Haier RDE/RDG 350AW Manuel utilisateur

User Manual and Installation Instructions

Gas & Electric Dryer

User Manual and Installation Instructions

Sèche-linge Genesis

Manual para el usuario e instrucciones

de instalación. Secadora a gas y eléctrica

Model #/ Modéle #/ Para Modelo de #

RDE/RDG 350AW

Quality

n

Innovation

n

Style

(Picture for illustration purposes only. Actual model may vary per model purchased.)

21

English

PAGE

IMPORTANT SAFETY INSTRUCTIONS .......................................2-4

INSTALLATION INSTRUCTIONS ..............................................5-17

Tools and Materials Required ............................................................ 5

Electrical Requirements ..................................................................... 5

Unpacking Your Dryer ..................................................................... 6

Exhaust System Requirements ........................................................... 7

Gas Supply Requirements ................................................................ 9

Location of Your Dryer ...................................................................10

Manufactured (Mobile) Home Instruction .........................................11

Electrical Installation ......................................................................12

3-Wire Cord Connections ..............................................................13

4-Wire Cord Connections ..............................................................14

Gas Connections .......................................................................... 15

Replacement Parts .........................................................................17

OPERATING INSTRUCTIONS ............................................... 18-24

Understanding the Control Panel ......................................................18

Preparations before Drying ............................................................. 19

Load clothes into Dryer ...................................................................20

Auto Dry Cycle .............................................................................. 21

Timed Dry Cycle ............................................................................ 22

Other Features ..............................................................................23

Normal Operating Sounds .............................................................. 24

Tips .............................................................................................. 24

CARE AND CLEANING GUIDE

.......................................................24

TROUBLESHOOTING .................................................................. 25

LIMITED WARRANTY .................................................................26

TABLE OF CONTENTS

21

English

IMPORTANT SAFETY INSTRUCTIONS

Before beginning installation, carefully read these instructions. This will simplify

the installation and ensure the dryer is installed correctly and safely.

NOTE: The electrical service to the dryer must conform with local codes and

ordinances and the latest edition of the National Electrical Code, ANSI/

NFPA 70 or in Canada, CSA C22.1 Canadian Electrical Code Part 1.

NOTE: The gas service to the dryer must conform with local codes and

ordinances and the latest edition of the National Fuel Gas Code, ANSI

Z223.1 or in Canada, CAN/CGA B149.1.

NOTE: The dryer is designed under ANSI Z21.5.1 or ANSI/UL 2158 - CAN/

CSA C22.2 No. 112-97 (latest editions) for HOME USE ONLY. This

dryer is not recommended for commercial application such as restaurants,

beauty salons, etc.

WARNING

For your safety the information in this manual must be

followed to minimize the risk of fire or explosion or to

prevent property damage, personal injury or loss

of life.

Combustible materials, gasoline, and other flammable vapors and

liquids must not be stored near the dryer.

WHAT TO DO IF YOU SMELL GAS

1. Do not try to light any appliance

2. Do not touch any electrical switch. Do not use any phone in

your building.

3. Clear the room, building, or area of all occupants.

4. Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions.

5. If you cannot reach your gas supplier, call the Fire Department.

Installations must be performed by a qualified or licensed

contractor, plumber, or gasfitter qualified or licensed by the state,

province, or region where this appliance is being installed.

English

IMPORTANT SAFETY

INSTRUCTIONS

WARNING - To reduce the risk of fire, electric shock, or

injury to persons when using your appliance, follow the

basic precautions, including the following:

1. Read all of the instructions before using this appliance.

2. Don’t dry articles that have been previously cleaned in, washed in,

soaked in, or spotted with gasoline, dry clean solvents or other

flammable explosive sub stains as they give off vapors which could

ignite or explode.

3. Do not allow children to play on or in the appliance. Close

supervision of children is necessary when the appliance is used near

children.

4. Before the appliance is removed from service or discarded, remove

the door to the drying compartment.

5. Do not reach into the appliance if the drum is moving.

6. Do not install or store this appliance where it will be exposed to

water and/or to the weather.

7. Do not tamper with controls.

8. Do not repair or replace any part of the appliance or attempt any

servicing unless specifically recommended in the user-repair

instructions that you understand and have skills to carry out.

9. Do not use fabric softeners or products to eliminate static unless

recommended by the manufacturers of the fabric softener or

product.

10. Do not use heat to dry articles or products to eliminate static unless

recommended by the manufacturers of the fabric softener or

product.

11. Clean lint screen before or after each load.

12. Keep area around the exhaust opening and adjacent surrounding

areas free from the accumulation of lint, dust and dirt.

13. Keep the dryer area clear and free from items that would obstruct

the flow of combustion and ventilation air through the louvered panel

located on the rear of the dryer.

14. The interior of the appliance and the exhaust duct should be cleaned

periodically by qualified service personnel.

3

English

4

Thank you for using our Haier

product. This easy-to-use manual

will guide you in getting the best

use of your dryer.

Remember to record the model and

serial number. They are on a label

in back of the dryer.

Model number

Serial number

Date of purchase

Staple your receipt to your manual.

You will need it to obtain warranty service.

15. Do not place items exposed to cooking oils in your dryer. Items

contaminated with cooking oil may contribute to a chemical reaction

than could cause a load to catch fire.

16. If material has been used with any flammable liquids or solids, it

should not used in the dryer until all terraces of flammable liquids

and its fumes have been removed.

17. This dryer must be properly installed in accordance with the

installation instructions before it is used. See grounding instructions in

the installations sections.

18. Proper grounding must be ensured to reduce the risk of electric shock

and fire. Check with a qualified electrician or service personnel if you

are in doubt as to whether the dryer is properly grounded.

19. Use the dryer only for its intended purpose: drying clothes.

20. Always disconnect dryer from electrical supply before attempting any

service. Disconnect power cord by grasping the plug, not the cord.

21. Replace worn power cord and/or loose plugs.

22. To reduce the risk of electric shock or fire, do not use extension cords

or adapters to connect dryer electrical power source.

SAVE THESE

INSTRUCTIONS

DANGER

Risk of child entrapment. Before you throw away your old dryer,

take off the door so that children may not get trapped inside.

5

WARNING

Risk of Fire:

1. Clothes dryer installation must be performed by a

qualified installer.

2. Install the clothes dryer according to the manufacturer’s

instructions and local codes.

3. To reduce the risk of severe injury or death, follow all

installation instructions.

SAVE THESE INSTRUCTIONS

Tools and materials required

• Phillips-Head and flathead screwdrivers

• Channel-lock adjustable pilers

• 1/2-inch open-end wrench

• Carpenter’s level

• Measuring tape (12ft. min.)

• Duct tape

• Pipe thread sealer (Gas)

• Rigid or flexible metal 4 inch (102cm) duct

• Vent hood

Safety Warning:

1. Before starting installation, make sure that the gas shut off valve is in the

off position.

2. All old gas connectors and gas piping should be discarded.

ELECTRICAL REQUIREMENTS

Electric Dryer:

(RDE350AW)

C ircuit

Individual 30 Amp branch circuit fused with 30 Amp time-delay fuses or circuit

breakers. Use seperately fused circuits for washers and dryers, and DO NOT

operate a washer and dryer on the same circuit.

P ower Supply

3 or 4 wire, 240 Volt, 1 Phase, 60Hz, AC

(Canada - 240 Volt, 1 Phase, 60 Hz, AC)

P ower Supply Cord Kit

(Not supplied when sold in US. Must be purchased to meet local electrical

codes.) The dryer MUST employ a 3-conductor power supply cord NEMA

10-30 Type SRDT rated at 240 Volt AC minimum, 30 Amp, with 3 open end

INSTALLATION INSTRUCTIONS

English

6

spade lug connectors with upturned ends or closed loop connectors and marked

for use with clothes dryers.

(When sold in Canada - 4-wire power supply cord provided and

attached on dryer)

Dryers being installed in a manufactured (mobile) home MUST employ a

4-wire power supply cord NEMA 14-30 type SRDT or ST (as required) rated

to 240 Volt AC minimum, 30 Amp, with 4 open-end spade lug connectors

with upturned ends or closed loop connectors and marked for use with clothes

dryers. See Electrical Connections for more information on a 4-wire system.

O utlet Receptacle

NEMA 10-30R receptacle should be located so the power supply cord is

accessible when the dryer is in the installed position. (Canada - NEMA 14-30R

receptacle)

ELECTRICAL REQUIREMENTS

Gas Dryer: (RDG350AW)

C ircuit

Individual 15 Amp branch circuit fused with 15-Amp maximum time delay fuse

or circuit breakers.

P ower Supply

3 wire, 120 Volt, 1 Phase, 60Hz, AC

P ower Supply Cord

The dryer is equipped with a 120 Volt 3-wire power supply cord.

Note: This dryer is equipped with a three-prong grounding plug for your

protection against shock hazard and should be plugged into a properly

grounded three-prong receptacle. Do not under any circumstance cut or

remove grounding prong from plug.

Unpacking Your Dryer

1. Remove all packaging material. This includes the foam base and all adhesive

tape holding the dryer accessories inside and outside.

2. Inspect and remove any remains of packaging, tape or printed materials

before using the dryer.

The following are specific requirements for

proper and safe operation of your dryer. Failure

to follow these instructions can create excessive

drying times and fire hazards.

1. Do not use plastic flexible duct to exhaust the dryer. Excessive lint can build up

inside exhaust system and create a fire hazard and restrict air flow. Restricted

air flow will increase drying time. If your present system is made up of plastic

duct or metal foil duct, replace it with a rigid or flexible metal duct. Ensure

present duct is free of any lint prior to installing dryer duct.

2. The dryer must not be exhausted into any gas vent, chimney, wall, ceiling or

any concealed space of a building. The dryer exhaust system MUST be

exhausted to the outdoors. If the dryer is not exhausted outdoors, some

fine lint will be expelled into the laundry area. An accumulation of lint in any

area of the home can create a health and fire hazard.

3. Exceeding the length of duct pipe or number of elbows allowed in the

“Maximum Length” chart can cause an accumulation of lint in the exhaust

system. Plugging the system could create a fire hazard, as well as increase

drying times.

4. Do not screen the exhaust ends of the vent system. Lint can become caught in

the screen, increasing drying time. Use an approved vent hood to terminate the

duct outdoors, and seal all joints with duct tape.

5. All male duct pipe fittings must be installed downstream with the flow of air.

6. Exhaust duct must not be connected or secured with screws or other fastening

devices which extend into the interior of the duct.

7. Do not allow combustible material (clothing, draperies/curtains, paper, etc.) to

come in contact with exhaust system.

Explosion hazard:

Do not install the dryer where gasoline or other flammables are kept or

stored. If the dryer is installed in a garage, it must be a minimum of 18

inches (45.7cm) above the floor. Failure to do so can result in death,

explosion, fire or burns.

Exhaust Requirements:

Use only 4 inch (10.2cm) diameter (minimum) rigid of flexible metal duct and

approved vent hood which has a swing-out damper hat open when the dryer is

in operation. When the dryer stops, the dampers automatically close to prevent

drafts and the entrance of insects and rodents. To avoid restricting the outlet,

WARNING

EXHAUST SYSTEM REQUIREMENTS

English English

7

maintain a minimum of 12 inches (30.5cm) clearance between the vent hood

and the ground or any other obstruction. The vent flap should be able to move

freely, although vertical orientation of the exhaust system is acceptable. Certain

extenuating circumstances could affect the performance of the dryer:

1. Only rigid metal duct work should be used.

2. Venting vertically through a roof may expose the exhaust system to down

drafts causing an increase in vent restriction.

3. Running the exhaust system through an uninsulatedarea may cause

condensation and faster accumulation of lint.

4. Compression of crimping of the exhaust system will cause an increase in

vent restriction.

The exhaust system should be inspected and cleaned a minimum of every 12

months with normal usage. The more the dryer is used the more often you

should check the exhaust system and vent hood for proper operation.

English English

8

RECOMMENDED MAXIMUMM

Exhaust Hood Types

Recommended Use only for short

run installations

No. of 90º

elbows

Rigid Metal Flexible Metal Rigid Metal Flexible

Metal

0 90 ft. 55 ft. 60 ft. 45 ft.

1 60 ft. 40 ft. 45 ft. 30 ft.

2 45 ft. 30 ft. 35 ft. 20 ft.

3 35 ft. 20 ft. 25 ft. 15 ft.

GAS SUPPLY REQUIREMENTS

English English

9

WARNING

Replace copper connecting pipe that is not plastic-

coated. Stainless steel or plastic-coated brass MUST

be used.

1. Installation MUST conform with local codes. In the absence of local codes,

installation must conform with the National Fuel Gas Code, ANSI Z223.1 (latest

edition) or in Canada, the current CAN/CGA B149.1

2. The gas supply line should be 1/2 inch (1.27cm) pipe.

3. If codes allow, flexible metal tubing may be used to connect your dryer to the

gas supply line. The tubing MUST be constructed of stainless steel or plastic-

coated brass.

4. The gas supply line MUST have an individual manual shutoff valve installed

within 6 feet (183cm) of the dryer in accordance with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54.

In Canada, an individual manual shut-off valve MUST be installed in

accordance with the B149.1, Natural Gas and Propane Installation Code.

5. A 1/8 inch (0.32cm) N.P.T. plugged tapping, accessible for test gauge

connection, MUST be installed immediately upstream of the gas supply

connection to the dryer.

6. The dryer MUST be disconnected from the gas supply piping system during

any pressure testing of the gas supply piping system at test pressures in excess

of 1/2 psig (3.45kPa).

7. The dryer MUST be isolated from the gas supply piping system during any

pressure testing of the gas supply piping system at test pressures equal to or

less than 1/2 psig (3.45 kPa).

English English

10

Do Not Install Your Dryer:

1. In an area exposed to dripping water or outside weather conditions.

2. In an area where it will come in contact with curtains, thick carpet, or anything

that will obstruct the flow of combustion and ventilation air.

3. On carpet, floor must be solid with a maximum slope of 1inch (2.54 cm). Any

floor unevenness should be corrected with leveling legs located on the bottom

of the dryer.

Installation in Alcove or Closet:

1. DO NOT install your dryer in a closet with a solid door.

2. A dryer installed in a bedroom, bathroom, alcove or closet MUST be

exhausted outdoors.

3. No other fuel burning appliance shall be installed in the same closet as the

gas dryer.

4. Refer to the images on this page to ensure the installation provides the

minimum amount of clearance required for ventilation.

5. When installing the dryer in a closet with a door, a minimum of 120 square

inches (774.2 square cm) of ventilation in the door is required. Openings must

be equally divided at the top and bottom of the door and airflow must be

unobstructed. A louvered door with equivalent air openings for the length of

the door is acceptable.

LOCATION OF YOUR DRYER

English

1211

1. Dryer MUST be exhausted outside (outdoors, not beneath the manufactured

home) using metal ducting that will not support combustion. Metal ducting must

be 4 inch (10.16 cm) in diameter with no obstructions. Rigid metal duct

is preferred.

2. If dryer is exhausted through the floor and area beneath the manufactured

home is enclosed, the exhaust system MUST terminate outside the enclosure

with the termination securely fastened to the mobile home structure.

3. When installing a gas dryer into a manufactured home, a provision must be

made for outside make up air. This provision is to be not less than twice the

area of the dryer exhaust outlet.

4. This dryer MUST be fastened to the floor using P/N 0030807899

Manufactured Home Installation Kit. Follow the instructions supplied with

the kit.

5. Refer to previous sections for other important venting requirements.

6. Installation must conform to current Manufactured Home Construction & Safety

Standard (which is a Federal Regulation Title 24 CFR-Part 32-80) or when

such standard is not applicable, with American National Standard for Mobile

Homes. In Canada, the CSA Z240 is applicable.

MANUFACTURED (MOBILE) HOME INSTALLATION

English

1211

The following are specific requirements for proper

and safe electrical installation of your dryer.

Failure to follow these instructions can create

electrical shock and/or fire hazard.

WARNING

1.

This appliance must be properly grounded. Electrical shock can result if the

dryer is not properly grounded. Follow the instructions in this manual for

proper grounding.

2.

Do not use an extension cord with this dryer. Some extension cords are not

designed to withstand the amounts of electrical current this dryer utilizes and

can melt, creating electric shock and/or fire hazard. Locate the dryer within

reach of the receptacle for the length power cord to be purchased, allowing

some slack in the cord. Refer to the electrical requirements in this manual for

the proper power cord to be purchased.

3. A UL approved strain relief must be installed onto power cord. If the strain

relief is not attached, the cord can be pulled out of the dryer and can be cut

by any movement of the cord, resulting in electrical shock.

4. Do not use an aluminum wire receptacle with copper-wired power cord and

plug (or vice versa ). A chemical reaction occurs between copper and

aluminum and can cause electrical shorts. The proper wiring and receptacle

is a copper-wired power cord with a copper-wired receptacle.

Note: Dryers operating on 208 Volt power supply sill have longer drying times

than operation on 240 Volt power supply.

WARNING

Improper connection of the equipment grounding conductor can

result in a risk of electrical shock. Check with a licensed

electrician if you are in doubt as to whether the appliance is

properly grounded.

1. Gas dryers are equipped with a factory installed three-prong 15 Amps ~120

Volts (grounding) plug for your protection against shock hazard and should be

plugged directly into a properly grounded three-prong receptacle. Do not cut

or remove the grounding prong from this plug.

ELECTRICAL INSTALLATION

ELECTRIC Dryer (RDE350AW)

GAS Dryer (RDG350AW)

Brass Terminal

Nut

Tighten Nut to

These Threads

Power Cord

Strain Relief

Mounting Bracket

Green Ground

Screw

Neutral

Ground Wire

English

13

3-Wire Cord Connection (US models only)

1. Remove the screws securing the terminal block access cover and the strain

relief mounting bracket located on the back of the dryer’s upper corner.

2.

Install a U.L. approved strain relief into the power cord entry hole of the

mounting bracket. Finger tighten the nut only at this time.

3. Thread a U.L. Approved 30 Amp. Power cord, NEMA 10-30 Type SRDT,

through the strain relief.

4. Attach the power cord neutral (center wire) conductor to the brass colored

center terminal on the terminal block. Tighten the screw securely.

5. Attach the remaining two power cord outer conductors to the outer brass

colored terminals on the terminal block. Tighten both screws securely.

Warning: Do not make a sharp bend or crimp wiring/conductor at

connections.

6. Reattach the strain relief mounting bracket to the back of the dryer with two

screws. Tighten screws securely.

7. Tighten the screws securing the cord restraint firmly against the power cord.

8. Tighten the strain relief nut securely so that the strain relief does not turn.

9. Reinstall the terminal block cover.

ELECTRICAL CONNECTIONS

ELECTRIC Dryer (RDE350AW)

Terminal Block

English

4-Wire Cord Connections (US Models Only)

1. Remove the screws securing the terminal block access cover and the strain

relief mounting bracket located on the back of the dryer upper corner.

2. Install a UL approved strain relief into the power cord entry hole of the

mounting bracket . Finger tighten the nut only at this time.

3. Remove the green neutral ground wire from the green ground screw located

above the terminal block.

Brass Terminal

Red

Tighten Nut to

These Threads

Power Cord

Strain Relief

Mounting Bracket

Green Ground

Screw

Neutral

Ground Wire

Terminal Block

Black

Nut

Green Power Cord

Ground Wire

Black 240V

White Neutral

Red 240V

Green Ground

Typical Conductor

Receptacle

Typical 4

Conductor Cord

ELECTRIC Dryer (RDE350AW)

14

White

English

15

4. Thread a U.L. approved 30 Amp power cord. NEMA 14-30 type ST or SRDT

through the strain relief.

5. Attach the green power cord ground wire to the cabinet with green ground

screw.

6. Attach the white (neutral) power cord conductors to the outer cord and the

green ground wire from the dryer harness to the brass-colored center

terminal on the terminal block. Tighten the screw securely.

7. Attach the red and black power cord conductors to the outer brass-colored

terminals on the terminal block.

Warning: Do not make a sharp bend or crimp the wiring /conductor at

connections.

8. Tighten the screws securing the cord restraint firmly against the power cord.

9. Tighten the strain relief nut securely so that the strain relief does not turn.

10. Reinstall the terminal block cover.

NOTE: DO NOT connect the dryer to L.P. gas service without

converting the gas valve. An L.P. Conversion Kit must be

installed by a qualified gas technician.

1. Remove the shipping cap from gas pipe at the rear of the dryer.

2. Connect a 1/2 inch (1.27cm) I.D. semi-rigid or approved pipe from gas supply line to

the 3/8 inch (0.96cm) pipe located on the back of the dryer. Use a 1/2 inch to 3/8

inch (1.27cm to 0.96cm) reducer for a connection. Apply an approved thread sealer

that is resistant to the corrosive action of liquified gases on all pipe connections.

3. Open the shutoff valve in the gas supply line.

4. Test all connections by brushing on a soapy water solution. NEVER TEST FOR GAS

LEAKS WITH AN OPEN FLAME.

5. Connect the exhaust duct to the outside exhaust system. Use duct tape to seal all joints.

6. With the dryer in its final position, adjust one or more of the legs until the dryer is resting

solid on all four legs. Place a level on top of the dryer. THE DRYER MUST BE LEVEL

AND RESTING SOLID ON ALL FOUR LEGS.

7. Plug the power cord into a grounded outlet. NOTE: check to ensure power is OFF at

circuit breaker/fuse box before plugging the power cord into the outlet.

8. Turn on the power at the circuit breaker/fuse box.

WARNING

Before operating the dryer, make sure the dryer area is clean and free

from combustible materials, gasoline, and other flammable vapors. Also

see that nothing (such as boxes, clothing, etc.) obstructs the flow of

combustion and ventilation air through the louvered panel located on the

rear of the dryer.

9. Run the dryer through a cycle check for proper operation.

NOTE: On gas dryers, before the burner will light, it is necessary for the gas line to

be bled of air. If the burner does not light within 45 seconds the first time

the dryer is turned on, the safety switch will shut the burner off. If this

happens, turn the dryer to “OFF” and wait 5 minutes before making

another attempt to light.

NOTE: Follow instructons supplied with kit.

GAS CONNECTIONS

GAS Dryer (RDG350A)

English

16

A) Connect female 3/8” NPT elbow to gas

inlet on dryer. Then connect 3/8” flare

union adapter to female elbow.

IMPORTANT: To prevent the inlet from

twisting, please use a pipe

wrench to secure the dryer

gas inlet. Affix Teflon®

tape or pipe compound to

adapter and gas inlet.

B) Attach the flexible metal gas line connector

to the adapter.

C) Make sure flexible gas line seal is secure.

Use two wrenches for the best possible

connection.

D) To check gas inlet pressure, attach 1/8”

NPT plugged tapping to dryer gas line shut-

off valve. Then connect flare union adapter

to plugged tapping. Affix Teflon® tape

to the threads of the adapter and plugged

tapping to ensure seal.

E) Use two adjustable wrenches to tighten

every connection.

IMPORTANT: Do not overtighten!

F) Open gas shut-off valve.

CONNECTING THE DRYER TO THE GAS SUPPLY

English English

17

REPLACEMENT PARTS

Replacement parts and accessories for US and Canada can be purchased

through Haier America at 1-800-313-8495

WARNING

Label all wires prior to disconnection when servicing controls.

Wiring errors can cause improper and dangerous operation. Check

unit for proper operation after servicing.

WARNING

Discard or destroy the carton and plastic bags after the dryer is

unpacked. Children should not be allowed to use them to play with.

Cartons covered in rugs, bedspreads or plastic sheets can become

an airtight chamber and cause suffocation leading to death. Make

all packing materials inaccessible to children.

WARNING

The instructions in this manual and all other literature included with

this dryer can not cover every possible condition and situation that

may occur. Good safe practice and caution must be applied when

installing, operating, and maintaining any appliance. If you are in

doubt after installing, call a certified electrician to install and wire

the dryer.

English

English English

OPERATING INSTRUCTIONS

English

18

RDE/RDG 350AW

Understanding the Control Panel

1 2 3 4

Note: Features may vary per model.

Temp Button: (1)

• Used to set drying temperatures. There are four available drying temperatures to

choose from: High, Medium, Low, and Air Fluff.

Cycle Select Dial: (2)

• Select the from 3 Auto-Dry cycles (Heavy Duty, Normal, and Delicates), or

4 Time Dry Cycles (30,60,90 or 120 minutes)

Start/Pause Button (3)

• Push to start after selecting the dry cycle and setting the temperature. Push once

to pause. Push again to start after pushing.

Cycle Progress: (4)

• This indicates the process the cycle is currently in. At the end of the dry cycle

the dryer will automatically go in the wrinkle saves mode. Here the dryer tub

will tumble periodically for 1 hour after the dry cycle is completed. To stop

simply open the door and remove the clothes.

Heavy Duty Heavyweight material such as jeans or bath towels.

Normal Normal drying

Delicate Drying small quantity clothes and delicate fabric.

English

2019

• Sort clothes of the same kind (cotton, synthetics, woolen) to dry.

• Dark and light colored clothes should be separately dried. Fabrics prone to

losing lint and those prone to adhering lint shall be separately dried. Clothes

prone to falling lint should be turned inside out before putting into the dryer.

• Make sure buttons and ornaments on the clothes are high temperature

resistant and won’t damage drum surface. Before loading, the clothes should

have their zippers zipped up, buttons and hooks done up and belts tied so as to

avoid entanglement or other obstacles.

• If possible, turn out the clothes pockets for uniform drying.

• Check if clothes remain soiled. If so, wash them again, otherwise soils may be

permanently set.

• Small articles should be collected in a mesh bag before loading and drying, so

as to avoid entanglement and ensure easy removal.

• Make sure the power socket is reliably grounded. The grounding terminal should

not be connected to gas or tap water pipelines.

• Make sure exhaust duct has been properly connected.

• Make sure lint filter is clean and properly installed. If lint filter is not in place,

tumbling items could enter the exhaust system and cause damage to the dryer.

Note: Applies to Auto Dry cycle and Timed Dry cycle.

PREPARATIONS BEFORE DRYING

La page charge ...

Haier RDE/RDG 350AW Manuel utilisateur

Haier RDE/RDG 350AW Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents