SINGER EM200 Sewing Machine Manuel utilisateur

INSTRUCTION MANUAL

EM200

2

This household embroidery machine is designed to comply with IEC/EN 60335-2-28 and UL

1594.

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be followed,

including the following:

Read all instructions before using this household embroidery machine. Keep these instructions

conveniently near the machine. Make sure to hand them over if the machine is given to a third

party.

DANGER

To reduce the risk of electric shock:

An embroidery machine should never be left unattended when plugged in. Always unplug

this embroidery machine from the electric outlet immediately after using and before cleaning,

removing covers or when making any other user servicing adjustments mentioned in the

instruction manual.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of burns, ﬁ re, electric shock, or injury to persons:

• Do not allow to be used as a toy. Close attention is necessary when this embroidery machine

is used by or near children.

• Use this embroidery machine only for its intended use as described in this manual. Use only

attachments recommended by the manufacturer as contained in this manual.

• Never operate this embroidery machine if it has a damaged cord or plug, if it is not working

properly, if it has been dropped or damaged, or dropped into water. Return the embroidery

machine to the nearest authorized service center for examination, repair, electrical or

mechanical adjustment.

• Never operate the embroidery machine with any air openings blocked. Keep ventilation

openings of the embroidery machine free from the accumulation of lint, dust, and loose fabric.

• Keep ﬁ ngers away from all moving parts. Special care is required around the embroidery

machine needle.

• Always use the proper needle plate. The wrong plate can cause the needle to break.

• Do not use bent needles.

• Do not pull or push fabric while stitching. It may deﬂ ect the needle causing it to break.

• Wear safety glasses.

• Switch the embroidery machine off (“0”) when making any adjustment in the needle area,

such as threading needle, changing needle, threading bobbin, changing presser foot, etc.

• Never drop or insert any object into any opening.

• Do not use outdoors.

• Do not operate where aerosol (spray) products are being used or where oxygen is being

administered.

• To disconnect, turn all controls to the off (“0”) position, then remove plug from outlet.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not use the machine if it is wet.

• If the LED lamp is damaged or broken, it must be replaced by the manufacturer or its service

agent or a similarly qualiﬁ ed person, in order to avoid a hazard.

3

SINGER® is the exclusive trademark of The SINGER® Company Limited S.à.r.l. or its Afﬁ liates.

PREFACE

Thank you for your purchase of this embroidery machine.

This machine intended for household use will provide you with excellent performance in sewing

embroidery designs and lettering.

Please refer to this booklet for proper use and optimum performance. To get the most out of

your embroidery machine, read the entire instruction manual before attempting to operate the

machine. Then familiarize yourself with the machine by following the instruction manual page by

page.

To ensure that you are always provided with the most modern embroidery capabilities, the

manufacturer reserves the right to change the appearance, design or accessories of this

embroidery machine when considered necessary without notiﬁ cation or obligation.

FOR EUROPE ONLY:

This appliance can be used by children aged from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in a safe way and understand

the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance

shall not be made by children without supervision.

The noise level under normal operating conditions is less than 70db.

FOR OUTSIDE EUROPE:

This embroidery machine is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the embroidery machine by a person

responsible for their safety. Children should be supervised to ensure that they do not play with

the embroidery machine.

The noise level under normal operating conditions is less than 70db.

SERVICING OF DOUBLE INSULATED PRODUCTS

In a double-insulated product, two systems of insulation are provided instead of grounding. No

ground means is provided on a double-insulated product, nor should a means for grounding

be added to the product. Servicing of a double-insulated product requires extreme care and

knowledge of the system and should be done only by qualiﬁ ed service personnel. Replacement

parts for a double-insulated product must be identical to those parts in the product. A double-

insulated product is marked with the words ‘DOUBLE INSULATION’ or ‘DOUBLE INSULATED’.

SETTING UP THE MACHINETHREADING THE MACHINE

EMBROIDERY PREPARATION

EMBROIDERYMAINTENANCE

• This embroidery machine is provided with double insulation. Use only identical replacement

parts. See instructions for Servicing of Double-Insulated Appliances.

SAVE THESE INSTRUCTIONS

Servicing should be performed by an authorized service representative.

4

MAIN PARTS

........................................................................5

ACCESSORIES

....................................................................6

NEEDLES

..............................................................................7

REMOVING & INSERTING THE NEEDLE ...........................7

SELECTING NEEDLE & THREAD ........................................7

SETTING UP THE MACHINE

...............................................8

CONNECTING THE EMBROIDERY UNIT ............................8

REMOVING THE EMBROIDERY UNIT ................................8

ELECTRICAL CONNECTION ...............................................8

MESSAGES AT START UP ...................................................9

MACHINE CONTROL FUNCTIONS .....................................9

START/STOP BUTTON ..................................................9

SPEED CONTROL BUTTONS .......................................9

THREAD CUTTER BUTTON .........................................10

TOP COVER ..................................................................10

HAND WHEEL ...............................................................10

PRESSER FOOT LIFTER .............................................10

THREAD CUTTER ........................................................10

MOUNTING MACHINE IN SEWING CABINET .............10

SOFTWARE INFORMATION

.............................................. 11

USB EMBROIDERY STICK ................................................ 11

CONNECTING USB STICK ........................................... 11

DESIGN BOOK .............................................................. 11

INDIVIDUAL DESIGN INFORMATION .......................... 11

EMBROIDERY SOFTWARE .......................................... 11

UPDATING YOUR MACHINE ........................................ 11

THREADING THE MACHINE

............................................. 12

BOBBIN SETTING ..............................................................12

REMOVING THE BOBBIN.............................................12

SETTING SPOOL OF THREAD ON SPOOL PIN ..........12

WINDING THE BOBBIN ................................................12

WINDING BOBBIN INDEPENDENTLY .........................13

INSERTING THE BOBBIN .............................................13

THREADING THE NEEDLE ................................................14

PREPARING TO THREAD MACHINE ...........................14

SETTING SPOOL OF THREAD ON SPOOL PIN ..........14

THREADING THE UPPER THREAD ............................14

THREADING THE NEEDLE EYE ..................................15

DRAWING UP THE BOBBIN THREAD .........................15

EMBROIDERY PREPARATION

..........................................16

HOME SCREEN/HOME BUTTON ......................................16

EMBROIDERY MACHINE SETTINGS ................................16

SETTING BUTTON ........................................................16

THREAD TENSION .......................................................16

STOP FOR CUT ............................................................17

AUDIBLE BEEP .............................................................17

CONTRAST OF SCREEN .............................................17

CALIBRATION SCREEN ...............................................17

SOFTWARE VERSION .................................................17

USING FABRIC AND STABILIZER .....................................18

SECURING FABRIC IN THE EMBROIDERY HOOP ..........19

ATTACHING THE EMBROIDERY HOOP TO THE MACHINE .

19

REMOVING THE HOOP FROM THE MACHINE ..........19

SELECTING DESIGNS

.......................................................20

HOME SCREEN ..................................................................20

EMBROIDERY COLLECTION .......................................20

SELECTING A DESIGN ......................................................20

TO SELECT A BUILT-IN DESIGN ..................................20

TO SELECT A USB DESIGN .........................................20

EDITING THE DESIGN

.......................................................21

EMBROIDERY PLACEMENT SCREEN..............................21

EMBROIDERY ROTATION AND MIRRORING SCREEN ...21

EMBROIDERY SCALING SCREEN ....................................21

EMBROIDERY OPTION SCREEN ......................................22

HOOP OPTION AND SELECTION ................................22

HOOP OPTION - MOVING HOOP POSITION ..............22

HOOP SELECTION .......................................................22

TRACING .......................................................................23

BASTING .......................................................................23

MONOCHROME ............................................................23

SEWING DESIGN

............................................................... 24

SEWING SCREEN ..............................................................24

START TO SEW ..................................................................24

EMBROIDERY LETTERS

...................................................25

SELECTING EMBROIDERY LETTERS ..............................25

EDITING EMBROIDERY LETTERS ....................................25

SEWING EMBROIDERY LETTERS ....................................25

POP-UP MESSAGES

.........................................................26

UPPER THREAD BREAKAGE .....................................26

CONNECT USB ............................................................26

THREAD JAM ................................................................26

WRONG HOOP TYPE ...................................................26

DATA ON THE USB STICK CANNOT BE READ...........26

REMOVE THE HOOP ....................................................26

EMBROIDERY TOO LARGE .........................................26

STOP COMMAND IN DESIGN ......................................26

MAIN MOTOR OVERLOAD ...........................................26

CORRUPTED DATA ......................................................26

MAINTENANCE

..................................................................27

REMOVING THE EMBROIDERY FOOT .............................27

ATTACHING THE EMBROIDERY FOOT ......................27

CLEANING .......................................................................... 27

BOBBIN HOLDER .........................................................27

HOOK RACE & FEED DOG ..........................................27

HELPFUL HINTS

................................................................ 28

EMBROIDERY QUICK REFERENCE CHART

...................29

TECHNICAL SPECIFICATION

...........................................30

DESIGN BOOK

TABLE OF CONTENTS

5

19. Needle Clamp Screw

20. Needle Thread Guide

21. Needle

22. Bobbin Cover

23. Bobbin Cover Latch

1. Face Plate

2. Top Cover

3. Thread Take-Up Lever

(Inside)

4. Presser Foot Lifter

5. Touch Panel LCD

6. Home Button

1 2 3 4 5 6

9

7 8

10 11 12

13

14

15

19

16

17

18

20

21

22

23

24 25 26 27 28 29 30 31

32 33 34

MAIN PARTS

7. Setting Button

8. Hand Wheel

9. Start/Stop Button

10. Slow Button

11. Fast Button

12. Thread Cutter Button

13. Thread Cutter

14. Needle Threader

15. Needle Threader Lever

16. Presser Foot Screw

17. Embroidery Presser Foot

18. Needle Plate

24. Auxiliary Spool Pin

Holder

25. Thread Guide

26. Extra Thread Guide

27. Bobbin Winding Tension

Disc

28. Spool Pin

29. Bobbin Winder Stop

30. Bobbin Winder Shaft

31. Bobbin Winder Thread

Cutter

32. USB Embroidery

Stick Socket

33. Power Switch

34. Connector for

Power Cord

35. Handle

35 36

36. Embroidery Unit Connection Socket

37 39 40 41 42

37. Accessory Tray

38. Embroidery Unit

Release Lever (Under

Accessory Tray)

39. Level Adjusting Feet

(Bottom of Unit)

40. Embroidery Hoop

Carriage

41. Embroidery Hoop

Connection Assembly

42. Embroidery Unit

Socket

38

SETTING UP THE MACHINE

6

ACCESSORIES

Some accessories are stored in the accessory tray.

1. Needle Pack

2. 5 SINGER® Class 15 transparent bobbins

( 1 is in the machine)

3. Seam Ripper

4. Brush

5. Screw Driver

6. Thread Net

7. Auxiliary Spool Pin

8. 2 Felt Washers

9. Screwdriver for Needle Plate

10. Spool Cap

11. Small Thread Cap

12. USB Embroidery Stick

13. Power Line Cord

14. Embroidery Hoop 100mm x 100mm (4” x 4”)

15. Embroidery Hoop 260mm x 150mm (10 1/4” x 6”)

1 2 3

4

5 6 7

8 9 10 11 12

13

14

15

ACCESSORIES

ACCESSORY TRAY

The accessory tray is located on the left side of the embroidery

unit. Pull to open.

7

REMOVING & INSERTING THE NEEDLE

Select a needle of the appropriate style and size for the fabric

to be embroidered.

CAUTION

To prevent accidents:

Turn off the power before removing the needle.

1. Turn the hand wheel toward you until the needle is at its

highest position.

2. Loosen the needle clamp screw.

SELECTING NEEDLE AND THREAD

For good quality results, it is important to use the appropriate

style and size of needle for the fabric that will be embroidered.

For help with determining which needle to use, refer to the

Embroidery Quick Reference Chart on page 29.

NEEDLE

1. For light weight woven fabrics, use SINGER® Style 2000,

Size 11/80 needle.

2. For medium to heavier weight woven fabrics, use SINGER®

Style 2000, Size 14/90 needle.

3. For light weight stretch fabrics, use SINGER® Style 2001,

Size 11/80 needle.

4. For medium to heavier weight stretch fabrics, use

SINGER® Style 2001, Size 14/90 needle.

It is possible to substitute SINGER® Style 2020 needles for

the 2000 Style, in either the 11/80 or 14/90 sizes.

It is possible to substitute SINGER® Style 2045 needles for

the 2001 Style, in either the 11/80 or 14/90 sizes.

It is recommended to use SINGER® needles in your SINGER®

embroidery machine.

THREAD

Machine embroidery is most often done using rayon or

polyester thread in the needle.

A lighter weight thread, referred to as bobbinﬁ ll, is

recommended for the bobbin. This helps create less density on

the back side of the embroidery design.

NOTE: In addition to the correct needle and thread, it is also

important to use the appropriate stabilizer for the fabric to be

embroidered. (See pages 18 and 29 for more information.)

3. Remove the needle.

4. Insert new needle into needle clamp with the ﬂ at side to the

back and push it up as far as it will go.

5. Tighten the needle clamp screw securely.

Do not use a bent or blunt needle (a). Place needle on a

ﬂ at surface to check its straightness.

NEEDLES

SETTING UP THE MACHINE

8

CONNECTING THE EMBROIDERY UNIT

There is a covered socket (A) behind the machine. The cover

will open automatically when connecting the embroidery unit.

1. Turn the machine off before connecting the embroidery unit.

2. Slide the embroidery unit onto the arm of the machine until

it plugs ﬁ rmly into the socket.

3. If needed, use the level adjusting feet so that the machine

and embroidery unit are even with one another.

ELECTRICAL CONNECTION

DANGER

To reduce the risk of electric shock:

Never leave unattended when plugged in. Always

unplug this machine from the electric outlet

immediately after using and before maintenance.

WARNING

To reduce the risk of burns, ﬁ re, electric shock, or

injury to persons:

Do not unplug by pulling on cord. To unplug, grasp

the plug, not the cord.

1. Place machine on stable surface.

2. Connect the power line cord to the machine by inserting

the 2-hole plug into the power cord connector.

SETTING UP THE MACHINE

TO REMOVE THE EMBROIDERY UNIT

Remove the hoop from the machine. (See Page 19)

1. To store the embroidery unit into the box, move the carriage

to park position by selecting Park Position in the Hoop

Option. (See page 22)

2. Turn off the machine.

3. Pull the lever (B) at the left, underneath the embroidery unit

and slide the unit to the left to remove it.

The cover of the socket closes automatically.

4. Store the embroidery unit in the original packing material.

3. Connect the power line plug to the electric outlet.

4. Turn on the power switch.

5. The lamps will light up when switch is turned on (symbol I).

6. To disconnect, turn the power switch to the off position (symbol

O), then remove plug from outlet.

FOR UNITED STATES AND CANADA USERS:

POLARIZED PLUG INFORMATION

This appliance has a polarized plug (one blade wider than the

other). To reduce the risk of electric shock, this plug is intended

to ﬁ t in a polarized outlet only one way. If the plug does not ﬁ t

fully in the outlet, reverse the plug. If it still does not ﬁ t, contact

a qualiﬁ ed electrician to install the proper outlet. Do not modify

the plug in any way.

9

MESSAGES AT START UP

When you turn the machine on, a series of messages will

appear on the screen.

a. If the embroidery unit is not attached, this message will

appear. Attach the unit correctly. (See previous page.)

b. If the needle is not in its highest position, this message

will appear. Turn the hand wheel toward you to raise the

needle to its highest position and then press the “

✓

” button.

MACHINE CONTROL FUNCTIONS

S

TART/STOP BUTTON (A)

The machine will start running when Start/Stop button is

pressed and will stop when pressed the second time. The

machine will ramp up slowly at start of sewing.

NOTE:

1. Machine will not start if you don’t select an embroidery

design or letter.

2. Bobbin winding function is independent from this button. (See

page 12)

SPEED CONTROL BUTTONS (B)

The sewing speed is controlled by the machine.

You can change the maximum speed by pressing these

buttons.

Press the left button to decrease the speed.

Press the right button to increase the speed.

NOTE:

If you use a specialty thread, such as metallic thread, you

should reduce the the maximum speed to help prevent thread

breakage.

A B

SETTING UP THE MACHINE

c. If this message appears, remove the hoop (if attached),

clear the embroidery area and press the “

✓

” button.

d. If presser foot is lowered, this message will appear. Raise

the presser foot lifter and press the “

✓

” button.

(See next page)

When the messages a-d have cleared the screen, the carriage

will move to start point.

e. The Home Screen will appear.

(For more information on the Home Screen, see page 16.)

CAUTION

To prevent accidents:

1. Do not carry the machine when embroidery unit is

attached. It may fall off.

2. Do not push nor pull the carriage forcefully. It may

break.

3. Do not hold the carriage to move the machine.

4. Do not press the screen too hard and do not use

sharp objects to touch it. Doing so can damage the

screen. Touch the screen with your ﬁ nger only.

SETTING UP THE MACHINE

10

THREAD CUTTER BUTTON (C)

By pressing this button, machine will cut both threads

automatically.

NOTE:

The machine will cut threads automatically between color

changes and when an embroidery design has been completed.

CAUTION:

1. Do not press this button when there is no fabric under the

presser foot or no need to cut the threads. The thread may

tangle, resulting in damage.

2. Do not use this button when cutting thread thicker than

#30, nylon thread or other speciality threads.

In this case, use the thread cutter (G).

C

FG

H

D

E

SETTING UP THE MACHINE

TOP COVER (D)

To open the top cover, lift up the front right side of the cover.

HAND WHEEL (E)

By turning the hand wheel, the needle will raise or lower. You

should always turn hand wheel toward you.

PRESSER FOOT LIFTER (F)

The presser foot is raised or lowered by this lever.

You can raise and hold the presser foot lifter to an extra-high

position, which can help make it easier to install the embroidery

hoop.

NOTE:

Machine will not start when the presser foot is raised (except

for bobbin winding).

THREAD CUTTER (G)

Use this cutter if the Thread Cutter button is not used.

1. Raise the presser foot and bring threads toward the back.

2. Hook the threads to the thread cutter from back to front.

3. Pull threads to cut them.

MOUNTING MACHINE IN SEWING CABINET (H)

There are two holes on the underside of the machine designed

for mounting the machine into a sewing cabinet. Align the

holes (indicated in the picture) with the corresponding holes in

the cabinet base. Attach the machine with screws. (Screws not

included)

11

USB EMBROIDERY STICK

Your machine comes with a USB stick. This stick contains the

following:

a. Design Data (embroidery designs)

b. Design Book (PDF ﬁ le displaying images of included

embroidery designs and fonts, viewed on PC)

c. Individual Design Information (PDF ﬁ le displaying details

on individual designs, viewed on PC)

CONNECTING USB STICK

Your machine has a USB socket to read embroidery data from

the USB embroidery stick.

Open the cover and insert the USB embroidery stick in the

socket. The USB plug can only be inserted one way - do not

force it into the socket.

To remove, carefully pull the USB embroidery stick out straight.

NOTE:

Do not remove the USB embroidery stick while operating the

machine or stitching the embroidery, as this can damage the

ﬁ les on your USB embroidery stick.

DESIGN BOOK

A Design Book is provided, which displays an overview of the

included embroidery designs and fonts that come with your

machine. You can see an images of the designs, as well as

the dimensions and stitch count of the designs.

This book is a PDF ﬁ le, which can be accessed from the USB

stick when placed in your PC. Your PC will need to have

Adobe Acrobat Reader installed in order to view the Design

Book. If your PC doesn’t have Acrobat Reader, access the

Adobe website to install it.

INDIVIDUAL DESIGN INFORMATION

This is a PDF ﬁ le that contains more speciﬁ c information

about each individual embroidery design that comes with your

machine, such as the order of thread colors, suggested thread

colors and more.

This book is a PDF ﬁ le, which can be accessed from the USB

stick when placed in your PC. Your PC will need to have

Adobe Acrobat Reader installed in order to view the Design

Book. If your PC doesn’t have Acrobat Reader, access the

Adobe website to install it.

EMBROIDERY SOFTWARE

Embroidery software is available for your machine, which will

allow you to use designs from other sources, such as design

CD’s and designs from the internet.

Go to singer.mysewnet.com for information on how to

download this software to your PC.

UPDATING YOUR MACHINE

Periodically, updates may be made available for your machine.

Your machine is updated via your USB stick.

1. Go to singer.mysewnet.com for information about available

updates for your machine.

2. Follow the instructions for how to update your machine.

SOFTWARE INFORMATION

SETTING UP THE MACHINE

12

BOBBIN SETTING

Be sure to use only SINGER® Class 15 transparent bobbins in

this machine.

REMOVING THE BOBBIN

1. Pull the bobbin cover latch to the right and remove the

bobbin cover.

2. Lift up the bobbin from the machine.

THREADING THE MACHINE

SETTING SPOOL OF THREAD ON SPOOL PIN

1. Pull up the left end of spool pin and set the felt washer and

the spool of thread on spool pin so that the thread unrolls

from the front of the spool.

2. Set the spool cap on spool pin as far as it will go.

a. The spool cap can be reversed in order to better

accommodate the size of smaller thread spools.

b. Use the small spool cap when you use cross wound

thread. Leave small opening between cap and spool as

illustrated.

c. Set the thread net over the spool if thread unrolls too

easily.

WINDING THE BOBBIN

1. Hold thread in both hands and hook thread to the guide

from front opening.

2. Bring thread to the right and pass it through the thread

guide from the back side. Pass thread under the tension

disc in a clockwise direction.

3. Insert thread through hole in bobbin and place the bobbin

on bobbin winder spindle.

4. Hold the end of the thread and push bobbin stopper to the

right. When the bobbin winding screen appears, press the

Start/Stop button on the screen to start winding.

5. After the bobbin winds a few turns, stop the machine by

pressing the Start/Stop button on the screen.

6. Cut the thread near the hole, as illustrated.

7. Start the machine again.

You can adjust winding speed by pressing “+” (faster) or “-”

(slower) button on the screen.

8. When the bobbin is wound fully, the bobbin stopper will

return to the left and stop winding.

9. Remove the bobbin from the spindle and cut thread with

the thread cutter.

13

INSERTING THE BOBBIN

1. Place bobbin into bobbin holder, making sure the bobbin

turns in a counter clockwise direction.

WINDING BOBBIN INDEPENDENTLY

You can wind the bobbin independently while embroidery

stitching.

1. Insert the auxiliary spool pin into the hole at the left side on

the top of the machine.

2. Place the felt washer and spool of thread onto the auxiliary

spool pin.

3. Bring thread to the right and hook the thread to the thread

guide from rear opening.

4. Follow the normal winding procedure from Steps 2 to 9 (on

page 12).

a

THREADING THE MACHINE

2. Draw thread into notch (a) while holding the bobbin.

3. Pull thread along the groove, up and around the top, to the

left, then down.

While lightly holding the bobbin in place with your ﬁ nger,

pull the thread to the right to cut the thread.

4. Replace the bobbin cover. Set the left tabs into the holes in

needle plate and push the right side of bobbin cover down

until it clicks into place.

NOTE:

This machine can start to sew without manually drawing up the

bobbin thread.

If you want to draw up the bobbin thread manually, see page

15.

Be sure to use only SINGER® Class 15 transparent bobbins in

this machine.

THREADING THE MACHINE

14

THREADING THE NEEDLE

P

REPARING TO THREAD MACHINE

1. RAISE THE PRESSER FOOT LIFTER. It is very important

to raise the presser foot lifter before you proceed to thread

the machine to ensure proper thread tension.

2. Raise the needle to its highest position by turning the

handwheel toward you.

(Keep this position for threading the eye of the needle.)

NOTE:

It is very important to raise the presser foot lifter before you

thread the machine. Not doing so will likely result in poor

stitch quality, or excessive thread loops on the underside of

the fabric. Always raise the presser foot lifter before you begin

threading the machine.

THREADING THE MACHINE

SETTING SPOOL OF THREAD ON SPOOL PIN

1. Pull up the left end of spool pin and set the felt washer and

the spool of thread on spool pin so that the thread unrolls

from the front of the spool.

2.

Set the spool cap on spool pin as far as it will go.

a. The spool cap can be reversed in order to better

accommodate the size of smaller thread spools.

b. Use the small spool cap when you use cross wound

thread. Leave small opening between cap and spool as

illustrated.

c. Set the thread net over the spool if thread unrolls too

easily.

THREADING THE UPPER THREAD

1. Hold thread in both hands and pass thread into the guide

from front opening.

2. Bring thread backward and pass through the slit from right

to left.

3. Bring thread to the left and pull thread down toward you

along the slit.

4. Pull the thread around the U-turn, then bring it back up.

5. To thread the take-up lever, draw thread up and bring

thread back down again from right to left along the slit.

6. Pull thread downward along the slit.

7. Draw thread through thread guide from right side opening.

8. Pass through needle eye from front to back.

Refer to next page for instructions on how to use the built-

in needle threader.

15

THREADING THE NEEDLE EYE

CAUTION

DRAWING UP THE BOBBIN THREAD

This machine can start to sew without drawing up the bobbin

thread. If you want to start sewing with longer bobbin thread,

draw up the bobbin thread as follows.

1. Insert the bobbin into the bobbin holder as shown on page

13, but do not cut thread.

2. Raise the presser foot.

3. Hold upper thread loosely and turn hand wheel toward you

one complete revolution.

To prevent accidents:

1. Keep ﬁ ngers away from all moving parts. Special care

is required around the needle.

2. Do not lower the threader lever while machine is

operating.

NOTE:

The needle threader is used for needle sizes 11/80 and 14/90.

1. Lower the presser foot.

2. Check that the needle is raised to its highest position. If it is

not, raise needle by turning the handwheel toward you.

3. Lower the threader slowly and draw thread through thread

guide (a) and pull toward the right.

4. Lower the lever as far as it will go. The threader will turn

and the hook pin will go through the needle eye.

5. Draw the thread into the guide, ensuring that the thread is

under the hook pin.

6. Hold thread loosely and release the lever.

As the threader rotates back, the hook pin will pass through

the needle eye, forming a loop of thread.

7. Pull thread out about 10 cm (4 inches) through the needle

eye.

THREADING THE MACHINE

4. Pull upper thread lightly. Bobbin thread will come up in a

loop.

5. Pull both upper and bobbin threads about 10 cm (4 inches)

toward the back of presser foot.

6. Replace the bobbin cover. (See page 13)

THREADING THE MACHINE

16

HOME SCREEN / HOME BUTTON

H

OME SCREEN (A)

When you have attached the embroidery unit correctly, the

Home Screen will appear.

You can start selecting and editing embroidery from this

screen.

HOME BUTTON (B)

You can go back to the Home Screen from anywhere by

pressing the Home Button.

At this time, all selected designs or letters and editing for

embroidery will be cleared.

A

B

C

(a)

D

i

ii

iii

TOP SIDE BOTTOM SIDE

EMBROIDERY PREPARATION

EMBROIDERY MACHINE SETTINGS

S

ETTING BUTTON (C)

Before or during the embroidery process, you can adjust the

machine settings by pressing the Setting Button.

