Viking Emerald 116 Manuel utilisateur

Catégorie
Machines à coudre
Taper
Manuel utilisateur
KEEPING THE WORLD SEWING
User’s Guide
This houshold sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic safety precautions should always be followed, including
the following:
Read all instructions before using this household sewing machine.
DANGER - To reduce the risk of electric shock:
A sewing machine should never be left unattended when plugged in. Always unplug this sew-
ing machine from the electric outlet immediately after using and before cleaning.
Always unplug before relamping. Replace bulb with same type rated 15 Watt (for model 116) or
5 Watts (for model 118 and 122).
WARNING - To reduce the risk of burns, À re, electric
shock, or injury to persons:
This sewing machine is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the sewing machine by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the sewing machine.
Use this sewing machine only for its intended use as described in this manual. Use only attach-
ments recommended by the manufacturer as contained in this manual.
Never operate this sewing machine if it has a damaged cord or plug, if it is not working prop-
erly, if it has been dropped or damaged, or dropped into water. Return the sewing machine to
the nearest authorized dealer or service center for examination, repair, electrical or mechanical
adjustment.
Never operate the sewing machine with any air openings blocked. Keep ventilation openings
of the sewing machine and foot controller free from the accumulation of lint, dust, and loose
cloth.
• Keep À ngers away from all moving parts. Special care is required around the sewing machine
needle.
Always use the proper needle plate. The wrong plate can cause the needle to break.
Do not use bent needles.
Do not pull or push fabric while stitching. It may deÁ ect the needle causing it to break.
Wear safety glasses.
Switch the sewing machine off (“0”) when making any adjustment in the needle area, such as
threading needle, changing needle, threading bobbin, or changing presser foot, etc.
Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or
when making any other user servicing adjustments mentioned in the instruction manual.
Never drop or insert any object into any opening.
Do not use outdoors.
Do not operate where aerosol (spray) products are being used or where oxygen is being admin-
istrated.
To disconnect, turn all controls to the off (“0”) position, then remove plug from outlet.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
SAVE THESE INSTRUCTIONS
1
Overview ........................................................2
Extension Table .............................................3
Free-arm sewing ............................................3
Standard Accessories and Storage ..............4
Getting ready to sew 5-20
Connecting the Power Supply .....................5
Adjusting the Sewing Speed ........................6
Needle up/down ...........................................6
Sewing Guide Reference Chart ...................7
Reverse Lever .................................................8
Presser Foot Pressure Dial ..........................8
Lowering the Feed Teeth .............................8
Raising and Lowering the Presser Foot
......9
Changing the Presser Foot ..........................9
Changing the Needle ..................................10
Placing the thread spool
on the spool pin ..........................................11
Removing the bobbin .................................11
Bobbin Winding ..........................................12
Placing the bobbin ......................................13
Threading the Machine ..............................14
Needle threader ...........................................15
Bringing up the Bobbin Thread ................16
Stitches ..........................................................17
Stitch Selection ............................................18
Stitch Length ................................................18
Adjusting stretch stitch balance ................19
Stitch Width .................................................19
Variable needle position .............................19
Balancing Needle Thread Tension ...........20
Basic Sewing 21-23
Straight Stitch Sewing .................................21
Finishing sewing ..........................................22
Seam Guides on the Needle Plate ............23
Pivoting .........................................................23
Utility Stitches 24-38
Basic Zigzag ................................................ 24
Three-step Zigzag ...................................... 24
Seam and Overcast .................................... 24
Reinforced Straight Stitch .........................25
Button Sewing ............................................ 25
Automatic Buttonhole ...............................26
Corded Buttonhole .................................... 30
Manual Buttonhole .................................... 31
Sewing Zipper .............................................33
Blind Hem ................................................... 37
Non-stick Glide Foot H ............................38
Quilting Guide ............................................38
Presser Feet only model 122 38-39
Transparent Foot B .................................... 38
Gathering Foot ...........................................39
Quilter’s 1/4” Piecing Foot ...................... 39
Care and Maintenance 40-42
Cleaning the Hook Assembly area
and Feed Teeth ...........................................40
Replacing the Bobbin Case ....................... 41
Replacing the Light Bulb .......................... 41
Troubleshooting ......................................... 42
Table of Contents
2
6
7
Overview
1. Bobbin stop
2. Bobbin spindle
3. Hole for extra spool pin
4. Spool holder
5. Spool pin
6. Thread guide for bobbin winding
7. Thread take-up lever
8. Presser foot pressure dial
9. Face plate
10. Thread cutter
11. Needle threader
12. Needle plate
13. Extension table (Accessory
storage)
14. Bobbin cover plate
15. Bobbin cover plate release button
16. Thread tension dial
17. Needle up/down button (only
model 118 and 122)
18. Speed control slider (only model
118 and 122)
19. Reverse stitch lever
20. Sewing Guide
21. Stitch length dial
22. Stitch selection dial
23. Stitch width dial
24. Presser foot
25. Needle
26. Needle clamp screw
27. Ankle to hold foot
28. Thumbscrew
29. Carrying handle
30. Handwheel
31. Power switch, Emerald™ 118/122
31.a Power switch,Emerald 116
32. Foot control socket (only model
118 and 122)
33. Machine socket, model 118 and
122
33.a Machine socket, model 116
34. Drop feed lever
35. Free-arm
36. Buttonhole lever
37. Presser foot lift
22
21
1
2
3
4
5
8
9
10
11
16
12
13
14
15
17
19
18
20
24
25
26
28
27
29
30
31
32
34
35
36
37
23
33
31.a
33.a
3
Extension Table
To r e m o v e
Hook your À ngers on the bottom left of
the extension table and pull it to the left.
Free-arm sewing
For stitching sleeves, waistbands, pant
legs or any other tubular garments.
For darning socks or mending knees or
elbows.
To attach
Slide the extension table on and insert
the pins into the holes and push the
extension table to snap it in place.
1 Pin
2 Hole
1
2
Some fabrics have a lot of excess dye which can cause discoloration on other
fabric but also on your sewing machine. This discoloring may be very difÀ cult or
impossible to remove.
Fleece and denim fabric in especially red and blue often contain a lot of excess
dye.
If you suspect that your fabric/ready-to-wear garment contains a lot of excess
dye, always pre-wash it before sewing to avoid the discoloring.
4
4
8
16
17
18
13
19
20
21
22
23
Standard Accessories and
Storage
1. Utility Foot A
2. Utility Foot B
3. Buttonhole Foot C
4. Adjustable Blind Hem Foot
5. Zipper Foot E
6. Non-stick Glide Foot H
7. Edging Foot J
8. Automatic Buttonhole Foot R
9. Transparent Foot B (only model
122)
10. Quilter’s 1/4” Piecing Foot P (only
model 122)
11. Gathering Foot (only model 122)
12. Self-adhesive Glide Plates
13. Edge/quilting Guide
14. Needles
15. Bobbins
16. Screwdriver
17. Lint brush
18. Seam ripper (Buttonhole opener)
19. Spool holder (Large)
20. Spool holder (Small)
21. Vertical spool pin
22. Felt cushion
23. Accessory storage (Open the
extension table for storing
accessories.)
2
5
11
6
3
9
14
10
12
15
7
1
5
Getting ready to sew
Connecting the Power Supply
Turn the power switch off.
Insert the foot control plug into the
machine socket.
Insert the power supply plug into the
machine and the wall outlet.
Turn the power switch on.
1 Power switch
2 Foot control plug
3 Machine plug
4 Machine socket
5 Power supply plug
6 Wall outlet
NOTE: Before connecting to the power
supply, make sure the voltage shown on
the machine conforms to your electrical
power.
The foot control model that has to be
used for each sewing machine model are
shown in the table below.
1
2
4
3
6
5
For the USA and Canada:
This sewing machine has a polarized
plug (one blade wider than the
other). To reduce the risk of electric
shock, this plug is intended to À t in a
polarized outlet only one way. If the
plug does not À t fully in the outlet,
reverse the plug. If it still does not
À t, contact a qualiÀ ed electrician to
install the proper outlet.
DO NOT modify the plug in any
way!
For Emerald 118 and 122
1
2, 3
4
5
For Emerald 116
6
Foot control Model
Model
21361
Emerald
122 and
118
120V or
230 - 240V
Model
YC-190
Emerald
116
230 - 240V
Model
YC-482
Emerald
116
120V
6
Adjusting the Sewing Speed
You can control the sewing speed in two
ways; with the speed control slide or
with the foot control.
Speed control slide (model 118 and
122)
With the speed control slide, you can
change the sewing speed to suit your
needs. The slide limits how fast you can
sew.
To increase the sewing speed, slide the
bar to the right.
To reduce the sewing speed, slide the bar
to the left.
Foot control
You can control the sewing speed by using
the foot control. The harder you press the
foot control, the faster the machine sews.
If you press the foot control all the way,
the machine runs at the maximum speed
set by the speed control slide.
Needle up/down (model 118 and
122)
Touch this button to move the needle
down or up. The setting of the needle
stop position is changed at the same
time.
1 Needle up/down
1
For model 118 and 122
For model 116
7
Sewing Guide Reference Chart
Consult the Sewing Guide Reference Chart
for the fast easy way to select the best
stitch, stitch length, stitch width, thread
tension, presser foot and presser foot
pressure for your sewing technique and
fabric.
Look in the column for your fabric type:
WOVEN FABRICS: for stable fabrics
that have no stretch. Usually woven.
STRETCH FABRICS: for fabrics that
have stretch. Usually knit.
LEATHER/VINYL: for suede, real
leather and for artiÀ cial leather and
suede.
Select the stitch for the technique you want
to sew:
SEAM: sews two pieces of fabric
together.
NOTE: For Stretch Fabrics the Sewing
Guide Reference Chart recommends
setting the zig zag stitch length to
1.5 and stitch width to 1.5 for a seam
that stretches with the fabric.
OVERCAST: overcast fabric edges to
prevent them from fraying and to
help them lay Á at.
SEAM/OVERCAST: sews the seam and
overcasts the edge all at one time.
BASTE: a temporary stitching for
À tting garments, gathering and
marking. Use maximum stitch length.
NOTE: Basting will leave permanent
holes in leather and vinyl.
BLIND HEM: creates an invisible hem
on garments. Is not recommended
for light weight fabric or for leather/
vinyl.
HEM: sews the best visible or top
stitch hem for your fabric type and
weight.
BUTTONHOLE: sews the best
buttonhole possible for your fabric.
1
3
2
4 5 6 87
1 Fabric
2 Presser foot pressure
3 Sewing technique
4 Stitch
5 Presser foot
6 Thread tension
7 Stitch length
8 Stitch width
8
Reverse Lever
When you press the reverse lever
downwards, the machine will sew in
reverse. The machine will only sew in
reverse as long as the reverse lever is
pressed down.
1 Reverse lever
Presser Foot Pressure Dial
Turn the pressure dial to adjust the
pressure of the presser foot on the
fabric when sewing on different
thicknesses of fabric. The pressure dial
should be set at 3 for regular sewing.
Reduce the pressure to 2 for appliqué,
cutwork and basting. Set the setting mark
at 1 when sewing stretch fabrics, chiffon,
lace, organdy and other À ne fabrics. Set
on 0 for free motion.
1 Setting mark
Lowering the Feed Teeth
The drop feed lever is located on the
free-arm on the back of the machine.
To lower the feed teeth, push the lever in
the direction of the arrow, as illustrated.
To raise the feed teeth, push the lever in
the direction of the arrow, as illustrated,
and turn the handwheel toward you or
start sewing to bring the feed teeth up.
The feed teeth must be up for regular
sewing.
1 Raised position
2 Lowered position
1
1
2
1
9
Raising and Lowering the
Presser Foot
The presser foot is raised and lowered
with the presser foot lever. The presser
foot must be down when sewing.
By raising the presser foot lever as far as
it goes the lift height of the presser foot
can be increased by 1/4” (0.6 cm). This
is useful for easy removal of the presser
foot or when placing heavy fabrics under
the foot.
1 Lowered position
2 Normal lift height
3 Extra lift height
Changing the Presser Foot
Turn off the power switch
1 Make sure the needle is in the
highest position. Pull the presser
foot towards you.
2 To put foot on, line up the cross pin
on the foot between the spring and
the presser foot ankle. Press back
until the foot snaps into place.
1
2
3
2
3
1
2
10
Changing the Needle
Turn off the power switch.
Your machine uses standard sewing
machine needles.
1 Lower the presser foot. Loosen the
screw in the needle clamp by turning
it counterclockwise. Remove the
needle.
2 Push up the new needle as far as it
will go with the Á at side away from
you. Tighten the screw À rmly by
turning it clockwise.
a Stop
b Flat side
c Needle clamp screw
To check for a good needle:
Put the Á at side of the needle onto
something Á at (needle plate, glass etc.).
The gap between the needle and the Á at
surface should be consistent.
Never use a blunt needle. A damaged
needle can cause permanent snags or
runs in knits, À ne silks and silk-like-
fabrics.
NOTE: Check the needle frequently for
barbed or blunt points.
a
b
c
c
2
1
11
Placing the thread spool on
the spool pin
Place the thread spool on the spool pin
with the thread coming off as illustrated.
With large thread spools, the large
holder is placed in front of the thread. If
you use narrow thread spools, the small
holder is placed in front of the thread.
1 Large spool holder
2 Small spool holder
Removing the bobbin
Turn off the power switch.
1 Push the bobbin cover release
button to the right and remove the
cover.
a Release button
b Bobbin cover plate
2 Lift out the bobbin.
1
2
a
b
1
2
12
Bobbin Winding
1 Pull the handwheel out to put the
machine in bobbin wind position (the
needle will not go up and down).
2 Guide the thread around the bobbin
thread tension guide into the tension
disk.
3 Thread through the hole in the
bobbin from the inside to the outside.
Put the bobbin on the bobbin winder
spindle with the free end of the
thread coming out at the top.
4 Slide the bobbin winder spindle to the
right.
NOTE: Do not move the bobbin
winder spindle while the machine is
running.
5 With the free end of the thread held
in your hand, press the foot control.
Stop the machine when the bobbin
has made a few turns, and cut the
thread as illustrated.
6 Press the foot control again. When
the bobbin is fully wound, it will stop
automatically. Slide the bobbin winder
to its original position by moving the
spindle to the left, and cut the thread
as illustrated.
7 Push in the handwheel.
To use the vertical spool pin, set the felt
and the spool as shown above.
a Vertical spool pin
b Spool pin felt
c Spool pin hole
a
b
c
3
1
3
1
4
2
5
6
7
2
13
Placing the bobbin
Turn off the power switch
1 Place the bobbin in the bobbin
case with the thread pulling off as
illustrated.
2 Guide the thread into the front
notch (a) on the front side of the
bobbin case. Draw the thread to the
left, sliding it between the tension
spring blades.
3 Continue to draw the thread lightly
until the thread slips into the side
notch (b).
4 Pull out about 10 cm (4”) of thread.
Attach the bobbin cover. Check the
threading by referring to the chart
shown on the bobbin cover.
a
b
1
2
3
4
14
Threading the Machine
Turn off the power switch
Make sure the presser foot is raised and
the needle is in the up position.
1 Bring the thread from the spool and
pass it through the thread guide.
Then draw it down along the right
slot.
2 Guide the thread around the bottom
of the thread guide plate.
3 Firmly draw the thread from right to
left over the take-up lever and down
into the take-up lever eye.
4 Slide the thread from the left behind
the needle bar thread guide.
5 Use the needle threader to thread
the needle (see page 15).
1
4
5
2
3
1
2
3
5
4
15
Needle threader
Turn off the power switch
1 Raise the needle to its highest position.
Lower the needle threader as far as it
will go. The hook comes through the
needle eye from behind.
2 Bring the thread from the left around
the guide and under the hook.
a
Guide
b Hook
3 Release the knob slowly while
holding the thread end with your
hand. A loop of the thread is pulled
through the needle eye.
4 Pull the loop of thread behind the
needle eye.
1
2
3
4
a
b
16
Bringing up the Bobbin
Thread
Turn off the power switch.
1 Raise the presser foot and hold the
needle thread lightly with your left
hand.
2 Turn the handwheel slowly toward
you one complete turn. Bring the
bobbin thread up by pulling the
needle thread as illustrated.
a Needle thread
b Bobbin thread
3 Pull 10 cm (4”) of both threads back
and under the presser foot.
a
b
1
2
3
17
Stretch stitches
Emerald 116
Emerald 122
Emerald 118
Stretch stitches
Stretch stitches
Stitches
18
Stitch selection
Raise the needle to its highest position.
Turn the stitch selection dial to set the
desired stitch pattern number at the
setting mark.
1 Stitch selection dial
2 Setting mark
NOTE: Always raise the needle above the
fabric and presser foot before you turn
the stitch selction dial.
Stitch Length
Turn the stitch length dial to set the
desired stitch length number at the
setting mark. The higher the number, the
longer the stitch.
The
mark shows the adjustment
range when sewing the buttonhole.
3 Stitch length dial
Set the stitch length dial at “stretch”
when sewing stretch stitches.
NOTE: Always raise the needle above the
fabric and presser foot before you turn
the stitch length dial.
3
1
2
2
3
2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Viking Emerald 116 Manuel utilisateur

Catégorie
Machines à coudre
Taper
Manuel utilisateur

dans d''autres langues