RIDGID DV05000 Mode d'emploi

Marque: RIDGID

Modèle: DV05000

Catégorie: Aspirateurs

Taper: Mode d'emploi

Ce manuel convient également à

DV05000

5 U.S. GALLON / 18 LITER

ASH VAC

Part No. SP6957 Printed in China

OWNER’S MANUAL

SAVE THIS MANUAL FOR FUTURE REFERENCE

WARNING:

To reduce the risk of injury, the user must read and understand the owner’s manual

before using this product.

Thank you for buying a RIDGID product.

QUESTIONS OR INFORMATION CONTACT US AT

1-800-4-RIDGID (1-800-474-3443) from the US and Canada

01-800-701-9811 from Mexico

www.RIDGIDvacs.com

• Español - página 17

• Français - page 33

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 1

This vacuum is intended to pick up

COLD ash from fireplaces, grills, ovens,

ashtrays, etc. Read and understand this

manual and all labels on this ash vac

before operating.

• Use only as described in this manual.

• Do not pick up anything that is burning

or smoking, like cigarettes, matches or

hot, glowing, or burning embers. Pick up

cold ash only. Be aware that ash/embers

can be hot for days after use.

Table of Contents

IMPORTANT SAFETY INSTRUCTIONS

Safety is a combination of using common

sense, staying alert, and knowing how your

Vacuum Cleaner (“Vac”) works.

Safety Signal Words

DANGER: Indicates a hazardous

situation which, if not avoided, will result

in death or serious injury.

WARNING: Indicates a hazardous

situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a hazardous

situation which, if not avoided, could

result in minor or moderate injury.

When using your Vac, always follow basic

safety precautions including the following:

WARNING

- To reduce the risk of fire, heat

damage, electric shock, or injury:

• Use caution when vacuuming materials

that appear to have cooled, but may

actually be hot inside. First check for

hot spots by raking through the

ashes/coals. Air flow created during

vacuuming may cause hot ash to

reignite. As you vacuum, constantly

check the nozzle, hose, drum, and

motor for excessive temperatures. If

you notice an increase in temperature,

turn off the vacuum immediately.

Unplug the vacuum and remove the

vacuumed material from the drum.

• The drum must be emptied and

cleaned after each use, and before

picking up other household debris.

• Allow the vacuum to cool before

storage, especially enclosed storage.

• Do not use paper dust bags.

• To reduce the risk of damage from

accidental hot ember pickup, do not

place the vacuum on surfaces

susceptible to heat damage, such as

carpeting, vinyl flooring, or wood

surfaces.

• Do not leave Vac running while

unattended - you may fail to notice

important signs indicating abnormal

operation such as loss of suction,

debris exiting exhaust, or abnormal

motor noises. Immediately stop using

Vac if you notice these signs.

Section Page

Important Safety Instructions . . . . . . . . . 2-4

Grounding Instructions . . . . . . . . . . . . . . . 5

Introduction . . . . . . . . . . . . . . . . . . . . . . . . 6

Unpacking and Checking

Carton Contents . . . . . . . . . . . . . . . . . . . 6

Vac Assembly . . . . . . . . . . . . . . . . . . . . . 7-9

Removal of Power Head Assembly . . . . 7

Caster Assembly . . . . . . . . . . . . . . . . . . 7

Power Head Assembly . . . . . . . . . . . . . . 8

Insert Locking Hose . . . . . . . . . . . . . . . . 8

Hose Assembly . . . . . . . . . . . . . . . . . . . 8

Hose Assembly for LED Lighted Nozzle 9

LED Lighted Nozzle . . . . . . . . . . . . . . . . 9

Section Page

Operation . . . . . . . . . . . . . . . . . . . . . . 10-11

Motor/Electrical. . . . . . . . . . . . . . . . . . . 10

Emptying the Vac Drum . . . . . . . . . . . . 11

Maintenance . . . . . . . . . . . . . . . . . . . . 12-13

HEPA Filter . . . . . . . . . . . . . . . . . . . . . . 12

Filter Removal and Installation . . . . . . . 12

Cleaning a Dry Cartridge Filter . . . . . . 13

Cleaning & Disinfecting the Ash Vac . . 13

Cord Maintenance & Storage. . . . . . . . 13

Ash Vac Storage. . . . . . . . . . . . . . . . . . 13

Casters . . . . . . . . . . . . . . . . . . . . . . . . . 13

Repair Parts . . . . . . . . . . . . . . . . . . . . 14-15

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 16

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 2

• Do not handle plug, switch, or the Vac

with wet hands.

• Do not pull or carry by cord, use cord

as handle, close a door on cord, or pull

cord around sharp edges or corners.

Do not run vac over cord. Keep cord

away from heated surfaces.

• Only use extension cords that are

intended for outdoor use, such as SJW

or SJTW. Use only three-wire outdoor

extension cords that have three-prong

grounding plugs and grounding

receptacles that accept the vac's plug.

Extension cords in poor condition or

too small in wire size can pose fire and

shock hazards. To reduce the risk of

these hazards, be sure the cord is in

good condition and that liquid does not

contact the connection. Do not use an

extension cord with conductors smaller

than 16 gauge (AWG) in size.

To reduce power loss, use a 14 gauge

extension cord if 25 to 50 ft. (8 to 15 m)

long and 12 gauge for 50 ft. (15 m)

or longer.

• Connect only to a properly-grounded

outlet. See grounding instructions

• Do not put any object into ventilation

openings. Do not vacuum with any

ventilation openings blocked; keep free

of dust, lint, hair or anything that may

reduce air flow.

• Keep hair, loose clothing, fingers, and

all parts of body away from openings

and moving parts.

• To reduce the risk of falls, use extra

care when cleaning on stairs.

• To reduce the risk of back injury or

falls, do not lift a Vac that is heavy with

debris. Partially empty by scooping out

debris.

• To reduce the risk of personal injury or

damage to Vac, use only Ridgid

recommended accessories.

• To reduce the risk of eye injury, wear

safety eyewear. The operation of any

utility Vac can result in foreign objects

being blown into the eyes, which can

result in severe eye damage.

• Do not leave Vac when plugged in.

Unplug from outlet when not in use

and before servicing.

• Sparks inside the motor can ignite

flammable vapors or dust. To reduce

the risk of fire or explosion, do not use

near combustible liquids, gases, or

dusts, such as gasoline or other fuels,

lighter fluid, cleaners, oil-based paints,

natural gas, coal dust, magnesium

dust, grain dust, aluminum dust, or gun

powder.

• To reduce the risk of inhaling toxic

vapors, do not vacuum or use near

toxic or hazardous materials.

• To reduce the risk of electric shock,

do not expose to rain or allow liquid to

enter motor compartment. Store

indoors.

• This Ash Vac is not intended for use by

persons (including children) with

reduced physical, sensory, or mental

capabilities, or lack of experience and

knowledge, unless they have been

given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

• Do not allow to be used as a toy.

Close attention is necessary when

used by or near children.

• Do not use with a torn filter or without

filter and filter screen installed.

Dry debris ingested by the impeller

may damage the motor or be

exhausted into the air.

• Turn off Vac before unplugging.

• To reduce the risk of injury from

accidental starting, unplug power cord

before changing or cleaning filter.

• Do not unplug by pulling on cord.

To unplug, grasp the plug, not the cord.

• Do not use with damaged cord, plug or

other parts. If your Vac is not working

as it should, has missing parts, has

been dropped, damaged, left outdoors,

or dropped into water, call customer

service.

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 3

Observe the following warnings that

appear on the Lighted Nozzle (select

catalog numbers only).

Observe the following warnings that

appear on the Vacuum.

WARNING: Risk of Electric Shock.

For your own safety, read and

understand owner’s manual.

Do not run unattended. Do not pick

up toxic, flammable, or other

hazardous materials. Do not use

around explosive liquids or vapors.

To reduce the risk of electric shock,

do not use on wet surfaces. Do not

expose to rain. Store indoors.

This is a dry vacuum only; NEVER

vacuum liquids with this product.

WARNING: Risk of Fire and Heat

Damage.

This vacuum is intended to pick up

COLD ash from fireplaces, grills,

ovens, ash-trays, etc. Do not pick

up hot, glowing, or burning

ash/embers. Pick up cold ash only.

Be aware that ash/embers can be

hot for days after use. To reduce

the risk of damage from accidental

hot ember pickup, do not place the

vacuum on surfaces susceptible to

heat damage such as carpeting,

vinyl flooring, or wood surfaces.

Empty drum after each use.

Allow to cool before storing,

especially in enclosed spaces.

Do not use dust collection bags.

WARNING:

• Keep batteries out of reach of

small children. Consult a physician

immediately if a battery is swallowed;

severe burning or injury may occur.

• Battery contains Perchlorate

Material - Special handling may

apply. See www.dtsc.ca.gov/

hazardouswaste/perchlorate.

CAUTION:

•To reduce the risk of hearing damage,

wear ear protectors when using for

extended time or in a noisy area.

• For dusty operations, wear dust mask.

• Static shocks are common when the

relative humidity of the air is low.

Vacuuming fine debris with your Vac can

deposit static charge on the hose or

Vac. To reduce the frequency of static

shocks in your home or when using this

Vac, add moisture to the air with a

humidifier.

SAVE THIS MANUAL

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 4

Grounding Instructions

This appliance must be grounded.

If it should malfunction or break down,

ground ing provides a path of least

resistance for electric current to reduce

the risk of electric shock. This appliance

is equipped with a cord having an

equipment-grounding conductor and

grounding plug. The plug must be

inserted into an appropriate outlet that is

properly installed and grounded in

accordance with all local codes and

ordinances.

WARNING:

Improper connection of the

equipment grounding conductor

can result in a risk of electric shock.

Check with a qualified electrician or

service person if you are in doubt

as to whether the outlet is properly

grounded. Do not modify the plug

provided with the appliance - if it

will not fit the outlet, have a proper

outlet installed by a qualified

electrician.

This Vac is for use on a nominal 120-volt

circuit, and has a grounded plug that

looks like the plug shown. A temporary

adapter that looks like the adapter shown

may be used to connect this plug to a

2-pole receptacle, as shown. If a properly

grounded outlet is not available, the

temporary adapter should only be used

until a properly grounded outlet can be

installed by a qualified electrician.

Properly

Grounded

Outlet

Grounding

Prong

3-Prong

Plug

Make sure this is a

metal screw connected

to a known ground

Green

Grounding Lug

2-Prong Outlet

3-Prong Plug

Adapter

The green-colored rigid ear, lug, or the

like, extending from the adapter, must be

connected to a permanent ground such

as a properly grounded outlet box cover.

Whenever the adapter is used, it must be

held in place by a metal screw.

NOTE: In Canada, the use of a

temporary adapter is not permitted by

the Canadian Electrical Code.

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 5

Unpacking and Checking Carton Contents

Remove contents of carton. Check each

item against the Carton Contents List.

For questions or information contact us at

1-800-4-RIDGID (1-800-474-3443) from

the US and Canada 01-800-701-9811

from Mexico www.RIDGIDvacs.com.

If any parts are damaged or missing.

Carton Contents List

Key Description Qty.

A Ash Vac (5-Gallon/18 Liter) . . . . . . .1

B Casters . . . . . . . . . . . . . . . . . . . . . . .4

C Metal Cover . . . . . . . . . . . . . . . . . . .1

D HEPA Filter . . . . . . . . . . . . . . . . . . . .1

E Filter Screen . . . . . . . . . . . . . . . . . . .1

F Extension Nozzle . . . . . . . . . . . . . . .1

G Wand Nozzle . . . . . . . . . . . . . . . . . .1

H Locking Hose (metal lined) . . . . . . . .1

I Owner’s Manual . . . . . . . . . . . . . . . .1

Some items may come preassembled.

If they are not present in the carton check the

Vac power head to see if they are

preassembled.

Introduction

This Ash Vac is intended for household

use. It may be used for vacuuming of dry

debris, including cold ash from fireplaces,

grills, ovens, ash-trays, etc. It should not

be used to pick up liquids.

Read this owner’s manual to familiarize

yourself with the product features and to

understand the specific usage of your

new Vac.

Select Catalog Numbers May Also

Include:

J* Locking Hose (metal lined)

with LED Lighted Nozzle . . . . . . . . .1

* If this item is included with your purchase, it wil appear on the contents list found on the product

packaging.

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 6

Caster Assembly

1. After removal of the power head from

drum. Turn the dust drum upside

down.

2. Insert the caster stem into the socket

of the caddy, as shown (4 places).

3. Push on the caster until the caster

stem is inserted all the way into the

socket.

4. Turn the drum upright.

Caster

Stem

Socket

Drum

Vac Assembly

Removal of Power Head Assembly

1. Grasp the drum latches on both the

right and left side of the Vac.

2. Slowly pull the bottom of the latches

up and away from the drum.

3. The top of the latches will then be free

of the power head.

4. Lift the power head from the drum and

place it on a dry surface.

WARNING: For your own safety,

never connect plug to power source

outlet until all assembly steps are

complete and you have read and

understood the safety and operation

instructions. Do not operate Vac

with any parts damaged or missing.

SNAP

DOWN

LATCH

Latches

ROTATE

LATCH

Power Head Assembly

Lip

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 7

Vac Assembly (continued)

Insert Locking Hose

NOTE: Use ONLY the metal lined hose

and metal accessories provided with this

Ash Vac.

1. Align hose tabs with inlet and insert

the locking end of the hose into the

inlet of the Vac drum, as shown.

2. Rotate the hose clockwise to lock into

place.

3. To remove the hose from the Vac,

rotate the locking hose counter-

clockwise and pull the hose out of the

Vac inlet.

Inlet

Locking Hose

(Metal Lined)

ROTATE HOSE

CLOCKWISE

TO LOCK

Hose

Locking

End

Hose Assembly

1. Slide the round end of the extension

nozzle into the smaller tapered end of

the wand nozzle.

2. Attach wand nozzle to hose end.

Wand

Nozzle Extension

Nozzle

Power Head Assembly

1.Line up front of power head assembly

with vacuum port located on the front

of the drum, as shown.

2.Place power head assembly on top of

drum.

3. Be sure power head assembly

completely covers the top of the drum

so leakage does not occur.

4. Rotate the latches on each side of the

drum, positioning the latch hooks over

the lip of the power head assembly.

5. Snap down the bottom edge of the

latches to secure the power head

assembly to the drum.

Vacuum

Port

Power Head

Assembly

Lip

ROTATE

LATCH

SNAP

DOWN

LATCH

Power Head

Assembly Latch

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 8

LED Lighted Nozzle

1. Press button to active LED light while

vacuuming.

2. Slide switch forward to lock the LED

light in the ON position.

3. Slide switch back to the OFF position

after use.

4. To access batteries, remove battery

access panel screw, then remove the

four screws from the LED assembly,

releasing the switch button module.

The two batteries are located under

the switch button module. Dispose of

batteries in the proper waste disposal

container.

5. The LED light uses two CR2016

lithium batteries that are replaceable.

LED Button

LED

Assembly

Switch

Button

Module

CR2016

Lithium

Batteries

(2)

Battery

Access

Panel

Screw (1)

Screws (4)

LED

Assembly

WARNING:

• Keep batteries out of reach of

small children. Consult a

physician immediately if a battery

is swallowed severe burning or

injury may occur.

• Battery contains Perchlorate

Material - Special handling may

apply. See www.dtsc.ca.gov/

hazardouswaste/perchlorate.

Vac Assembly (continued)

Hose Assembly for LED Lighted

Nozzle (For Select Catalog Numbers

Only)

1. Slide the round end of the extension

nozzle into the smaller tapered end of

the wand nozzle.

2. Loosen the two LED assembly screws,

located at the bottom of the LED

Lighted Nozzle.

3. Slide the wand nozzle through the

LED assembly and into the rubber

hose fitting.

4. Retighten the two LED assembly

screws to secure the LED assembly to

the hose assembly.

LED Lighted

Nozzle

Screws (2)

Wand Nozzle

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 9

Operation

WARNING: To reduce the risk of fire, explosion, or damage to Vac:

• Do not leave Vac running while unattended - you may fail to notice

important signs indicating abnormal operation such as loss of suction,

debris exiting the exhaust, or abnormal motor noises. Immediately stop

using Vac if you notice these signs.

• Do not leave Vac plugged in when not in use.

• The vacuum must be emptied after every use of ash pickup.

• Sparks inside the motor can ignite airborne flammables. Do not operate

Vac near flammable liquids or in areas with flammable gases, vapors, or

explosive/airborne dust. Flammable liquids, gases, and vapors include:

lighter fluid, solvent-type cleaners, oil-based paints, gasoline, alcohol, and

aerosol sprays. Explosive dusts include: coal, magnesium, aluminum,

grain, and gun powder.

• Do not vacuum up explosive dusts, flammable liquids, or hot ashes.

WARNING: To reduce the risk of electric shock or injury:

• Do not expose to rain or allow liquid to enter motor compartment.

Store indoors.

• Do not handle plug, switch, or Vac with wet hands.

• Unplug Vac before servicing. If your Vac is not working as it should, has

missing parts, has been dropped, damaged, left outdoors, or dropped into

water, return it to an authorized service center or call customer service.

• When using an extension cord, use only outdoor-rated cords that are in

good condition. Do not allow the connection to come into contact with

liquid.

After you plug the power cord into the

outlet, turn the unit on by pushing the

switch from position "O" to position "l".

The symbols used on the switch actuator

are international "On & Off" symbols.

=OFF =ON

"OFF"

"ON"

Motor/Electrical

This Ash Vacuum is rated for use with

120 volt 60 Hz supply. The Vac is

equipped with a thermal protection cutoff

switch which will remove power from the

vacuum motor if excessively high

operating temperatures are detected.

This condition may arise as the result

of a blocked vacuum passage, or clogged

filter. If a thermal trip takes place,

immediately toggle the vacuum’s switch

to OFF, unplug the unit and inspect for

an airflow blockage in the hose and verify

the condition of the filters (see

Maintenance). Clean or replace the filters

as required. The vacuum will require

several minutes to cool down to a safe

operating temperature. When this

temperature is attained, the thermal

switch will automatically reset and the

vacuum will be able to be used in the

normal manner.

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 10

Operation (continued)

NOTE: Do not store the vacuum

immediately after ash removal or other

use in a confined area or enclosed space.

Allow the power head to cool and remove

ash from drum before storage.

1. Grasp the drum latches on both side

of the power head.

2. Slowly pull up on the drum latches,

away from the drum.

3. The top of the latches will be free of

the power head.

4. Lift up on the power head and set it

on a clean dry area while emptying the

drum or changing the filter.

5. Be sure the ash is cool prior to

dumping the contents into the proper

waste disposal container.

WARNING: To reduce the risk of

injury from accidental starting,

unplug power cord before emptying

the Vac drum.

Emptying the Vac Drum

CAUTION: To reduce the risk of

hearing damage, wear ear protectors

when using the Vac for extended

hours or when using in a noisy area.

Drum

PULL

LATCH

UP AND

AWAY

ROTATE

LATCH

DOWN

ROTATE

LATCH

DOWN

PULL

LATCH

UP AND

AWAY

Latch

Drum

Cold Ash

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 11

HEPA Filter

Filter

Screen

Raised Lip

Maintenance

HEPA Filter

Your HEPA Filter should be cleaned often

to maintain peak Vac performance.

IMPORTANT: It is very important that the

screen filter is installed prior to use.

NOTE: The HEPA Filter is made of high

quality material designed to stop dust and

smaller particles. Handle the HEPA Filter

carefully when removing to clean or

installing a new HEPA Filter. Creases in

the HEPA Filter pleats may occur from

installation but creases will not affect the

performance of the HEPA Filter.

Filter Removal and Installation

Filter Removal:

1. Rotate the filter screen/HEPA Filter

counter-clockwise.

2. Remove the HEPA Filter from the filter

screen.

NOTE: The filter screen should be

cleaned with a brush.

3. Check the motor inlet filter, clean or

replace, if necessary.

Power

Head

Assembly

Filter

Screen

HEPA

Filter

Motor

Inlet

Filter

Metal

Cover

WARNING: To reduce the risk of

injury from accidental starting,

unplug power cord before changing

or cleaning the Filter.

Filter Installation:

1. Replace motor inlet filter.

2. Replace the HEPA Filter into the filter

screen.

NOTE: Be sure to orient the HEPA Filter

and the filter screen in the correct

position, as shown. The filter screen has

a raised lip on the inside of the screen to

hold it in place.

3. Rotate the filter screen/HEPA Filter

clockwise onto the power head metal

cover.

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 12

Ash Vac Storage

Before storing your Vac, the drum should

be emptied and cleaned. Wrap the hose

around the top of the cooled power head

assembly, positioning the hose under the

handle, as shown. Accessories should be

kept in the same area as the Vac so they

can be readily available. The Vac should

be stored indoors.

Casters

If your casters are noisy, you may put a

drop of oil on the roller shaft to make

them quieter.

Cleaning A Dry Cartridge Filter

NOTE: For best cleaning results due to

accumulated dust, clean the filter in an

open area. Cleaning SHOULD be done

outdoors and not in the living quarters.

1. Light cleaning of some dry debris from

the Filter can be accomplished without

removing the Filter from the Vac.

Simply slap your hand on top of the

handle while the Vac is turned off.

2. Remove Filter from Vac. Gently tap the

Filter against the inside wall of your

drum, or against the floor, and the

debris will loosen and fall.

Cleaning and Disinfecting the

Ash Vac

To keep your Vac looking its best, clean

the outside with a cloth dampened with

warm water and mild soap.

To clean the drum:

1. Dump debris out.

2. Wash drum thoroughly with warm

water and mild soap.

3. Wipe out with dry cloth.

Cord Maintenance & Storage

When vacuuming is complete, unplug the

cord and wrap it around the power head

handle. If the power cord is damaged,

it must be replaced by the manufacturer or

their service agent or by similarly qualified

personnel to reduce the risk of accident.

Accessories can be stored on the rear

power head or on the caddy base.

Maintenance (continued)

WARNING: To assure product

SAFETY and RELIABILITY, any other

maintenance, repairs and adjustments

should be performed by Authorized

Service Centers, always using RIDGID

replacement parts.

Accessory

Storage

Cord

Storage

Power

Head

Assembly

Caddy Base

Accessories

Hose Wrap

Area

Hose

- or -

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 13

Repair Parts

RIDGID 5 Gallon / 18 Liter Ash Vac

Model Number DV05000

RIDGID parts are available on-line at www.RIDGIDparts.com

Always order by Part Number - Not by Key Number

Key No. Part No. Description

1 836247 Handle, Carry

2 836248 Switch, Toggle

3 836265 Power Cord

4 836375 Drum Assembly (Includes Drum, Drum Inlet,

Drum Latches, & Caddy)

5 836264 Casters (Set of 4)

6 836257 Metal Cover

7 VF1500 HEPA Media Filter w/ Motor Inlet Filter

8 836270 Metal Filter Screen

9 836276 Extension Nozzle

10 836275 Wand Nozzle

11 836277 Locking Hose (Metal Lined)

12 836279 LED Lighted Nozzle Assembly

(Select Catalog Numbers Only)

13 SP6957 Owner’s Manual

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 14

Repair Parts (continued)

RIDGID 5 Gallon / 18 Liter Ash Vac

Model Number DV05000

RIDGID parts are available on-line at www.RIDGIDparts.com

Select Catalog Numbers

Only:

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 15

Part No. SP6957 Form No. SP6957-2 Printed in China 05/16

QUESTIONS OR INFORMATION CONTACT US AT

1-800-4-RIDGID (1-800-474-3443) from the US and Canada

01-800-701-9811 from Mexico

www.RIDGIDvacs.com

Please have your Model Number and Serial Number on hand when calling.

Stock No. DV0500 / DV0510

Model No. DV05000

Serial Number

Model and serial numbers may be found on the top of the motor cover.

You should record both model and serial numbers in a safe place for future use.

c 2016 Emerson

• What is covered

RIDGID®Vacs are warranted to be free of defects in workmanship and material.

• How long coverage lasts

This warranty lasts for the lifetime of the RIDGID®Vac.

• How to obtain service

To obtain the benefit of this warranty, deliver via prepaid transportation the complete product to

RIDGE TOOL COMPANY, Elyria, Ohio, or any authorized RIDGID®INDEPENDENT SERVICE

CENTER. Pipe wrenches and other hand tools should be returned to the place of purchase.

• What we will do to correct problems

Warranted Vacs will be repaired or replaced, at Ridge Tool Company's option, and returned at no

charge; or, if after three attempts to repair or replace during the warranty period the Vac is still

defective, you can elect to receive a full refund of your purchase price.

• What is not covered

Failures due to misuse, abuse or normal wear and tear are not covered by this warranty. RIDGE

TOOL COMPANY SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES.

• How local laws relate to the warranty

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation or exclusion may not apply to you. This warranty gives you specific rights, and you

may also have other rights which vary from state to state, province to province, or country to

country.

• No other express warranty applies

This FULL LIFETIME WARRANTY is the sole and exclusive warranty for RIDGID®Vacs.

No employee, agent, dealer, or other person is authorized to alter this warranty or make any other

warranty on behalf of Ridge Tool Company.

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 16

DV05000

ASPIRADORA DE CENIZA

DE 5 GALONES EE.UU./18 LITROS

MANUAL DEL USUARIO

GUARDE ESTE MANUAL PARA REFERENCIA FUTURA

Gracias por comprar un producto RIDGID.

¿PREGUNTAS O COMENTARIOS? COMUNÍQUESE CON NOSOTROS EN

1-800-4-RIDGID (1-800-474-3443) desde los EE.UU. y Canadá

01-800-701-9811 desde México

www.RIDGIDvacs.com

No. de pieza SP6957 Impreso en China

ADVERTENCIA:

Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual del operador

antes de utilizar este producto.

•Français - page 33

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 17

Instrucciones de seguridad importantes . . . . . 18-20

Instrucciones de conexión a tierra . . . . . . . . . . . 21

Introducción . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Comprobación del contenido

de la caja de cartón. . . . . . . . . . . . . . . . . . . . . . 22

Ensamblaje de la aspiradora . . . . . . . . . . . . . 23-25

Remoción del ensamblaje del cabezal

del motor. . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Ensamblaje de las ruedecillas . . . . . . . . . . . . . 23

Ensamblaje del cabezal del motor . . . . . . . . . . 24

Inserción de la manguera de fijación . . . . . . . . 24

Ensamblaje de la manguera . . . . . . . . . . . . . . . 24

Ensamblaje de la manguera para la boquilla

con iluminación LED . . . . . . . . . . . . . . . . . . 25

Boquilla con iluminación LED . . . . . . . . . . . . . 25

Funcionamiento. . . . . . . . . . . . . . . . . . . . . . . . 26-27

Funcionamiento del motor/eléctrico . . . . . . . . 26

Vaciado del tambor de la aspiradora . . . . . . . . 27

Mantenimiento . . . . . . . . . . . . . . . . . . . . . . . . 28-29

Filtro HEPA . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Remoción e instalación del filtro . . . . . . . . . . . 28

Limpieza de un filtro de cartucho sucio . . . . . . 29

Limpieza y desinfección de la aspiradora

de ceniza . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Mantenimiento y almacenamiento

del cable de alimentación . . . . . . . . . . . . . . 29

Almacenamiento de la aspiradora de ceniza . . 29

Ruedecillas. . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Piezas de repuesto . . . . . . . . . . . . . . . . . . . 30-31

Garantía . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

INSTRUCCIONES DE SEGURIDAD IMPORTANTES

La seguridad es una combinación de sentido común,

permanecer alerta y saber cómo funciona la

aspiradora (“la aspiradora”).

Palabras de señal de seguridad

PELIGRO: indica una situación peligrosa que,

si no se evita, causará la muerte o lesiones graves.

ADVERTENCIA: indica una situación peligrosa que,

si no se evita, podría causar la muerte o

lesiones graves.

PRECAUCIÓN: indica una situación peligrosa

que, si no se evita, pudiera causar lesiones leves

o moderadas.

Cuando utilice la aspiradora, siga siempre las

precauciones básicas de seguridad, incluyendo

las siguientes:

ADVERTENCIA

– Para reducir el riesgo de incendio, sacudidas

eléctricas o lesiones:

Esta aspiradora está diseñada para recoger cenizas

FRÍAS de chimeneas, parillas, hornos, ceniceros, etc.

Lea y entienda este manual y todas las etiquetas que se

encuentran en esta aspiradora antes de utilizarla.

• Utilice la aspiradora únicamente de la manera que se

describe en este manual.

• No recoja nada que esté ardiendo o humeando,

como cigarrillos, fósforos o brasas que estén

calientes, al rojo o ardiendo. Recoja sólo cenizas

frías. Tenga presente que las cenizas/brasas pueden

estar calientes durante varios días después del uso.

• Tenga precaución cuando aspire materiales que

parezcan haberse enfriado, pero que en realidad

pueden estar calientes en su interior. Compruebe

primero si hay puntos calientes rastrillando a través

de las cenizas/ascuas. El flujo de aire creado durante

la operación de aspiración puede hacer que la ceniza

caliente se reincendie. Mientras limpia con la

aspiradora, compruebe constantemente la boquilla,

la manguera, el tambor y el motor para determinar si

hay temperaturas excesivas. Si observa un aumento

de la temperatura, apague de inmediato la

aspiradora. Desenchufe la aspiradora y saque del

tambor el material aspirado.

• El tambor se debe vaciar y limpiar después de cada

uso, y antes de recoger otros residuos domésticos

• Deje que la aspiradora se enfríe antes de

almacenarla, especialmente si se va a almacenar en

un lugar cerrado.

• No use bolsas de papel para polvo.

• Para reducir el riesgo de daños por causa de la

recogida accidental de brasas calientes, no coloque

la aspiradora sobre superficies susceptibles a los

daños por calor, tales como alfombras, pisos de

vinilo o superficies de madera.

• No deje desatendida la aspiradora mientras esté en

marcha: Puede que usted no observe señales

importantes que indican un funcionamiento anormal,

tales como pérdida de succión, salida de residuos

por el escape o ruidos anormales del motor. Deje de

usar la aspiradora inmedia tamente si observa estas

señales.

Indice

Sección Página

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 18

• No abandone la aspiradora cuando esté enchufada.

Desenchúfela del tomacorriente cuando no la esté

utilizando y antes de realizar servicio de revisión.

• Las chispas que se producen en el interior del motor

pueden incendiar los vapores inflamables o el polvo.

Para reducir el riesgo de incendio o explosión: No

use la aspiradora cerca de líquidos o gases inflama -

bles o combustibles, o polvos explosivos como

gasolina u otros combustibles, líquido encen dedor,

limpiadores, pinturas a base de aceite, gas natural,

polvo de carbón, polvo de magnesio, polvo de

aluminio, polvo de granos de cereal o pólvora.

• Para reducir el riesgo de que se produzcan peligros

para la salud causados por vapores o polvo, no

recoja con la aspiradora materiales tóxicos ni la use

cerca de dichas materiales.

• Para reducir el riesgo de descargas eléctricas, no

exponga la aspiradora a la lluvia ni deje que entren

líquidos en el compartimiento del motor. Guarde la

aspiradora en un lugar interior.

• Esta aspiradora de ceniza no se destina para

utilizarse por personas (incluyendo niños) cuyas

capacidades físicas, sensoriales o mentales estén

reducidas, o carezcan de experiencia o conocimiento,

a menos que dichas personas reciban una

supervisión o capacitación para el funcionamiento

del aparato por una persona responsable de su

seguridad.

• No permita que la aspiradora se utilice como un

juguete. Se necesita prestar máxima atención cuando

sea utilizada por niños o cerca de éstos.

• No utilice la aspiradora con un filtro desgarrado o sin

tener instalados el filtro y el tamiz del filtro. Los

residuos secos absorbidos por el impulsor podrían

dañar el motor o ser expulsados de vuelta al aire.

• Apague la aspiradora antes de desenchufarla.

• Para reducir el riesgo de lesiones debidas a un

arranque accidental, desenchufe el cordón de energía

antes de cambiar o limpiar el filtro.

• No desenchufe la aspiradora tirando del cordón. Para

desenchufarla, agarre el enchufe y no el cordón.

• No use la aspiradora con el cordón dañado, el

enchu fe dañado u otras piezas dañadas. Si la

aspira dora no funciona como debe, le faltan piezas,

se ha caído, ha sido dañada, se ha dejado a la

intem perie o se ha caído al agua, llame a servicio

al cliente.

• No maneje el enchufe, el interruptor o la aspiradora

con las manos mojadas.

• No tire de la aspiradora usando el cordón ni la lleve

por el cordón, ni use el cordón como asa, ni cierre

una puerta sobre el cordón, ni tire del cordón alre -

dedor de bordes o esquinas afilados. No pase la

aspiradora en marcha sobre el cordón. Mantenga el

cordón alejado de las superficies calientes.

• Utilice únicamente cordones de extensión que estén

diseñados para uso a la intemperie, tales como

SJW o SJTW. Utilice únicamente cordones de

extensión para intemperie de tres cables que

tengan enchufes de conexión a tierra de tres

terminales y tomacorrientes con conexión a tierra

que acepten el enchufe de la aspiradora. Los

cordones de extensión que estén en malas

condiciones o que tengan cables de tamaño

demasiado pequeño pueden causar peligros de

incendio y descargas eléctricas. Para reducir el

riesgo de estos peligros, asegúrese de que el

cordón esté en buenas condiciones y que el líquido

no entre en contacto con la conexión. No utilice un

cordón de extensión que tenga conductores con un

diámetro menor al calibre 16 (AWG). Para reducir la

pérdida de potencia, utilice un cordón de extensión

de calibre 14 si la longitud es de 25 a 50 pies

(8 a 15 m), y de calibre 12 si la longitud es de

50 pies (15 m) o más.

• Conecte la aspiradora solamente a un toma corriente

conectado a tierra adecuada mente. Consulte las

instrucciones de conexión a tierra.

• No ponga ningún objeto en las aberturas de venti -

lación. No recoja nada con la aspiradora cuando

cualquiera de las aberturas de ventilación esté

bloqueada; mantenga dichas aberturas libres de

polvo, pelusa, pelo o cualquier cosa que pueda

reducir el flujo de aire.

• Mantenga el pelo, la ropa holgada, los dedos y

todas las partes del cuerpo alejados de las aber -

turas y de las piezas móviles.

• Para reducir el riesgo de caídas, tenga cuidado

adicional al limpiar en escaleras.

• Para reducir el riesgo de lesiones de espalda o

caídas, no levante una aspiradora que pese mucho

debido a que contiene líquido o residuos. Vacíe

parcialmente la aspiradora extrayendo los residuos.

• Para reducir el riesgo de lesiones corporales

o daños a la aspiradora, utilice únicamente

accesorios recomendados por Ridgid.

• Para reducir el riesgo de lesiones en los ojos, use

pro tección ocular de seguridad. La utilización de

cual quier aspiradora utilitaria o soplador utilitario

puede hacer que se soplen objetos extraños hacia

los ojos, lo cual puede causar daños graves en los

ojos.

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 19

GUARDE ESTE MANUAL

PRECAUCIÓN:

• Para reducir el riesgo de daños a la audición, use

protectores de oídos cuando utilice la aspiradora

durante muchas horas seguidas o cuando la

emplee en un área ruidosa.

• Para operaciones que generan polvo, use una

máscara antipolvo.

• Las descargas de estática son comunes cuando

la humedad relativa del aire es baja. Si recoge

residuos finos con la aspiradora, se puede

depositar carga estática en la manguera o en la

aspiradora. El mejor remedio para reducir la

frecuencia de las descargas de estática en su casa

o cuando use esta aspiradora es añadir humedad

al aire con un humidificador.

Haga caso de las siguientes advertencias que aparecen

en la boquilla con iluminación (números de catálogo

selectos solamente).

ADVERTENCIA:

• Mantenga las baterías fuera del alcance de los

niños pequeños. Consulte inmediatamente a un

médico si alguien se traga una batería; podrían

ocurrir quemaduras o lesiones graves.

• La batería contiene material a base de

perclorato: Es posible que se requiera un

manejo especial. Consulte www.dtsc.ca.gov/

hazardouswaste/perchlorate.

Haga caso de las siguientes advertencias que aparecen

en la aspiradora.

ADVERTENCIA: Riesgo de incendio y daños

por calor.

Esta aspiradora está diseñada para recoger

cenizas FRÍAS de chimeneas, parrillas, hornos,

ceniceros, etc. No recoja cenizas/brasas que

estén calientes, al rojo o ardiendo. Recoja sólo

cenizas frías. Tenga presente que las

cenizas/brasas pueden estar calientes durante

varios días después del uso. Para reducir el

riesgo de daños por causa de una recogida

accidental de brasas calientes, no ponga la

aspiradora sobre superficies susceptibles a los

daños por calor, tales como alfombras, pisos de

vinilo o superficies de madera. Vacíe el tambor

después de cada uso. Deje que la aspiradora se

enfríe antes de almacenarla, especialmente en

espacios cerrados. No utilice bolsas de

recolección de polvo.

ADVERTENCIA: Riesgo de descargas

eléctricas.

Para su propia seguridad, lea y entienda el

manual del usuario. No deje desatendida la

aspiradora cuando esté en marcha. No recoja

materiales tóxicos o inflamables, ni otros

materiales peligrosos. No utilice la aspiradora

cerca de líquidos o vapores explosivos. Para

reducir el riesgo de descargas eléctricas, no use

la aspiradora sobre superficies mojadas. No la

exponga a la lluvia. Almacénela en un lugar

interior. Esta aspiradora está diseñada para

recoger residuos secos solamente; no aspire

NUNCA líquidos con este producto.

SP6957-2 ASH RIDGID_SP6957 5/13/16 11:58 AM Page 20

La page charge ...

RIDGID DV05000 Mode d'emploi

Marque: RIDGID

Modèle: DV05000

Catégorie: Aspirateurs

Taper: Mode d'emploi

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: RIDGID DV05000 User guide
español: RIDGID DV05000 Guía del usuario

Documents connexes

Autres documents

Craftsman CMXEVBE17585 Manuel utilisateur