The Setting Screen will appear. (a)

This screen is scrolled by pressing the right side arrow buttons.

Pressing the Setting Button again, machine will return to

previous screen.

NOTE:

All settings except for thread tension will remain until you

change them. Thread tension will return to pre-set when you

change the design.

THREAD TENSION (D)

This embroidery machine adjusts thread tension automatically.

However, depending on the thread or fabric being used, it

may be necessary to modify the tension setting to achieve the

desired results.

To obtain the desired thread tension, adjust as follows.

i. CORRECT THREAD TENSION

Upper thread appears slightly on the bottom side of fabric.

ii. UPPER THREAD TOO TIGHT

Bobbin thread appears on the top side of fabric.

Decrease the upper thread tension by pressing the “-”

button.

iii. UPPER THREAD TOO LOOSE

Upper thread is loose or makes loops.

Increase the upper thread tension by pressing the “+”

button.

When thread tension is changed from the default (pre-set)

setting, the number will be highlighted.

NOTE:

If the bobbin has been threaded or inserted incorrectly, or if

the upper thread has not been threaded correctly, good thread

tension cannot be achieved. Check to make sure that the

bobbin and upper thread are correctly threaded before making

any adjustments.

17

i

ii

i

ii

1

2

3

5

4

6

STOP FOR CUT

When starting to embroider, the machine can be set so that it

will stop after a few stitches, allowing you the opportunity to cut

the thread tail.

You can select or deselect this function, as follows:

i. Stop for Cut is activated.

ii. Stop for Cut is deactivated.

AUDIBLE BEEP

You can turn the audible beep on or off by pressing this button.

i. Audible Beep is on.

ii. Audible Beep is off.

CONTRAST OF SCREEN

You can adjust the contrast of the LCD screen.

By pressing “+” or “–” button, contrast will increase or

decrease.

EMBROIDERY PREPARATION

CALIBRATION SCREEN

If the icons on the screen (in relationship to where you touch

the screen) seem misaligned, the screen may need calibrating,

as follows:

1. Scroll down and press calibration screen button.

2. Press the each “O” mark indicated on the screen 5

positions. (4 corners and center)

When calibration is completed, setting screen will appear

again.

SOFTWARE VERSION

Software version of this embroidery machine will be indicated

at the bottom of this screen.

You can update the software by using the USB embroidery

stick.

(See page 11)

EMBROIDERY PREPARATION

(example)

18

FABRIC AND STABILIZER

Embroidery can be applied to many different types of

fabrics. Regardless of the fabric, it will be necessary to use

an appropriate type of stabilizer. (See page 29 for more

information)

Stabilizer serves as a foundation, holding fabric securely while

the embroidery machine stitches out the design, eliminating

distortion in the fabric and the design.

Different fabrics will require different types of stabilizer,

depending on the nature of the fabric and the density of the

design being embroidered. But most embroidery designs will

stitch out looking their best if the fabric is properly stabilized.

Stabilizer is mainly used as a backing, but at times, a stabilizer

is used on the top of the project as well.

A “Backing” goes on the back side of the area to be

embroidered. It may be hooped along with the fabric or hooped

alone, depending on the fabric and project.

A “Topper” means that an additional stabilizer is placed on the

top of the fabric, either hooped with the fabric or secured in

another manner. Its function is to ensure that the texture or loft

of the fabric is held down, providing a smooth surface for the

embroidery.

Though there are many types of stabilizers available, the most

common types are tear-away, wash away, and cut away.

Stabilizers come in different weights as well. After selecting the

best type of stabilizer for the project, choose the appropriate

weight. A good general rule is that the weight of the stabilizer

be compatible with the fabric.

Tear-away stabilizers are temporary, so once the excess is

removed after embroidering, the fabric itself must be able to

support the design on its own.

Tear-away stabilizers are usually recommended for woven

fabrics.

Cut-away stabilizers are permanent, and therefore a better

choice for supporting embroidery on unstable fabrics, to

prevent distortion. Simply trim away the excess from around

the design. Even after frequent laundering, the embroidery

design will stay intact.

Wash-away stabilizers rinse away from the embroidered area.

Though they are a good choice when sewing very light weight

fabrics, they can also be used as a topping. After removing the

main excess stabilizer, the rest is simply rinsed away.

There are also fusible and non-fusible version of stabilizer

available. Fusible stabilizers can be ironed onto the back of

the area to be embroidered, preventing distortion of the fabric

while hooping.

However, for fabrics that may be more sensitive to ironing,

the non-fusible stabilizers are used. In these cases, another

helpful tool is a temporary fabric spray adhesive. Use this to

temporarily ‘hold’ the fabrics and stabilizer while hooping and

embroidering, to prevent the fabrics from shifting during the

embroidery process.

Knowing how to properly stabilize involves a little trial and error

at ﬁ rst. Follow the stabilizer manufacturer’s recommendations,

for best results.

a

b

cd

EMBROIDERY PREPARATION

Generally, the stabilizer should be larger in size than the hoop

with which it is being used. When embroidery is completed,

use a ﬁ ne point scissor to carefully remove any excess

stabilizer from the embroidery area.

a. Stabilizer

b. Hoop position

c. Fabric (Under side)

d. Embroidery surface (Top side)

19

SECURING FABRIC IN EMBROIDERY

HOOP

For the best embroidery results, place a layer of stabilizer

beneath the fabric. When hooping stabilizer and fabric make

sure that they are smooth and securely hooped.

1. Open the quick release lever on the outer hoop and remove

the inner hoop.

2. Place the outer hoop on a ﬁ rm ﬂ at surface with the screw

on the lower right. There is a small arrow in the center of

the left edge of the outer hoop which will line up with a

small arrow on the inner hoop.

3. Place stabilizer and the fabric, with the right sides facing

up, on top of the outer hoop.

1

2

3

4

5

6

EMBROIDERY PREPARATION

4. Place the inner hoop on top of the fabric with the small

arrow at the left edge and push ﬁ rmly into the outer hoop.

5. Close the quick release lever. Don’t force the quick release

lever. If it seems as though it doesn’t want close, loosen the

retaining screw ﬁ rst and then try closing the quick release

lever again.

6. Adjust the pressure of the outer hoop by turning the

retaining screw. The fabric should be taut in the hoop for

the best results.

NOTE:

When embroidering additional designs on the same fabric,

open the quick release lever, move the hoop to the new

position on the fabric and close the quick release lever. When

changing type of fabric, you might need to adjust the pressure

using the retaining screw. Do not force the quick release lever.

ATTACHING THE EMBROIDERY HOOP

TO THE MACHINE

1. Raise the presser foot. Raise the needle to its highest

position by turning the hand wheel toward you.

2. Slide the hoop onto the embroidery unit from front to back

until it clicks into place.

NOTE:

Presser foot lever can be raised and held in a higher position

to help passing the hoop under the foot.

REMOVING THE HOOP FROM THE MACHINE

Press and hold the release lever (a) on the hoop connection

assembly, then slide the hoop toward you.

a

EMBROIDERY PREPARATION

20

HOME SCREEN

Selecting designs to embroider begins with the Home Screen.

The Home Screen has two main selections.

a. Selecting a design, editing and stitching.

b. Programming letters, editing and stitching.

a

b

1

c

2

3

d

e

1

2

3

f

g

h

EMBROIDERY COLLECTION

Your machine comes with 200 embroidery designs, as well as

embroidery fonts. You will ﬁ nd 69 of these designs, plus the

fonts, built-in to the machine. The remainder of the designs

are on the USB stick.

The USB stick also has 2 PDF ﬁ les with information about the

designs. For more information about this, see page 11.

SELECTING A DESIGN

T

O SELECT A BUILT-IN DESIGN

Your machine has 69 built-in embroidery designs.

1. Press the Design button on the Home Screen.

A ten-key screen will appear.

NOTE:

Press the Machine tab (c) if USB tab is activated.

2. Select the design from the Embroidery Collection and press

the design number on the ten-key screen.

Selected number will appear in the top left of LCD.

To delete a number, press the Delete button (d).

If you want to know about selected design, press the info

button (e). The following information is indicated on the

screen.

i. Design name

ii. Design width & height

iii. Total number of colors

iv. Total number of stitches

By pressing “

✓

” button, the information will disappear and

ten-key screen will appear again.

3. Press the “

✓

” button at ten-key screen.

The design is selected and Embroidery Placement screen

will appear.

SELECTING DESIGNS

TO SELECT A USB DESIGN

Your machine can read “.xxx” and “.dst” embroidery data

stored in the USB embroidery stick.

1. Insert the USB embroidery stick into the USB socket.

2. Press the design button on the Home Screen and then

press the USB tab (f).

Data list will appear in the screen.

Press the ﬁ le or folder to select or open and press the “

✓

”

button.

When folder is opened, the list of designs included in that

folder will appear (g).

To go back, press the arrow button on the top line (h).

Press the info button for more information about the

selected design.

NOTE:

If the USB stick or a folder is empty or if readable ﬁ le is not

included, empty mark will appear.

3. When ﬁ le is selected, embroidery placement screen will

appear.

La page charge ...

SINGER EM200 Sewing Machine Manuel utilisateur

Ce manuel convient également à

SINGER EM200 Sewing Machine Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents