Pfaff classicstyle quilt 2027 Le manuel du propriétaire

ClassicStyle Quilt

2027

Owner´s manual

v. 1.0

This household sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be followed, including the

following:

Read all instructions before using this household sewing machine.

DANGER - To reduce the risk of electric shock:

• A sewing machine should never be left unattended when plugged in. Always unplug this sewing machine

from the electric outlet immediately after using and before cleaning.

• Always unplug before relamping. Replace bulb with same type rated 5 Watt.

WARNING - To reduce the risk of burns, À re,

electric shock, or injury to persons:

• Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or

near children or inÀ rm person.

• Use this sewing machine only for its intended use as described in this manual. Use only attachments

recommended by the manufacturer as contained in this manual.

• Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has

been dropped or damaged, or dropped into water. Return the sewing machine to the nearest authorised

dealer or service center for examination, repair, electrical or mechanical adjustment.

• Never operate the sewing machine with any air openings blocked. Keep ventilation openings of the

Sewing machine and foot controller free from the accumulation of lint, dust, and loose cloth.

• Keep À ngers away from all moving parts. Special care is required aro und the Sewing machine needle.

• Always use the proper needle plate. The wrong plate can cause the needle to break.

• Do not use bent needles.

• Do not pull or push fabric while stitching. It may deÁ ect the needle causing it to break.

• Switch the sewing machine off (“0”) when making any adjustment in the needle area, such as threading

needle, changing needle, threading bobbin, or changing presser foot, etc.

• Always unplug the sewing machine from the electrical outlet when removing covers, lubricating, or when

making any other user servicing adjustments mentioned in the instruction manual.

• Never drop or insert any object into any opening.

• Do not use outdoors.

• Do not operate where aerosol (spray) products are being used or where oxygen is being administrated.

• To disconnect, turn all controls to the off (“0”) position, then remove plug from outlet.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

SAVE THESE INSTRUCTIONS

32

01

15

11

1413

9

12

8

7

6

4

5

10

0. Standard Presser Foot with IDT

820250-096

1. Fancy Stitch Foot with IDT

820253-096

2. Fancy Stitch Foot

820278-096

3. Blindhem/Overlock Foot with IDT

820256-096

4. Zipper Foot with IDT

820248-096

5. Buttonhole Foot

820295-096

6. Bulb Remover/Needle Plate Changer

820292-096

7. Buttonhole Guide

820294-096

8. Spool cap

93-036 048-44/000, 93-035 050-44/000, 93-036 049-44/000

9. Felt pad

93-033 064-06/000

10. Bobbins

412 76 79-01

11. Needle box

48-020 804-32/000

12. Edge Guide/Quilting Guide

820251-096

13. Second spool holder

93-033 063-44/000

14. Seam ripper

99-053 016-91/000

15. Brush

93-847 979-91/000

Presser feet (standard accessories)

For more information about accessories, please contact your PFAFF dealer.

The perfect sewing machine for quilting!

Congratulations!

You have purchased a top quality PFAFF® sewing/quilting machine with great quilt features.

ClassicStyle™ Quilt

2027

with its ease of use, selection of quilt stitches and practical features will make your

quilting a special experience.

To learn about your

ClassicStyle Quilt

2027

, follow the instructions for the

expression™

2028

.

Your

ClassicStyle Quilt

2027

has the same features as the

expression

2028

, except from some stitches and

accessories. In this manual other accessories are described, they are optional and can be purchased from your

Pfaff dealer.

16

15

14

13

12

11

10

9

8

7

6

5

4

32

1

18

17

19

20

33

32

31

29

28

27

26

25

24

2322

21

30

1 -/+ button A (stitch width/pattern

width controls)

2 -/+ button B (stitch length/pattern

length controls)

3 -/+ button C (stitch density/balance

controls)

4 Carrying handle

5 Handwheel

6 Direct selection buttons

7 Stitch selection button

8 Connection socket “lead cord”

9 Connection socket “foot control”

10 Master switch

11 Base plate

12 Removable accessory tray

13 Presser foot holder with presser foot

14 Integrated dual feed/IDT

15 Integrated needle threader

16 "Reverse sewing” button

17 Threading slots

18 Needle thread tension

19 Take-up lever

20 Presser foot lifter

21 Thread guide

22 Spool holder with spool cap

23 Hole for second spool holder

24 Lid with stitch chart

25 Bobbin winder

26 Bobbin door

27 Free arm

28 Sewing bulb (max. 5 W)

29 Thread cutter

30 “Pattern mirror” button/”Lock”

button

31 Thread take-up

32 Needle holder with retaining (set)

screw

33 Needle plate

Parts of the sewing machine

Congratulations! You have purchased a high-

quality product that offers unique advantages.

It features the very latest in design and

technology, and this instruction book is just as

uncomplicated as your PFAFF sewing machine.

If you now take time enough to study the

instruction book, nothing can go wrong. After

all, this is the only way to learn all the things

the machine can do, and to make full use of

them.

If you have any further questions, that is no

problem! Your PFAFF dealer will be at your

service with any help or advice you need.

So now you can get started! We wish you many

enjoyable hours of creating your fashion ideas.

Modern, uncomplicated

Sewing by push-button control

1:2

Introduction

TABLE OF CONTENTS

1. Introduction

Utility stitches expression 2028 1:4

Utility stitches expression 2028 1:5

Decorative stitches 1:6

2. Preparations

Carrying case 2:1

Lid 2:1

Electrical connection 2:2

Connecting the foot control 2:2

Voltage Switch 2:2

Accessory tray 2:3

Removing the accessory tray 2:3

Bobbin winding 2:4-5

Thread tension 2:6

Inserting the bobbin 2:6

Threading the needle 2:7

Integrated Needle threader 2:8

Presser foot lifter 2:8

Drawing-up the bobbin thread 2:9

Bobbin thread 2:9

Thread cutter 2:9

Changing the presser foot 2:9

Setting the needle thread tension 2:10

Winding a bobbin through the needle 2:10

Changing the needle 2:12

Threading the twin needle: 2:12

The IDT (Integrated Dual Feed) 2:13

Lowering the feed dog 2:13

3. Sewing

Stitch selection 3:1

Altering stitches 3:1

Altering the stitch width 3:1

Altering the needle position 3:1

Altering the pattern width e.g. Stitch 25 3:2

Altering the stitch/pattern length 3:2

Altering the stitch density 3:2

Balance 3:3

Reverse sewing 3:3

“Pattern mirror” 3:3

"Lock" button 3:4

Twin needle 3:4

Explanation of the sewing

recommendations table 3:6

Sewing in zippers 3:6

Basting stitch 3:7

Top stitching 3:7

Blind hem stitch 3:8

Overlock stitches 3:9

Free Motion Sewing 3:10

Bridging stitch 3:11

Cross hem stitch 3:11

Rolled hem with hemmer No. 7 3:12

Shell edging 3:12

Buttonholes 3:13

Inserting the sensormatic buttonhole

guide: 3:13

Attaching buttonhole foot 3:13

Fully automatic buttonhole 3:13

Semi-automatic buttonhole 3:14

Manual buttonhole 3:15

1:3

Introduction

Buttonhole with gimp thread 3:16

Sewing on buttons 3:17

Buttonhole tips: 3:17

General notes on decorative sewing 3:18

Changing the pattern width 3:18

Changing the pattern length 3:18

Free motion embroidery 3:19

Tapering 3:19

Quilt stitch 3:19

Cross-stitch 3:20

Hemstitching 3:20

4. Maintenance

Changing the needle plate 4:1

Cleaning 4:1

Changing the light bulb 4:2

Sewing problems and their solutions 4:3

1:4

1234567890 11121310

Introduction

Utility stitches expression™ 2028

Stitch No. Description Application Presser-

foot

1 Straight stitch For seaming and topstitching up to 6 mm. 13 needle positions

available for edgestitching or sewing in zippers.

0

2 Stretch triple straight

stitch

For reinforced seams such as trousers, under arm seams or

decorative topstitching. With 13 needle positions.

1

3 Zigzag stitch, Center

needle position

For À nishing seams on fabrics, applique, and inserting lace. 0

4 Elastic stitch Strong stitch for seam À nishes, sewing elastic, darning tears, and

patches.

0

5 Blind hem stitch For securing hems invisibly on woven fabrics 3

6 Elastic blind hem stitch For securing hems invisibly and À nishing the edge on stretch

fabrics.

3

7 Closed overlock stitch

For hemming and overlapping stretch fabrics in one operation

. The

closed seam prevents fabric edges from fraying.

3

8 Bridging stitch For bridging, decorative hemstitching and crazy quilting. 0

9 Linen buttonhole Buttonhole for blouses, shirts and linen. 5

0 Button attaching program For two-hole or four-hole buttons. 2

10 Basting stitch For basting project pieces together. 1

11

Zigzag stitch Right/Left

needle position

For applique, couching over cords and creating eyelets. 3

12

Lightning stretch stitch For joining light weight stretch fabrics and decorative

embellishment

1

13

Decorative elastic stitch For joining overlapped seams on bulky fabrics such as leathers

and terry cloth.

0

1:5

17 18 19 20 21 22 23 24 2514 15 16

26

Introduction

Utility stitches expression 2028

Stitch No. Description Application Presser-

foot

14 Lightning stretch stitch For joining light weight stretch fabrics and decorative

embellishment.

1

15 Stretch triple zigzag stitch Elastic stitch for decorative hems and topstitching. 1

16 Overlock stitch For joining and overcasting stretch fabrics in one operation. 3

17 Honeycomb stitch Elastic, decorative stitch for ornamental hem À nishing on

stretch fabric, for decorative elastic application and sewing

with elastic thread in the bobbin.

0

18 Cross hem stitch Provides a highly elastic decorative seam for hems on

sportswear and casual wear.

0

19 Closed overlock stitch For joining and overcasting woven fabric and easily fraying

fabrics in one operation. The overcast edge thread prevents the

fabric edges from fraying.

3

20 Pullover stitch Join and overcast open knit fabrics and jersey. 3

21 Light-knit fabric patching

stitch

For sewing and patching light knit wear (undergarments etc.) 3

22 Cross stitch Classic decorative stitch for garments, linen and kitchen

towels.

1

23 Cross stitch Classic decorative stitch for garments, linen and kitchen

towels.

1

24 Hem stitching For ornamental hem stitching. Can be used with wing needle. 1

25 Hem stitching For ornamental hem stitching. Can be used with wing needle. 1

26 Hem stitching For ornamental hem stitching. Can be used with wing needle. 1

1:6

34 35 36

39

40 42

43

53

59

46

60

41

48 49 51

54

52

38

55

63

44

45

37

28

27

29

30 31 32 33

67

47

50

64

66

65

61585756 62

68

Introduction

Decorative stitches expression 2028

Quilt stitches 2028

2:1

Preparations

The stitches of the sewing machine are illustrated on the inside of the lid.

Carrying case

Place the enclosed lead cord, the foot control and instruction

book into the compartment of the carrying case.

Lid

Open the folding lid (24) upwards.

2. Preparations

2:2

220 V... 240 V

120 V

Preparations

Electrical connection

Connect the lead cord between the socket (8) of the sewing

machine and the wall outlet.

For the USA and Canada:

This sewing machine has a polarized plug (one blade wider

than the other). To reduce the risk of electric shock, this plug

is intended to À t in a polarized outlet only one way. If the plug

does not À t fully in the outlet, reverse the plug. If it still does

not À t, contact a qualiÀ ed electrician to install the proper outlet.

DO NOT modify the plug in any way!

Connecting the foot control

Connect the plug of the foot control to the connection socket (9)

of the sewing machine.

The sewing speed is controlled by pressing the foot control.

The foot control type AT 0070 has to be used for this sewing

machine.

Main switch

When the main switch (10) is switched on (switch function I)

the sewing lamp lights up and program No. 1 is indicated in the

expression window.

The sewing machine is now ready to function.

"0" = OFF

"I" = ON

Voltage Switch

220 - 240V / 120V

The sewing machine is set to the voltage 220 - 240V. To change

the voltage to 120V (US/Canada), you must set the voltage

switch on the underside of the machine to 120 V.

If you are unsure of the correct voltage for your country, please

check with your authorized sewing machine dealer or local

electrical authorities before plugging in your machine.

2:3

Preparations

Accessory tray

Open the accessory tray by placing your left index À nger on the

ridged area on the left of the lid and open the lid upwards and

towards you.

Arranging the accessories

The standard accessories are marked with numbers. Arrange

the parts in the respective compartments of the accessory tray.

Note: Some fabrics have a lot of excess dye which can cause

discoloration on other fabric but also on your sewing machine.

This discoloring may be very difÀ cult or impossible to remove.

Fleece and denim fabric in especially red and blue often contain

a lot of excess dye.

If you suspect that your fabric/ready-to-wear garment

contains a lot of excess dye, always pre-wash it before sewing/

embroidering to avoid the discoloring.

Removing the accessory tray (free arm)

In order to sew using the free arm, swing the accessory tray

to the left and lift it upwards out of the hole. When replacing

the tray, make sure it is Á ush with the free arm of the sewing

machine.

2:4

B

A

C

Preparations

Preparing the machine for bobbin winding

Place an empty bobbin so that the black pin of the bobbin

winder snaps into the slot of the bobbin. The Pfaff logo is facing

up.

Push the bobbin to the right.

Note: The bobbin can only be wound if it is moved fully to the right

Winding the bobbin from the spool pin

Place the sewing thread on the spool pin. To obtain free

movement of the thread and hold the thread spool À rmly, À t a

spool cap of the right size for the thread spool.

Threading

Place the thread into guide A from the front and pull it counter

clockwise around the pre-tension device B. Make sure the

thread is pulled securely inside the pre-tension device for

correct thread tension. Pull the thread under the thread guide

C (from back to front). Wind the thread tail around the bobbin

several times in a clockwise direction.

Turn on the machine

Hold the end of the thread À rmly and press the foot control. As

soon as the bobbin is full, the winding action will be stopped

automatically. Push the bobbin to the left, cut the thread and

remove bobbin from the winder.

2:5

C

B

A

Preparations

Winding from the second spool pin

Insert the second spool pin in the hole provided.

Threading

Thread as shown on page 2:4.

Turn on the machine

Hold the end of the thread À rmly and press the foot control. As

soon as the bobbin is full, the winding action will be stopped

automatically. Cut the thread, push the bobbin to the left and

remove bobbin from the winder.

Bobbin door

Switch off the main switch

Hold the bobbin door (26) at the left side and open it towards

the front

Taking out the bobbin case

Lift the latch of the bobbin case and pull the bobbin case out of

the machine. Release the latch and take the empty bobbin out of

the bobbin case.

2:6

A

B

Preparations

Thread tension

To obtain a perfect seam appearance and durability make sure

the needle thread tensions is correctly adjusted, i.e. the threads

evenly meet between the two fabric layers.

The following is valid for general sewing:

Bobbin thread is visible on the top side of the fabric:

The needle thread tension is too tight.

The thread tension must be corrected.

Top thread is visible on the underside of the fabric:

The needle thread tension is too loose.

The thread tension must be corrected.

For decorative stitches and buttonholes the top thread should

be visible on the underside of the fabric.

Inserting the bobbin

Insert the full bobbin (with the Pfaff logo facing towards

the bobbin case) in the bobbin case. When doing so, pull the

thread through slot A, then under tension spring B until it

rests in the opening (see arrow).

Check:

When you look at the bobbin and pull the thread, the bobbin must

turn clockwise

Inserting the bobbin case

Lift latch E and push the bobbin case fully onto pin C of

the sewing hook. Opening D of the bobbin case must face

upwards.

Check:

Pull the bobbin thread sharply. The bobbin case must not fall out

of the hook.

2:7

A

B

C

D

Preparations

Threading the needle

Switch off the main switch

Raise the presser foot lifter (20). Place the thread on the

spool pin and À t a spool cap of the right size.

Using both hands, pull the thread into thread guide A from

the front. Place the thread from right to left into the pre-

tension device B. Now pass it through the left threading

slot downwards. Pull the thread around the stop C in the

right threading slot and upwards to the take-up lever (19).

The thread must be pulled into the take-up lever from left

to right. Pass the thread downwards in the right-hand

threading slot. Pull the thread from the side behind one of

the two thread guides D.

To thread the needle, please refer to the next page.

2:8

E

F

Preparations

Integrated Needle threader

In order to make threading the needle easier and quicker, use

the Pfaff Integrated Needle threader. Lower the presser foot.

Press the threader down with the handle. Threader hook F

swivels through the needle eye. Place the thread over hook E

and under the thread hook F and hold the end of the thread

taut. Reduce the pressure so that the needle threader slowly

moves upwards. At the same time the threader hook swivels

out of the needle eye and pulls the thread through the eye.

Release the end of the thread so a thread loop forms behind the

needle. Release the threader and pull the rest of the thread end

through the needle eye.

Presser foot lifter

The presser foot is raised or lowered with the presser foot lifter

(20).

2:9

Preparations

Drawing-up the bobbin thread

Raise the presser foot. While holding the end of the needle

thread, press the foot control so the needle moves down and

up. Pull the needle thread to draw up the bobbin thread.

Bobbin thread

Close the bobbin door (26) and pull the thread under the

presser foot to the left

Thread cutter

Pull the thread from the back to the front over the thread cutter

(29).

Removing the presser foot

Switch off the main switch

Press the front part of the presser foot upwards and at the same

time the rear part downwards until it disengages from the

presser foot holder (13).

2:10

Preparations

Attaching the presser foot

Place the presser foot under the presser foot holder (13), so that

when the presser foot lifter (20) is lowered, the pins of the foot

engage in the presser foot holder.

Check:

Please check that the presser foot is properly attached by raising the

presser foot lifter.

Setting the needle thread tension

Set the required amount of the needle thread tension (18) using

the markings on the tension dial.

The normal setting for sewing is 4 - 5. For decorative sewing,

darning and buttonhole sewing 3.

Winding a bobbin through the needle

It is possible to wind bobbins even when the machine is fully

threaded. Raise the presser foot lifter (20) to the top position.

Pull the needle thread underneath the presser foot and upward

through the right-hand threader slot (17).

La page charge ...

Pfaff classicstyle quilt 2027 Le manuel du propriétaire

Ce manuel convient également à

Pfaff classicstyle quilt 2027 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents