GEM GROUP 100813 Manuel utilisateur

100813
Marque
GEM GROUP
Modèle
100813
Taper
Manuel utilisateur
Operation Overview
Packing
Truman Wireless Charging Accessory Tray
USB-A to USB-C Type Charging Cable
User Manual
Indicating status and protection function
1. LED blue light: Standby
2. LED green light: Charging
3. Blue light flashing: Mobile phone is not correctly placed on the wireless
charger, over temperature protection, or detects metal on the back of the
mobile phone
Note: Only the QC2.0/QC3.0 Standard power adapter can support this
product's fast charging. Adapters are not included with the product.
1. Plug the power adapter into the wall socket
2. USB-A side connects to the power wall adapter, USB-C side connects to
the wireless charger side, the LED light will illuminate blue which means the
unit is ready to charge your device.
3. Place your device on to the wireless charger, the LED light will change
from blue to green which denotes the device is being charged.
USB Adapter
USB Micro Cable
Type-C Interface
Type-C interface
Indicator
Wireless charger
Storage compartment
Storage compartment
Storage compartment
Specification
Input : 5V/2.0A, 9V/2.0A
Output : 5W/7.5W/10W
Transmission Distance: ≤5mm
Efficiency: ≥75%
Product size: L277*W185*H29mm
Truman Wireless Charging
Accessory Tray
Instruction Manual
IC ID: 21530-100813
FCC ID: 2AGR4-100813
FCC Statement
This device complies with part 15 and part 18 of the FCC Rules.
Operation is Subject To the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference
that may cause undesired operation. Changes or modifications not
explicitly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
Note: this equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 and part 18 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and candidate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. During the operation of
device a distance of 15 cm surrounding the device and 20 cm
above the top surface of the device must be respected.
This device complies with Part 18 of the FCC Rules. This
equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
ISED Statement
This device complies with Industry Canada’s license-exempt RSSs.
Operation is subject to the following two conditions:
● This device may not cause interference; and
● This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
● l’appareil ne doit pas produire de brouillage;
● l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
This equipment complies with Canada radiation exposure limits set
forth for an uncontrolled environment.
During the operation of device a distance of 10 cm surrounding the
device and 10 cm above the top surface of the device must be
respected.
Cet équipement est conforme Canada limites d'exposition aux
radiations dans un environnement non contrôlé.
au cours de l'opération de l'appareil sur une distance de 10 cm
autour de l'appareil et de 10 cm
au - dessus de la surface supérieure de l'appareil doit être respecté.
● Increase the separation between the equipment and any other radio
device.
● Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
ISED Statement
‐ English: This device complies with Industry Canada license ‐exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference,
and (2) This device must accept any interference, including interference that may cause
undesired operation of the device. The digital apparatus complies with Canadian CAN ICES‐3
(B)/NMB‐3(B).
‐ French: Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout
brouillageradioélec triquesubi, mêmesi le brouillageest susceptible d'encompromettre le
fonctionnement.
This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed with the maximum permissible gain indicated. Antenna types not included in this list,
having a gain greater than the maximum gain indicated for that type, are strictly prohibited for
use with this device.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types
d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non
inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement
interdits pour l'exploitation de l'émetteur.
FCC Statement
This device complies with part 15 and part 18 of the FCC Rules. Operation is Subject To the
following two conditions:
(1) This device may not cause harmful interference, and (2) this devicemust accept any
interference received, including interference that may cause undesired operation. Changes or
modifications not explicitly approved by the partyresponsible for compliance could void the
user's authority tooperate this equipment.
Note: this equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 and part 18 of the FCC Rules. These limits are designed to
providereasonable protection against harmful interference in a residential installation. This
equipment generates, uses and canradiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference toradio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged totry to correct the
interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
· Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. During the operation of device a distance of 15 cm surrounding the device and 20
cm above the top surface of the device must be respected.
This device complies with Part 18 of the FCC Rules. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
●Increase the separation between the equipment and any other radio device.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
  • Page 1 1
  • Page 2 2
  • Page 3 3

GEM GROUP 100813 Manuel utilisateur

100813
Marque
GEM GROUP
Modèle
100813
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents