Identiv UT5501F-01 Manuel utilisateur

Taper
Manuel utilisateur
uTrust 5501 F HF + LF – OEM Integration Manual
Version: 1.1 Page 1 of 5
OEM Integration Manual
for
uTrust 5501 F HF + LF
uTrust 5501 F HF + LF DTC
Author Identiv
Version 1.1
Date 14-DEC-2020
uTrust 5501 F HF + LF – OEM Integration Manual
Version: 1.1 Page 2 of 5
Document History
Version
Date Description of Change Author
1.0 10-NOV-2020 Initial version Identiv
1.1 14-DEC-2020 Revised to comply with FCC KDB 996369 D03
Section 2
Identiv
uTrust 5501 F HF + LF – OEM Integration Manual
Version: 1.1 Page 3 of 5
Table of Contents
1 Scope of the document ....................................................................................................... 4
2 Identiv uTrust 5501 F HF + LF family .................................................................................. 4
3 Host Communication Interface ............................................................................................ 4
4 Integration Guidelines ......................................................................................................... 4
5 Regulatory Information ........................................................................................................ 5
5.1 FCC Statement ................................................................................................................. 5
5.1 ISED Statement ................................................................................................................ 5
uTrust 5501 F HF + LF – OEM Integration Manual
Version: 1.1 Page 4 of 5
1 Scope of the document
This manual provides information for OEMs that integrate the uTrust 5501 F HF + LF into
their own products.
2 Identiv uTrust 5501 F HF + LF family
Identiv uTrust 5501 F HF + LF is a family of USB based contactless card reader. The readers
connect to a host PC via USB 2.0 Full speed interface. They support ISO14443 and
ISO15693 cards in HF mode and 125 KHz LF cards. The information in this manual applies
to the devices model numbers listed below along with their respective part number, FCC ID
and ISED ID:
Part Number
Product Name
FCC ID
ISED ID
905567 uTrust 5501 F HF + LF MBPUT5501F-01 7485A-5501F01
905567-2 uTrust 5501 F HF + LF DTC MBPUT5501F-01 7485A-5501F01
3 Host Communication Interface
Host communication is through the 1x5 header marked USB host.
Pinouts for USB host connector is as below:
PIN # Signal
1 Vbus
2 D-
3 D+
4 GND
5 Shield
The mating connector/receptacle for the header is TE Connectivity 440129-5
4 Integration Guidelines
1. This module is limited to OEM installation only.
2. Module complies with FCC Part 15.225, FCC Part 15.209, FCC Part 15.207 and RSS-
210.
3. End Product Labeling: When the module is installed in host device, the FCC ID label must
be visible through a window on the final device or it must be visible when an access
panel, door or cover is easily removed. If not, a second label must be placed on the
outside of the final device that contains the following text:
“Contains FCC ID: MBPUT5501F-01”. The FCC ID can be used only when all FCC
compliance requirements are met.
For ISED the second label should include “Contains IC: 7485A-5501F01”. The ISED ID
can be used only when all other ISED compliance requirements are met.
4. Installation: The module must be installed such that 10 cm distance is maintained
between the integrated antenna and users.
5. The end user manual shall include all required regulatory information/warning as shown in
this manual.
6. There are no special testing modes for the module. When the module is powered it
automatically start scanning at 13.56 MHz (ASK) and 125 KHz (ASK, FSK, PSK) looking
for tags. When a tag that operates at same frequency and technology responds, the
uTrust 5501 F HF + LF – OEM Integration Manual
Version: 1.1 Page 5 of 5
module locks onto it; the module would not change to other frequency or technology until
the tag leaves the field or stops responding.
7. For FCC Part 15.31 (h) and (k): The integrator (host manufacturer) is responsible for
additional testing to verify compliance as a composite system. When testing the host
device for compliance with Part 15 Subpart B, the host manufacturer is required to show
compliance with Part 15 Subpart B while the module is installer and operating. The
module should be transmitted and the evaluation should confirm that the module’s
intentional emissions are compliant. The host manufacturer must verify that there are no
additional unintentional emissions other than what is permitted in Part 15 Subpart B or
emissions that are compliant with the transmitter’s rules.
5 Regulatory Information
5.1 FCC Statement
FCC PART 15.105 STATEMENT: NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC PART 15.19 STATEMENT: This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
FCC PART 15.21 STATEMENT: NOTE: The grantee is not responsible for any changes or
modifications not expressly approved by the party responsible for compliance. Such
modifications could void the user’s authority to operate the equipment.
5.1 ISED Statement
The device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s license-exempt RSS(s).Operation is subject
to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation of the device.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux
CNR d'Innovation, Sciences et Développement économique Canada applicables aux
appareilsradio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) L' appareil ne doit pas produire de brouillage;
(2) L' appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
estsusceptible d'en compromettre le fonctionnement.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Identiv UT5501F-01 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues