use only clean, dry, regulated

compressed air.

4. DO NOT PLACE FINGER ON TRIGGER AND KEEP

FINGERS AWAY FROM TRIGGER WHEN NOT

DRIVING FASTENERS TO AVOID ACCIDENTAL

DISCHARGE.

Never carry the Nailer with ﬁ nger on Trigger since

you could drive a fastener unintentionally and injure

yourself or someone else.

Always carry the Nailer by the handle only.

5. KNOW AND UNDERSTAND WHAT TRIGGER

SYSTEM YOU ARE USING.

Read and understand section titled “METHODS OF

OPERATION.” (pages 16 – 18)

6. DO NOT MAKE CONTACT WITH SAFETY

TIP (PUSH LEVER) WHEN NOT DRIVING

FASTENERS.

5

English

SAFETY — Continued

WARNING

When using tools, basic precautions should always be followed, Including the following:

1. Work area

(1) Keep the work area clean and well lighted.

Cluttered benches and dark areas increase the risks

of electric shock, ﬁ re, and injury to persons.

(2) Do not operate the Nailer in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases, or combustible dust.

The Nailer is able to create sparks resulting in the

ignition of the dust or fumes.

(3) Keep bystanders, children, and visitors away

while operating the Nailer. Distractions are able to

result in the loss of control of the Nailer.

2. Personal safety

(1) Stay alert. Focus on your work and use common

sense when working with the Nailer. Do not use

the Nailer while tired, after having consumed

drugs or alcohol, or while under the inﬂ uence of

medication.

A moment of inattention while operating the Nailer

increases the risk of injury to persons.

(2) Dress properly. Do not wear loose clothing or

jewelry. Contain long hair. Keep hair, clothing,

and gloves away from moving parts.

Loose clothes, jewelry, or long hair increases the

risk of injury to persons as a result of being caught in

moving parts.

(3) Avoid unintentional starting. Be sure the switch

is oﬀ before connecting to the air supply. Do

not carry the Nailer with your ﬁ nger on the switch or

connect the Nailer to the air supply with the switch on.

(4)

WARNING

– Disconnect the Nailer from

the air source before making adjustments, doing

Nailer maintenance, clearing jams, touching

the Push Lever, attaching or removing the nose

cap, when not in use, leaving work area, leaving

the Nailer outside of the operator's supervision

or control, loading, or unloading the Nailer,

handing it to another person, elevating, lowering

or otherwise moving the Nailer to a new location.

Never attempt to clear a jam or repair the Nailer

unless you have disconnected air hose from the

Nailer and removed all remaining fasteners from the

Nailer. The Nailer should never be left unattended

since people who are not familiar with the Nailer

might handle it and injure the themselves.

Such precautionary measures reduce the risk of

injury to persons.

(5) Do not overreach. Keep proper footing and

balance at all times. Proper footing and balance

enables better control of the Nailer in unexpected

situations.

(6) Use safety equipment. A dust mask, non-skid

safety shoes and a hard hat must be used for the

applicable conditions.

(7)

WARNING

– Risk of hearing loss. Wear

hearing protection.

Hearing protection shall have a Noise Reduction

Rating (NRR) determined in accordance with US

Environmental Protection Agency rules that is

appropriate for noise exposure.

(8) Always wear head protection.

Always wear head protection to protect your

head from ﬂ ying objects.

(9) Do not attach the hose or Nailer to your body.

Attach the hose to the structure to reduce the risk of

loss of balance if the hose shifts.

(10)

WARNING

– Drive Nails into proper work

surface only. Do not drive nail into other nails. This

is able to cause the fastener to be deﬂ ected and hit

someone, or cause the Nailer to react and result in a

risk of injury to persons.

3. Nailer use and care

(1) Use clamps or another practical way to secure

and support the workpiece to a stable platform.

Holding the work by hand or against the body is

unstable and is able to lead to loss of control.

(2) Do not force the Nailer. Use the correct Nailer for

the application. The correct Nailer will do the job

better and safer at the rate for which the Nailer is

designed.

(3) Do not use the Nailer if the switch does not

turn the Nailer on or oﬀ . Any Nailer that cannot be

controlled with the switch is dangerous and must be

repaired.

Never use Nailer which is defective or operating

abnormally. If the Nailer appears to be operating

unusually, making strange noises, or otherwise

appears defective, stop using it immediately and

arrange for repairs by a Hitachi authorized service

center.

6

English

(4) Disconnect the Nailer from the air source before

making any adjustments, changing accessories,

or storing the Nailer. Such preventive safety

measures reduce the risk of starting the Nailer

unintentionally.

(5) Store the Nailer when it is idle out of reach of

children and other untrained persons. A Nailer is

dangerous in the hands of untrained users.

(6) Maintain the Nailer with care. Keep the

Nailer Clean and lubricated for better and safer

performance.

(7) Check for misalignment or binding of moving

parts, breakage of parts, and any other condition

that may aﬀ ect the Nailer's operation.

If damaged, have the Nailer serviced before using.

Because of high air pressure in the Nailer, cracks in

the surface are dangerous. To avoid this, do not drop

the Nailer or strike the Nailer against hard surfaces;

and do not scratch or engrave signs on the Nailer.

Many accidents are caused by poorly maintained

Nailers. There is a risk of bursting if the Nailer is

damaged.

(8) Do not use the Nailer that is not in proper

working order. Tags and physical segregation

shall be used for control.

(9) Use only accessories that are identiﬁ ed by

Hitachi for the speciﬁ c Nailer. Use of an accessory

not intended for use with the speciﬁ c Nailer ,

increases the risk of injury to persons.

(10) Use only those fasteners listed in the

Accessories section of this manual. Fasteners not

identiﬁ ed for use with this Nailer by Hitachi are able to

result in a risk of injury to persons or Nailer damage

when used in this Nailer.

4. Service

(1) Tool service must be performed only by qualiﬁ ed

repair personnel.

(2) When servicing a Nailer, use only identical

replacement parts. Use only authorized parts.

(3) Use only the lubricants supplied with the Nailer

or speciﬁ ed by Hitachi.

5. Air source

(1) Never connect to an air source that is capable

of exceeding 200 psi (13.7 bar 14 kgf/cm

2

) if a

regulator fails.

Over pressurizing the Nailer is able to result in

bursting, abnormal operation, breakage of the Nailer

or serious injury to persons.

DO NOT EXCEED 120 psi (8.3 bar 8.5 kgf/cm

2

).

Use only clean, dry, regulated compressed air at the

rated pressure or within the rated pressure range as

marked on the Nailer.

Always verify prior to using the Nailer that the air

source has been adjusted to the rated air pressure or

within the rated air-pressure range.

(2) Never use reactive gases such as oxygen,

carbon dioxide, combustible gases or any

bottled gas as an air source for the Nailer. Such

gases are capable of explosion and serious injury to

persons.

6. Others

(1) Be careful of double ﬁ re and being hit by the

Nailer due to spring back (“recoil”).

After driving a nail, the Nailer may recoil causing it to

move away from the work surface.

To reduce risk of injury always manage recoil by:

1) always maintaining control of the Nailer.

2) allowing recoil to move the Nailer away from work

surface.

3) not resisting recoil such that the Nailer will be

forced back into the work surface. In “CONTACT

ACTUATION MECHANISM”, if push lever is

allowed to re-contact work surface before the

trigger is released, an unintended discharge of a

nail will occur. In order to avoid this undesirable

double ﬁ re,

○

Intermittent operation (Trigger ﬁ re)

1

Pull the trigger rapidly and ﬁ rmly.

2

Release the trigger QUICKLY.

SAFETY — Continued

WARNING

7

English

○

Continuous operation (Push lever ﬁ re)

1

Do not press the Nailer against the wood with

excessive force.

2

Separate the Nailer from the wood as it recoils

after nailing.

4) keeping face and body parts away from the Nailer.

(2) Never use NON relieving coupler on Nailer. If a

non relieving coupler is used on the Nailer, the Nailer

can remain charged with air after disconnecting

and thus will be able to drive a fastener even after

disconnecting. The Nailer and air hose must have a

hose coupling such that all pressure is removed from

the Nailer when the coupling joint is disconnected.

(3) Check Push Lever before use. Make sure the

Push Lever operates properly, and is not inoperable,

disconnected, or altered. (The Push Lever may be

called “Safety”.) Never use the Nailer unless the Push

Lever is operating properly, otherwise the Nailer

could drive a fastener unexpectedly. Do not tamper

with or remove the Push Lever, or otherwise cause

the Push Lever to become inoperable.

(4) Keep all screws and covers tightly in place. Keep

all screws and covers tightly mounted.

Check their condition periodically. Never use the

Nailer if parts are missing or damaged.

(5) Do not load fasteners with Trigger or Push Lever

depressed. When loading fasteners into the Nailer

or when connecting the air hose,

1) do not depress the Trigger;

2) do not depress the Push Lever; and

3) keep the Nailer pointed downward.

(6) Keep hands and body away from ﬁ ring head

during use. Never place your hands or feet closer

than 8 inches (200 mm) from the ﬁ ring head. A

serious injury can result if the fasteners are deﬂ ected

by the workpiece, or are driven away from the point of

entry.

(7) When working close to an edge of a workpiece

or at steep angles, or driving fasteners into

thin workpiece use care to minimize chipping,

splitting or splintering, or free ﬂ ight, ricochet or

piercing of fasteners, which may cause injury.

(8) Never drive fasteners from both sides of a wall

at the same time. The fasteners can be driven into

and through the wall and hit a person on the opposite

side.

(9) Use extra caution when driving the Nailer into

existing walls or other blind areas to prevent

contact with hidden objects or persons on other

side (eg., wires, pipes).

(10) Check for live wires. Avoid the risk of severe

electrical shock by checking for live electrical wires

that may be hidden by walls, ﬂ oors or ceilings. Turn

oﬀ the breaker switch to ensure there are no live

wires.

(11) Do not lift, pull or lower the Nailer by the hose.

(12) Do not disconnect air hose from Nailer with

ﬁ nger on Trigger. The Nailer can ﬁ re when re-

connected to An air supply.

(13) Handle Nailer correctly. Operate the Nailer

according to this Manual. Never allow the Nailer to

be operated by children, individuals unfamiliar with its

operation or unauthorized personnel.

(14) Never use Nailer for applications other than

those speciﬁ ed in this manual.

(15) Never modify or alter a Nailer. Doing so may cause

it to malfunction and personal injuries may result.

(16) Do not remove Dust Cover. Fragments of wire

collating fasteners can ﬂ y out.

(17) Close Nail Guide and do not open it during

operation. If driving fasteners with the Nail Guide

open, the fasteners can be driven away from the

workpiece.

SAFETY — Continued

WARNING

8

English

RESPONSIBILITIES OF EMPLOYER, TOOL OWNER AND TOOL OPERATOR

1. Ensure that this MANUAL is available to operators

and personnel performing maintenance.

2. Train the operator in the safe use of the Nailer as

described in this MANUAL.

3. Ensure that only persons who have read and

understand this MANUAL operate the Nailer.

4. Ensure that Nailers are used only when operators and

others in work area are wearing EYE PROTECTION,

and other appropriate personal protective equipment

such as HEAD, HEARING, FOOT PROTECTION.

5. Enforce the use of EYE PROTECTION by operators

and others in work area.

6. Ensure that Nailers are kept in safe working order as

described in this MANUAL.

7. Maintain Nailers properly.

8. Ensure that only qualiﬁ ed personnel shall repair

Nailers.

9. Ensure that Nailers that require repair are removed

from service and that tags and physical segregation

are used as a means of control.

SAVE THIS MANUAL AND

KEEP IT AVAILABLE FOR OTHERS!

SAFETY — Continued

9

English

Nail Stopper

NOSE PART

Nail Guide

Feeder

Feed Piston

Feed Spring

NV75AN(S1) • NV75AN(S2) NV75AN • NV75AN(S)

FUNCTIONAL DESCRIPTION

NOTE: The information contained in this Manual is designed to assist you in the safe operation of the Nailer.

Some illustrations in this Manual may show details or attachments that diﬀ er from those on your own Nailer.

NAME OF PARTS

Nose

Piston

Piston O-ring

Exhaust Cover

Driver Blade

Nail Stopper

Outlet (Firing Head)

Body

Trigger

Switching Device

Cap

Magazine Cover

Nail Holder

Magazine Assembly

Dust Cover

Air Plug

Knob

Push Lever

Magazine

NOSE PART

Nail Guide

Feeder

Feed Piston

Feed Spring

Push Lever

(Flat tip)

Push Lever

(Toe-nailing tip)

10

English

SPECIFICATIONS

Operating pressure 70 – 120 psi (4.9 – 8.3 bar 5 – 8.5 kgf/cm

2

)

Dimensions

Length × Height × Width

12-21/64" × 12-7/16" × 5-13/64"

(313 mm × 316 mm × 132 mm)

Weight 6.3 lbs (2.9 kg)

Nail capacity 200 – 300 nails (1 coil)

Air consumption

.085 ft

3

/cycle at 100 psi

(2.4 ltr/cycle at 6.9 bar)

(2.4 ltr/cycle at 7 kgf/cm

2

)

Air inlet 3/8 NPT Thread

NAIL SELECTION

WARNING

●

Be sure to use only the genuine HITACHI nails for the NV75AN/NV75AN(S)/NV75AN(S1)/NV75AN(S2). The

use of any other nails can result in tool malfunction and/or nail breakdown, leading to serious injuries.

Only nails shown in the Table below can be driven with this Nailer.

Wire-collated coil nails

Min. Max.

.099"

(2.5 mm)

1-3/4" (45 mm)

.236"

(6 mm)

.131"

(3.3 mm)

3" (75 mm)

.283"

(7.2 mm)

ACCESSORIES

WARNING

●

Accessories other than those shown below can lead to malfunction and resulting injuries.

STANDARD ACCESSORIES

1

3

NV75AN, NV75AN(S), NV75AN(S1), NV75AN(S2)

1

Eye protection ..........................................................1

NV75AN, NV75AN(S)

2

Nose cap ..................................................................1

NV75AN, NV75AN(S1)

3

Sequential actuation trigger kit .................................1

2

11

English

OPTIONAL ACCESSORIES

... sold separately

○

Pneumatic Tool Lubricant

.8 oz. (25 cc) oil feeder (Code No. 877153)

4 oz. (120 cc) oil feeder (Code No. 874042)

1 quart (1 ltr) can (Code No. 876212)

NOTE: Accessories are subject to change without any

obligation on the part of HITACHI.

OPERATING INSTRUCTIONS

APPLICATIONS

○

Making wooden palettes, drums, and export wooden

boxes.

○

Packing operations in manufacturing plants, and

other types of packing and crating work in general.

○

Construction wooden work such as ﬂ oor and wall

framing, roof decking, subﬂ ooring.

○

Mobile and modular home construction.

BEFORE OPERATION

Read section titled “SAFETY” (pages 4 – 8).

Make sure of the followings before operation.

WORKING ENVIRONMENT

WARNING

●

No ﬂ ammable gas, liquid or other ﬂ ammable

objects at worksite.

●

Clear the area of children or unauthorized

personnel.

AIR SUPPLY

DANGER

●

NEVER use reactive gases or

other bottled gases.

Explosion may occur.

WARNING

●

Never connect Nailer to pressure

which potentially exceeds 200 psi

(13.7 bar 14 kgf/cm

2

) if a regulator fails.

●

Never use non relieving coupler on Nailer.

1. Power source

○

Use only clean, dry, regulated compressed air as a

power source for this Nailer.

○

Air compressors used to supply compressed air to

this Nailer must comply with the requirements of

the latest version of ANSI Standard B 19.3 “Safety

Standard For Compressors For Process Industries.”

○

Moisture or oil in the air compressor may accelerate

wear and corrosion in the Nailer.

Drain daily.

2. Filter-Regulator-Lubricator

○

Use a regulator with a pressure range of 0 – 120 psi

(0 – 8.3 bar 0 – 8.5 kgf/cm

2

).

○

Filter-regulator-lubricator units supply an optimum

condition for the Nailer and extend the Nailer life.

These units should always be used.

Filter ............ The ﬁ lter removes moisture and dirt

mixed in compressed air.

Drain daily unless ﬁ tted with an

automatic drain.

Keep the ﬁ lter clean by regular

maintenance.

Regulator ......The regulator controls the operating

pressure for safe operation of the Nailer.

Inspect the regulator before operation to

be sure it operates properly.

Lubricator .... The lubricator supplies an oil mist to the

Nailer.

Inspect the lubricator before operation

to be sure the supply of lubricant is

adequate.

Use Hitachi pneumatic tool lubricant.

12

English

○

Filter-regulator-lubricator units should always be

used.

Keep the lubricator ﬁ lled with Hitachi pneumatic tool

lubricant.

○

If a lubricator is not available, supply 5 – 10 drops of

Hitachi pneumatic tool lubricant into the air plug on

the Nailer twice a day.

COLD WEATHER CARE

○

Do not store the Nailer in a cold weather environment.

Keep the Nailer in a warm area until beginning the

work.

○

If the Nailer is already cold, bring it in a warm area

and allow the Nailer to warm up before use.

1

Reduce the air pressure to 64 psi (4.4 bar

4.5 kgf/cm

2

).

2

Remove all nails from the Nailer.

3

Connect the air hose and free-ﬁ re (blank-ﬁ re) the

Nailer.

The lowered air pressure will be enough to free-

ﬁ re the Nailer.

Slow speed operation tends to warm up the

moving part.

CAUTION

●

Do not free-ﬁ re the Nailer at high pressure.

TESTING THE NAILER

DANGER

●

Operators and others in work

area MUST wear safety

glasses with side shields

which conforms to ANSI Z87.1

speciﬁ cations.

Ordinary eyeglasses do not

provide adequate protection.

WARNING

●

Never use Nailer unless push lever is

operating properly.

Before actually beginning the nailing work, test the Nailer

by using the checklist below. Conduct the tests in the

following order.

If abnormal operation occurs, stop using the Nailer and

contact a Hitachi authorized service center immediately.

(1) DISCONNECT AIR HOSE FROM NAILER.

REMOVE ALL NAILS FROM NAILER.

□

ALL SCREWS MUST BE TIGHTENED.

If any screws are loose, tighten them.

Nailer Side

Filter

Lubricator

Compressor Side

Regulator

3. Air hose

Compressed air supply hoses shall have a minimum

working pressure rating equal to or greater than the

pressure from the power source if a regulator fails, or

150 psi (10.4 bar 10.6 kgf/cm

2

), whichever is greater.

4. Air consumption

Using the Air consumption table and the Air

compressor size formula, ﬁ nd a correct compressor

size.

Air consumption table

Operating pressure

psi

(bar)

(kgf/cm

2

)

80

(5.5)

(5.6)

90

(6.2)

(6.3)

100

(6.9)

(7)

Air consumption

ft

3

/cycle

(Itr/cycle)

.071

(2.0)

.081

(2.3)

.085

(2.4)

Air compressor size formula

Amount of air required

=number of Nailers

× average nails driven each minute per Nailer

× air consumption at given air pressure

× safety factor (always 1.2)

Example: 2 Nailers operating at 100 psi driving 30

nails per minute

Amount of air required

=2 × 30 × .085 (2.4) × 1.2

=6.1 CFM (ft

3

/min) (173 ltr/min)

After making the calculations as shown above, you

should ﬁ nd a compressor providing 6.1 CFM of air

that is required.

LUBRICATION

It is important that the Nailer be properly lubricated.

Without proper lubrication, the Nailer will not work

properly and parts will wear prematurely.

○

Use Hitachi pneumatic tool lubricant.

Do not use detergent oil or additives. These lubricants

will harm the O-rings and other rubber parts. This will

cause the Nailer to malfunction.

13

English

□

THE PUSH LEVER AND TRIGGER MUST MOVE

SMOOTHLY.

Push Lever

Trigger

Do not connect

air hose

(2) Adjust the air pressure to 70 psi (4.9 bar 5 kgf/cm

2

).

Connect the air hose.

(3) REMOVE ALL NAILS FROM NAILER.

CONTACT ACTUATION MECHANISM

Identiﬁ ed by: BLACK TRIGGER

(1) With the Nailer oﬀ the wood, pull the Trigger.

Next, depress the Push Lever against the wood.

□ THE NAILER MUST OPERATE.

(2) Next, depress the Push Lever against the workpiece.

Now pull the Trigger.

□ THE NAILER MUST OPERATE.

(3) If no abnormal operation is observed, you may load

nails in the Nailer.

Drive nails into the workpiece that is the same type to

be used in the actual application.

□

THE NAILER MUST OPERATE PROPERLY.

SINGLE SEQUENTIAL ACTUATION

MECHANISM

Identiﬁ ed by: RED TRIGGER

(1) Remove the ﬁ nger from the trigger and press the

push lever against the wood.

□

THE NAILER MUST NOT OPERATE.

Do not pull Trigger

Depress

Push Lever

(2) Separate the push lever from the wood.

Next, point the nailer downward, pull the trigger and

then wait in that position for 5 seconds or longer.

□

THE NAILER MUST NOT OPERATE.

Pull Trigger

14

English

(2) Adjust the position of the plate according to the nail

length.

The nail will not feed smoothly if the plate is not

correctly adjusted.

Magazine

Nail holder

Magazine cover

NOTE: Before loading nails in the magazine, adjust

the plate. If the magazine cover is forcibly

closed without adjusting the plate correctly,

the nail holder may be damaged.

1

Slide in vertical direction possible.

Lift or lower the nail holder to accept diﬀ erent

length nails.

2

Adjust the plate to the nail length reference points

on the magazine cover and turn the nail holder 45

degrees.

Nail holder

Magazine

2

1

3

/4", 2"

2

1

/4", 2

1

/2"

3"

(3) Place the nail coil into the magazine.

Uncoil enough nails to reach the driving hole.

Magazine

Nail holder

Nails

(3) First pull the Trigger.

Next, depress the Push Lever against the wood.

□

THE NAILER MUST NOT OPERATE.

(4) Without touching the Trigger, depress the Push Lever

against the wood.

Next, pull the Trigger.

□ THE NAILER MUST OPERATE.

ADJUSTING AIR PRESSURE

WARNING

●

Do not exceed

120 psi (8.3 bar

8.5 kgf/cm

2

).

Adjust the air pressure at recommended operating

pressure 70 – 120 psi (4.9 – 8.3 bar 5 – 8.5 kgf/cm

2

)

according to the length of nails and the hardness of

workpiece.

The correct air pressure is the lowest pressure which will

do the job. Using the Nailer at a higher than required air

pressure unnecessarily over stresses the Nailer.

LOADING NAILS

WARNING

●

When loading nails into Nailer,

1) do not pull trigger;

2) do not depress push lever; and

3) keep Nailer pointed downward.

(1) Grip the nail guide and knob with ﬁ nger.

Pull the knob down and swing the nail guide open.

And open the magazine cover.

Knob

Nail guide

Magazine cover

15

English

(4)

1

Uncoil enough nails to reach the driving hole.

2

Insert the ﬁ rst nail into the driving hole and the

second nail between the two pawls of the feeder.

3

Fit the nail heads in the guide slot.

Nail Guide

First nail

Feeder

Guide surface

Driving hole

Guide slot

1

4

3

2

4

Pulling the nails to the right, swing the nail guide

closed.

(5) Close the magazine cover ﬁ rst and swing the nail

guide closed.

(6) Lock the knob correctly.

Magazine cover

Nail guide

Knob

NOTE: Be careful not to deform the collated wires and

not to disengage the nails with the guide surface.

Otherwise, the nail guide will not close correctly.

NAILER OPERATION

Read section titled “SAFETY” (pages 4 – 8).

DANGER

●

Operators and others in work

area MUST wear safety

glasses with side shields

which conforms to ANSI Z87.1

speciﬁ cations.

Ordinary eyeglasses do not

provide adequate protection.

WARNING

●

Only person who have read

and understand this

MANUAL should operate the

Nailer.

●

NEVER point tool at yourself

or others in work area.

●

Keep ﬁ ngers AWAY from trigger when not

driving nails to avoid accidental discharge.

●

Know and understand what trigger system

you are using.

Please read and understand “Methods of

Operation” below.

●

Before starting work, check the types of

operation to drive nails.

●

Never place your hands or body closer than 8

inches (200 mm) from ﬁ ring head when using.

●

Do not drive nails into other nails; nails can

ricochet and hurt someone.

●

Do not actuate Nailer unless Nailer is placed

ﬁ rmly against the workpiece.

●

In order to avoid double ﬁ re or unwanted

ejection of a nail due to bouncing of the

Nailer,

1) do not push Nailer on workpiece with

strong force;

2) take Nailer away from workpiece using

recoil;

3) release trigger quickly when performing

trigger ﬁ re.

●

When working close to an edge of a

workpiece or at steep angles, or driving

fasteners into thin workpiece use care to

minimize chipping, splitting or splintering, or

free ﬂ ight, ricochet or piercing of fasteners,

which may cause injury.

16

English

●

Never drive nails from both sides of a wall

at the same time. Nails can be driven into

and through the wall and hit a person on the

opposite side.

●

Never use Nailer which is defective or

operating abnormally.

●

Do not use Nailer as hammer.

●

Disconnect air hose from Nailer when:

1) it is not in use;

2) leaving work area;

3) elevating, lowering or otherwise moving it

to another location;

4) handing it to another person;

5) performing any maintenance or repairs;

6) clearing a jam;

7) Nailer is outside of the operator's

supervision or control;

8) removing nails from the magazine;

9) adjusting nailing depth;

10) attaching or removing the nose cap; and

11) turning the top cover.

There are two types of operation to drive nails with this

Nailer.

Use CONTACT ACTUATION MECHANISM or SINGLE

SEQUENTIAL ACTUATION MECHANISM in accordance

with the work to be performed.

Explanation of the various nailing operations

○

CONTACT ACTUATION MECHANISM: First, press

the push lever against the wood; next, pull the trigger

to drive the nail. Or,

pull the trigger; next, press the push lever against the

wood to drive the nail.

If the trigger is held back, a nail will be driven each

time the push lever is pressed against the wood.

NV75AN

•

NV75AN(S1) is shipped with CONTACT

ACTUATION KIT.

When switching from CONTACT ACTUATION KIT

TO SEQUENTIAL ACTUATION KIT, replace to

SEQUENTIAL ACTUATION KIT.

Punch

Contact actuation

trigger kit

Sequential actuation trigger kit

Spiral Pin

○

SINGLE SEQUENTIAL ACTUATION MECHANISM:

First, press the push lever against the wood; next,

pull the trigger to drive the nail.

After nailing once, nailing will not be possible again

until the trigger is released and pressed again.

METHODS OF OPERATION

This Nailer is equipped with the push lever and does

not operate unless the push lever is depressed (upward

position).

There are three methods of operation to drive nails with

this Nailer.

They are:

1. Intermittent operation (Trigger ﬁ re):

CONTACT ACTUATION MECHANISM, SINGLE

SEQUENTAL ACTUATION MECHNISM

2. Continuous operation (Push lever ﬁ re):

CONTACT ACTUATION MECHANISM

3. Single sequential operation (Trigger ﬁ re):

SINGLE SEQUENTIAL ACTUATION MECHANISM

(1) Intermittent operation (Trigger ﬁ re)

WARNING

●

To avoid double ﬁ ring or accidental ﬁ ring due

to recoil.

1) Pull the trigger rapidly and ﬁ rmly.

1

Position the nail outlet on the workpiece with

ﬁ nger oﬀ the trigger.

2

Depress the push lever ﬁ rmly until it is completely

depressed.

3

Pull the trigger to drive a nail.

4

Remove ﬁ nger from the trigger.

To continue nailing in a separate location, move the nailer

along the wood, repeating steps

1

–

4

as required.

Push Lever

2

3

Trigger

17

English

WARNING

●

A nail will ﬁ re each time the trigger is

depressed as long as the push lever remains

depressed.

(2) Continuous operation (Push lever ﬁ re)

Using CONTACT ACTUATION MECHANISM

WARNING

●

To avoid double ﬁ ring or accidental ﬁ ring due

to recoil.

1) Do not press the nailer against the wood with

excessive force.

2) Separate the nailer from the wood as it

recoils after nailing.

1

Pull the trigger with the Nailer oﬀ the workpiece.

2

Depress the push lever against the workpiece to

drive a nail.

3

Move the Nailer along the workpiece with a

bouncing motion.

Each depression of the push lever will drive a nail.

As soon as the desired number of nails have been

driven, remove ﬁ nger from the trigger.

Previously pull

the trigger

1

3

(3) Single sequential operation (Trigger ﬁ re)

WARNING

●

To avoid double ﬁ ring or accidental ﬁ ring due

to recoil.

1) Pull the trigger rapidly and ﬁ rmly.

1

Position the nail outlet on the workpiece with

ﬁ nger oﬀ the trigger.

2

Depress the push lever ﬁ rmly until it is completely

depressed.

3

Pull the trigger to drive a nail.

4

Remove ﬁ nger from the trigger.

To continue nailing in a separate location, move the nailer

along the wood, repeating steps

1

–

4

as required.

Push Lever

2

3

Trigger

WARNING

●

Keep your ﬁ nger oﬀ the trigger except during

fastening operation, because serious injury

could result if the push lever accidentally

contacts you or others in work area.

●

Keep hands and body away from the

discharge area. This Hitachi nailer may

bounce from the recoil of driving a fastener

and unwanted subsequent fastener may be

driven, possibly causing injury.

●

Some types of loaded nails can spark out of

the muzzle during a nail driving operation.

Exercise caution!

The SINGLE SEQUENTIAL ACTUATION MECHANISM

is for use where precision fastener placement is desired.

The SINGLE SEQUENTIAL ACTUATION MECHANISM

may reduce the possibility of bodily injury to you or others

in the work area compared to the CONTACT ACTUATION

MECHANISM. This is because it is less likely to drive

an unwanted nail if you keep the trigger pulled and

accidentally bump the push lever against yourself or

others.

The SINGLE SEQUENTIAL ACTUATION MECHANISM

may also reduce the speed of operation compared

to the CONTACT ACTUATION MECHANISM. The

SINGLE SEQUENTIAL ACTUATION MECHANISM is

recommended to inexperienced users.

18

English

NOTE:

●

If all warnings and instructions are followed,

safe operation is possible with two systems:

CONTACT ACTUATION MECHANISM and SINGLE

SEQUENTIAL ACTUATION MECHANISM.

●

Always handle nails and package carefully. If nails

are dropped, collating wire may be broken.

●

After nailing:

1) disconnect air hose from the Nailer;

2) remove all nails from the Nailer;

3) supply 5 – 10 drops of Hitachi pneumatic tool

lubricant into the air plug on the Nailer; and

4) open the petcock on the air compressor tank to

drain any moisture.

ADJUSTING THE NAILING DEPTH

WARNING

●

Disconnect the air hose from the nailer

before turning the adjuster.

To assure that each nail penetrates to the same depth, be

sure that:

1) the air pressure to the Nailer remains constant

(regulator is installed and working properly), and

2) the Nailer is always held ﬁ rmly against the workpiece.

If nails are driven too deep or shallow into the workpiece,

adjust the nailing in the following order.

1

DISCONNECT AIR HOSE FROM NAILER

Disconnect

air hose

15

Adjuster

Shallow

Deep

2

If nails are driven too deep, turn the adjuster to the

shallow side.

Adjustments are in quarter turn increments.

2

Too Deep

Turn Adjuster

Flush

If nails are driven too shallow, turn the adjuster to the

deep side.

Turn Adjuster

Flush

2

Too Shallow

3

Stop turning the adjuster when a suitable position is

reached for a nailing test.

4

Connect the air hose.

ALWAYS WEAR EYE PROTECTION.

Perform a nailing test.

5

DISCONNECT AIR HOSE FROM NAILER.

6

Choose a suitable position for the adjuster.

CHANGING THE EXHAUST DIRECTION

WARNING

●

When changing the exhaust direction, be

sure to remove your ﬁ nger from the trigger

and disconnect the air hose from the nailer.

The direction of the exhaust vent can be changed by

turning the top cover.

Top Cover

Exhaust Vent

USING THE NOSE CAP (NV75AN, NV75AN(S))

WARNING

●

Disconnect the air hose from the nailer

before attaching or removing the nose cap.

If you would like to be able to move the Nailer more

smoothly across the surface of the workpiece, attach the

nose cap to the push lever.

1

DISCONNECT AIR HOSE FROM NAILER.

2

Put the nose cap to the toe of the push lever.

NOTE:

●

The nose cap may reduce nailing depth due to its

thickness. Re-adjustment of nailing depth is required.

19

English

1

Push Lever

Nose

Hole

Protrusion (Inward)

Do not

connect air

hose

Nose Cap

Nose cap can be removed from the push lever using a

screwdriver or thin rod.

Nose cap

Screwdriver

Push lever

Nose cap can be stored on the magazine as shown below.

Nose cap

Magazine

MAINTENANCE

NOTE: The information contained in this Manual is designed to assist you in the safe maintenance of the Nailer.

Some illustrations in this Manual may show details or attachments that diﬀ er from those on your own Nailer.

MAINTENANCE AND INSPECTION

Read section titled “SAFETY” (pages 4 – 8).

WARNING

●

Disconnect air hose and remove all nails

from Nailer when:

1) doing maintenance and inspection; and

2) clearing a jam.

1. Clearing a jam

Remove a jammed nail in the following order:

1

DISCONNECT AIR HOSE.

2

Open the nail guide.

3

Insert a rod into the outlet.

Tap the rod with a hammer.

Hammer

Rod

Outlet

Disconnect

air hose

1

20

English

3

Open the nail guide and remove dust.

Lubricate the sliding groove of the feeder and

shafts.

Nail Guide

Nail Stopper

Feeder

Feeder Shaft

Feed Piston

4

Lubricate the feeding surfaces of the nose and

the nail guide after cleaning.

This promotes smooth operation and prevents

rust.

CAUTION

●

Check that the nail stopper slides smoothly by

pushing them with ﬁ nger.

If not smooth, nails can be driven at an irregular

angle and hurt someone.

4. Inspecting the magazine

1

DISCONNECT AIR HOSE.

2

Clean the magazine. Remove dust or wooden tips

which may have accumulated in the magazine.

5. Storing

○

When not in use for an extended period, apply a

thin coat of the lubricant to the steel parts to avoid

rust.

○

Do not store the Nailer in a cold weather

environment.

Keep the Nailer in a warm area.

○

When not in use, the Nailer should be stored in a

warm and dry place.

Keep out of reach children.

6. WARNING LABEL

Do not use the Nailer with missing or damaged

WARNING LABEL.

A new WARNING LABEL is available from a Hitachi

authorized service center.

Warning

Label

4

Remove the jammed nail with a slotted screw

driver.

Nail

Slotted Screw Driver

5

Cut the deformed collated wire with nippers.

Correct the deformation.

6

In case of frequent jam, contact a Hitachi

authorized service center.

2. Inspecting the push lever

1

DISCONNECT AIR HOSE.

2

Clean the push lever sliding part.

Lubricate it with Hitachi pneumatic tool lubricant.

Lubricate

Disconnect

air hose

1

3. Inspecting the feeders

1

DISCONNECT AIR HOSE.

2

Clean the knob sliding part.

Lubricate it with Hitachi pneumatic tool lubricant.

Nail

Guide

Knob

Push Lever

Disconnect

air hose

1

La page charge ...

Hitachi NV 75AN Instruction And Safety Manual

Ce manuel convient également à

Hitachi NV 75AN Instruction And Safety Manual

dans d''autres langues

Documents connexes

Autres documents