Pfaff creative 4.0 Le manuel du propriétaire

Owner´s manual

This household sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be followed, including the

following:

Read all instructions before using this household sewing machine.

DANGER – To reduce the risk of electric shock:

• A sewing machine should never be left unattended when plugged in. Always unplug this sewing

machine from the electric outlet immediately after using and before cleaning.

WARNING – To reduce the risk of burns, À re, electric

shock, or injury to person:

• This sewing machine is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the sewing machine by a person responsible for their

safety.

• Children should be supervised to ensure that they do not play with the sewing machine.

• Use this sewing machine only for its intended use as described in this manual. Use only attachments

recommended by the manufacturer as contained in this manual.

• Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if

it has been dropped or damaged, or dropped into water. Return the sewing machine to the nearest

authorized dealer or service center for examination, repair, electrical or mechanical adjustment.

• Never operate the sewing machine with any air openings blocked. Keep ventilation openings of the

sewing machine and foot controller free from the accumulation of lint, dust, and loose cloth.

• Keep À ngers away from all moving parts. Special care is required around the sewing machine needle.

• Always use the proper needle plate. The wrong plate can cause the needle to break.

• Do not use bent needles.

• Do not pull or push fabric while stitching. It may deÁ ect the needle causing it to break.

• Wear safety glasses.

• Switch the sewing machine off (“0”) when making any adjustment in the needle area, such as threading

needle, changing needle, threading bobbin, or changing presser foot, etc.

• Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or when

making any other user servicing adjustments mentioned in the instruction manual.

• Never drop or insert any object into any opening.

• Do not use outdoors.

• Do not operate where aerosol (spray) products are being used or where oxygen is being administrated.

• To disconnect, turn all controls to the off (“0”) position, then remove plug from outlet.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• This sewing machine is provided with double insulation. Use only identical replacement parts. See

instructions for Servicing of Double-Insulated Appliances.

SAVE THESE INSTRUCTIONS

SERVICING OF DOUBLE INSULATED PRODUCTS

In a double-insulated product, two systems of insulation are provided instead of grounding. No ground

means is provided on a double-insulated product, nor should a means for grounding be added to the

product. Servicing of a double-insulated product requires extreme care and knowledge of the system, and

should be done only by qualiÀ ed service personnel. Replacement parts for a double-insulated product must

be identical to those parts in the product. A double-insulated product is marked with the words ‘DOUBLE

INSULATION’ or ‘DOUBLE INSULATED’.

Congratulations!

Congratulations on purchasing your new PFAFF® creative™ 4.0 sewing and embroidery machine. As a

sewing enthusiast, you have acquired a machine that features the very latest in both design and technology,

enabling you to transform all your creative ideas into reality.

Before you start, please spend some time reading this owner’s manual. You will soon discover how to

maximize the use of your machine. Your authorized PFAFF® Dealer will of course also be pleased to help

you at any time.

Your PFAFF® creative™ 4.0 sewing and embroidery machine will deÀ nitely enable you to experience a

totally new dimension of sewing and embroidery.

Table of contents

1

Introduction 1:7

Machine overview 1:8

Front side ......................................................................1:8

Rear side .......................................................................1:9

Top parts .......................................................................1:9

Accessory tray ..............................................................1:9

Parts of the embroidery unit ....................................1:10

Included accessories 1:10

Stitch overview 1:12

Utility stitches ............................................................ 1:12

Decorative stitches ....................................................1:15

Alphabets ....................................................................1:17

2

Preparations 2:1

Unpacking .................................................................... 2:2

Connecting the foot control cord ..............................2:2

Connect the power cord and foot control ................2:2

Pack away after sewing .............................................2:3

LED lights .....................................................................2:3

Free arm ........................................................................ 2:3

Thread cutter ................................................................ 2:3

Stylus holder ................................................................2:3

Spool pins ..................................................................... 2:4

Threading the machine ...............................................2:5

Bobbin winding ...........................................................2:7

Inserting the bobbin .................................................... 2:8

IDT (Integrated dual feed) .........................................2:9

Changing the needle ...................................................2:9

Needles .......................................................................2:10

Changing the presser foot ........................................2:11

Lowering feed dogs ...................................................2:11

USB ports ....................................................................2:12

Connect machine to computer .................................2:13

5D™ Embroidery Software ......................................2:13

Installing your software ...........................................2:13

Install hardware drivers and connect the

embroidery machine .................................................2:13

How to launch the programs ...................................2:14

Embroidery Machine Communication module ....2:14

How to update your machine .................................. 2:14

Viewing and printing PDF Guides .........................2:14

Buttons and icons ......................................................2:13

3

PFAFF® HD screen 3:1

Task bar ........................................................................3:2

Common icons ............................................................. 3:3

Selection menu .............................................................3:4

Embroidery edit ...........................................................3:5

Embroidery text editor ...............................................3:6

Embroidery stitch-out .................................................3:6

Sequencing ...................................................................3:7

Stitch Creator ...............................................................3:7

Settings menu 3:8

Machine settings ..........................................................3:8

Sound settings ............................................................3:11

Screen settings ............................................................ 3:12

Info menu 3:13

Quick help 3:13

4

Sewing mode 4:1

Sewing mode - overview 4:2

Select a stitch ................................................................ 4:3

Raise and lower the presser foot ............................... 4:3

Option bar 4:4

Save options .................................................................4:4

Tie-off options ..............................................................4:5

Speed control ................................................................4:6

Sewing programs .........................................................4:6

Balance .......................................................................... 4:8

Stitch settings 4:8

Sewing techniques 4:12

Three-step zigzag ......................................................4:12

Buttonholes .................................................................4:12

Sew on a button .........................................................4:14

Sewing hems in heavy fabric ...................................4:15

Handlook quilting .....................................................4:15

Blindhem stitch .......................................................... 4:15

Sewing in zippers ......................................................4:16

Rolled hem ..................................................................4:16

Common sewing pop-ups 4:17

5

Sequencing 5:1

Sequencing - overview 5:2

Create a sequence ........................................................ 5:3

Option bar 5:4

Save options ................................................................. 5:4

Sequence commands ...................................................5:4

Horizontal preview .....................................................5:5

Sewing a sequence .......................................................5:5

Important sequencing information ...........................5:6

Common sequencing pop-ups 5:6

6

Stitch Creator 6:1

Stitch Creator - overview 6:2

Touch functions ...........................................................6:5

Save options ................................................................. 6:5

Important Stitch Creator information ......................6:6

Common Stitch Creator pop-ups 6:6

7

Embroidery preparations 7:1

Embroidery unit overview .........................................7:2

Built-in designs ............................................................7:2

Embroidery hoop overview ....................................... 7:2

creative™ 4.0 Embroidery collection ........................ 7:3

Connect the embroidery unit .....................................7:3

Remove the embroidery unit .....................................7:3

To hoop the fabric........................................................7:4

Slide on the hoop .........................................................7:4

Getting started embroidering ....................................7:5

8

Embroidery mode - edit 8:1

Embroidery edit - overview 8:2

Load a design ...............................................................8:2

Load a font ....................................................................8:3

Load a stitch ................................................................. 8:3

Zoom ............................................................................. 8:3

Select design(s) .............................................................8:4

Adjustments .................................................................8:5

Touch functions ...........................................................8:6

Option bar 8:7

Save design ...................................................................8:7

More options ................................................................8:8

Select hoop ....................................................................8:9

Thread color edit ......................................................... 8:9

Embroidery stitch editor ..........................................8:10

Embroidery text editor .............................................8:12

Common embroidery edit pop-ups 8:14

9

Embroidery mode - stitch-out 9:1

To enter embroidery stitch-out .................................. 9:2

Embroidery stitch-out - overview 9:2

Crosshair .......................................................................9:2

Color list ........................................................................9:2

Embroidery information ............................................9:3

Option bar 9:4

More options ................................................................9:4

Speed control ................................................................9:4

Hoop position .............................................................. 9:5

Precise positioning ......................................................9:6

Common embroidery stitch-out pop-ups 9:9

10

Files & Folders 10:1

Files & Folders - overview 10:2

Browse Files & Folders ............................................. 10:3

Organize......................................................................10:6

Common Files & Folders pop-ups 10:7

11

Maintenance 11:1

Cleaning the machine 11:2

Troubleshooting 11:3

Index 11:5

Intellectual Property 11:10

Some fabrics have a lot of excess dye which can

cause discoloration on other fabric but also on your

sewing machine. This discoloring may be very

difÀ cult or impossible to remove.

Fleece and denim fabric, especially red and blue,

often contain a lot of excess dye.

If you suspect that your fabric/ready-to-wear

garment contains a lot of excess dye, always pre-

wash it before sewing to avoid the discoloring.

Introduction

1:8

4

3

2

1

6

5

8

7

10

15

5

13

26

24

28

27

30

29

18 19 20 21 22 23

12

14

16

17

25

9

11

Introduction

Machine overview

1. Lid with stitch chart

2. Threading slots

3. Thread cutter

4. Sensormatic buttonhole foot socket

5. LED-lights

6. Built-in needle threader

7. Needle bar

8. Needle thread guide

9. Bobbin cover

10. Stitch plate

11. Free arm

12. Presser foot

13. Presser foot bar and presser foot holder

14. Needle screw

15. Reverse

16. Reverse indicator

17. Action indicator

18. Presser foot up and extra lift toggle

19. Presser foot down and pivot toggle

20. Start/stop

21. Thread snips

22. Immediate tie-off

23. Stitch restart

24. Needle up/down

25. Button ruler

26. Handwheel

27. PFAFF® HD screen

28. Built-in USB ports

29. Stylus holder

30. Main switch, connectors for power cord and

foot control

Front side

1:9

33

32

31

363534 37 38 39 40

42 41

434445

48

47

46

Introduction

Rear side

31. Handle

32. IDT

33. Embroidery unit connection socket

Top parts

34. Pre-tension device for threading and bobbin

winding

35. Bobbin winder thread guide

36. Thread guide

37. Bobbin thread guides

38. Bobbin winder lever

39. Bobbin spindle

40. Bobbin thread cutter

41. Auxiliary spool pin

42. Spool caps

43. Spool pin

44. Thread tension

45. Take-up lever

Accessory tray

The accessory tray features special compartments

for presser feet and bobbins, plus space for needles

and other accessories. Store the accessories in the

tray so they are easily accessible.

46. Space for accessories

47. Removable tray for presser feet

48. Removable bobbin holder

Accessory tray

1:10

57

565554

6160

59

58

6463

62

65

66

67

68

69

51

52

53

49

50

Introduction

Parts of the embroidery unit

(type BE16)

49. Embroidery unit release button

50. Level adjusting feet

51. Embroidery unit socket

52. Embroidery hoop connection assembly

53. Embroidery arm

Included accessories

Accessories

54. Stylus

55. Thread net

56. Edge guide

57. Felt pad

58. USB Embroidery stick

59. Screwdriver

60. Seam ripper

61. Brush

62. Spool cap, large (2)

63. Spool cap, medium

64. Spool cap, small

65. Bobbins

66. Multi-purpose tool

67. Hoop clips

Included hoops

68. creative™ 120 Square Hoop (120x120)

69. creative™ Elite Hoop (260x200)

Included accessories not in picture

• Foot control

• Foot control cord

• Power cord

• USB cord (P/N:412 62 59-04)

• Needles

• 5D™ Embroidery Machine Communication

CD

• creative™ 4.0 Embroidery collection

1:11

Introduction

Presser feet

Presser foot 0A

Standard presser foot with IDT (attached on the machine

upon delivery)

This foot is used mainly for straight stitching and zigzag

stitching with a stitch length longer than 1.0mm.

Presser foot 1A

Fancy stitch foot with IDT

This foot is used for decorative stitches. The groove on the

underside of the foot is designed to Á ow smoothly over

the stitches.

Presser foot 2A

Fancy stitch foot

When sewing decorative stitches or short zigzag stitches

and other utility stitches with less than 1.0mm stitch

length, use this foot. The groove on the underside of the

foot is designed to Á ow smoothly over the stitches.

Presser foot 3

Blindhem foot with IDT

This foot is used for blindhem stitches. The toe on the foot

guides the fabric. The red guide on the foot is designed to

ride along the fold of the hem edge.

Presser foot 4

Zipper foot with IDT

This foot can be snapped on either the right or the left of

the needle, making it easy to sew close to both sides of the

zipper teeth. Move needle position to right or left to sew

closer to zipper teeth.

Presser foot 5A

Sensormatic buttonhole foot

When connected to the machine, the buttonhole is sewn in

a suitable length to the button size that has been entered

into the machine.

Presser foot 5M

Manual buttonhole foot

This foot is used for sewing manual buttonholes. Use the

markings on the foot to position the garment edge. The

À nger on the back of the foot holds cording for corded

buttonhole.

Presser foot 6A

Embroidery/Sensormatic free-motion foot

This foot is used for embroidery and free-motion sewing.

This foot can also be used for darning.

Presser foot 7

Rolled hem foot with IDT, 3mm

This foot is used to sew narrow hems in light to medium

weight fabric.

Important: Make sure that the IDT is disengaged when using presser feet 2A, 5A, 5M or 6A.

1:12

Introduction

Stitch overview

Utility stitches

Stitch Stitch number Name Description

1.1.1 Straight stitch

For seaming and topstitching. Select from 37 different needle positions.

Note: This stitch makes a stronger tie-off than stitch 2.1.1.

1.1.2

Stretch triple straight

stitch

Reinforced seam. Topstitching.

1.1.3 Straight stitch reverse Sew continuous reverse with strong tie-off.

1.1.4 Basting stitch

Single stitch used for basting. Touch foot control to sew one stitch.

Move fabric manually to desired position and touch foot control again

to sew another stitch.

1.1.5 Zigzag stitch Reinforce seams, clean À nish, stretch sewing, lace insertion.

1.1.6

Zigzag stitch, right or left

needle position

Reinforce seams, clean À nish, stretch sewing.

1.1.7 Z-zigzag stitch Applique, couching, eyelets.

1.1.8 Stretch triple zigzag stitch Elastic stitch for decorative hems or topstitching.

1.1.9 Three-step zigzag stitch Sewing elastic, darning, patching.

1.1.10 Elastic stitch Sewing elastic, darning, patching.

1.1.11 Triple stretch stitch Sewing elastic, darning, patching and decorative sewing.

1.1.12 Honeycomb stitch

Decorative stitch for stretch fabrics and hems. Also used with elastic thread in

the bobbin.

1.1.13 Bridging stitch Joining fabrics and quilt batting, decorative stitch for quilting, hemstitching.

1.1.14 Foundation elastic stitch

Joining stitch for undergarments, terry cloth, leather, bulky fabrics where

overlapping the seams.

1.1.15 Crosshem stitch Elastic decorative hem for stretch fabrics.

1.1.16 Blindhem stitch Sewing blindhems on woven fabrics.

1.1.17 Elastic blindhem stitch Sewing blindhems on stretch fabrics.

1.1.18 Stretch tricot stitch Sewing seams on stretch fabrics.

1.2.1 Closed overlock Seam and overcast stretch fabrics in one step.

1:13

Introduction

1.2.2 Closed overlock Seam and overcast in one step.

1.2.3 Closed overlock Seam and overcast in one step with reinforced edge.

1.2.4 Elastic overcast Seam and overcast stretch fabrics in one step.

1.2.5 Standard overcast Seam and overcast stretch fabrics in one step with reinforced edge.

1.2.6 Overlock Seam and overcast stretch fabrics in one step.

1.2.7 Closed overlock Seam and overcast in one step, patch, hem.

1.2.8 Stretch knit overlock Seam and overcast stretch fabrics in one step.

1.2.9 Reinforced overlock Seam and overcast stretch fabrics in one step and reinforce.

1.2.10 Finished edge overlock Seam and overcast stretch fabrics in one step with reinforced edge.

1.2.11 Mock cover hem Create the look of a serger cover hem for stretch fabrics.

1.2.12 Open overlock blindhem Create decorative overlock blindhem for woven fabrics.

1.2.13 Closed overlock blindhem Create decorative overlock blindhem for stretch fabrics.

1.3.1 Linen buttonhole Buttonhole for blouses, shirts and linen.

1.3.2 Standard buttonhole Basic buttonhole for blouses, shirts and jackets. Also for pillowcases.

1.3.3

Rounded buttonhole with

pointed tack

Buttonhole for garments.

1.3.4

Rounded buttonhole with

lengthwise tack

Buttonhole for garments.

1.3.5

Rounded buttonhole with

crosswise tack

Buttonhole for garments.

1.3.6

Eyelet buttonhole with

pointed tack

Tailors buttonhole or decorative buttonhole.

1.3.7

Eyelet buttonhole with

lengthwise tack

Tailors buttonhole for jackets and trousers.

1:14

Introduction

1.3.8 Rounded buttonhole Buttonhole for light garments or jackets.

1.3.9

Decorative buttonhole

with triangle tack

Decorative buttonhole.

1.3.10 Stretch buttonhole Buttonhole for stretch fabrics.

1.3.11 Cross stitch buttonhole Decorative buttonhole.

1.3.12 Decorative buttonhole Decorative buttonhole.

1.3.13

Professional eyelet

buttonhole

Professional tailors buttonhole for jackets and trousers.

1.3.14

Decorative eyelet

buttonhole

Decorative buttonhole for jackets.

1.3.15

Heirloom round

buttonhole with pointed

tack

Decorative heirloom buttonhole.

1.3.16 Button sewing Sew on buttons or tacking.

1.4.1 Eyelet Heirloom sewing decorative trim.

1.4.2 Decorative eyelet Heirloom sewing decorative trim.

1.4.3 Decorative eyelet Heirloom sewing decorative trim.

1.5.1

Programmable darning

stitch

Darning holes or damaged fabric.

1.5.2

Programmable reinforced

darning stitch

Reinforced darning holes or damaged fabric.

1.5.3 Bartack Automatically reinforce seams and pockets.

1.5.4 Denim bartack Automatically reinforce seams and pockets decoratively.

1.5.5 Decorative bartack Automatically reinforce seams and pockets decoratively.

1.5.6 Cross bartack Automatically reinforce seams and pockets.

1.5.7 Decorative tack Automatically decorative topper for seams and pockets.

1:15

Introduction

Decorative stitches

2.1 Quilt stitches - Handlook stitches 2.2 Quilt stitches - Antique quilt stitches

2.3 Quilt stitches - Stippling stitches

3.1 Needle art stitches - Cross stitches 3.2 Needle art stitches - Hemstitches

3.3 Needle art stitches - Antique hand embroidery stitches

2.4 Quilt stitches - Crazy patch stitches

3.3 Needle art stitches - Antique hand embroidery stitches

1:16

Introduction

3.4 Needle art stitches - Smocking stitches 4.1 Decorative stitches - Scallop edges

4.2 Decorative stitches - Satin stitches

4.4 Decorative stitches - Art stitches 4.5 Decorative stitches - Ornamental stitches

4.6 Decorative stitches - Bows and hearts

4.3 Decorative stitches - Leaves and Á owers

4.7 Decorative stitches - Fun stitches

1:17

Introduction

4.8 Decorative stitches - Borders

Alphabets

Comic Outline

Cyrillic

Script

Preparations

2:2

123

Preparations

Unpacking

1. Place the box on a steady, Á at surface. Lift the

machine out of the box and remove the outer

packaging and lift off the machine carrying

case.

2. Remove all other packing material and the

plastic bag.

3. Slide off the accessory tray and remove the

styrofoam inside.

Note: Styrofoam left in the accessory tray while sewing

may affect stitch quality. The styrofoam is for packing

purposes only and should be removed.

Connecting the foot control cord

Among the accessories you will À nd the foot

control cord. Connecting the foot control cord to

the foot control is only neccessary the very À rst

time you are going to use the machine.

1. Take out the foot control cord. Turn the foot

control over. Connect the cord to the socket

inside the space of the foot control.

2. Push À rmly to make sure it is properly

connected.

3. Lay the cord in the slot on the underside of the

foot control.

Connect the power cord and foot control

Note: Before plugging in the foot control, check to

ensure that it is type “FR5” (see underside of foot

control).

1. Connect the foot control cord to the front

socket on the bottom right side of the machine

(1).

2. Connect the power cord to the rear socket on

the bottom right side of the machine (2). Plug

the cord into the wall socket.

3. Press the ON/OFF switch to ON to turn on

power and light (3).

For the USA and Canada

This sewing machine has a polarized plug (one

blade wider than the other). To reduce the risk

of electric shock, this plug is intended to À t in a

polarized outlet only one way. If the plug does not

À t fully in the outlet, reverse the plug. If it still does

not À t, contact a qualiÀ ed electrician to install the

proper outlet. Do not modify the plug in any way.

La page charge ...

Pfaff creative 4.0 Le manuel du propriétaire

Pfaff creative 4.0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents